When building with allmodconfig the build was failing with the error:
arch/tile/kernel/usb.c:70:1: warning: data definition has no type or storage class [enabled by default]
arch/tile/kernel/usb.c:70:1: error: type defaults to 'int' in declaration of 'arch_initcall' [-Werror=implicit-int]
arch/tile/kernel/usb.c:70:1: warning: parameter names (without types) in function declaration [enabled by default]
arch/tile/kernel/usb.c:63:19: warning: 'tilegx_usb_init' defined but not used [-Wunused-function]
Include linux/module.h to resolve the build failure.
We should never allow to enable/disable any facilities for the guest
when other VCPUs were already created.
kvm_arch_vcpu_(load|put) relies on SIMD not changing during runtime.
If somebody would create and run VCPUs and then decides to enable
SIMD, undefined behaviour could be possible (e.g. vector save area
not being set up).
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit 8c058b0b9c34 ("x86/irq: Probe for PIC presence before
allocating descs for legacy IRQs") early_irq_init() will no longer
preallocate descriptors for legacy interrupts if PIC does not
exist, which is the case for Xen PV guests.
Therefore we may need to allocate those descriptors ourselves.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Suggested-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recently introduced lnet_peer_set_alive() function uses
get_seconds() to read the current time into a shared variable,
but all other uses of that variable compare it to jiffies values.
This changes the current use to jiffies as well for consistency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: af3fa7c71bf ("staging/lustre/lnet: peer aliveness status and NI status") Cc: Liang Zhen <liang.zhen@intel.com> Cc: James Simmons <uja.ornl@gmail.com> Cc: Isaac Huang <he.huang@intel.com> Signed-off-by: Oleg Drokin <oleg.drokin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com> Tested-by: Joe Lawrence <joe.lawrence@stratus.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 0fd972a7d91d (module: relocate module_init from init.h to
module.h) broke the build of ttyFDC driver due to that driver's (mis)use
of module_mips_cdmm_driver() without first including module.h, for
example:
In file included from ./arch/mips/include/asm/cdmm.h +11 :0,
from drivers/tty/mips_ejtag_fdc.c +34 :
include/linux/device.h +1295 :1: warning: data definition has no type or storage class
./arch/mips/include/asm/cdmm.h +84 :2: note: in expansion of macro ‘module_driver’
drivers/tty/mips_ejtag_fdc.c +1157 :1: note: in expansion of macro ‘module_mips_cdmm_driver’
include/linux/device.h +1295 :1: error: type defaults to ‘int’ in declaration of ‘module_init’ [-Werror=implicit-int]
./arch/mips/include/asm/cdmm.h +84 :2: note: in expansion of macro ‘module_driver’
drivers/tty/mips_ejtag_fdc.c +1157 :1: note: in expansion of macro ‘module_mips_cdmm_driver’
drivers/tty/mips_ejtag_fdc.c +1157 :1: warning: parameter names (without types) in function declaration
Instead of just adding the module.h include, switch to using the new
builtin_mips_cdmm_driver() helper macro and drop the remove callback,
since it isn't needed. If module support is added later, the code can
always be resurrected.
One of the many faults of the QinHeng CH345 USB MIDI interface chip is
that it does not handle received SysEx messages correctly -- every second
event packet has a wrong code index number, which is the one from the last
seen message, instead of 4. For example, the two messages "FE F0 01 02 03
04 05 06 07 08 09 0A 0B 0C 0D 0E F7" result in the following event
packets:
A class-compliant driver must interpret an event packet with CIN 15 as
having a single data byte, so the other two bytes would be ignored. The
message received by the host would then be missing two bytes out of six;
in this example, "F0 01 02 03 06 07 08 09 0C 0D 0E F7".
These corrupted SysEx event packages contain only data bytes, while the
CH345 uses event packets with a correct CIN value only for messages with
a status byte, so it is possible to distinguish between these two cases by
checking for the presence of this status byte.
(Other bugs in the CH345's input handling, such as the corruption resulting
from running status, cannot be worked around.)
The CH345 USB MIDI chip has two output ports. However, they are
multiplexed through one pin, and the number of ports cannot be reduced
even for hardware that implements only one connector, so for those
devices, data sent to either port ends up on the same hardware output.
This becomes a problem when both ports are used at the same time, as
longer MIDI commands (such as SysEx messages) are likely to be
interrupted by messages from the other port, and thus to get lost.
It would not be possible for the driver to detect how many ports the
device actually has, except that in practice, _all_ devices built with
the CH345 have only one port. So we can just ignore the device's
descriptors, and hardcode one output port.
Thomas reports
"
4gsystems sells two total different LTE-surfsticks under the same name.
..
The newer version of XS Stick W100 is from "omega"
..
Under windows the driver switches to the same ID, and uses MI03\6 for
network and MI01\6 for modem.
..
echo "1c9e 9b01" > /sys/bus/usb/drivers/qmi_wwan/new_id
echo "1c9e 9b01" > /sys/bus/usb-serial/drivers/option1/new_id
The callback registered by the musb driver has to comply to the latter,
but up to now had "offset" first which effectively made the function
broken for correct users. So flip the order and while at it also
switch to the parameter names of struct usb_phy_io_ops's write.
