It turns out that we should *not* invert all not-present mappings,
because the all zeroes case is obviously special.
clear_page() does not undergo the XOR logic to invert the address bits,
i.e. PTE, PMD and PUD entries that have not been individually written
will have val=0 and so will trigger __pte_needs_invert(). As a result,
{pte,pmd,pud}_pfn() will return the wrong PFN value, i.e. all ones
(adjusted by the max PFN mask) instead of zero. A zeroed entry is ok
because the page at physical address 0 is reserved early in boot
specifically to mitigate L1TF, so explicitly exempt them from the
inversion when reading the PFN.
Manifested as an unexpected mprotect(..., PROT_NONE) failure when called
on a VMA that has VM_PFNMAP and was mmap'd to as something other than
PROT_NONE but never used. mprotect() sends the PROT_NONE request down
prot_none_walk(), which walks the PTEs to check the PFNs.
prot_none_pte_entry() gets the bogus PFN from pte_pfn() and returns
-EACCES because it thinks mprotect() is trying to adjust a high MMIO
address.
[ This is a very modified version of Sean's original patch, but all
credit goes to Sean for doing this and also pointing out that
sometimes the __pte_needs_invert() function only gets the protection
bits, not the full eventual pte. But zero remains special even in
just protection bits, so that's ok. - Linus ]
Fixes: f22cc87f6c1f ("x86/speculation/l1tf: Invert all not present mappings") Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Acked-by: Andi Kleen <ak@linux.intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioremap() calls pud_free_pmd_page() / pmd_free_pte_page() when it creates
a pud / pmd map. The following preconditions are met at their entry.
- All pte entries for a target pud/pmd address range have been cleared.
- System-wide TLB purges have been peformed for a target pud/pmd address
range.
The preconditions assure that there is no stale TLB entry for the range.
Speculation may not cache TLB entries since it requires all levels of page
entries, including ptes, to have P & A-bits set for an associated address.
However, speculation may cache pud/pmd entries (paging-structure caches)
when they have P-bit set.
Add a system-wide TLB purge (INVLPG) to a single page after clearing
pud/pmd entry's P-bit.
SDM 4.10.4.1, Operation that Invalidate TLBs and Paging-Structure Caches,
states that:
INVLPG invalidates all paging-structure caches associated with the
current PCID regardless of the liner addresses to which they correspond.
The following kernel panic was observed on ARM64 platform due to a stale
TLB entry.
1. ioremap with 4K size, a valid pte page table is set.
2. iounmap it, its pte entry is set to 0.
3. ioremap the same address with 2M size, update its pmd entry with
a new value.
4. CPU may hit an exception because the old pmd entry is still in TLB,
which leads to a kernel panic.
Commit b6bdb7517c3d ("mm/vmalloc: add interfaces to free unmapped page
table") has addressed this panic by falling to pte mappings in the above
case on ARM64.
To support pmd mappings in all cases, TLB purge needs to be performed
in this case on ARM64.
Add a new arg, 'addr', to pud_free_pmd_page() and pmd_free_pte_page()
so that TLB purge can be added later in seprate patches.
The buffer length is unsigned at all layers, but gets cast to int and
checked in hidp_process_report and can lead to a buffer overflow.
Switch len parameter to unsigned int to resolve issue.
This affects 3.18 and newer kernels.
Signed-off-by: Mark Salyzyn <salyzyn@android.com> Fixes: a4b1b5877b514b276f0f31efe02388a9c2836728 ("HID: Bluetooth: hidp: make sure input buffers are big enough") Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Kees Cook <keescook@chromium.org> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: linux-bluetooth@vger.kernel.org Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Cc: security@kernel.org Cc: kernel-team@android.com Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ts3a227e audio accessory detection hardware is present and its
driver probed, the jack needs to be created before enabling jack
detection in the ts3a227e driver. With this patch, the jack is
instantiated in the max98090 headset init function if the ts3a227e is
present. This fixes a null pointer dereference as the jack detection
enabling function in the ts3a driver was called before the jack is
created.
[minor correction to keep error handling on jack creation the same
as before by Pierre Bossart]
scatterwalk_done() is only meant to be called after a nonzero number of
bytes have been processed, since scatterwalk_pagedone() will flush the
dcache of the *previous* page. But in the error case of
ablkcipher_walk_done(), e.g. if the input wasn't an integer number of
blocks, scatterwalk_done() was actually called after advancing 0 bytes.
This caused a crash ("BUG: unable to handle kernel paging request")
during '!PageSlab(page)' on architectures like arm and arm64 that define
ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE, provided that the input was
page-aligned as in that case walk->offset == 0.
Fix it by reorganizing ablkcipher_walk_done() to skip the
scatterwalk_advance() and scatterwalk_done() if an error has occurred.
Reported-by: Liu Chao <liuchao741@huawei.com> Fixes: bf06099db18a ("crypto: skcipher - Add ablkcipher_walk interfaces") Cc: <stable@vger.kernel.org> # v2.6.35+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
scatterwalk_done() is only meant to be called after a nonzero number of
bytes have been processed, since scatterwalk_pagedone() will flush the
dcache of the *previous* page. But in the error case of
blkcipher_walk_done(), e.g. if the input wasn't an integer number of
blocks, scatterwalk_done() was actually called after advancing 0 bytes.
This caused a crash ("BUG: unable to handle kernel paging request")
during '!PageSlab(page)' on architectures like arm and arm64 that define
ARCH_IMPLEMENTS_FLUSH_DCACHE_PAGE, provided that the input was
page-aligned as in that case walk->offset == 0.
Fix it by reorganizing blkcipher_walk_done() to skip the
scatterwalk_advance() and scatterwalk_done() if an error has occurred.
syzbot reported a crash in vmac_final() when multiple threads
concurrently use the same "vmac(aes)" transform through AF_ALG. The bug
is pretty fundamental: the VMAC template doesn't separate per-request
state from per-tfm (per-key) state like the other hash algorithms do,
but rather stores it all in the tfm context. That's wrong.
Also, vmac_final() incorrectly zeroes most of the state including the
derived keys and cached pseudorandom pad. Therefore, only the first
VMAC invocation with a given key calculates the correct digest.
Fix these bugs by splitting the per-tfm state from the per-request state
and using the proper init/update/final sequencing for requests.
The VMAC template assumes the block cipher has a 128-bit block size, but
it failed to check for that. Thus it was possible to instantiate it
using a 64-bit block size cipher, e.g. "vmac(cast5)", causing
uninitialized memory to be used.
