The caller of ndo_start_xmit may not already have called
skb_reset_mac_header. The returned value of skb_mac_header/eth_hdr
therefore can be in the wrong position and even outside the current skbuff.
This for example happens when the user binds to the device using a
PF_PACKET-SOCK_RAW with enabled qdisc-bypass:
int opt = 4;
setsockopt(sock, SOL_PACKET, PACKET_QDISC_BYPASS, &opt, sizeof(opt));
Since eth_hdr is used all over the codebase, the batadv_interface_tx
function must always take care of resetting it.
It is not allowed to use WARN* helpers on potential incorrect input from
the user or transient problems because systems configured as panic_on_warn
will reboot due to such a problem.
A NULL return value of __dev_get_by_index can be caused by various problems
which can either be related to the system configuration or problems
(incorrectly returned network namespaces) in other (virtual) net_device
drivers. batman-adv should not cause a (harmful) WARN in this situation and
instead only report it via a simple message.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface") Reported-by: syzbot+c764de0fcfadca9a8595@syzkaller.appspotmail.com Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check assumes that in transport mode, the first templates family
must match the address family of the policy selector.
Syzkaller managed to build a template using MODE_ROUTEOPTIMIZATION,
with ipv4-in-ipv6 chain, leading to following splat:
BUG: KASAN: stack-out-of-bounds in xfrm_state_find+0x1db/0x1854
Read of size 4 at addr ffff888063e57aa0 by task a.out/2050
xfrm_state_find+0x1db/0x1854
xfrm_tmpl_resolve+0x100/0x1d0
xfrm_resolve_and_create_bundle+0x108/0x1000 [..]
Problem is that addresses point into flowi4 struct, but xfrm_state_find
treats them as being ipv6 because it uses templ->encap_family is used
(AF_INET6 in case of reproducer) rather than family (AF_INET).
This patch inverts the logic: Enforce 'template family must match
selector' EXCEPT for tunnel and BEET mode.
In BEET and Tunnel mode, xfrm_tmpl_resolve_one will have remote/local
address pointers changed to point at the addresses found in the template,
rather than the flowi ones, so no oob read will occur.
con_fault() can transition the connection into STANDBY right after
ceph_con_keepalive() clears STANDBY in clear_standby():
libceph user thread ceph-msgr worker
ceph_con_keepalive()
mutex_lock(&con->mutex)
clear_standby(con)
mutex_unlock(&con->mutex)
mutex_lock(&con->mutex)
con_fault()
...
if KEEPALIVE_PENDING isn't set
set state to STANDBY
...
mutex_unlock(&con->mutex)
set KEEPALIVE_PENDING
set WRITE_PENDING
This triggers warnings in clear_standby() when either ceph_con_send()
or ceph_con_keepalive() get to clearing STANDBY next time.
I don't see a reason to condition queue_con() call on the previous
value of KEEPALIVE_PENDING, so move the setting of KEEPALIVE_PENDING
into the critical section -- unlike WRITE_PENDING, KEEPALIVE_PENDING
could have been a non-atomic flag.
As Jan Kara pointed out, this change was unsafe since it means we lose
the call to sync_mapping_buffers() in the nojournal case. The
original point of the commit was avoid taking the inode mutex (since
it causes a lockdep warning in generic/113); but we need the mutex in
order to call sync_mapping_buffers().
The proposed patch was to fix a syzbot complaint, but the problem can
also demonstrated via "kvm-xfstests -c nojournal generic/113".
Multiple solutions were discused in the e-mail thread, but none have
landed in the kernel as of this writing. Anyway, commit ad211f3e94b314 is absolutely the wrong way to suppress the lockdep, so
revert it.
Fixes: ad211f3e94b314a910d4af03178a0b52a7d1ee0a ("ext4: use ext4_write_inode() when fsyncing w/o a journal") Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain SNB machines (eg. ASUS K53SV) seem to have a broken BIOS
which misprograms the hardware badly when encountering a suitably
high resolution display. The programmed pipe timings are somewhat
bonkers and the DPLL is totally misprogrammed (P divider == 0).
That will result in atomic commit timeouts as apparently the pipe
is sufficiently stuck to not signal vblank interrupts.
IIRC something like this was also observed on some other SNB
machine years ago (might have been a Dell XPS 8300) but a BIOS
update cured it. Sadly looks like this was never fixed for the
ASUS K53SV as the latest BIOS (K53SV.320 11/11/2011) is still
broken.
The quickest way to deal with this seems to be to shut down
the pipe+ports+DPLL. Unfortunately doing this during the
normal sanitization phase isn't quite soon enough as we
already spew several WARNs about the bogus hardware state.
But it's better than hanging the boot for a few dozen seconds.
Since this is limited to a few old machines it doesn't seem
entirely worthwile to try and rework the readout+sanitization
code to handle it more gracefully.
v2: Fix potential NULL deref (kbuild test robot)
Constify has_bogus_dpll_config()
Fixes 9b42c1f179a6, which changed the default route lookup behavior for
tunnel mode SAs in the outbound direction to use the skb mark, whereas
previously mark=0 was used if the output mark was unspecified. In
mark-based routing schemes such as Android’s, this change in default
behavior causes routing loops or lookup failures.
This patch restores the default behavior of using a 0 mark while still
incorporating the skb mark if the SET_MARK (and SET_MARK_MASK) is
specified.
Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/860150
Fixes: 9b42c1f179a6 ("xfrm: Extend the output_mark to support input direction and masking") Signed-off-by: Benedict Wong <benedictwong@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function was unconditionally returning 0, and a caller would have to
rely on the returned fence pointer being NULL to detect errors. However,
the function vmw_execbuf_copy_fence_user() would expect a non-zero error
code in that case and would BUG otherwise.
So make sure we return a proper non-zero error code if the fence pointer
returned is NULL.
if vmw_execbuf_fence_commands() fails, The handle value will be
uninitialized and a bogus fence handle might be copied to user-space.
Cc: <stable@vger.kernel.org> Fixes: 2724b2d54cda: ("drm/vmwgfx: Use new validation interface for the modesetting code v2") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com> Reviewed-by: Brian Paul <brianp@vmware.com> #v1 Reviewed-by: Sinclair Yeh <syeh@vmware.com> #v1 Reviewed-by: Deepak Rawat <drawat@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing break statement in order to prevent the code from falling
through to the default case.
The resoning for this is that pclk_vol_table is an automatic variable.
So, it makes no sense to update it just before falling through to the
default case and return -EINVAL.
This bug was found thanks to the ongoing efforts to enabling
-Wimplicit-fallthrough.
Fixes: cd70f3d6e3fa ("drm/amd/powerplay: PP/DAL interface changes for dynamic clock switch") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update SPDX License Identifier from GPL-2.0+ to GPL-2.0
and drop some GPL text.
This fixes a mismatch between the existing SPDX headers and GPL
boilerplate text.
Fixes: 1f0f01515172 ("Add support for Rockchip Soc RGB output interface") Cc: stable@vger.kernel.org Reported-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sandy Huang <hjc@rock-chips.com> Signed-off-by: Heiko Stuebner <heiko@sntech.de> Link: https://patchwork.freedesktop.org/patch/msgid/1548238479-171491-1-git-send-email-hjc@rock-chips.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers use IEEE80211_KEY_FLAG_SW_MGMT_TX to indicate that management
frames need to be software encrypted. Since normal data packets are still
encrypted by the hardware, crypto_tx_tailroom_needed_cnt gets decremented
after key upload to hw. This can lead to passing skbs to ccmp_encrypt_skb,
which don't have the necessary tailroom for software encryption.
