Local random address needs to be updated before creating connection if
RPA from LE Direct Advertising Report was resolved in host. Otherwise
remote device might ignore connection request due to address mismatch.
This was affecting following qualification test cases:
GAP/CONN/SCEP/BV-03-C, GAP/CONN/GCEP/BV-05-C, GAP/CONN/DCEP/BV-05-C
Before patch:
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #11350 [hci0] 84680.231216
Address: 56:BC:E8:24:11:68 (Resolvable)
Identity type: Random (0x01)
Identity: F2:F1:06:3D:9C:42 (Static)
> HCI Event: Command Complete (0x0e) plen 4 #11351 [hci0] 84680.246022
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #11352 [hci0] 84680.246417
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 30.000 msec (0x0030)
Own address type: Random (0x01)
Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4 #11353 [hci0] 84680.248854
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #11354 [hci0] 84680.249466
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #11355 [hci0] 84680.253222
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18 #11356 [hci0] 84680.458387
LE Direct Advertising Report (0x0b)
Num reports: 1
Event type: Connectable directed - ADV_DIRECT_IND (0x01)
Address type: Random (0x01)
Address: 53:38:DA:46:8C:45 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Direct address type: Random (0x01)
Direct address: 7C:D6:76:8C:DF:82 (Resolvable)
Identity type: Random (0x01)
Identity: F2:F1:06:3D:9C:42 (Static)
RSSI: -74 dBm (0xb6)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #11357 [hci0] 84680.458737
Scanning: Disabled (0x00)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #11358 [hci0] 84680.469982
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25 #11359 [hci0] 84680.470444
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Filter policy: White list is not used (0x00)
Peer address type: Random (0x01)
Peer address: 53:38:DA:46:8C:45 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Own address type: Random (0x01)
Min connection interval: 30.00 msec (0x0018)
Max connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4 #11360 [hci0] 84680.474971
LE Create Connection (0x08|0x000d) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0 #11361 [hci0] 84682.545385
> HCI Event: Command Complete (0x0e) plen 4 #11362 [hci0] 84682.551014
LE Create Connection Cancel (0x08|0x000e) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19 #11363 [hci0] 84682.551074
LE Connection Complete (0x01)
Status: Unknown Connection Identifier (0x02)
Handle: 0
Role: Master (0x00)
Peer address type: Public (0x00)
Peer address: 00:00:00:00:00:00 (OUI 00-00-00)
Connection interval: 0.00 msec (0x0000)
Connection latency: 0 (0x0000)
Supervision timeout: 0 msec (0x0000)
Master clock accuracy: 0x00
After patch:
< HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #210 [hci0] 667.152459
Type: Passive (0x00)
Interval: 60.000 msec (0x0060)
Window: 30.000 msec (0x0030)
Own address type: Random (0x01)
Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02)
> HCI Event: Command Complete (0x0e) plen 4 #211 [hci0] 667.153613
LE Set Scan Parameters (0x08|0x000b) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #212 [hci0] 667.153704
Scanning: Enabled (0x01)
Filter duplicates: Enabled (0x01)
> HCI Event: Command Complete (0x0e) plen 4 #213 [hci0] 667.154584
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 18 #214 [hci0] 667.182619
LE Direct Advertising Report (0x0b)
Num reports: 1
Event type: Connectable directed - ADV_DIRECT_IND (0x01)
Address type: Random (0x01)
Address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Direct address type: Random (0x01)
Direct address: 7C:C1:57:A5:B7:A8 (Resolvable)
Identity type: Random (0x01)
Identity: F4:28:73:5D:38:B0 (Static)
RSSI: -70 dBm (0xba)
< HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #215 [hci0] 667.182704
Scanning: Disabled (0x00)
Filter duplicates: Disabled (0x00)
> HCI Event: Command Complete (0x0e) plen 4 #216 [hci0] 667.183599
LE Set Scan Enable (0x08|0x000c) ncmd 1
Status: Success (0x00)
< HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #217 [hci0] 667.183645
Address: 7C:C1:57:A5:B7:A8 (Resolvable)
Identity type: Random (0x01)
Identity: F4:28:73:5D:38:B0 (Static)
> HCI Event: Command Complete (0x0e) plen 4 #218 [hci0] 667.184590
LE Set Random Address (0x08|0x0005) ncmd 1
Status: Success (0x00)
< HCI Command: LE Create Connection (0x08|0x000d) plen 25 #219 [hci0] 667.184613
Scan interval: 60.000 msec (0x0060)
Scan window: 60.000 msec (0x0060)
Filter policy: White list is not used (0x00)
Peer address type: Random (0x01)
Peer address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Own address type: Random (0x01)
Min connection interval: 30.00 msec (0x0018)
Max connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Min connection length: 0.000 msec (0x0000)
Max connection length: 0.000 msec (0x0000)
> HCI Event: Command Status (0x0f) plen 4 #220 [hci0] 667.186558
LE Create Connection (0x08|0x000d) ncmd 1
Status: Success (0x00)
> HCI Event: LE Meta Event (0x3e) plen 19 #221 [hci0] 667.485824
LE Connection Complete (0x01)
Status: Success (0x00)
Handle: 0
Role: Master (0x00)
Peer address type: Random (0x01)
Peer address: 50:52:D9:A6:48:A0 (Resolvable)
Identity type: Public (0x00)
Identity: 11:22:33:44:55:66 (OUI 11-22-33)
Connection interval: 50.00 msec (0x0028)
Connection latency: 0 (0x0000)
Supervision timeout: 420 msec (0x002a)
Master clock accuracy: 0x07
@ MGMT Event: Device Connected (0x000b) plen 13 {0x0002} [hci0] 667.485996
LE Address: 11:22:33:44:55:66 (OUI 11-22-33)
Flags: 0x00000000
Data length: 0
Commit 4a0e3e989d66 ("cdc_ncm: Add support for moving NDP to end
of NCM frame") added logic to reserve space for the NDP at the
end of the NTB/skb. This reservation did not take the final
alignment of the NDP into account, causing us to reserve too
little space. Additionally the padding prior to NDP addition did
not ensure there was enough space for the NDP.
The NTB/skb with the NDP appended would then exceed the configured
max size. This caused the final padding of the NTB to use a
negative count, padding to almost INT_MAX, and resulting in:
Commit e1069bbfcf3b ("net: cdc_ncm: Reduce memory use when kernel
memory low") made this bug much more likely to trigger by reducing
the NTB size under memory pressure.
Link: https://bugs.debian.org/893393 Reported-by: Горбешко Богдан <bodqhrohro@gmail.com> Reported-and-tested-by: Dennis Wassenberg <dennis.wassenberg@secunet.com> Cc: Enrico Mioso <mrkiko.rs@gmail.com> Fixes: 4a0e3e989d66 ("cdc_ncm: Add support for moving NDP to end of NCM frame")
[ bmork: tx_curr_size => tx_max and context fixup for v4.12 and older ] Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Discards issued to a DM thin device can complete to userspace (via
fstrim) _before_ the metadata changes associated with the discards is
reflected in the thinp superblock (e.g. free blocks). As such, if a
user constructs a test that loops repeatedly over these steps, block
allocation can fail due to discards not having completed yet:
1) fill thin device via filesystem file
2) remove file
3) fstrim
From initial report, here:
https://www.redhat.com/archives/dm-devel/2018-April/msg00022.html
"The root cause of this issue is that dm-thin will first remove
mapping and increase corresponding blocks' reference count to prevent
them from being reused before DISCARD bios get processed by the
underlying layers. However. increasing blocks' reference count could
also increase the nr_allocated_this_transaction in struct sm_disk
which makes smd->old_ll.nr_allocated +
smd->nr_allocated_this_transaction bigger than smd->old_ll.nr_blocks.
