As commit 30d8177e8ac7 ("bonding: Always enable vlan tx offload")
said, we should always enable bonding's vlan tx offload, pass the
vlan packets to the slave devices with vlan tci, let them to handle
vlan implementation.
Now if encapsulation protocols like VXLAN is used, skb->encapsulation
may be set, then the packet is passed to vlan device which based on
bonding device. However in netif_skb_features(), the check of
hw_enc_features:
if (skb->encapsulation)
features &= dev->hw_enc_features;
clears NETIF_F_HW_VLAN_CTAG_TX/NETIF_F_HW_VLAN_STAG_TX. This results
in same issue in commit 30d8177e8ac7 like this:
vlan_dev_hard_start_xmit
-->dev_queue_xmit
-->validate_xmit_skb
-->netif_skb_features //NETIF_F_HW_VLAN_CTAG_TX is cleared
-->validate_xmit_vlan
-->__vlan_hwaccel_push_inside //skb->tci is cleared
...
--> bond_start_xmit
--> bond_xmit_hash //BOND_XMIT_POLICY_ENCAP34
--> __skb_flow_dissect // nhoff point to IP header
--> case htons(ETH_P_8021Q)
// skb_vlan_tag_present is false, so
vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
//vlan point to ip header wrongly
Fixes: b2a103e6d0af ("bonding: convert to ndo_fix_features") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At this point nr_frags has been incremented but the frag does not yet
have a page assigned so freeing the skb results in a crash. Reset
nr_frags before freeing the skb to prevent this.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 69e3c75f4d54 ("net: TX_RING and packet mmap") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The clang warning 'address-of-packed-member' is disabled for the general
kernel code, also disable it for the x86 boot code.
This suppresses a bunch of warnings like this when building with clang:
./arch/x86/include/asm/processor.h:535:30: warning: taking address of
packed member 'sp0' of class or structure 'x86_hw_tss' may result in an
unaligned pointer value [-Waddress-of-packed-member]
return this_cpu_read_stable(cpu_tss.x86_tss.sp0);
^~~~~~~~~~~~~~~~~~~
./arch/x86/include/asm/percpu.h:391:59: note: expanded from macro
'this_cpu_read_stable'
#define this_cpu_read_stable(var) percpu_stable_op("mov", var)
^~~
./arch/x86/include/asm/percpu.h:228:16: note: expanded from macro
'percpu_stable_op'
: "p" (&(var)));
^~~
Allowing user code to map the HPET is problematic. HPET
implementations are notoriously buggy, and there are probably many
machines on which even MMIO reads from bogus HPET addresses are
problematic.
We have a report that the Dell Precision M2800 with:
is either so slow when accessing the HPET or actually hangs in some
regard, causing soft lockups to be reported if users do unexpected
things to the HPET.
The vclock HPET code has also always been a questionable speedup.
Accessing an HPET is exceedingly slow (on the order of several
microseconds), so the added overhead in requiring a syscall to read
the HPET is a small fraction of the total code of accessing it.
To avoid future problems, let's just delete the code entirely.
In the long run, this could actually be a speedup. Waiman Long as a
patch to optimize the case where multiple CPUs contend for the HPET,
but that won't help unless all the accesses are mediated by the
kernel.
Reported-by: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Andy Lutomirski <luto@kernel.org> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Waiman Long <Waiman.Long@hpe.com> Cc: Waiman Long <waiman.long@hpe.com> Link: http://lkml.kernel.org/r/d2f90bba98db9905041cff294646d290d378f67a.1460074438.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These three related functions can't agree whether to put the
umrwr on the stack dirty and then memset it, or to initialize
it on the stack. Make them all agree.
gcc 9 now does allocation size tracking and thinks that passing the member
of a union and then accessing beyond that member's bounds is an overflow.
Instead of using the union member, use the entire union with a cast to
get to the sockaddr. gcc will now know that the memory extends the full
size of the union.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Gcc-9 complains for a memset across pointer boundaries, which happens as
the code tries to allocate a flexible array on the stack. Turns out we
cannot do this without relying on gcc-isms, so with this patch we'll embed
the fc_rport_priv structure into fcoe_rport, can use the normal
'container_of' outcast, and will only have to do a memset over one
structure.
Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_BUG is disabled, BUG_ON() will only evaluate the condition,
but will not actually stop the current thread. GCC warns about a couple
of BUG_ON() users where this actually leads to further undefined
behavior:
include/linux/ceph/osdmap.h: In function 'ceph_can_shift_osds':
include/linux/ceph/osdmap.h:54:1: warning: control reaches end of non-void function
fs/ext4/inode.c: In function 'ext4_map_blocks':
fs/ext4/inode.c:548:5: warning: 'retval' may be used uninitialized in this function
drivers/mfd/db8500-prcmu.c: In function 'prcmu_config_clkout':
drivers/mfd/db8500-prcmu.c:762:10: warning: 'div_mask' may be used uninitialized in this function
drivers/mfd/db8500-prcmu.c:769:13: warning: 'mask' may be used uninitialized in this function
drivers/mfd/db8500-prcmu.c:757:7: warning: 'bits' may be used uninitialized in this function
drivers/tty/serial/8250/8250_core.c: In function 'univ8250_release_irq':
drivers/tty/serial/8250/8250_core.c:252:18: warning: 'i' may be used uninitialized in this function
drivers/tty/serial/8250/8250_core.c:235:19: note: 'i' was declared here
There is an obvious conflict of interest here: on the one hand, someone
who disables CONFIG_BUG() will want the kernel to be as small as possible
and doesn't care about printing error messages to a console that nobody
looks at. On the other hand, running into a BUG_ON() condition means that
something has gone wrong, and we probably want to also stop doing things
that might cause data corruption.