The DEVICE_HWI type was added under the faulty assumption that Huawei
devices based on Qualcomm chipsets and firmware use the static USB
interface numbering known from Gobi devices. But this model does
not apply to Huawei devices like the HP branded lt4112 (Huawei me906e).
Huawei firmwares will dynamically assign interface numbers. Functions
are renumbered when the firmware is reconfigured.
Fix by changing the DEVICE_HWI type to use a simplified version
of Huawei's subclass + protocol scheme: Blacklisting known network
interface combinations and assuming the rest are serial.
Reported-and-tested-by: Muri Nicanor <muri+libqmi@immerda.ch> Tested-by: Martin Hauke <mardnh@gmx.de> Fixes: e7181d005e84 ("USB: qcserial: Add support for HP lt4112 LTE/HSPA+ Gobi 4G Modem") Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems like this device has same vendor and product IDs as G2K
devices, but it has different number of interfaces(4 vs 5) and also
different interface layout which makes it currently unusable:
usbcore: registered new interface driver qcserial
usbserial: USB Serial support registered for Qualcomm USB modem
usb 2-1.2: unknown number of interfaces: 5
It is not permitted to set task state before lock. usblp_wwait sets
the state to TASK_INTERRUPTIBLE and calls mutex_lock_interruptible.
Upon return from that function, the state will be TASK_RUNNING again.
Commit d445913ce0ab7f ("usb: ehci-orion: add optional PHY support")
added support for optional phys, but devm_phy_optional_get returns
-ENOSYS if GENERIC_PHY is not enabled.
This causes probe failures, even when there are no phys specified:
[ 1.443365] orion-ehci f1058000.usb: init f1058000.usb fail, -38
[ 1.449403] orion-ehci: probe of f1058000.usb failed with error -38
Some i.mx platforms need three clocks to let controller work, but
others only need one, refine clock operation to adapt for all
platforms, it fixes a regression found at i.mx27.
Certain Synopsys prototyping PHY boards are not able to meet timings
constraints for LPM. This allows the PHY to meet those timings by
leaving the PHY clock running during suspend.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch allows the dwc3 driver to run on the new Synopsys USB 3.1
IP core, albeit in USB 3.0 mode only.
The Synopsys USB 3.1 IP (DWC_usb31) retains mostly the same register
interface and programming model as the existing USB 3.0 controller IP
(DWC_usb3). However the GSNPSID and version numbers are different.
Add checking for the new ID to pass driver probe.
Also, since the DWC_usb31 version number is lower in value than the
full GSNPSID of the DWC_usb3 IP, we set the high bit to identify
DWC_usb31 and to ensure the values are higher.
Finally, add a documentation note about the revision numbering scheme.
Any future revision checks (for STARS, workarounds, and new features)
should take into consideration how it applies to both the 3.1/3.0 IP.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This ID is for the Synopsys DWC_usb3 core with AXI interface on PCIe
HAPS platform. This core has the debug registers mapped at a separate
BAR in order to support enhanced hibernation.
Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to support load and unload gadget driver in full OTG mode.
Signed-off-by: Li Jun <jun.li@freescale.com> Signed-off-by: Peter Chen <peter.chen@freescale.com> Tested-by: Jiada Wang <jiada_wang@mentor.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some SoCs, dwc3 is implemented as a USB2.0 only
core, meaning that it can't ever achieve SuperSpeed.
Currect driver always sets gadget.max_speed to
USB_SPEED_SUPER unconditionally. This can causes
issues to some Host stacks where the host will issue
a GetBOS() request and we will reply with a BOS
containing Superspeed Capability Descriptor.
At least Windows seems to be upset by this fact and
prints a warning that we should connect $this device
to another port.
[ balbi@ti.com : rewrote entire commit, including
source code comment to make a lot clearer what the
problem is ]
Signed-off-by: Ben McCauley <ben.mccauley@garmin.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following changes that appeared in lk 4.0.0, the gadget udc driver for
some ARM based Atmel SoCs (e.g. at91sam9x5 and sama5d3 families)
incorrectly deduced full-speed USB link speed even when the hardware
had negotiated a high-speed link. The fix is to make sure that the
UDPHS Interrupt Enable Register value does not mask the SPEED bit
in the Interrupt Status Register.
For a mass storage gadget this problem lead to failures when the host
had a USB 3 port with the xhci_hcd driver. If the host was a USB 2
port using the ehci_hcd driver then the mass storage gadget worked
(but probably at a lower speed than it should have).
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Fixes: 9870d895ad87 ("usb: atmel_usba_udc: Mask status with enabled irqs") Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Defect 7374 workaround enables all GPEP as endpoint 0. Restore
endpoint number when defect 7374 workaround is disabled. Otherwise,
check to match USB endpoint number to hardware endpoint number in
net2280_enable() fails.
Reported-by: Paul Jones <p.jones@teclyn.com> Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As it breaks g_ether on my Baytrail FFRD8 device. Everything starts out
fine, but after a bit of data has been transferred it just stops
flowing.
Note that I do get a bunch of these "NOHZ: local_softirq_pending 08"
when booting the machine, but I'm not really sure if they're related
to this problem.
