For each I/O request, blkback first maps the foreign pages for the
request to its local pages. If an allocation of a local page for the
mapping fails, it should unmap every mapping already made for the
request.
However, blkback's handling mechanism for the allocation failure does
not mark the remaining foreign pages as unmapped. Therefore, the unmap
function merely tries to unmap every valid grant page for the request,
including the pages not mapped due to the allocation failure. On a
system that fails the allocation frequently, this problem leads to
following kernel crash.
This commit fixes this problem by marking the grant pages of the given
request that didn't mapped due to the allocation failure as invalid.
Fixes: c6cc142dac52 ("xen-blkback: use balloon pages for all mappings") Reviewed-by: David Woodhouse <dwmw@amazon.de> Reviewed-by: Maximilian Heyne <mheyne@amazon.de> Reviewed-by: Paul Durrant <pdurrant@amazon.co.uk> Reviewed-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: SeongJae Park <sjpark@amazon.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an SMT capable system is not IPL'ed from the first CPU the setup of
the physical to logical CPU mapping is broken: the IPL core gets CPU
number 0, but then the next core gets CPU number 1. Correct would be
that all SMT threads of CPU 0 get the subsequent logical CPU numbers.
This is important since a lot of code (like e.g. the CPU topology
code) assumes that CPU maps are setup like this. If the mapping is
broken the system will not IPL due to broken topology masks:
[ 1.716341] BUG: arch topology broken
[ 1.716342] the SMT domain not a subset of the MC domain
[ 1.716343] BUG: arch topology broken
[ 1.716344] the MC domain not a subset of the BOOK domain
This scenario can usually not happen since LPARs are always IPL'ed
from CPU 0 and also re-IPL is intiated from CPU 0. However older
kernels did initiate re-IPL on an arbitrary CPU. If therefore a re-IPL
from an old kernel into a new kernel is initiated this may lead to
crash.
Fix this by setting up the physical to logical CPU mapping correctly.
Above Oops are due to the slab-out-of-bounds happened in do-while of
function layout_in_gaps indirectly called by ubifs_tnc_start_commit. In
function layout_in_gaps, there is a do-while loop placing index nodes
into the gaps created by obsolete index nodes in non-empty index LEBs
until rest index nodes can totally be placed into pre-allocated empty
LEBs. @c->gap_lebs points to a memory area(integer array) which records
LEB numbers used by 'in-the-gaps' method. Whenever a fitable index LEB
is found, corresponding lnum will be incrementally written into the
memory area pointed by @c->gap_lebs. The size
((@c->lst.idx_lebs + 1) * sizeof(int)) of memory area is allocated before
do-while loop and can not be changed in the loop. But @c->lst.idx_lebs
could be increased by function ubifs_change_lp (called by
layout_leb_in_gaps->ubifs_find_dirty_idx_leb->get_idx_gc_leb) during the
loop. So, sometimes oob happens when number of cycles in do-while loop
exceeds the original value of @c->lst.idx_lebs. See detail in
https://bugzilla.kernel.org/show_bug.cgi?id=204229.
This patch fixes oob in layout_in_gaps.
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 29572 Comm: kworker/1:4 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events rt6_probe_deferred
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Christoph Hellwig complained about the following soft lockup warning
when running scrub after generic/175 when preemption is disabled and
slub debugging is enabled:
If preemption is disabled, all metadata buffers needed to perform the
scrub are already in memory, and there are a lot of records to check,
it's possible that the scrub thread will run for an extended period of
time without sleeping for IO or any other reason. Then the watchdog
timer or the RCU stall timeout can trigger, producing the backtrace
above.
To fix this problem, call cond_resched() from the scrub thread so that
we back out to the scheduler whenever necessary.
Reported-by: Christoph Hellwig <hch@infradead.org> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current code doesn't limit the number of nested devices.
Nested devices would be handled recursively and this needs huge stack
memory. So, unlimited nested devices could make stack overflow.
This patch adds upper_level and lower_level, they are common variables
and represent maximum lower/upper depth.
When upper/lower device is attached or dettached,
{lower/upper}_level are updated. and if maximum depth is bigger than 8,
attach routine fails and returns -EMLINK.
In addition, this patch converts recursive routine of
netdev_walk_all_{lower/upper} to iterator routine.
Test commands:
ip link add dummy0 type dummy
ip link add link dummy0 name vlan1 type vlan id 1
ip link set vlan1 up
for i in {2..55}
do
let A=$i-1
ip link add vlan$i link vlan$A type vlan id $i
done
ip link del dummy0
Splat looks like:
[ 155.513226][ T908] BUG: KASAN: use-after-free in __unwind_start+0x71/0x850
[ 155.514162][ T908] Write of size 88 at addr ffff8880608a6cc0 by task ip/908
[ 155.515048][ T908]
[ 155.515333][ T908] CPU: 0 PID: 908 Comm: ip Not tainted 5.4.0-rc3+ #96
[ 155.516147][ T908] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 155.517233][ T908] Call Trace:
[ 155.517627][ T908]
[ 155.517918][ T908] Allocated by task 0:
[ 155.518412][ T908] (stack is not available)
[ 155.518955][ T908]
[ 155.519228][ T908] Freed by task 0:
[ 155.519885][ T908] (stack is not available)
[ 155.520452][ T908]
[ 155.520729][ T908] The buggy address belongs to the object at ffff8880608a6ac0
[ 155.520729][ T908] which belongs to the cache names_cache of size 4096
[ 155.522387][ T908] The buggy address is located 512 bytes inside of
[ 155.522387][ T908] 4096-byte region [ffff8880608a6ac0, ffff8880608a7ac0)
[ 155.523920][ T908] The buggy address belongs to the page:
[ 155.524552][ T908] page:ffffea0001822800 refcount:1 mapcount:0 mapping:ffff88806c657cc0 index:0x0 compound_mapcount:0
[ 155.525836][ T908] flags: 0x100000000010200(slab|head)