Add the needed check when instantiating the template.
Fixes: f1939f7c5645 ("crypto: vmac - New hash algorithm for intel_txt support") Cc: <stable@vger.kernel.org> # v2.6.32+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi> Cc: Lucas De Marchi <lucas.de.marchi@gmail.com> Cc: Michal Marek <michal.lkml@markovi.net> Cc: Jessica Yu <jeyu@kernel.org> Cc: Chih-Wei Huang <cwhuang@linux.org.tw> Cc: stable@vger.kernel.org # any kernel since 2012 Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With KASAN enabled the kernel has two different memset() functions, one
with KASAN checks (memset) and one without (__memset). KASAN uses some
macro tricks to use the proper version where required. For example
memset() calls in mm/slub.c are without KASAN checks, since they operate
on poisoned slab object metadata.
The issue is that clang emits memset() calls even when there is no
memset() in the source code. They get linked with improper memset()
implementation and the kernel fails to boot due to a huge amount of KASAN
reports during early boot stages.
The solution is to add -fno-builtin flag for files with KASAN_SANITIZE :=
n marker.
Link: http://lkml.kernel.org/r/8ffecfffe04088c52c42b92739c2bd8a0bcb3f5e.1516384594.git.andreyknvl@google.com Signed-off-by: Andrey Konovalov <andreyknvl@google.com> Acked-by: Nick Desaulniers <ndesaulniers@google.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Cc: Michal Marek <michal.lkml@markovi.net> Cc: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Alexander Potapenko <glider@google.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ Nick : Backported to 4.4 avoiding KUBSAN ] Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Takashi Iwai [Wed, 15 Aug 2018 09:58:46 +0000 (11:58 +0200)]
tcp: Fix missing range_truesize enlargement in the backport
The 4.4.y stable backport dc6ae4dffd65 for the upstream commit 3d4bf93ac120 ("tcp: detect malicious patterns in
tcp_collapse_ofo_queue()") missed a line that enlarges the
range_truesize value, which broke the whole check.
Fixes: dc6ae4dffd65 ("tcp: detect malicious patterns in tcp_collapse_ofo_queue()") Signed-off-by: Takashi Iwai <tiwai@suse.de> Cc: Michal Kubecek <mkubecek@suse.cz>
ioremap() supports pmd mappings on x86-PAE. However, kernel's pmd
tables are not shared among processes on x86-PAE. Therefore, any
update to sync'd pmd entries need re-syncing. Freeing a pte page
also leads to a vmalloc fault and hits the BUG_ON in vmalloc_sync_one().
Disable free page handling on x86-PAE. pud_free_pmd_page() and
pmd_free_pte_page() simply return 0 if a given pud/pmd entry is present.
This assures that ioremap() does not update sync'd pmd entries at the
cost of falling back to pte mappings.
pfn_modify_allowed() and arch_has_pfn_modify_check() are outside of the
!__ASSEMBLY__ section in include/asm-generic/pgtable.h, which confuses
assembler on archs that don't have __HAVE_ARCH_PFN_MODIFY_ALLOWED (e.g.
ia64) and breaks build:
include/asm-generic/pgtable.h: Assembler messages:
include/asm-generic/pgtable.h:538: Error: Unknown opcode `static inline bool pfn_modify_allowed(unsigned long pfn,pgprot_t prot)'
include/asm-generic/pgtable.h:540: Error: Unknown opcode `return true'
include/asm-generic/pgtable.h:543: Error: Unknown opcode `static inline bool arch_has_pfn_modify_check(void)'
include/asm-generic/pgtable.h:545: Error: Unknown opcode `return false'
arch/ia64/kernel/entry.S:69: Error: `mov' does not fit into bundle
Move those two static inlines into the !__ASSEMBLY__ section so that they
don't confuse the asm build pass.
Fixes: 42e4089c7890 ("x86/speculation/l1tf: Disallow non privileged high MMIO PROT_NONE mappings") Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[groeck: Context changes] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The introduction of generic_max_swapfile_size and arch-specific versions has
broken linking on x86 with CONFIG_SWAP=n due to undefined reference to
'generic_max_swapfile_size'. Fix it by compiling the x86-specific
max_swapfile_size() only with CONFIG_SWAP=y.
Guenter Roeck [Mon, 13 Aug 2018 17:15:16 +0000 (10:15 -0700)]
x86/speculation/l1tf: Fix up CPU feature flags
In linux-4.4.y, the definition of X86_FEATURE_RETPOLINE and
X86_FEATURE_RETPOLINE_AMD is different from the upstream
definition. Result is an overlap with the newly introduced
X86_FEATURE_L1TF_PTEINV. Update RETPOLINE definitions to match
upstream definitions to improve alignment with upstream code.
The mmio tracer sets io mapping PTEs and PMDs to non present when enabled
without inverting the address bits, which makes the PTE entry vulnerable
for L1TF.
Make it use the right low level macros to actually invert the address bits
to protect against L1TF.
In principle this could be avoided because MMIO tracing is not likely to be
enabled on production machines, but the fix is straigt forward and for
consistency sake it's better to get rid of the open coded PTE manipulation.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_memory_np() is used to mark kernel mappings not present, but it has
it's own open coded mechanism which does not have the L1TF protection of
inverting the address bits.
Replace the open coded PTE manipulation with the L1TF protecting low level
PTE routines.
Passes the CPA self test.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[ dwmw2: Pull in pud_mkhuge() from commit a00cc7d9dd, and pfn_pud() ] Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
[groeck: port to 4.4] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some cases in THP like:
- MADV_FREE
- mprotect
- split
mark the PMD non present for temporarily to prevent races. The window for
an L1TF attack in these contexts is very small, but it wants to be fixed
for correctness sake.
Use the proper low level functions for pmd/pud_mknotpresent() to address
this.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For kernel mappings PAGE_PROTNONE is not necessarily set for a non present
mapping, but the inversion logic explicitely checks for !PRESENT and
PROT_NONE.
Remove the PROT_NONE check and make the inversion unconditional for all not
present mappings.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan has noticed that pte_pfn and co. resp. pfn_pte are incorrect for
CONFIG_PAE because phys_addr_t is wider than unsigned long and so the
pte_val reps. shift left would get truncated. Fix this up by using proper
types.
