This code is used only when CONFIG_PREEMPT=n and only in non-atomic context:
xen_in_preemptible_hcall is set only in privcmd_ioctl_hypercall().
Thus preempt_count is zero and should_resched() is equal to need_resched().
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Graf <agraf@suse.de> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20150715095201.12246.49283.stgit@buzz Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Andre Tomt <andre@tomt.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
3w controller don't dma map small single SGL entry commands but instead
bounce buffer them. Add a helper to identify these commands and don't
call scsi_dma_unmap for them.
Based on an earlier patch from James Bottomley.
Fixes: 118c85 ("3w-9xxx: fix command completion race") Reported-by: Tóth Attila <atoth@atoth.sote.hu> Tested-by: Tóth Attila <atoth@atoth.sote.hu> Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Adam Radford <aradford@gmail.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These functions check should_resched() before unlocking spinlock/bh-enable:
preempt_count always non-zero => should_resched() always returns false.
cond_resched_lock() worked iff spin_needbreak is set.
This patch adds argument "preempt_offset" to should_resched().
preempt_count offset constants for that:
PREEMPT_DISABLE_OFFSET - offset after preempt_disable()
PREEMPT_LOCK_OFFSET - offset after spin_lock()
SOFTIRQ_DISABLE_OFFSET - offset after local_bh_distable()
SOFTIRQ_LOCK_OFFSET - offset after spin_lock_bh()
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Graf <agraf@suse.de> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: bdb438065890 ("sched: Extract the basic add/sub preempt_count modifiers") Link: http://lkml.kernel.org/r/20150715095204.12246.98268.stgit@buzz Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unmapped hw queue is remapped after CPU topology is changed,
hctx->tags->cpumask has to be set after hctx->tags is setup in
blk_mq_map_swqueue(), otherwise it causes null pointer dereference.
Fixes: f26cdc8536 ("blk-mq: Shared tag enhancements") Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Keith Busch <keith.busch@intel.com> Cc: Ming Lei <tom.leiming@gmail.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kernels after v3.9 use kmalloc_size(INDEX_NODE + 1) to get the next
larger cache size than the size index INDEX_NODE mapping. In kernels
3.9 and earlier we used malloc_sizes[INDEX_L3 + 1].cs_size.
However, sometimes we can't get the right output we expected via
kmalloc_size(INDEX_NODE + 1), causing a BUG().
The mapping table in the latest kernel is like:
index = {0, 1, 2 , 3, 4, 5, 6, n}
size = {0, 96, 192, 8, 16, 32, 64, 2^n}
The mapping table before 3.10 is like this:
index = {0 , 1 , 2, 3, 4 , 5 , 6, n}
size = {32, 64, 96, 128, 192, 256, 512, 2^(n+3)}
The problem on my mips64 machine is as follows:
(1) When configured DEBUG_SLAB && DEBUG_PAGEALLOC && DEBUG_LOCK_ALLOC
&& DEBUG_SPINLOCK, the sizeof(struct kmem_cache_node) will be "150",
and the macro INDEX_NODE turns out to be "2": #define INDEX_NODE
kmalloc_index(sizeof(struct kmem_cache_node))
(2) Then the result of kmalloc_size(INDEX_NODE + 1) is 8.
(3) Then "if(size >= kmalloc_size(INDEX_NODE + 1)" will lead to "size
= PAGE_SIZE".
(4) Then "if ((size >= (PAGE_SIZE >> 3))" test will be satisfied and
"flags |= CFLGS_OFF_SLAB" will be covered.
(5) if (flags & CFLGS_OFF_SLAB)" test will be satisfied and will go to
"cachep->slabp_cache = kmalloc_slab(slab_size, 0u)", and the result
here may be NULL while kernel bootup.
(6) Finally,"BUG_ON(ZERO_OR_NULL_PTR(cachep->slabp_cache));" causes the
BUG info as the following shows (may be only mips64 has this problem):
This patch fixes the problem of kmalloc_size(INDEX_NODE + 1) and removes
the BUG by adding 'size >= 256' check to guarantee that all necessary
small sized slabs are initialized regardless sequence of slab size in
mapping table.
Fixes: e33660165c90 ("slab: Use common kmalloc_index/kmalloc_size...") Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com> Reported-by: Liuhailong <liu.hailong6@zte.com.cn> Acked-by: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the algorithm. Read systimel twice and check for overflow.
If there was no overflow, use the first value.
If there was an overflow, read systimeh again and use the second
systimel value.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: "Jason A. Donenfeld" <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If atmel_init_gpios fails the port has already been marked as busy (in
line 2629), so this must be undone in the error path.
This bug was introduced because I created the patch that finally
became 722ccf416ac2 ("serial: atmel: fix error handling when
mctrl_gpio_init fails") on top of 3.19 which didn't have commit 6fbb9bdf0f3f ("tty/serial: at91: fix error handling in
atmel_serial_probe()") yet.
This adds an entry to the uart_config table for PORT_RT2880
enabling rx/tx FIFOs. The UART is actually a Palmchip BK-3103
which is found in several devices from Alchemy/RMI, Ralink, and
Sigma Designs.
Signed-off-by: Mans Rullgard <mans@mansr.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There seems to be two problems causing this issue.