[ 155.526445][ T908] raw: 0100000000010200ffffea0001813808ffffea0001a26c08ffff88806c657cc0
[ 155.527424][ T908] raw: 0000000000000000000000000007000700000001ffffffff0000000000000000
[ 155.528429][ T908] page dumped because: kasan: bad access detected
[ 155.529158][ T908]
[ 155.529410][ T908] Memory state around the buggy address:
[ 155.530060][ T908] ffff8880608a6b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 155.530971][ T908] ffff8880608a6c00: fb fb fb fb fb f1 f1 f1 f1 00 f2 f2 f2 f3 f3 f3
[ 155.531889][ T908] >ffff8880608a6c80: f3 fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 155.532806][ T908] ^
[ 155.533509][ T908] ffff8880608a6d00: fb fb fb fb fb fb fb fb fb f1 f1 f1 f1 00 00 00
[ 155.534436][ T908] ffff8880608a6d80: f2 f3 f3 f3 f3 fb fb fb 00 00 00 00 00 00 00 00
[ ... ]
Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
read to 0xffff888120425770 of 4 bytes by task 7254 on cpu 1:
tcp_stream_is_readable net/ipv4/tcp.c:480 [inline]
tcp_poll+0x204/0x6b0 net/ipv4/tcp.c:554
sock_poll+0xed/0x250 net/socket.c:1256
vfs_poll include/linux/poll.h:90 [inline]
ep_item_poll.isra.0+0x90/0x190 fs/eventpoll.c:892
ep_send_events_proc+0x113/0x5c0 fs/eventpoll.c:1749
ep_scan_ready_list.constprop.0+0x189/0x500 fs/eventpoll.c:704
ep_send_events fs/eventpoll.c:1793 [inline]
ep_poll+0xe3/0x900 fs/eventpoll.c:1930
do_epoll_wait+0x162/0x180 fs/eventpoll.c:2294
__do_sys_epoll_pwait fs/eventpoll.c:2325 [inline]
__se_sys_epoll_pwait fs/eventpoll.c:2311 [inline]
__x64_sys_epoll_pwait+0xcd/0x170 fs/eventpoll.c:2311
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 7254 Comm: syz-fuzzer Not tainted 5.3.0+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If an ICMP packet comes in on the UDP socket backing an AF_RXRPC socket as
the UDP socket is being shut down, rxrpc_error_report() may get called to
deal with it after sk_user_data on the UDP socket has been cleared, leading
to a NULL pointer access when this local endpoint record gets accessed.
Fix this by just returning immediately if sk_user_data was NULL.
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both") Reported-by: syzbot+611164843bd48cc2190c@syzkaller.appspotmail.com Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On a 2-socket Power9 system with 32 cores/128 threads (SMT4) and 1TB
of memory running the following guest configs:
guest A:
- 224GB of memory
- 56 VCPUs (sockets=1,cores=28,threads=2), where:
VCPUs 0-1 are pinned to CPUs 0-3,
VCPUs 2-3 are pinned to CPUs 4-7,
...
VCPUs 54-55 are pinned to CPUs 108-111
guest B:
- 4GB of memory
- 4 VCPUs (sockets=1,cores=4,threads=1)
with the following workloads (with KSM and THP enabled in all):
the below soft-lockup traces were observed after an hour or so and
persisted until the host was reset (this was found to be reliably
reproducible for this configuration, for kernels 4.15, 4.18, 5.0,
and 5.3-rc5):
[ 1253.183290] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1253.183319] rcu: 124-....: (5250 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=1941
[ 1256.287426] watchdog: BUG: soft lockup - CPU#105 stuck for 23s! [CPU 52/KVM:19709]
[ 1264.075773] watchdog: BUG: soft lockup - CPU#24 stuck for 23s! [worker:19913]
[ 1264.079769] watchdog: BUG: soft lockup - CPU#31 stuck for 23s! [worker:20331]
[ 1264.095770] watchdog: BUG: soft lockup - CPU#45 stuck for 23s! [worker:20338]
[ 1264.131773] watchdog: BUG: soft lockup - CPU#64 stuck for 23s! [avocado:19525]
[ 1280.408480] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791]
[ 1316.198012] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1316.198032] rcu: 124-....: (21003 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=8243
[ 1340.411024] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791]
[ 1379.212609] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1379.212629] rcu: 124-....: (36756 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=14714
[ 1404.413615] watchdog: BUG: soft lockup - CPU#124 stuck for 22s! [ksmd:791]
[ 1442.227095] rcu: INFO: rcu_sched self-detected stall on CPU
[ 1442.227115] rcu: 124-....: (52509 ticks this GP) idle=10a/1/0x4000000000000002 softirq=5408/5408 fqs=21403
[ 1455.111787] INFO: task worker:19907 blocked for more than 120 seconds.
[ 1455.111822] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.111833] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.111884] INFO: task worker:19908 blocked for more than 120 seconds.
[ 1455.111905] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.111925] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.111966] INFO: task worker:20328 blocked for more than 120 seconds.
[ 1455.111986] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.111998] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.112048] INFO: task worker:20330 blocked for more than 120 seconds.
[ 1455.112068] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.112097] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.112138] INFO: task worker:20332 blocked for more than 120 seconds.
[ 1455.112159] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.112179] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.112210] INFO: task worker:20333 blocked for more than 120 seconds.
[ 1455.112231] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.112242] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.112282] INFO: task worker:20335 blocked for more than 120 seconds.
[ 1455.112303] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
[ 1455.112332] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1455.112372] INFO: task worker:20336 blocked for more than 120 seconds.
[ 1455.112392] Tainted: G L 5.3.0-rc5-mdr-vanilla+ #1
CPUs 45, 24, and 124 are stuck on spin locks, likely held by
CPUs 105 and 31.
CPUs 105 and 31 are stuck in smp_call_function_many(), waiting on
target CPU 42. For instance:
It was subsequently found that ipi_message[PPC_MSG_CALL_FUNCTION]
was set for CPU 42 by at least 1 of the CPUs waiting in
smp_call_function_many(), but somehow the corresponding
call_single_queue entries were never processed by CPU 42, causing the
callers to spin in csd_lock_wait() indefinitely.