This patch picks the second choice, and changes the NOP to BUG(), which
normally stops the execution of the current thread in some form (endless
loop or a trap). This follows the logic we applied in a4b5d580e078 ("bug:
Make BUG() always stop the machine").
For ARM multi_v7_defconfig, the size slightly increases:
So instead of saving 1.70% of the total image size, we only save 1.48%
by turning off CONFIG_BUG, but in return we can ensure that we don't run
into cases of uninitialized variable or return code uses when something
bad happens. Aside from that, we significantly reduce the number of
warnings in randconfig builds, which makes it easier to fix the warnings
about other problems.
trackpoint_detect() should be static inline while
CONFIG_MOUSE_PS2_TRACKPOINT is not set, otherwise, we build fails:
drivers/input/mouse/alps.o: In function `trackpoint_detect':
alps.c:(.text+0x8e00): multiple definition of `trackpoint_detect'
drivers/input/mouse/psmouse-base.o:psmouse-base.c:(.text+0x1b50): first defined here
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 55e3d9224b60 ("Input: psmouse - allow disabing certain protocol extensions") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Cc: Hui Wang <hui.wang@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d968d2b801d8 ("ARM: 7497/1: hw_breakpoint: allow single-byte
watchpoints on all addresses") changed the validation requirements for
hardware watchpoints on arch/arm/. Update our compat layer to implement
the same relaxation.
Cc: <stable@vger.kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The upcoming GCC 9 release extends the -Wmissing-attributes warnings
(enabled by -Wall) to C and aliases: it warns when particular function
attributes are missing in the aliases but not in their target.
In particular, it triggers for all the init/cleanup_module
aliases in the kernel (defined by the module_init/exit macros),
ending up being very noisy.
These aliases point to the __init/__exit functions of a module,
which are defined as __cold (among other attributes). However,
the aliases themselves do not have the __cold attribute.
Since the compiler behaves differently when compiling a __cold
function as well as when compiling paths leading to calls
to __cold functions, the warning is trying to point out
the possibly-forgotten attribute in the alias.
In order to keep the warning enabled, we decided to silence
this case. Ideally, we would mark the aliases directly
as __init/__exit. However, there are currently around 132 modules
in the kernel which are missing __init/__exit in their init/cleanup
functions (either because they are missing, or for other reasons,
e.g. the functions being called from somewhere else); and
a section mismatch is a hard error.
A conservative alternative was to mark the aliases as __cold only.
However, since we would like to eventually enforce __init/__exit
to be always marked, we chose to use the new __copy function
attribute (introduced by GCC 9 as well to deal with this).
With it, we copy the attributes used by the target functions
into the aliases. This way, functions that were not marked
as __init/__exit won't have their aliases marked either,
and therefore there won't be a section mismatch.
Note that the warning would go away marking either the extern
declaration, the definition, or both. However, we only mark
the definition of the alias, since we do not want callers
(which only see the declaration) to be compiled as if the function
was __cold (and therefore the paths leading to those calls
would be assumed to be unlikely).
On Motorola Mapphone devices such as Droid 4 there are five USB ports
that do not use the same layout as Gobi 1K/2K/etc devices listed in
qcserial.c. So we should use qcaux.c or option.c as noted by
Dan Williams <dan.j.williams@intel.com>.
As the Motorola USB serial ports have an interrupt endpoint as shown
with lsusb -v, we should use option.c instead of qcaux.c as pointed out
by Johan Hovold <johan@kernel.org>.
The ff/ff/ff interfaces seem to always be UARTs on Motorola devices.
For the other interfaces, class 0x0a (CDC Data) should not in general
be added as they are typically part of a multi-interface function as
noted earlier by Bjørn Mork <bjorn@mork.no>.
However, looking at the Motorola mapphone kernel code, the mdm6600 0x0a
class is only used for flashing the modem firmware, and there are no
other interfaces. So I've added that too with more details below as it
works just fine.
The ttyUSB ports on Droid 4 are:
ttyUSB0 DIAG, CQDM-capable
ttyUSB1 MUX or NMEA, no response
ttyUSB2 MUX or NMEA, no response
ttyUSB3 TCMD
ttyUSB4 AT-capable
The ttyUSB0 is detected as QCDM capable by ModemManager. I think
it's only used for debugging with ModemManager --debug for sending
custom AT commands though. ModemManager already can manage data
connection using the USB QMI ports that are already handled by the
qmi_wwan.c driver.
To enable the MUX or NMEA ports, it seems that something needs to be
done additionally to enable them, maybe via the DIAG or TCMD port.
It might be just a NVRAM setting somewhere, but I have no idea what
NVRAM settings may need changing for that.
The TCMD port seems to be a Motorola custom protocol for testing
the modem and to configure it's NVRAM and seems to work just fine
based on a quick test with a minimal tcmdrw tool I wrote.
The voice modem AT-capable port seems to provide only partial
support, and no PM support compared to the TS 27.010 based UART
wired directly to the modem.
The UARTs added with this change are the same product IDs as the
Motorola Mapphone Android Linux kernel mdm6600_id_table. I don't
have any mdm9600 based devices, so I have only tested these on
mdm6600 based droid 4.
Then for the class 0x0a (CDC Data) mode, the Motorola Mapphone Android
Linux kernel driver moto_flashqsc.c just seems to change the
port->bulk_out_size to 8K from the default. And is only used for
flashing the modem firmware it seems.
I've verified that flashing the modem with signed firmware works just
fine with the option driver after manually toggling the GPIO pins, so
I've added droid 4 modem flashing mode to the option driver. I've not
added the other devices listed in moto_flashqsc.c in case they really
need different port->bulk_out_size. Those can be added as they get
tested to work for flashing the modem.