Cc: Felipe Balbi <balbi@ti.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: linux-usb@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 383d0b050106 ("KVM: s390: handle pending local interrupts via
bitmap") introduced a possible memory overwrite from user space.
User space could pass an invalid emergency signal code (sending VCPU)
and therefore exceed the bitmap. Let's take care of this case and
check that the id is in the valid range.
Reviewed-by: Dominik Dingel <dingel@linux.vnet.ibm.com> Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We seemed to have missed a few corner cases in commit f6c137ff00a4
("KVM: s390: randomize sca address").
The SCA has a maximum size of 2112 bytes. By setting the sca_offset to
some unlucky numbers, we exceed the page.
0x7c0 (1984) -> Fits exactly
0x7d0 (2000) -> 16 bytes out
0x7e0 (2016) -> 32 bytes out
0x7f0 (2032) -> 48 bytes out
One VCPU entry is 32 bytes long.
For the last two cases, we actually write data to the other page.
1. The address of the VCPU.
2. Injection/delivery/clearing of SIGP externall calls via SIGP IF.
Especially the 2. happens regularly. So this could produce two problems:
1. The guest losing/getting external calls.
2. Random memory overwrites in the host.
So this problem happens on every 127 + 128 created VM with 64 VCPUs.
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com> Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The number of spatial streams that are derived from chain mask
for 4x4 devices is using wrong bitmask and conditional check.
This is affecting downlink throughput for QCA99x0 devices. Earlier
cfg_tx_chainmask is not filled by default until user configured it
and so get_nss_from_chainmask never be called. This issue is exposed
by recent commit 166de3f1895d ("ath10k: remove supported chain mask").
By default maximum supported chain mask is filled in cfg_tx_chainmask.
Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation") Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current number of spatial streams used by the client is advertised
as a separate IE in assoc request. Use this information to set
the NSS operating mode.
Fixes: 45c9abc059fa ("ath10k: implement more versatile set_bitrate_mask"). Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A kernel built with DEBUG_RO_DATA && !CONFIG_DEBUG_ALIGN_RODATA doesn't
have .text aligned to a page boundary, though fixup_executable works at
page-granularity thanks to its use of create_mapping. If .text is not
page-aligned, the first page it exists in may be marked non-executable,
leading to failures when an attempt is made to execute code in said
page.
This patch upgrades ALIGN_DEBUG_RO and ALIGN_DEBUG_RO_MIN to force page
alignment for DEBUG_RO_DATA && !CONFIG_DEBUG_ALIGN_RODATA kernels,
ensuring that all sections with specific RWX permission requirements are
mapped with the correct permissions.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reported-by: Jeremy Linton <jeremy.linton@arm.com> Reviewed-by: Laura Abbott <laura@labbott.name> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Suzuki Poulose <suzuki.poulose@arm.com> Cc: Will Deacon <will.deacon@arm.com> Fixes: da141706aea52c1a ("arm64: add better page protections to arm64") Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For reasons not entirely apparent, but now enshrined in history, the
architectural mapping of AArch32 banked registers to AArch64 registers
actually orders SP_<mode> and LR_<mode> backwards compared to the
intuitive r13/r14 order, for all modes except FIQ.
Fix the compat_<reg>_<mode> macros accordingly, in the hope of avoiding
subtle bugs with KVM and AArch32 guests.
Signed-off-by: Robin Murphy <robin.murphy@arm.com> Acked-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.
Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
in operating state
- A bus error condition occurs which activates EI interrupt, system is
still suspended which means EI interrupt will be not be handled nor
cleared.
If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.
By simply reading the IR register on start we will clear any previous
conditions that could be present.
Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com> Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 89cbb0638e9b7 introduced support for deferred connection
parameter removal when unpairing by removing them only once an
existing connection gets disconnected. However, it failed to address
the scenario when we're *not* connected and do an unpair operation.
What makes things worse is that most user space BlueZ versions will
first issue a disconnect request and only then unpair, meaning the
buggy code will be triggered every time. This effectively causes the
kernel to resume scanning and reconnect to a device for which we've
removed all keys and GATT database information.
This patch fixes the issue by adding the missing call to the
hci_conn_params_del() function to a branch which handles the case of
no existing connection.
The HIDP specs define an idle-timeout which automatically disconnects a
device. This has always been implemented in the HIDP layer and forced a
synchronous shutdown of the hidp-scheduler. This works just fine, but
lacks a forced disconnect on the underlying l2cap channels. This has been
broken since:
The old session-management always forced an l2cap error on the ctrl/intr
channels when shutting down. The new session-management skips this, as we
don't want to enforce channel policy on the caller. In other words, if
user-space removes an HIDP device, the underlying channels (which are
*owned* and *referenced* by user-space) are still left active. User-space
needs to call shutdown(2) or close(2) to release them.
Unfortunately, this does not work with idle-timeouts. There is no way to
signal user-space that the HIDP layer has been stopped. The API simply
does not support any event-passing except for poll(2). Hence, we restore
old behavior and force EUNATCH on the sockets if the HIDP layer is
disconnected due to idle-timeouts (behavior of explicit disconnects
remains unmodified). User-space can still call
getsockopt(..., SO_ERROR, ...)
