Some TCP peers announce a very small MSS option in their SYN and/or
SYN/ACK messages.
This forces the stack to send packets with a very high network/cpu
overhead.
Linux has enforced a minimal value of 48. Since this value includes
the size of TCP options, and that the options can consume up to 40
bytes, this means that each segment can include only 8 bytes of payload.
In some cases, it can be useful to increase the minimal value
to a saner value.
We still let the default to 48 (TCP_MIN_SND_MSS), for compatibility
reasons.
Note that TCP_MAXSEG socket option enforces a minimal value
of (TCP_MIN_MSS). David Miller increased this minimal value
in commit c39508d6f118 ("tcp: Make TCP_MAXSEG minimum more correct.")
from 64 to 88.
We might in the future merge TCP_MIN_SND_MSS and TCP_MIN_MSS.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com> Suggested-by: Jonathan Looney <jtl@netflix.com> Acked-by: Neal Cardwell <ncardwell@google.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Tyler Hicks <tyhicks@canonical.com> Cc: Bruce Curtis <brucec@netflix.com> Cc: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Looney reported that a malicious peer can force a sender
to fragment its retransmit queue into tiny skbs, inflating memory
usage and/or overflow 32bit counters.
TCP allows an application to queue up to sk_sndbuf bytes,
so we need to give some allowance for non malicious splitting
of retransmit queue.
A new SNMP counter is added to monitor how many times TCP
did not allow to split an skb if the allowance was exceeded.
Note that this counter might increase in the case applications
use SO_SNDBUF socket option to lower sk_sndbuf.
CVE-2019-11478 : tcp_fragment, prevent fragmenting a packet when the
socket is already using more than half the allowed space
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jonathan Looney <jtl@netflix.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Tyler Hicks <tyhicks@canonical.com> Cc: Bruce Curtis <brucec@netflix.com> Cc: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Looney reported that TCP can trigger the following crash
in tcp_shifted_skb() :
BUG_ON(tcp_skb_pcount(skb) < pcount);
This can happen if the remote peer has advertized the smallest
MSS that linux TCP accepts : 48
An skb can hold 17 fragments, and each fragment can hold 32KB
on x86, or 64KB on PowerPC.
This means that the 16bit witdh of TCP_SKB_CB(skb)->tcp_gso_segs
can overflow.
Note that tcp_sendmsg() builds skbs with less than 64KB
of payload, so this problem needs SACK to be enabled.
SACK blocks allow TCP to coalesce multiple skbs in the retransmit
queue, thus filling the 17 fragments to maximal capacity.
CVE-2019-11477 -- u16 overflow of TCP_SKB_CB(skb)->tcp_gso_segs
Fixes: 832d11c5cd07 ("tcp: Try to restore large SKBs while SACK processing") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jonathan Looney <jtl@netflix.com> Acked-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Tyler Hicks <tyhicks@canonical.com> Cc: Yuchung Cheng <ycheng@google.com> Cc: Bruce Curtis <brucec@netflix.com> Cc: Jonathan Lemon <jonathan.lemon@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call of unsubscribe_port() which manages the group count and
module refcount from delete_and_unsubscribe_port() looks racy; it's
not covered by the group list lock, and it's likely a cause of the
reported unbalance at port deletion. Let's move the call inside the
group list_mutex to plug the hole.
Async update callbacks are expected to set the old_fb in the new_state
so prepare/cleanup framebuffers are balanced.
Calling drm_atomic_set_fb_for_plane() (which gets a reference of the new
fb and put the old fb) is not required, as it's taken care by
drm_mode_cursor_universal() when calling drm_atomic_helper_update_plane().
Cc: <stable@vger.kernel.org> # v4.19+ Fixes: 539c320bfa97 ("drm/vc4: update cursors asynchronously through atomic") Suggested-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Helen Koike <helen.koike@collabora.com> Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190603165610.24614-5-helen.koike@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Overlay file f_pos is the master copy that is preserved
through copy up and modified on read/write, but only real
fs knows how to SEEK_HOLE/SEEK_DATA and real fs may impose
limitations that are more strict than ->s_maxbytes for specific
files, so we use the real file to perform seeks.
We do not call real fs for SEEK_CUR:0 query and for SEEK_SET:0
requests.
We found that it return success when we set IMMUTABLE_FL flag to a file in
docker even though the docker didn't have the capability
CAP_LINUX_IMMUTABLE.
The commit d1d04ef8572b ("ovl: stack file ops") and dab5ca8fd9dd ("ovl: add
lsattr/chattr support") implemented chattr operations on a regular overlay
file. ovl_real_ioctl() overridden the current process's subjective
credentials with ofs->creator_cred which have the capability
CAP_LINUX_IMMUTABLE so that it will return success in
vfs_ioctl()->cap_capable().
Fix this by checking the capability before cred overridden. And here we
only care about APPEND_FL and IMMUTABLE_FL, so get these information from
inode.
[SzM: move check and call to underlying fs inside inode locked region to
prevent two such calls from racing with each other]
Sven reports:
Commit 1e07d63749 ("drm/nouveau: add kconfig option to turn off nouveau
legacy contexts. (v3)") has caused a build failure for me when I
actually tried that option (CONFIG_NOUVEAU_LEGACY_CTX_SUPPORT=n):
,----
| Kernel: arch/x86/boot/bzImage is ready (#1)
| Building modules, stage 2.
| MODPOST 290 modules
| ERROR: "drm_legacy_mmap" [drivers/gpu/drm/nouveau/nouveau.ko] undefined!
| scripts/Makefile.modpost:91: recipe for target '__modpost' failed
`----
Upstream does not have that problem, as commit bed2dd8421 ("drm/ttm:
Quick-test mmap offset in ttm_bo_mmap()") has removed the use of
drm_legacy_mmap from nouveau_ttm.c. Unfortunately that commit does not
apply in 5.1.9.
The ensuing discussion proposed a number of one-off patches, but no
solid agreement was made, so just revert the commit for now to get
people's systems building again.
Reported-by: Sven Joachim <svenjoac@gmx.de> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Dave Airlie <airlied@redhat.com> Cc: Thomas Backlund <tmb@mageia.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lots of people have reported issues with this patch, and as there does
not seem to be a fix going into Linus's kernel tree any time soon,
revert the commit in the stable trees so as to get people's machines
working properly again.