Change the code to add tailroom for encrypted management packets, even if
crypto_tx_tailroom_needed_cnt is 0.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN detects a use-after-free when vop devices are removed.
This problem was introduced by commit 0063e8bbd2b62d136 ("virtio_vop:
don't kfree device on register failure"). That patch moved the freeing
of the struct _vop_vdev to the release function, but failed to ensure
that vop holds a reference to the device when it doesn't want it to go
away. A kfree() was replaced with a put_device() in the unregistration
path, but the last reference to the device is already dropped in
unregister_virtio_device() so the struct is freed before vop is done
with it.
Fix it by holding a reference until cleanup is done. This is similar to
the fix in virtio_pci in commit 2989be09a8a9d6 ("virtio_pci: fix use
after free on release").
==================================================================
BUG: KASAN: use-after-free in vop_scan_devices+0xc6c/0xe50 [vop]
Read of size 8 at addr ffff88800da18580 by task kworker/0:1/12
With support for split pmd lock, we use pmd page pmd_huge_pte pointer
to store the deposited page table. In those config when we move page
tables we need to make sure we move the deposited page table to the
correct pmd page. Otherwise this can result in crash when we withdraw
of deposited page table because we can find the pmd_huge_pte NULL.
When binding an SCM volume to a physical address the hypervisor has the
option to return early with a continue token with the expectation that
the guest will resume the bind operation until it completes. A quirk of
this interface is that the bind address will only be returned by the
first bind h-call and the subsequent calls will return
0xFFFF_FFFF_FFFF_FFFF for the bind address.
We currently do not save the address returned by the first h-call. As a
result we will use the junk address as the base of the bound region if
the hypervisor decides to split the bind across multiple h-calls. This
bug was found when testing with very large SCM volumes where the bind
process would take more time than they hypervisor's internal h-call time
limit would allow. This patch fixes the issue by saving the bind address
from the first call.
Cc: stable@vger.kernel.org Fixes: b5beae5e224f ("powerpc/pseries: Add driver for PAPR SCM regions") Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device/driver model clearly mandates that bus driver that discover
and allocate the device must set the release callback. This callback
will be used to free the device after all references have gone away.
scmi bus driver is missing the obvious callback which will result in
the following warning if the device is unregistered:
Device 'scmi_dev.1' does not have a release() function, it is broken and
must be fixed. See Documentation/kobject.txt.
WARNING at drivers/base/core.c:922 device_release+0x8c/0xa0
Hardware name: ARM LTD Juno Development Platform BIOS EDK II Jan 21 2019
Workqueue: events deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO)
pc : device_release+0x8c/0xa0
lr : device_release+0x8c/0xa0
Call trace:
device_release+0x8c/0xa0
kobject_put+0x8c/0x208
device_unregister+0x30/0x78
scmi_device_destroy+0x28/0x50
scmi_probe+0x354/0x5b0
platform_drv_probe+0x58/0xa8
really_probe+0x2c4/0x3e8
driver_probe_device+0x12c/0x148
__device_attach_driver+0xac/0x150
bus_for_each_drv+0x78/0xd8
__device_attach+0xe0/0x168
device_initial_probe+0x24/0x30
bus_probe_device+0xa0/0xa8
deferred_probe_work_func+0x8c/0xe0
process_one_work+0x1f0/0x478
worker_thread+0x22c/0x450
kthread+0x134/0x138
ret_from_fork+0x10/0x1c
---[ end trace 420bdb7f6af50937 ]---
Fix the issue by providing scmi_device_release callback. We have
everything required for device release already in scmi_device_destroy,
so we just need to move freeing of the device to scmi_device_release.
The timer interrupts specified in commit 3652e2741f42 ("ARM: dts:
da850: Add clocks") are wrong but since the current timer code
hard-codes them, the bug was never spotted.
This patch must go into stable since, once we introduce a proper
clocksource driver, devices with buggy device tree will stop booting.
When generating vdso-o32.lds & vdso-n32.lds for use with programs
running as compat ABIs under 64b kernels, we previously haven't included
the compiler flags that are supposedly common to all ABIs - ie. those in
the ccflags-vdso variable.
This is problematic in cases where we need to provide the -m%-float flag
in order to ensure that we don't attempt to use a floating point ABI
that's incompatible with the target CPU & ABI. For example a toolchain
using current gcc trunk configured --with-fp-32=xx fails to build a
64r6el_defconfig kernel with the following error:
Include $(ccflags-vdso) for the compat VDSO .lds builds, just as it is
included for the native VDSO .lds & when compiling objects for the
compat VDSOs. This ensures we consistently provide the -msoft-float flag
amongst others, avoiding the problem by ensuring we're agnostic to the
toolchain defaults.
Signed-off-by: Paul Burton <paul.burton@mips.com> Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Cc: linux-mips@vger.kernel.org Cc: Kevin Hilman <khilman@baylibre.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Maciej W . Rozycki <macro@linux-mips.org> Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On my Yeeloong 8089, I noticed the machine fails to shutdown
properly, and often, the function mach_prepare_reboot() is
unexpectedly executed, thus the machine reboots instead. A
wait loop is needed to ensure the system is in a well-defined
state before going down.
In commit 997e93d4df16 ("MIPS: Hang more efficiently on
halt/powerdown/restart"), a general superset of the wait loop for all
platforms is already provided, so we don't need to implement our own.
This commit simply removes the unreachable() compiler marco after
mach_prepare_reboot(), thus allowing the execution of machine_hang().
My test shows that the machine is now able to shutdown successfully.
Please note that there are two different bugs preventing the machine
from shutting down, another work-in-progress commit is needed to
fix a lockup in cpufreq / i8259 driver, please read Reference, this
commit does not fix that bug.
Reference: https://lkml.org/lkml/2019/2/5/908 Signed-off-by: Yifeng Li <tomli@tomli.me> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Cc: Huacai Chen <chenhc@lemote.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-kernel@vger.kernel.org Cc: Aaro Koskinen <aaro.koskinen@iki.fi> Cc: stable@vger.kernel.org # v4.17+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MIPS VDSO build currently doesn't provide the -msoft-float flag to
the compiler as the kernel proper does. This results in an attempt to
use the compiler's default floating point configuration, which can be
problematic in cases where this is incompatible with the target CPU's
-march= flag. For example decstation_defconfig fails to build using
toolchains in which gcc was configured --with-fp-32=xx with the
following error:
The kernel proper avoids this error because we build with the
-msoft-float compiler flag, rather than using the compiler's default.
Pass this flag through to the VDSO build so that it too becomes agnostic
to the toolchain's floating point configuration.
Note that this is filtered out from KBUILD_CFLAGS rather than simply
always using -msoft-float such that if we switch the kernel to use
-mno-float in the future the VDSO will automatically inherit the change.
The VDSO doesn't actually include any floating point code, and its
.MIPS.abiflags section is already manually generated to specify that
it's compatible with any floating point ABI. As such this change should
have no effect on the resulting VDSO, apart from fixing the build
failure for affected toolchains.
Signed-off-by: Paul Burton <paul.burton@mips.com> Reported-by: Kevin Hilman <khilman@baylibre.com> Reported-by: Guenter Roeck <linux@roeck-us.net> Tested-by: Kevin Hilman <khilman@baylibre.com>
References: https://lore.kernel.org/linux-mips/1477843551-21813-1-git-send-email-linux@roeck-us.net/
References: https://kernelci.org/build/id/5c4e4ae059b5142a249ad004/logs/ Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Cc: Maciej W. Rozycki <macro@linux-mips.org> Cc: linux-mips@vger.kernel.org Cc: stable@vger.kernel.org # v4.4+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DTC introduced an i2c_bus_reg check in v1.4.7, used since Linux v4.20,
which complains about upper case addresses used in the unit name.
nexys4ddr.dts names an I2C device node "ad7420@4B", leading to:
arch/mips/boot/dts/xilfpga/nexys4ddr.dts:109.16-112.8: Warning
(i2c_bus_reg): /i2c@10A00000/ad7420@4B: I2C bus unit address format
error, expected "4b"
Fix this by switching to lower case addresses throughout the file, as is
*mostly* the case in the file already & fairly standard throughout the
tree.