..to retrieve the EUNATCH error and clear sk_err. Hence, the channels can
still be re-used (which nobody does so far, though). Therefore, the API
still supports the new behavior, but with this patch it's also compatible
to the old implicit channel shutdown.
Reported-by: Mark Haun <haunma@keteu.org> Reported-by: Luiz Augusto von Dentz <luiz.dentz@gmail.com> Signed-off-by: David Herrmann <dh.herrmann@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds the USB ID for the Sitecom WLA2100. The Windows 10 inf file
was checked to verify that the addition is correct.
Reported-by: Frans van de Wiel <fvdw@fvdw.eu> Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Cc: Frans van de Wiel <fvdw@fvdw.eu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) The done label was in the wrong place so we didn't copy any
information out when there was no command given.
2) We were using PAGE_SIZE as the size of the buffer instead of
"PAGE_SIZE - pos".
3) snprintf() returns the number of characters that would have been
printed if there were enough space. If there was not enough space
(and we had fixed the memory corruption bug #2) then it would result
in an information leak when we do simple_read_from_buffer(). I've
changed it to use scnprintf() instead.
I also removed the initialization at the start of the function, because
I thought it made the code a little more clear.
Fixes: 5e6e3a92b9a4 ('wireless: mwifiex: initial commit for Marvell mwifiex driver') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 68bab8662f49 ("mfd: twl6040: Optional clk32k clock handling")
added clock handling for the 32k clock from palmas-clk. However, that
patch did not consider a typical situation where twl6040 is built-in,
and palmas-clk is a loadable module like we have in omap2plus_defconfig.
If palmas-clk is not loaded before twl6040 probes, we will get a
"clk32k is not handled" warning during booting. This means that any
drivers relying on this clock will mysteriously fail, including
omap5-uevm WLAN and audio.
Note that for WLAN, we probably should also eventually get
the clk32kgaudio for MMC3 directly as that's shared between
audio and WLAN SDIO at least for omap5-uevm. It seems the
WLAN chip cannot get it as otherwise MMC3 won't get properly
probed.
Fixes: 68bab8662f49 ("mfd: twl6040: Optional clk32k clock handling") Signed-off-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch affects the clocks that use fractional ndivider in their
PLL output frequency calculation. Instead of 2^20 divide factor, the
clock's ndiv integer shift was used. Fixed the bug by replacing ndiv
integer shift with 2^20 factor.
Signed-off-by: Simran Rai <ssimran@broadcom.com> Signed-off-by: Ray Jui <rjui@broadcom.com> Reviewed-by: Scott Branden <sbranden@broadcom.com> Fixes: 5fe225c105fd ("clk: iproc: add initial common clock support") Signed-off-by: Michael Turquette <mturquette@baylibre.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So the /proc/PID/stat 'wchan' field (the 30th field, which contains
the absolute kernel address of the kernel function a task is blocked in)
leaks absolute kernel addresses to unprivileged user-space:
seq_put_decimal_ull(m, ' ', wchan);
The absolute address might also leak via /proc/PID/wchan as well, if
KALLSYMS is turned off or if the symbol lookup fails for some reason:
static int proc_pid_wchan(struct seq_file *m, struct pid_namespace *ns,
struct pid *pid, struct task_struct *task)
{
unsigned long wchan;
char symname[KSYM_NAME_LEN];
There's one compatibility quirk here: procps relies on whether the
absolute value is non-zero - and we can provide that functionality
by outputing "0" or "1" depending on whether the task is blocked
(whether there's a wchan address).
These days there appears to be very little legitimate reason
user-space would be interested in the absolute address. The
absolute address is mostly historic: from the days when we
didn't have kallsyms and user-space procps had to do the
decoding itself via the System.map.
So this patch sets all numeric output to "0" or "1" and keeps only
symbolic output, in /proc/PID/wchan.
( The absolute sleep address can generally still be profiled via
perf, by tasks with sufficient privileges. )
In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.
This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: Marcin Wojtas <mw@semihalf.com> Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes a84e32894191 ("net: mvneta: fix refilling for Rx DMA buffers") Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CPU_MAP register is duplicated for each CPUs at different addresses,
each instance being at a different address.
However, the code so far was using CONFIG_NR_CPUS to initialise the CPU_MAP
registers for each registers, while the SoCs embed at most 4 CPUs.
This is especially an issue with multi_v7_defconfig, where CONFIG_NR_CPUS
is currently set to 16, resulting in writes to registers that are not
CPU_MAP.
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add some new PCI IDs for the 8260 series which were missing.
The following sub-system IDs were added:
0x0130, 0x1130, 0x0132, 0x1132, 0x1150, 0x8110, 0x9110, 0x8130,
0x9130, 0x8132, 0x9132, 0x8150, 0x9150, 0x0044, 0x0930
The hardware bug in the commit mentioned below forces us
not to re-enable the clock gating in the Host Cluster.
The impact on the power consumption is minimal and it allows
the WAKE_ME interrupt to propagate.
When sending HCI data over NCI, HCI return code is part
of the NCI data. In order to get correctly the HCI return
code, we assume the NCI communication is successful and
extract the return code for the nci_hci functions return code.
This is done because nci_to_errno does not match hci return
code value.