First, in drivers/tty/n_tty.c, __receive_buf() stores the data and
updates ldata->commit_head using smp_store_release() and then checks
the wait queue using waitqueue_active(). However, since there is no
memory barrier, __receive_buf() could return without calling
wake_up_interactive_poll(), and at the same time, n_tty_read() could
start to wait in wait_woken() as in the following chart.
__receive_buf() n_tty_read()
------------------------------------------------------------------------
if (waitqueue_active(&tty->read_wait))
/* Memory operations issued after the
RELEASE may be completed before the
RELEASE operation has completed */
add_wait_queue(&tty->read_wait, &wait);
...
if (!input_available_p(tty, 0)) {
smp_store_release(&ldata->commit_head,
ldata->read_head);
...
timeout = wait_woken(&wait,
TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------
The second problem is that n_tty_read() also lacks a memory barrier
call and could also cause __receive_buf() to return without calling
wake_up_interactive_poll(), and n_tty_read() to wait in wait_woken()
as in the chart below.
__receive_buf() n_tty_read()
------------------------------------------------------------------------
spin_lock_irqsave(&q->lock, flags);
/* from add_wait_queue() */
...
if (!input_available_p(tty, 0)) {
/* Memory operations issued after the
RELEASE may be completed before the
RELEASE operation has completed */
smp_store_release(&ldata->commit_head,
ldata->read_head);
if (waitqueue_active(&tty->read_wait))
__add_wait_queue(q, wait);
spin_unlock_irqrestore(&q->lock,flags);
/* from add_wait_queue() */
...
timeout = wait_woken(&wait,
TASK_INTERRUPTIBLE, timeout);
------------------------------------------------------------------------
There are also other places in drivers/tty/n_tty.c which have similar
calls to waitqueue_active(), so instead of adding many memory barrier
calls, this patch simply removes the call to waitqueue_active(),
leaving just wake_up*() behind.
This fixes both problems because, even though the memory access before
or after the spinlocks in both wake_up*() and add_wait_queue() can
sneak into the critical section, it cannot go past it and the critical
section assures that they will be serialized (please see "INTER-CPU
ACQUIRING BARRIER EFFECTS" in Documentation/memory-barriers.txt for a
better explanation). Moreover, the resulting code is much simpler.
Latency measurement using a ping-pong test over a pty doesn't show any
visible performance drop.
The cleaner policy doesn't make use of the per cache block hint space in
the metadata (unlike the other policies). When switching from the
cleaner policy to mq or smq a NULL pointer crash (in dm_tm_new_block)
was observed. The crash was caused by bugs in dm-cache-metadata.c
when trying to skip creation of the hint btree.
The minimal fix is to change hint size for the cleaner policy to 4 bytes
(only hint size supported).
Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leandro Awa writes:
"After switching to version 4.1.6, our parallelized and distributed
workflows now fail consistently with errors of the form:
T34: ./regex.c:39:22: error: config.h: No such file or directory
From our 'git bisect' testing, the following commit appears to be the
possible cause of the behavior we've been seeing: commit 766c4cbfacd8"
Al Viro says:
"What happens is that 766c4cbfacd8 got the things subtly wrong.
We used to treat d_is_negative() after lookup_fast() as "fall with
ENOENT". That was wrong - checking ->d_flags outside of ->d_seq
protection is unreliable and failing with hard error on what should've
fallen back to non-RCU pathname resolution is a bug.
Unfortunately, we'd pulled the test too far up and ran afoul of
another kind of staleness. The dentry might have been absolutely
stable from the RCU point of view (and we might be on UP, etc), but
stale from the remote fs point of view. If ->d_revalidate() returns
"it's actually stale", dentry gets thrown away and the original code
wouldn't even have looked at its ->d_flags.
What we need is to check ->d_flags where 766c4cbfacd8 does (prior to
->d_seq validation) but only use the result in cases where we do not
discard this dentry outright"
On the OMAP AM3517 platform the uart4_ick gets registered
twice, causing any power management to /dev/ttyO3 to fail
when trying to wake the device up.
This solves the following oops:
[] Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa09e008
[] PC is at serial_omap_pm+0x48/0x15c
[] LR is at _raw_spin_unlock_irqrestore+0x30/0x5c
When freqdomain_cpus attribute is read from an offlined cpu, it will
cause crash. This change prevents calling cpufreq_show_cpus when
policy driver_data is NULL.
According to 'FE-2946959' erratum the clock inversion option is
needed to support slow frequencies when the card input hold time
requirement is high. This setting is not required for high speed
MMC and might cause timing violation.
shci-pxav3 driver is enabling by default the
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN quirk. However this quirk is not
required for Armada 38x and leads to wrong clock setting in the divider.
Passing -1 to bitmap_storage_alloc() causes page->index to be set to
-1, which is quite problematic.
So only pass ->cluster_slot if mddev_is_clustered().
Fixes: b97e92574c0b ("Use separate bitmaps for each nodes in the cluster") Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per-IRQ directories in procfs are created only when a handler is first
added to the irqdesc, not when the irqdesc is created. In the case of
a shared IRQ, multiple tasks can race to create a directory. This
race condition seems to have been present forever, but is easier to
hit with async probing.