In this case, alloc_data_block() will never commit metadata to reset
the begin pointer of struct sm_disk, because sm_disk_get_nr_free()
always return an underflow value."
While there is room for improvement to the space-map accounting that
thinp is making use of: the reality is this test is inherently racey and
will result in the previous iteration's fstrim's discard(s) completing
vs concurrent block allocation, via dd, in the next iteration of the
loop.
No amount of space map accounting improvements will be able to allow
user's to use a block before a discard of that block has completed.
So the best we can really do is allow DM thinp to gracefully handle such
aggressive use of all the pool's data by degrading the pool into
out-of-data-space (OODS) mode. We _should_ get that behaviour already
(if space map accounting didn't falsely cause alloc_data_block() to
believe free space was available).. but short of that we handle the
current reality that dm_pool_alloc_data_block() can return -ENOSPC.
Reported-by: Dennis Yang <dennisyang@qnap.com> Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A device may have boundary restrictions where the number of sectors
between boundaries exceeds its max transfer size. In this case, we need
to cap the max size to the smaller of the two limits.
Reported-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com> Tested-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com> Cc: <stable@vger.kernel.org> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When SPI transfers can be offloaded using DMA, the SPI core need to
build a scatterlist to make sure that the buffer to be transferred is
dma-able.
This patch fixes the scatterlist entry size computation in the case
where the maximum acceptable scatterlist entry supported by the DMA
controller is less than PAGE_SIZE, when the buffer is vmalloced.
For each entry, the actual size is given by the minimum between the
desc_len (which is the max buffer size supported by the DMA controller)
and the remaining buffer length until we cross a page boundary.
Fixes: 65598c13fd66 ("spi: Fix per-page mapping of unaligned vmalloc-ed buffer") Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fstests generic/475 provides a way to fail metadata reads while
checking if checksum exists for the inode inside run_delalloc_nocow(),
and csum_exist_in_range() interprets error (-EIO) as inode having
checksum and makes its caller enter the cow path.
In case of free space inode, this ends up with a warning in
cow_file_range().
The same problem applies to btrfs_cross_ref_exist() since it may also
read metadata in between.
With this, run_delalloc_nocow() bails out when errors occur at the two
places.
cc: <stable@vger.kernel.org> v2.6.28+ Fixes: 17d217fe970d ("Btrfs: fix nodatasum handling in balancing code") Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40f7090bb1b4 ("Input: elan_i2c_smbus - fix corrupted stack")
fixed most of the functions using i2c_smbus_read_block_data() to
allocate a buffer with the maximum block size. However three
functions were left unchanged:
* In elan_smbus_initialize(), increase the buffer size in the same
way.
* In elan_smbus_calibrate_result(), the buffer is provided by the
caller (calibrate_store()), so introduce a bounce buffer. Also
name the result buffer size.
* In elan_smbus_get_report(), the buffer is provided by the caller
but happens to be the right length. Add a compile-time assertion
to ensure this remains the case.
Cc: <stable@vger.kernel.org> # 3.19+ Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detect when a directory entry is (possibly partially) beyond directory
size and return EIO in that case since it means the filesystem is
corrupted. Otherwise directory operations can further corrupt the
directory and possibly also oops the kernel.
CC: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> CC: stable@vger.kernel.org Reported-and-tested-by: Anatoly Trosinenko <anatoly.trosinenko@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 910f8befdf5b ("xen/pirq: fix error path cleanup when binding
MSIs") fixed a couple of errors in error cleanup path of
xen_bind_pirq_msi_to_irq(). This cleanup allowed a call to
__unbind_from_irq() with an unbound irq, which would result in
triggering the BUG_ON there.
Since there is really no reason for the BUG_ON (xen_free_irq() can
operate on unbound irqs) we can remove it.
In nfs_idmap_read_and_verify_message there is an incorrect sprintf '%d'
that converts the __u32 'im_id' from struct idmap_msg to 'id_str', which
is a stack char array variable of length NFS_UINT_MAXLEN == 11.
If a uid or gid value is > 2147483647 = 0x7fffffff, the conversion
overflows into a negative value, for example:
crash> p (unsigned) (0x80000000)
$1 = 2147483648
crash> p (signed) (0x80000000)
$2 = -2147483648
The '-' sign is written to the buffer and this causes a 1 byte overflow
when the NULL byte is written, which corrupts kernel stack memory. If
CONFIG_CC_STACKPROTECTOR_STRONG is set we see a stack-protector panic:
Fix this by calling the internally defined nfs_map_numeric_to_string()
function which properly uses '%u' to convert this __u32. For consistency,
also replace the one other place where snprintf is called.
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com> Reported-by: Stephen Johnston <sjohnsto@redhat.com> Fixes: cf4ab538f1516 ("NFSv4: Fix the string length returned by the idmapper") Cc: stable@vger.kernel.org # v3.4+ Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nfsd4_readdir_rsize restricts rd_maxcount to svc_max_payload when
estimating the size of the readdir reply, but nfsd_encode_readdir
restricts it to INT_MAX when encoding the reply. This can result in log
messages like "kernel: RPC request reserved 32896 but used 1049444".
Restrict rd_dircount similarly (no reason it should be larger than
svc_max_payload).
Signed-off-by: Scott Mayhew <smayhew@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As warned by smatch:
drivers/media/dvb-core/dvb_frontend.c:314 dvb_frontend_get_event() warn: inconsistent returns 'sem:&fepriv->sem'.
Locked on: line 288
line 295
line 306
line 314
Unlocked on: line 303
The lock implementation for get event is wrong, as, if an
interrupt occurs, down_interruptible() will fail, and the
routine will call up() twice when userspace calls the ioctl
again.
The bad code is there since when Linux migrated to git, in
2005.
Some Atom CPUs can produce FUP packets that contain NLIP (next linear
instruction pointer) instead of CLIP (current linear instruction
pointer). That will result in "Unexpected indirect branch" errors. Fix
by comparing IP to NLIP in that case.
On some platforms, overflows will clear before MTC wraparound, and there
is no following TSC/TMA packet. In that case the previous TMA is valid.
Since there will be a valid TMA either way, stop setting 'have_tma' to
false upon overflow.
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
This would only cause trouble if the child node is missing while there
is an unrelated node named "backlight" elsewhere in the tree.
Cc: stable <stable@vger.kernel.org> # 3.7 Fixes: eebfdc17cc6c ("backlight: Add TPS65217 WLED driver") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed,
while the child backlight node was leaked.
Cc: stable <stable@vger.kernel.org> # 3.9 Fixes: 47ec340cb8e2 ("mfd: max8925: Support dt for backlight") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix child-node lookup during probe, which ended up searching the whole
device tree depth-first starting at the parent rather than just matching
on its children.
To make things worse, the parent mfd node was also prematurely freed.