Accordingly to the documentation
---cut---
The GCR_ERROR_CAUSE.ERR_TYPE field and the GCR_ERROR_MULT.ERR_TYPE
fields can be cleared by either a reset or by writing the current
value of GCR_ERROR_CAUSE.ERR_TYPE to the
GCR_ERROR_CAUSE.ERR_TYPE register.
---cut---
Do exactly this. Original value of cm_error may be safely written back;
it clears error cause and keeps other bits untouched.
Fixes: 3885c2b463f6 ("MIPS: CM: Add support for reporting CM cache errors") Signed-off-by: Vladimir Kondratiev <vladimir.kondratiev@linux.intel.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: linux-mips@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: stable@vger.kernel.org # v4.3+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When printing multiple uprobe arguments as strings the output for the
earlier arguments would also include all later string arguments.
This is best explained in an example:
Consider adding a uprobe to a function receiving two strings as
parameters which is at offset 0xa0 in strlib.so and we want to print
both parameters when the uprobe is hit (on x86_64):
Note the extra "bar" printed as part of arg1. This behaviour stacks up
for additional string arguments.
The strings are stored in a dynamically growing part of the uprobe
buffer by fetch_store_string() after copying them from userspace via
strncpy_from_user(). The return value of strncpy_from_user() is then
directly used as the required size for the string. However, this does
not take the terminating null byte into account as the documentation
for strncpy_from_user() cleary states that it "[...] returns the
length of the string (not including the trailing NUL)" even though the
null byte will be copied to the destination.
Therefore, subsequent calls to fetch_store_string() will overwrite
the terminating null byte of the most recently fetched string with
the first character of the current string, leading to the
"accumulation" of strings in earlier arguments in the output.
Fix this by incrementing the return value of strncpy_from_user() by
one if we did not hit the maximum buffer size.
The H6 main pin controller has four banks of interrupt-triggering pins.
The driver as originally submitted only specified three, but had pin
descriptions referencing a fourth bank. This results in a out-of-bounds
access into .irq_array of struct sunxi_pinctrl. This however did not
result in a crash until v4.20, with commit a66d972465d1 ("devres: Align
data[] to ARCH_KMALLOC_MINALIGN"), which changed the alignment of memory
region returned by devm_kcalloc(). The increase likely moved the
out-of-bounds access into the next, unmapped page.
With KASAN on, the bug is quite clear:
BUG: KASAN: slab-out-of-bounds in sunxi_pinctrl_init_with_variant+0x49c/0x12b8
Write of size 4 at addr ffff80002c680280 by task swapper/0/1
Memory state around the buggy address: ffff80002c680180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff80002c680200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff80002c680280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff80002c680300: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff80002c680380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
Correct the number of IRQ banks so there are no more mismatches.
Fixes: c8a830904991 ("pinctrl: sunxi: add support for the Allwinner H6 main pin controller") Cc: <stable@vger.kernel.org> Signed-off-by: Chen-Yu Tsai <wens@csie.org> Tested-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two and a half years ago, the client was changed to use gathered
Send for larger inline messages, in commit 655fec6987b ("xprtrdma:
Use gathered Send for large inline messages"). Several fixes were
required because there are a few in-kernel device drivers whose
max_sge is 3, and these were broken by the change.
Apparently my memory is going, because some time later, I submitted
commit 25fd86eca11c ("svcrdma: Don't overrun the SGE array in
svc_rdma_send_ctxt"), and after that, commit f3c1fd0ee294 ("svcrdma:
Reduce max_send_sges"). These too incorrectly assumed in-kernel
device drivers would have more than a few Send SGEs available.
The fix for the server side is not the same. This is because the
fundamental problem on the server is that, whether or not the client
has provisioned a chunk for the RPC reply, the server must squeeze
even the most complex RPC replies into a single RDMA Send. Failing
in the send path because of Send SGE exhaustion should never be an
option.
Therefore, instead of failing when the send path runs out of SGEs,
switch to using a bounce buffer mechanism to handle RPC replies that
are too complex for the device to send directly. That allows us to
remove the max_sge check to enable drivers with small max_sge to
work again.
Reported-by: Don Dutile <ddutile@redhat.com> Fixes: 25fd86eca11c ("svcrdma: Don't overrun the SGE array in ...") Cc: stable@vger.kernel.org Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
debugfs_rename() needs to check that the dentries passed into it really
are valid, as sometimes they are not (i.e. if the return value of
another debugfs call is passed into this one.) So fix this up by
properly checking if the two parent directories are errors (they are
allowed to be NULL), and if the dentry to rename is not NULL or an
error.
Since we now prevent regulatory restore during STA disconnect
if concurrent AP interfaces are active, we need to reschedule
this check when the AP state changes. This fixes never doing
a restore when an AP is the last interface to stop. Or to put
it another way: we need to re-check after anything we check
here changes.
Cc: stable@vger.kernel.org Fixes: 113f3aaa81bd ("cfg80211: Prevent regulatory restore during STA disconnect in concurrent interfaces") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently syzkaller was able to create unkillablle processes by
creating a timer that is delivered as a thread local signal on SIGHUP,
and receiving SIGHUP SA_NODEFERER. Ultimately causing a loop failing
to deliver SIGHUP but always trying.
When the stack overflows delivery of SIGHUP fails and force_sigsegv is
called. Unfortunately because SIGSEGV is numerically higher than
SIGHUP next_signal tries again to deliver a SIGHUP.
From a quality of implementation standpoint attempting to deliver the
timer SIGHUP signal is wrong. We should attempt to deliver the
synchronous SIGSEGV signal we just forced.
We can make that happening in a fairly straight forward manner by
instead of just looking at the signal number we also look at the
si_code. In particular for exceptions (aka synchronous signals) the
si_code is always greater than 0.
That still has the potential to pick up a number of asynchronous
signals as in a few cases the same si_codes that are used
for synchronous signals are also used for asynchronous signals,
and SI_KERNEL is also included in the list of possible si_codes.
Still the heuristic is much better and timer signals are definitely
excluded. Which is enough to prevent all known ways for someone
sending a process signals fast enough to cause unexpected and
arguably incorrect behavior.
Recently syzkaller was able to create unkillablle processes by
creating a timer that is delivered as a thread local signal on SIGHUP,
and receiving SIGHUP SA_NODEFERER. Ultimately causing a loop
failing to deliver SIGHUP but always trying.
Upon examination it turns out part of the problem is actually most of
the solution. Since 2.5 signal delivery has found all fatal signals,
marked the signal group for death, and queued SIGKILL in every threads
thread queue relying on signal->group_exit_code to preserve the
information of which was the actual fatal signal.
The conversion of all fatal signals to SIGKILL results in the
synchronous signal heuristic in next_signal kicking in and preferring
SIGHUP to SIGKILL. Which is especially problematic as all
fatal signals have already been transformed into SIGKILL.
Instead of dequeueing signals and depending upon SIGKILL to
be the first signal dequeued, first test if the signal group
has already been marked for death. This guarantees that
nothing in the signal queue can prevent a process that needs
to exit from exiting.