During driver probing the following code path is triggered.
igb_probe
->igb_sw_init
->igb_probe_vfs
->igb_pci_enable_sriov
->igb_sriov_reinit
Doing the SR-IOV re-init is not necessary during probing since we're
starting from scratch. Here we can call igb_enable_sriov() right away.
Running igb_sriov_reinit() during igb_probe() also seems to cause
occasional packet loss on some onboard 82576 NICs. Reproduced on
Dell and HP servers with onboard 82576 NICs.
Example:
Intel Corporation 82576 Gigabit Network Connection [8086:10c9] (rev 01)
Subsystem: Dell Device [1028:0481]
Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Cc: Daniel J Blueman <daniel@numascale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chas Williams <3chas3@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: "Kamata, Munehisa" <kamatam@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request allocation has been moved to connect_ring, which is called every
time blkback connects to the frontend (this can happen multiple times during
a blkback instance life cycle). On the other hand, request freeing has not
been moved, so it's only called when destroying the backend instance. Due to
this mismatch, blkback can allocate the request pool multiple times, without
freeing it.
In order to fix it, move the freeing of requests to xen_blkif_disconnect to
restore the symmetry between request allocation and freeing.
Reported-by: Julien Grall <julien.grall@citrix.com> Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Tested-by: Julien Grall <julien.grall@citrix.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: David Vrabel <david.vrabel@citrix.com> Cc: xen-devel@lists.xenproject.org Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure the compiler does not modify arguments of syscall functions.
This can happen if the compiler generates a tailcall to another
function. For example, without asmlinkage_protect sys_openat is compiled
into this function:
Note how the fourth argument is modified in place, modifying the register
%d4 that gets restored from this stack slot when the function returns to
user-space. The caller may expect the register to be unmodified across
system calls.
This is the arm64 portion of commit 45cac65b0fcd ("readahead: fault
retry breaks mmap file read random detection"), which was absent from
the initial port and has since gone unnoticed. The original commit says:
> .fault now can retry. The retry can break state machine of .fault. In
> filemap_fault, if page is miss, ra->mmap_miss is increased. In the second
> try, since the page is in page cache now, ra->mmap_miss is decreased. And
> these are done in one fault, so we can't detect random mmap file access.
>
> Add a new flag to indicate .fault is tried once. In the second try, skip
> ra->mmap_miss decreasing. The filemap_fault state machine is ok with it.
With this change, Mark reports that:
> Random read improves by 250%, sequential read improves by 40%, and
> random write by 400% to an eMMC device with dm crypto wrapped around it.
Cc: Shaohua Li <shli@kernel.org> Cc: Rik van Riel <riel@redhat.com> Cc: Wu Fengguang <fengguang.wu@intel.com> Signed-off-by: Mark Salyzyn <salyzyn@android.com> Signed-off-by: Riley Andrews <riandrews@android.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is because when using function graph tracer, if the traced
function return value is in multi regs ([x0-x7]), return_to_handler
may corrupt them. So in return_to_handler, the parameter regs should
be protected properly.
Signed-off-by: Li Bin <huawei.libin@huawei.com> Acked-by: AKASHI Takahiro <takahiro.akashi@linaro.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new Properties Table feature introduced in UEFIv2.5 may
split memory regions that cover PE/COFF memory images into
separate code and data regions. Since these regions only differ
in the type (runtime code vs runtime data) and the permission
bits, but not in the memory type attributes (UC/WC/WT/WB), the
spec does not require them to be aligned to 64 KB.
Since the relative offset of PE/COFF .text and .data segments
cannot be changed on the fly, this means that we can no longer
pad out those regions to be mappable using 64 KB pages.
Unfortunately, there is no annotation in the UEFI memory map
that identifies data regions that were split off from a code
region, so we must apply this logic to all adjacent runtime
regions whose attributes only differ in the permission bits.
So instead of rounding each memory region to 64 KB alignment at
both ends, only round down regions that are not directly
preceded by another runtime region with the same type
attributes. Since the UEFI spec does not mandate that the memory
map be sorted, this means we also need to sort it first.
Note that this change will result in all EFI_MEMORY_RUNTIME
regions whose start addresses are not aligned to the OS page
size to be mapped with executable permissions (i.e., on kernels
compiled with 64 KB pages). However, since these mappings are
only active during the time that UEFI Runtime Services are being
invoked, the window for abuse is rather small.
Tested-by: Mark Salter <msalter@redhat.com> Tested-by: Mark Rutland <mark.rutland@arm.com> [UEFI 2.4 only] Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Matt Fleming <matt.fleming@intel.com> Reviewed-by: Mark Salter <msalter@redhat.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Leif Lindholm <leif.lindholm@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-kernel@vger.kernel.org Link: http://lkml.kernel.org/r/1443218539-7610-3-git-send-email-matt@codeblueprint.co.uk Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rare cases a directory can be renamed out from under a bind mount.
In those cases without special handling it becomes possible to walk up
the directory tree to the root dentry of the filesystem and down
from the root dentry to every other file or directory on the filesystem.
Like division by zero .. from an unconnected path can not be given
a useful semantic as there is no predicting at which path component
the code will realize it is unconnected. We certainly can not match
the current behavior as the current behavior is a security hole.
Therefore when encounting .. when following an unconnected path
return -ENOENT.