Reported-by: Vasily Khoruzhick <anarsoul@gmail.com> Reported-by: Hans de Goede <hdegoede@redhat.com> Cc: Jeremy Cline <jeremy@jcline.org> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pcpu_find_block_fit() guarantees that a fit is found within
PCPU_BITMAP_BLOCK_BITS. Iteration is used to determine the first fit as
it compares against the block's contig_hint. This can lead to
incorrectly scanning past the end of the bitmap. The behavior was okay
given the check after for bit_off >= end and the correctness of the
hints from pcpu_find_block_fit().
This patch fixes this by bounding the end offset by the number of bits
in a chunk.
Signed-off-by: Dennis Zhou <dennis@kernel.org> Reviewed-by: Peng Fan <peng.fan@nxp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The datasheet says the vconn MUST be off when we start toggling. The
tcpm.c state-machine is responsible to make sure vconn is off, but lets
add a WARN to catch any cases where vconn is not off for some reason.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During early system resume on Exynos5422 with performance counters enabled
the following kernel oops happens:
Internal error: Oops - undefined instruction: 0 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 1433 Comm: bash Tainted: G W 5.0.0-rc5-next-20190208-00023-gd5fb5a8a13e6-dirty #5480
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
...
Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 4451006a DAC: 00000051
Process bash (pid: 1433, stack limit = 0xb7e0e22f)
...
(reset_ctrl_regs) from [<c0112ad0>] (dbg_cpu_pm_notify+0x1c/0x24)
(dbg_cpu_pm_notify) from [<c014c840>] (notifier_call_chain+0x44/0x84)
(notifier_call_chain) from [<c014cbc0>] (__atomic_notifier_call_chain+0x7c/0x128)
(__atomic_notifier_call_chain) from [<c01ffaac>] (cpu_pm_notify+0x30/0x54)
(cpu_pm_notify) from [<c055116c>] (syscore_resume+0x98/0x3f4)
(syscore_resume) from [<c0189350>] (suspend_devices_and_enter+0x97c/0xe74)
(suspend_devices_and_enter) from [<c0189fb8>] (pm_suspend+0x770/0xc04)
(pm_suspend) from [<c0187740>] (state_store+0x6c/0xcc)
(state_store) from [<c09fa698>] (kobj_attr_store+0x14/0x20)
(kobj_attr_store) from [<c030159c>] (sysfs_kf_write+0x4c/0x50)
(sysfs_kf_write) from [<c0300620>] (kernfs_fop_write+0xfc/0x1e0)
(kernfs_fop_write) from [<c0282be8>] (__vfs_write+0x2c/0x160)
(__vfs_write) from [<c0282ea4>] (vfs_write+0xa4/0x16c)
(vfs_write) from [<c0283080>] (ksys_write+0x40/0x8c)
(ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Undefined instruction is triggered during CP14 reset, because bits: #16
(Secure privileged invasive debug disabled) and #17 (Secure privileged
noninvasive debug disable) are set in DSCR. Those bits depend on SPNIDEN
and SPIDEN lines, which are provided by Secure JTAG hardware block. That
block in turn is powered from cluster 0 (big/Eagle), but the Exynos5422
boots on cluster 1 (LITTLE/KFC).
To fix this issue it is enough to turn on the power on the cluster 0 for
a while. This lets the Secure JTAG block to propagate the needed signals
to LITTLE/KFC cores and change their DSCR.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The sysfs unexport in pwmchip_remove() is completely asymmetric
to what we do in pwmchip_add_with_polarity() and commit 0733424c9ba9
("pwm: Unexport children before chip removal") is a strong indication
that this was wrong to begin with. We should just move
pwmchip_sysfs_unexport() where it belongs, which is right after
pwmchip_sysfs_unexport_children(). In that case, we do not need
separate functions anymore either.
We also really want to remove sysfs irrespective of whether or not
the chip will be removed as a result of pwmchip_remove(). We can only
assume that the driver will be gone after that, so we shouldn't leave
any dangling sysfs files around.
This warning disappears if we move pwmchip_sysfs_unexport() to
the top of pwmchip_remove(), pwmchip_sysfs_unexport_children().
That way it is also outside of the pwm_lock section, which indeed
doesn't seem to be needed.
Moving the pwmchip_sysfs_export() call outside of that section also
seems fine and it'd be perfectly symmetric with pwmchip_remove() again.
So, this patch fixes them.
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
[shimoda: revise the commit log and code] Fixes: 76abbdde2d95 ("pwm: Add sysfs interface") Fixes: 0733424c9ba9 ("pwm: Unexport children before chip removal") Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Tested-by: Hoan Nguyen An <na-hoan@jinso.co.jp> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PVDD_APIO_1V8 (LDO2) and PVDD_ABB_1V8 (LDO8) regulators were turned
off by Linux kernel as unused. However they supply critical parts of
SoC so they should be always on:
1. PVDD_APIO_1V8 supplies SYS pins (gpx[0-3], PSHOLD), HDMI level shift,
RTC, VDD1_12 (DRAM internal 1.8 V logic), pull-up for PMIC interrupt
lines, TTL/UARTR level shift, reset pins and SW-TACT1 button.
It also supplies unused blocks like VDDQ_SRAM (for SROM controller) and
VDDQ_GPIO (gpm7, gpy7).
The LDO2 cannot be turned off (S2MPS11 keeps it on anyway) so
marking it "always-on" only reflects its real status.
2. PVDD_ABB_1V8 supplies Adaptive Body Bias Generator for ARM cores,
memory and Mali (G3D).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It must be made sure that immediate mode is not already set, when
modifying shadow register value in ehrpwm_pwm_disable(). Otherwise
modifications to the action-qualifier continuous S/W force
register(AQSFRC) will be done in the active register.
This may happen when both channels are being disabled. In this case,
only the first channel state will be recorded as disabled in the shadow
register. Later, when enabling the first channel again, the second
channel would be enabled as well. Setting RLDCSF to zero, first, ensures
that the shadow register is updated as desired.