Since 2.5.34 the code has had the potential to not allocate siginfo
for SIGSTOP signals. Except for ptrace this is perfectly fine as only
ptrace can use PTRACE_PEEK_SIGINFO and see what the contents of
the delivered siginfo are.
Users of PTRACE_PEEK_SIGINFO that care about the contents siginfo
for SIGSTOP are rare, but they do exist. A seccomp self test
has cared and lldb cares.
Jack Andersen <jackoalan@gmail.com> writes:
> The patch titled
> `signal: Never allocate siginfo for SIGKILL or SIGSTOP`
> created a regression for users of PTRACE_GETSIGINFO needing to
> discern signals that were raised via the tgkill syscall.
>
> A notable user of this tgkill+ptrace combination is lldb while
> debugging a multithreaded program. Without the ability to detect a
> SIGSTOP originating from tgkill, lldb does not have a way to
> synchronize on a per-thread basis and falls back to SIGSTOP-ing the
> entire process.
Everyone affected by this please note. The kernel can still fail to
allocate a siginfo structure. The allocation is with GFP_KERNEL and
is best effort only. If memory is tight when the signal allocation
comes in this will fail to allocate a siginfo.
So I strongly recommend looking at more robust solutions for
synchronizing with a single thread such as PTRACE_INTERRUPT. Or if
that does not work persuading your friendly local kernel developer to
build the interface you need.
Reported-by: Tycho Andersen <tycho@tycho.ws> Reported-by: Kees Cook <keescook@chromium.org> Reported-by: Jack Andersen <jackoalan@gmail.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Reviewed-by: Christian Brauner <christian@brauner.io> Cc: stable@vger.kernel.org Fixes: f149b3155744 ("signal: Never allocate siginfo for SIGKILL or SIGSTOP") Fixes: 6dfc88977e42 ("[PATCH] shared thread signals")
History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per Jonathan Cameron, the buffer needs to allocate room for a
64 bit timestamp as well as the channels. Change the buffer
to allocate this additional space.
Fixes: 2a86487786b5c ("iio: adc: ti-ads8688: add trigger and buffer support") Signed-off-by: Dan Murphy <dmurphy@ti.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to this commit there were 3 issues with our handling of the TS-pin:
1) There are 2 ways how the firmware can disable monitoring of the TS-pin
for designs which do not have a temperature-sensor for the battery:
a) Clearing bit 0 of the AXP20X_ADC_EN1 register
b) Setting bit 2 of the AXP288_ADC_TS_PIN_CTRL monitoring
Prior to this commit we were unconditionally setting both bits to the
value used on devices with a TS. This causes the temperature protection to
kick in on devices without a TS, such as the Jumper ezbook v2, causing
them to not charge under Linux.
This commit fixes this by using regmap_update_bits when updating these 2
registers, leaving the 2 mentioned bits alone.
The next 2 problems are related to our handling of the current-source
for the TS-pin. The current-source used for the battery temp-sensor (TS)
is shared with the GPADC. For proper fuel-gauge and charger operation the
TS current-source needs to be permanently on. But to read the GPADC we
need to temporary switch the TS current-source to ondemand, so that the
GPADC can use it, otherwise we will always read an all 0 value.
2) Problem 2 is we were writing hardcoded values to the ADC TS pin-ctrl
register, overwriting various other unrelated bits. Specifically we were
overwriting the current-source setting for the TS and GPIO0 pins, forcing
it to 80ųA independent of its original setting. On a Chuwi Vi10 tablet
this was causing us to get a too high adc value (due to a too high
current-source) resulting in the following errors being logged:
ACPI Error: AE_ERROR, Returned by Handler for [UserDefinedRegion]
ACPI Error: Method parse/execution failed \_SB.SXP1._TMP, AE_ERROR
This commit fixes this by using regmap_update_bits to change only the
relevant bits.
3) After reading the GPADC channel we were unconditionally enabling the
TS current-source even on devices where the TS-pin is not used and the
current-source thus was off before axp288_adc_read_raw call.
This commit fixes this by making axp288_adc_set_ts a nop on devices where
the ADC is not enabled for the TS-pin.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1610545 Fixes: 3091141d7803 ("iio: adc: axp288: Fix the GPADC pin ...") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, num_loops is unsigned, but it's set by strtoll, which returns a
(signed) long long int. This could lead to overflow, and it also makes the
check "num_loops < 0" always be false, since num_loops is unsigned.
Setting num_loops to -1 to loop forever is almost working because num_loops
is getting set to a very high number, but it's technically still incorrect.
Fix this issue by making num_loops signed. This also fixes an error found
by Smatch.
Signed-off-by: Martin Kelly <mkelly@xevo.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 55dda0abcf9d ("tools: iio: iio_generic_buffer: allow continuous looping") Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We've received a bugreport that using LPM with a SAMSUNG
MZ7TE512HMHP-000L1 SSD leads to system instability, we already have
a quirk for the MZ7TD256HAFV-000L9, which is also a Samsun EVO 840 /
PM851 OEM model, so it seems some of these models have a LPM issue.
This commits adds a NOLPM quirk for the model string from the new
bugeport, to avoid the reported stability issues.
Cc: stable@vger.kernel.org BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1571330 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable BCH soft reset according to MX23 erratum #2847 ("BCH soft
reset may cause bus master lock up") for MX28 too. It has the same
problem.
Observed problem: once per 100,000+ MX28 reboots NAND read failed on
DMA timeout errors:
[ 1.770823] UBI: attaching mtd3 to ubi0
[ 2.768088] gpmi_nand: DMA timeout, last DMA :1
[ 3.958087] gpmi_nand: BCH timeout, last DMA :1
[ 4.156033] gpmi_nand: Error in ECC-based read: -110
[ 4.161136] UBI warning: ubi_io_read: error -110 while reading 64
bytes from PEB 0:0, read only 0 bytes, retry
[ 4.171283] step 1 error
[ 4.173846] gpmi_nand: Chip: 0, Error -1
Without BCH soft reset we successfully executed 1,000,000 MX28 reboots.
I have a quote from NXP regarding this problem, from July 18th 2016:
"As the i.MX23 and i.MX28 are of the same generation, they share many
characteristics. Unfortunately, also the erratas may be shared.
In case of the documented erratas and the workarounds, you can also
apply the workaround solution of one device on the other one. This have
been reported, but I’m afraid that there are not an estimated date for
updating the Errata documents.
Please accept our apologies for any inconveniences this may cause."
The manufacturer specific initialization has already been done when
block unlocking takes place, and if anything goes wrong during this
procedure we should call spinand_manufacturer_cleanup().
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like PROGRAM LOAD (AKA write cache) does not necessarily reset
the cache content to 0xFF (depends on vendor implementation), so we
must fill the page cache entirely even if we only want to program the
data portion of the page, otherwise we might corrupt the BBM or user
data previously programmed in OOB area.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs") Reported-by: Stefan Roese <sr@denx.de> Cc: <stable@vger.kernel.org> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Tested-by: Stefan Roese <sr@denx.de> Reviewed-by: Stefan Roese <sr@denx.de> Acked-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 33f45c44d68b ("mtd: Do not allow MTD devices with inconsistent
erase properties") introduced a check to make sure ->erasesize and
->_erase values are consistent with the MTD_NO_ERASE flag.
This patch did not take the 0 bytes partition case into account which
can happen when the defined partition is outside the flash device memory
range. Fix that by setting the partition erasesize to the parent
erasesize.
Fixes: 33f45c44d68b ("mtd: Do not allow MTD devices with inconsistent erase properties") Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: <stable@vger.kernel.org> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Boris Brezillon <bbrezillon@kernel.org> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the parameter 'count' is non-zero, nfsd4_clone_file_range() will
currently clobber all errors returned by vfs_clone_file_range() and
replace them with EINVAL.