Cc: stable <stable@vger.kernel.org> # 3.10 Fixes: 59eb2b5e57ea ("drivers/video/backlight/as3711_bl.c: add OF support") Signed-off-by: Johan Hovold <johan@kernel.org> Acked-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: slab-out-of-bounds in xfrm_hash_rebuild+0xdbe/0xf00 net/xfrm/xfrm_policy.c:618
read of size 2 at addr ffff8801c8e92fe4 by task kworker/1:1/23 [..]
Workqueue: events xfrm_hash_rebuild [..]
__asan_report_load2_noabort+0x14/0x20 mm/kasan/report.c:428
xfrm_hash_rebuild+0xdbe/0xf00 net/xfrm/xfrm_policy.c:618
process_one_work+0xbbf/0x1b10 kernel/workqueue.c:2112
worker_thread+0x223/0x1990 kernel/workqueue.c:2246 [..]
The reproducer triggers:
1016 if (error) {
1017 list_move_tail(&walk->walk.all, &x->all);
1018 goto out;
1019 }
in xfrm_policy_walk() via pfkey (it sets tiny rcv space, dump
callback returns -ENOBUFS).
In this case, *walk is located the pfkey socket struct, so this socket
becomes visible in the global policy list.
It looks like this is intentional -- phony walker has walk.dead set to 1
and all other places skip such "policies".
Ccing original authors of the two commits that seem to expose this
issue (first patch missed ->dead check, second patch adds pfkey
sockets to policies dumper list).
Fixes: 880a6fab8f6ba5b ("xfrm: configure policy hash table thresholds by netlink") Fixes: 12a169e7d8f4b1c ("ipsec: Put dumpers on the dump list") Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Timo Teras <timo.teras@iki.fi> Cc: Christophe Gouault <christophe.gouault@6wind.com> Reported-by: syzbot <bot+c028095236fcb6f4348811565b75084c754dc729@syzkaller.appspotmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Cc: Zubin Mithra <zsm@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever thresholds are changed the hash tables are rebuilt. This is
done by enumerating all policies and hashing and inserting them into
the right table according to the thresholds and direction.
Because socket policies are also contained in net->xfrm.policy_all but
no hash tables are defined for their direction (dir + XFRM_POLICY_MAX)
this causes a NULL or invalid pointer dereference after returning from
policy_hash_bysel() if the rebuild is done while any socket policies
are installed.
Since the rebuild after changing thresholds is scheduled this crash
could even occur if the userland sets thresholds seemingly before
installing any socket policies.
Fixes: 53c2e285f970 ("xfrm: Do not hash socket policies") Signed-off-by: Tobias Brunner <tobias@strongswan.org> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Cc: Zubin Mithra <zsm@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is potential for the size and len fields in ubifs_data_node to be
too large causing either a negative value for the length fields or an
integer overflow leading to an incorrect memory allocation. Likewise,
when the len field is small, an integer underflow may occur.
Ben Hutchings pointed out that 29b7a6fa1ec0 ("ubi: fastmap: Don't flush
fastmap work on detach") does not really fix the problem, it just
reduces the risk to hit the race window where fastmap work races against
free()'ing ubi->volumes[].
The correct approach is making sure that no more fastmap work is in
progress before we free ubi data structures.
So we cancel fastmap work right after the ubi background thread is
stopped.
By setting ubi->thread_enabled to zero we make sure that no further work
tries to wake the thread.
Fixes: 29b7a6fa1ec0 ("ubi: fastmap: Don't flush fastmap work on detach") Fixes: 74cdaf24004a ("UBI: Fastmap: Fix memory leaks while closing the WL sub-system") Cc: stable@vger.kernel.org Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Cc: Martin Townsend <mtownsend1973@gmail.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If "re-add" is written to the "state" file for a device
which is faulty, this has an effect similar to removing
and re-adding the device. It should take up the
same slot in the array that it previously had, and
an accelerated (e.g. bitmap-based) rebuild should happen.
The slot that "it previously had" is determined by
rdev->saved_raid_disk.
However this is not set when a device fails (only when a device
is added), and it is cleared when resync completes.
This means that "re-add" will normally work once, but may not work a
second time.
This patch includes two fixes.
1/ when a device fails, record the ->raid_disk value in
->saved_raid_disk before clearing ->raid_disk
2/ when "re-add" is written to a device for which
->saved_raid_disk is not set, fail.
I think this is suitable for stable as it can
cause re-adding a device to be forced to do a full
resync which takes a lot longer and so puts data at
more risk.
The pmem driver does not honor a forced read-only setting for very long:
$ blockdev --setro /dev/pmem0
$ blockdev --getro /dev/pmem0
1
followed by various commands like these:
$ blockdev --rereadpt /dev/pmem0
or
$ mkfs.ext4 /dev/pmem0
results in this in the kernel serial log:
nd_pmem namespace0.0: region0 read-write, marking pmem0 read-write
with the read-only setting lost:
$ blockdev --getro /dev/pmem0
0
That's from bus.c nvdimm_revalidate_disk(), which always applies the
setting from nd_region (which is initially based on the ACPI NFIT
NVDIMM state flags not_armed bit).
In contrast, commit 20bd1d026aac ("scsi: sd: Keep disk read-only when
re-reading partition") fixed this issue for SCSI devices to preserve
the previous setting if it was set to read-only.
This patch modifies bus.c to preserve any previous read-only setting.
It also eliminates the kernel serial log print except for cases where
read-write is changed to read-only, so it doesn't print read-only to
read-only non-changes.
Cc: <stable@vger.kernel.org> Fixes: 581388209405 ("libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only") Signed-off-by: Robert Elliott <elliott@hpe.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That other commit introduced an inconsistency because it would trace on
ERP_FAILED for all callers of port forced reopen triggers (not just
terminate_rport_io), but it would not trace on ERP_FAILED for all callers of
other ERP triggers such as adapter, port regular, LUN.
Therefore, generalize that other commit. zfcp_erp_action_enqueue() already
had two early outs which re-used the one zfcp_dbf_rec_trig() call. All ERP
trigger functions finally run through zfcp_erp_action_enqueue(). So move
the special handling for ZFCP_STATUS_COMMON_ERP_FAILED into
zfcp_erp_action_enqueue() and add another early out with new trace marker
for pseudo ERP need in this case. This removes all early returns from all
ERP trigger functions so we always end up at zfcp_dbf_rec_trig().
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1 ZFCP_DBF_REC_TRIG
Tag : .......
LUN : 0x...
WWPN : 0x...
D_ID : 0x...
Adapter status : 0x...
Port status : 0x...
LUN status : 0x...
Ready count : 0x...
Running count : 0x...
ERP want : 0x0. ZFCP_ERP_ACTION_REOPEN_...
ERP need : 0xe0 ZFCP_ERP_ACTION_FAILED
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_device() and its internally used kobject_get() only return NULL if they
get passed NULL as argument. zfcp_get_port_by_wwpn() loops over
adapter->port_list so the iteration variable port is always non-NULL.