When sending HCI data over NCI, cmd information should be
present only on the first packet.
Each packet shall be specifically allocated and sent to the
NCI layer.
If parse_acl_data succeeds but the subsequent parsing of smps
attributes fails, there will be a memory leak due to early returns.
Fix that by moving the ACL parsing later.
Fixes: 18998c381b19b ("cfg80211: allow requesting SMPS mode on ap start") Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In TDLS channel-switch operations the chandef can sometimes be NULL.
Avoid an oops in the trace code for these cases and just print a
chandef full of zeros.
The ifmgd->ave_beacon_signal value cannot be taken as is for
comparisons, it must be divided by since it's represented
like that for better accuracy of the EWMA calculations. This
would lead to invalid driver RSSI events. Fix the used value.
I received a bug report that running 32-bit MPX binaries on
64-bit kernels was broken. I traced it down to this little code
snippet. We were switching our "number of bounds directory
entries" calculation correctly. But, we didn't switch the other
side of the calculation: the virtual space size.
This meant that we were calculating an absurd size for
bd_entry_virt_space() on 32-bit because we used the 64-bit
virt_space.
This was _also_ broken for 32-bit kernels running on 64-bit
hardware since boot_cpu_data.x86_virt_bits=48 even when running
in 32-bit mode.
Correct that and properly handle all 3 possible cases:
1. 32-bit binary on 64-bit kernel
2. 64-bit binary on 64-bit kernel
3. 32-bit binary on 32-bit kernel
This manifested in having bounds tables not properly unmapped.
It "leaked" memory but had no functional impact otherwise.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave@sr71.net> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20151111181934.FA7FAC34@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When you call get_user(foo, bar), you effectively do a
copy_from_user(&foo, bar, sizeof(*bar));
Note that the sizeof() is implicit.
When we reach out to userspace to try to zap an entire "bounds
table" we need to go read a "bounds directory entry" in order to
locate the table's address. The size of a "directory entry"
depends on the binary being run and is always the size of a
pointer.
But, when we have a 64-bit kernel and a 32-bit application, the
directory entry is still only 32-bits long, but we fetch it with
a 64-bit pointer which makes get_user() does a 64-bit fetch.
Reading 4 extra bytes isn't harmful, unless we are at the end of
and run off the table. It might also cause the zero page to get
faulted in unnecessarily even if you are not at the end.
Fix it up by doing a special 32-bit get_user() via a cast when
we have 32-bit userspace.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave@sr71.net> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20151111181931.3ACF6822@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(This should have gone to LKML originally. Sorry for the extra
noise, folks on the cc.)
Background:
Signal frames on x86 have two formats:
1. For 32-bit executables (whether on a real 32-bit kernel or
under 32-bit emulation on a 64-bit kernel) we have a
'fpregset_t' that includes the "FSAVE" registers.
2. For 64-bit executables (on 64-bit kernels obviously), the
'fpregset_t' is smaller and does not contain the "FSAVE"
state.
When creating the signal frame, we have to be aware of whether
we are running a 32 or 64-bit executable so we create the
correct format signal frame.
Problem:
save_xstate_epilog() uses 'fx_sw_reserved_ia32' whenever it is
called for a 32-bit executable. This is for real 32-bit and
ia32 emulation.
But, fpu__init_prepare_fx_sw_frame() only initializes
'fx_sw_reserved_ia32' when emulation is enabled, *NOT* for real
32-bit kernels.
This leads to really wierd situations where 32-bit programs
lose their extended state when returning from a signal handler.
The kernel copies the uninitialized (zero) 'fx_sw_reserved_ia32'
out to userspace in save_xstate_epilog(). But when returning
from the signal, the kernel errors out in check_for_xstate()
when it does not see FP_XSTATE_MAGIC1 present (because it was
zeroed). This leads to the FPU/XSAVE state being initialized.
For MPX, this leads to the most permissive state and means we
silently lose bounds violations. I think this would also mean
that we could lose *ANY* FPU/SSE/AVX state. I'm not sure why
no one has spotted this bug.
I believe this was broken by:
72a671ced66d ("x86, fpu: Unify signal handling code paths for x86 and x86_64 kernels")
way back in 2012.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dave@sr71.net Cc: fenghua.yu@intel.com Cc: yu-cheng.yu@intel.com Link: http://lkml.kernel.org/r/20151111002354.A0799571@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KVM uses the get_xsave_addr() function in a different fashion from
the native kernel, in that the 'xsave' parameter belongs to guest vcpu,
not the currently running task.
But 'xsave' is replaced with current task's (host) xsave structure, so
get_xsave_addr() will incorrectly return the bad xsave address to KVM.
Fix it so that the passed in 'xsave' address is used - as intended
originally.
Signed-off-by: Huaitong Han <huaitong.han@intel.com> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: dave.hansen@intel.com Link: http://lkml.kernel.org/r/1446800423-21622-1-git-send-email-huaitong.han@intel.com
[ Tidied up the changelog. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There appears to be no formal statement of what pv_irq_ops.save_fl() is
supposed to return precisely. Native returns the full flags, while lguest and
Xen only return the Interrupt Flag, and both have comments by the
implementations stating that only the Interrupt Flag is looked at. This may
have been true when initially implemented, but no longer is.