Fixes: 42ec3d4c0218 ("vfs: make remap_file_range functions take and...") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Cc: stable@vger.kernel.org # v4.20+ Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 448a5a552f336bd7b847b1951 ("drivers: base: cacheinfo: use OF
property_read_u32 instead of get_property,read_number") makes cache
size and number_of_sets be 0 if DT doesn't provide there values. I
think this is unreasonable so make them keep the old values, which is
the same as old kernels.
Fixes: 448a5a552f33 ("drivers: base: cacheinfo: use OF property_read_u32 instead of get_property,read_number") Cc: stable@vger.kernel.org Signed-off-by: Huacai Chen <chenhc@lemote.com> Reviewed-by: Sudeep Holla <sudeep.holla@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since IRQs might be muxed on some parts, we need to pay attention when we
are freeing them.
Otherwise we get the ugly WARNING "Trying to free already-free IRQ 20".
Fixes: 628c534ae735 ("serial: sh-sci: Improve support for separate TEI and DRI interrupts") Cc: stable <stable@vger.kernel.org> Signed-off-by: Chris Brandt <chris.brandt@renesas.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There still is a race window after the commit b027e2298bd588
("tty: fix data race between tty_init_dev and flush of buf"),
and we encountered this crash issue if receive_buf call comes
before tty initialization completes in tty_open and
tty->driver_data may be NULL.
it can be fixed by extending ldisc semaphore lock in tty_init_dev
to driver_data initialized completely after tty->ops->open(), but
this will lead to get lock on one function and unlock in some other
function, and hard to maintain, so fix this race only by checking
tty->driver_data when receiving, and return if tty->driver_data
is NULL, and n_tty_receive_buf_common maybe calls uart_unthrottle,
so add the same check.
Because the tty layer knows nothing about the driver associated with the
device, the tty layer can not do anything here, it is up to the tty
driver itself to check for this type of race. Fix up the serial driver
to correctly check to see if it is finished binding with the device when
being called, and if not, abort the tty calls.
[Description and problem report and testing from Li RongQing, I rewrote
the patch to be in the serial layer, not in the tty core - gregkh]
Reported-by: Li RongQing <lirongqing@baidu.com> Tested-by: Li RongQing <lirongqing@baidu.com> Signed-off-by: Wang Li <wangli39@baidu.com> Signed-off-by: Zhang Yu <zhangyu31@baidu.com> Signed-off-by: Li RongQing <lirongqing@baidu.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Notice that the use of the bitwise OR operator '|' always leads to true
in this particular case, which seems a bit suspicious due to the context
in which this expression is being used.
Fix this by using bitwise AND operator '&' instead.
This bug was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@vger.kernel.org Fixes: 6a6cd11d4e57 ("perf test: Add test for the sched tracepoint format fields") Link: http://lkml.kernel.org/r/20190122233439.GA5868@embeddedor Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The perf tool uses /proc/sys/kernel/perf_event_mlock_kb to determine how
large its ringbuffer mmap should be. This can be configured to arbitrary
values, which can be larger than the maximum possible allocation from
kmalloc.
When this is configured to a suitably large value (e.g. thanks to the
perf fuzzer), attempting to use perf record triggers a WARN_ON_ONCE() in
__alloc_pages_nodemask():
WARNING: CPU: 2 PID: 5666 at mm/page_alloc.c:4511 __alloc_pages_nodemask+0x3f8/0xbc8
Let's avoid this by checking that the requested allocation is possible
before calling kzalloc.
Reported-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20190110142745.25495-1-mark.rutland@arm.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Internal injection testing crashed with a console log that said:
mce: [Hardware Error]: CPU 7: Machine Check Exception: f Bank 0: bd80000000100134
This caused a lot of head scratching because the MCACOD (bits 15:0) of
that status is a signature from an L1 data cache error. But Linux says
that it found it in "Bank 0", which on this model CPU only reports L1
instruction cache errors.
The answer was that Linux doesn't initialize "m->bank" in the case that
it finds a fatal error in the mce_no_way_out() pre-scan of banks. If
this was a local machine check, then this partially initialized struct
mce is being passed to mce_panic().
Fix is simple: just initialize m->bank in the case of a fatal error.
Fixes: 40c36e2741d7 ("x86/mce: Fix incorrect "Machine check from unknown source" message") Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vishal Verma <vishal.l.verma@intel.com> Cc: x86-ml <x86@kernel.org> Cc: stable@vger.kernel.org # v4.18 Note pre-v5.0 arch/x86/kernel/cpu/mce/core.c was called arch/x86/kernel/cpu/mcheck/mce.c Link: https://lkml.kernel.org/r/20190201003341.10638-1-tony.luck@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
intel_pmu_cpu_prepare() allocated memory for ->shared_regs among other
members of struct cpu_hw_events. This memory is released in
intel_pmu_cpu_dying() which is wrong. The counterpart of the
intel_pmu_cpu_prepare() callback is x86_pmu_dead_cpu().
Otherwise if the CPU fails on the UP path between CPUHP_PERF_X86_PREPARE
and CPUHP_AP_PERF_X86_STARTING then it won't release the memory but
allocate new memory on the next attempt to online the CPU (leaking the
old memory).
Also, if the CPU down path fails between CPUHP_AP_PERF_X86_STARTING and
CPUHP_PERF_X86_PREPARE then the CPU will go back online but never
allocate the memory that was released in x86_pmu_dying_cpu().
Make the memory allocation/free symmetrical in regard to the CPU hotplug
notifier by moving the deallocation to intel_pmu_cpu_dead().
This started in commit:
a7e3ed1e47011 ("perf: Add support for supplementary event registers").
In principle the bug was introduced in v2.6.39 (!), but it will almost
certainly not backport cleanly across the big CPU hotplug rewrite between v4.7-v4.15...
Reported-by: He Zhe <zhe.he@windriver.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> # With developer hat on Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> # With maintainer hat on Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: acme@kernel.org Cc: bp@alien8.de Cc: hpa@zytor.com Cc: jolsa@kernel.org Cc: kan.liang@linux.intel.com Cc: namhyung@kernel.org Cc: <stable@vger.kernel.org> Fixes: a7e3ed1e47011 ("perf: Add support for supplementary event registers"). Link: https://lkml.kernel.org/r/20181219165350.6s3jvyxbibpvlhtq@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some PCI uncore PMUs cannot be registered on an 8-socket system (HPE
Superdome Flex).
To understand which Socket the PCI uncore PMUs belongs to, perf retrieves
the local Node ID of the uncore device from CPUNODEID(0xC0) of the PCI
configuration space, and the mapping between Socket ID and Node ID from
GIDNIDMAP(0xD4). The Socket ID can be calculated accordingly.
The local Node ID is only available at bit 2:0, but current code doesn't
mask it. If a BIOS doesn't clear the rest of the bits, an incorrect Node ID
will be fetched.
Filter the Node ID by adding a mask.
Reported-by: Song Liu <songliubraving@fb.com> Tested-by: Song Liu <songliubraving@fb.com> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> # v3.7+ Fixes: 7c94ee2e0917 ("perf/x86: Add Intel Nehalem and Sandy Bridge-EP uncore support") Link: https://lkml.kernel.org/r/1548600794-33162-1-git-send-email-kan.liang@linux.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS")
... the hotplug code attempted to detect when SMT was disabled by BIOS,
in which case it reported SMT as permanently disabled. However, that
code broke a virt hotplug scenario, where the guest is booted with only
primary CPU threads, and a sibling is brought online later.