Struct device is embedded in struct zfcp_port so &port->dev is always
non-NULL. This is the argument to get_device(). However, if we get an
fc_rport in terminate_rport_io() for which we cannot find a match within
zfcp_get_port_by_wwpn(), the latter can return NULL. v2.6.30 commit 70932935b61e ("[SCSI] zfcp: Fix oops when port disappears") introduced an
early return without adding a trace record for this case. Even if we don't
need recovery in this case, for debugging we should still see that our
callback was invoked originally by scsi_transport_fc.
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : REC
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : sctrpin SCSI terminate rport I/O, no zfcp port
LUN : 0xffffffffffffffff none (invalid)
WWPN : 0x<wwpn> WWPN
D_ID : 0x<n_port_id> N_Port-ID
Adapter status : 0x...
Port status : 0xffffffff unknown (-1)
LUN status : 0x00000000 none (invalid)
Ready count : 0x...
Running count : 0x...
ERP want : 0x03 ZFCP_ERP_ACTION_REOPEN_PORT_FORCED
ERP need : 0xc0 ZFCP_ERP_ACTION_NONE
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 70932935b61e ("[SCSI] zfcp: Fix oops when port disappears") Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a SCSI device is deleted during scsi_eh host reset, we cannot get a
reference to the SCSI device anymore since scsi_device_get returns !=0 by
design. Assuming the recovery of adapter and port(s) was successful,
zfcp_erp_strategy_followup_success() attempts to trigger a LUN reset for the
half-gone SCSI device. Unfortunately, it causes the following confusing
trace record which states that zfcp will do a LUN recovery as "ERP need" is
ZFCP_ERP_ACTION_REOPEN_LUN == 1 and equals "ERP want".
Old example trace record formatted with zfcpdbf from s390-tools:
Tag: : ersfs_3 ERP, trigger, unit reopen, port reopen succeeded
LUN : 0x<FCP_LUN>
WWPN : 0x<WWPN>
D_ID : 0x<N_Port-ID>
Adapter status : 0x5400050b
Port status : 0x54000001
LUN status : 0x40000000 ZFCP_STATUS_COMMON_RUNNING
but not ZFCP_STATUS_COMMON_UNBLOCKED as it
was closed on close part of adapter reopen
ERP want : 0x01
ERP need : 0x01 misleading
However, zfcp_erp_setup_act() returns NULL as it cannot get the reference.
Hence, zfcp_erp_action_enqueue() takes an early goto out and _NO_ recovery
actually happens.
We always do want the recovery trigger trace record even if no erp_action
could be enqueued as in this case. For other cases where we did not enqueue
an erp_action, 'need' has always been zero to indicate this. In order to
indicate above goto out, introduce an eyecatcher "flag" to mark the "ERP
need" as 'not needed' but still keep the information which erp_action type,
that zfcp_erp_required_act() had decided upon, is needed. 0xc_ is chosen to
be visibly different from 0x0_ in "ERP want".
New example trace record formatted with zfcpdbf from s390-tools:
Tag: : ersfs_3 ERP, trigger, unit reopen, port reopen succeeded
LUN : 0x<FCP_LUN>
WWPN : 0x<WWPN>
D_ID : 0x<N_Port-ID>
Adapter status : 0x5400050b
Port status : 0x54000001
LUN status : 0x40000000
ERP want : 0x01
ERP need : 0xc1 would need LUN ERP, but no action set up
^
Before v2.6.38 commit ae0904f60fab ("[SCSI] zfcp: Redesign of the debug
tracing for recovery actions.") we could detect this case because the
"erp_action" field in the trace was NULL. The rework removed erp_action as
argument and field from the trace.
This patch here is for tracing. A fix to allow LUN recovery in the case at
hand is a topic for a separate patch.
See also commit fdbd1c5e27da ("[SCSI] zfcp: Allow running unit/LUN shutdown
without acquiring reference") for a similar case and background info.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: ae0904f60fab ("[SCSI] zfcp: Redesign of the debug tracing for recovery actions.") Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have a SCSI trace for the end of abort and scsi_eh TMF. Due to
zfcp_erp_wait() and fc_block_scsi_eh() time can pass between the start of
our eh callback and an actual send/recv of an abort / TMF request. In order
to see the temporal sequence including any abort / TMF send retries, add a
trace before the above two blocking functions. This supports problem
determination with scsi_eh and parallel zfcp ERP.
No need to explicitly trace the beginning of our eh callback, since we
typically can send an abort / TMF and see its HBA response (in the worst
case, it's a pseudo response on dismiss all of adapter recovery, e.g. due to
an FSF request timeout [fsrth_1] of the abort / TMF). If we cannot send, we
now get a trace record for the first "abrt_wt" or "[lt]r_wait" which denotes
almost the beginning of the callback.
No need to explicitly trace the wakeup after the above two blocking
functions because the next retry loop causes another trace in any case and
that is sufficient.
Example trace records formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : abrt_wt abort, before zfcp_erp_wait()
Request ID : 0x0000000000000000 none (invalid)
SCSI ID : 0x<scsi_id>
SCSI LUN : 0x<scsi_lun>
SCSI LUN high : 0x<scsi_lun_high>
SCSI result : 0x<scsi_result_of_cmd_to_be_aborted>
SCSI retries : 0x<retries_of_cmd_to_be_aborted>
SCSI allowed : 0x<allowed_retries_of_cmd_to_be_aborted>
SCSI scribble : 0x<req_id_of_cmd_to_be_aborted>
SCSI opcode : <CDB_of_cmd_to_be_aborted>
FCP rsp inf cod: 0x.. none (invalid)
FCP rsp IU : ... none (invalid)
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : lr_wait LUN reset, before zfcp_erp_wait()
Request ID : 0x0000000000000000 none (invalid)
SCSI ID : 0x<scsi_id>
SCSI LUN : 0x<scsi_lun>
SCSI LUN high : 0x<scsi_lun_high>
SCSI result : 0x... unrelated
SCSI retries : 0x.. unrelated
SCSI allowed : 0x.. unrelated
SCSI scribble : 0x... unrelated
SCSI opcode : ... unrelated
FCP rsp inf cod: 0x.. none (invalid)
FCP rsp IU : ... none (invalid)
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: 63caf367e1c9 ("[SCSI] zfcp: Improve reliability of SCSI eh handlers in zfcp") Fixes: af4de36d911a ("[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED") Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For problem determination we need to see whether and why we were successful
or not. This allows deduction of scsi_eh escalation.
Example trace record formatted with zfcpdbf from s390-tools:
Timestamp : ...
Area : SCSI
Subarea : 00
Level : 1
Exception : -
CPU ID : ..
Caller : 0x...
Record ID : 1
Tag : schrh_r SCSI host reset handler result
Request ID : 0x0000000000000000 none (invalid)
SCSI ID : 0xffffffff none (invalid)
SCSI LUN : 0xffffffff none (invalid)
SCSI LUN high : 0xffffffff none (invalid)
SCSI result : 0x00002002 field re-used for midlayer value: SUCCESS
or in other cases: 0x2009 == FAST_IO_FAIL
SCSI retries : 0xff none (invalid)
SCSI allowed : 0xff none (invalid)
SCSI scribble : 0xffffffffffffffff none (invalid)
SCSI opcode : ffffffffffffffffffffffffffffffff none (invalid)
FCP rsp inf cod: 0xff none (invalid)
FCP rsp IU : 00000000000000000000000000000000 none (invalid) 0000000000000000
v2.6.35 commit a1dbfddd02d2 ("[SCSI] zfcp: Pass return code from
fc_block_scsi_eh to scsi eh") introduced the first return with something
other than the previously hardcoded single SUCCESS return path.