[dwmw2: Backport to 4.9]
Fixes: 6b28baca9b1f ("x86/speculation/l1tf: Protect PROT_NONE PTEs against speculation") Reported-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PAE 3-level paging code currently doesn't mitigate L1TF by flipping the
offset bits, and uses the high PTE word, thus bits 32-36 for type, 37-63 for
offset. The lower word is zeroed, thus systems with less than 4GB memory are
safe. With 4GB to 128GB the swap type selects the memory locations vulnerable
to L1TF; with even more memory, also the swap offfset influences the address.
This might be a problem with 32bit PAE guests running on large 64bit hosts.
By continuing to keep the whole swap entry in either high or low 32bit word of
PTE we would limit the swap size too much. Thus this patch uses the whole PAE
PTE with the same layout as the 64bit version does. The macros just become a
bit tricky since they assume the arch-dependent swp_entry_t to be 32bit.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Michal Hocko <mhocko@suse.com> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the L1TF workaround its necessary to limit the swap file size to below
MAX_PA/2, so that the higher bits of the swap offset inverted never point
to valid memory.
Add a mechanism for the architecture to override the swap file size check
in swapfile.c and add a x86 specific max swapfile check function that
enforces that limit.
The check is only enabled if the CPU is vulnerable to L1TF.
In VMs with 42bit MAX_PA the typical limit is 2TB now, on a native system
with 46bit PA it is 32TB. The limit is only per individual swap file, so
it's always possible to exceed these limits with multiple swap files or
partitions.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For L1TF PROT_NONE mappings are protected by inverting the PFN in the page
table entry. This sets the high bits in the CPU's address space, thus
making sure to point to not point an unmapped entry to valid cached memory.
Some server system BIOSes put the MMIO mappings high up in the physical
address space. If such an high mapping was mapped to unprivileged users
they could attack low memory by setting such a mapping to PROT_NONE. This
could happen through a special device driver which is not access
protected. Normal /dev/mem is of course access protected.
To avoid this forbid PROT_NONE mappings or mprotect for high MMIO mappings.
Valid page mappings are allowed because the system is then unsafe anyways.
It's not expected that users commonly use PROT_NONE on MMIO. But to
minimize any impact this is only enforced if the mapping actually refers to
a high MMIO address (defined as the MAX_PA-1 bit being set), and also skip
the check for root.
For mmaps this is straight forward and can be handled in vm_insert_pfn and
in remap_pfn_range().
For mprotect it's a bit trickier. At the point where the actual PTEs are
accessed a lot of state has been changed and it would be difficult to undo
on an error. Since this is a uncommon case use a separate early page talk
walk pass for MMIO PROT_NONE mappings that checks for this condition
early. For non MMIO and non PROT_NONE there are no changes.
[dwmw2: Backport to 4.9]
[groeck: Backport to 4.4]
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vm_insert_mixed() unlike vm_insert_pfn_prot() and vmf_insert_pfn_pmd(),
fails to check the pgprot_t it uses for the mapping against the one
recorded in the memtype tracking tree. Add the missing call to
track_pfn_insert() to preclude cases where incompatible aliased mappings
are established for a given physical address range.
[groeck: Backport to v4.4.y]
Link: http://lkml.kernel.org/r/147328717909.35069.14256589123570653697.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Cc: David Airlie <airlied@linux.ie> Cc: Matthew Wilcox <mawilcox@microsoft.com> Cc: Ross Zwisler <ross.zwisler@linux.intel.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The x86 vvar vma contains pages with differing cacheability
flags. x86 currently implements this by manually inserting all
the ptes using (io_)remap_pfn_range when the vma is set up.
x86 wants to move to using .fault with VM_FAULT_NOPAGE to set up
the mappings as needed. The correct API to use to insert a pfn
in .fault is vm_insert_pfn(), but vm_insert_pfn() can't override the
vma's cache mode, and the HPET page in particular needs to be
uncached despite the fact that the rest of the VMA is cached.
Add vm_insert_pfn_prot() to support varying cacheability within
the same non-COW VMA in a more sane manner.
x86 could alternatively use multiple VMAs, but that's messy,
would break CRIU, and would create unnecessary VMAs that would
waste memory.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Dave Hansen <dave.hansen@linux.intel.com> Cc: Fenghua Yu <fenghua.yu@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/d2938d1eb37be7a5e4f86182db646551f11e45aa.1451446564.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
L1TF core kernel workarounds are cheap and normally always enabled, However
they still should be reported in sysfs if the system is vulnerable or
mitigated. Add the necessary CPU feature/bug bits.
- Extend the existing checks for Meltdowns to determine if the system is
vulnerable. All CPUs which are not vulnerable to Meltdown are also not
vulnerable to L1TF
- Check for 32bit non PAE and emit a warning as there is no practical way
for mitigation due to the limited physical address bits
- If the system has more than MAX_PA/2 physical memory the invert page
workarounds don't protect the system against the L1TF attack anymore,
because an inverted physical address will also point to valid
memory. Print a warning in this case and report that the system is
vulnerable.
Add a function which returns the PFN limit for the L1TF mitigation, which
will be used in follow up patches for sanity and range checks.
[ tglx: Renamed the CPU feature bit to L1TF_PTEINV ]
[ dwmw2: Backport to 4.9 (cpufeatures.h, E820) ]
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The L1TF workaround doesn't make any attempt to mitigate speculate accesses
to the first physical page for zeroed PTEs. Normally it only contains some
data from the early real mode BIOS.
It's not entirely clear that the first page is reserved in all
configurations, so add an extra reservation call to make sure it is really
reserved. In most configurations (e.g. with the standard reservations)
it's likely a nop.
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PTEs are set to PROT_NONE the kernel just clears the Present bit and
preserves the PFN, which creates attack surface for L1TF speculation
speculation attacks.
This is important inside guests, because L1TF speculation bypasses physical
page remapping. While the host has its own migitations preventing leaking
data from other VMs into the guest, this would still risk leaking the wrong
page inside the current guest.
This uses the same technique as Linus' swap entry patch: while an entry is
is in PROTNONE state invert the complete PFN part part of it. This ensures
that the the highest bit will point to non existing memory.
The invert is done by pte/pmd_modify and pfn/pmd/pud_pte for PROTNONE and
pte/pmd/pud_pfn undo it.
This assume that no code path touches the PFN part of a PTE directly
without using these primitives.
This doesn't handle the case that MMIO is on the top of the CPU physical
memory. If such an MMIO region was exposed by an unpriviledged driver for
mmap it would be possible to attack some real memory. However this
situation is all rather unlikely.
For 32bit non PAE the inversion is not done because there are really not
enough bits to protect anything.