- Add a function path_connected to verify path->dentry is reachable
from path->mnt.mnt_root. AKA to validate that rename did not do
something nasty to the bind mount.
To avoid races path_connected must be called after following a path
component to it's next path component.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A rename can result in a dentry that by walking up d_parent
will never reach it's mnt_root. For lack of a better term
I call this an escaped path.
prepend_path is called by four different functions __d_path,
d_absolute_path, d_path, and getcwd.
__d_path only wants to see paths are connected to the root it passes
in. So __d_path needs prepend_path to return an error.
d_absolute_path similarly wants to see paths that are connected to
some root. Escaped paths are not connected to any mnt_root so
d_absolute_path needs prepend_path to return an error greater
than 1. So escaped paths will be treated like paths on lazily
unmounted mounts.
getcwd needs to prepend "(unreachable)" so getcwd also needs
prepend_path to return an error.
d_path is the interesting hold out. d_path just wants to print
something, and does not care about the weird cases. Which raises
the question what should be printed?
Given that <escaped_path>/<anything> should result in -ENOENT I
believe it is desirable for escaped paths to be printed as empty
paths. As there are not really any meaninful path components when
considered from the perspective of a mount tree.
So tweak prepend_path to return an empty path with an new error
code of 3 when it encounters an escaped path.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When get a CRC error, start the mmc_retune, it will issue CMD19/CMD21
to do tune, assume there were 10 clock phase need to try, phase 0 to
phase 6 is ok, phase 7 to phase 9 is NG, we try it from 0 to 9, so
the last CMD19/CMD21 will get CRC error, host->need_retune was set and
cause mmc_retune was called, then dead loop of mmc_retune
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_GPIOLIB is unset, its stubs will return -ENOSYS. That means
when the mmc core parses DT for CD/WP GPIOs via mmc_of_parse(), -ENOSYS
becomes propagated to the caller. Typically this means that the mmc host
driver fails to probe.
As the CD/WP GPIOs are already treated as optional, let's extend that to
cover the case when CONFIG_GPIOLIB is unset.
Reported-by: Michal Simek <michal.simek@xilinx.com> Fixes: 16b23787fc70 ("mmc: sdhci-of-arasan: Call OF parsing for MMC") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a v4.2+ regression introduced by commit c04a6091
that removed support for obsolete sync-and-steering markers usage
as originally defined in RFC-3720.
The regression would involve attempting to send OFMarker=No +
IFMarker=No keys during opertional negotiation login phase,
including when initiators did not actually propose these keys.
The result for MSFT iSCSI initiators would be random junk in
TCP stream after the last successful login request was been sent
signaling the move to full feature phase (FFP) operation.
To address this bug, go ahead and avoid negotiating these keys
by default unless the initiator explicitly proposes them, but
still respond to them with 'No' if they are proposed.
The builds of allmodconfig of avr32 is failing with:
drivers/net/ethernet/via/via-rhine.c:1098:2: error: implicit declaration
of function 'pci_iomap' [-Werror=implicit-function-declaration]
drivers/net/ethernet/via/via-rhine.c:1119:2: error: implicit declaration
of function 'pci_iounmap' [-Werror=implicit-function-declaration]
The generic empty pci_iomap and pci_iounmap is used only if CONFIG_PCI
is not defined and CONFIG_GENERIC_PCI_IOMAP is defined.
Add GENERIC_PCI_IOMAP in the dependency list for VIA_RHINE as we are
getting build failure when CONFIG_PCI and CONFIG_GENERIC_PCI_IOMAP both
are not defined.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
UBI error: init_volumes: not enough PEBs, required 706, available 686
UBI error: ubi_wl_init: no enough physical eraseblocks (-20, need 1)
UBI error: ubi_attach_mtd_dev: failed to attach mtd1, error -12 <= NOT ENOMEM
UBI error: ubi_init: cannot attach mtd1
If available PEBs are not enough when initializing volumes, return -ENOSPC
directly. If available PEBs are not enough when initializing WL, return
-ENOSPC instead of -ENOMEM.
Signed-off-by: Sheng Yong <shengyong1@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: David Gstir <david@sigma-star.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that data_size is less than LEB size.
Otherwise a handcrafted UBI image is able to trigger
an out of bounds memory access in ubi_compare_lebs().
Signed-off-by: Richard Weinberger <richard@nod.at> Reviewed-by: David Gstir <david@sigma-star.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the lockdep splat is a false positive, becuase path_openat holds i_mutex
of the parent directory and ubifs_init_security() tries to acquire i_mutex
of a new inode, it reveals that taking i_mutex in ubifs_init_security() is
in vain because it is only being called in the inode allocation path
and therefore nobody else can see the inode yet.
Reported-and-tested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-and-tested-by: Dongsheng Yang <yangds.fnst@cn.fujitsu.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: dedekind1@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5d5cd85ff441 ("rsi: Fix failure to load firmware after memory
leak fix and fix the leak") also added a check on the allocation of
DMA-accessible memory that may directly return. In that case the
already allocated firmware data is leaked. Make sure the data is
always freed correctly. Detected by Coverity CID 1316519.