Signed-off-by: Steffen Maier <maier@linux.ibm.com> Fixes: a1dbfddd02d2 ("[SCSI] zfcp: Pass return code from fc_block_scsi_eh to scsi eh") Cc: <stable@vger.kernel.org> #2.6.38+ Reviewed-by: Jens Remus <jremus@linux.ibm.com> Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prevents driver from setting lower default speed of 1 GB/sec,
if the switch does not support Get Port Speed Capabilities (GPSC)
command. Setting this default speed results into much lower write
performance for large sequential WRITE. This patch modifies driver to
check for gpsc_supported flags and prevents driver from issuing
MBC_SET_PORT_PARAM (001Ah) to set default speed of 1 GB/sec. If driver
does not send this mailbox command, firmware assumes maximum supported
link speed and will operate at the max speed.
Cc: stable@vger.kernel.org Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Reported-by: Eda Zhou <ezhou@redhat.com> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Tested-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we use int for buffer length and bytes_per_datum. However,
kfifo uses unsigned int for length and size_t for element size. We need
to make sure these matches or we will have bugs related to overflow (in
the range between INT_MAX and UINT_MAX for length, for example).
In addition, set_bytes_per_datum uses size_t while bytes_per_datum is an
int, which would cause bugs for large values of bytes_per_datum.
Change buffer length to use unsigned int and bytes_per_datum to use
size_t.
Signed-off-by: Martin Kelly <mkelly@xevo.com> Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[bwh: Backported to 4.4:
- Drop change to iio_dma_buffer_set_length()
- Adjust filename, context] Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In btrfs_clone_files(), we must check the NODATASUM flag while the
inodes are locked. Otherwise, it's possible that btrfs_ioctl_setflags()
will change the flags after we check and we can end up with a party
checksummed file.
The race window is only a few instructions in size, between the if and
the locks which is:
3834 if (S_ISDIR(src->i_mode) || S_ISDIR(inode->i_mode))
3835 return -EISDIR;
where the setflags must be run and toggle the NODATASUM flag (provided
the file size is 0). The clone will block on the inode lock, segflags
takes the inode lock, changes flags, releases log and clone continues.
Not impossible but still needs a lot of bad luck to hit unintentionally.
Fixes: 0e7b824c4ef9 ("Btrfs: don't make a file partly checksummed through file clone") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Omar Sandoval <osandov@fb.com> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ adjusted for 4.4 ] Signed-off-by: Nikolay Borisov <nborisov@suse.com>
For the common cases where 1000 is a multiple of HZ, or HZ is a multiple of
1000, jiffies_to_msecs() never returns zero when passed a non-zero time
period.
However, if HZ > 1000 and not an integer multiple of 1000 (e.g. 1024 or
1200, as used on alpha and DECstation), jiffies_to_msecs() may return zero
for small non-zero time periods. This may break code that relies on
receiving back a non-zero value.
jiffies_to_usecs() does not need such a fix: one jiffy can only be less
than one µs if HZ > 1000000, and such large values of HZ are already
rejected at build time, twice:
- include/linux/jiffies.h does #error if HZ >= 12288,
- kernel/time/time.c has BUILD_BUG_ON(HZ > USEC_PER_SEC).
While a barrier is present in the outX() functions before the register
write, a similar barrier is missing in the inX() functions after the
register read. This could allow memory accesses following inX() to
observe stale data.
This patch is very similar to commit a1cc7034e33d12dc1 ("MIPS: io: Add
barrier after register read in readX()"). Because war_io_reorder_wmb()
is both used by writeX() and outX(), if readX() need a barrier then so
does inX().
After a suspend/resume cycle the Presence Detect or Data Link Layer Status
Changed bits might be set. If we don't clear them those events will not
fire anymore and nothing happens for instance when a device is now
hot-unplugged.
Fix this by clearing those bits in a newly introduced function
pcie_reenable_notification(). This should be fine because immediately
after, we check if the adapter is still present by reading directly from
the status register.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The erratum and workaround are described by BCM5300X-ES300-RDS.pdf as
below.
R10: PCIe Transactions Periodically Fail
Description: The BCM5300X PCIe does not maintain transaction ordering.
This may cause PCIe transaction failure.
Fix Comment: Add a dummy PCIe configuration read after a PCIe
configuration write to ensure PCIe configuration access
ordering. Set ES bit of CP0 configu7 register to enable
sync function so that the sync instruction is functional.
Resolution: hndpci.c: extpci_write_config()
hndmips.c: si_mips_init()
mipsinc.h CONF7_ES
This is fixed by the CFE MIPS bcmsi chipset driver also for BCM47XX.
Also the dummy PCIe configuration read is already implemented in the
Linux BCMA driver.
Enable ExternalSync in Config7 when CONFIG_BCMA_DRIVER_PCI_HOSTMODE=y
too so that the sync instruction is externalised.
The "sector is in requested range" test used to determine whether
sectors should be re-locked or not is done on a variable that is reset
everytime we cross a chip boundary, which can lead to some blocks being
re-locked while the caller expect them to be unlocked.
Fix the check to make sure this cannot happen.
cfi_ppb_unlock() tries to relock all sectors that were locked before
unlocking the whole chip.
This locking used the chip start address + the FULL offset from the
first flash chip, thereby forming an illegal address. Fix that by using
the chip offset(adr).
do_ppb_xxlock() fails to add chip->start when querying for lock status
(and chip_ready test), which caused false status reports.
Fix that by adding adr += chip->start and adjust call sites
accordingly.
For the word write it is checked if the chip has the correct value.
But it is not checked for the write buffer as only checked if ready.
To make sure for the write buffer change to check the value.
It is enough as this patch is only checking the last written word.
Since it is described by data sheets to check the operation status.
Signed-off-by: Tokunori Ikegami <ikegami@allied-telesis.co.jp> Reviewed-by: Joakim Tjernlund <Joakim.Tjernlund@infinera.com> Cc: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Brian Norris <computersforpeace@gmail.com> Cc: David Woodhouse <dwmw2@infradead.org> Cc: Boris Brezillon <boris.brezillon@free-electrons.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Richard Weinberger <richard@nod.at> Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr> Cc: linux-mtd@lists.infradead.org Cc: stable@vger.kernel.org Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For strings, account for trailing \0 in property length field:
This is consistent with how dtc builds string properties.
Function __of_prop_dup() would misbehave on such properties as it duplicates
properties based on the property length field creating new string values
without trailing \0s.
Signed-off-by: Stefan M Schaeckeler <sschaeck@cisco.com> Reviewed-by: Frank Rowand <frank.rowand@sony.com> Tested-by: Frank Rowand <frank.rowand@sony.com> Cc: <stable@vger.kernel.org> Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NUMREGBYTES (which is used as the size for gdb_regs[]) is incorrectly
based on DBG_MAX_REG_NUM instead of GDB_MAX_REGS. DBG_MAX_REG_NUM
is the number of total registers, while GDB_MAX_REGS is the number
of 'unsigned longs' it takes to serialize those registers. Since
FP registers require 3 'unsigned longs' each, DBG_MAX_REG_NUM is
smaller than GDB_MAX_REGS.