Q: Why does the guest need to be protected when the HyperVisor already has
L1TF mitigations?
A: Here's an example:
Physical pages 1 2 get mapped into a guest as
GPA 1 -> PA 2
GPA 2 -> PA 1
through EPT.
The L1TF speculation ignores the EPT remapping.
Now the guest kernel maps GPA 1 to process A and GPA 2 to process B, and
they belong to different users and should be isolated.
A sets the GPA 1 PA 2 PTE to PROT_NONE to bypass the EPT remapping and
gets read access to the underlying physical page. Which in this case
points to PA 2, so it can read process B's data, if it happened to be in
L1, so isolation inside the guest is broken.
There's nothing the hypervisor can do about this. This mitigation has to
be done in the guest itself.
With L1 terminal fault the CPU speculates into unmapped PTEs, and resulting
side effects allow to read the memory the PTE is pointing too, if its
values are still in the L1 cache.
For swapped out pages Linux uses unmapped PTEs and stores a swap entry into
them.
To protect against L1TF it must be ensured that the swap entry is not
pointing to valid memory, which requires setting higher bits (between bit
36 and bit 45) that are inside the CPUs physical address space, but outside
any real memory.
To do this invert the offset to make sure the higher bits are always set,
as long as the swap file is not too big.
Note there is no workaround for 32bit !PAE, or on systems which have more
than MAX_PA/2 worth of memory. The later case is very unlikely to happen on
real systems.
[AK: updated description and minor tweaks by. Split out from the original
patch ]
If pages are swapped out, the swap entry is stored in the corresponding
PTE, which has the Present bit cleared. CPUs vulnerable to L1TF speculate
on PTE entries which have the present bit set and would treat the swap
entry as phsyical address (PFN). To mitigate that the upper bits of the PTE
must be set so the PTE points to non existent memory.
The swap entry stores the type and the offset of a swapped out page in the
PTE. type is stored in bit 9-13 and offset in bit 14-63. The hardware
ignores the bits beyond the phsyical address space limit, so to make the
mitigation effective its required to start 'offset' at the lowest possible
bit so that even large swap offsets do not reach into the physical address
space limit bits.
Move offset to bit 9-58 and type to bit 59-63 which are the bits that
hardware generally doesn't care about.
That, in turn, means that if you on desktop chip with only 40 bits of
physical addressing, now that the offset starts at bit 9, there needs to be
30 bits of offset actually *in use* until bit 39 ends up being set, which
means when inverted it will again point into existing memory.
So that's 4 terabyte of swap space (because the offset is counted in pages,
so 30 bits of offset is 42 bits of actual coverage). With bigger physical
addressing, that obviously grows further, until the limit of the offset is
hit (at 50 bits of offset - 62 bits of actual swap file coverage).
This is a preparatory change for the actual swap entry inversion to protect
against L1TF.
[ AK: Updated description and minor tweaks. Split into two parts ]
[ tglx: Massaged changelog ]
_PAGE_PSE is used to distinguish between a truly non-present
(_PAGE_PRESENT=0) PMD, and a PMD which is undergoing a THP split and
should be treated as present.
But _PAGE_SWP_SOFT_DIRTY currently uses the _PAGE_PSE bit, which would
cause confusion between one of those PMDs undergoing a THP split, and a
soft-dirty PMD. Dropping _PAGE_PSE check in pmd_present() does not work
well, because it can hurt optimization of tlb handling in thp split.
Thus, we need to move the bit.
In the current kernel, bits 1-4 are not used in non-present format since
commit 00839ee3b299 ("x86/mm: Move swap offset/type up in PTE to work
around erratum"). So let's move _PAGE_SWP_SOFT_DIRTY to bit 1. Bit 7
is used as reserved (always clear), so please don't use it for other
purpose.
[dwmw2: Pulled in to 4.9 backport to support L1TF changes]
Link: http://lkml.kernel.org/r/20170717193955.20207-3-zi.yan@sent.com Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Signed-off-by: Zi Yan <zi.yan@cs.rutgers.edu> Acked-by: Dave Hansen <dave.hansen@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com> Cc: David Nellans <dnellans@nvidia.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Cc: Mel Gorman <mgorman@techsingularity.net> Cc: Minchan Kim <minchan@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Michal Hocko <mhocko@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment explaining the format of the swap PTE is wrong about
the bits used for the swap type field. Amusingly, the ASCII art
and the patch description are correct, but the comment itself
is wrong.
As I was looking at this, I also noticed that the
SWP_OFFSET_FIRST_BIT has an off-by-one error. This does not
really hurt anything. It just wasted a bit of space in the PTE,
giving us 2^59 bytes of addressable space in our swapfiles
instead of 2^60. But, it doesn't match with the comments, and it
wastes a bit of space, so fix it.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave@sr71.net> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Fixes: 00839ee3b299 ("x86/mm: Move swap offset/type up in PTE to work around erratum") Link: http://lkml.kernel.org/r/20160810172325.E56AD7DA@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This erratum can result in Accessed/Dirty getting set by the hardware
when we do not expect them to be (on !Present PTEs).
Instead of trying to fix them up after this happens, we just
allow the bits to get set and try to ignore them. We do this by
shifting the layout of the bits we use for swap offset/type in
our 64-bit PTEs.
Note that D was already a don't care (X) even before. We just
move TYPE up and turn its old spot (which could be hit by the
A bit) into all don't cares.
We take 5 bits away from the offset, but that still leaves us
with 50 bits which lets us index into a 62-bit swapfile (4 EiB).
I think that's probably fine for the moment. We could
theoretically reclaim 5 of the bits (1, 2, 3, 4, 7) but it
doesn't gain us anything.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Dave Hansen <dave@sr71.net> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Luis R. Rodriguez <mcgrof@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Toshi Kani <toshi.kani@hp.com> Cc: dave.hansen@intel.com Cc: linux-mm@kvack.org Cc: mhocko@suse.com Link: http://lkml.kernel.org/r/20160708001911.9A3FD2B6@viggo.jf.intel.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
L1 Terminal Fault (L1TF) is a speculation related vulnerability. The CPU
speculates on PTE entries which do not have the PRESENT bit set, if the
content of the resulting physical address is available in the L1D cache.
The OS side mitigation makes sure that a !PRESENT PTE entry points to a
physical address outside the actually existing and cachable memory
space. This is achieved by inverting the upper bits of the PTE. Due to the
address space limitations this only works for 64bit and 32bit PAE kernels,
but not for 32bit non PAE.