Fixes: 38dabd91ff0b ("pwm: tiehrpwm: Fix disabling of output of PWMs") Signed-off-by: Christoph Vogtländer <c.vogtlaender@sigma-surface-science.com>
[vigneshr@ti.com: Improve commit message] Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Intel IOMMU, when enabled, tries to find the domain of the device,
assuming it's a PCI one, during DMA operations, such as mapping or
unmapping. Since we are splitting the actual PCI device to couple of
children via MFD framework (see drivers/mfd/intel-lpss.c for details),
the DMA device appears to be a platform one, and thus not an actual one
that performs DMA. In a such situation IOMMU can't find or allocate
a proper domain for its operations. As a result, all DMA operations are
failed.
In order to fix this, supply parent of the platform device
to the DMA engine framework and fix filter functions accordingly.
We may rely on the fact that parent is a real PCI device, because no
other configuration is present in the wild.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [for tty parts] Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we aren't checking for the ICE_FC_NONE case for the current
flow control mode. This is causing "Unknown" to be printed for the
current flow control method if flow control is disabled. Fix this by
adding the case for ICE_FC_NONE to print "None".
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We are currently assuming all GPIOs are non-wakeup capable GPIOs as we
not configuring the bank->non_wakeup_gpios like we used to earlier with
platform_data.
Let's add omap_gpio_is_off_wakeup_capable() to make the handling clearer
while considering that later patches may want to configure SoC specific
bank->non_wakeup_gpios for the GPIOs in wakeup domain.
Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: Keerthy <j-keerthy@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Tero Kristo <t-kristo@ti.com> Reported-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a sync bfq_queue has a higher weight than some other queue, and
remains temporarily empty while in service, then, to preserve the
bandwidth share of the queue, it is necessary to plug I/O dispatching
until a new request arrives for the queue. In addition, a timeout
needs to be set, to avoid waiting for ever if the process associated
with the queue has actually finished its I/O.
Even with the above timeout, the device is however not fed with new
I/O for a while, if the process has finished its I/O. If this happens
often, then throughput drops and latencies grow. For this reason, the
timeout is kept rather low: 8 ms is the current default.
Unfortunately, such a low value may cause, on the opposite end, a
violation of bandwidth guarantees for a process that happens to issue
new I/O too late. The higher the system load, the higher the
probability that this happens to some process. This is a problem in
scenarios where service guarantees matter more than throughput. One
important case are weight-raised queues, which need to be granted a
very high fraction of the bandwidth.
To address this issue, this commit lower-bounds the plugging timeout
for weight-raised queues to 20 ms. This simple change provides
relevant benefits. For example, on a PLEXTOR PX-256M5S, with which
gnome-terminal starts in 0.6 seconds if there is no other I/O in
progress, the same applications starts in
- 0.8 seconds, instead of 1.2 seconds, if ten files are being read
sequentially in parallel
- 1 second, instead of 2 seconds, if, in parallel, five files are
being read sequentially, and five more files are being written
sequentially
Driver maintains state machine for processing and completing switch
commands. This patch resets FCF_ASYNC_{SENT|ACTIVE} flag to indicate if the
previous command is active or sent, in order for next GPSC command to
advance the state machine.
[mkp: commit desc typo]
Signed-off-by: Giridhar Malavali <gmalavali@marvell.com> Signed-off-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MSI message address in the RC address space can be 64 bit. The
R-Car PCIe RC supports such a 64bit MSI message address as well.
The code currently uses virt_to_phys(__get_free_pages()) to obtain
a reserved page for the MSI message address, and the return value
of which can be a 64 bit physical address on 64 bit system.
However, the driver only programs PCIEMSIALR register with the bottom
32 bits of the virt_to_phys(__get_free_pages()) return value and does
not program the top 32 bits into PCIEMSIAUR, but rather programs the
PCIEMSIAUR register with 0x0. This worked fine on older 32 bit R-Car
SoCs, however may fail on new 64 bit R-Car SoCs.
Since from a PCIe controller perspective, an inbound MSI is a memory
write to a special address (in case of this controller, defined by
the value in PCIEMSIAUR:PCIEMSIALR), which triggers an interrupt, but
never hits the DRAM _and_ because allocation of an MSI by a PCIe card
driver obtains the MSI message address by reading PCIEMSIAUR:PCIEMSIALR
in rcar_msi_setup_irqs(), incorrectly programmed PCIEMSIAUR cannot
cause memory corruption or other issues.
There is however the possibility that if virt_to_phys(__get_free_pages())
returned address above the 32bit boundary _and_ PCIEMSIAUR was programmed
to 0x0 _and_ if the system had physical RAM at the address matching the
value of PCIEMSIALR, a PCIe card driver could allocate a buffer with a
physical address matching the value of PCIEMSIALR and a remote write to
such a buffer by a PCIe card would trigger a spurious MSI.
Fixes: e015f88c368d ("PCI: rcar: Add support for R-Car H3 to pcie-rcar") Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Simon Horman <horms+renesas@verge.net.au> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: Phil Edworthy <phil.edworthy@renesas.com> Cc: Simon Horman <horms+renesas@verge.net.au> Cc: Wolfram Sang <wsa@the-dreams.de> Cc: linux-renesas-soc@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
When set 2 same MAC to different function of one port, IMP
will return error as the later one may modify the origin one.
This will cause bond fail for 2 VFs of one port.
Driver just print warning and return 0 with this patch, so
if set same MAC address, it will return 0 but do not really
configure HW.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Call order on probe():
- max14656_hw_init() enables interrupts on the chip
- devm_request_irq() starts processing interrupts, isr
could be called immediately
- isr: schedules delayed work (irq_work)
- irq_work: calls power_supply_changed()
- devm_power_supply_register() registers the power supply
Depending on timing, it's possible that power_supply_changed()
is called on an unregistered power supply structure.
Fix by registering the power supply before requesting the irq.
Cc: Alexander Kurz <akurz@blala.de> Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This area is used to store keys by HSPPA in case of AM438x SOC. Leave it
active.
Signed-off-by: Kabir Sahane <x0153567@ti.com> Signed-off-by: Andrew F. Davis <afd@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
The input color space for the plane was previously ignored even if it
was set.
If a limited range YUV format was given to DC then the
wrong color transformation matrix was being used since DC assumed that
it was full range instead.
[How]
Respect the given color_space format for the plane if it isn't
COLOR_SPACE_UNKNOWN. Otherwise, use the implicit default since DM
didn't specify.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com> Acked-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The find_dlpar_node() helper returns a device node with its reference
incremented. Both the add and remove paths use this helper for find the
appropriate node, but fail to release the reference when done.