The problem is that there doesn't seem to be a way to reliably
distinguish between the HW "SMT disabled by BIOS" case and the virt
"sibling not yet brought online" case. So the above-mentioned commit
was a bit misguided, as it permanently disabled SMT for both cases,
preventing future virt sibling hotplugs.
Going back and reviewing the original problems which were attempted to
be solved by that commit, when SMT was disabled in BIOS:
1) /sys/devices/system/cpu/smt/control showed "on" instead of
"notsupported"; and
2) vmx_vm_init() was incorrectly showing the L1TF_MSG_SMT warning.
I'd propose that we instead consider #1 above to not actually be a
problem. Because, at least in the virt case, it's possible that SMT
wasn't disabled by BIOS and a sibling thread could be brought online
later. So it makes sense to just always default the smt control to "on"
to allow for that possibility (assuming cpuid indicates that the CPU
supports SMT).
The real problem is #2, which has a simple fix: change vmx_vm_init() to
query the actual current SMT state -- i.e., whether any siblings are
currently online -- instead of looking at the SMT "control" sysfs value.
So fix it by:
a) reverting the original "fix" and its followup fix:
b) changing vmx_vm_init() to query the actual current SMT state --
instead of the sysfs control value -- to determine whether the L1TF
warning is needed. This also requires the 'sched_smt_present'
variable to exported, instead of 'cpu_smt_control'.
Fixes: 73d5e2b47264 ("cpu/hotplug: detect SMT disabled by BIOS") Reported-by: Igor Mammedov <imammedo@redhat.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Joe Mario <jmario@redhat.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/e3a85d585da28cc333ecbc1e78ee9216e6da9396.1548794349.git.jpoimboe@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple code paths where an hrtimer may have been started to
emulate an L1 VMX preemption timer that can result in a call to free_nested
without an intervening L2 exit where the hrtimer is normally
cancelled. Unconditionally cancel in free_nested to cover all cases.
Embargoed until Feb 7th 2019.
Signed-off-by: Peter Shier <pshier@google.com> Reported-by: Jim Mattson <jmattson@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Reported-by: Felix Wilhelm <fwilhelm@google.com> Cc: stable@kernel.org
Message-Id: <20181011184646.154065-1-pshier@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. creates a device that holds a reference to the VM object (with a borrowed
reference, the VM's refcount has not been bumped yet)
2. initializes the device
3. transfers the reference to the device to the caller's file descriptor table
4. calls kvm_get_kvm() to turn the borrowed reference to the VM into a real
reference
The ownership transfer in step 3 must not happen before the reference to the VM
becomes a proper, non-borrowed reference, which only happens in step 4.
After step 3, an attacker can close the file descriptor and drop the borrowed
reference, which can cause the refcount of the kvm object to drop to zero.
This means that we need to grab a reference for the device before
anon_inode_getfd(), otherwise the VM can disappear from under us.
Emulation of certain instructions (VMXON, VMCLEAR, VMPTRLD, VMWRITE with
memory operand, INVEPT, INVVPID) can incorrectly inject a page fault
when passed an operand that points to an MMIO address. The page fault
will use uninitialized kernel stack memory as the CR2 and error code.
The right behavior would be to abort the VM with a KVM_EXIT_INTERNAL_ERROR
exit to userspace; however, it is not an easy fix, so for now just
ensure that the error code and CR2 are zero.
Embargoed until Feb 7th 2019.
Reported-by: Felix Wilhelm <fwilhelm@google.com> Cc: stable@kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the PCI code had recently added a file named 'revision' to every
PCI device. Fix this by renaming the aic94xx revision file to
aic_revision. This is safe to do for us because as far as I can tell,
there's nothing in userspace relying on the current aic94xx revision file
so it can be renamed without breaking anything.
Fixes: 702ed3be1b1b (PCI: Create revision file in sysfs) Cc: stable@vger.kernel.org Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Presently when an error is encountered during probe of the cxlflash
adapter, a deadlock is seen with cpu thread stuck inside
cxlflash_remove(). Below is the trace of the deadlock as logged by
khungtaskd:
cxlflash 0006:00:00.0: cxlflash_probe: init_afu failed rc=-16
INFO: task kworker/80:1:890 blocked for more than 120 seconds.
Not tainted 5.0.0-rc4-capi2-kexec+ #2
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/80:1 D 0 890 2 0x00000808
Workqueue: events work_for_cpu_fn
Call Trace:
0x4d72136320 (unreliable)
__switch_to+0x2cc/0x460
__schedule+0x2bc/0xac0
schedule+0x40/0xb0
cxlflash_remove+0xec/0x640 [cxlflash]
cxlflash_probe+0x370/0x8f0 [cxlflash]
local_pci_probe+0x6c/0x140
work_for_cpu_fn+0x38/0x60
process_one_work+0x260/0x530
worker_thread+0x280/0x5d0
kthread+0x1a8/0x1b0
ret_from_kernel_thread+0x5c/0x80
INFO: task systemd-udevd:5160 blocked for more than 120 seconds.
The deadlock occurs as cxlflash_remove() is called from cxlflash_probe()
without setting 'cxlflash_cfg->state' to STATE_PROBED and the probe thread
starts to wait on 'cxlflash_cfg->reset_waitq'. Since the device was never
successfully probed the 'cxlflash_cfg->state' never changes from
STATE_PROBING hence the deadlock occurs.
We fix this deadlock by setting the variable 'cxlflash_cfg->state' to
STATE_PROBED in case an error occurs during cxlflash_probe() and just
before calling cxlflash_remove().
Cc: stable@vger.kernel.org Fixes: c21e0bbfc485("cxlflash: Base support for IBM CXL Flash Adapter") Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit bf5054569653 ("block: Introduce blk_revalidate_disk_zones()")
inadvertently broke the message output of sd_zbc_print_zones() because the
zone information initialization of the scsi disk structure was moved to the
second scan run while sd_zbc_print_zones() is called on the first
scan. This leads to the following incorrect message to be printed for any
ZBC or ZAC zoned disks.
"...[sdX] 4294967295 zones of 0 logical blocks + 1 runt zone"
Fix this by initializing sdkp zone size and number of zones early on the
first scan. This does not impact the execution of
blk_revalidate_zones(). This functions is still called only once the block
device capacity is set on the second revalidate run on boot, or if the disk
zone configuration changed (i.e. the disk changed).
Fixes: bf5054569653 ("block: Introduce blk_revalidate_disk_zones()") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The send_xchar() and tiocmset() tty operations are optional. Add the
missing sanity checks to prevent user-space triggerable NULL-pointer
dereferences.
Fixes: 6b9ad1c742bf ("staging: speakup: add send_xchar, tiocmset and input functionality for tty") Cc: stable <stable@vger.kernel.org> # 4.13 Cc: Okash Khawaja <okash.khawaja@gmail.com> Cc: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling short packets (length < max packet size) in the Inventra DMA
engine in the MUSB driver causes the MUSB DMA controller to hang. An
example of a problem that is caused by this problem is when streaming
video out of a UVC gadget, only the first video frame is transferred.
For short packets (mode-0 or mode-1 DMA), MUSB_TXCSR_TXPKTRDY must be
set manually by the driver. This was previously done in musb_g_tx
(musb_gadget.c), but incorrectly (all csr flags were cleared, and only
MUSB_TXCSR_MODE and MUSB_TXCSR_TXPKTRDY were set). Fixing that problem
allows some requests to be transferred correctly, but multiple requests
were often put together in one USB packet, and caused problems if the
packet size was not a multiple of 4. Instead, set MUSB_TXCSR_TXPKTRDY
in dma_controller_irq (musbhsdma.c), just like host mode transfers.
