register_snap_client may return NULL, all the callers
check it, but only print a warning. This will result in
NULL pointer dereference in unregister_snap_client and other
places.
It has always been used like this since v2.6
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In qrtr_tun_write_iter the allocated kbuf should be release in case of
error or success return.
v2 Update: Thanks to David Miller for pointing out the release on success
path as well.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas sound device has many IPs and many situations.
If platform/board uses MIXer, situation will be more complex.
To avoid duplicate DVC kctrl registration when MIXer was used,
it had original flags.
But it was issue when sound card was re-binded, because
no one can't cleanup this flags then.
To solve this issue, commit 9c698e8481a15237a ("ASoC: rsnd: tidyup
registering method for rsnd_kctrl_new()") checks registered
card->controls, because if card was re-binded, these were cleanuped
automatically. This patch could solve re-binding issue.
But, it start to avoid MIX kctrl.
To solve these issues, we need below.
To avoid card re-binding issue: check registered card->controls
To avoid duplicate DVC registration: check registered rsnd_kctrl_cfg
To allow multiple MIX registration: check registered rsnd_kctrl_cfg
This patch do it.
Fixes: 9c698e8481a15237a ("ASoC: rsnd: tidyup registering method for rsnd_kctrl_new()") Reported-by: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Tested-By: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xfs_prepare_shift() fails to check the error return from
xfs_flush_unmap_range(). If the latter fails, that could lead to an
insert/collapse range operation over a delalloc range, which is not
supported.
Add an error check and return appropriately. This is reproduced
rarely by generic/475.
Fixes: 7f9f71be84bc ("xfs: extent shifting doesn't fully invalidate page cache") Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Allison Collins <allison.henderson@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Cc: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 4721a601099, we tried to fix a problem wherein directio reads
into a splice pipe will bounce EFAULT/EAGAIN all the way out to
userspace by simulating a zero-byte short read. This happens because
some directio read implementations (xfs) will call
bio_iov_iter_get_pages to grab pipe buffer pages and issue asynchronous
reads, but as soon as we run out of pipe buffers that _get_pages call
returns EFAULT, which the splice code translates to EAGAIN and bounces
out to userspace.
In that commit, the iomap code catches the EFAULT and simulates a
zero-byte read, but that causes assertion errors on regular splice reads
because xfs doesn't allow short directio reads. This causes infinite
splice() loops and assertion failures on generic/095 on overlayfs
because xfs only permit total success or total failure of a directio
operation. The underlying issue in the pipe splice code has now been
fixed by changing the pipe splice loop to avoid avoid reading more data
than there is space in the pipe.
Therefore, it's no longer necessary to simulate the short directio, so
remove the hack from iomap.
Fixes: 4721a601099 ("iomap: dio data corruption and spurious errors when pipes fill") Reported-by: Murphy Zhou <jencce.kernel@gmail.com> Ranted-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 4721a601099, we tried to fix a problem wherein directio reads
into a splice pipe will bounce EFAULT/EAGAIN all the way out to
userspace by simulating a zero-byte short read. This happens because
some directio read implementations (xfs) will call
bio_iov_iter_get_pages to grab pipe buffer pages and issue asynchronous
reads, but as soon as we run out of pipe buffers that _get_pages call
returns EFAULT, which the splice code translates to EAGAIN and bounces
out to userspace.
In that commit, the iomap code catches the EFAULT and simulates a
zero-byte read, but that causes assertion errors on regular splice reads
because xfs doesn't allow short directio reads.
The brokenness is compounded by splice_direct_to_actor immediately
bailing on do_splice_to returning <= 0 without ever calling ->actor
(which empties out the pipe), so if userspace calls back we'll EFAULT
again on the full pipe, and nothing ever gets copied.
Therefore, teach splice_direct_to_actor to clamp its requests to the
amount of free space in the pipe and remove the simulated short read
from the iomap directio code.
Fixes: 4721a601099 ("iomap: dio data corruption and spurious errors when pipes fill") Reported-by: Murphy Zhou <jencce.kernel@gmail.com> Ranted-by: Amir Goldstein <amir73il@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'len' returned by grab_bb() includes an extra MAXINSN bytes to allow
for the last instruction, so the the final 'offs' will not be 'len'.
Fix the error condition logic accordingly.
Before:
$ perf record -e '{intel_pt//,cpu/mem_inst_retired.all_loads,aux-sample-size=8192/pp}:u' grep -rqs jhgjhg /boot
[ perf record: Woken up 19 times to write data ]
[ perf record: Captured and wrote 2.274 MB perf.data ]
$ perf script -F +brstackinsn --xed --itrace=i1usl100 | head
grep 13759 [002] 8091.310257: 1862 instructions:uH: 5641d58069eb bmexec+0x86b (/bin/grep)
bmexec+2485: 00005641d5806b35 jnz 0x5641d5806bd0 # MISPRED 00005641d5806bd0 movzxb (%r13,%rdx,1), %eax 00005641d5806bd6 add %rdi, %rax 00005641d5806bd9 movzxb -0x1(%rax), %edx 00005641d5806bdd cmp %rax, %r14 00005641d5806be0 jnb 0x5641d58069c0 # MISPRED
mismatch of LBR data and executable 00005641d58069c0 movzxb (%r13,%rdx,1), %edi
The ast2600 no longer uses bit 4 in the control register to indicate a
1MHz clock (It now controls whether this watchdog is reset by a SOC
reset). This means we do not want to set it. It also does not need to be
set for the ast2500, as it is read-only on that SoC.