This mitigation applies to both host and guest kernels, but in case of a
64bit host (hypervisor) and a 32bit PAE guest, inverting the upper bits of
the PAE address space (44bit) is not enough if the host has more than 43
bits of populated memory address space, because the speculation treats the
PTE content as a physical host address bypassing EPT.
The host (hypervisor) protects itself against the guest by flushing L1D as
needed, but pages inside the guest are not protected against attacks from
other processes inside the same guest.
For the guest the inverted PTE mask has to match the host to provide the
full protection for all pages the host could possibly map into the
guest. The hosts populated address space is not known to the guest, so the
mask must cover the possible maximal host address space, i.e. 52 bit.
On 32bit PAE the maximum PTE mask is currently set to 44 bit because that
is the limit imposed by 32bit unsigned long PFNs in the VMs. This limits
the mask to be below what the host could possible use for physical pages.
The L1TF PROT_NONE protection code uses the PTE masks to determine which
bits to invert to make sure the higher bits are set for unmapped entries to
prevent L1TF speculation attacks against EPT inside guests.
In order to invert all bits that could be used by the host, increase
__PHYSICAL_PAGE_SHIFT to 52 to match 64bit.
The real limit for a 32bit PAE kernel is still 44 bits because all Linux
PTEs are created from unsigned long PFNs, so they cannot be higher than 44
bits on a 32bit kernel. So these extra PFN bits should be never set. The
only users of this macro are using it to look at PTEs, so it's safe.
[ tglx: Massaged changelog ]
Signed-off-by: Andi Kleen <ak@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: Dave Hansen <dave.hansen@intel.com> Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The article "Spectre Returns! Speculation Attacks using the Return Stack
Buffer" [1] describes two new (sub-)variants of spectrev2-like attacks,
making use solely of the RSB contents even on CPUs that don't fallback to
BTB on RSB underflow (Skylake+).
Mitigate userspace-userspace attacks by always unconditionally filling RSB on
context switch when the generic spectrev2 mitigation has been enabled.
[1] https://arxiv.org/pdf/1807.07940.pdf
Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com> Acked-by: Tim Chen <tim.c.chen@linux.intel.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Borislav Petkov <bp@suse.de> Cc: David Woodhouse <dwmw@amazon.co.uk> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/nycvar.YFH.7.76.1807261308190.997@cbobk.fhfr.pm Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nadav reported that on guests we're failing to rewrite the indirect
calls to CALLEE_SAVE paravirt functions. In particular the
pv_queued_spin_unlock() call is left unpatched and that is all over the
place. This obviously wrecks Spectre-v2 mitigation (for paravirt
guests) which relies on not actually having indirect calls around.
The reason is an incorrect clobber test in paravirt_patch_call(); this
function rewrites an indirect call with a direct call to the _SAME_
function, there is no possible way the clobbers can be different
because of this.
Therefore remove this clobber check. Also put WARNs on the other patch
failure case (not enough room for the instruction) which I've not seen
trigger in my (limited) testing.
Three live kernel image disassemblies for lock_sock_nested (as a small
function that illustrates the problem nicely). PRE is the current
situation for guests, POST is with this patch applied and NATIVE is with
or without the patch for !guests.
Use the correct IRQ line for the MSI controller in the PCIe host
controller. Apparently a different IRQ line is used compared to other
i.MX6 variants. Without this change MSI IRQs aren't properly propagated
to the upstream interrupt controller.
In write to debugfs file 'resource_stats' the local buffer 'tmp_str' is
written at index 'count-1' where 'count' is the size of the write, so
potentially 0.
This patch filters odd values for the write size/position to avoid this
type of problem.
Signed-off-by: Michael Mera <dev@michaelmera.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow rereg_user_mr to modify the MR from read-only to writable without
using get_user_pages again, we needed to define the initial MR as writable.
However, this was originally done unconditionally, without taking into
account the writability of the underlying virtual memory.
As a result, any attempt to register a read-only MR over read-only
virtual memory failed.
To fix this, do not add the writable flag bit when the user virtual memory
is not writable (e.g. const memory).
However, when the underlying memory is NOT writable (and we therefore
do not define the initial MR as writable), the IB core adds a
"force writable" flag to its user-pages request. If this succeeds,
the reg_user_mr caller gets a writable copy of the original pages.
If the user-space caller then does a rereg_user_mr operation to enable
writability, this will succeed. This should not be allowed, since
the original virtual memory was not writable.
Cc: <stable@vger.kernel.org> Fixes: 9376932d0c26 ("IB/mlx4_ib: Add support for user MR re-registration") Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__legitimize_mnt() has two problems - one is that in case of success
the check of mount_lock is not ordered wrt preceding increment of
refcount, making it possible to have successful __legitimize_mnt()
on one CPU just before the otherwise final mntpu() on another,
with __legitimize_mnt() not seeing mntput() taking the lock and
mntput() not seeing the increment done by __legitimize_mnt().
Solved by a pair of barriers.
Another is that failure of __legitimize_mnt() on the second
read_seqretry() leaves us with reference that'll need to be
dropped by caller; however, if that races with final mntput()
we can end up with caller dropping rcu_read_lock() and doing
mntput() to release that reference - with the first mntput()
having freed the damn thing just as rcu_read_lock() had been
dropped. Solution: in "do mntput() yourself" failure case
grab mount_lock, check if MNT_DOOMED has been set by racing
final mntput() that has missed our increment and if it has -
undo the increment and treat that as "failure, caller doesn't
need to drop anything" case.
It's not easy to hit - the final mntput() has to come right
after the first read_seqretry() in __legitimize_mnt() *and*
manage to miss the increment done by __legitimize_mnt() before
the second read_seqretry() in there. The things that are almost
impossible to hit on bare hardware are not impossible on SMP
KVM, though...
mntput_no_expire() does the calculation of total refcount under mount_lock;
unfortunately, the decrement (as well as all increments) are done outside
of it, leading to false positives in the "are we dropping the last reference"
test. Consider the following situation:
* mnt is a lazy-umounted mount, kept alive by two opened files. One
of those files gets closed. Total refcount of mnt is 2. On CPU 42
mntput(mnt) (called from __fput()) drops one reference, decrementing component
* After it has looked at component #0, the process on CPU 0 does
mntget(), incrementing component #0, gets preempted and gets to run again -
on CPU 69. There it does mntput(), which drops the reference (component #69)
and proceeds to spin on mount_lock.