This topic was originally tackled by Nicolas Boichat [0] [1] and is
discussed further at [2] as part of his GSoC project [3].
power off the phy should be done before populate the phy. Otherwise,
am335x_init() could be called by the phy owner to power on the phy first,
then am335x_phy_probe() turns off the phy again without the caller knowing
it.
Fixes: 2fc711d76352 ("usb: phy: am335x: Enable USB remote wakeup using PHY wakeup") Cc: stable@vger.kernel.org # v3.18+ Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, AXP803 driver assumes that reg_drivevbus is input which is
wrong. Unfortunate consequence of that is that none of the USB ports
work on the board, even USB HOST port, because USB PHY driver probing
fails due to missing regulator.
Fix that by adding "x-powers,drive-vbus-en" property to AXP803 node.
Fixes: 14ff5d8f9151 ("arm64: dts: allwinner: a64: Orange Pi Win: Enable USB OTG socket") Cc: stable@vger.kernel.org Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On systems or VMs where multiple devices share a single DevID
(because they sit behind a PCI bridge, or because the HW is
broken in funky ways), we reuse the save its_device structure
in order to reflect this.
It turns out that there is a distinct lack of locking when looking
up the its_device, and two device being probed concurrently can result
in double allocations. That's obviously not nice.
A solution for this is to have a per-ITS mutex that serializes device
allocation.
A similar issue exists on the freeing side, which can run concurrently
with the allocation. On top of now taking the appropriate lock, we
also make sure that a shared device is never freed, as we have no way
to currently track the life cycle of such object.
commit 56222b212e8e ("futex: Drop hb->lock before enqueueing on the
rtmutex") changed the locking rules in the futex code so that the hash
bucket lock is not longer held while the waiter is enqueued into the
rtmutex wait list. This made the lock and the unlock path symmetric, but
unfortunately the possible early exit from __rt_mutex_proxy_start() due to
a detected deadlock was not updated accordingly. That allows a concurrent
unlocker to observe inconsitent state which triggers the warning in the
unlock path.
The problem is caused by the remove(rtmutex_waiter) in the failure case of
__rt_mutex_proxy_start() as this lets the unlocker observe a waiter in the
hash bucket but no waiter on the rtmutex, i.e. inconsistent state.
The original commit handles this correctly for the other early return cases
(timeout, signal) by delaying the removal of the rtmutex waiter until the
returning task reacquired the hash bucket lock.
Treat the failure case of __rt_mutex_proxy_start() in the same way and let
the existing cleanup code handle the eventual handover of the rtmutex
gracefully. The regular rt_mutex_proxy_start() gains the rtmutex waiter
removal for the failure case, so that the other callsites are still
operating correctly.
Add proper comments to the code so all these details are fully documented.
Thanks to Peter for helping with the analysis and writing the really
valuable code comments.
Fixes: 56222b212e8e ("futex: Drop hb->lock before enqueueing on the rtmutex") Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com> Co-developed-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> Cc: linux-s390@vger.kernel.org Cc: Stefan Liebler <stli@linux.ibm.com> Cc: Sebastian Sewior <bigeasy@linutronix.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1901292311410.1950@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once the "ld_queue" list is not empty, next descriptor will migrate
into "ld_active" list. The "desc" variable will be overwritten
during that transition. And later the dmaengine_desc_get_callback_invoke()
will use it as an argument. As result we invoke wrong callback.
That behaviour was in place since:
commit fcaaba6c7136 ("dmaengine: imx-dma: fix callback path in tasklet").
But after commit 4cd13c21b207 ("softirq: Let ksoftirqd do its job")
things got worse, since possible delay between tasklet_schedule()
from DMA irq handler and actual tasklet function execution got bigger.
And that gave more time for new DMA request to be submitted and
to be put into "ld_queue" list.
It has been noticed that DMA issue is causing problems for "mxc-mmc"
driver. While stressing the system with heavy network traffic and
writing/reading to/from sd card simultaneously the timeout may happen:
10013000.sdhci: mxcmci_watchdog: read time out (status = 0x30004900)
There are multiple issues with bcm2835_dma_abort() (which is called on
termination of a transaction):
* The algorithm to abort the transaction first pauses the channel by
clearing the ACTIVE flag in the CS register, then waits for the PAUSED
flag to clear. Page 49 of the spec documents the latter as follows:
"Indicates if the DMA is currently paused and not transferring data.
This will occur if the active bit has been cleared [...]"
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
So the function is entering an infinite loop because it is waiting for
PAUSED to clear which is always set due to the function having cleared
the ACTIVE flag. The only thing that's saving it from itself is the
upper bound of 10000 loop iterations.
The code comment says that the intention is to "wait for any current
AXI transfer to complete", so the author probably wanted to check the
WAITING_FOR_OUTSTANDING_WRITES flag instead. Amend the function
accordingly.
* The CS register is only read at the beginning of the function. It
needs to be read again after pausing the channel and before checking
for outstanding writes, otherwise writes which were issued between
the register read at the beginning of the function and pausing the
channel may not be waited for.
* The function seeks to abort the transfer by writing 0 to the NEXTCONBK
register and setting the ABORT and ACTIVE flags. Thereby, the 0 in
NEXTCONBK is sought to be loaded into the CONBLK_AD register. However
experimentation has shown this approach to not work: The CONBLK_AD
register remains the same as before and the CS register contains
0x00000030 (PAUSED | DREQ_STOPS_DMA). In other words, the control
block is not aborted but merely paused and it will be resumed once the
next DMA transaction is started. That is absolutely not the desired
behavior.
A simpler approach is to set the channel's RESET flag instead. This
reliably zeroes the NEXTCONBK as well as the CS register. It requires
less code and only a single MMIO write. This is also what popular
user space DMA drivers do, e.g.:
https://github.com/metachris/RPIO/blob/master/source/c_pwm/pwm.c
Note that the spec is contradictory whether the NEXTCONBK register
is writeable at all. On the one hand, page 41 claims:
"The value loaded into the NEXTCONBK register can be overwritten so
that the linked list of Control Block data structures can be
dynamically altered. However it is only safe to do this when the DMA
is paused."
On the other hand, page 40 specifies:
"Only three registers in each channel's register set are directly
writeable (CS, CONBLK_AD and DEBUG). The other registers (TI,
SOURCE_AD, DEST_AD, TXFR_LEN, STRIDE & NEXTCONBK), are automatically
loaded from a Control Block data structure held in external memory."
If IRQ handlers are threaded (either because CONFIG_PREEMPT_RT_BASE is
enabled or "threadirqs" was passed on the command line) and if system
load is sufficiently high that wakeup latency of IRQ threads degrades,
SPI DMA transactions on the BCM2835 occasionally break like this:
ks8851 spi0.0: SPI transfer timed out
bcm2835-dma 3f007000.dma: DMA transfer could not be terminated
ks8851 spi0.0 eth2: ks8851_rdfifo: spi_sync() failed
The root cause is an assumption made by the DMA driver which is
documented in a code comment in bcm2835_dma_terminate_all():
/*
* Stop DMA activity: we assume the callback will not be called
* after bcm_dma_abort() returns (even if it does, it will see
* c->desc is NULL and exit.)
*/
That assumption falls apart if the IRQ handler bcm2835_dma_callback() is
threaded: A client may terminate a descriptor and issue a new one
before the IRQ handler had a chance to run. In fact the IRQ handler may
miss an *arbitrary* number of descriptors. The result is the following
race condition:
1. A descriptor finishes, its interrupt is deferred to the IRQ thread.
2. A client calls dma_terminate_async() which sets channel->desc = NULL.
3. The client issues a new descriptor. Because channel->desc is NULL,
bcm2835_dma_issue_pending() immediately starts the descriptor.