Nick Piggin suggested something similar to the following sequence as
a possible explanation (interleaving of CALL_FUNCTION/RESCHEDULE
IPI messages seems to be most common, but any mix of CALL_FUNCTION and
!CALL_FUNCTION messages could trigger it):
CPU
X: smp_muxed_ipi_set_message():
X: smp_mb()
X: message[RESCHEDULE] = 1
X: doorbell_global_ipi(42):
X: kvmppc_set_host_ipi(42, 1)
X: ppc_msgsnd_sync()/smp_mb()
X: ppc_msgsnd() -> 42
42: doorbell_exception(): // from CPU X
42: ppc_msgsync()
105: smp_muxed_ipi_set_message():
105: smb_mb()
// STORE DEFERRED DUE TO RE-ORDERING
--105: message[CALL_FUNCTION] = 1
| 105: doorbell_global_ipi(42):
| 105: kvmppc_set_host_ipi(42, 1)
| 42: kvmppc_set_host_ipi(42, 0)
| 42: smp_ipi_demux_relaxed()
| 42: // returns to executing guest
| // RE-ORDERED STORE COMPLETES
->105: message[CALL_FUNCTION] = 1
105: ppc_msgsnd_sync()/smp_mb()
105: ppc_msgsnd() -> 42
42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored
105: // hangs waiting on 42 to process messages/call_single_queue
This can be prevented with an smp_mb() at the beginning of
kvmppc_set_host_ipi(), such that stores to message[<type>] (or other
state indicated by the host_ipi flag) are ordered vs. the store to
to host_ipi.
However, doing so might still allow for the following scenario (not
yet observed):
CPU
X: smp_muxed_ipi_set_message():
X: smp_mb()
X: message[RESCHEDULE] = 1
X: doorbell_global_ipi(42):
X: kvmppc_set_host_ipi(42, 1)
X: ppc_msgsnd_sync()/smp_mb()
X: ppc_msgsnd() -> 42
42: doorbell_exception(): // from CPU X
42: ppc_msgsync()
// STORE DEFERRED DUE TO RE-ORDERING
-- 42: kvmppc_set_host_ipi(42, 0)
| 42: smp_ipi_demux_relaxed()
| 105: smp_muxed_ipi_set_message():
| 105: smb_mb()
| 105: message[CALL_FUNCTION] = 1
| 105: doorbell_global_ipi(42):
| 105: kvmppc_set_host_ipi(42, 1)
| // RE-ORDERED STORE COMPLETES
-> 42: kvmppc_set_host_ipi(42, 0)
42: // returns to executing guest
105: ppc_msgsnd_sync()/smp_mb()
105: ppc_msgsnd() -> 42
42: local_paca->kvm_hstate.host_ipi == 0 // IPI ignored
105: // hangs waiting on 42 to process messages/call_single_queue
Fixing this scenario would require an smp_mb() *after* clearing
host_ipi flag in kvmppc_set_host_ipi() to order the store vs.
subsequent processing of IPI messages.
To handle both cases, this patch splits kvmppc_set_host_ipi() into
separate set/clear functions, where we execute smp_mb() prior to
setting host_ipi flag, and after clearing host_ipi flag. These
functions pair with each other to synchronize the sender and receiver
sides.
With that change in place the above workload ran for 20 hours without
triggering any lock-ups.
Fixes: 755563bc79c7 ("powerpc/powernv: Fixes for hypervisor doorbell handling") # v4.0 Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com> Acked-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20190911223155.16045-1-mdroth@linux.vnet.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
This exercises kernel code path that deal with addresses that have
a limited lifetime.
Without previous fix, this triggers following crash on net-next:
BUG: KASAN: null-ptr-deref in check_lifetime+0x403/0x670
Read of size 8 at addr 0000000000000010 by task kworker [..]
Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While developing KASAN for 64-bit book3s, I hit the following stack
over-read.
It occurs because the hypercall to put characters onto the terminal
takes 2 longs (128 bits/16 bytes) of characters at a time, and so
hvc_put_chars() would unconditionally copy 16 bytes from the argument
buffer, regardless of supplied length. However, udbg_hvc_putc() can
call hvc_put_chars() with a single-byte buffer, leading to the error.
==================================================================
BUG: KASAN: stack-out-of-bounds in hvc_put_chars+0xdc/0x110
Read of size 8 at addr c0000000023e7a90 by task swapper/0
Fix the breakage resulting in the stacktrace below, due to tx queue
being full when trying to send an up-reply. txmsg->seqno is -1 in this
case leading to a corruption of the mstb object by
If we cannot allocate an ELS middlepath request, simply fail instead of
trying to delay and then reallocate. This delay logic is causing soft
lockup messages:
Currently, block device size in not updated on second and further open
for block devices where partition scan is disabled. This is particularly
annoying for example for DVD drives as that means block device size does
not get updated once the media is inserted into a drive if the device is
already open when inserting the media. This is actually always the case
for example when pktcdvd is in use.
Fix the problem by revalidating block device size on every open even for
devices with partition scan disabled.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike FICLONE, all of those take a pointer argument; they do need
compat_ptr() applied to arg.
Fixes: d79bdd52d8be ("vfs: wire up compat ioctl for CLONE/CLONE_RANGE") Fixes: 54dbc1517237 ("vfs: hoist the btrfs deduplication ioctl to the vfs") Fixes: ceac204e1da9 ("fs: make fiemap work from compat_ioctl") Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the commit 677fe555cbfb ("serial: imx: Fix recursive locking bug")
has mentioned the uart driver might cause recursive locking between
normal printing and the kernel debugging facilities (e.g. sysrq and
oops). In the commit it gave out suggestion for fixing recursive
locking issue: "The solution is to avoid locking in the sysrq case
and trylock in the oops_in_progress case."
This patch follows the suggestion (also used the exactly same code with
other serial drivers, e.g. amba-pl011.c) to fix the recursive locking
issue, this can avoid stuck caused by deadlock and print out log for
sysrq and oops.
Fixes: 04896a77a97b ("msm_serial: serial driver for MSM7K onboard serial peripheral.") Signed-off-by: Leo Yan <leo.yan@linaro.org> Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Link: https://lore.kernel.org/r/20191127141544.4277-2-leo.yan@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_otg bus needs to get initialize from the u-boot to be configured
to used as power source to SBC or usb otg port will get configured
as host device. Right now this support is missing in the u-boot and
phy driver so to avoid power failed warning, we would disable this
feature until proper fix is found.
In af9005_identify_state when returning -EIO the allocated buffer should
be released. Replace the "return -EIO" with assignment into ret and move
deb_info() under a check.
Fixes: af4e067e1dcf ("V4L/DVB (5625): Add support for the AF9005 demodulator from Afatech") Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB regulator was removed for AB8500 in
commit 41a06aa738ad ("regulator: ab8500: Remove USB regulator").
It was then added for AB8505 in
commit 547f384f33db ("regulator: ab8500: add support for ab8505").