This causes GDB 8.0 give the following error on connect:
"Truncated register 19 in remote 'g' packet"
This also causes the register serialization/deserialization logic
to overflow gdb_regs[], overwriting whatever follows.
Fixes: 834b2964b7ab ("kgdb,arm: fix register dump") Cc: <stable@vger.kernel.org> # 2.6.37+ Signed-off-by: David Rivshin <drivshin@allworx.com> Acked-by: Rabin Vincent <rabin@rab.in> Tested-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unregister fadump on kexec down path otherwise the fadump registration
in new kexec-ed kernel complains that fadump is already registered.
This makes new kernel to continue using fadump registered by previous
kernel which may lead to invalid vmcore generation. Hence this patch
fixes this issue by un-registering fadump in fadump_cleanup() which is
called during kexec path so that new kernel can register fadump with
new valid values.
Fixes: b500afff11f6 ("fadump: Invalidate registration and release reserved memory for general use.") Cc: stable@vger.kernel.org # v3.4+ Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 78eaa10f027c ("cpuidle: powernv/pseries: Auto-promotion of
snooze to deeper idle state") introduced a timeout for the snooze idle
state so that it could be eventually be promoted to a deeper idle
state. The snooze timeout value is static and set to the target
residency of the next idle state, which would train the cpuidle
governor to pick the next idle state eventually.
The unfortunate side-effect of this is that if the next idle state(s)
is disabled, the CPU will forever remain in snooze, despite the fact
that the system is completely idle, and other deeper idle states are
available.
This patch fixes the issue by dynamically setting the snooze timeout
to the target residency of the next enabled state on the device.
Before Patch:
POWER8 : Only nap disabled.
$ cpupower monitor sleep 30
sleep took 30.01297 seconds and exited with status 0
|Idle_Stats
PKG |CORE|CPU | snoo | Nap | Fast
0| 8| 0| 96.41| 0.00| 0.00
0| 8| 1| 96.43| 0.00| 0.00
0| 8| 2| 96.47| 0.00| 0.00
0| 8| 3| 96.35| 0.00| 0.00
0| 8| 4| 96.37| 0.00| 0.00
0| 8| 5| 96.37| 0.00| 0.00
0| 8| 6| 96.47| 0.00| 0.00
0| 8| 7| 96.47| 0.00| 0.00
Back when we first introduced the DAWR, in commit 4ae7ebe9522a
("powerpc: Change hardware breakpoint to allow longer ranges"), we
screwed up the constraint making it a 1024 byte boundary rather than a
512. This makes the check overly permissive. Fortunately GDB is the
only real user and it always did they right thing, so we never
noticed.
This fixes the constraint to 512 bytes.
Fixes: 4ae7ebe9522a ("powerpc: Change hardware breakpoint to allow longer ranges") Cc: stable@vger.kernel.org # v3.9+ Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit e2a800beaca1 ("powerpc/hw_brk: Fix off by one error when
validating DAWR region end") we fixed setting the DAWR end point to
its max value via PPC_PTRACE_SETHWDEBUG. Unfortunately we broke
PTRACE_SET_DEBUGREG when setting a 512 byte aligned breakpoint.
PTRACE_SET_DEBUGREG currently sets the length of the breakpoint to
zero (memset() in hw_breakpoint_init()). This worked with
arch_validate_hwbkpt_settings() before the above patch was applied but
is now broken if the breakpoint is 512byte aligned.
This sets the length of the breakpoint to 8 bytes when using
PTRACE_SET_DEBUGREG.
Fixes: e2a800beaca1 ("powerpc/hw_brk: Fix off by one error when validating DAWR region end") Cc: stable@vger.kernel.org # v3.11+ Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we do not have an isync, or any other context synchronizing
instruction prior to the slbie/slbmte in _switch() that updates the
SLB entry for the kernel stack.
However that is not correct as outlined in the ISA.
From Power ISA Version 3.0B, Book III, Chapter 11, page 1133:
"Changing the contents of ... the contents of SLB entries ... can
have the side effect of altering the context in which data
addresses and instruction addresses are interpreted, and in which
instructions are executed and data accesses are performed.
...
These side effects need not occur in program order, and therefore
may require explicit synchronization by software.
...
The synchronizing instruction before the context-altering
instruction ensures that all instructions up to and including that
synchronizing instruction are fetched and executed in the context
that existed before the alteration."
And page 1136:
"For data accesses, the context synchronizing instruction before the
slbie, slbieg, slbia, slbmte, tlbie, or tlbiel instruction ensures
that all preceding instructions that access data storage have
completed to a point at which they have reported all exceptions
they will cause."
We're not aware of any bugs caused by this, but it should be fixed
regardless.
Add the missing isync when updating kernel stack SLB entry.
Cc: stable@vger.kernel.org Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
[mpe: Flesh out change log with more ISA text & explanation] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting NULL pointer dereference at fuse_ctl_remove_conn() [1].
Since fc->ctl_ndents is incremented by fuse_ctl_add_conn() when new_inode()
failed, fuse_ctl_remove_conn() reaches an inode-less dentry and tries to
clear d_inode(dentry)->i_private field.
Fix by only adding the dentry to the array after being fully set up.
When tearing down the control directory, do d_invalidate() on it to get rid
of any mounts that might have been added.
syzbot is reporting use-after-free at fuse_kill_sb_blk() [1].
Since sb->s_fs_info field is not cleared after fc was released by
fuse_conn_put() when initialization failed, fuse_kill_sb_blk() finds
already released fc and tries to hold the lock. Fix this by clearing
sb->s_fs_info field after calling fuse_conn_put().
Fuse has an "atomic_o_trunc" mode, where userspace filesystem uses the
O_TRUNC flag in the OPEN request to truncate the file atomically with the
open.
In this mode there's no need to send a SETATTR request to userspace after
the open, so fuse_do_setattr() checks this mode and returns. But this
misses the important step of truncating the pagecache.
Add the missing parts of truncation to the ATTR_OPEN branch.
AOSP use userspace firmware loader to load firmwares, which will
return -EAGAIN in case qca/rampatch_00440302.bin is not found.
Since there is no rampatch for dragonboard820c QCA controller
revision, just make it work as is.
There was one place where the timeout value for an operation was
not being set, if a capabilities request was done from idle. Move
the timeout value setting to before where that change might be
requested.
IMHO the cause here is the invisible returns in the macros. Maybe
that's a job for later, though.
The function __builtin_expect returns long type (see the gcc
documentation), and so do macros likely and unlikely. Unfortunatelly, when
CONFIG_PROFILE_ANNOTATED_BRANCHES is selected, the macros likely and
unlikely expand to __branch_check__ and __branch_check__ truncates the
long type to int. This unintended truncation may cause bugs in various
kernel code (we found a bug in dm-writecache because of it), so it's
better to fix __branch_check__ to return long.
ftrace_graph_caller was never run after calling ftrace_trace_function,
breaking the function graph tracer. Fix this, bringing it in line with the
x86 implementation.
While we're at it, also streamline the control flow of _mcount a bit to
reduce the number of branches.
This issue was reported before:
https://www.linux-mips.org/archives/linux-mips/2014-11/msg00295.html
"%pCr" formats the current rate of a clock, and calls clk_get_rate().