The comment next to the clock rate selection wandered away from where it
was set, so put it back next to the register setting it's describing.
Fixes: b3528b487448 ("watchdog: aspeed: Add support for AST2600") Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20191108032905.22463-1-joel@jms.id.au Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The first argument to WARN() is supposed to be a condition. The
original code will just print the mdname() instead of the full warning
message.
Fixes: c84a1372df92 ("md/raid0: avoid RAID0 data corruption due to layout confusion.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is an alternative fix attemp for the issue reported in the commit caa8422d01e9 ("ALSA: hda: Flush interrupts on disabling") that was
reverted later due to regressions. Instead of tweaking the hardware
disablement order and the enforced irq flushing, do calling
cancel_work_sync() of the unsol work early enough, and explicitly
ignore the unsol events during the shutdown by checking the
bus->shutdown flag.
Fixes: caa8422d01e9 ("ALSA: hda: Flush interrupts on disabling") Cc: Chris Wilson <chris@chris-wilson.co.uk> Link: https://lore.kernel.org/r/s5h1ruxt9cz.wl-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The old loop wouldn't stop when reaching `start` if `start==NULL`, instead
continuing backwards to index -1 and crashing.
Luckily you need to be highly privileged to map things at NULL, so it's not
a big problem.
Fix it by adjusting the loop so that the loop variable is always in bounds.
This patch is deliberately minimal to simplify backporting, but IMO this
function could use a refactor. The jump labels in the second loop body are
horrible (the error gotos should be jumping to free_range instead), and
both loops would look nicer if they just iterated upwards through indices.
And the up_read()+mmput() shouldn't be duplicated like that.
binder_alloc_print_pages() iterates over
alloc->pages[0..alloc->buffer_size-1] under alloc->mutex.
binder_alloc_mmap_handler() writes alloc->pages and alloc->buffer_size
without holding that lock, and even writes them before the last bailout
point.
Unfortunately we can't take the alloc->mutex in the ->mmap() handler
because mmap_sem can be taken while alloc->mutex is held.
So instead, we have to locklessly check whether the binder_alloc has been
fully initialized with binder_alloc_get_vma(), like in
binder_alloc_new_buf_locked().
Commit d21b0be246bf ("vt: introduce unicode mode for /dev/vcs") guarded
against using devices containing attributes as this is not yet
implemented. It however failed to guard against writes to any devices
as this is also unimplemented.
Reported-by: Or Cohen <orcohen@paloaltonetworks.com> Signed-off-by: Nicolas Pitre <npitre@baylibre.com> Cc: <stable@vger.kernel.org> # v4.19+ Cc: Jiri Slaby <jslaby@suse.com> Fixes: d21b0be246bf ("vt: introduce unicode mode for /dev/vcs") Link: https://lore.kernel.org/r/nycvar.YSQ.7.76.1911051030580.30289@knanqh.ubzr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1851799e1d29 ("thermal: Fix use-after-free when unregistering thermal zone
device") changed cancel_delayed_work to cancel_delayed_work_sync to avoid
a use-after-free issue. However, cancel_delayed_work_sync could be called
insides the WQ causing deadlock.
When splicing using iomap_dio_rw() to a pipe, we may leak pipe pages
because bio_iov_iter_get_pages() records that the pipe will have full
extent worth of data however if file size is not block size aligned
iomap_dio_rw() returns less than what bio_iov_iter_get_pages() set up
and splice code gets confused leaking a pipe page with the file tail.
Handle the situation similarly to the old direct IO implementation and
revert iter to actually returned read amount which makes iter consistent
with value returned from iomap_dio_rw() and thus the splice code is
happy.
Fixes: ff6a9292e6f6 ("iomap: implement direct I/O") CC: stable@vger.kernel.org Reported-by: syzbot+991400e8eba7e00a26e1@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The permissions of the read-only or write-only sysfs files can be
changed (as root) and the user can then try to read a write-only file or
write to a read-only file which will lead to kernel crash here.
Protect against that by always validating the show/store callbacks.
In set_mac_address, driver check for interfaces with same bss_type
For first STA entry, this would return 3 interfaces since all priv's have
bss_type as 0 due to kzalloc. Thus mac address gets changed for STA
unexpected. This patch adds check for first STA and avoids mac address
change. This patch also adds mac_address change for p2p based on bss_num
type.
Signed-off-by: Sharvari Harisangam <sharvari@marvell.com> Signed-off-by: Ganapathi Bhat <gbhat@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Cc: Brian Norris <briannorris@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Until a few years ago, this driver was only used with CS GPIO. The
only exception is CS0 on AT91RM9200 which has to use internal CS. A
limitation of the internal CS is that they don't support CS High.
So by using the CS GPIO the CS high configuration was available except
for the particular case CS0 on RM9200.
When the support for the internal chip-select was added, the check of
the CS high support was not updated. Due to this the driver accepts
this configuration for all the SPI controller v2 (used by all SoCs
excepting the AT91RM9200) whereas the hardware doesn't support it for
infernal CS.