After this patch the output of /sys/kernel/debug/usb/devices has
the following for normal 22b8:2a70 mode including the related qmi_wwan
interfaces:
This patch adds support for MF871A USB modem (aka Speed USB STICK U03)
to option driver. This modem is manufactured by ZTE corporation, and
sold by KDDI.
The syzbot fuzzer has found two (!) races in the USB character device
registration and deregistration routines. This patch fixes the races.
The first race results from the fact that usb_deregister_dev() sets
usb_minors[intf->minor] to NULL before calling device_destroy() on the
class device. This leaves a window during which another thread can
allocate the same minor number but will encounter a duplicate name
error when it tries to register its own class device. A typical error
message in the system log would look like:
The patch fixes this race by destroying the class device first.
The second race is in usb_register_dev(). When that routine runs, it
first allocates a minor number, then drops minor_rwsem, and then
creates the class device. If the device creation fails, the minor
number is deallocated and the whole routine returns an error. But
during the time while minor_rwsem was dropped, there is a window in
which the minor number is allocated and so another thread can
successfully open the device file. Typically this results in
use-after-free errors or invalid accesses when the other thread closes
its open file reference, because the kernel then tries to release
resources that were already deallocated when usb_register_dev()
failed. The patch fixes this race by keeping minor_rwsem locked
throughout the entire routine.
`dt3k_ns_to_timer()` determines the prescaler and divisor to use to
produce a desired timing period. It is influenced by a rounding mode
and can round the divisor up, down, or to the nearest value. However,
the code for rounding up currently does the same as rounding down! Fix
ir by using the `DIV_ROUND_UP()` macro to calculate the divisor when
rounding up.
Also, change the types of the `divider`, `base` and `prescale` variables
from `int` to `unsigned int` to avoid mixing signed and unsigned types
in the calculations.
Also fix a typo in a nearby comment: "improvment" => "improvement".
(`divider`, `base` and `prescale` are type `int`, `timer_base` and
`*nanosec` are type `unsigned int`. The value of `timer_base` will be
either 50 or 100.)
The main reason for the overflow is that the calculation for `base` is
completely wrong. It should be:
base = timer_base * (prescale + 1);
which matches an earlier instance of this calculation in the same
function.
Commit d66acc39c7ce ("bitops: Optimise get_order()") introduced a
compilation warning because "rx_frag_size" is an "ushort" while
PAGE_SHIFT here is 16.
The commit changed the get_order() to be a multi-line macro where
compilers insist to check all statements in the macro even when
__builtin_constant_p(rx_frag_size) will return false as "rx_frag_size"
is a module parameter.
In file included from ./arch/powerpc/include/asm/page_64.h:107,
from ./arch/powerpc/include/asm/page.h:242,
from ./arch/powerpc/include/asm/mmu.h:132,
from ./arch/powerpc/include/asm/lppaca.h:47,
from ./arch/powerpc/include/asm/paca.h:17,
from ./arch/powerpc/include/asm/current.h:13,
from ./include/linux/thread_info.h:21,
from ./arch/powerpc/include/asm/processor.h:39,
from ./include/linux/prefetch.h:15,
from drivers/net/ethernet/emulex/benet/be_main.c:14:
drivers/net/ethernet/emulex/benet/be_main.c: In function 'be_rx_cqs_create':
./include/asm-generic/getorder.h:54:9: warning: comparison is always
true due to limited range of data type [-Wtype-limits]
(((n) < (1UL << PAGE_SHIFT)) ? 0 : \
^
drivers/net/ethernet/emulex/benet/be_main.c:3138:33: note: in expansion
of macro 'get_order'
adapter->big_page_size = (1 << get_order(rx_frag_size)) * PAGE_SIZE;
^~~~~~~~~
Fix it by moving all of this multi-line macro into a proper function,
and killing __get_order() off.
[akpm@linux-foundation.org: remove __get_order() altogether]
[cai@lca.pw: v2] Link: http://lkml.kernel.org/r/1564000166-31428-1-git-send-email-cai@lca.pw Link: http://lkml.kernel.org/r/1563914986-26502-1-git-send-email-cai@lca.pw Fixes: d66acc39c7ce ("bitops: Optimise get_order()") Signed-off-by: Qian Cai <cai@lca.pw> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Cc: David S. Miller <davem@davemloft.net> Cc: Arnd Bergmann <arnd@arndb.de> Cc: David Howells <dhowells@redhat.com> Cc: Jakub Jelinek <jakub@redhat.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Bill Wendling <morbo@google.com> Cc: James Y Knight <jyknight@google.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
fs/ocfs2/xattr.c: In function ocfs2_xattr_bucket_find:
fs/ocfs2/xattr.c:3828:6: warning: variable last_hash set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Link: http://lkml.kernel.org/r/20190716132110.34836-1-yuehaibing@huawei.com Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some processors may mispredict an array bounds check and
speculatively access memory that they should not. With
a user supplied array index we like to play things safe
by masking the value with the array size before it is
used as an index.
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com> Reviewed-by: Scott Teel <scott.teel@microsemi.com> Reviewed-by: Scott Benesh <scott.benesh@microsemi.com> Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BUG: KASAN: global-out-of-bounds in ata_exec_internal_sg+0x50f/0xc70
Read of size 16 at addr ffffffff91f41f80 by task scsi_eh_1/149
...
The buggy address belongs to the variable:
cdb.48319+0x0/0x40
Much like commit 18c9a99bce2a ("libata: zpodd: small read overflow in
eject_tray()"), this fixes a cdb[] buffer length, this time in
zpodd_get_mech_type():
We read from the cdb[] buffer in ata_exec_internal_sg(). It has to be
ATAPI_CDB_LEN (16) bytes long, but this buffer is only 12 bytes.