The latter obtains a mutex, hence it must not be called from atomic
context.
Remove support for this rarely-used format, as vsprintf() (and e.g.
printk()) must be callable from any context.
Any remaining out-of-tree users will start seeing the clock's name
printed instead of its rate.
Reported-by: Jia-Ju Bai <baijiaju1990@gmail.com> Fixes: 900cca2944254edd ("lib/vsprintf: add %pC{,n,r} format specifiers for clocks") Link: http://lkml.kernel.org/r/1527845302-12159-5-git-send-email-geert+renesas@glider.be
To: Jia-Ju Bai <baijiaju1990@gmail.com>
To: Jonathan Corbet <corbet@lwn.net>
To: Michael Turquette <mturquette@baylibre.com>
To: Stephen Boyd <sboyd@kernel.org>
To: Zhang Rui <rui.zhang@intel.com>
To: Eduardo Valentin <edubezval@gmail.com>
To: Eric Anholt <eric@anholt.net>
To: Stefan Wahren <stefan.wahren@i2se.com>
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: linux-doc@vger.kernel.org Cc: linux-clk@vger.kernel.org Cc: linux-pm@vger.kernel.org Cc: linux-serial@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Cc: linux-renesas-soc@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: Geert Uytterhoeven <geert+renesas@glider.be> Cc: stable@vger.kernel.org # 4.1+ Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Petr Mladek <pmladek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to "EP93xx User’s Guide", I2STXLinCtrlData and I2SRXLinCtrlData
registers actually have different format. The only currently used bit
(Left_Right_Justify) has different position. Fix this and simplify the
whole setup taking into account the fact that both registers have zero
default value.
The practical effect of the above is repaired SND_SOC_DAIFMT_RIGHT_J
support (currently unused).
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bit responsible for LRCLK polarity is i2s_tlrs (0), not i2s_trel (2)
(refer to "EP93xx User's Guide").
Previously card drivers which specified SND_SOC_DAIFMT_NB_IF actually got
SND_SOC_DAIFMT_NB_NF, an adaptation is necessary to retain the old
behavior.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some low-speed and full-speed devices (for example, bluetooth)
do not have time to initialize. For them, ETIMEDOUT is a valid error.
We need to give them another try. Otherwise, they will
never be initialized correctly and in dmesg will be messages
"Bluetooth: hci0 command 0x1002 tx timeout" or similars.
Fixes: 264904ccc33c ("usb: retry reset if a device times out") Cc: stable <stable@vger.kernel.org> Signed-off-by: Maxim Moseychuk <franchesko.salias.hudro.pedros@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While working on changing this code to use force_sig_fault I
discovered that do_unaliged_user is sets si_signo to SIGBUS and passes
SIGSEGV to force_sig_info. Which is just b0rked.
The code is reporting a SIGBUS error so replace the SIGSEGV with SIGBUS.
Cc: Chris Zankel <chris@zankel.net> Cc: Max Filippov <jcmvbkbc@gmail.com> Cc: linux-xtensa@linux-xtensa.org Cc: stable@vger.kernel.org Acked-by: Max Filippov <jcmvbkbc@gmail.com> Fixes: 5a0015d62668 ("[PATCH] xtensa: Architecture support for Tensilica Xtensa Part 3") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 40f70c03e33a ("serial: sh-sci: add locking to console write
function to avoid SMP lockup") copied the strategy to avoid locking
problems in conjuncture with the console from the UART8250
driver. Instead using directly spin_{try}lock_irqsave(),
local_irq_save() followed by spin_{try}lock() was used. While this is
correct on mainline, for -rt it is a problem. spin_{try}lock() will
check if it is running in a valid context. Since the local_irq_save()
has already been executed, the context has changed and
spin_{try}lock() will complain. The reason why spin_{try}lock()
complains is that on -rt the spin locks are turned into mutexes and
therefore can sleep. Sleeping with interrupts disabled is not valid.
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Daniel Wagner <daniel.wagner@siemens.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
[dw: Backported to 4.4.] Signed-off-by: Daniel Wagner <daniel.wagner@siemens.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If 020/030 support is enabled, get_io_area() leaves an IO_SIZE gap
between mappings which is added to the vm_struct representing the
mapping. __ioremap() uses the actual requested size (after alignment),
while __iounmap() is passed the size from the vm_struct.
On 020/030, early termination descriptors are used to set up mappings of
extent 'size', which are validated on unmapping. The unmapped gap of
size IO_SIZE defeats the sanity check of the pmd tables, causing
__iounmap() to loop forever on 030.
On 040/060, unmapping of page table entries does not check for a valid
mapping, so the umapping loop always completes there.
Adjust size to be unmapped by the gap that had been added in the
vm_struct prior.
This fixes the hang in atari_platform_init() reported a long time ago,
and a similar one reported by Finn recently (addressed by removing
ioremap() use from the SWIM driver.
Tested on my Falcon in 030 mode - untested but should work the same on
040/060 (the extra page tables cleared there would never have been set
up anyway).
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
[geert: Minor commit description improvements]
[geert: This was fixed in 2.4.23, but not in 2.5.x] Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Rutland noticed that GCC optimization passes have the potential to elide
necessary invocations of the array_index_mask_nospec() instruction sequence,
so mark the asm() volatile.
Mark explains:
"The volatile will inhibit *some* cases where the compiler could lift the
array_index_nospec() call out of a branch, e.g. where there are multiple
invocations of array_index_nospec() with the same arguments:
... since the compiler can determine that the two invocations yield the same
result, and reuse the first result (likely the same register as idx was in
originally) for the second branch, effectively re-writing the above as:
WHen registering a new binfmt_misc handler, it is possible to overflow
the offset to get a negative value, which might crash the system, or
possibly leak kernel data.
Here is a crash log when 2500000000 was used as an offset:
Use kstrtoint instead of simple_strtoul. It will work as the code
already set the delimiter byte to '\0' and we only do it when the field
is not empty.
Tested with offsets -1, 2500000000, UINT_MAX and INT_MAX. Also tested
with examples documented at Documentation/admin-guide/binfmt-misc.rst
and other registrations from packages on Ubuntu.
Link: http://lkml.kernel.org/r/20180529135648.14254-1-cascardo@canonical.com Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 184add2ca23c ("libata: Apply NOLPM quirk for SanDisk
SD7UB3Q*G1001 SSDs") disabled LPM for SanDisk SD7UB3Q*G1001 SSDs.
This has lead to several reports of users of that SSD where LPM
was working fine and who know have a significantly increased idle
power consumption on their laptops.
Likely there is another problem on the T450s from the original
reporter which gets exposed by the uncore reaching deeper sleep
states (higher PC-states) due to LPM being enabled. The problem as
reported, a hardfreeze about once a day, already did not sound like
it would be caused by LPM and the reports of the SSD working fine
confirm this. The original reporter is ok with dropping the quirk.
A X250 user has reported the same hard freeze problem and for him
the problem went away after unrelated updates, I suspect some GPU
driver stack changes fixed things.
TL;DR: The original reporters problem were triggered by LPM but not
an LPM issue, so drop the quirk for the SSD in question.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1583207 Cc: stable@vger.kernel.org Cc: Richard W.M. Jones <rjones@redhat.com> Cc: Lorenzo Dalrio <lorenzo.dalrio@gmail.com> Reported-by: Lorenzo Dalrio <lorenzo.dalrio@gmail.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Acked-by: "Richard W.M. Jones" <rjones@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't populate the arrays cdb on the stack, instead make them static.