Fixes: 5d5cd85ff441 ("rsi: Fix failure to load firmware after memory leak fix and fix the leak") Signed-off-by: Christian Engelmayer <cengelma@gmx.at> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a race which can result in the same virtual IRQ number
being assigned to two different MSI interrupts. The most visible
consequence of that is usually a warning and stack trace from the
sysfs code about an attempt to create a duplicate entry in sysfs.
The race happens when one CPU (say CPU 0) is disposing of an MSI
while another CPU (say CPU 1) is setting up an MSI. CPU 0 calls
(for example) pnv_teardown_msi_irqs(), which calls
msi_bitmap_free_hwirqs() to indicate that the MSI (i.e. its
hardware IRQ number) is no longer in use. Then, before CPU 0 gets
to calling irq_dispose_mapping() to free up the virtal IRQ number,
CPU 1 comes in and calls msi_bitmap_alloc_hwirqs() to allocate an
MSI, and gets the same hardware IRQ number that CPU 0 just freed.
CPU 1 then calls irq_create_mapping() to get a virtual IRQ number,
which sees that there is currently a mapping for that hardware IRQ
number and returns the corresponding virtual IRQ number (which is
the same virtual IRQ number that CPU 0 was using). CPU 0 then
calls irq_dispose_mapping() and frees that virtual IRQ number.
Now, if another CPU comes along and calls irq_create_mapping(), it
is likely to get the virtual IRQ number that was just freed,
resulting in the same virtual IRQ number apparently being used for
two different hardware interrupts.
To fix this race, we just move the call to msi_bitmap_free_hwirqs()
to after the call to irq_dispose_mapping(). Since virq_to_hw()
doesn't work for the virtual IRQ number after irq_dispose_mapping()
has been called, we need to call it before irq_dispose_mapping() and
remember the result for the msi_bitmap_free_hwirqs() call.
The pattern of calling msi_bitmap_free_hwirqs() before
irq_dispose_mapping() appears in 5 places under arch/powerpc, and
appears to have originated in commit 05af7bd2d75e ("[POWERPC] MPIC
U3/U4 MSI backend") from 2007.
So far the mcast tvlv handler did not anticipate the processing of
multiple incoming OGMs from the same originator at the same time. This
can lead to various issues:
* Broken refcounting: For instance two mcast handlers might both assume
that an originator just got multicast capabilities and will together
wrongly decrease mcast.num_disabled by two, potentially leading to
an integer underflow.
* Potential kernel panic on hlist_del_rcu(): Two mcast handlers might
one after another try to do an
hlist_del_rcu(&orig->mcast_want_all_*_node). The second one will
cause memory corruption / crashes.
(Reported by: Sven Eckelmann <sven@narfation.org>)
Right in the beginning the code path makes assumptions about the current
multicast related state of an originator and bases all updates on that. The
easiest and least error prune way to fix the issues in this case is to
serialize multiple mcast handler invocations with a spinlock.
Fixes: 60432d756cf0 ("batman-adv: Announce new capability via multicast TVLV") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Fixes: 60432d756cf0 ("batman-adv: Announce new capability via multicast TVLV") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Antonio Quartulli <antonio@meshcoding.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
The CONFIG_MIPS_MT symbol can be selected by CONFIG_MIPS_VPE_LOADER in
addition to CONFIG_MIPS_MT_SMP. We only want MT code in the CPS SMP boot
vector if we're using MT for SMP. Thus switch the config symbol we ifdef
against to CONFIG_MIPS_MT_SMP.
The MT-specific code in mips_cps_boot_vpes can safely be omitted from
kernels which don't support MT, with the default VPE==0 case being used
as it would be after the has_mt (Config3.MT) check failed at runtime.
Discarding the code entirely will save us a few bytes & allow cleaner
handling of MT ASE instructions by later patches.
The has_mt macro ended with a branch, leaving its callers with a delay
slot that would be executed if Config3.MT is not set. However it would
not be executed if Config3 (or earlier Config registers) don't exist
which makes it somewhat inconsistent at best. Fill the delay slot in the
macro & fix the mips_cps_boot_vpes caller appropriately.
If there is a DMA zone (usually 24bit = 16MB I believe), but no DMA32
zone, as is the case for some 32-bit kernels, then massage_gfp_flags()
will cause DMA memory allocated for devices with a 32..63-bit
coherent_dma_mask to fall back to using __GFP_DMA, even though there may
only be 32-bits of physical address available anyway.
Correct that case to compare against a mask the size of phys_addr_t
instead of always using a 64-bit mask.
The rotr, seh and wsbh instructions have been introduced with the R2
ISA. Thus the current BPF code fails to build on pre-R2 little endian
CPUs:
CC arch/mips/net/bpf_jit.o
AS arch/mips/net/bpf_jit_asm.o
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S: Assembler messages:
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:67: Error: opcode not supported on this processor: mips32 (mips32) `wsbh $8,$19'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:68: Error: opcode not supported on this processor: mips32 (mips32) `rotr $19,$8,16'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:83: Error: opcode not supported on this processor: mips32 (mips32) `wsbh $8,$19'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:84: Error: opcode not supported on this processor: mips32 (mips32) `seh $19,$8'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:151: Error: opcode not supported on this processor: mips32 (mips32) `wsbh $8,$12'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:153: Error: opcode not supported on this processor: mips32 (mips32) `rotr $19,$8,16'
/home/aurel32/linux-4.2/arch/mips/net/bpf_jit_asm.S:164: Error: opcode not supported on this processor: mips32 (mips32) `wsbh $19,$12'
/home/aurel32/linux-4.2/scripts/Makefile.build:294: recipe for target 'arch/mips/net/bpf_jit_asm.o' failed
Fix that by providing equivalent code for these CPUs.