Reported-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in> Fixes: afe759511808c ("libata: identify and init ZPODD devices") Link: https://lore.kernel.org/lkml/201907181423.E808958@keescook/ Tested-by: Jeffrin Jose T <jeffrin@rajagiritech.edu.in> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building our local version of perf with MSAN (Memory Sanitizer) and
running the perf record command, MSAN throws a use of uninitialized
value warning in "tools/perf/util/util.c:333:6".
This warning stems from the "buf" variable being passed into "write".
It originated as the variable "ev" with the type union perf_event*
defined in the "perf_event__synthesize_attr" function in
"tools/perf/util/header.c".
In the "perf_event__synthesize_attr" function they allocate space with a malloc
call using ev, then go on to only assign some of the member variables before
passing "ev" on as a parameter to the "process" function therefore "ev"
contains uninitialized memory. Changing the malloc call to zalloc to initialize
all the members of "ev" which gets rid of the warning.
To reproduce this warning, build perf by running:
make -C tools/perf CLANG=1 CC=clang EXTRA_CFLAGS="-fsanitize=memory\
-fsanitize-memory-track-origins"
(Additionally, llvm might have to be installed and clang might have to
be specified as the compiler - export CC=/usr/bin/clang)
then running:
tools/perf/perf record -o - ls / | tools/perf/perf --no-pager annotate\
-i - --stdio
Please see the cover letter for why false positive warnings may be
generated.
Signed-off-by: Numfor Mbiziwo-Tiapo <nums@google.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Ian Rogers <irogers@google.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Drayton <mbd@fb.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Song Liu <songliubraving@fb.com> Cc: Stephane Eranian <eranian@google.com> Link: http://lkml.kernel.org/r/20190724234500.253358-2-nums@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The GPCv2 is a stacked IRQ controller below the ARM GIC. It doesn't
care about the IRQ type itself, but needs to forward the type to the
parent IRQ controller, so this one can be configured correctly.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/xen/xen-pciback/conf_space_capability.c: In function pm_ctrl_write:
drivers/xen/xen-pciback/conf_space_capability.c:119:25: warning:
variable old_state set but not used [-Wunused-but-set-variable]
It is never used so can be removed.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
get_registers() may fail with -ENOMEM and in this
case we can read a garbage from the status variable tmp.
Reported-by: syzbot+3499a83b2d062ae409d4@syzkaller.appspotmail.com Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
==================================================================
BUG: KASAN: use-after-free in __lock_acquire+0x302a/0x3b50
kernel/locking/lockdep.c:3753
Read of size 8 at addr ffff8881cf591a08 by task syz-executor.1/26260
Memory state around the buggy address: ffff8881cf591900: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881cf591980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
> ffff8881cf591a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881cf591a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881cf591b00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
In order to avoid opening a disconnected device, we need to check exist
again after acquiring the existance lock, and bail out if necessary.
The ioctl handler uses the intfdata of a second interface,
which may not be present in a broken or malicious device, hence
the intfdata needs to be checked for NULL.
In snd_hda_parse_generic_codec(), 'spec' is allocated through kzalloc().
Then, the pin widgets in 'codec' are parsed. However, if the parsing
process fails, 'spec' is not deallocated, leading to a memory leak.
To fix the above issue, free 'spec' before returning the error.
This patch is sent to report an use after free in mem_cgroup_iter()
after merging commit be2657752e9e ("mm: memcg: fix use after free in
mem_cgroup_iter()").
I work with android kernel tree (4.9 & 4.14), and commit be2657752e9e
("mm: memcg: fix use after free in mem_cgroup_iter()") has been merged
to the trees. However, I can still observe use after free issues
addressed in the commit be2657752e9e. (on low-end devices, a few times
this month)
In the reclaim path, try_to_free_pages() does not setup
sc.target_mem_cgroup and sc is passed to do_try_to_free_pages(), ...,
shrink_node().
In mem_cgroup_iter(), root is set to root_mem_cgroup because
sc->target_mem_cgroup is NULL. It is possible to assign a memcg to
root_mem_cgroup.nodeinfo.iter in mem_cgroup_iter().
My device uses memcg non-hierarchical mode. When we release a memcg:
invalidate_reclaim_iterators() reaches only dead_memcg and its parents.
If non-hierarchical mode is used, invalidate_reclaim_iterators() never
reaches root_mem_cgroup.
It looks like there is a possibility of a double-free vulnerability on an
error path of the f_midi_set_alt function in the f_midi driver. If the
path is feasible then free_ep_req gets called twice:
req->complete = f_midi_complete;
err = usb_ep_queue(midi->out_ep, req, GFP_ATOMIC);
=> ...
usb_gadget_giveback_request
=>
f_midi_complete (CALLBACK)
(inside f_midi_complete, for various cases of status)
free_ep_req(ep, req); // first kfree
if (err) {
ERROR(midi, "%s: couldn't enqueue request: %d\n",
midi->out_ep->name, err);
free_ep_req(midi->out_ep, req); // second kfree
return err;
}
The double-free possibility was introduced with commit ad0d1a058eac
("usb: gadget: f_midi: fix leak on failed to enqueue out requests").
Found by MOXCAFE tool.
Signed-off-by: Tuba Yavuz <tuba@ece.ufl.edu> Fixes: ad0d1a058eac ("usb: gadget: f_midi: fix leak on failed to enqueue out requests") Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: stable <stable@vger.kernel.org> Cc: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This ensures that the midi function will only work if the proper number of
IN and OUT requrests are allocated. Otherwise the function will work with less
requests then what the user wants.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
From: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although SAS3 & SAS3.5 IT HBA controllers support 64-bit DMA addressing, as
per hardware design, if DMA-able range contains all 64-bits
set (0xFFFFFFFF-FFFFFFFF) then it results in a firmware fault.