Makes the object code smaller by 230 bytes:
Before:
text data bss dec hex filename
3797 240 0 4037 fc5 drivers/ata/libata-zpodd.o
After:
text data bss dec hex filename
3407 400 0 3807 edf drivers/ata/libata-zpodd.o
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the policy limits are updated via cpufreq_update_policy() and
subsequently via sysfs, the limits stored in user_policy may be
set incorrectly.
For example, if both min and max are set via sysfs to the maximum
available frequency, user_policy.min and user_policy.max will also
be the maximum. If a policy notifier triggered by
cpufreq_update_policy() lowers both the min and the max at this
point, that change is not reflected by the user_policy limits, so
if the max is updated again via sysfs to the same lower value,
then user_policy.max will be lower than user_policy.min which
shouldn't happen. In particular, if one of the policy CPUs is
then taken offline and back online, cpufreq_set_policy() will
fail for it due to a failing limits check.
To prevent that from happening, initialize the min and max fields
of the new_policy object to the ones stored in user_policy that
were previously set via sysfs.
Signed-off-by: Kevin Wangtao <kevin.wangtao@hisilicon.com> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw: Subject & changelog ] Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 'kzalloc()' fails in 'snd_hda_attach_pcm_stream()', a new pcm instance is
created without setting its operators via 'snd_pcm_set_ops()'. Following
operations on the new pcm instance can trigger kernel null pointer dereferences
and cause kernel oops.
This bug was found with my work on building a gray-box fault-injection tool for
linux-kernel-module binaries. A kernel null pointer dereference was confirmed
from line 'substream->ops->open()' in function 'snd_pcm_open_substream()' in
file 'sound/core/pcm_native.c'.
This patch fixes the bug by calling 'snd_device_free()' in the error handling
path of 'kzalloc()', which removes the new pcm instance from the snd card before
returns with an error code.
[BUG]
Btrfs can create compressed extent without checksum (even though it
shouldn't), and if we then try to replace device containing such extent,
the result device will contain all the uncompressed data instead of the
compressed one.
Test case already submitted to fstests:
https://patchwork.kernel.org/patch/10442353/
[CAUSE]
When handling compressed extent without checksum, device replace will
goe into copy_nocow_pages() function.
In that function, btrfs will get all inodes referring to this data
extents and then use find_or_create_page() to get pages direct from that
inode.
The problem here is, pages directly from inode are always uncompressed.
And for compressed data extent, they mismatch with on-disk data.
Thus this leads to corrupted compressed data extent written to replace
device.
[FIX]
In this attempt, we could just remove the "optimization" branch, and let
unified scrub_pages() to handle it.
Although scrub_pages() won't bother reusing page cache, it will be a
little slower, but it does the correct csum checking and won't cause
such data corruption caused by "optimization".
Note about the fix: this is the minimal fix that can be backported to
older stable trees without conflicts. The whole callchain from
copy_nocow_pages() can be deleted, and will be in followup patches.
Fixes: ff023aac3119 ("Btrfs: add code to scrub to copy read data to another disk") CC: stable@vger.kernel.org # 4.4+ Reported-by: James Harvey <jamespharvey20@gmail.com> Reviewed-by: James Harvey <jamespharvey20@gmail.com> Signed-off-by: Qu Wenruo <wqu@suse.com>
[ remove code removal, add note why ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is hitting WARN() at kernfs_add_one() [1].
This is because kernfs_create_link() is confused by previous device_add()
call which continued without setting dev->kobj.parent field when
get_device_parent() failed by memory allocation fault injection.
Fix this by propagating the error from class_dir_create_and_add() to
the calllers of get_device_parent().
ext4_resize_fs() has an off-by-one bug when checking whether growing of
a filesystem will not overflow inode count. As a result it allows a
filesystem with 8192 inodes per group to grow to 64TB which overflows
inode count to 0 and makes filesystem unusable. Fix it.
Cc: stable@vger.kernel.org Fixes: 3f8a6411fbada1fa482276591e037f3b1adcf55b Reported-by: Jaco Kroon <jaco@uls.co.za> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Andreas Dilger <adilger@dilger.ca> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently in ext4_punch_hole we're going to skip the mtime update if
there are no actual blocks to release. However we've actually modified
the file by zeroing the partial block so the mtime should be updated.
Moreover the sync and datasync handling is skipped as well, which is
also wrong. Fix it.
commit 079096f103fa ("tcp/dccp: install syn_recv requests into ehash
table") introduced an optimization for the handling of child sockets
created for a new TCP connection.
But this optimization passes any data associated with the last ACK of the
connection handshake up the stack without verifying its checksum, because it
calls tcp_child_process(), which in turn calls tcp_rcv_state_process()
directly. These lower-level processing functions do not do any checksum
verification.
Insert a tcp_checksum_complete call in the TCP_NEW_SYN_RECEIVE path to
fix this.
Fixes: 079096f103fa ("tcp/dccp: install syn_recv requests into ehash table") Signed-off-by: Frank van der Linden <fllinden@amazon.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Balbir Singh <bsingharora@gmail.com> Reviewed-by: Balbir Singh <bsingharora@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a timing issue under active-standy mode, when bond_enslave() is
called, bond->params.primary might not be initialized yet.
Any time the primary slave string changes, bond->force_primary should be
set to true to make sure the primary becomes the active slave.
Signed-off-by: Xiangning Yu <yuxiangning@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed that writing 0xF2 to the power register while it
reads as 0xF4 results in the register having the value 0xF0, i.e. clearing
RESUME and setting SUSPENDM in one go does not work. It might also violate
the USB spec to transition directly from resume to suspend, especially
when not taking T_DRSMDN into account. But this is what happens when a
remote wakeup occurs between SetPortFeature USB_PORT_FEAT_SUSPEND on the
root hub and musb_bus_suspend being called.
This commit returns -EBUSY when musb_bus_suspend is called while remote
wakeup is signalled and thus avoids to reset the RESUME bit. Ignoring
this error when musb_port_suspend is called from musb_hub_control is ok.
Signed-off-by: Daniel Glöckner <dg@emlix.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a scenario that can end up with rebuild process failing to
return good content, i.e.
suppose that all disks can be read without problems and if the content
that was read out doesn't match its checksum, currently for raid6
btrfs at most retries twice,
- the 1st retry is to rebuild with all other stripes, it'll eventually
be a raid5 xor rebuild,
- if the 1st fails, the 2nd retry will deliberately fail parity p so
that it will do raid6 style rebuild,
however, the chances are that another non-parity stripe content also
has something corrupted, so that the above retries are not able to
return correct content, and users will think of this as data loss.
More seriouly, if the loss happens on some important internal btree
roots, it could refuse to mount.
This extends btrfs to do more retries and each retry fails only one
stripe. Since raid6 can tolerate 2 disk failures, if there is one
more failure besides the failure on which we're recovering, this can
always work.
The worst case is to retry as many times as the number of raid6 disks,
but given the fact that such a scenario is really rare in practice,
it's still acceptable.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <alexander.levin@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log