* On CPU 42 our first mntput() finishes counting. It observes the
decrement of component #69, but not the increment of component #0. As the
result, the total it gets is not 1 as it should've been - it's 0. At which
point we decide that vfsmount needs to be killed and proceed to free it and
shut the filesystem down. However, there's still another opened file
on that filesystem, with reference to (now freed) vfsmount, etc. and we are
screwed.
It's not a wide race, but it can be reproduced with artificial slowdown of
the mnt_get_count() loop, and it should be easier to hit on SMP KVM setups.
Fix consists of moving the refcount decrement under mount_lock; the tricky
part is that we want (and can) keep the fast case (i.e. mount that still
has non-NULL ->mnt_ns) entirely out of mount_lock. All places that zero
mnt->mnt_ns are dropping some reference to mnt and they call synchronize_rcu()
before that mntput(). IOW, if mntput() observes (under rcu_read_lock())
a non-NULL ->mnt_ns, it is guaranteed that there is another reference yet to
be dropped.
Since mountpoint crossing can happen without leaving lazy mode,
root dentries do need the same protection against having their
memory freed without RCU delay as everything else in the tree.
It's partially hidden by RCU delay between detaching from the
mount tree and dropping the vfsmount reference, but the starting
point of pathwalk can be on an already detached mount, in which
case umount-caused RCU delay has already passed by the time the
lazy pathwalk grabs rcu_read_lock(). If the starting point
happens to be at the root of that vfsmount *and* that vfsmount
covers the entire filesystem, we get trouble.
Surround scsi_execute() calls with scsi_autopm_get_device() and
scsi_autopm_put_device(). Note: removing sr_mutex protection from the
scsi_cd_get() and scsi_cd_put() calls is safe because the purpose of
sr_mutex is to serialize cdrom_*() calls.
This patch avoids that complaints similar to the following appear in the
kernel log if runtime power management is enabled:
INFO: task systemd-udevd:650 blocked for more than 120 seconds.
Not tainted 4.18.0-rc7-dbg+ #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
systemd-udevd D28176 650 513 0x00000104
Call Trace:
__schedule+0x444/0xfe0
schedule+0x4e/0xe0
schedule_preempt_disabled+0x18/0x30
__mutex_lock+0x41c/0xc70
mutex_lock_nested+0x1b/0x20
__blkdev_get+0x106/0x970
blkdev_get+0x22c/0x5a0
blkdev_open+0xe9/0x100
do_dentry_open.isra.19+0x33e/0x570
vfs_open+0x7c/0xd0
path_openat+0x6e3/0x1120
do_filp_open+0x11c/0x1c0
do_sys_open+0x208/0x2d0
__x64_sys_openat+0x59/0x70
do_syscall_64+0x77/0x230
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com> Cc: Maurizio Lombardi <mlombard@redhat.com> Cc: Johannes Thumshirn <jthumshirn@suse.de> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: <stable@vger.kernel.org> Tested-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The LPSS PWM device on on Bay Trail and Cherry Trail devices has a set
of private registers at offset 0x800, the current lpss_device_desc for
them already sets the LPSS_SAVE_CTX flag to have these saved/restored
over device-suspend, but the current lpss_device_desc was not setting
the prv_offset field, leading to the regular device registers getting
saved/restored instead.
This is causing the PWM controller to no longer work, resulting in a black
screen, after a suspend/resume on systems where the firmware clears the
APB clock and reset bits at offset 0x804.
This commit fixes this by properly setting prv_offset to 0x800 for
the PWM devices.
skb_shinfo() can change when calling __pskb_pull_tail(): Don't cache
its return value.
Cc: stable@vger.kernel.org Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For years I thought all parisc machines executed loads and stores in
order. However, Jeff Law recently indicated on gcc-patches that this is
not correct. There are various degrees of out-of-order execution all the
way back to the PA7xxx processor series (hit-under-miss). The PA8xxx
series has full out-of-order execution for both integer operations, and
loads and stores.
This is described in the following article:
http://web.archive.org/web/20040214092531/http://www.cpus.hp.com/technical_references/advperf.shtml
For this reason, we need to define mb() and to insert a memory barrier
before the store unlocking spinlocks. This ensures that all memory
accesses are complete prior to unlocking. The ldcw instruction performs
the same function on entry.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Cc: stable@vger.kernel.org # 4.0+ Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable the -mlong-calls compiler option by default, because otherwise in most
cases linking the vmlinux binary fails due to truncations of R_PARISC_PCREL22F
relocations. This fixes building the 64-bit defconfig.
One of the classes of kernel stack content leaks[1] is exposing the
contents of prior heap or stack contents when a new process stack is
allocated. Normally, those stacks are not zeroed, and the old contents
remain in place. In the face of stack content exposure flaws, those
contents can leak to userspace.
Fixing this will make the kernel no longer vulnerable to these flaws, as
the stack will be wiped each time a stack is assigned to a new process.
There's not a meaningful change in runtime performance; it almost looks
like it provides a benefit.
It continues to look like it's faster, though the deviation is rather
wide, but I'm not sure what I could do that would be less noisy. I'm
open to ideas!
Link: http://lkml.kernel.org/r/20180221021659.GA37073@beast Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: Laura Abbott <labbott@redhat.com> Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk> Cc: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ Srivatsa: Backported to 4.4.y ] Signed-off-by: Srivatsa S. Bhat <srivatsa@csail.mit.edu> Reviewed-by: Srinidhi Rao <srinidhir@vmware.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ESP algorithms using CBC mode require echainiv. Hence INET*_ESP have
to select CRYPTO_ECHAINIV in order to work properly. This solves the
issues caused by a misconfiguration as described in [1].
The original approach, patching crypto/Kconfig was turned down by
Herbert Xu [2].
Signed-off-by: Thomas Egerer <hakke_007@gmx.de> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Yongqin Liu <yongqin.liu@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race condition in tpm_common_write function allowing
two threads on the same /dev/tpm<N>, or two different applications
on the same /dev/tpmrm<N> to overwrite each other commands/responses.
Fixed this by taking the priv->buffer_mutex early in the function.
Also converted the priv->data_pending from atomic to a regular size_t
type. There is no need for it to be atomic since it is only touched
under the protection of the priv->buffer_mutex.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com> Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8844618d8aa7: "ext4: only look at the bg_flags field if it is
valid" will complain if block group zero does not have the
EXT4_BG_INODE_ZEROED flag set. Unfortunately, this is not correct,
since a freshly created file system has this flag cleared. It gets
almost immediately after the file system is mounted read-write --- but
the following somewhat unlikely sequence will end up triggering a
false positive report of a corrupted file system:
mkfs.ext4 /dev/vdc
mount -o ro /dev/vdc /vdc
mount -o remount,rw /dev/vdc
Instead, when initializing the inode table for block group zero, test
to make sure that itable_unused count is not too large, since that is
the case that will result in some or all of the reserved inodes
getting cleared.