To make matters worse, the Xen PVOP leaves the upper bits undefined, making
the BUG_ON() undefined behaviour. Experimentally, this now trips for 32bit PV
guests on Broadwell hardware. The BUG_ON() is consistent for an individual
build, but not consistent for all builds. It has also been a sitting timebomb
since SMAP support was introduced.
Use native_save_fl() instead, which will obtain an accurate view of the AC
flag.
Signed-off-by: Andrew Cooper <andrew.cooper3@citrix.com> Reviewed-by: David Vrabel <david.vrabel@citrix.com> Tested-by: Rusty Russell <rusty@rustcorp.com.au> Cc: Rusty Russell <rusty@rustcorp.com.au> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: <lguest@lists.ozlabs.org> Cc: Xen-devel <xen-devel@lists.xen.org> Link: http://lkml.kernel.org/r/1433323874-6927-1-git-send-email-andrew.cooper3@citrix.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we get loaded by a 64-bit bootloader, kernel entry point is
startup_64 in head_64.S. We don't trust any and all bootloaders because
some will fiddle with CPU configuration so we go ahead and massage each
CPU into sanity again.
For example, some dell BIOSes have this XD disable feature which set
IA32_MISC_ENABLE[34] and disable NX. This might be some dumb workaround
for other OSes but Linux sure doesn't need it.
A similar thing is present in the Surface 3 firmware - see
https://bugzilla.kernel.org/show_bug.cgi?id=106051 - which sets this bit
only on the BSP:
Commit d32932d02e18 ("x86/irq: Convert IOAPIC to use hierarchical irqdomain
interfaces") brought a regression for Hyper-V Gen2 instances. These
instances don't have i8259 legacy PIC but they use legacy IRQs for serial
port, rtc, and acpi. With this commit included we end up with these IRQs
not initialized. Earlier, there was a special workaround for legacy IRQs
in mp_map_pin_to_irq() doing mp_irqdomain_map() without looking at
nr_legacy_irqs() and now we fail in __irq_domain_alloc_irqs() when
irq_domain_alloc_descs() returns -EEXIST.
The essence of the issue seems to be that early_irq_init() calls
arch_probe_nr_irqs() to figure out the number of legacy IRQs before
we probe for i8259 and gets 16. Later when init_8259A() is called we switch
to NULL legacy PIC and nr_legacy_irqs() starts to return 0 but we already
have 16 descs allocated.
Solve the issue by separating i8259 probe from init and calling it in
arch_probe_nr_irqs() before we actually use nr_legacy_irqs() information.
Fixes: d32932d02e18 ("x86/irq: Convert IOAPIC to use hierarchical irqdomain interfaces") Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Link: http://lkml.kernel.org/r/1446543614-3621-1-git-send-email-vkuznets@redhat.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit f5f3497cad8c extended the low identity mapping. However, if
the kernel uses more than 2 GB (VMSPLIT_2G_OPT or VMSPLIT_1G memory
split), the normal memory mapping is overwritten by the low identity
mapping causing a crash. To avoid overwritting, limit the low identity
map to cover only memory before kernel range (PAGE_OFFSET).
Fixes: f5f3497cad8c "x86/setup: Extend low identity map to cover whole kernel range Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Laszlo Ersek <lersek@redhat.com> Cc: Matt Fleming <matt.fleming@intel.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Link: http://lkml.kernel.org/r/1446815916-22105-1-git-send-email-krzysiek@podlesie.net Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 32-bit systems, the initial_page_table is reused by
efi_call_phys_prolog as an identity map to call
SetVirtualAddressMap. efi_call_phys_prolog takes care of
converting the current CPU's GDT to a physical address too.
For PAE kernels the identity mapping is achieved by aliasing the
first PDPE for the kernel memory mapping into the first PDPE
of initial_page_table. This makes the EFI stub's trick "just work".
However, for non-PAE kernels there is no guarantee that the identity
mapping in the initial_page_table extends as far as the GDT; in this
case, accesses to the GDT will cause a page fault (which quickly becomes
a triple fault). Fix this by copying the kernel mappings from
swapper_pg_dir to initial_page_table twice, both at PAGE_OFFSET and at
identity mapping.
For some reason, this is only reproducible with QEMU's dynamic translation
mode, and not for example with KVM. However, even under KVM one can clearly
see that the page table is bogus:
[ It appears that you can skate past this issue if you don't receive
any interrupts while the bogus GDT pointer is loaded, or if you avoid
reloading the segment registers in general.
Andy Lutomirski provides some additional insight:
"AFAICT it's entirely permissible for the GDTR and/or LDT
descriptor to point to unmapped memory. Any attempt to use them
(segment loads, interrupts, IRET, etc) will try to access that memory
as if the access came from CPL 0 and, if the access fails, will
generate a valid page fault with CR2 pointing into the GDT or
LDT."
Up until commit 23a0d4e8fa6d ("efi: Disable interrupts around EFI
calls, not in the epilog/prolog calls") interrupts were disabled
around the prolog and epilog calls, and the functional GDT was
re-installed before interrupts were re-enabled.