This patch fixes the test to match the hardware capabilities.
Fixes: 4820303480a1 ("spi: atmel: add support for the internal chip-select of the spi controller") Cc: <stable@vger.kernel.org> Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com> Link: https://lore.kernel.org/r/20191017141846.7523-3-gregory.clement@bootlin.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The elliptic curve arithmetic library used by the EC-DH KPP implementation
assumes big endian byte order, and unconditionally reverses the byte
and word order of multi-limb quantities. On big endian systems, the byte
reordering is not necessary, while the word ordering needs to be retained.
So replace the __swab64() invocation with a call to be64_to_cpu() which
should do the right thing for both little and big endian builds.
The problem is that desc->entry may be uninitialized in the
async_trigger_callback path where the descriptor was gotten
from ccp_prep_dma_interrupt which got it from ccp_alloc_dma_desc
which doesn't initialize the desc->entry list head. So, just
initialize the list head to avoid the problem.
Cc: <stable@vger.kernel.org> Reported-by: Sahaj Sarup <sahajsarup@gmail.com> Signed-off-by: Mark Salter <msalter@redhat.com> Acked-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when libkcapi test is executed using HW accelerator, cipher operation
return -74.Since af_alg_async_cb->ki_complete treat err as unsigned int,
libkcapi receive 429467222 even though it expect -ve value.
Hence its required to cast resultlen to int so that proper
error is returned to libkcapi.
commit 394a9e044702 ("crypto: cfb - add missing 'chunksize' property")
adds a test vector where the input length is smaller than the IV length
(the second test vector). This revealed a NULL pointer dereference in
the atmel-aes driver, that is caused by passing an incorrect offset in
scatterwalk_map_and_copy() when atmel_aes_complete() is called.
Do not save the IV in req->info of ablkcipher_request (or equivalently
req->iv of skcipher_request) when req->nbytes < ivsize, because the IV
will not be further used.
While touching the code, modify the type of ivsize from int to
unsigned int, to comply with the return type of
crypto_ablkcipher_ivsize().
Fixes: 91308019ecb4 ("crypto: atmel-aes - properly set IV after {en,de}crypt") Cc: <stable@vger.kernel.org> Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a crash that can happen during probe
when the available dma memory is not enough (this can
happen if the crypto4xx is built as a module).
The descriptor window mapping would end up being free'd
twice, once in crypto4xx_build_pdr() and the second time
in crypto4xx_destroy_sdr().
Acquire kvm->srcu for the duration of ->set_nested_state() to fix a bug
where nVMX derefences ->memslots without holding ->srcu or ->slots_lock.
The other half of nested migration, ->get_nested_state(), does not need
to acquire ->srcu as it is a purely a dump of internal KVM (and CPU)
state to userspace.
Detected as an RCU lockdep splat that is 100% reproducible by running
KVM's state_test selftest with CONFIG_PROVE_LOCKING=y. Note that the
failing function, kvm_is_visible_gfn(), is only checking the validity of
a gfn, it's not actually accessing guest memory (which is more or less
unsupported during vmx_set_nested_state() due to incorrect MMU state),
i.e. vmx_set_nested_state() itself isn't fundamentally broken. In any
case, setting nested state isn't a fast path so there's no reason to go
out of our way to avoid taking ->srcu.
KVM does not implement MSR_IA32_TSX_CTRL, so it must not be presented
to the guests. It is also confusing to have !ARCH_CAP_TSX_CTRL_MSR &&
!RTM && ARCH_CAP_TAA_NO: lack of MSR_IA32_TSX_CTRL suggests TSX was not
hidden (it actually was), yet the value says that TSX is not vulnerable
to microarchitectural data sampling. Fix both.
Cc: stable@vger.kernel.org Tested-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"Shared MSRs" are guest MSRs that are written to the host MSRs but
keep their value until the next return to userspace. They support
a mask, so that some bits keep the host value, but this mask is
only used to skip an unnecessary MSR write and the value written
to the MSR is always the guest MSR.
Fix this and, while at it, do not update smsr->values[slot].curr if
for whatever reason the wrmsr fails. This should only happen due to
reserved bits, so the value written to smsr->values[slot].curr
will not match when the user-return notifier and the host value will
always be restored. However, it is untidy and in rare cases this
can actually avoid spurious WRMSRs on return to userspace.
Cc: stable@vger.kernel.org Reviewed-by: Jim Mattson <jmattson@google.com> Tested-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible that two LPIs locate in the same "byte_offset" but target
two different vcpus, where their pending status are indicated by two
different pending tables. In such a scenario, using last_byte_offset
optimization will lead KVM relying on the wrong pending table entry.
Let us use last_ptr instead, which can be treated as a byte index into
a pending table and also, can be vcpu specific.
Commit ef72171b3621 ("arm64: dts: exynos: Remove unneeded address space
mapping for soc node") changed the address and size cells in root node from
2 to 1, but /memory nodes for the affected boards were not updated. This
went unnoticed on Exynos5433-based TM2(e) boards, because they use u-boot,
which updates /memory node to the correct values. On the other hand, the
mentioned commit broke boot on Exynos7-based Espresso board, which
bootloader doesn't touch /memory node at all.