On little endian, avoid generating the big endian version of the code
by using #else in addition to #ifdef #endif. Also fix one alignment
issue wrt delay slot.
Commit a6335fa1 fixed the case with gap between initrd and next usable PFN zone,
but broken the case when initrd is combined with usable memory into one region
(in add_memory_region()). Restore the fixup initially brought in by f9a7febd.
---- error message ----
Unpacking initramfs...
Initramfs unpacking failed: junk in compressed archive
BUG: Bad page state in process swapper pfn:00261
page:81004c20 count:0 mapcount:-127 mapping: (null) index:0x2
flags: 0x0()
page dumped because: nonzero mapcount
CPU: 0 PID: 1 Comm: swapper Not tainted 4.2.0+ #1782
-----------------------
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Reported-by: Tony Wu <tung7970@gmail.com> Tested-by: Tony Wu <tung7970@gmail.com> Cc: David Daney <david.daney@cavium.com> Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: Joe Perches <joe@perches.com> Cc: Steven J. Hill <Steven.Hill@imgtec.com> Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11086/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3adeb2566b9b ("MIPS: Loongson: Improve LEFI firmware interface")
made the number of UARTs dynamic if LEFI_FIRMWARE_INTERFACE is configured.
Unfortunately, it did not initialize the number of UARTs if
LEFI_FIRMWARE_INTERFACE is not configured. As a result, the Fulong2e
system has no console.
Tolerance applies on both sides of the target voltage, i.e. both min and
max sides. But while checking if a voltage is supported by the regulator
or not, we haven't taken care of tolerance on the lower side. Fix that.
Cc: Lucas Stach <l.stach@pengutronix.de> Fixes: 045ee45c4ff2 ("cpufreq: cpufreq-dt: disable unsupported OPPs") Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Reviewed-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cache_shared_cpu_map_setup() did check sibling CPUs cacheinfo descriptor
while the respective teardown path cache_shared_cpu_map_remove() didn't.
Fix that.
>From tglx's version: to be on the safe side, move the cacheinfo
descriptor check to free_cache_attributes(), thus cleaning up the
hotplug path a little and making this even more robust.
The mv_cesa_queue_req() function calls crypto_enqueue_request() to
enqueue a request. In the normal case (i.e the queue isn't full), this
function returns -EINPROGRESS. The current Marvell CESA crypto driver
takes this into account and cleans up the request only if an error
occured, i.e if the return value is not -EINPROGRESS.
Unfortunately this causes problems with
CRYPTO_TFM_REQ_MAY_BACKLOG-flagged requests. When such a request is
passed to crypto_enqueue_request() and the queue is full,
crypto_enqueue_request() will return -EBUSY, but will keep the request
enqueued nonetheless. This situation was not properly handled by the
Marvell CESA driver, which was anyway cleaning up the request in such
a situation. When later on the request was taken out of the backlog
and actually processed, a kernel crash occured due to the internal
driver data structures for this structure having been cleaned up.
To avoid this situation, this commit adds a
mv_cesa_req_needs_cleanup() helper function which indicates if the
request needs to be cleaned up or not after a call to
crypto_enqueue_request(). This helper allows to do the cleanup only in
the appropriate cases, and all call sites of mv_cesa_queue_req() are
fixed to use this new helper function.
Reported-by: Vincent Donnefort <vdonnefort@gmail.com> Fixes: db509a45339fd ("crypto: marvell/cesa - add TDMA support") Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Vincent Donnefort <vdonnefort@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a device quirk for the Logitech PTZ Pro Camera and its sibling the
ConferenceCam CC3000e Camera.
This fixes the failed camera enumeration on some boot, particularly on
machines with fast CPU.
Tested by connecting a Logitech PTZ Pro Camera to a machine with a
Haswell Core i7-4600U CPU @ 2.10GHz, and doing thousands of reboot cycles
while recording the kernel logs and taking camera picture after each boot.
Before the patch, more than 7% of the boots show some enumeration transfer
failures and in a few of them, the kernel is giving up before actually
enumerating the webcam. After the patch, the enumeration has been correct
on every reboot.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
since commit 33c300cb90a6 ("usb: musb: dsps:
don't fake of_node to musb core") we have been
preventing CPPI 4.1 from probing due to NULL
of_node. We can't revert said commit otherwise
a different regression would show up, so the fix
is to look for the parent device's (glue layer's)
of_node instead, since that's the thing which
is actually described in DTS.
Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gpio-desc migration done in v4.0 caused a regression
with legacy boots due to reversed reset logic.
e.g. omap3-beagle USB host breaks on legacy boot.
Request the reset GPIO with GPIOF_ACTIVE_LOW flag so that
it matches the driver logic and pin behaviour.
Fixes: e9f2cefb0cdc ("usb: phy: generic: migrate to gpio_desc") Tested-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to spec, there are functional and protocol stalls.