Which explains why no one has hit this issue until now. ]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reported-by: Laszlo Ersek <lersek@redhat.com> Cc: <stable@vger.kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Matt Fleming <matt.fleming@intel.com>
[ Updated changelog. ] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was found that a guest can DoS a host by triggering an infinite
stream of "alignment check" (#AC) exceptions. This causes the
microcode to enter an infinite loop where the core never receives
another interrupt. The host kernel panics pretty quickly due to the
effects (CVE-2015-5307).
Signed-off-by: Eric Northup <digitaleric@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b18d5431acc7 ("KVM: x86: fix CR0.CD virtualization") was
technically correct, but it broke OVMF guests by slowing down various
parts of the firmware.
Commit fb279950ba02 ("KVM: vmx: obey KVM_QUIRK_CD_NW_CLEARED") quirked the
first function modified by b18d5431acc7, vmx_get_mt_mask(), for OVMF's
sake. This restored the speed of the OVMF code that runs before
PlatformPei (including the memory intensive LZMA decompression in SEC).
This patch extends the quirk to the second function modified by b18d5431acc7, kvm_set_cr0(). It eliminates the intrusive slowdown that
hits the EFI_MP_SERVICES_PROTOCOL implementation of edk2's
UefiCpuPkg/CpuDxe -- which is built into OVMF --, when CpuDxe starts up
all APs at once for initialization, in order to count them.
We also carry over the kvm_arch_has_noncoherent_dma() sub-condition from
the other half of the original commit b18d5431acc7.
Fixes: b18d5431acc7a2fd22767925f3a6f597aa4bd29e Cc: Jordan Justen <jordan.l.justen@intel.com> Cc: Alex Williamson <alex.williamson@redhat.com> Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com> Tested-by: Janusz Mocek <januszmk6@gmail.com> Signed-off-by: Laszlo Ersek <lersek@redhat.com># Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SDM says that exiting system management mode from 64-bit mode
is invalid, but that would be too good to be true. But actually,
most of the code is already there to support exiting from compat
mode (EFER.LME=1, EFER.LMA=0). Getting all the way from 64-bit
mode to real mode only requires clearing CS.L and CR4.PCIDE.
GET_SMSTATE depends on real mode to ensure that smbase+offset is treated
as a physical address, which has already caused a bug after shuffling
the code. Enforce physical addressing.
Not zeroing EFER means that a 32-bit firmware cannot enter paging mode
without clearing EFER.LME first (which it should not know about).
Yang Zhang from Intel confirmed that the manual is wrong and EFER is
cleared to zero on INIT.
Fixes: d28bc9dd25ce023270d2e039e7c98d38ecbf7758 Cc: Yang Z Zhang <yang.z.zhang@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If either of the memory allocations in kvm_arch_vcpu_create() fail, the
vcpu which has been allocated and kvm_vcpu_init'd doesn't get uninit'd
in the error handling path. Add a call to kvm_vcpu_uninit() to fix this.
Fixes: 669e846e6c4e ("KVM/MIPS32: MIPS arch specific APIs for KVM") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The immediate field of the CACHE instruction is signed, so ensure that
it gets sign extended by casting it to an int16_t rather than just
masking the low 16 bits.
ASID restoration on guest resume should determine the guest execution
mode based on the guest Status register rather than bit 30 of the guest
PC.
Fix the two places in locore.S that do this, loading the guest status
from the cop0 area. Note, this assembly is specific to the trap &
emulate implementation of KVM, so it doesn't need to check the
supervisor bit as that mode is not implemented in the guest.
Fixes: b680f70fc111 ("KVM/MIPS32: Entry point for trampolining to...") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Gleb Natapov <gleb@kernel.org> Cc: linux-mips@linux-mips.org Cc: kvm@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DDR control initialization needs to know the SoC type, however
ath79_detect_sys_type() was called after ath79_ddr_ctrl_init().
Reverse the order to fix the DDR control initialization on ar71xx and
ar934x.
Signed-off-by: Alban Bedel <albeu@free.fr> Cc: Felix Fietkau <nbd@openwrt.org> Cc: Qais Yousef <qais.yousef@imgtec.com> Cc: Andrew Bresticker <abrestic@chromium.org> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11500/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add helper macro builtin_mips_cdmm_driver() for builtin CDMM drivers
that don't do anything special in init and have no exit. The
module_mips_cdmm_driver() helper isn't really appropriate for drivers
that can't be built as a module.
This adds a basic implementation of clk_round_rate()
The clk_round_rate() function is called by multiple drivers and
subsystems now and the lantiq clk driver is supposed to export this,
but doesn't do so, this causes linking problems like this one:
ERROR: "clk_round_rate" [drivers/media/v4l2-core/videodev.ko] undefined!
The z2 machine calls pxa27x_set_pwrmode() in order to power off
the machine, but this function gets discarded early at boot because
it is marked __init, as pointed out by kbuild:
WARNING: vmlinux.o(.text+0x145c4): Section mismatch in reference from the function z2_power_off() to the function .init.text:pxa27x_set_pwrmode()
The function z2_power_off() references
the function __init pxa27x_set_pwrmode().
This is often because z2_power_off lacks a __init
annotation or the annotation of pxa27x_set_pwrmode is wrong.
