Hub driver will try to disable a USB3 device twice at logical disconnect,
racing with xhci_free_dev() callback from the first port disable.
This can be triggered with "udisksctl power-off --block-device <disk>"
or by writing "1" to the "remove" sysfs file for a USB3 device
in 4.17-rc4.
USB3 devices don't have a similar disabled link state as USB2 devices,
and use a U3 suspended link state instead. In this state the port
is still enabled and connected.
hub_port_connect() first disconnects the device, then later it notices
that device is still enabled (due to U3 states) it will try to disable
the port again (set to U3).
The xhci_free_dev() called during device disable is async, so checking
for existing xhci->devs[i] when setting link state to U3 the second time
was successful, even if device was being freed.
The regression was caused by, and whole thing revealed by,
Commit 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device")
which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned.
and causes a NULL pointer dereference the second time we try to set U3.
Fix this by checking xhci->devs[i]->udev exists before setting link state.
The original patch went to stable so this fix needs to be applied there as
well.
Fixes: 44a182b9d177 ("xhci: Fix use-after-free in xhci_free_virt_device") Cc: <stable@vger.kernel.org> Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch> Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a UHID_CREATE command is written to the uhid char device, a
copy_from_user() is done from a user pointer embedded in the command.
When the address limit is KERNEL_DS, e.g. as is the case during
sys_sendfile(), this can read from kernel memory. Alternatively,
information can be leaked from a setuid binary that is tricked to write
to the file descriptor. Therefore, forbid UHID_CREATE in these cases.
No other commands in uhid_char_write() are affected by this bug and
UHID_CREATE is marked as "obsolete", so apply the restriction to
UHID_CREATE only rather than to uhid_char_write() entirely.
Thanks to Dmitry Vyukov for adding uhid definitions to syzkaller and to
Jann Horn for commit 9da3f2b740544 ("x86/fault: BUG() when uaccess
helpers fault on kernel addresses"), allowing this bug to be found.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[only take the include/linux/uaccess.h portion - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many HP AMD based laptops contain an SMB0001 device like this:
Device (SMBD)
{
Name (_HID, "SMB0001") // _HID: Hardware ID
Name (_CRS, ResourceTemplate () // _CRS: Current Resource Settings
{
IO (Decode16,
0x0B20, // Range Minimum
0x0B20, // Range Maximum
0x20, // Alignment
0x20, // Length
)
IRQ (Level, ActiveLow, Shared, )
{7}
})
}
The legacy style IRQ resource here causes acpi_dev_get_irqresource() to
be called with legacy=true and this message to show in dmesg:
ACPI: IRQ 7 override to edge, high
This causes issues when later on the AMD0030 GPIO device gets enumerated:
Device (GPIO)
{
Name (_HID, "AMDI0030") // _HID: Hardware ID
Name (_CID, "AMDI0030") // _CID: Compatible ID
Name (_UID, Zero) // _UID: Unique ID
Method (_CRS, 0, NotSerialized) // _CRS: Current Resource Settings
{
Name (RBUF, ResourceTemplate ()
{
Interrupt (ResourceConsumer, Level, ActiveLow, Shared, ,, )
{
0x00000007,
}
Memory32Fixed (ReadWrite,
0xFED81500, // Address Base
0x00000400, // Address Length
)
})
Return (RBUF) /* \_SB_.GPIO._CRS.RBUF */
}
}
Now acpi_dev_get_irqresource() gets called with legacy=false, but because
of the earlier override of the trigger-type acpi_register_gsi() returns
-EBUSY (because we try to register the same interrupt with a different
trigger-type) and we end up setting IORESOURCE_DISABLED in the flags.
The setting of IORESOURCE_DISABLED causes platform_get_irq() to call
acpi_irq_get() which is not implemented on x86 and returns -EINVAL.
resulting in the following in dmesg:
amd_gpio AMDI0030:00: Failed to get gpio IRQ: -22
amd_gpio: probe of AMDI0030:00 failed with error -22
The SMB0001 is a "virtual" device in the sense that the only way the OS
interacts with it is through calling a couple of methods to do SMBus
transfers. As such it is weird that it has IO and IRQ resources at all,
because the driver for it is not expected to ever access the hardware
directly.
The Linux driver for the SMB0001 device directly binds to the acpi_device
through the acpi_bus, so we do not need to instantiate a platform_device
for this ACPI device. This commit adds the SMB0001 HID to the
forbidden_id_list, avoiding the instantiating of a platform_device for it.
Not instantiating a platform_device means we will no longer call
acpi_dev_get_irqresource() for the legacy IRQ resource fixing the probe of
the AMDI0030 device failing.
Fix this by sanitizing req.gid before calling macro GID_TO_GRU, which
uses it to index gru_base.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
After building the kernel with Clang, the following section mismatch
warning appears:
WARNING: vmlinux.o(.text+0x3bf19a6): Section mismatch in reference from
the function ssc_probe() to the function
.init.text:atmel_ssc_get_driver_data()
The function ssc_probe() references
the function __init atmel_ssc_get_driver_data().
This is often because ssc_probe lacks a __init
annotation or the annotation of atmel_ssc_get_driver_data is wrong.
Remove __init from atmel_ssc_get_driver_data to get rid of the mismatch.
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110
Raydium USB touchscreen fails to set config if LPM is enabled:
[ 2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[ 2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.030660] usb 1-8: Product: Raydium Touch System
[ 2.030661] usb 1-8: Manufacturer: Raydium Corporation
[ 7.132209] usb 1-8: can't set config #1, error -110
Same behavior can be observed on 2386:3114.
Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.
The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
idVendor 0x0572
idProduct 0x1349
I was trying to solve a double free but I introduced a more serious
NULL dereference bug. The problem is that if there is an IRQ which
triggers immediately, then we need "info->uio_dev" but it's not set yet.
This patch puts the original initialization back to how it was and just
sets info->uio_dev to NULL on the error path so it should solve both
the Oops and the double free.