For functional stall, it is for bulk and interrupt endpoints,
below are cases for it:
- Host sends SET_FEATURE request for Set-Halt, the udc driver
needs to set stall, and return true unconditionally.
- The gadget driver may call usb_ep_set_halt to stall certain
endpoints, if there is a transfer in pending, the udc driver
should not set stall, and return -EAGAIN accordingly.
These two kinds of stall need to be cleared by host using CLEAR_FEATURE
request (Clear-Halt).
For protocol stall, it is for control endpoint, this stall will
be set if the control request has failed. This stall will be
cleared by next setup request (hardware will do it).
It fixed usbtest (drivers/usb/misc/usbtest.c) Test 13 "set/clear halt"
test failure, meanwhile, this change has been verified by
USB2 CV Compliance Test and MSC Tests.
Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Felipe Balbi <balbi@ti.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the regression caused by commit ad78c918602 ("usb: musb: dsps: just
start polling already") which causes polling the ID pin status even in
device-only mode.
Fixes: ad78c918602c ("usb: musb: dsps: just start polling already") Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The in kernel snprintf() will conveniently return the actual length of
the printed string even if not given an output beffer at all so just do
that rather than relying on the user to pass in a suitable buffer,
ensuring that we don't need to worry if the buffer was truncated due to
the size of the buffer passed in.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a read is attempted which is smaller than the line length then we may
underflow the subtraction we're doing with the unsigned size_t type so
move some of the calculation to be additions on the right hand side
instead in order to avoid this.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary check that disabled SIS pipe commands for SIS-32
devices. This change was sufficient to enable raw mode and send SIS
pipe commands for a 57B3 device.
Fixes: f8ee25d7d239 ("ipr: AF DASD raw mode implementation in ipr driver") Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com> Reviewed-by: Wen Xiong <wenxiong@linux.vnet.ibm.com> Acked-by: Brian King <brking@linux.vnet.ibm.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the lack of clk_put() in sa11xx_base.c's error cleanup paths by
converting the driver to the devm_* API.
Fixes: 86d88bfca475 ("ARM: 8247/2: pcmcia: sa1100: make use of device clock") Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vif's vdev_id is used as queue number. However due
to the tx pausing design in ath10k it was possible
for a new interface to be created with its tx
queue stopped (via ieee80211_stop_queues). This
could in turn leave the interface inoperable until
ath10k_mac_tx_unlock() was called.
This problem only affected multi-vif scenarios when
new interfaces were created some time later after
other interfaces have been running for some time
and had Tx queue full at some point prior.
Possible manifestation of the bug was
authentication timeout for a client vif.
Fixes: 96d828d45e16 ("ath10k: rework tx queue locking") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once HTT Tx queue got full offchannel queue was
stopped and never woken up again. This broke, e.g.
P2P. This could be reproduced after running a lot
of traffic enough to saturate 100% of the driver
Tx queue and then trying to send offchannel
traffic.
Fixes: 96d828d45e16 ("ath10k: rework tx queue locking") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Firmware peer entries are involved in internal
firmware vdev structures. This was not accounted
for and could lead firmware to crash due to asking
it to do more than it could.
Fixes: 039a0051ec1a ("ath10k: allocate fw resources for iface combinations") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though there's a WMI enum for fragmentation
threshold no known firmware actually implements
it. Moreover it is not possible to rely frame
fragmentation to mac80211 because firmware clears
the "more fragments" bit in frame control making
it impossible for remote devices to reassemble
frames.
Hence implement a dummy callback just to say
fragmentation isn't supported. This effectively
prevents mac80211 from doing frame fragmentation
in software.
This fixes Tx becoming broken after setting
fragmentation threshold.
Fixes: 1010ba4c5d1c ("ath10k: unregister and remove frag_threshold callback") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever any vdev was supposed to be paused all Tx
queues were stopped (except offchannel) instead of
only these associated with the given vdev.
This caused subtle issues with
multi-channel/multi-vif scenarios, e.g.
authentication of station vif could sometimes fail
depending on fw tx pause request timing.
Fixes: b4aa539dd8f2 ("ath10k: implement tx pause wmi event") Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In device_add_property_set() we check pset parameter for a NULL, but few lines
later we do a pointer arithmetic without check that will crash kernel in the
set_secondary_fwnode().
Here we check if pset parameter is NULL and return immediately.
Fixes: 16ba08d5c9ec (device property: Introduce firmware node type for platform data) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rockchip io-domain driver currently only depends on ARCH_ROCKCHIP
itself. This makes it possible to select the power-domain driver, but
not the POWER_AVS class and results in the iodomain-driver not getting
build in this case.
So add the additional dependency, which also results in the driver
config option now being placed nicely into the AVS submenu.
Fixes: 662a958638bd ("PM / AVS: rockchip-io: add driver handling Rockchip io domains") Signed-off-by: Heiko Stuebner <heiko@sntech.de> Acked-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The string "cmd %d RESET FAILED, new lockup detected" is not quite
large enough so the sprintf() will overflow. I have increased the size
of the buffer and also changed the sprintf calls to snprintf.