Annotate the find_dlpar_node() helper with a comment about the incremented
reference count and call of_node_put() on the obtained device_node in the
add and remove paths. Also, fixup a reference leak in the find_vio_slot()
helper where we fail to call of_node_put() on the vdevice node after we
iterate over its children.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6QDL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality(this at least
breaks RAVE SP serdev driver on RDU2). Fix the code to specify
IMX6QDL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting incorrect
clock ratio.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Cc: Angus Ainslie (Purism) <angus@akkea.ca> Cc: Chris Healy <cphealy@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Shawn Guo <shawnguo@kernel.org> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Tested-by: Adam Ford <aford173@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SX_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SX_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6UL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6UL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX7D_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX7D_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SLL_CLK_SDMA result in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SLL_CLK_IPG as "ipg" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX6SL_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX6SL_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
Since 25aaa75df1e6 SDMA driver uses clock rates of "ipg" and "ahb"
clock to determine if it needs to configure the IP block as operating
at 1:1 or 1:2 clock ratio (ACR bit in SDMAARM_CONFIG). Specifying both
clocks as IMX5_CLK_SDMA results in driver incorrectly thinking that
ratio is 1:1 which results in broken SDMA funtionality. Fix the code
to specify IMX5_CLK_AHB as "ahb" clock for SDMA, to avoid detecting
incorrect clock ratio.
The rk3288 SoC has two PWM implementations available, the "old"
implementation and the "new" one. You can switch between the two of
them by flipping a bit in the grf.
The "old" implementation is the default at chip power up but isn't the
one that's officially supposed to be used. ...and, in fact, the
driver that gets selected in Linux using the rk3288 device tree only
supports the "new" implementation.
Long ago I tried to get a switch to the right IP block landed in the
PWM driver (search for "rk3288: Switch to use the proper PWM IP") but
that got rejected. In the mean time the grf has grown a full-fledged
driver that already sets other random bits like this. That means we
can now get the fix landed.
For those wondering how things could have possibly worked for the last
4.5 years, folks have mostly been relying on the bootloader to set
this bit. ...but occasionally folks have pointed back to my old patch
series [1] in downstream kernels.
Experimentally it can be seen that going into deep sleep (specifically
setting PMU_CLR_DMA and PMU_CLR_BUS in RK3288_PMU_PWRMODE_CON1)
appears to fail unless "aclk_dmac1" is on. The failure is that the
system never signals that it made it into suspend on the GLOBAL_PWROFF
pin and it just hangs.
NOTE that it's confirmed that it's the actual suspend that fails, not
one of the earlier calls to read/write registers. Specifically if you
comment out the "PMU_GLOBAL_INT_DISABLE" setting in
rk3288_slp_mode_set() and then comment out the "cpu_do_idle()" call in
rockchip_lpmode_enter() then you can exercise the whole suspend path
without any crashing.
This is currently not a problem with suspend upstream because there is
no current way to exercise the deep suspend code. However, anyone
trying to make it work will run into this issue.
This was not a problem on shipping rk3288-based Chromebooks because
those devices all ran on an old kernel based on 3.14. On that kernel
"aclk_dmac1" appears to be left on all the time.
There are several ways to skin this problem.
A) We could add "aclk_dmac1" to the list of critical clocks and that
apperas to work, but presumably that wastes power.
B) We could keep a list of "struct clk" objects to enable at suspend
time in clk-rk3288.c and use the standard clock APIs.
C) We could make the rk3288-pmu driver keep a list of clocks to enable
at suspend time. Presumably this would require a dts and bindings
change.
D) We could just whack the clock on in the existing syscore suspend
function where we whack a bunch of other clocks. This is particularly
easy because we know for sure that the clock's only parent
("aclk_cpu") is a critical clock so we don't need to do anything more
than ungate it.
In this case I have chosen D) because it seemed like the least work,
but any of the other options would presumably also work fine.
Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Elaine Zhang <zhangqing@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/soc/mediatek/mtk-pmic-wrap.c:1358:6: error: variable 'rdata' is
used uninitialized whenever '||' condition is true
[-Werror,-Wsometimes-uninitialized]
If pwrap_write returns non-zero, pwrap_read will not be called to
initialize rdata, meaning that we will use some random uninitialized
stack value in our print statement. Zero initialize rdata in case this
happens.
hook_fault_code() is an ARM32 specific API for hooking into data abort.
AM65X platforms (that integrate ARM v8 cores and select CONFIG_ARM64 as
arch) rely on pci-keystone.c but on them the enumeration of a
non-present BDF does not trigger a bus error, so the fixup exception
provided by calling hook_fault_code() is not needed and can be guarded
with CONFIG_ARM.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: commit log] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As new transfer mechanisms are added to the EC codebase, they may
not support v2 of the EC protocol.
If the v3 initial handshake transfer fails, the kernel will try
and call cmd_xfer as a fallback. If v2 is not supported, cmd_xfer
will be NULL, and the code will end up causing a kernel panic.
Add a check for NULL before calling the transfer function, along
with a helpful comment explaining how one might end up in this
situation.
Added a new local variable in the i40e_setup_tc function named
old_queue_pairs so num_queue_pairs can be restored to the correct
value in case configuring queue channels fails. Additionally, moved
the exit label in the i40e_setup_tc function so the if (need_reset)
block can be executed.
Also, fixed data packing in the i40e_setup_tc function.
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In pcibios_irq_init(), the PCI IRQ routing table 'pirq_table' is first
found through pirq_find_routing_table(). If the table is not found and
CONFIG_PCI_BIOS is defined, the table is then allocated in
pcibios_get_irq_routing_table() using kmalloc(). Later, if the I/O APIC is
used, this table is actually not used. In that case, the allocated table
is not freed, which is a memory leak.
Free the allocated table if it is not used.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
[bhelgaas: added Ingo's reviewed-by, since the only change since v1 was to
use the irq_routing_table local variable name he suggested] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The XDomain protocol messages may start as soon as Thunderbolt control
channel is started. This means that if the other host starts sending
ThunderboltIP packets early enough they will be passed to the network
driver which then gets confused because its resume hook is not called
yet.
Fix this by unregistering the ThunderboltIP protocol handler when
suspending and registering it back on resume.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running application tool switchtec-user's `firmware update` and `event
wait` commands concurrently, sometimes the firmware update speed reduced
significantly.