However, there was never an entry added for it in
ab8505_regulator_match. This causes all regulators after it
to be initialized with the wrong device tree data, eventually
leading to an out-of-bounds array read.
Given that it is not used anywhere in the kernel, it seems
likely that similar arguments against supporting it exist for
AB8505 (it is controlled by hardware).
Therefore, simply remove it like for AB8500 instead of adding
an entry in ab8505_regulator_match.
Fixes: 547f384f33db ("regulator: ab8500: add support for ab8505") Cc: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Stephan Gerhold <stephan@gerhold.net> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20191106173125.14496-1-stephan@gerhold.net Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An earlier commit hard coded a return 0 to function flexcop_usb_i2c_req
even though the an -EIO was intended to be returned in the case where
ret != buflen. Fix this by replacing the return 0 with the return of
ret to return the error return code.
Addresses-Coverity: ("Unused value")
Fixes: b430eaba0be5 ("[media] flexcop-usb: don't use stack for DMA") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the implementation of hci_connect_le_scan() when conn is added via
hci_conn_add(), if hci_explicit_conn_params_set() fails the allocated
memory for conn is leaked. Use hci_conn_del() to release it.
We used to take a lock in amp_physical_cfm() but then we moved it to
the caller function. Unfortunately the unlock on this error path was
overlooked so it leads to a double unlock.
Fixes: a514b17fab51 ("Bluetooth: Refactor locking in amp_physical_cfm") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONNECT X300 uses the PMC clock for on-board components and gets
stuck during boot if the clock is disabled. Therefore, add this
device to the critical systems list.
Tested on CONNECT X300.
Fixes: 648e921888ad ("clk: x86: Stop marking clocks as CLK_IS_CRITICAL") Signed-off-by: Michael Haener <michael.haener@siemens.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5b094d6dac04 ("xfs: fix multi-AG deadlock in xfs_bunmapi") added
a check in __xfs_bunmapi() to stop early if we would touch multiple AGs
in the wrong order. However, this check isn't applicable for realtime
files. In most cases, it just makes us do unnecessary commits. However,
without the fix from the previous commit ("xfs: fix realtime file data
space leak"), if the last and second-to-last extents also happen to have
different "AG numbers", then the break actually causes __xfs_bunmapi()
to return without making any progress, which sends
xfs_itruncate_extents_flags() into an infinite loop.
Fixes: 5b094d6dac04 ("xfs: fix multi-AG deadlock in xfs_bunmapi") Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 0f27cff8597d ("ACPI: sysfs: Make ACPI GPE mask kernel
parameter cover all GPEs") says:
"Use a bitmap of size 0xFF instead of a u64 for the GPE mask so 256
GPEs can be masked"
But the masking of GPE 0xFF it not supported and the check condition
"gpe > ACPI_MASKABLE_GPE_MAX" is not valid because the type of gpe is
u8.
So modify the macro ACPI_MASKABLE_GPE_MAX to 0x100, and drop the "gpe >
ACPI_MASKABLE_GPE_MAX" check. In addition, update the docs "Format" for
acpi_mask_gpe parameter.
Fixes: 0f27cff8597d ("ACPI: sysfs: Make ACPI GPE mask kernel parameter cover all GPEs") Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
[ rjw: Use u16 as gpe data type in acpi_gpe_apply_masked_gpes() ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 52cf93e63ee6 ("HID: i2c-hid: Don't reset device upon system
resume") fixes many touchpads and touchscreens, however ALPS touchpads
start to trigger IRQ storm after system resume.
Since it's total silence from ALPS, let's bring the old behavior back
to ALPS touchpads.
When running an nfs stress test, I see quite a few cached replies that
don't match up with the actual request. The first comment in
replay_matches_cache() makes sense, but the code doesn't seem to
match... fix it.
This isn't exactly a bugfix, as the server isn't required to catch every
case of a false retry. So, we may as well do this, but if this is
fixing a problem then that suggests there's a client bug.
Fixes: 53da6a53e1d4 ("nfsd4: catch some false session retries") Signed-off-by: Scott Mayhew <smayhew@redhat.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ftrace_profile->counter is unsigned long and
do_div truncates it to 32 bits, which means it can test
non-zero and be truncated to zero for division.
Fix this issue by using div64_ul() instead.
Link: http://lkml.kernel.org/r/20200103030248.14516-1-wenyang@linux.alibaba.com Cc: stable@vger.kernel.org Fixes: e330b3bcd8319 ("tracing: Show sample std dev in function profiling") Fixes: 34886c8bc590f ("tracing: add average time in function to function profiler") Signed-off-by: Wen Yang <wenyang@linux.alibaba.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ARMv8 64-bit architecture supports execute-only user permissions by
clearing the PTE_USER and PTE_UXN bits, practically making it a mostly
privileged mapping but from which user running at EL0 can still execute.
The downside, however, is that the kernel at EL1 inadvertently reading
such mapping would not trip over the PAN (privileged access never)
protection.
Revert the relevant bits from commit cab15ce604e5 ("arm64: Introduce
execute-only page access permissions") so that PROT_EXEC implies
PROT_READ (and therefore PTE_USER) until the architecture gains proper
support for execute-only user mappings.
Currently, when global init and all threads in its thread-group have exited
we panic via:
do_exit()
-> exit_notify()
-> forget_original_parent()
-> find_child_reaper()
This makes it hard to extract a useable coredump for global init from a
kernel crashdump because by the time we panic exit_mm() will have already
released global init's mm.
This patch moves the panic futher up before exit_mm() is called. As was the
case previously, we only panic when global init and all its threads in the
thread-group have exited.
The return from pnp_irq is an unsigned integer type resource_size_t
and hence the error check for a positive non-error code is always
going to be true. A check for a non-failure return from pnp_irq
should in fact be for (resource_size_t)-1 rather than >= 0.
Addresses-Coverity: ("Unsigned compared against 0") Fixes: a9824c868a2c ("[ALSA] Add CS4232 PnP BIOS support") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20191122131354.58042-1-colin.king@canonical.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
aa_xattrs_match() is unfortunately calling vfs_getxattr_alloc() from a
context protected by an rcu_read_lock. This can not be done as
vfs_getxattr_alloc() may sleep regardles of the gfp_t value being
passed to it.