Patch ad608fbcf166 changed how events were subscribed to address an issue
elsewhere. As a side effect of that change, the "add" callback was called
before the event subscription was added to the list of subscribed events,
causing the first event queued by the add callback (and possibly other
events arriving soon afterwards) to be lost.
Fix this by adding the subscription to the list before calling the "add"
callback, and clean up afterwards if that fails.
Fixes: ad608fbcf166 ("media: v4l: event: Prevent freeing event subscriptions while accessed") Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.org> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.org> Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com> Tested-by: Hans Verkuil <hans.verkuil@cisco.com> Cc: stable@vger.kernel.org (for 4.14 and up) Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
[Sakari Ailus: Backported to v4.9 stable] Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the above line there's "pinned=18446744073708158976" which is an
unsigned u64 value of -1392640, an obvious underflow.
When transaction_kthread is running cleanup_transaction(), another
fsstress is running btrfs_commit_transaction(). The
btrfs_finish_extent_commit() may get the same range as
btrfs_destroy_pinned_extent() got, which causes the pinned underflow.
Fixes: d4b450cd4b33 ("Btrfs: fix race between transaction commit and empty block group removal") CC: stable@vger.kernel.org # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Lu Fengqi <lufq.fnst@cn.fujitsu.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
gfs2_put_super calls gfs2_clear_rgrpd to destroy the gfs2_rgrpd objects
attached to the resource group glocks. That function should release the
buffers attached to the gfs2_bitmap objects (bi_bh), but the call to
gfs2_rgrp_brelse for doing that is missing.
When gfs2_releasepage later runs across these buffers which are still
referenced, it refuses to free them. This causes the pages the buffers
are attached to to remain referenced as well. With enough mount/unmount
cycles, the system will eventually run out of memory.
Fix this by adding the missing call to gfs2_rgrp_brelse in
gfs2_clear_rgrpd.
(Also fix a gfs2_rgrp_relse -> gfs2_rgrp_brelse typo in a comment.)
I got a report from Howard Chen that he saw zram and sysfs race(ie,
zram block device file is created but sysfs for it isn't yet)
when he tried to create new zram devices via hotadd knob.
v4.20 kernel fixes it by [1, 2] but it's too large size to merge
into -stable so this patch fixes the problem by registering defualt
group by Greg KH's approach[3].
This patch should be applied to every stable tree [3.16+] currently
existing from kernel.org because the problem was introduced at 2.6.37
by [4].
[1] fef912bf860e, block: genhd: add 'groups' argument to device_add_disk
[2] 98af4d4df889, zram: register default groups with device_add_disk()
[3] http://kroah.com/log/blog/2013/06/26/how-to-create-a-sysfs-file-correctly/
[4] 33863c21e69e9, Staging: zram: Replace ioctls with sysfs interface
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Hannes Reinecke <hare@suse.com> Tested-by: Howard Chen <howardsoc@google.com> Signed-off-by: Minchan Kim <minchan@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
WARNING: vmlinux.o(.text+0x4df549c): Section mismatch in reference from the function .create_device_attrs() to the function .init.text:.make_sensor_label()
The function .create_device_attrs() references
the function __init .make_sensor_label().
This is often because .create_device_attrs lacks a __init
annotation or the annotation of .make_sensor_label is wrong.
As .probe() can be called after freeing of __init memory, all __init
annotiations in the driver are bogus, and should be removed.
When IDLETIMER rule is added, sysfs file is created under
/sys/class/xt_idletimer/timers/
But some label name shouldn't be used.
".", "..", "power", "uevent", "subsystem", etc...
So that sysfs filename checking routine is needed.
Allow /0 as advertised for hash:net,port,net sets.
For "hash:net,port,net", ipset(8) says that "either subnet
is permitted to be a /0 should you wish to match port
between all destinations."
Make that statement true.
Before:
# ipset create cidrzero hash:net,port,net
# ipset add cidrzero 0.0.0.0/0,12345,0.0.0.0/0
ipset v6.34: The value of the CIDR parameter of the IP address is invalid
# ipset create cidrzero6 hash:net,port,net family inet6
# ipset add cidrzero6 ::/0,12345,::/0
ipset v6.34: The value of the CIDR parameter of the IP address is invalid
After:
# ipset create cidrzero hash:net,port,net
# ipset add cidrzero 0.0.0.0/0,12345,0.0.0.0/0
# ipset test cidrzero 192.168.205.129,12345,172.16.205.129
192.168.205.129,tcp:12345,172.16.205.129 is in set cidrzero.
# ipset create cidrzero6 hash:net,port,net family inet6
# ipset add cidrzero6 ::/0,12345,::/0
# ipset test cidrzero6 fe80::1,12345,ff00::1
fe80::1,tcp:12345,ff00::1 is in set cidrzero6.
According to Documentation/kbuild/makefiles.txt all build targets using
if_changed should use FORCE as well. Add missing FORCE to make sure
vdso targets are rebuild properly when not just immediate prerequisites
have changed but also when build command differs.
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns that if the default case is taken, ret will be
uninitialized.
./arch/arm64/include/asm/percpu.h:196:2: warning: variable 'ret' is used
uninitialized whenever switch default is taken
[-Wsometimes-uninitialized]
default:
^~~~~~~
./arch/arm64/include/asm/percpu.h:200:9: note: uninitialized use occurs
here
return ret;
^~~
./arch/arm64/include/asm/percpu.h:157:19: note: initialize the variable
'ret' to silence this warning
unsigned long ret, loop;
^
= 0
This warning appears several times while building the erofs filesystem.
While it's not strictly wrong, the BUILD_BUG will prevent this from
becoming a true problem. Initialize ret to 0 in the default case right
before the BUILD_BUG to silence all of these warnings.
Reported-by: Prasad Sodagudi <psodagud@codeaurora.org> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Dennis Zhou <dennis@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As can be seen in the context, the BIOS registers haven't changed in
the previous versions, so the assumption is they won't have changed
in this last update for this somewhat older platform either.