It is because when the MRPC event happened after MRPC event occurrence
check but before the event mask loop reaches its header register in event
ISR, the MRPC event would be masked unintentionally. Since there's no
chance to enable it again except for a module reload, all the following
MRPC execution completion checks time out.
Fix this bug by skipping the mask operation for MRPC event in event ISR,
same as what we already do for LINK event.
Disabling the SMMU when probing from within a kdump kernel so that all
incoming transactions are terminated can prevent the core of the crashed
kernel from being transferred off the machine if all I/O devices are
behind the SMMU.
Instead, continue to probe the SMMU after it is disabled so that we can
reinitialise it entirely and re-attach the DMA masters as they are reset.
Since the kdump kernel may not have drivers for all of the active DMA
masters, we suppress fault reporting to avoid spamming the console and
swamping the IRQ threads.
vfio_dev_present() which is the condition to
wait_event_interruptible_timeout(), will call vfio_group_get_device
and try to acquire the mutex group->device_lock.
wait_event_interruptible_timeout() will set the state of the current
task to TASK_INTERRUPTIBLE, before doing the condition check. This
means that we will try to acquire the mutex while already in a
sleeping state. The scheduler warns us by giving the following
warning:
[ 4050.264464] ------------[ cut here ]------------
[ 4050.264508] do not call blocking ops when !TASK_RUNNING; state=1 set at [<00000000b33c00e2>] prepare_to_wait_event+0x14a/0x188
[ 4050.264529] WARNING: CPU: 12 PID: 35924 at kernel/sched/core.c:6112 __might_sleep+0x76/0x90
....
clang warns that 'contextlen' may be accessed without an initialization:
fs/nfsd/nfs4xdr.c:2911:9: error: variable 'contextlen' is uninitialized when used here [-Werror,-Wuninitialized]
contextlen);
^~~~~~~~~~
fs/nfsd/nfs4xdr.c:2424:16: note: initialize the variable 'contextlen' to silence this warning
int contextlen;
^
= 0
Presumably this cannot happen, as FATTR4_WORD2_SECURITY_LABEL is
set if CONFIG_NFSD_V4_SECURITY_LABEL is enabled.
Adding another #ifdef like the other two in this function
avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A fuzzer recently triggered lockdep warnings about potential sb_writers
deadlocks caused by fh_want_write().
Looks like we aren't careful to pair each fh_want_write() with an
fh_drop_write().
It's not normally a problem since fh_put() will call fh_drop_write() for
us. And was OK for NFSv3 where we'd do one operation that might call
fh_want_write(), and then put the filehandle.
But an NFSv4 protocol fuzzer can do weird things like call unlink twice
in a compound, and then we get into trouble.
I'm a little worried about this approach of just leaving everything to
fh_put(). But I think there are probably a lot of
fh_want_write()/fh_drop_write() imbalances so for now I think we need it
to be more forgiving.
Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
FUSE filesystem server and kernel client negotiate during initialization
phase, what should be the maximum write size the client will ever issue.
Correspondingly the filesystem server then queues sys_read calls to read
requests with buffer capacity large enough to carry request header + that
max_write bytes. A filesystem server is free to set its max_write in
anywhere in the range between [1*page, fc->max_pages*page]. In particular
go-fuse[2] sets max_write by default as 64K, wheres default fc->max_pages
corresponds to 128K. Libfuse also allows users to configure max_write, but
by default presets it to possible maximum.
If max_write is < fc->max_pages*page, and in NOTIFY_RETRIEVE handler we
allow to retrieve more than max_write bytes, corresponding prepared
NOTIFY_REPLY will be thrown away by fuse_dev_do_read, because the
filesystem server, in full correspondence with server/client contract, will
be only queuing sys_read with ~max_write buffer capacity, and
fuse_dev_do_read throws away requests that cannot fit into server request
buffer. In turn the filesystem server could get stuck waiting indefinitely
for NOTIFY_REPLY since NOTIFY_RETRIEVE handler returned OK which is
understood by clients as that NOTIFY_REPLY was queued and will be sent
back.
Cap requested size to negotiate max_write to avoid the problem. This
aligns with the way NOTIFY_RETRIEVE handler works, which already
unconditionally caps requested retrieve size to fuse_conn->max_pages. This
way it should not hurt NOTIFY_RETRIEVE semantic if we return less data than
was originally requested.
Please see [1] for context where the problem of stuck filesystem was hit
for real, how the situation was traced and for more involving patch that
did not make it into the tree.
The device tree binding already lists compatible strings for these two
SoCs. They don't have the defect as seen on the H3, and the size and
register layout is the same as the A64. Furthermore, the driver does
not include nvmem cell definitions.
Add support for these two compatible strings, re-using the config for
the A64.
When the bit_offset in the cell is zero, the pointer to the msb will
not be properly initialized (ie, will still be pointing to the first
byte in the buffer).
This being the case, if there are bits to clear in the msb, those will
be left untouched while the mask will incorrectly clear bit positions
on the first byte.
This commit also makes sure that any byte unused in the cell is
cleared.
Currently the IRQ handler in HD-audio controller driver is registered
before the chip initialization. That is, we have some window opened
between the azx_acquire_irq() call and the CORB/RIRB setup. If an
interrupt is triggered in this small window, the IRQ handler may
access to the uninitialized RIRB buffer, which leads to a NULL
dereference Oops.
This is usually no big problem since most of Intel chips do register
the IRQ via MSI, and we've already fixed the order of the IRQ
enablement and the CORB/RIRB setup in the former commit b61749a89f82
("sound: enable interrupt after dma buffer initialization"), hence the
IRQ won't be triggered in that room. However, some platforms use a
shared IRQ, and this may allow the IRQ trigger by another source.
Another possibility is the kdump environment: a stale interrupt might
be present in there, the IRQ handler can be falsely triggered as well.
For covering this small race, let's move the azx_acquire_irq() call
after hda_intel_init_chip() call. Although this is a bit radical
change, it can cover more widely than checking the CORB/RIRB setup
locally in the callee side.
flow_offload_alloc() calls nf_route() to get a dst_entry. Internally,
nf_route() calls ip_route_output_key() that allocates a dst_entry and
holds it. So, a dst_entry should be released by dst_release() if
nf_route() is successful.