This patch reverts commit ef72171b3621 ("arm64: dts: exynos: Remove
unneeded address space mapping for soc node"), so Exynos5433 and Exynos7
SoCs again matches other ARM64 platforms with 64bit mappings in root
node.
Reported-by: Alim Akhtar <alim.akhtar@samsung.com> Fixes: ef72171b3621 ("arm64: dts: exynos: Remove unneeded address space mapping for soc node") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Cc: <stable@vger.kernel.org> # 5.3.x: 72ddcf6aa224 arm64: dts: exynos: Move GPU under /soc node for Exynos5433 Cc: <stable@vger.kernel.org> # 5.3.x: ede87c3a2bdb arm64: dts: exynos: Move GPU under /soc node for Exynos7 Cc: <stable@vger.kernel.org> # 4.18.x Tested-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "used" variables here come from the user in the ioctl and it can be
negative. It could result in an out of bounds write.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20191004102251.GC823@mwanda Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a process is interrupted while accessing the "gpu" debugfs file and
the drm device struct_mutex is contended, release() could return early
and fail to free related resources.
Note that the return value from release() is ignored.
Fixes: 4f776f4511c7 ("drm/msm/gpu: Convert the GPU show function to use the GPU state") Cc: stable <stable@vger.kernel.org> # 4.18 Cc: Jordan Crouse <jcrouse@codeaurora.org> Cc: Rob Clark <robdclark@gmail.com> Reviewed-by: Rob Clark <robdclark@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20191010131333.23635-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When number of free space in the journal is very low, the arithmetic in
jbd2_log_space_left() could underflow resulting in very high number of
free blocks and thus triggering assertion failure in transaction commit
code complaining there's not enough space in the journal:
J_ASSERT(journal->j_free > 1);
Properly check for the low number of free blocks.
CC: stable@vger.kernel.org Reviewed-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20191105164437.32602-1-jack@suse.cz Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the 32bit ino wraps around, kernfs increments the generation
number to distinguish reused ino instances. The wrap-around detection
tests whether the allocated ino is lower than what the cursor but the
cursor is pointing to the next ino to allocate so the condition never
triggers.
Fix it by remembering the last ino and comparing against that.
Slcan_open doesn't clean-up device which registration failed from the
slcan_devs device list. On next open this list is iterated and freed
device is accessed. Fix this by calling slc_free_netdev in error path.
Driver/net/can/slcan.c is derived from slip.c. Use-after-free error was
identified in slip_open by syzboz. Same bug is in slcan.c. Here is the
trace from the Syzbot slip report:
Do not try to handle keycodes that are too big, otherwise we risk doing
out-of-bounds writes:
BUG: KASAN: global-out-of-bounds in clear_bit include/asm-generic/bitops-instrumented.h:56 [inline]
BUG: KASAN: global-out-of-bounds in kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
BUG: KASAN: global-out-of-bounds in kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
Write of size 8 at addr ffffffff89a1b2d8 by task syz-executor108/1722
...
kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
input_to_handler+0x3b6/0x4c0 drivers/input/input.c:118
input_pass_values.part.0+0x2e3/0x720 drivers/input/input.c:145
input_pass_values drivers/input/input.c:949 [inline]
input_set_keycode+0x290/0x320 drivers/input/input.c:954
evdev_handle_set_keycode_v2+0xc4/0x120 drivers/input/evdev.c:882
evdev_do_ioctl drivers/input/evdev.c:1150 [inline]
In this case we were dealing with a fuzzed HID device that declared over
12K buttons, and while HID layer should not be reporting to us such big
keycodes, we should also be defensive and reject invalid data ourselves as
well.
Even when mounting modern protocol version the server may be
configured without supporting SMB2.1 leases and the client
uses SMB2 oplock to optimize IO performance through local caching.
However there is a problem in oplock break handling that leads
to missing a break notification on the client who has a file
opened. It latter causes big latencies to other clients that
are trying to open the same file.
The problem reproduces when there are multiple shares from the
same server mounted on the client. The processing code tries to
match persistent and volatile file ids from the break notification
with an open file but it skips all share besides the first one.
Fix this by looking up in all shares belonging to the server that
issued the oplock break.
Cc: Stable <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when the client creates a cifsFileInfo structure for
a newly opened file, it allocates a list of byte-range locks
with a pointer to the new cfile and attaches this list to the
inode's lock list. The latter happens before initializing all
other fields, e.g. cfile->tlink. Thus a partially initialized
cifsFileInfo structure becomes available to other threads that
walk through the inode's lock list. One example of such a thread
may be an oplock break worker thread that tries to push all
cached byte-range locks. This causes NULL-pointer dereference
in smb2_push_mandatory_locks() when accessing cfile->tlink:
Fix this by reordering initialization steps of the cifsFileInfo
structure: initialize all the fields first and then add the new
byte-range lock list to the inode's lock list.
Cc: Stable <stable@vger.kernel.org> Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by: Aurelien Aptel <aaptel@suse.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the current implementation, phydev cannot be removed:
$ ip link add dummy type dummy
$ ip link add xfrm1 type xfrm dev dummy if_id 1
$ ip l d dummy
kernel:[77938.465445] unregister_netdevice: waiting for dummy to become free. Usage count = 1
Manage it like in ip tunnels, ie just keep the ifindex. Not that the side
effect, is that the phydev is now optional.
dev_net(dev) is the netns of the device and xi->net is the link netns,
where the device has been linked.
changelink() must operate in the link netns to avoid a corruption of
the xfrm lists.