Cc: Peter Feuerer <peter@piie.net> Cc: Darren Hart <dvhart@infradead.org> Cc: Andy Shevchenko <andy@infradead.org> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-by: Peter Feuerer <peter@piie.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure that clocks for core SoC modules (including TZPC0..9 modules)
are enabled for suspend/resume cycle. This fixes suspend/resume
support on Exynos5422-based Odroid XU3/XU4 boards.
Fixes:
arch/um/os-Linux/skas/process.c:613:1: warning: control reaches end of
non-void function [-Wreturn-type]
longjmp() never returns but gcc still warns that the end of the function
can be reached.
Add a return code and debug aid to detect this impossible case.
Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
Creating, renaming or deleting a file may cause catalog corruption and
data loss. This bug is randomly triggered by xfstests generic/027, but
here is a faster reproducer:
truncate -s 50M fs.iso
mkfs.hfsplus fs.iso
mount fs.iso /mnt
i=100
while [ $i -le 150 ]; do
touch /mnt/$i &>/dev/null
((++i))
done
i=100
while [ $i -le 150 ]; do
mv /mnt/$i /mnt/$(perl -e "print $i x82") &>/dev/null
((++i))
done
umount /mnt
fsck.hfsplus -n fs.iso
The bug is triggered whenever hfs_brec_update_parent() needs to split the
root node. The height of the btree is not increased, which leaves the new
node orphaned and its records lost.
This bug is triggered whenever hfs_brec_update_parent() needs to split
the root node. The height of the btree is not increased, which leaves
the new node orphaned and its records lost. It is not possible for this
to happen on a valid hfs filesystem because the index nodes have fixed
length keys.
For reasons I ignore, the hfs module does have support for a number of
hfsplus features. A corrupt btree header may report variable length
keys and trigger this bug, so it's better to fix it.
fill_with_dentries() failed to propagate errors up to
reiserfs_for_each_xattr() properly. Plumb them through.
Note that reiserfs_for_each_xattr() is only used by
reiserfs_delete_xattrs() and reiserfs_chown_xattrs(). The result of
reiserfs_delete_xattrs() is discarded anyway, the only difference there is
whether a warning is printed to dmesg. The result of
reiserfs_chown_xattrs() does matter because it can block chowning of the
file to which the xattrs belong; but either way, the resulting state can
have misaligned ownership, so my patch doesn't improve things greatly.
Credit for making me look at this code goes to Al Viro, who pointed out
that the ->actor calling convention is suboptimal and should be changed.
Link: http://lkml.kernel.org/r/20180802163335.83312-1-jannh@google.com Signed-off-by: Jann Horn <jannh@google.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Jeff Mahoney <jeffm@suse.com> Cc: Eric Biggers <ebiggers@google.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
8f91869766c0 ("x86/build: Fix stack alignment for CLang")
cc-option is only used to determine the name of the stack alignment option
supported by the compiler, but not to verify that the actual parameter
<option>=N is valid in combination with the other CFLAGS.
This causes problems (as reported by the kbuild robot) with older GCC versions
which only support stack alignment on a boundary of 16 bytes or higher.
Also use (__)cc_option to add the stack alignment option to CFLAGS to
make sure only valid options are added.
d77698df39a5 ("x86/build: Specify stack alignment for clang")
intended to use the same stack alignment for clang as with gcc.
The two compilers use different options to configure the stack alignment
(gcc: -mpreferred-stack-boundary=n, clang: -mstack-alignment=n).
The above commit assumes that the clang option uses the same parameter
type as gcc, i.e. that the alignment is specified as 2^n. However clang
interprets the value of this option literally to use an alignment of n,
in consequence the stack remains misaligned.
Change the values used with -mstack-alignment to be the actual alignment
instead of a power of two.
cc-option isn't used here with the typical pattern of KBUILD_CFLAGS +=
$(call cc-option ...). The reason is that older gcc versions don't
support the -mpreferred-stack-boundary option, since cc-option doesn't
verify whether the alternative option is valid it would incorrectly
select the clang option -mstack-alignment..
undef memcpy() and friends in boot/string.c so that the functions
defined here will have the correct names, otherwise we end up
up trying to redefine __builtin_memcpy() etc.
Surprisingly, GCC allows this (and, helpfully, discards the
__builtin_ prefix from the function name when compiling it),
but clang does not.
Adding these #undef's appears to preserve what I assume was
the original intent of the code.
Signed-off-by: Michael Davidson <md@google.com> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Acked-by: H. Peter Anvin <hpa@zytor.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Bernhard.Rosenkranzer@linaro.org Cc: Greg Hackmann <ghackmann@google.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170724235155.79255-1-mka@chromium.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For gcc stack alignment is configured with -mpreferred-stack-boundary=N,
clang has the option -mstack-alignment=N for that purpose. Use the same
alignment as with gcc.
If the alignment is not specified clang assumes an alignment of
16 bytes, as required by the standard ABI. However as mentioned in d9b0cde91c60 ("x86-64, gcc: Use -mpreferred-stack-boundary=3 if
supported") the standard kernel entry on x86-64 leaves the stack
on an 8-byte boundary, as a consequence clang will keep the stack
misaligned.
cc-option is used to enable compiler options for the boot code if they
are available. The macro uses KBUILD_CFLAGS and KBUILD_CPPFLAGS for the
check, however these flags aren't used to build the boot code, in
consequence cc-option can yield wrong results. For example
-mpreferred-stack-boundary=2 is never set with a 64-bit compiler,
since the setting is only valid for 16 and 32-bit binaries. This
is also the case for 32-bit kernel builds, because the option -m32 is
added to KBUILD_CFLAGS after the assignment of REALMODE_CFLAGS.
Use __cc-option instead of cc-option for the boot mode options.
The macro receives the compiler options as parameter instead of using
KBUILD_C*FLAGS, for the boot code we pass REALMODE_CFLAGS.
Also use separate statements for the __cc-option checks instead
of performing them in the initial assignment of REALMODE_CFLAGS since
the variable is an input of the macro.
cc-option uses KBUILD_CFLAGS and KBUILD_CPPFLAGS when it determines
whether an option is supported or not. This is fine for options used to
build the kernel itself, however some components like the x86 boot code
use a different set of flags.