Fixes: 73153fe533bc ('hpsa: use block layer tag for command allocation') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Don Brace <don.brace@pmcs.com> Signed-off-by: James Bottomley <JBottomley@Odin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USER_DATA register cannot be accessed using byte accessors on A13
SoCs, thus triggering a bug when using memcpy_toio on this register.
Declare an helper macros to convert an OOB buffer into a suitable
USER_DATA value and vice-versa.
This patch also fixes an error in the oob_required logic (some OOB data
are not written even if the user required it) by removing the
oob_required condition, which is perfectly valid since the core already
fill ->oob_poi with FFs when oob_required is false.
When keeping the configuration set by the bootloader (by using
the marvell,nand-keep-config property), the pxa3xx_nand_detect_config()
function is called and set the chunk size to 512 as a default value if
NDCR_PAGE_SZ is not set.
In the other case, when not keeping the bootloader configuration, no
chunk size is set. Fix this by adding a default chunk size of 512.
Unsigned is never less than zero so this error handling won't work.
Fixes: be052cc87745 ('extcon: Fix hang and extcon_get/set_cable_state().') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Roger Quadros <rogerq@ti.com>
[cw00.choi: Change the patch title and fix signedness bug of find_cable_index_by_id() ] Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the ITS is configured for non-cacheable transactions, make sure
that the allocated, zeroed memory is flushed to the Point of
Coherency, allowing the ITS to observe the zeros instead of random
garbage (or even get its own data overwritten by zeros being evicted
from the cache...).
Fixes: 241a386c7dbb "irqchip: gicv3-its: Use non-cacheable accesses when no shareability" Reported-and-tested-by: Stuart Yoder <stuart.yoder@freescale.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: Pavel Fedin <p.fedin@samsung.com> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1442142873-20213-3-git-send-email-marc.zyngier@arm.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When masking/unmasking interrupts, mask_cache is updated and used later
for suspend/resume. Unfortunately, it always was the mask_cache
associated with the first irq chip which was updated. So when performing
resume, only irqs 0-31 could be enabled.
Linux cifs mount with ntlmssp against an Mac OS X (Yosemite
10.10.5) share fails in case the clocks differ more than +/-2h:
digest-service: digest-request: od failed with 2 proto=ntlmv2
digest-service: digest-request: kdc failed with -1561745592 proto=ntlmv2
Fix this by (re-)using the given server timestamp for the
ntlmv2 authentication (as Windows 7 does).
A related problem was also reported earlier by Namjae Jaen (see below):
Windows machine has extended security feature which refuse to allow
authentication when there is time difference between server time and
client time when ntlmv2 negotiation is used. This problem is prevalent
in embedded enviornment where system time is set to default 1970.
Modern servers send the server timestamp in the TargetInfo Av_Pair
structure in the challenge message [see MS-NLMP 2.2.2.1]
In [MS-NLMP 3.1.5.1.2] it is explicitly mentioned that the client must
use the server provided timestamp if present OR current time if it is
not
Reported-by: Namjae Jeon <namjae.jeon@samsung.com> Signed-off-by: Peter Seiderer <ps.report@gmx.net> Signed-off-by: Steve French <smfrench@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per DW MobileStorage databook "each descriptor can transfer up to 4kB
of data in chained mode", moreover buffer size that is put in "des1" is
limited to 13 bits, i.e. for example on attempt to
IDMAC_SET_BUFFER1_SIZE(desc, 8192) size value that's effectively written
will be 0.
On the platform with 8kB PAGE_SIZE I see dw_mmc gets data blocks in
SG-list of 8kB size and that leads to unpredictable behavior of the
SD/MMC controller.
In particular on write to FAT partition of SD-card the controller will
stuck in the middle of DMA transaction.
Solution to the problem is simple - we need to pass large (> 4kB) data
buffers to the controller via multiple descriptors. And that's what
that change does.
What's interesting I did try original driver on same platform but
configured with 4kB PAGE_SIZE and may confirm that data blocks passed
in SG-list to dw_mmc never exeed 4kB limit - that explains why nobody
ever faced a problem I did.
build_dyn_power_table() allocates the power table while holding
rcu_read_lock. kcalloc using GFP_KERNEL may sleep, so it can't be
called in an RCU read-side path.
Move the rcu protection to the part of the function that really needs
it: the part that handles the dev_pm_opp pointer received from
dev_pm_opp_find_freq_ceil(). In the unlikely case that there is an OPP
added to the cpu while this function is running, return -EAGAIN.
Bitwise OR/AND assignments in C aren't guaranteed to be atomic. One
OGM handler might undo the set/clear of a specific bit from another
handler run in between.
Fix this by using the atomic set_bit()/clear_bit()/test_bit() functions.
As reported by Dmitry Vyukov, we really shouldn't do ipc_addid() before
having initialized the IPC object state. Yes, we initialize the IPC
object in a locked state, but with all the lockless RCU lookup work,
that IPC object lock no longer means that the state cannot be seen.
We already did this for the IPC semaphore code (see commit e8577d1f0329:
"ipc/sem.c: fully initialize sem_array before making it visible") but we
clearly forgot about msg and shm.
This commit checks for the URB_ZERO_PACKET flag and creates an extra
zero-length td if the urb transfer length is a multiple of the endpoint's
max packet length.
projects / linux-stable / log