Note that xi->net and dev_net(xi->physdev) are always the same.
Before the patch, the xfrmi lists may be corrupted and can later trigger a
kernel panic.
The new parameters must not be stored in the netdev_priv() before
validation, it may corrupt the interface. Note also that if data is NULL,
only a memset() is done.
$ ip link add xfrm1 type xfrm dev lo if_id 1
$ ip link add xfrm2 type xfrm dev lo if_id 2
$ ip link set xfrm1 type xfrm dev lo if_id 2
RTNETLINK answers: File exists
$ ip -d link list dev xfrm1
5: xfrm1@lo: <NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/none 00:00:00:00:00:00 brd 00:00:00:00:00:00 promiscuity 0 minmtu 68 maxmtu 1500
xfrm if_id 0x2 addrgenmode eui64 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535
The following commands produce a backtrace and return an error but the xfrm
interface is created (in the wrong netns):
$ ip netns add foo
$ ip netns add bar
$ ip -n foo netns set bar 0
$ ip -n foo link add xfrmi0 link-netnsid 0 type xfrm dev lo if_id 23
RTNETLINK answers: Invalid argument
$ ip -n bar link ls xfrmi0
2: xfrmi0@lo: <NOARP,M-DOWN> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/none 00:00:00:00:00:00 brd 00:00:00:00:00:00
In fact, each time a xfrm interface was created, a netdev was allocated
by __rtnl_newlink()/rtnl_create_link() and then another one by
xfrmi_newlink()/xfrmi_create(). Only the second one was registered, it's
why the previous commands produce a backtrace: dev_change_net_namespace()
was called on a netdev with reg_state set to NETREG_UNINITIALIZED (the
first one).
The AMD FCH USB XHCI Controller advertises support for generating PME#
while in D0. When in D0, it does signal PME# for USB 3.0 connect events,
but not for USB 2.0 or USB 1.1 connect events, which means the controller
doesn't wake correctly for those events.
00:10.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller [1022:7914] (rev 20) (prog-if 30 [XHCI])
Subsystem: Dell FCH USB XHCI Controller [1028:087e]
Capabilities: [50] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Clear PCI_PM_CAP_PME_D0 in dev->pme_support to indicate the device will not
assert PME# from D0 so we don't rely on it.
The job of vmalloc_sync_all() is to help the lazy freeing of vmalloc()
ranges: before such vmap ranges are reused we make sure that they are
unmapped from every task's page tables.
This is really easy on pagetable setups where the kernel page tables
are shared between all tasks - this is the case on 32-bit kernels
with SHARED_KERNEL_PMD = 1.
But on !SHARED_KERNEL_PMD 32-bit kernels this involves iterating
over the pgd_list and clearing all pmd entries in the pgds that
are cleared in the init_mm.pgd, which is the reference pagetable
that the vmalloc() code uses.
In that context the current practice of vmalloc_sync_all() iterating
until FIX_ADDR_TOP is buggy:
This is mostly harmless for the FIX_ADDR and CPU_ENTRY_AREA ranges
that don't clear their pmds, but it's lethal for the LDT range,
which relies on having different mappings in different processes,
and 'synchronizing' them in the vmalloc sense corrupts those
pagetable entries (clearing them).
This got particularly prominent with PTI, which turns SHARED_KERNEL_PMD
off and makes this the dominant mapping mode on 32-bit.
To make LDT working again vmalloc_sync_all() must only iterate over
the volatile parts of the kernel address range that are identical
between all processes.
So the correct check in vmalloc_sync_all() is "address < VMALLOC_END"
to make sure the VMALLOC areas are synchronized and the LDT
mapping is not falsely overwritten.
The CPU_ENTRY_AREA and the FIXMAP area are no longer synced either,
but this is not really a proplem since their PMDs get established
during bootup and never change.
This change fixes the ldt_gdt selftest in my setup.
[ mingo: Fixed up the changelog to explain the logic and modified the
copying to only happen up until VMALLOC_END. ]
Navid Emamdoost [Thu, 21 Nov 2019 20:01:11 +0000 (14:01 -0600)]
Input: Fix memory leak in psxpad_spi_probe
In the implementation of psxpad_spi_probe() the allocated memory for
pdev is leaked if psxpad_spi_init_ff() or input_register_polled_device()
fail. The solution is using device managed allocation, like the one used
for pad. Perform the allocation using
devm_input_allocate_polled_device().
Fixes: 8be193c7b1f4 ("Input: add support for PlayStation 1/2 joypads connected via SPI") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A number of issues are fixed relating to sysfs input validation:-
1) bb_ctrl_store() - incorrect compare of bit select field to absolute
value. Reworked per ETMv4 specification.
2) seq_event_store() - incorrect mask value - register has two
event values.
3) cyc_threshold_store() - must mask with max before checking min
otherwise wrapped values can set illegal value below min.
4) res_ctrl_store() - update to mask off all res0 bits.