Add the new macro __cc-option which is a more generic version of
cc-option with additional parameters. One parameter is the compiler
with which the check should be performed, the other the compiler options
to be used instead KBUILD_C*FLAGS.
Refactor cc-option and hostcc-option to use __cc-option and move
hostcc-option to scripts/Kbuild.include.
Suggested-by: Arnd Bergmann <arnd@arndb.de> Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Michal Marek <mmarek@suse.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[nc: Fix conflicts due to lack of CC_OPTION_CFLAGS and hostcc-option
wasn't added until v4.8 so no point including it in this tree] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The constraint "rm" allows the compiler to put mix_const into memory.
When the input operand is a memory location then MUL needs an operand
size suffix, since Clang can't infer the multiplication width from the
operand.
Add and use the _ASM_MUL macro which determines the operand size and
resolves to the NUL instruction with the corresponding suffix.
This fixes the following error when building with clang:
CC arch/x86/lib/kaslr.o
/tmp/kaslr-dfe1ad.s: Assembler messages:
/tmp/kaslr-dfe1ad.s:182: Error: no instruction mnemonic suffix given and no register operands; can't size instruction
Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Cc: Grant Grundler <grundler@chromium.org> Cc: Greg Hackmann <ghackmann@google.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Davidson <md@google.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20170501224741.133938-1-mka@chromium.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
[nc: Apply to aslr.c in get_random_long as the kaslr shift didn't happen
until 4.8 in commit d899a7d146a2] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
aes_ctrby8_avx-x86_64.S uses the C preprocessor for token pasting
of character sequences that are not valid preprocessor tokens.
While this is allowed when preprocessing assembler files it exposes
an incompatibilty between the clang and gcc preprocessors where
clang does not strip leading white space from macro parameters,
leading to the CONCAT(%xmm, i) macro expansion on line 96 resulting
in a token with a space character embedded in it.
While this could be resolved by deleting the offending space character,
the assembler is perfectly capable of doing the token pasting correctly
for itself so we can just get rid of the preprocessor macros.
Signed-off-by: Michael Davidson <md@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
arm64: Disable asm-operand-width warning for clang
clang raises 'asm-operand-widths' warnings in inline assembly code when
the size of an operand is < 64 bits and the operand width is unspecified.
Most warnings are raised in macros, i.e. the datatype of the operand may
vary.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
nc: I trimmed the original commit message since I'm not a part of CrOS
and can't speak on their behalf.
To fix these warnings, it requires a fairly intrusive backport of
the sysreg conversion that Mark Rutland did in 4.9. I think
disabling the warning is smarter, similar to commit d41d0fe374d4
("turn off -Wattribute-alias") in this tree.
When using a GCC cross toolchain which is not in a compiled in
Clang search path, Clang reverts to the system assembler and
linker. This leads to assembler or linker errors, depending on
which tool is first used for a given architecture.
It seems that Clang is not searching $PATH for a matching
assembler or linker.
Make sure that Clang picks up the correct assembler or linker by
passing the cross compilers bin directory as search path.
This allows to use Clang provided by distributions with GCC
toolchains not in /usr/bin.
In order to make sure compiler flag detection for ARM works
correctly the no-integrated-as flags need to be set before
including the arch specific Makefile.
Fixes: cfe17c9bbe6a ("kbuild: move cc-option and cc-disable-warning after incl. arch Makefile") Signed-off-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[nc: Adjust context] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, GCC disables -Wunused-const-variable, but not
-Wunused-variable, so warns unused variables if they are
non-constant.
While, Clang does not warn unused variables at all regardless of
the const qualifier because -Wno-unused-const-variable is implied
by the stronger option -Wno-unused-variable.
Disable -Wunused-const-variable instead of -Wunused-variable so that
GCC and Clang work in the same way.
When compiling with `make CC=clang HOSTCC=clang`, I was seeing warnings
that clang did not recognize -fno-delete-null-pointer-checks for HOSTCC
targets. These were added in commit 61163efae020 ("kbuild: LLVMLinux:
Add Kbuild support for building kernel with Clang").
Clang does not support -fno-delete-null-pointer-checks, so adding it to
HOSTCFLAGS if HOSTCC is clang does not make sense.
It's not clear why the other warnings were disabled, and just for
HOSTCFLAGS, but I can remove them, add -Werror to HOSTCFLAGS and compile
with clang just fine.
We should avoid using the space character when passing arguments to
clang, because static code analysis check tool such as sparse may
misinterpret the arguments followed by spaces as build targets hence
cause the build to fail.
Signed-off-by: David Lin <dtwlin@google.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert reported commit ae6b289a3789 ("kbuild: Set KBUILD_CFLAGS before
incl. arch Makefile") broke cross-compilation using a cross-compiler
that supports less compiler options than the host compiler.
For example,
cc1: error: unrecognized command line option "-Wno-unused-but-set-variable"
This problem happens on architectures that setup CROSS_COMPILE in their
arch/*/Makefile.
Move the cc-option and cc-disable-warning back to the original position,
but keep the Clang target options untouched.
I was not seeing my linker flags getting added when using ld-option when
cross compiling with Clang. Upon investigation, this seems to be due to
a difference in how GCC vs Clang handle cross compilation.
GCC is configured at build time to support one backend, that is implicit
when compiling. Clang is explicit via the use of `-target <triple>` and
ships with all supported backends by default.
GNU Make feature test macros that compile then link will always fail
when cross compiling with Clang unless Clang's triple is passed along to
the compiler. For example:
$ clang -x c /dev/null -c -o temp.o
$ aarch64-linux-android/bin/ld -E temp.o
aarch64-linux-android/bin/ld:
unknown architecture of input file `temp.o' is incompatible with
aarch64 output
aarch64-linux-android/bin/ld:
warning: cannot find entry symbol _start; defaulting to 0000000000400078
$ echo $?
1
$ clang -target aarch64-linux-android- -x c /dev/null -c -o temp.o
$ aarch64-linux-android/bin/ld -E temp.o
aarch64-linux-android/bin/ld:
warning: cannot find entry symbol _start; defaulting to 00000000004002e4
$ echo $?