Fix this by breaking the rcu_read_lock on the policy search when the
xattr match feature is requested and restarting the search if a policy
changes occur.
Fixes: 8e51f9087f40 ("apparmor: Add support for attaching profiles via xattr, presence and value") Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com> Reported-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: John Johansen <john.johansen@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least on PA-RISC and s390 synthetic histogram triggers are failing
selftests because trace_event_raw_event_synth() always writes a 64 bit
values, but the reader expects a field->size sized value. On little endian
machines this doesn't hurt, but on big endian this makes the reader always
read zero values.
Link: http://lore.kernel.org/linux-trace-devel/20191218074427.96184-4-svens@linux.ibm.com Cc: stable@vger.kernel.org Fixes: 4b147936fa509 ("tracing: Add support for 'synthetic' events") Acked-by: Tom Zanussi <tom.zanussi@linux.intel.com> Signed-off-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The compare functions of the histogram code would be specific for the size
of the value being compared (byte, short, int, long long). It would
reference the value from the array via the type of the compare, but the
value was stored in a 64 bit number. This is fine for little endian
machines, but for big endian machines, it would end up comparing zeros or
all ones (depending on the sign) for anything but 64 bit numbers.
To fix this, first derference the value as a u64 then convert it to the type
being compared.
Link: http://lkml.kernel.org/r/20191211103557.7bed6928@gandalf.local.home Cc: stable@vger.kernel.org Fixes: 08d43a5fa063e ("tracing: Add lock-free tracing_map") Acked-by: Tom Zanussi <zanussi@kernel.org> Reported-by: Sven Schnelle <svens@stackframe.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When failing in the allocation of filter_item, process_system_preds()
goes to fail_mem, where the allocated filter is freed.
However, this leads to memory leak of filter->filter_string and
filter->prog, which is allocated before and in process_preds().
This bug has been detected by kmemleak as well.
This gives a circular dependency deadlock between trace_types_lock and
event_mutex. To fix this invert the usage of trace_types_lock and
event_mutex in trace_options_core_write(). This keeps the sequence of
lock usage consistent.
gpiolib has a corner case with open drain outputs that are emulated.
When such outputs are outputting a logic 1, emulation will set the
hardware to input mode, which will cause gpiod_get_direction() to
report that it is in input mode. This is different from the behaviour
with a true open-drain output.
Unify the semantics here.
Cc: <stable@vger.kernel.org> Suggested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c40368 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c403683 ("libata: add extra internal command") Cc: stable@vger.kernel.org Tested-by: Pali Rohár <pali.rohar@gmail.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing export of ata_qc_get_active(), as per Pali.
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms") Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae241 ("ata: ahci_brcm: Recover from failures to identify devices") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: eba68f829794 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's") Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 6bb86fefa086faba7b60bb452300b76a47cde1a5
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dmaengine_desc_set_reuse() allocates a struct dma_slave_caps on the
stack, populates it using dma_get_slave_caps() and then accesses one
of its members.
However dma_get_slave_caps() may fail and this isn't accounted for,
leading to a legitimate warning of gcc-4.9 (but not newer versions):
In file included from drivers/spi/spi-bcm2835.c:19:0:
drivers/spi/spi-bcm2835.c: In function 'dmaengine_desc_set_reuse':
>> include/linux/dmaengine.h:1370:10: warning: 'caps.descriptor_reuse' is used uninitialized in this function [-Wuninitialized]
if (caps.descriptor_reuse) {
Fix it, thereby also silencing the gcc-4.9 warning.
The issue has been present for 4 years but surfaces only now that
the first caller of dmaengine_desc_set_reuse() has been added in
spi-bcm2835.c. Another user of reusable DMA descriptors has existed
for a while in pxa_camera.c, but it sets the DMA_CTRL_REUSE flag
directly instead of calling dmaengine_desc_set_reuse(). Nevertheless,
tag this commit for stable in case there are out-of-tree users.
The ram_core.c routines treat przs as circular buffers. When writing a
new crash dump, the old buffer needs to be cleared so that the new dump
doesn't end up in the wrong place (i.e. at the end).
The solution to this problem is to reset the circular buffer state before
writing a new Oops dump.
This is because the status is not set if the page is already on the
target node, but move_pages() should return valid status as long as it
succeeds. The valid status may be errno or node id.
We can't simply initialize status array to zero since the pages may be
not on node 0. Fix it by updating status with node id which the page is
already on.
Link: http://lkml.kernel.org/r/1575584353-125392-1-git-send-email-yang.shi@linux.alibaba.com Fixes: a49bd4d71637 ("mm, numa: rework do_pages_move") Signed-off-by: Yang Shi <yang.shi@linux.alibaba.com> Reported-by: Felix Abecassis <fabecassis@nvidia.com> Tested-by: Felix Abecassis <fabecassis@nvidia.com> Suggested-by: Michal Hocko <mhocko@suse.com> Reviewed-by: John Hubbard <jhubbard@nvidia.com> Acked-by: Christoph Lameter <cl@linux.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: <stable@vger.kernel.org> [4.17+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cred_jar kmem_cache is already memcg accounted in the current kernel
but cred->security is not. Account cred->security to kmemcg.
Recently we saw high root slab usage on our production and on further
inspection, we found a buggy application leaking processes. Though that
buggy application was contained within its memcg but we observe much
more system memory overhead, couple of GiBs, during that period. This
overhead can adversely impact the isolation on the system.
One source of high overhead we found was cred->security objects, which
have a lifetime of at least the life of the process which allocated
them.
Link: http://lkml.kernel.org/r/20191205223721.40034-1-shakeelb@google.com Signed-off-by: Shakeel Butt <shakeelb@google.com> Acked-by: Chris Down <chris@chrisdown.name> Reviewed-by: Roman Gushchin <guro@fb.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When zspage is migrated to the other zone, the zone page state should be
updated as well, otherwise the NR_ZSPAGE for each zone shows wrong
counts including proc/zoneinfo in practice.
Link: http://lkml.kernel.org/r/1575434841-48009-1-git-send-email-chanho.min@lge.com Fixes: 91537fee0013 ("mm: add NR_ZSMALLOC to vmstat") Signed-off-by: Chanho Min <chanho.min@lge.com> Signed-off-by: Jinsuk Choi <jjinsuk.choi@lge.com> Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Acked-by: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org> [4.9+] Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently wait_event_interruptible_timeout is called in cec_thread_func()
when adap->transmitting is set. But if the adapter is unconfigured
while transmitting, then adap->transmitting is set to NULL. But the
hardware is still actually transmitting the message, and that's
indicated by adap->transmit_in_progress and we should wait until that
is finished or times out before transmitting new messages.