Reviewed-by: Leo Yan <leo.yan@linaro.org> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Signed-off-by: Mike Leach <mike.leach@linaro.org> Fixes: a77de2637c9eb ("coresight: etm4x: moving sysFS entries to a dedicated file") Cc: stable <stable@vger.kernel.org> # 4.9+ Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org> Link: https://lore.kernel.org/r/20191104181251.26732-6-mathieu.poirier@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The touchscreen on the Teclast X89 is mounted upside down in relation to
the display orientation (the touchscreen itself is mounted upright, but the
display is mounted upside-down). Add a quirk for this so that we send
coordinates which match the display orientation.
This increment of rmi_smbus in rmi_smb_read/write_block() causes
garbage to be read/written.
The first read of SMB_MAX_COUNT bytes is fine, but after that
it is nonsense. Trial-and-error showed that by dropping the
increment of rmiaddr everything is fine and the F54 function
properly works.
I tried a hack with rmi_smb_write_block() as well (writing to the
same F54 touchpad data area, then reading it back), and that
suggests that there too the rmiaddr increment has to be dropped.
It makes sense that if it has to be dropped for read, then it has
to be dropped for write as well.
It looks like the initial work with F54 was done using i2c, not smbus,
and it seems nobody ever tested F54 with smbus. The other functions
all read/write less than SMB_MAX_COUNT as far as I can tell, so this
issue was never noticed with non-F54 functions.
With this change I can read out the touchpad data correctly on my
Lenovo X1 Carbon 6th Gen laptop.
F34 is a bit special as it reinitializes the device and related driver
structs during the firmware update. This clears the fn_irq_mask which
will then prevent F34 from receiving further interrupts, leading to
timeouts during the firmware update. Make sure to reinitialize the
IRQ enables at the appropriate times.
The issue is in F34 code, but the commit in the fixes tag exposed the
issue, as before this commit things would work by accident.
syzkaller reported an invalid access in PCM OSS read, and this seems
to be an overflow of the internal buffer allocated for a plugin.
Since the rate plugin adjusts its transfer size dynamically, the
calculation for the chained plugin might be bigger than the given
buffer size in some extreme cases, which lead to such an buffer
overflow as caught by KASAN.
Fix it by limiting the max transfer size properly by checking against
the destination size in each plugin transfer callback.
Laptops like ASUS UX431FLC and UX431FL can share the same audio quirks.
But UX431FLC needs one more step to enable the internal speaker: Pull
the GPIO from CODEC to initialize the AMP.
Fixes: 60083f9e94b2 ("ALSA: hda/realtek - Enable internal speaker & headset mic of ASUS UX431FL") Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191125093405.5702-1-jian-hong@endlessm.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the quota/period ratio was changed during this scaling due to
precision loss, it will cause inconsistency between parent and child
task groups.
See below example:
A userspace container manager (kubelet) does three operations:
1) Create a parent cgroup, set quota to 1,000us and period to 10,000us.
2) Create a few children cgroups.
3) Set quota to 1,000us and period to 10,000us on a child cgroup.
These operations are expected to succeed. However, if the scaling of
147/128 happens before step 3, quota and period of the parent cgroup
will be changed:
Set RSS indirection table and RSS hash key sizes to their real size.
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a micro SD card is inserted in the PDU001 card cage, the card
detection switch is opened and the corresponding GPIO input is driven
by a pull-up. Hence change the active level of the card detection
input from low to high.
Signed-off-by: Felix Brack <fb@ltec.ch> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver tries to figure out which state a SD clock is in when the
clock is registered, instead of setting a known state. This can be
problematic for two reasons.
1. If the clock driver can't figure out the state of the clock,
registration of the clock fails, and setting of a known state by a
clock user is not possible.
2. The state of the clock depends on if and how the bootloader
configured it. The driver only checks that the rate is known, not if
the clock is stopped or not for example.
Fix this by setting a known state and making sure the clock is stopped.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/usb/mtu3/mtu3_qmu.c: In function 'qmu_tx_zlp_error_handler':
drivers/usb/mtu3/mtu3_qmu.c:385:22: warning:
variable 'req' set but not used [-Wunused-but-set-variable]
It seems dbginfo original intention is print 'req' other than 'mreq'
drivers/infiniband/hw/mlx4/sysfs.c:360:2: warning: 'strncpy' output may be
truncated copying 8 bytes from a string of length 31
[-Wstringop-truncation]
By eliminating the temporary stack buffer.
Signed-off-by: Qian Cai <cai@gmx.us> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to sdma_progress() is called outside the wait lock.
In this case, there is a race condition where sdma_progress() can return
false and the sdma_engine can idle. If that happens, there will be no
more sdma interrupts to cause the wakeup and the vnic_sdma xmit will hang.
Fix by moving the lock to enclose the sdma_progress() call.
Also, delete the tx_retry. The need for this was removed by:
commit bcad29137a97 ("IB/hfi1: Serve the most starved iowait entry first")
Fixes: 64551ede6cd1 ("IB/hfi1: VNIC SDMA support") Reviewed-by: Gary Leshner <Gary.S.Leshner@intel.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When it is requested to change its physical state back to Offline while in
the process to go up, DC8051 will set the ERROR field in the
DC8051_DBG_ERR_INFO_SET_BY_8051 register. This ERROR field will remain
until the next time when DC8051 transitions from Offline to Polling.