0
This causes conditional checks that invoke $(CC) without the target
triple, then $(LD) on the result, to always fail.
Suggested-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[nc: Fix conflicts due to lack of commit 3298b690b21cd in linux-4.4.y
Use KBUILD_CFLAGS instead of CC_OPTION_FLAGS because commit d26e94149276f that introduced that variable isn't in 4.4 either] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang may emit absolute symbol references when building in non-PIC mode,
even when using the default 'small' code model, which is already mostly
position independent to begin with, due to its use of adrp/add pairs
that have a relative range of +/- 4 GB. The remedy is to pass the -fpie
flag, which can be done safely now that the code has been updated to avoid
GOT indirections (which may be emitted due to the compiler assuming that
the PIC/PIE code may end up in a shared library that is subject to ELF
symbol preemption)
Passing -fpie when building code that needs to execute at an a priori
unknown offset is arguably an improvement in any case, and given that
the recent visibility changes allow the PIC build to pass with GCC as
well, let's add -fpie for all arm64 builds rather than only for Clang.
To prevent the compiler from emitting absolute references to the section
markers when running in PIC mode, override the visibility to 'hidden' for
all contents of asm/sections.h
Tested-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/20170818194947.19347-4-ard.biesheuvel@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
[nc: Fix conflict due to lack of commit 42b55734030c1 in linux-4.4.y] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the inline asm which exports struct offsets as ELF symbols
with proper const variables exposing the same values. This works
around an issue with Clang which does not interpret the "i" (or "I")
constraints in the same way as GCC.
clang generates plenty of these warnings in different parts of the code,
to an extent that the warnings are little more than noise. Disable the
'address-of-packed-member' warning.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang will warn about unknown warnings but will not return false
unless -Werror is set. GCC will return false if an unknown
warning is passed.
Adding -Werror make both compiler behave the same.
[arnd: it turns out we need the same patch for testing whether -ffunction-sections
works right with gcc. I've build tested extensively with this patch
applied, so let's just merge this one now.]
Signed-off-by: Mark Charlebois <charlebm@gmail.com> Signed-off-by: Behan Webster <behanw@converseincode.com> Reviewed-by: Jan-Simon Möller <dl9pf@gmx.de> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Kees Cook <keescook@chromium.org> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[nc: Adjust context due to lack of d26e94149276f] Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c3f0d0bc5b01 ("kbuild, LLVMLinux: Add -Werror to
cc-option to support clang"), cc-option and friends work nicely
for clang.
However, -Wno-unknown-warning-option makes clang happy with any
unknown warning options even if -Werror is specified.
Once -Wno-unknown-warning-option is added, any succeeding call of
cc-disable-warning is evaluated positive, then unknown warning
options are accepted. This should be dropped.
KBuild abuses the asm statement to write to a file and
clang chokes about these invalid asm statements. Hack it
even more by fooling this is actual valid asm code.
[masahiro:
Import Jeroen's work for U-Boot:
http://patchwork.ozlabs.org/patch/375026/
Tweak sed script a little to avoid garbage '#' for GCC case, like
#define NR_PAGEFLAGS 23 /* __NR_PAGEFLAGS # */ ]
This part ended up in redundant code after touched by multiple
people.
[1] Commit 3234282f33b2 ("x86, asm: Fix CFI macro invocations to
deal with shortcomings in gas") added parentheses for defined
expressions to support old gas for x86.
[2] Commit a22dcdb0032c ("x86, asm: Fix ancient-GAS workaround")
split the pattern into two to avoid parentheses for non-numeric
expressions.
[3] Commit 95a2f6f72d37 ("Partially revert patch that encloses
asm-offset.h numbers in brackets") removed parentheses from numeric
expressions as well because parentheses in MN10300 assembly have a
special meaning (pointer access).
Apparently, there is a conflict between [1] and [3]. After all,
[3] took precedence, and a long time has passed since then.
Now, merge the two patterns again because the first one is covered
by the other.
Largely redundant code is used in different places to generate C headers
from offset information extracted from assembly language output.
Consolidate the code in Makefile.lib and use this instead.
The Linux Kernel relies on GCC's acceptance of inline assembly as an
opaque object which will not have any validation performed on the content.
The current behaviour in LLVM is to perform validation of the contents by
means of parsing the input if the MC layer can handle it.
Disable clangs integrated assembler and use the GNU assembler instead.
Add cross target to CC if using clang. Also add custom gcc toolchain
path for fallback gcc tools.
Clang will fallback to using things like ld, as, and libgcc if
(respectively) one of the llvm linkers isn't available, the integrated
assembler is turned off, or an appropriately cross-compiled version of
compiler-rt isn't available. To this end, you can specify the path to
this fallback gcc toolchain with GCC_TOOLCHAIN.
Preethi reported that PMTU discovery for UDP/raw applications is not
working in the presence of VRF when the socket is not bound to a device.
The problem is that ip6_sk_update_pmtu does not consider the L3 domain
of the skb device if the socket is not bound. Update the function to
set oif to the L3 master device if relevant.
Fixes: ca254490c8df ("net: Add VRF support to IPv6 stack") Reported-by: Preethi Ramachandra <preethir@juniper.net> Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch has the fix to avoid PHY lockup with 5717/5719/5720 in change
ring and flow control paths. This patch solves the RX hang while doing
continuous ring or flow control parameters with heavy traffic from peer.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com> Acked-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
eth_type_trans() assumes initial value for skb->pkt_type
is PACKET_HOST.
This is indeed the value right after a fresh skb allocation.
However, it is possible that GRO merged a packet with a different
value (like PACKET_OTHERHOST in case macvlan is used), so
we need to make sure napi->skb will have pkt_type set back to
PACKET_HOST.
Otherwise, valid packets might be dropped by the stack because
their pkt_type is not PACKET_HOST.
napi_reuse_skb() was added in commit 96e93eab2033 ("gro: Add
internal interfaces for VLAN"), but this bug always has
been there.