Otherwise, netns exit routine cannot be finished and the following
message is printed:
[ 257.490952] unregister_netdevice: waiting for lo to become free. Usage count = 1
We do not restart a controller in a deleting state for timeout errors.
When in this state, unblock potential request dispatchers with failed
completions by shutting down the controller on timeout detection.
Reported-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Just like IO queues, the admin queue also will not be restarted after a
controller shutdown. Unquiesce this queue so that we do not block
request dispatch on a permanently disabled controller.
Reported-by: Yufen Yu <yuyufen@huawei.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Certain platforms like K2G reguires the outbound ATU window to be
aligned. The alignment size is already present in mem->page_size.
Use the alignment size present in mem->page_size to configure an
aligned ATU window. In order to raise an interrupt, CPU has to write
to address offset from the start of the window unlike before where
writes were always to the beginning of the ATU window.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 834b90519925 ("misc: pci_endpoint_test: Add support for
PCI_ENDPOINT_TEST regs to be mapped to any BAR") while adding
test_reg_bar in order to map PCI_ENDPOINT_TEST regs to be mapped to any
BAR failed to update test_reg_bar in pci_endpoint_test, resulting in
test_reg_bar having invalid value when used outside probe.
Fix it.
Fixes: 834b90519925 ("misc: pci_endpoint_test: Add support for PCI_ENDPOINT_TEST regs to be mapped to any BAR") Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The intel_iommu_gfx_mapped flag is exported by the Intel
IOMMU driver to indicate whether an IOMMU is used for the
graphic device. In a virtualized IOMMU environment (e.g.
QEMU), an include-all IOMMU is used for graphic device.
This flag is found to be clear even the IOMMU is used.
Cc: Ashok Raj <ashok.raj@intel.com> Cc: Jacob Pan <jacob.jun.pan@linux.intel.com> Cc: Kevin Tian <kevin.tian@intel.com> Reported-by: Zhenyu Wang <zhenyuw@linux.intel.com> Fixes: c0771df8d5297 ("intel-iommu: Export a flag indicating that the IOMMU is used for iGFX.") Suggested-by: Kevin Tian <kevin.tian@intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
With holding queue's kobject refcount, it is safe for driver
to schedule requeue. However, blk_mq_kick_requeue_list() may
be called after blk_sync_queue() is done because of concurrent
requeue activities, then requeue work may not be completed when
freeing queue, and kernel oops is triggered.
So moving the cancel of requeue_work into blk_mq_release() for
avoiding race between requeue and freeing queue.
Cc: Dongli Zhang <dongli.zhang@oracle.com> Cc: James Smart <james.smart@broadcom.com> Cc: Bart Van Assche <bart.vanassche@wdc.com> Cc: linux-scsi@vger.kernel.org, Cc: Martin K . Petersen <martin.petersen@oracle.com>, Cc: Christoph Hellwig <hch@lst.de>, Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>, Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: James Smart <james.smart@broadcom.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
CONFIG_WATCHDOG_PRETIMEOUT_GOV build symbol adds watchdog_pretimeout.o
object to watchdog.o, the latter is compiled only if CONFIG_WATCHDOG_CORE
is selected, so it rightfully makes sense to add it as a dependency.
The change fixes the next compilation errors, if CONFIG_WATCHDOG_CORE=n
and CONFIG_WATCHDOG_PRETIMEOUT_GOV=y are selected:
drivers/watchdog/pretimeout_noop.o: In function `watchdog_gov_noop_register':
drivers/watchdog/pretimeout_noop.c:35: undefined reference to `watchdog_register_governor'
drivers/watchdog/pretimeout_noop.o: In function `watchdog_gov_noop_unregister':
drivers/watchdog/pretimeout_noop.c:40: undefined reference to `watchdog_unregister_governor'
drivers/watchdog/pretimeout_panic.o: In function `watchdog_gov_panic_register':
drivers/watchdog/pretimeout_panic.c:35: undefined reference to `watchdog_register_governor'
drivers/watchdog/pretimeout_panic.o: In function `watchdog_gov_panic_unregister':
drivers/watchdog/pretimeout_panic.c:40: undefined reference to `watchdog_unregister_governor'
The documentated behavior is: if max_hw_heartbeat_ms is implemented, the
minimum of the set_timeout argument and max_hw_heartbeat_ms should be used.
This patch implements this behavior.
Previously only the first 7bits were used and the input argument was
returned.
Following splat gets triggered when nfnetlink monitor is running while
xtables-nft selftests are running:
net/netfilter/nf_tables_api.c:1272 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
1 lock held by xtables-nft-mul/27006:
#0: 00000000e0f85be9 (&net->nft.commit_mutex){+.+.}, at: nf_tables_valid_genid+0x1a/0x50
Call Trace:
nf_tables_fill_chain_info.isra.45+0x6cc/0x6e0
nf_tables_chain_notify+0xf8/0x1a0
nf_tables_commit+0x165c/0x1740
nf_tables_fill_chain_info() can be called both from dumps (rcu read locked)
or from the transaction path if a userspace process subscribed to nftables
notifications.
In the 'table dump' case, rcu_access_pointer() cannot be used: We do not
hold transaction mutex so the pointer can be NULLed right after the check.
Just unconditionally fetch the value, then have the helper return
immediately if its NULL.
In the notification case we don't hold the rcu read lock, but updates are
prevented due to transaction mutex. Use rcu_dereference_check() to make lockdep
aware of this.
There are situations when memory regions coming from dts may be
too big for the platform physical address space. This especially
concerns XPA-capable systems. Bootloader may determine more than 4GB
memory available and pass it to the kernel over dts memory node, while
kernel is built without XPA/64BIT support. In this case the region
may either simply be truncated by add_memory_region() method
or by u64->phys_addr_t type casting. But in worst case the method
can even drop the memory region if it exceeds PHYS_ADDR_MAX size.
So lets make sure the retrieved from dts memory regions are valid,
and if some of them aren't, just manually truncate them with a warning
printed out.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Thomas Bogendoerfer <tbogendoerfer@suse.de> Cc: Huacai Chen <chenhc@lemote.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Juergen Gross <jgross@suse.com> Cc: Serge Semin <Sergey.Semin@t-platforms.ru> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit bc7d811ace4a ("netfilter: nf_ct_h323: Convert
CHECK_BOUND macro to function"), NAT traversal for H.323
doesn't work, failing to parse H323-UserInformation.
nf_h323_error_boundary() compares contents of the bitstring,
not the addresses, preventing valid H.323 packets from being
conntrack'd.