4. Finally the IRQ thread runs and writes BCM2835_DMA_INT to the CS
register to acknowledge the interrupt. This clears the ACTIVE flag,
so the newly issued descriptor is paused in the middle of the
transaction. Because channel->desc is not NULL, the IRQ thread
finalizes the descriptor and tries to start the next one.
I see two possible solutions: The first is to call synchronize_irq()
in bcm2835_dma_issue_pending() to wait until the IRQ thread has
finished before issuing a new descriptor. The downside of this approach
is unnecessary latency if clients desire rapidly terminating and
re-issuing descriptors and don't have any use for an IRQ callback.
(The SPI TX DMA channel is a case in point.)
A better alternative is to make the IRQ thread recognize that it has
missed descriptors and avoid finalizing the newly issued descriptor.
So first of all, set the ACTIVE flag when acknowledging the interrupt.
This keeps a newly issued descriptor running.
If the descriptor was finished, the channel remains idle despite the
ACTIVE flag being set. However the ACTIVE flag can then no longer be
used to check whether the channel is idle, so instead check whether
the register containing the current control block address is zero
and finalize the current descriptor only if so.
That way, there is no impact on latency and throughput if the client
doesn't care for the interrupt: Only minimal additional overhead is
introduced for non-cyclic descriptors as one further MMIO read is
necessary per interrupt to check for idleness of the channel. Cyclic
descriptors are sped up slightly by removing one MMIO write per
interrupt.
Ring buffer implementation in hid_debug_event() and hid_debug_events_read()
is strange allowing lost or corrupted data. After commit 717adfdaf147
("HID: debug: check length before copy_to_user()") it is possible to enter
an infinite loop in hid_debug_events_read() by providing 0 as count, this
locks up a system. Fix this by rewriting the ring buffer implementation
with kfifo and simplify the code.
This fixes CVE-2019-3819.
v2: fix an execution logic and add a comment
v3: use __set_current_state() instead of set_current_state()
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1669187 Cc: stable@vger.kernel.org # v4.18+ Fixes: cd667ce24796 ("HID: use debugfs for events/reports dumping") Fixes: 717adfdaf147 ("HID: debug: check length before copy_to_user()") Signed-off-by: Vladis Dronov <vdronov@redhat.com> Reviewed-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the pipe_buf_release() handlers seem to assume that the pipe is
locked - in particular, anon_pipe_buf_release() accesses pipe->tmp_page
without taking any extra locks. From a glance through the callers of
pipe_buf_release(), it looks like FUSE is the only one that calls
pipe_buf_release() without having the pipe locked.
This bug should only lead to a memory leak, nothing terrible.
On the System76 Darter Pro (darp5), there is a headset microphone
input attached to 0x1a that does not have a jack detect. In order to
get it working, the pin configuration needs to be set correctly, and
the ALC269_FIXUP_HEADSET_MODE_NO_HP_MIC fixup needs to be applied.
This is similar to the MIC_NO_PRESENCE fixups for some Dell laptops,
except we have a separate microphone jack that is already configured
correctly.
In the current code, the codec registration may happen both at the
codec bind time and the end of the controller probe time. In a rare
occasion, they race with each other, leading to Oops due to the still
uninitialized card device.
This patch introduces a simple flag to prevent the codec registration
at the codec bind time as long as the controller probe is going on.
The controller probe invokes snd_card_register() that does the whole
registration task, and we don't need to register each piece
beforehand.
This patch adds the T+A VID to the generic check in order to enable
native DSD support for T+A devices. This works with the new T+A USB
DAC model SD3100HV and will also work with future devices which
support the XMOS/Thesycon style DSD format.
It is normal user behaviour to start, stop, then start a stream
again without closing it. Currently this works for compressed
playback streams but not capture ones.
The states on a compressed capture stream go directly from OPEN to
PREPARED, unlike a playback stream which moves to SETUP and waits
for a write of data before moving to PREPARED. Currently however,
when a stop is sent the state is set to SETUP for both types of
streams. This leaves a capture stream in the situation where a new
start can't be sent as that requires the state to be PREPARED and
a new set_params can't be sent as that requires the state to be
OPEN. The only option being to close the stream, and then reopen.
Correct this issues by allowing snd_compr_drain_notify to set the
state depending on the stream direction, as we already do in
set_params.
Fixes: 49bb6402f1aa ("ALSA: compress_core: Add support for capture streams") Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cached writeback mapping is EOF trimmed to try and avoid races
between post-eof block management and writeback that result in
sending cached data to a stale location. The cached mapping is
currently trimmed on the validation check, which leaves a race
window between the time the mapping is cached and when it is trimmed
against the current inode size.
For example, if a new mapping is cached by delalloc conversion on a
blocksize == page size fs, we could cycle various locks, perform
memory allocations, etc. in the writeback codepath before the
associated mapping is eventually trimmed to i_size. This leaves
enough time for a post-eof truncate and file append before the
cached mapping is trimmed. The former event essentially invalidates
a range of the cached mapping and the latter bumps the inode size
such the trim on the next writepage event won't trim all of the
invalid blocks. fstest generic/464 reproduces this scenario
occasionally and causes a lost writeback and stale delalloc blocks
warning on inode inactivation.
To work around this problem, trim the cached writeback mapping as
soon as it is cached in addition to on subsequent validation checks.
This is a minor tweak to tighten the race window as much as possible
until a proper invalidation mechanism is available.
Fixes: 40214d128e07 ("xfs: trim writepage mapping to within eof") Cc: <stable@vger.kernel.org> # v4.14+ Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Allison Henderson <allison.henderson@oracle.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, we have a switch which pads non-zero octets, this
causes kernel hardware checksum fault repeatedly.
Prior to:
commit '88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE ...")'
skb checksum was forced to be CHECKSUM_NONE when padding is detected.
After it, we need to keep skb->csum updated, like what we do for RXFCS.
However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP
headers, it is not worthy the effort as the packets are so small that
CHECKSUM_COMPLETE can't save anything.
Fixes: 88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"), Cc: Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Cc: Nikola Ciprich <nikola.ciprich@linuxbox.cz> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the issues with non BCM58XX chips in the b53 driver
failing, when the irq is not specified in the device tree.
Removed the check for BCM58XX in b53_srab_prepare_irq(),
so the 'port->irq' will be set to '-EXIO' if the irq is not
specified in the device tree.
Fixes: 16994374a6fc ("net: dsa: b53: Make SRAB driver manage port interrupts") Fixes: b2ddc48a81b5 ("net: dsa: b53: Do not fail when IRQ are not initialized") Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In fl_change(), when adding a new rule (i.e. fold == NULL), a driver may
reject the new rule, for example due to resource exhaustion. By that
point, the new rule was already assigned a mask, and it was added to
that mask's hash table. The clean-up path that's invoked as a result of
the rejection however neglects to undo the hash table addition, and
proceeds to free the new rule, thus leaving a dangling pointer in the
hash table.
Fix by removing fnew from the mask's hash table before it is freed.
Fixes: 35cc3cefc4de ("net/sched: cls_flower: Reject duplicated rules also under skip_sw") Signed-off-by: Petr Machata <petrm@mellanox.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling firmware to allocate a CP ring or NQ, an interrupt associated
with that ring may be generated immediately before the doorbell is even
setup after the firmware call returns. When servicing the interrupt, the
driver may crash when trying to access the doorbell.
Fix it by disabling interrupt on that vector until the doorbell is
set up.
Fixes: 697197e5a173 ("bnxt_en: Re-structure doorbells.") Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously virtnet_xdp_xmit() did not account for device tx counters,
which caused confusions.
To be consistent with SKBs, account them on freeing xdp_frames.
Reported-by: David Ahern <dsahern@gmail.com> Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log