Fixes: 96e93eab2033 ("gro: Add internal interfaces for VLAN") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various types of tunnels running over IPv4 can ask to set the DF
bit to do PMTU discovery. However, PMTU discovery is subject to the
threshold set by the net.ipv4.route.min_pmtu sysctl, and is also
disabled on routes with "mtu lock". In those cases, we shouldn't set
the DF bit.
This patch makes setting the DF bit conditional on the route's MTU
locking state.
This issue seems to be older than git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only first fragment has the sport/dport information,
not the following ones.
If we want consistent hash for all fragments, we need to
ignore ports even for first fragment.
This bug is visible for IPv6 traffic, if incoming fragments
do not have a flow label, since skb_get_hash() will give
different results for first fragment and following ones.
It is also visible if any routing rule wants dissection
and sport or dport.
See commit 5e5d6fed3741 ("ipv6: route: dissect flow
in input path if fib rules need it") for details.
[edumazet] rewrote the changelog completely.
Fixes: 06635a35d13d ("flow_dissect: use programable dissector in skb_flow_dissect and friends") Signed-off-by: 배석진 <soukjin.bae@samsung.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately drm_dp_get_mst_branch_device which is called from both
drm_dp_mst_handle_down_rep and drm_dp_mst_handle_up_rep seem to rely
on that mgr->mst_primary is not NULL, which seem to be wrong as it can be
cleared with simultaneous mode set, if probing fails or in other case.
mgr->lock mutex doesn't protect against that as it might just get
assigned to NULL right before, not simultaneously.
There are currently bugs 107738, 108616 bugs which crash in
drm_dp_get_mst_branch_device, caused by this issue.
v2: Refactored the code, as it was nicely noticed.
Fixed Bugzilla bug numbers(second was 108616, but not 108816)
and added links.
[changed title and added stable cc] Signed-off-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108616
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107738 Link: https://patchwork.freedesktop.org/patch/msgid/20181109090012.24438-1-stanislav.lisovskiy@intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Leaving the DRM driver enabled on reboot or kexec has the annoying
effect of leaving the display generating transactions whilst the
IOMMU has been shut down.
In turn, the IOMMU driver (which shares its interrupt line with
the VOP) starts warning either on shutdown or when entering the
secondary kernel in the kexec case (nothing is expected on that
front).
A cheap way of ensuring that things are nicely shut down is to
register a shutdown callback in the platform driver.
The page migration code employs try_to_unmap() to try and unmap the source
page. This is accomplished by using rmap_walk to find all vmas where the
page is mapped. This search stops when page mapcount is zero. For shared
PMD huge pages, the page map count is always 1 no matter the number of
mappings. Shared mappings are tracked via the reference count of the PMD
page. Therefore, try_to_unmap stops prematurely and does not completely
unmap all mappings of the source page.
This problem can result is data corruption as writes to the original
source page can happen after contents of the page are copied to the target
page. Hence, data is lost.
This problem was originally seen as DB corruption of shared global areas
after a huge page was soft offlined due to ECC memory errors. DB
developers noticed they could reproduce the issue by (hotplug) offlining
memory used to back huge pages. A simple testcase can reproduce the
problem by creating a shared PMD mapping (note that this must be at least
PUD_SIZE in size and PUD_SIZE aligned (1GB on x86)), and using
migrate_pages() to migrate process pages between nodes while continually
writing to the huge pages being migrated.
To fix, have the try_to_unmap_one routine check for huge PMD sharing by
calling huge_pmd_unshare for hugetlbfs huge pages. If it is a shared
mapping it will be 'unshared' which removes the page table entry and drops
the reference on the PMD page. After this, flush caches and TLB.
mmu notifiers are called before locking page tables, but we can not be
sure of PMD sharing until page tables are locked. Therefore, check for
the possibility of PMD sharing before locking so that notifiers can
prepare for the worst possible case.
Link: http://lkml.kernel.org/r/20180823205917.16297-2-mike.kravetz@oracle.com
[mike.kravetz@oracle.com: make _range_in_vma() a static inline] Link: http://lkml.kernel.org/r/6063f215-a5c8-2f0c-465a-2c515ddc952d@oracle.com Fixes: 39dde65c9940 ("shared page table for hugetlb page") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by: Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Jérôme Glisse <jglisse@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug has been experienced several times by the Oracle DB team. The
BUG is in remove_inode_hugepages() as follows:
/*
* If page is mapped, it was faulted in after being
* unmapped in caller. Unmap (again) now after taking
* the fault mutex. The mutex will prevent faults
* until we finish removing the page.
*
* This race can only happen in the hole punch case.
* Getting here in a truncate operation is a bug.
*/
if (unlikely(page_mapped(page))) {
BUG_ON(truncate_op);
In this case, the elevated map count is not the result of a race.
Rather it was incorrectly incremented as the result of a bug in the huge
pmd sharing code. Consider the following:
- Process A maps a hugetlbfs file of sufficient size and alignment
(PUD_SIZE) that a pmd page could be shared.
- Process B maps the same hugetlbfs file with the same size and
alignment such that a pmd page is shared.
- Process B then calls mprotect() to change protections for the mapping
with the shared pmd. As a result, the pmd is 'unshared'.
- Process B then calls mprotect() again to chage protections for the
mapping back to their original value. pmd remains unshared.
- Process B then forks and process C is created. During the fork
process, we do dup_mm -> dup_mmap -> copy_page_range to copy page
tables. Copying page tables for hugetlb mappings is done in the
routine copy_hugetlb_page_range.
In copy_hugetlb_page_range(), the destination pte is obtained by:
dst_pte = huge_pte_alloc(dst, addr, sz);
If pmd sharing is possible, the returned pointer will be to a pte in an
existing page table. In the situation above, process C could share with
either process A or process B. Since process A is first in the list,
the returned pte is a pointer to a pte in process A's page table.