This looks like an oversight from when CHECK_BOUND macro was
converted to a function.
To fix it, stop dereferencing bs->cur and bs->end.
Fixes: bc7d811ace4a ("netfilter: nf_ct_h323: Convert CHECK_BOUND macro to function") Signed-off-by: Jakub Jankowski <shasta@toxcorp.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
rhashtable_insert_fast() may return an error value when memory
allocation fails, but flow_offload_add() does not check for errors.
This patch just adds missing error checking.
The IRQ handler, mmci_irq(), loops until all status bits have been cleared.
However, the status bit signaling busy in variant->busy_detect_flag, may be
set even if busy detection isn't monitored for the current request.
This may be the case for the CMD11 when switching the I/O voltage, which
leads to that mmci_irq() busy loops in IRQ context. Fix this problem, by
clearing the status bit for busy, before continuing to validate the
condition for the loop. This is safe, because the busy status detection has
already been taken care of by mmci_cmd_irq().
Overlayfs "fake" path is used for stacked file operations on underlying
files. Operations on files with "fake" path must not generate fsnotify
events with path data, because those events have already been generated at
overlayfs layer and because the reported event->fd for fanotify marks on
underlying inode/filesystem will have the wrong path (the overlayfs path).
random: get_random_bytes called from init_oops_id+0x27/0x34 with crng_init=0
---[ end trace 00173d0117a88acb ]---
Calibrating delay loop... 6941.90 BogoMIPS (lpj=34709504)
Signed-off-by: Maciej Żenczykowski <maze@google.com> Cc: Jeff Dike <jdike@addtoit.com> Cc: Richard Weinberger <richard@nod.at> Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com> Cc: linux-um@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
In configfs_register_group(), if create_default_group() failed, we
forget to unlink the group. It will left a invalid item in the parent list,
which may trigger the use-after-free issue seen below:
BUG: KASAN: use-after-free in __list_add_valid+0xd4/0xe0 lib/list_debug.c:26
Read of size 8 at addr ffff8881ef61ae20 by task syz-executor.0/5996
Memory state around the buggy address: ffff8881ef61ad00: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff8881ef61ad80: 00 00 00 00 00 00 00 00 fc fc fc fc fc fc fc fc
>ffff8881ef61ae00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881ef61ae80: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff8881ef61af00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
Fixes: 5cf6a51e6062 ("configfs: allow dynamic group creation") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In free_percpu() we sometimes call pcpu_schedule_balance_work() to
queue a work item (which does a wakeup) while holding pcpu_lock.
This creates an unnecessary lock dependency between pcpu_lock and
the scheduler's pi_lock. There are other places where we call
pcpu_schedule_balance_work() without hold pcpu_lock, and this case
doesn't need to be different.
Moving the call outside the lock prevents the following lockdep splat
when running tools/testing/selftests/bpf/{test_maps,test_progs} in
sequence with lockdep enabled:
======================================================
WARNING: possible circular locking dependency detected
5.1.0-dbg-DEV #1 Not tainted
------------------------------------------------------
kworker/23:255/18872 is trying to acquire lock: 000000000bc79290 (&(&pool->lock)->rlock){-.-.}, at: __queue_work+0xb2/0x520
but task is already holding lock: 00000000e3e7a6aa (pcpu_lock){..-.}, at: free_percpu+0x36/0x260
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
On below paths, we can have opportunity to readahead inode page
- gc_node_segment -> f2fs_ra_node_page
- gc_data_segment -> f2fs_ra_node_page
- f2fs_fill_dentries -> f2fs_ra_node_page
Unlike synchronized read, on readahead path, we can set page uptodate
before verifying page's checksum, then read_node_page() will trigger
kernel panic once it encounters a uptodated page w/ incorrect checksum.
So considering readahead scenario, we have to do checksum each time
when loading inode page even if it is uptodated.
- Overview
When mounting the attached crafted image and running program, following errors are reported.
Additionally, it hangs on sync after running program.
The image is intentionally fuzzed from a normal f2fs image for testing.
Compile options for F2FS are as follows.
CONFIG_F2FS_FS=y
CONFIG_F2FS_STAT_FS=y
CONFIG_F2FS_FS_XATTR=y
CONFIG_F2FS_FS_POSIX_ACL=y
CONFIG_F2FS_CHECK_FS=y
- Reproduces
cc poc_13.c
mkdir test
mount -t f2fs tmp.img test
cp a.out test
cd test
sudo ./a.out
sync
sit.vblocks and sum valid block count in sit.valid_map may be
inconsistent, segment w/ zero vblocks will be treated as free
segment, while allocating in free segment, we may allocate a
free block, if its bitmap is valid previously, it can cause
kernel crash due to bitmap verification failure.
Anyway, to avoid further serious metadata inconsistence and
corruption, it is necessary and worth to detect SIT
inconsistence. So let's enable check_block_count() to verify
vblocks and valid_map all the time rather than do it only
CONFIG_F2FS_CHECK_FS is enabled.
We may miss xattr data with below testcase:
- mkdir dir
- setfattr -n "user.name" -v 0 dir
- for ((i = 0; i < 190; i++)) do touch dir/$i; done
- umount
- mount
- getfattr -n "user.name" dir
user.name: No such attribute
The root cause is that we persist xattr data into reserved inline xattr
space, even if inline_xattr is not enable in inline directory inode, after
inline dentry conversion, reserved space no longer exists, so that xattr
data missed.
Let's use inline xattr space only if inline_xattr flag is set on inode
to fix this iusse.
Fixes: 6afc662e68b5 ("f2fs: support flexible inline xattr size") Signed-off-by: Chao Yu <yuchao0@huawei.com> Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During inode loading, __recover_inline_status() can recovery inode status
and set inode dirty, once we failed in following process, it will fail
the check in f2fs_evict_inode, result in trigger BUG_ON().
Let's clear dirty inode in error path of f2fs_iget() to avoid panic.
- Overview
When mounting the attached crafted image and unmounting it, following errors are reported.
Additionally, it hangs on sync after unmounting.