This fixes the failures reported by Eric Whiteney when running
generic/230 and generic/231 in the the nojournal test case.
Fixes: 8844618d8aa7 ("ext4: only look at the bg_flags field if it is valid") Reported-by: Eric Whitney <enwlinux@gmail.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to call reinit_completion() before dma is started to avoid race
condition where reinit_completion() is called after complete() and before
wait_for_completion_timeout().
Maintain the tracing on/off setting of the ring_buffer when switching
to the trace buffer snapshot.
Taking a snapshot is done by swapping the backup ring buffer
(max_tr_buffer). But since the tracing on/off setting is defined
by the ring buffer, when swapping it, the tracing on/off setting
can also be changed. This causes a strange result like below:
We don't touch tracing_on, but snapshot changes tracing_on
setting each time. This is an anomaly, because user doesn't know
that each "ring_buffer" stores its own tracing-enable state and
the snapshot is done by swapping ring buffers.
Link: http://lkml.kernel.org/r/153149929558.11274.11730609978254724394.stgit@devbox Cc: Ingo Molnar <mingo@redhat.com> Cc: Shuah Khan <shuah@kernel.org> Cc: Tom Zanussi <tom.zanussi@linux.intel.com> Cc: Hiraku Toyooka <hiraku.toyooka@cybertrust.co.jp> Cc: stable@vger.kernel.org Fixes: debdd57f5145 ("tracing: Make a snapshot feature available from userspace") Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
[ Updated commit log and comment in the code ] Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hyper-V instances support PCI pass-through which is implemented through PV
pci-hyperv driver. When a device is passed through, a new root PCI bus is
created in the guest. The bus sits on top of VMBus and has no associated
information in ACPI. acpi_pci_add_bus() in this case proceeds all the way
to acpi_evaluate_dsm(), which reports
ACPI: \: failed to evaluate _DSM (0x1001)
While acpi_pci_slot_enumerate() and acpiphp_enumerate_slots() are protected
against ACPI_HANDLE() being NULL and do nothing, acpi_evaluate_dsm() is not
and gives us the error. It seems the correct fix is to not do anything in
acpi_pci_add_bus() in such cases.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Cc: Sinan Kaya <okaya@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ext4_check_descriptors() was getting called before s_gdb_count was
initialized. So for file systems w/o the meta_bg feature, allocation
bitmaps could overlap the block group descriptors and ext4 wouldn't
notice.
For file systems with the meta_bg feature enabled, there was a
fencepost error which would cause the ext4_check_descriptors() to
incorrectly believe that the block allocation bitmap overlaps with the
block group descriptor blocks, and it would reject the mount.
As user-supplied nladdr->nl_groups is __u32, it's possible to subscribe
only to first 32 groups.
The check for correctness of .bind() userspace supplied parameter
is done by applying mask made from ngroups shift. Which broke Android
as they have 64 groups and the shift for mask resulted in an overflow.
Fixes: 61f4b23769f0 ("netlink: Don't shift with UB on nlk->ngroups") Cc: "David S. Miller" <davem@davemloft.net> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Reported-and-Tested-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Dmitry Safonov <dima@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On i386 nlk->ngroups might be 32 or 0. Which leads to UB, resulting in
hang during boot.
Check for 0 ngroups and use (unsigned long long) as a type to shift.
Fixes: 7acf9d4237c4 ("netlink: Do not subscribe to non-existent groups"). Reported-by: kernel test robot <rong.a.chen@intel.com> Signed-off-by: Dmitry Safonov <dima@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make ABI more strict about subscribing to group > ngroups.
Code doesn't check for that and it looks bogus.
(one can subscribe to non-existing group)
Still, it's possible to bind() to all possible groups with (-1)
Cc: "David S. Miller" <davem@davemloft.net> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: netdev@vger.kernel.org Signed-off-by: Dmitry Safonov <dima@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The support of force threading interrupts which are set up with both a
primary and a threaded handler wreckaged the setup of regular requested
threaded interrupts (primary handler == NULL).
The reason is that it does not check whether the primary handler is set to
the default handler which wakes the handler thread. Instead it replaces the
thread handler with the primary handler as it would do with force threaded
interrupts which have been requested via request_irq(). So both the primary
and the thread handler become the same which then triggers the warnon that
the thread handler tries to wakeup a not configured secondary thread.
Fortunately this only happens when the driver omits the IRQF_ONESHOT flag
when requesting the threaded interrupt, which is normaly caught by the
sanity checks when force irq threading is disabled.
Fix it by skipping the force threading setup when a regular threaded
interrupt is requested. As a consequence the interrupt request which lacks
the IRQ_ONESHOT flag is rejected correctly instead of silently wreckaging
it.
Fixes: 2a1d3ab8986d ("genirq: Handle force threading of irqs with primary and thread handler") Reported-by: Kurt Kanzenbach <kurt.kanzenbach@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Kurt Kanzenbach <kurt.kanzenbach@linutronix.de> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During unload process, the chip can encounter problem where a FW dump would
be captured. For this case, the full reset sequence will be skip to bring
the chip back to full operational state.
Fixes: e315cd28b9ef ("[SCSI] qla2xxx: Code changes for qla data structure refactoring") Cc: <stable@vger.kernel.org> Signed-off-by: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a minor memory leak when there is an error opening a /dev/sg device.
Fixes: cc833acbee9d ("sg: O_EXCL and other lock handling") Cc: <stable@vger.kernel.org> Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was detected by the self-test thanks to Ard's chunking patch.
I finally got around to testing this out on my ancient Via box. It
turns out that the workaround got the assembly wrong and we end up
doing count + initial cycles of the loop instead of just count.
This obviously causes corruption, either by overwriting the source
that is yet to be processed, or writing over the end of the buffer.
On CPUs that don't require the workaround only ECB is affected.
On Nano CPUs both ECB and CBC are affected.
This patch fixes it by doing the subtraction prior to the assembly.
Fixes: a76c1c23d0c3 ("crypto: padlock-aes - work around Nano CPU...") Cc: <stable@vger.kernel.org> Reported-by: Jamie Heilman <jamie@audible.transient.net> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VPID for the nested vcpu is allocated at vmx_create_vcpu whenever nested
vmx is turned on with the module parameter.