However, the check for pmd sharing in copy_hugetlb_page_range is:
/* If the pagetables are shared don't copy or take references */
if (dst_pte == src_pte)
continue;
Since process C is sharing with process A instead of process B, the
above test fails. The code in copy_hugetlb_page_range which follows
assumes dst_pte points to a huge_pte_none pte. It copies the pte entry
from src_pte to dst_pte and increments this map count of the associated
page. This is how we end up with an elevated map count.
To solve, check the dst_pte entry for huge_pte_none. If !none, this
implies PMD sharing so do not copy.
Link: http://lkml.kernel.org/r/20181105212315.14125-1-mike.kravetz@oracle.com Fixes: c5c99429fa57 ("fix hugepages leak due to pagetable page sharing") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Hugh Dickins <hughd@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Prakash Sangappa <prakash.sangappa@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fs/configfs/symlink.c:67:3: warning:
'strncpy' output truncated before terminating nul copying as many
bytes from a string as its length
fs/configfs/symlink.c: In function 'configfs_get_link':
fs/configfs/symlink.c:63:13: note: length computed here
Using strncpy() is indeed less than perfect since the length of data to
be copied has already been determined with strlen(). Replace strncpy()
with memcpy() to address the warning and optimize the code a little.
fuse_request_send_notify_reply() may fail if the connection was reset for
some reason (e.g. fs was unmounted). Don't leak request reference in this
case. Besides leaking memory, this resulted in fc->num_waiting not being
decremented and hence fuse_wait_aborted() left in a hanging and unkillable
state.
Fixes: 2d45ba381a74 ("fuse: add retrieve request") Fixes: b8f95e5d13f5 ("fuse: umount should wait for all requests") Reported-and-tested-by: syzbot+6339eda9cb4ebbc4c37b@syzkaller.appspotmail.com Signed-off-by: Miklos Szeredi <mszeredi@redhat.com> Cc: <stable@vger.kernel.org> #v2.6.36 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix an issue with the 32-bit range error path in `rtc_hctosys' where no
error code is set and consequently the successful preceding call result
from `rtc_read_time' is propagated to `rtc_hctosys_ret'. This in turn
makes any subsequent call to `hctosys_show' incorrectly report in sysfs
that the system time has been set from this RTC while it has not.
Set the error to ERANGE then if we can't express the result due to an
overflow.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org> Fixes: b3a5ac42ab18 ("rtc: hctosys: Ensure system time doesn't overflow time_t") Cc: stable@vger.kernel.org # 4.17+ Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When truncating the encode buffer, the page_ptr is getting
advanced, causing the next page to be skipped while encoding.
The page is still included in the response, so the response
contains a page of bogus data.
We need to adjust the page_ptr backwards to ensure we encode
the next page into the correct place.
We saw this triggered when concurrent directory modifications caused
nfsd4_encode_direct_fattr() to return nfserr_noent, and the resulting
call to xdr_truncate_encode() corrupted the READDIR reply.
Signed-off-by: Frank Sorenson <sorenson@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Timothy Baldwin <timbaldwin@fastmail.co.uk> wrote:
> As per mount_namespaces(7) unprivileged users should not be able to look under mount points:
>
> Mounts that come as a single unit from more privileged mount are locked
> together and may not be separated in a less privileged mount namespace.
>
> However they can:
>
> 1. Create a mount namespace.
> 2. In the mount namespace open a file descriptor to the parent of a mount point.
> 3. Destroy the mount namespace.
> 4. Use the file descriptor to look under the mount point.
>
> I have reproduced this with Linux 4.16.18 and Linux 4.18-rc8.
>
> The setup:
>
> $ sudo sysctl kernel.unprivileged_userns_clone=1
> kernel.unprivileged_userns_clone = 1
> $ mkdir -p A/B/Secret
> $ sudo mount -t tmpfs hide A/B
>
>
> "Secret" is indeed hidden as expected:
>
> $ ls -lR A
> A:
> total 0
> drwxrwxrwt 2 root root 40 Feb 12 21:08 B
>
> A/B:
> total 0
>
>
> The attack revealing "Secret":
>
> $ unshare -Umr sh -c "exec unshare -m ls -lR /proc/self/fd/4/ 4<A"
> /proc/self/fd/4/:
> total 0
> drwxr-xr-x 3 root root 60 Feb 12 21:08 B
>
> /proc/self/fd/4/B:
> total 0
> drwxr-xr-x 2 root root 40 Feb 12 21:08 Secret
>
> /proc/self/fd/4/B/Secret:
> total 0
I tracked this down to put_mnt_ns running passing UMOUNT_SYNC and
disconnecting all of the mounts in a mount namespace. Fix this by
factoring drop_mounts out of drop_collected_mounts and passing
0 instead of UMOUNT_SYNC.
There are two possible behavior differences that result from this.
- No longer setting UMOUNT_SYNC will no longer set MNT_SYNC_UMOUNT on
the vfsmounts being unmounted. This effects the lazy rcu walk by
kicking the walk out of rcu mode and forcing it to be a non-lazy
walk.
- No longer disconnecting locked mounts will keep some mounts around
longer as they stay because the are locked to other mounts.
There are only two users of drop_collected mounts: audit_tree.c and
put_mnt_ns.
In audit_tree.c the mounts are private and there are no rcu lazy walks
only calls to iterate_mounts. So the changes should have no effect
except for a small timing effect as the connected mounts are disconnected.
In put_mnt_ns there may be references from process outside the mount
namespace to the mounts. So the mounts remaining connected will
be the bug fix that is needed. That rcu walks are allowed to continue
appears not to be a problem especially as the rcu walk change was about
an implementation detail not about semantics.
Cc: stable@vger.kernel.org Fixes: 5ff9d8a65ce8 ("vfs: Lock in place mounts from more privileged users") Reported-by: Timothy Baldwin <timbaldwin@fastmail.co.uk> Tested-by: Timothy Baldwin <timbaldwin@fastmail.co.uk> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Calmels from NVIDIA reported that he's able to bypass the
mount visibility security check in place in the Linux kernel by using
a combination of the unbindable property along with the private mount
propagation option to allow a unprivileged user to see a path which
was purposefully hidden by the root user.