Subsequently, when the host requests DC8051 to change its physical state
to Polling again, it may receive a DC8051 interrupt with the stale ERROR
field still in DC8051_DBG_ERR_INFO_SET_BY_8051. If the host link state has
been changed to Polling, this stale ERROR will force the host to
transition to Offline state, resulting in a vicious cycle of Polling
->Offline->Polling->Offline. On the other hand, if the host link state is
still Offline when the stale ERROR is received, the stale ERROR will be
ignored, and the link will come up correctly. This patch implements the
correct behavior by changing host link state to Polling only after DC8051
changes its physical state to Polling.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by: Krzysztof Goreczny <krzysztof.goreczny@intel.com> Signed-off-by: Kaike Wan <kaike.wan@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.
Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.
Fixes: 4607f6d26950 ("mlxsw: spectrum_router: Support IPv4 underlay decap") Signed-off-by: Nir Dotan <nird@mellanox.com> Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The workaround for the wrong hierarchy of the 3DG-{A,B} power
domains on R-Car E3 ES1.0 corrected the parent domains.
However, the 3DG-{A,B} power domains were still initialized and powered
in the wrong order, causing 3DG operation to fail.
Fix this by changing the order in the table at runtime, when running on
an affected SoC.
If for some reason an association's fragmentation point is zero,
sctp_datamsg_from_user will try to endlessly try to divide a message
into zero-sized chunks. This eventually causes kernel panic due to
running out of memory.
Although this situation is quite unlikely, it has occurred before as
reported. I propose to add this simple last-ditch sanity check due to
the severity of the potential consequences.
Signed-off-by: Jakub Audykowicz <jakub.audykowicz@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Drop the halt check of the UFS symbol clocks, in accordance with other
platforms. This makes clk_disable_unused() happy and makes it possible
to turn the clocks on again without an error.
usb_control_msg returns in case of a successfully sent message the number
of sent bytes as a positive number. Don't use this value as a return value
for stk_camera_read_reg, as a non-zero return value is used as an error
condition in some cases when stk_camera_read_reg is called.
Signed-off-by: Andreas Pape <ap@ca-pape.de> Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There might be situations where tty_ldisc_lock() has blocked, but there
is already IO on tty and it prevents line discipline changes.
It might theoretically turn into dead-lock.
Basically, provide more priority to pending tty_ldisc_lock() than to
servicing reads/writes over tty.
User-visible issue was reported by Mikulas where on pa-risc with
Debian 5 reboot took either 80 seconds, 3 minutes or 3:25 after proper
locking in tty_reopen().
Unlike in previous generations, the system-control register range is not
limited to a size of 0x30 on the H3. In particular, the EMAC clock
configuration register (accessed through syscon) is at offset 0x30 in
that range.
Extend the register size to its full range (0x1000) as a result.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com> Acked-by: Chen-Yu Tsai <wens@csie.org> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Transfers were being divided into device FIFO sized (64 byte max)
operations which would poll for completion within a spin_lock_irqsave /
spin_unlock_irqrestore block. This both made things slow by waiting for
the FIFO to completely drain before adding further data and would also
result in softlocks on large transmissions.
This patch allows larger transfers with continuous FIFO additions as
space becomes available and removes polling from the interrupt handler.
Signed-off-by: Ryan Case <ryandcase@chromium.org> Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The streaming object is a key part of handling the UVC device. Although
not critical, we are currently missing a call to destroy the mutex on
clean up paths, and we are due to extend the objects complexity in the
near future.
Facilitate easy management of a stream object by creating a pair of
functions to handle creating and destroying the allocation. The new
uvc_stream_delete() function also performs the missing mutex_destroy()
operation.
Previously a failed streaming object allocation would cause
uvc_parse_streaming() to return -EINVAL, which is inappropriate. If the
constructor failes, we will instead return -ENOMEM.
While we're here, fix the trivial spelling error in the function banner
of uvc_delete().
As the man(2) page for utime/utimes states, EPERM is returned when the
second parameter of utime or utimes is not NULL, the caller's effective UID
does not match the owner of the file, and the caller is not privileged.
However, in a NFS directory mounted from knfsd, it will return EACCES
(from nfsd_setattr-> fh_verify->nfsd_permission). This patch fixes
that.
Signed-off-by: zhengbin <zhengbin13@huawei.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The add_ssaaaa, sub_ddmmss, umul_ppmm and udiv_qrnnd macros originate
from GCC's longlong.h which in turn was copied from GMP's longlong.h a
few decades ago.
This was found when compiling with clang:
arch/powerpc/math-emu/fnmsub.c:46:2: error: invalid use of a cast in a
inline asm context requiring an l-value: remove the cast or build with
-fheinous-gnu-extensions
FP_ADD_D(R, T, B);
^~~~~~~~~~~~~~~~~
...
Segher points out: this was fixed in GCC over 16 years ago
( https://gcc.gnu.org/r56600 ), and in GMP (where it comes from)
presumably before that.
Update the add_ssaaaa, sub_ddmmss, umul_ppmm and udiv_qrnnd macros to
the latest GCC version in order to git rid of the invalid casts. These
were taken as-is from GCC's longlong in order to make future syncs
obvious. Other parts of sfp-machine.h were left as-is as the file
contains more features than present in longlong.h.