The image is intentionally fuzzed from a normal f2fs image for testing.
Compile options for F2FS are as follows.
CONFIG_F2FS_FS=y
CONFIG_F2FS_STAT_FS=y
CONFIG_F2FS_FS_XATTR=y
CONFIG_F2FS_FS_POSIX_ACL=y
CONFIG_F2FS_CHECK_FS=y
- Reproduces
mkdir test
mount -t f2fs tmp.img test
touch test/t
umount test
sync
NAT table is corrupted, so reserved meta/node inode ids were added into
free list incorrectly, during file creation, since reserved id has cached
in inode hash, so it fails the creation and preallocated nid can not be
released later, result in kernel panic.
To fix this issue, let's do nid boundary check during free nid loading.
- Overview
When mounting the attached crafted image and running program, following errors are reported.
Additionally, it hangs on sync after running program.
The image is intentionally fuzzed from a normal f2fs image for testing.
Compile options for F2FS are as follows.
CONFIG_F2FS_FS=y
CONFIG_F2FS_STAT_FS=y
CONFIG_F2FS_FS_XATTR=y
CONFIG_F2FS_FS_POSIX_ACL=y
CONFIG_F2FS_CHECK_FS=y
- Overview
When mounting the attached crafted image, following errors are reported.
Additionally, it hangs on sync after trying to mount it.
The image is intentionally fuzzed from a normal f2fs image for testing.
Compile options for F2FS are as follows.
CONFIG_F2FS_FS=y
CONFIG_F2FS_STAT_FS=y
CONFIG_F2FS_FS_XATTR=y
CONFIG_F2FS_FS_POSIX_ACL=y
CONFIG_F2FS_CHECK_FS=y
- Reproduces
mkdir test
mount -t f2fs tmp.img test
sync
During recovery, if ofs_of_node is inconsistent in between recovered
node page and original checkpointed node page, let's just fail recovery
instead of making kernel panic.
The ADJ_TAI adjtimex mode sets the TAI-UTC offset of the system clock.
It is typically set by NTP/PTP implementations and it is automatically
updated by the kernel on leap seconds. The initial value is zero (which
applications may interpret as unknown), but this value cannot be set by
adjtimex. This limitation seems to go back to the original "nanokernel"
implementation by David Mills.
Change the ADJ_TAI check to accept zero as a valid TAI-UTC offset in
order to allow setting it back to the initial value.
Fixes: 153b5d054ac2 ("ntp: support for TAI") Suggested-by: Ondrej Mosnacek <omosnace@redhat.com> Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Link: https://lkml.kernel.org/r/20190417084833.7401-1-mlichvar@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
On failure of_irq_get() returns a negative value or zero, which is
not handled as an error in the existing implementation.
Instead of using this API, use platform_get_irq() that returns
exclusively a negative value on failure.
Also, do not output an error log in case of defer probe error.
Holding the spin-lock for all of the code in meson_pwm_apply() can
result in a "BUG: scheduling while atomic". This can happen because
clk_get_rate() (which is called from meson_pwm_calc()) may sleep.
Only hold the spin-lock when modifying registers to solve this.
The reason why we need a spin-lock in the driver is because the
REG_MISC_AB register is shared between the two channels provided by one
PWM controller. The only functions where REG_MISC_AB is modified are
meson_pwm_enable() and meson_pwm_disable() so the register reads/writes
in there need to be protected by the spin-lock.
The original code also used the spin-lock to protect the values in
struct meson_pwm_channel. This could be necessary if two consumers can
use the same PWM channel. However, PWM core doesn't allow this so we
don't need to protect the values in struct meson_pwm_channel with a
lock.
Fixes: 211ed630753d2f ("pwm: Add support for Meson PWM Controller") Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> Signed-off-by: Thierry Reding <thierry.reding@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 31fd85816dbe ("bpf: permits narrower load from bpf program
context fields") made the verifier add AND instructions to clear the
unwanted bits with a mask when doing a narrow load. The mask is
computed with
(1 << size * 8) - 1
where "size" is the size of the narrow load. When doing a 4 byte load
of a an 8 byte field the verifier shifts the literal 1 by 32 places to
the left. This results in an overflow of a signed integer, which is an
undefined behavior. Typically, the computed mask was zero, so the
result of the narrow load ended up being zero too.
Cast the literal to long long to avoid overflows. Note that narrow
load of the 4 byte fields does not have the undefined behavior,
because the load size can only be either 1 or 2 bytes, so shifting 1
by 8 or 16 places will not overflow it. And reading 4 bytes would not
be a narrow load of a 4 bytes field.
Fixes: 31fd85816dbe ("bpf: permits narrower load from bpf program context fields") Reviewed-by: Alban Crequy <alban@kinvolk.io> Reviewed-by: Iago López Galeiras <iago@kinvolk.io> Signed-off-by: Krzesimir Nowak <krzesimir@kinvolk.io> Cc: Yonghong Song <yhs@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Cursor position updates were accidentally causing us to attempt to interlock
window with window immediate, and without a matching window immediate update,
NVDisplay could hang forever in some circumstances.
Fixes suspend/resume on (at least) Quadro RTX4000 (TU104).
Reported-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ignore flag is set on fake jumps in order to keep
add_jump_destinations() from setting their jump_dest, since it already
got set when the fake jump was created.
But using the ignore flag is a bit of a hack. It's normally used to
skip validation of an instruction, which doesn't really make sense for
fake jumps.
Also, after the next patch, using the ignore flag for fake jumps can
trigger a false "why am I validating an ignored function?" warning.
Instead just add an explicit check in add_jump_destinations() to skip
fake jumps.
The driver currently sets register 0xfb (Low Refresh Rate) based on the
value of mode->vrefresh. Firstly, this field is specified to be in Hz,
but the magic numbers used by the code are Hz * 1000. This essentially
leads to the low refresh rate always being set to 0x01, since the
vrefresh value will always be less than 24000. Fix the magic numbers to
be in Hz.
Secondly, according to the comment in drm_modes.h, the field is not
supposed to be used in a functional way anyway. Instead, use the helper
function drm_mode_vrefresh().
Fixes: 9c8af882bf12 ("drm: Add adv7511 encoder driver") Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Matt Redfearn <matt.redfearn@thinci.com> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190424132210.26338-1-matt.redfearn@thinci.com Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log