Reproducer:
# Hide a path to all users using a tmpfs
root@castiana:~# mount -t tmpfs tmpfs /sys/devices/
root@castiana:~#
# As an unprivileged user, unshare user namespace and mount namespace
stgraber@castiana:~$ unshare -U -m -r
# Confirm the path is still not accessible
root@castiana:~# ls /sys/devices/
# Make /sys recursively unbindable and private
root@castiana:~# mount --make-runbindable /sys
root@castiana:~# mount --make-private /sys
# Recursively bind-mount the rest of /sys over to /mnnt
root@castiana:~# mount --rbind /sys/ /mnt
# Access our hidden /sys/device as an unprivileged user
root@castiana:~# ls /mnt/devices/
breakpoint cpu cstate_core cstate_pkg i915 intel_pt isa kprobe
LNXSYSTM:00 msr pci0000:00 platform pnp0 power software system
tracepoint uncore_arb uncore_cbox_0 uncore_cbox_1 uprobe virtual
Solve this by teaching copy_tree to fail if a mount turns out to be
both unbindable and locked.
Cc: stable@vger.kernel.org Fixes: 5ff9d8a65ce8 ("vfs: Lock in place mounts from more privileged users") Reported-by: Jonathan Calmels <jcalmels@nvidia.com> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was recently pointed out that the one instance of testing MNT_LOCKED
outside of the namespace_sem is in ksys_umount.
Fix that by adding a test inside of do_umount with namespace_sem and
the mount_lock held. As it helps to fail fails the existing test is
maintained with an additional comment pointing out that it may be racy
because the locks are not held.
Cc: stable@vger.kernel.org Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Fixes: 5ff9d8a65ce8 ("vfs: Lock in place mounts from more privileged users") Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently bh is set to NULL only during first iteration of for cycle,
then this pointer is not cleared after end of using.
Therefore rollback after errors can lead to extra brelse(bh) call,
decrements bh counter and later trigger an unexpected warning in __brelse()
Patch moves brelse() calls in body of cycle to exclude requirement of
brelse() call in rollback.
Fixes: 33afdcc5402d ("ext4: add a function which sets up group blocks ...") Signed-off-by: Vasily Averin <vvs@virtuozzo.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Cc: stable@kernel.org # 3.3+ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for platforms where pit_shutdown() doesn't work because of a
quirk in the PIT emulation. On these platforms setting the counter register
to zero causes the PIT to start running again, negating the shutdown.
Provide a global variable that controls whether the counter register is
zero'ed, which platform specific code can override.
We currently allow cloning a range from a file which includes the last
block of the file even if the file's size is not aligned to the block
size. This is fine and useful when the destination file has the same size,
but when it does not and the range ends somewhere in the middle of the
destination file, it leads to corruption because the bytes between the EOF
and the end of the block have undefined data (when there is support for
discard/trimming they have a value of 0x00).
The bytes in the range from 786532 (512Kb + 256Kb + 100 bytes) to 790527
(512Kb + 256Kb + 4Kb - 1) got corrupted, having now a value of 0x00 instead
of 0xb5.
This is similar to the problem we had for deduplication that got recently
fixed by commit de02b9f6bb65 ("Btrfs: fix data corruption when
deduplicating between different files").
Fix this by not allowing such operations to be performed and return the
errno -EINVAL to user space. This is what XFS is doing as well at the VFS
level. This change however now makes us return -EINVAL instead of
-EOPNOTSUPP for cases where the source range maps to an inline extent and
the destination range's end is smaller then the destination file's size,
since the detection of inline extents is done during the actual process of
dropping file extent items (at __btrfs_drop_extents()). Returning the
-EINVAL error is done early on and solely based on the input parameters
(offsets and length) and destination file's size. This makes us consistent
with XFS and anyone else supporting cloning since this case is now checked
at a higher level in the VFS and is where the -EINVAL will be returned
from starting with kernel 4.20 (the VFS changed was introduced in 4.20-rc1
by commit 07d19dc9fbe9 ("vfs: avoid problematic remapping requests into
partial EOF block"). So this change is more geared towards stable kernels,
as it's unlikely the new VFS checks get removed intentionally.
A test case for fstests follows soon, as well as an update to filter
existing tests that expect -EOPNOTSUPP to accept -EINVAL as well.
CC: <stable@vger.kernel.org> # 4.4+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alpha has had c_ispeed and c_ospeed, but still set speeds in c_cflags
using arbitrary flags. Because BOTHER is not defined, the general
Linux code doesn't allow setting arbitrary baud rates, and because
CBAUDEX == 0, we can have an array overrun of the baud_rate[] table in
drivers/tty/tty_baudrate.c if (c_cflags & CBAUD) == 037.
Resolve both problems by #defining BOTHER to 037 on Alpha.
However, userspace still needs to know if setting BOTHER is actually
safe given legacy kernels (does anyone actually care about that on
Alpha anymore?), so enable the TCGETS2/TCSETS*2 ioctls on Alpha, even
though they use the same structure. Define struct termios2 just for
compatibility; it is the exact same structure as struct termios. In a
future patchset, this will be cleaned up so the uapi headers are
usable from libc.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com> Cc: Jiri Slaby <jslaby@suse.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Eugene Syromiatnikov <esyr@redhat.com> Cc: <linux-alpha@vger.kernel.org> Cc: <linux-serial@vger.kernel.org> Cc: Johan Hovold <johan@kernel.org> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On architectures with CBAUDEX == 0 (Alpha and PowerPC), the code in tty_baudrate.c does
not do any limit checking on the tty_baudrate[] array, and in fact a
buffer overrun is possible on both architectures. Add a limit check to
prevent that situation.
This will be followed by a much bigger cleanup/simplification patch.
Signed-off-by: H. Peter Anvin (Intel) <hpa@zytor.com> Requested-by: Cc: Johan Hovold <johan@kernel.org> Cc: Jiri Slaby <jslaby@suse.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: Matt Turner <mattst88@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Kate Stewart <kstewart@linuxfoundation.org> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Eugene Syromiatnikov <esyr@redhat.com> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log