As the original commit says: adap->transmitting is the userspace view,
adap->transmit_in_progress reflects the hardware state.
However, if adap->transmitting is NULL and adap->transmit_in_progress
is true, then wait_event_interruptible is called (no timeout), which
can get stuck indefinitely if the CEC driver is flaky and never marks
the transmit-in-progress as 'done'.
So test against transmit_in_progress when deciding whether to use
the timeout variant or not, instead of testing against adap->transmitting.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Fixes: 32804fcb612b ("media: cec: keep track of outstanding transmits") Cc: <stable@vger.kernel.org> # for v4.19 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARN if transmit_queue_sz is 0 but do not decrement it.
The CEC adapter will become unresponsive if it goes below
0 since then it thinks there are 4 billion messages in the
queue.
Obviously this should not happen, but a driver bug could
cause this.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v4.12 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some messages are allowed to be a broadcast message in CEC 2.0
only, and should be ignored by CEC 1.4 devices.
Unfortunately, the check was wrong, causing such messages to be
marked as invalid under CEC 2.0.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v4.10 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The periodic PING command could interfere with the result of
a CEC transmit, causing a lost cec_transmit_attempt_done()
call.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Cc: <stable@vger.kernel.org> # for v4.10 and up Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declaring __current_thread_info as a global register variable has the
effect of preventing GCC from saving & restoring its value in cases
where the ABI would typically do so.
To quote GCC documentation:
> If the register is a call-saved register, call ABI is affected: the
> register will not be restored in function epilogue sequences after the
> variable has been assigned. Therefore, functions cannot safely return
> to callers that assume standard ABI.
When our position independent VDSO is built for the n32 or n64 ABIs all
functions it exposes should be preserving the value of $gp/$28 for their
caller, but in the presence of the __current_thread_info global register
variable GCC stops doing so & simply clobbers $gp/$28 when calculating
the address of the GOT.
In cases where the VDSO returns success this problem will typically be
masked by the caller in libc returning & restoring $gp/$28 itself, but
that is by no means guaranteed. In cases where the VDSO returns an error
libc will typically contain a fallback path which will now fail
(typically with a bad memory access) if it attempts anything which
relies upon the value of $gp/$28 - eg. accessing anything via the GOT.
One fix for this would be to move the declaration of
__current_thread_info inside the current_thread_info() function,
demoting it from global register variable to local register variable &
avoiding inadvertently creating a non-standard calling ABI for the VDSO.
Unfortunately this causes issues for clang, which doesn't support local
register variables as pointed out by commit fe92da0f355e ("MIPS: Changed
current_thread_info() to an equivalent supported by both clang and GCC")
which introduced the global register variable before we had a VDSO to
worry about.
Instead, fix this by continuing to use the global register variable for
the kernel proper but declare __current_thread_info as a simple extern
variable when building the VDSO. It should never be referenced, and will
cause a link error if it is. This resolves the calling convention issue
for the VDSO without having any impact upon the build of the kernel
itself for either clang or gcc.
Signed-off-by: Paul Burton <paulburton@kernel.org> Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Reported-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com> Tested-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Christian Brauner <christian.brauner@canonical.com> Cc: Vincenzo Frascino <vincenzo.frascino@arm.com> Cc: <stable@vger.kernel.org> # v4.4+ Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the HDMI unbinds drm_connector_cleanup() and drm_encoder_cleanup()
are called. This also happens when the connector and the encoder are
destroyed. This double call triggers a NULL pointer exception.
The patch fixes this by removing the cleanup calls in the unbind
function.
Recently we found the headset-mic on the Dell Dock WD19 doesn't work
anymore after s3 (s2i or deep), this problem could be workarounded by
closing (pcm_close) the app and then reopening (pcm_open) the app, so
this bug is not easy to be detected by users.
When problem happens, retire_capture_urb() could still be called
periodically, but the size of captured data is always 0, it could be
a firmware bug on the dock. Anyway I found after resuming, the
snd_usb_pcm_prepare() will be called, and if we forcibly run
set_format() to set the interface and its endpoint, the capture
size will be normal again. This problem and workaound also apply to
playback.
To fix it in the kernel, add a quirk to let set_format() run
forcibly once after resume.
Make sure to check the return value of usb_altnum_to_altsetting() to
avoid dereferencing a NULL pointer when the requested alternate settings
is missing.
The format altsetting number may come from a quirk table and there does
not seem to be any other validation of it (the corresponding index is
checked however).
Jia-Ju Bai reported a possible sleep-in-atomic scenario in the ice1724
driver with Infrasonic Quartet support code: namely, ice->set_rate
callback gets called inside ice->reg_lock spinlock, while the callback
in quartet.c holds ice->gpio_mutex.
This patch fixes the invalid call: it simply moves the calls of
ice->set_rate and ice->set_mclk callbacks outside the spinlock.
On Big Endian architectures, u16 port value was extracted from the wrong
parts of u32 sreg_port, just like commit 10596608c4d62 ("netfilter:
nf_tables: fix mismatch in big-endian system") describes.
When assiging and testing taskstats in taskstats_exit() there's a race
when setting up and reading sig->stats when a thread-group with more
than one thread exits:
write to 0xffff8881157bbe10 of 8 bytes by task 7951 on cpu 0:
taskstats_tgid_alloc kernel/taskstats.c:567 [inline]
taskstats_exit+0x6b7/0x717 kernel/taskstats.c:596
do_exit+0x2c2/0x18e0 kernel/exit.c:864
do_group_exit+0xb4/0x1c0 kernel/exit.c:983
get_signal+0x2a2/0x1320 kernel/signal.c:2734
do_signal+0x3b/0xc00 arch/x86/kernel/signal.c:815
exit_to_usermode_loop+0x250/0x2c0 arch/x86/entry/common.c:159
prepare_exit_to_usermode arch/x86/entry/common.c:194 [inline]
syscall_return_slowpath arch/x86/entry/common.c:274 [inline]
do_syscall_64+0x2d7/0x2f0 arch/x86/entry/common.c:299
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8881157bbe10 of 8 bytes by task 7949 on cpu 1:
taskstats_tgid_alloc kernel/taskstats.c:559 [inline]
taskstats_exit+0xb2/0x717 kernel/taskstats.c:596
do_exit+0x2c2/0x18e0 kernel/exit.c:864
do_group_exit+0xb4/0x1c0 kernel/exit.c:983
__do_sys_exit_group kernel/exit.c:994 [inline]
__se_sys_exit_group kernel/exit.c:992 [inline]
__x64_sys_exit_group+0x2e/0x30 kernel/exit.c:992
do_syscall_64+0xcf/0x2f0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix this by using smp_load_acquire() and smp_store_release().