E.g. SGE's start address is 0xFFFFFFFF-FFFF000 and data length is 0x1000
bytes. when HBA tries to DMA the data at 0xFFFFFFFF-FFFFFFFF location then
HBA will fault the firmware.
Driver will set 63-bit DMA mask to ensure the above address will not be
used.
Cc: <stable@vger.kernel.org> # 5.1.20+ Signed-off-by: Suganath Prabu <suganath-prabu.subramani@broadcom.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 63d7ef36103d ("mwifiex: Don't abort on small, spec-compliant
vendor IEs") adjusted the ieee_types_vendor_header struct, which
inadvertently messed up the offsets used in
mwifiex_is_wpa_oui_present(). Add that offset back in, mirroring
mwifiex_is_rsn_oui_present().
As it stands, commit 63d7ef36103d breaks compatibility with WPA (not
WPA2) 802.11n networks, since we hit the "info: Disable 11n if AES is
not supported by AP" case in mwifiex_is_network_compatible().
Fixes: 63d7ef36103d ("mwifiex: Don't abort on small, spec-compliant vendor IEs") Cc: <stable@vger.kernel.org> Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We had a report of a server which did not do a DFS referral
because the session setup Capabilities field was set to 0
(unlike negotiate protocol where we set CAP_DFS). Better to
send it session setup in the capabilities as well (this also
more closely matches Windows client behavior).
Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-off-by: Ronnie Sahlberg <lsahlber@redhat.com> Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we skip SMB2_TREE_CONNECT command when checking during
reconnect because Tree Connect happens when establishing
an SMB session. For SMB 3.0 protocol version the code also calls
validate negotiate which results in SMB2_IOCL command being sent
over the wire. This may deadlock on trying to acquire a mutex when
checking for reconnect. Fix this by skipping SMB2_IOCL command
when doing the reconnect check.
Signed-off-by: Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by: Steve French <stfrench@microsoft.com> Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com> CC: Stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a very similar spirit to commit c470bdc1aaf3 ("mac80211: don't WARN
on bad WMM parameters from buggy APs"), an AP may not transmit a
fully-formed WMM IE. For example, it may miss or repeat an Access
Category. The above loop won't catch that and will instead leave one of
the four ACs zeroed out. This triggers the following warning in
drv_conf_tx()
wlan0: invalid CW_min/CW_max: 0/0
and it may leave one of the hardware queues unconfigured. If we detect
such a case, let's just print a warning and fall back to the defaults.
Tested with a hacked version of hostapd, intentionally corrupting the
IEs in hostapd_eid_wmm().
In iso_packets_buffer_init(), 'b->packets' is allocated through
kmalloc_array(). Then, the aligned packet size is checked. If it is
larger than PAGE_SIZE, -EINVAL will be returned to indicate the error.
However, the allocated 'b->packets' is not deallocated on this path,
leading to a memory leak.
To fix the above issue, free 'b->packets' before returning the error code.
The code to detect if in4 is present is wrong; if in4 is not present,
the in4_input sysfs attribute is still present.
In detail:
- Ihen RTD3_MD=11 (VSEN3 present), everything is as expected (no bug).
- If we have RTD3_MD!=11 (no VSEN3), we unexpectedly have a in4_input
file under /sys and the "sensors" command displays in4_input.
But as expected, we have no in4_min, in4_max, in4_alarm, in4_beep.
Fix is_visible function to detect and report in4_input visibility
as expected.
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com> Reported-by: syzbot+513e4d0985298538bf9b@syzkaller.appspotmail.com Fixes: 0a25e1f4f185 ("can: peak_usb: add support for PEAK new CANFD USB adapters") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uninitialized Kernel memory can leak to USB devices.
Fix by using kzalloc() instead of kmalloc() on the affected buffers.
Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com> Reported-by: syzbot+d6a5a1a3657b596ef132@syzkaller.appspotmail.com Fixes: f14e22435a27 ("net: can: peak_usb: Do not do dma on the stack") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some hardware PMU drivers will override perf_event.cpu inside their
event_init callback. This causes a lockdep splat when initialized through
the kernel API:
WARNING: CPU: 0 PID: 250 at kernel/events/core.c:2917 ctx_sched_out+0x78/0x208
pc : ctx_sched_out+0x78/0x208
Call trace:
ctx_sched_out+0x78/0x208
__perf_install_in_context+0x160/0x248
remote_function+0x58/0x68
generic_exec_single+0x100/0x180
smp_call_function_single+0x174/0x1b8
perf_install_in_context+0x178/0x188
perf_event_create_kernel_counter+0x118/0x160
Fix this by calling perf_install_in_context with event->cpu, just like
perf_event_open
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Frank Li <Frank.li@nxp.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Will Deacon <will@kernel.org> Link: https://lkml.kernel.org/r/c4ebe0503623066896d7046def4d6b1e06e0eb2e.1563972056.git.leonard.crestez@nxp.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This is tripped as a result of irqs being disabled during the call to
dma_free_coherent() by ibmvfc_free_event_pool(). At this point in the code path
we have quiesced the adapter and its overly paranoid anyways to be holding the
host lock.
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While loading fw crashdump in function fw_crash_buffer_show(), left bytes
in one dma chunk was not checked, if copying size over it, overflow access
will cause kernel panic.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Acked-by: Sumit Saxena <sumit.saxena@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building a multiplatform kernel that includes armv4 support,
the default target CPU does not support the blx instruction,
which leads to a build failure:
arch/arm/mach-davinci/sleep.S: Assembler messages:
arch/arm/mach-davinci/sleep.S:56: Error: selected processor does not support `blx ip' in ARM mode
Add a .arch statement in the sources to make this file build.
When perf_add_probe_events() we call cleanup_perf_probe_events() for the
pev pointer it receives, then, as part of handling this failure the main
'perf probe' goes on and calls cleanup_params() and that will again call
cleanup_perf_probe_events()for the same pointer, so just set nevents to
zero when handling the failure of perf_add_probe_events() to avoid the
double free.
Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lkml.kernel.org/n/tip-x8qgma4g813z96dvtw9w219q@git.kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Draining makes little sense in the situation of hardware overrun, as the
hardware will have consumed all its available samples. Additionally,
draining whilst the stream is paused would presumably get stuck as no
data is being consumed on the DSP side.
Currently, whilst in SNDRV_PCM_STATE_OPEN it is possible to call
snd_compr_stop, snd_compr_drain and snd_compr_partial_drain, which
allow a transition to SNDRV_PCM_STATE_SETUP. The stream should
only be able to move to the setup state once it has received a
SNDRV_COMPRESS_SET_PARAMS ioctl. Fix this issue by not allowing
those ioctls whilst in the open state.
A previous fix to the stop handling on compressed capture streams causes
some knock on issues. The previous fix updated snd_compr_drain_notify to
set the state back to PREPARED for capture streams. This causes some
issues however as the handling for snd_compr_poll differs between the
two states and some user-space applications were relying on the poll
failing after the stream had been stopped.
To correct this regression whilst still fixing the original problem the
patch was addressing, update the capture handling to skip the PREPARED
state rather than skipping the SETUP state as it has done until now.
If the device driver were to send out a full queue's worth of SBALs,
current code would end up discovering the last of those SBALs as PRIMED
and erroneously skip the SIGA-w. This immediately stalls the queue.
Add a check to not attempt fast-requeue in this case. While at it also
make sure that the state of the previous SBAL was successfully extracted
before inspecting it.
ieee80211_set_wmm_default() normally sets up the initial CW min/max for
each queue, except that it skips doing this if the driver doesn't
support ->conf_tx. We still end up calling drv_conf_tx() in some cases
(e.g., ieee80211_reconfig()), which also still won't do anything
useful...except it complains here about the invalid CW parameters.
Let's just skip the WARN if we weren't going to do anything useful with
the parameters.
iscsi_ibft can use ACPI to find the iBFT entry during bootup,
currently, ISCSI_IBFT depends on ISCSI_IBFT_FIND which is
a X86 legacy way to find the iBFT by searching through the
low memory. This patch changes the dependency so that other
arch like ARM64 can use ISCSI_IBFT as long as the arch supports
ACPI.
ibft_init() needs to use the global variable ibft_addr declared
in iscsi_ibft_find.c. A #ifndef CONFIG_ISCSI_IBFT_FIND is needed
to declare the variable if CONFIG_ISCSI_IBFT_FIND is not selected.
Moving ibft_addr into the iscsi_ibft.c does not work because if
ISCSI_IBFT is selected as a module, the arch/x86/kernel/setup.c won't
be able to find the variable at compile time.
Signed-off-by: Thomas Tai <thomas.tai@oracle.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Thomas and Juliana report a deadlock when running:
(rmmod nf_conntrack_netlink/xfrm_user)
conntrack -e NEW -E &
modprobe -v xfrm_user
They provided following analysis:
conntrack -e NEW -E
netlink_bind()
netlink_lock_table() -> increases "nl_table_users"
nfnetlink_bind()
# does not unlock the table as it's locked by netlink_bind()
__request_module()
call_usermodehelper_exec()
This triggers "modprobe nf_conntrack_netlink" from kernel, netlink_bind()
won't return until modprobe process is done.
"modprobe xfrm_user":
xfrm_user_init()
register_pernet_subsys()
-> grab pernet_ops_rwsem
..
netlink_table_grab()
calls schedule() as "nl_table_users" is non-zero
so modprobe is blocked because netlink_bind() increased
nl_table_users while also holding pernet_ops_rwsem.
"modprobe nf_conntrack_netlink" runs and inits nf_conntrack_netlink:
ctnetlink_init()
register_pernet_subsys()
-> blocks on "pernet_ops_rwsem" thanks to xfrm_user module
both modprobe processes wait on one another -- neither can make
progress.
Switch netlink_bind() to "nowait" modprobe -- this releases the netlink
table lock, which then allows both modprobe instances to complete.
When closing the CAN device while tx skbs are inflight, echo skb could
be released twice. By calling close_candev() before unlinking all
pending tx urbs, then the internal echo_skb[] array is fully and
correctly cleared before the USB write callback and, therefore,
can_get_echo_skb() are called, for each aborted URB.
BUG: KASAN: use-after-free in usb_free_coherent+0x79/0x80
drivers/usb/core/usb.c:928
Read of size 8 at addr ffff8881b18599c8 by task syz-executor.4/16007
Memory state around the buggy address: ffff8881b1859880: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881b1859900: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
> ffff8881b1859980: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
^ ffff8881b1859a00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881b1859a80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
A quick look at the yurex_delete() shows that we drop the reference
to the usb_device before releasing any buffers associated with the
device. Delay the reference drop until we have finished the cleanup.
Threads synthesized from /proc have comms with a start time of zero, and
not marked as "exec". Currently, there can be 2 such comms. The first is
created by processing a synthesized fork event and is set to the
parent's comm string, and the second by processing a synthesized comm
event set to the thread's current comm string.
In the absence of an "exec" comm, thread__exec_comm() picks the last
(oldest) comm, which, in the case above, is the parent's comm string.
For a main thread, that is very probably wrong. Use the second-to-last
in that case.
This affects only db-export because it is the only user of
thread__exec_comm().
Example:
$ sudo perf record -a -o pt-a-sleep-1 -e intel_pt//u -- sleep 1
$ sudo chown ahunter pt-a-sleep-1
On x86-32 with PTI enabled, parts of the kernel page-tables are not shared
between processes. This can cause mappings in the vmalloc/ioremap area to
persist in some page-tables after the region is unmapped and released.