Link: https://github.com/ClangBuiltLinux/linux/issues/260 Signed-off-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Given corruption in the ftrace records, it might be possible to allocate
tmp_prz without assigning prz to it, but still marking it as needing to
be freed, which would cause at least a NULL dereference.
smatch warnings:
fs/pstore/ram.c:340 ramoops_pstore_read() error: we previously assumed 'prz' could be null (see line 255)
Functions __set_port_type and mlx4_check_port_params returned
-EINVAL while the proper return code is -EOPNOTSUPP as a
result of an unsupported operation. All drivers should generate
this and all users should check for it when detecting an
unsupported functionality.
Signed-off-by: Erez Alfasi <ereza@mellanox.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The warning added in commit 3b0e761ba83
"dlm: print log message when cluster name is not set"
did not account for the fact that lockspaces created
from userland do not supply a cluster name, so bogus
warnings are printed every time a userland lockspace
is created.
Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There's a bug in dtc in checking for duplicate node names when there's
another section (e.g. "/ { };"). In this case, skeleton.dtsi provides
another section. Upon removal of skeleton.dtsi, the dtb fails to build
due to a duplicate node 'fixedregulator@0'. As both nodes were pretty
much the same 3.3V fixed regulator, it hasn't really mattered. Fix this
by renaming the nodes to something unique. In the process, drop the
unit-address which shouldn't be present wtihout reg property.
Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike the other PLLs on Meson8b the N value "vid_pll_dco" (a better
name would be hdmi_pll_dco or - as the datasheet calls it - HPLL) is
located at HHI_VID_PLL_CNTL[14:10] instead of [13:9].
This results in an incorrect calculation of the rate of this PLL because
the value seen by the kernel is double the actual N (divider) value.
Update the offset of the N value to fix the calculation of the PLL rate.
Fixes: 28b9fcd016126e ("clk: meson8b: Add support for Meson8b clocks") Reported-by: Jianxin Pan <jianxin.pan@amlogic.com> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Link: https://lkml.kernel.org/r/20181202214220.7715-2-martin.blumenstingl@googlemail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
PXA25xx SoCs don't have a USB controller, so drop the node from the
common pxa2xx.dtsi base file. Both pxa27x and pxa3xx have a dedicated
node already anyway.
While at it, unify the names for the nodes across all pxa platforms.
Signed-off-by: Daniel Mack <daniel@zonque.org> Reported-by: Sergey Yanovich <ynvich@gmail.com> Link: https://patchwork.kernel.org/patch/8375421/ Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Sasha Levin <sashal@kernel.org>
mtd_oobavail() returns either mtd->oovabail or mtd->oobsize. Both
values are unsigned 32-bit entities, so there is no reason to pretend
returning a signed one.
Building a single target in an external module fails due to missing
.tmp_versions directory.
For example,
$ make -C /lib/modules/$(uname -r)/build M=$PWD foo.o
will fail in the following way:
CC [M] /home/masahiro/foo/foo.o
/bin/sh: 1: cannot create /home/masahiro/foo/.tmp_versions/foo.mod: Directory nonexistent
This is because $(cmd_crmodverdir) is executed only before building
/, %/, %.ko single targets of external modules. Create .tmp_versions
in the 'prepare' target.
During development of a serial console driver with a gcc 8.2.0
toolchain for RISC-V, the following modpost warning appeared:
----
WARNING: vmlinux.o(.data+0x19b10): Section mismatch in reference from the variable .LANCHOR1 to the function .init.text:sifive_serial_console_setup()
The variable .LANCHOR1 references
the function __init sifive_serial_console_setup()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
----
".LANCHOR1" is an ELF local symbol, automatically created by gcc's section
anchor generation code:
This was verified by compiling the kernel with -fno-section-anchors
and observing that the ".LANCHOR1" ELF local symbol disappeared, and
modpost no longer warned about the section mismatch. The serial
driver code idiom triggering the warning is standard Linux serial
driver practice that has a specific whitelist inclusion in modpost.c.
I'm neither a modpost nor an ELF expert, but naively, it doesn't seem
useful for modpost to report section mismatch warnings caused by ELF
local symbols by default. Local symbols have compiler-generated
names, and thus bypass modpost's whitelisting algorithm, which relies
on the presence of a non-autogenerated symbol name. This increases
the likelihood that false positive warnings will be generated (as in
the above case).
Thus, disable section mismatch reporting on ELF local symbols. The
rationale here is similar to that of commit 2e3a10a1551d ("ARM: avoid
ARM binutils leaking ELF local symbols") and of similar code already
present in modpost.c:
This third version of the patch implements a suggestion from Masahiro
Yamada <yamada.masahiro@socionext.com> to restructure the code as an
additional pattern matching step inside secref_whitelist(), and
further improves the patch description.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com> Signed-off-by: Paul Walmsley <paul@pwsan.com> Acked-by: Sam Ravnborg <sam@ravnborg.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Previously the SNMP TCPTIMEOUTS counter has inconsistent accounting:
1. It counts all SYN and SYN-ACK timeouts
2. It counts timeouts in other states except recurring timeouts and
timeouts after fast recovery or disorder state.
Such selective accounting makes analysis difficult and complicated. For
example the monitoring system needs to collect many other SNMP counters
to infer the total amount of timeout events. This patch makes TCPTIMEOUTS
counter simply counts all the retransmit timeout (SYN or data or FIN).
Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log