Reported-by: syzbot+c5d03165a1bd1dead0c1@syzkaller.appspotmail.com Fixes: 34ec12349c8a ("taskstats: cleanup ->signal->stats allocation") Cc: stable@vger.kernel.org Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com> Acked-by: Marco Elver <elver@google.com> Reviewed-by: Will Deacon <will@kernel.org> Reviewed-by: Andrea Parri <parri.andrea@gmail.com> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Link: https://lore.kernel.org/r/20191009114809.8643-1-christian.brauner@ubuntu.com Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot (via KASAN) reports a use-after-free in the error path of
xlog_alloc_log(). Specifically, the iclog freeing loop doesn't
handle the case of a fully initialized ->l_iclog linked list.
Instead, it assumes that the list is partially constructed and NULL
terminated.
This bug manifested because there was no possible error scenario
after iclog list setup when the original code was added. Subsequent
code and associated error conditions were added some time later,
while the original error handling code was never updated. Fix up the
error loop to terminate either on a NULL iclog or reaching the end
of the list.
Reported-by: syzbot+c732f8644185de340492@syzkaller.appspotmail.com Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The auto-parser assigns the bass speaker to DAC3 (NID 0x06) which
is without the volume control. I do not see a reason to use DAC2,
because the shared output to all speakers produces the sufficient
and well balanced sound. The stereo support is enough for this
purpose (laptop).
ASUS reported that there's an bass speaker in addition to internal
speaker and it uses DAC 0x02. It was not enabled in the commit 436e25505f34 ("ALSA: hda/realtek - Enable internal speaker of ASUS
UX431FLC") which only enables the amplifier and the front speaker.
This commit enables the bass speaker on top of the aforementioned
work to improve the acoustic experience.
Fixes: 436e25505f34 ("ALSA: hda/realtek - Enable internal speaker of ASUS UX431FLC") Signed-off-by: Chris Chiu <chiu@endlessm.com> Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20191230031118.95076-1-chiu@endlessm.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
When looking for a bit by number we make use of the cached result from the
preceding lookup to speed up operation. Firstly we check if the requested
pfn is within the cached zone and if not lookup the new zone. We then
check if the offset for that pfn falls within the existing cached node.
This happens regardless of whether the node is within the zone we are
now scanning. With certain memory layouts it is possible for this to
false trigger creating a temporary alias for the pfn to a different bit.
This leads the hibernation code to free memory which it was never allocated
with the expected fallout.
Ensure the zone we are scanning matches the cached zone before considering
the cached node.
Deep thanks go to Andrea for many, many, many hours of hacking and testing
that went into cornering this bug.
Reported-by: Andrea Righi <andrea.righi@canonical.com> Tested-by: Andrea Righi <andrea.righi@canonical.com> Signed-off-by: Andy Whitcroft <apw@canonical.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_XEN_BALLOON_MEMORY_HOTPLUG is not defined
reserve_additional_memory() will set balloon_stats.target_pages to a
wrong value in case there are still some ballooned pages allocated via
alloc_xenballooned_pages().
This will result in balloon_process() no longer be triggered when
ballooned pages are freed in batches.
Reported-by: Nicholas Tsirakis <niko.tsirakis@gmail.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Objects allocated by xen_blkif_alloc come from the 'blkif_cache' kmem
cache. This cache is destoyed when xen-blkif is unloaded so it is
necessary to wait for the deferred free routine used for such objects to
complete. This necessity was missed in commit 14855954f636 "xen-blkback:
allow module to be cleanly unloaded". This patch fixes the problem by
taking/releasing extra module references in xen_blkif_alloc/free()
respectively.
Signed-off-by: Paul Durrant <pdurrant@amazon.com> Reviewed-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The s390 CPU Measurement sampling facility has an overflow condition
which fires when all entries in a SBD are used.
The measurement alert interrupt is triggered and reads out all samples
in this SDB. It then tests the successor SDB, if this SBD is not full,
the interrupt handler does not read any samples at all from this SDB
The design waits for the hardware to fill this SBD and then trigger
another meassurement alert interrupt.
This scheme works nicely until
an perf_event_overflow() function call discards the sample due to
a too high sampling rate.
The interrupt handler has logic to read out a partially filled SDB
when the perf event overflow condition in linux common code is met.
This causes the CPUM sampling measurement hardware and the PMU
device driver to operate on the same SBD's trailer entry.
This should not happen.
This can be seen here using this trace:
cpumsf_pmu_add: tear:0xb5286000
hw_perf_event_update: sdbt 0xb5286000 full 1 over 0 flush_all:0
hw_perf_event_update: sdbt 0xb5286008 full 0 over 0 flush_all:0
above shows 1. interrupt
hw_perf_event_update: sdbt 0xb5286008 full 1 over 0 flush_all:0
hw_perf_event_update: sdbt 0xb5286008 full 0 over 0 flush_all:0
above shows 2. interrupt
... this goes on fine until...
hw_perf_event_update: sdbt 0xb5286068 full 1 over 0 flush_all:0
perf_push_sample1: overflow
one or more samples read from the IRQ handler are rejected by
perf_event_overflow() and the IRQ handler advances to the next SDB
and modifies the trailer entry of a partially filled SDB.
hw_perf_event_update: sdbt 0xb5286070 full 0 over 0 flush_all:1
timestamp: 14:32:52.519953
Next time the IRQ handler is called for this SDB the trailer entry shows
an overflow count of 19 missed entries.
hw_perf_event_update: sdbt 0xb5286070 full 1 over 19 flush_all:1
timestamp: 14:32:52.970058
Remove access to a follow on SDB when event overflow happened.
Function perf_event_ever_overflow() and perf_event_account_interrupt()
are called every time samples are processed by the interrupt handler.