When the region is re-used the processes with the old mappings do not fault
in the new mappings but still access the old ones.
This causes undefined behavior, in reality often data corruption, kernel
oopses and panics and even spontaneous reboots.
Fix this problem by activly syncing unmaps in the vmalloc/ioremap area to
all page-tables in the system before the regions can be re-used.
References: https://bugzilla.suse.com/show_bug.cgi?id=1118689 Fixes: 5d72b4fba40ef ('x86, mm: support huge I/O mapping capability I/F') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lkml.kernel.org/r/20190719184652.11391-4-joro@8bytes.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With huge-page ioremap areas the unmappings also need to be synced between
all page-tables. Otherwise it can cause data corruption when a region is
unmapped and later re-used.
Make the vmalloc_sync_one() function ready to sync unmappings and make sure
vmalloc_sync_all() iterates over all page-tables even when an unmapped PMD
is found.
Fixes: 5d72b4fba40ef ('x86, mm: support huge I/O mapping capability I/F') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lkml.kernel.org/r/20190719184652.11391-3-joro@8bytes.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not require a struct page for the mapped memory location because it
might not exist. This can happen when an ioremapped region is mapped with
2MB pages.
Fixes: 5d72b4fba40ef ('x86, mm: support huge I/O mapping capability I/F') Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lkml.kernel.org/r/20190719184652.11391-2-joro@8bytes.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sound_insert_unit(), the controlling structure 's' is allocated through
kmalloc(). Then it is added to the sound driver list by invoking
__sound_insert_unit(). Later on, if __register_chrdev() fails, 's' is
removed from the list through __sound_remove_unit(). If 'index' is not less
than 0, -EBUSY is returned to indicate the error. However, 's' is not
deallocated on this execution path, leading to a memory leak bug.
To fix the above issue, free 's' before -EBUSY is returned.
We have to drop the mutex before we close() upon disconnect()
as close() needs the lock. This is safe to do by dropping the
mutex as intfdata is already set to NULL, so open() will fail.
Fixes: 03f36e885fc26 ("USB: open disconnect race in iowarrior") Reported-by: syzbot+a64a382964bf6c71a9c0@syzkaller.appspotmail.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20190808092728.23417-1-oneukum@suse.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On all current Atom processors, instructions that use a segment register
value (e.g. a load or store) will not speculatively execute before the
last writer of that segment retires. Thus they will not use a
speculatively written segment value.
That means on ATOMs there is no speculation through SWAPGS, so the SWAPGS
entry paths can be excluded from the extra LFENCE if PTI is disabled.
Create a separate bug flag for the through SWAPGS speculation and mark all
out-of-order ATOMs and AMD/HYGON CPUs as not affected. The in-order ATOMs
are excluded from the whole mitigation mess anyway.
Reported-by: Andrew Cooper <andrew.cooper3@citrix.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Tyler Hicks <tyhicks@canonical.com> Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
[bwh: Backported to 4.4:
- There's no whitelist entry (or any support) for Hygon CPUs
- Adjust context, indentation] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Somehow the swapgs mitigation entry code patch ended up with a JMPQ
instruction instead of JMP, where only the short jump is needed. Some
assembler versions apparently fail to optimize JMPQ into a two-byte JMP
when possible, instead always using a 7-byte JMP with relocation. For
some reason that makes the entry code explode with a #GP during boot.
Change it back to "JMP" as originally intended.
Fixes: 18ec54fdd6d1 ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations") Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bwh: Backported to 4.4: adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous commit added macro calls in the entry code which mitigate the
Spectre v1 swapgs issue if the X86_FEATURE_FENCE_SWAPGS_* features are
enabled. Enable those features where applicable.
The mitigations may be disabled with "nospectre_v1" or "mitigations=off".
There are different features which can affect the risk of attack:
- When FSGSBASE is enabled, unprivileged users are able to place any
value in GS, using the wrgsbase instruction. This means they can
write a GS value which points to any value in kernel space, which can
be useful with the following gadget in an interrupt/exception/NMI
handler:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg1
// dependent load or store based on the value of %reg
// for example: mov %(reg1), %reg2
If an interrupt is coming from user space, and the entry code
speculatively skips the swapgs (due to user branch mistraining), it
may speculatively execute the GS-based load and a subsequent dependent
load or store, exposing the kernel data to an L1 side channel leak.
Note that, on Intel, a similar attack exists in the above gadget when
coming from kernel space, if the swapgs gets speculatively executed to
switch back to the user GS. On AMD, this variant isn't possible
because swapgs is serializing with respect to future GS-based
accesses.
NOTE: The FSGSBASE patch set hasn't been merged yet, so the above case
doesn't exist quite yet.
- When FSGSBASE is disabled, the issue is mitigated somewhat because
unprivileged users must use prctl(ARCH_SET_GS) to set GS, which
restricts GS values to user space addresses only. That means the
gadget would need an additional step, since the target kernel address
needs to be read from user space first. Something like:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg1
mov (%reg1), %reg2
// dependent load or store based on the value of %reg2
// for example: mov %(reg2), %reg3
It's difficult to audit for this gadget in all the handlers, so while
there are no known instances of it, it's entirely possible that it
exists somewhere (or could be introduced in the future). Without
tooling to analyze all such code paths, consider it vulnerable.
Effects of SMAP on the !FSGSBASE case:
- If SMAP is enabled, and the CPU reports RDCL_NO (i.e., not
susceptible to Meltdown), the kernel is prevented from speculatively
reading user space memory, even L1 cached values. This effectively
disables the !FSGSBASE attack vector.
- If SMAP is enabled, but the CPU *is* susceptible to Meltdown, SMAP
still prevents the kernel from speculatively reading user space
memory. But it does *not* prevent the kernel from reading the
user value from L1, if it has already been cached. This is probably
only a small hurdle for an attacker to overcome.