However, it's only freed if the L1 guest has executed VMXON which is not
a given.
As a result, on a system with nested==on every creation+deletion of an
L1 vcpu without running an L2 guest results in leaking one vpid. Since
the total number of vpids is limited to 64k, they can eventually get
exhausted, preventing L2 from starting.
Delay allocation of the L2 vpid until VMXON emulation, thus matching its
freeing.
Fixes: 5c614b3583e7b6dab0c86356fa36c2bcbb8322a0 Cc: stable@vger.kernel.org Signed-off-by: Roman Kagan <rkagan@virtuozzo.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It happens in the pagefault and results in double pagefault
during compacting pages when memory allocation fails.
Analysed the vmcore, the page leads to second pagefault is corrupted
with _mapcount=-256, but private=0.
It's caused by the race between migration and ballooning, and lock
missing in virtballoon_migratepage() of virtio_balloon driver.
This patch fix the bug.
Fixes: e22504296d4f64f ("virtio_balloon: introduce migration primitives to balloon pages") Cc: stable@vger.kernel.org Signed-off-by: Jiang Biao <jiang.biao2@zte.com.cn> Signed-off-by: Huang Chong <huang.chong@zte.com.cn> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: Jeremy Cline <jcline@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The squashfs fragment reading code doesn't actually verify that the
fragment is inside the fragment table. The end result _is_ verified to
be inside the image when actually reading the fragment data, but before
that is done, we may end up taking a page fault because the fragment
table itself might not even exist.
Another report from Anatoly and his endless squashfs image fuzzing.
Anatoly reports another squashfs fuzzing issue, where the decompression
parameters themselves are in a compressed block.
This causes squashfs_read_data() to be called in order to read the
decompression options before the decompression stream having been set
up, making squashfs go sideways.
'protocol' is a user-controlled value, so sanitize it after the bounds
check to avoid using it for speculative out-of-bounds access to arrays
indexed by it.
This addresses the following accesses detected with the help of smatch:
We currently check current frags memory usage only when
a new frag queue is created. This allows attackers to first
consume the memory budget (default : 4 MB) creating thousands
of frag queues, then sending tiny skbs to exceed high_thresh
limit by 2 to 3 order of magnitude.
Note that before commit 648700f76b03 ("inet: frags: use rhashtables
for reassembly units"), work queue could be starved under DOS,
getting no cpu cycles.
After commit 648700f76b03, only the per frag queue timer can eventually
remove an incomplete frag queue and its skbs.
Fixes: b13d3cbfb8e8 ("inet: frag: move eviction of queues to work queue") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jann Horn <jannh@google.com> Cc: Florian Westphal <fw@strlen.de> Cc: Peter Oskolkov <posk@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Brakmo proposal ( https://patchwork.ozlabs.org/patch/935233/
tcp: force cwnd at least 2 in tcp_cwnd_reduction) made us rethink
about our recent patch removing ~16 quick acks after ECN events.
tcp_enter_quickack_mode(sk, 1) makes sure one immediate ack is sent,
but in the case the sender cwnd was lowered to 1, we do not want
to have a delayed ack for the next packet we will receive.
Fixes: 522040ea5fdd ("tcp: do not aggressively quick ack after ECN events") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Neal Cardwell <ncardwell@google.com> Cc: Lawrence Brakmo <brakmo@fb.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As explained in commit 9f9843a751d0 ("tcp: properly handle stretch
acks in slow start"), TCP stacks have to consider how many packets
are acknowledged in one single ACK, because of GRO, but also
because of ACK compression or losses.
We plan to add SACK compression in the following patch, we
must therefore not call tcp_enter_quickack_mode()
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As for today STMMAC_ALIGN macro (which is used to align DMA stuff)
relies on L1 line length (L1_CACHE_BYTES).
This isn't correct in case of system with several cache levels
which might have L1 cache line length smaller than L2 line. This
can lead to sharing one cache line between DMA buffer and other
data, so we can lose this data while invalidate DMA buffer before
DMA transaction.
Fix that by using SMP_CACHE_BYTES instead of L1_CACHE_BYTES for
aligning.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When loading module manually, after call xenbus_switch_state to initializes
the state of the netfront device, the driver state did not change so fast
that may lead no dev created in latest kernel. This patch adds wait to make
sure xenbus knows the driver is not in closed/unknown state.
Current state:
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Cannot get device settings: No such device
Cannot get wake-on-lan settings: No such device
Cannot get message level: No such device
Cannot get link status: No such device
No data available
With the patch installed.
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
[vm]# modprobe -r xen_netfront
[vm]# modprobe xen_netfront
[vm]# ethtool eth0
Settings for eth0:
Link detected: yes
Signed-off-by: Xiao Liang <xiliang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As long the bh tasklet isn't scheduled once, no packet from the rx path
will be handled. Since the tx path also schedule the same tasklet
this situation only persits until the first packet transmission.
So fix this issue by scheduling the tasklet after link reset.
Link: https://github.com/raspberrypi/linux/issues/2617 Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet") Suggested-by: Floris Bos <bos@je-eigen-domein.nl> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we enable or disable xgbe flow-control by ethtool ,
it does't work.Because the parameter is not properly
assigned,so we need to adjust the assignment order
of the parameters.
Fixes: c1ce2f77366b ("amd-xgbe: Fix flow control setting logic") Signed-off-by: tangpengpeng <tangpengpeng@higon.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove BUG_ON() from fib_compute_spec_dst routine and check
in_dev pointer during flowi4 data structure initialization.
fib_compute_spec_dst routine can be run concurrently with device removal
where ip_ptr net_device pointer is set to NULL. This can happen
if userspace enables pkt info on UDP rx socket and the device
is removed while traffic is flowing
Fixes: 35ebf65e851c ("ipv4: Create and use fib_compute_spec_dst() helper") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These platform drivers are lacking MODULE_ALIAS so module autoloading
doesn't work. Tested on corgi and poodle with kernel 4.4.
Signed-off-by: Andrea Adami <andrea.adami@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 044e6e3d74a3: "ext4: don't update checksum of new
initialized bitmaps" the buffer valid bit will get set without
actually setting up the checksum for the allocation bitmap, since the
checksum will get calculated once we actually allocate an inode or
block.
If we are doing this, then we need to (re-)check the verified bit
after we take the block group lock. Otherwise, we could race with
another process reading and verifying the bitmap, which would then
complain about the checksum being invalid.