However function perf_event_account_interrupt() has checks to avoid being
flooded with interrupts (more then 1000 samples are received per
task_tick). Samples are then dropped and a PERF_RECORD_THROTTLED is
added to the perf data. The perf subsystem limit calculation is:
maximum sample frequency := 100000 --> 1 samples per 10 us
task_tick = 10ms = 10000us --> 1000 samples per task_tick
The work flow is
measurement_alert() uses SDBT head and each SBDT points to 511
SDB pages, each with 126 sample entries. After processing 8 SBDs
and for each valid sample calling:
there is a considerable amount of samples being dropped, especially when
the sample frequency is very high and near the 100000 limit.
To avoid the high amount of samples being dropped near the end of a
task_tick time frame, increment the sampling interval in case of
dropped events. The CPU Measurement sampling facility on the s390
supports only intervals, specifiing how many CPU cycles have to be
executed before a sample is generated. Increase the interval when the
samples being generated hit the task_tick limit.
Fix the lookup method on the dynamic root directory such that creation
calls, such as mkdir, open(O_CREAT), symlink, etc. fail with EOPNOTSUPP
rather than failing with some odd error (such as EEXIST).
lookup() itself tries to create automount directories when it is invoked.
These are cached locally in RAM and not committed to storage.
Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Tested-by: Jonathan Billings <jsbillings@jsbillings.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The socket read/write helpers only look at the file O_NONBLOCK. not
the iocb IOCB_NOWAIT flag. This breaks users like preadv2/pwritev2
and io_uring that rely on not having the file itself marked nonblocking,
but rather the iocb itself.
Cc: netdev@vger.kernel.org Acked-by: David Miller <davem@davemloft.net> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Gadget driver should always use config_ep_by_speed() to initialize
usb_ep struct according to usb device's operating speed. Otherwise,
usb_ep struct may be wrong if usb devcie's operating speed is changed.
The key point in this patch is that we want to make sure the desc pointer
in usb_ep struct will be set to NULL when gadget is disconnected.
This will force it to call config_ep_by_speed() to correctly initialize
usb_ep struct based on the new operating speed when gadget is
re-connected later.
Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: EJ Hsu <ejh@nvidia.com> Signed-off-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Place the declaration of struct nouveau_conn_atom above that of
struct nouveau_connector. This commit makes no changes to the moved
block what so ever, it just moves it up a bit.
This is a preparation patch to fix some issues with connector handling
on pre nv50 displays (which do not use atomic modesetting).
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The discovering of sas port is driven by workqueue in libsas. When libsas
is processing port events or phy events in workqueue, new events may rise
up and change the state of some structures such as asd_sas_phy. This may
cause some problems such as follows:
==>thread 1 ==>thread 2
==>phy up
==>phy_up_v3_hw()
==>oob_mode = SATA_OOB_MODE;
==>phy down quickly
==>hisi_sas_phy_down()
==>sas_ha->notify_phy_event()
==>sas_phy_disconnected()
==>oob_mode = OOB_NOT_CONNECTED
==>workqueue wakeup
==>sas_form_port()
==>sas_discover_domain()
==>sas_get_port_device()
==>oob_mode is OOB_NOT_CONNECTED and device
is wrongly taken as expander
This at last lead to the panic when libsas trying to issue a command to
discover the device.
Fixes: 2908d778ab3e ("[SCSI] aic94xx: new driver") Link: https://lore.kernel.org/r/20191206011118.46909-1-yanaijie@huawei.com Reported-by: Gao Chuan <gaochuan4@huawei.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On this error path we call qla4xxx_mem_free() and then the caller also
calls qla4xxx_free_adapter() which calls qla4xxx_mem_free(). It leads to a
couple double frees:
PORT UPDATE asynchronous event is generated on the host that issues PLOGI
ELS (in the case of higher WWPN). In that case, the event shouldn't be
handled as it sets unwanted DPC flags (i.e. LOOP_RESYNC_NEEDED) that
trigger link flap.
Ignore the event if the host has higher WWPN, but handle otherwise.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-13-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
qlt_handle_login schedules session for deletion even if a login is in
progress. That causes login bouncing, i.e. a few logins are made before it
settles down.
Complete the first login by sending Notify Acknowledge IOCB via
qlt_plogi_ack_unref if the session is pending login completion.
Fixes: 9cd883f07a54 ("scsi: qla2xxx: Fix session cleanup for N2N") Cc: Krishna Kant <krishna.kant@purestorage.com> Cc: Alexei Potashnik <alexei@purestorage.com> Link: https://lore.kernel.org/r/20191125165702.1013-11-r.bolshakov@yadro.com Acked-by: Quinn Tran <qutran@marvell.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
qla2x00_configure_local_loop initializes PLOGI payload for PLOGI ELS using
Get Parameters mailbox command.
In the case when the driver is running in target mode, the topology is N2N
and the target port has higher WWPN, LOCAL_LOOP_UPDATE bit is cleared too
early and PLOGI payload is not initialized by the Get Parameters
command. That causes a failure of ELS IOCB carrying the PLOGI with 0x15 aka
Data Underrun error.
LOCAL_LOOP_UPDATE has to be set to initialize PLOGI payload.
Fixes: 48acad099074 ("scsi: qla2xxx: Fix N2N link re-connect") Link: https://lore.kernel.org/r/20191125165702.1013-10-r.bolshakov@yadro.com Acked-by: Quinn Tran <qutran@marvell.com> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The size of the buffer is hardcoded as 0x70 or 112 bytes, while the size of
ELS IOCB is 0x40 and the size of PLOGI payload returned by Get Parameters
command is 0x74.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-9-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
MBA_PORT_UPDATE generates duplicate log lines in target mode because
qlt_async_event is called twice. Drop the calls within the case as the
function will be called right after the switch statement.
Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-8-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvel.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Acked-by: Himanshu Madhani <hmadhani@marvell.com> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
del_work is already initialized inside qla2x00_alloc_fcport, there's no
need to overwrite it. Indeed, it might prevent complete traversal of
workqueue list.
Fixes: a01c77d2cbc45 ("scsi: qla2xxx: Move session delete to driver work queue") Cc: Quinn Tran <qutran@marvell.com> Link: https://lore.kernel.org/r/20191125165702.1013-5-r.bolshakov@yadro.com Acked-by: Himanshu Madhani <hmadhani@marvell.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log