This removes the __init section modifier to fix rebooting and the
build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: ba4a90a6d86a ("ARM: pxa/z2: fix building error of pxa27x_cpu_suspend() no longer available") Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 99f84cae43df ("ARM: dts: add wl12xx/wl18xx bindings") added
device tree bindings for the TI WLAN SDIO on many omap variants.
I recall wondering how come omap5-uevm did not have the WLAN
added and this issue has been bugging me for a while now, and
I finally tracked it down to a bad pinmux regression, and a missing
deferred probe handling for the 32k clock from palmas that's
requested by twl6040.
Basically 392adaf796b9 ("ARM: dts: omap5-evm: Add mcspi data")
added pin muxing for mcspi4 that conflicts with the onboard
WLAN. While some omap5-uevm don't have WLAN populated, the
pins are not reused for other devices. And as the SDIO bus
should be probed, let's try to enable WLAN by default.
Let's fix the regression and add the WLAN configuration as
done for the other boards in 99f84cae43df ("ARM: dts: add
wl12xx/wl18xx bindings"). And let's use the new MMC pwrseq for
the 32k clock as suggested by Javier Martinez Canillas
<javier@dowhile0.org>.
Note that without a related deferred probe fix for twl6040,
the 32k clock is not initialized if palmas-clk is a module
and twl6040 is built-in.
Let's also use the generic "non-removable" instead of the
legacy "ti,non-removable" property while at it.
And finally, note that omap5 seems to require WAKEUP_EN for
the WLAN GPIO interrupt.
fncpy() requires that the source and the destination are both 8-byte
aligned.
Signed-off-by: Patrick Doyle <pdoyle@irobot.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Fixes: d94e688cae56 ("ARM: at91/pm: move the copying the sram function to the sram initialization phase") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 72daceb9a10a ("net: rfkill: gpio: Add default GPIO driver mappings
for ACPI") removed possibility to request GPIO by table index for non-ACPI
platforms without changing its users. As result "shutdown" GPIO request
will fail if request for "reset" GPIO succeeded or "reset" will be
requested instead of "shutdown" if "reset" wasn't defined. Fix it by
making gpiod_lookup_table use con_id's instead of indexes.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Fixes: 72daceb (net: rfkill: gpio: Add default GPIO driver mappings for ACPI) Acked-by: Alexandre Courbot <acourbot@nvidia.com> Reviewed-by: Marc Dietrich <marvin24@gmx.de> Tested-by: Marc Dietrich <marvin24@gmx.de> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For imx27, it needs three clocks to let the controller work,
the old code is wrong, and usbmisc has not included clock handling
code any more. Without this patch, it will cause below data
abort when accessing usbmisc registers.
usbcore: registered new interface driver usb-storage
Unhandled fault: external abort on non-linefetch (0x008) at 0xf4424600
pgd = c0004000
[f4424600] *pgd=10000452(bad)
Internal error: : 8 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.1.0-next-20150701-dirty #3089
Hardware name: Freescale i.MX27 (Device Tree Support)
task: c7832b60 ti: c783e000 task.ti: c783e000
PC is at usbmisc_imx27_init+0x4c/0xbc
LR is at usbmisc_imx27_init+0x40/0xbc
pc : [<c03cb5c0>] lr : [<c03cb5b4>] psr: 60000093
sp : c783fe08 ip : 00000000 fp : 00000000
r10: c0576434 r9 : 0000009c r8 : c7a773a0
r7 : 01000000 r6 : 60000013 r5 : c7a776f0 r4 : c7a773f0
r3 : f4424600 r2 : 00000000 r1 : 00000001 r0 : 00000001
Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 0005317f Table: a0004000 DAC: 00000017
Process swapper (pid: 1, stack limit = 0xc783e190)
Stack: (0xc783fe08 to 0xc7840000)
IOMMU-based dma_mmap() implementation lacked proper support for offset
parameter used in mmap call (it always assumed that mapping starts from
offset zero). This patch adds support for offset parameter to IOMMU-based
implementation.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_mmap() function in IOMMU-based dma-mapping implementation lacked
a check for valid range of mmap parameters (offset and buffer size), what
might have caused access beyond the allocated buffer. This patch fixes
this issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only cpu seeing dst refcount going to 0 can safely
dereference dst->flags.
Otherwise an other cpu might already have freed the dst.
Fixes: 27b75c95f10d ("net: avoid RCU for NOCACHE dst") Reported-by: Greg Thelen <gthelen@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 7d5cd2ce529b, when bond_enslave fails on devices that
are not ARPHRD_ETHER, if needed, it resets the bonding device back to
ARPHRD_ETHER by calling ether_setup.
Unfortunately, ether_setup clobbers dev->flags, clearing IFF_UP
if the bond device is up, leaving it in a quasi-down state without
having actually gone through dev_close. For bonding, if any periodic
work queue items are active (miimon, arp_interval, etc), those will
remain running, as they are stopped by bond_close. At this point, if
the bonding module is unloaded or the bond is deleted, the system will
panic when the work function is called.
This panic is resolved by calling dev_close on the bond itself
prior to calling ether_setup.
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Fixes: 7d5cd2ce5292 ("bonding: correctly handle bonding type change on enslave failure") Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log