Thanks to Dave Hansen for contributing the speculative_smap() function.
Thanks to Andrew Cooper for providing the inside scoop on whether swapgs
is serializing on AMD.
[ tglx: Fixed the USER fence decision and polished the comment as suggested
by Dave Hansen ]
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Dave Hansen <dave.hansen@intel.com>
[bwh: Backported to 4.4:
- Check for X86_FEATURE_KAISER instead of X86_FEATURE_PTI
- mitigations= parameter is x86-only here
- Don't use __ro_after_init
- Adjust filename, context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Spectre v1 isn't only about array bounds checks. It can affect any
conditional checks. The kernel entry code interrupt, exception, and NMI
handlers all have conditional swapgs checks. Those may be problematic in
the context of Spectre v1, as kernel code can speculatively run with a user
GS.
For example:
if (coming from user space)
swapgs
mov %gs:<percpu_offset>, %reg
mov (%reg), %reg1
When coming from user space, the CPU can speculatively skip the swapgs, and
then do a speculative percpu load using the user GS value. So the user can
speculatively force a read of any kernel value. If a gadget exists which
uses the percpu value as an address in another load/store, then the
contents of the kernel value may become visible via an L1 side channel
attack.
A similar attack exists when coming from kernel space. The CPU can
speculatively do the swapgs, causing the user GS to get used for the rest
of the speculative window.
The mitigation is similar to a traditional Spectre v1 mitigation, except:
a) index masking isn't possible; because the index (percpu offset)
isn't user-controlled; and
b) an lfence is needed in both the "from user" swapgs path and the
"from kernel" non-swapgs path (because of the two attacks described
above).
The user entry swapgs paths already have SWITCH_TO_KERNEL_CR3, which has a
CR3 write when PTI is enabled. Since CR3 writes are serializing, the
lfences can be skipped in those cases.
On the other hand, the kernel entry swapgs paths don't depend on PTI.
To avoid unnecessary lfences for the user entry case, create two separate
features for alternative patching:
Use these features in entry code to patch in lfences where needed.
The features aren't enabled yet, so there's no functional change.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Dave Hansen <dave.hansen@intel.com>
[bwh: Backported to 4.4:
- Assign the CPU feature bits from word 7
- Add FENCE_SWAPGS_KERNEL_ENTRY to NMI entry, since it does not
use paranoid_entry
- Include <asm/cpufeatures.h> in calling.h
- Adjust context] Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... can be reproduced by running the GS testcase of the ldt_gdt test unit in
the x86 selftests.
do_int80_syscall_32() will call enter_form_user_mode() to convert context
tracking state from user state to kernel state. The load_gs_index() call
can fail with user gsbase, gsbase will be fixed up and proceed if this
happen.
However, enter_from_user_mode() will be called again in the fixed up path
though it is context tracking kernel state currently.
This patch fixes it by just fixing up gsbase and telling lockdep that IRQs
are off once load_gs_index() failed with user gsbase.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/1475197266-3440-1-git-send-email-wanpeng.li@hotmail.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6935224da248 ("spi: bcm2835: enable support of 3-wire mode")
added 3-wire support to the BCM2835 SPI driver by setting the REN bit
(Read Enable) in the CS register when receiving data. The REN bit puts
the transmitter in high-impedance state. The driver recognizes that
data is to be received by checking whether the rx_buf of a transfer is
non-NULL.
Commit 3ecd37edaa2a ("spi: bcm2835: enable dma modes for transfers
meeting certain conditions") subsequently broke 3-wire support because
it set the SPI_MASTER_MUST_RX flag which causes spi_map_msg() to replace
rx_buf with a dummy buffer if it is NULL. As a result, rx_buf is
*always* non-NULL if DMA is enabled.
Reinstate 3-wire support by not only checking whether rx_buf is non-NULL,
but also checking that it is not the dummy buffer.
Fixes: 3ecd37edaa2a ("spi: bcm2835: enable dma modes for transfers meeting certain conditions") Reported-by: Nuno Sá <nuno.sa@analog.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v4.2+ Cc: Martin Sperl <kernel@martin.sperl.org> Acked-by: Stefan Wahren <wahrenst@gmx.net> Link: https://lore.kernel.org/r/328318841455e505370ef8ecad97b646c033dc8a.1562148527.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We find the memory use-after-free issue in __blk_drain_queue()
on the kernel 4.14. After read the latest kernel 4.18-rc6 we
think it has the same problem.
Memory is allocated for q->fq in the blk_init_allocated_queue().
If the elevator init function called with error return, it will
run into the fail case to free the q->fq.
Then the __blk_drain_queue() uses the same memory after the free
of the q->fq, it will lead to the unpredictable event.
The patch is to set q->fq as NULL in the fail case of
blk_init_allocated_queue().
Fixes: commit 7c94e1c157a2 ("block: introduce blk_flush_queue to drive flush machinery") Cc: <stable@vger.kernel.org> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com> Signed-off-by: xiao jin <jin.xiao@intel.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
[groeck: backport to v4.4.y/v4.9.y (context change)] Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Alessio Balsini <balsini@android.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for handling the PPPOEIOCSFWD ioctl in compat mode was added in
linux-2.5.69 along with hundreds of other commands, but was always broken
sincen only the structure is compatible, but the command number is not,
due to the size being sizeof(size_t), or at first sizeof(sizeof((struct
sockaddr_pppox)), which is different on 64-bit architectures.
Guillaume Nault adds:
And the implementation was broken until 2016 (see 29e73269aa4d ("pppoe:
fix reference counting in PPPoE proxy")), and nobody ever noticed. I
should probably have removed this ioctl entirely instead of fixing it.
Clearly, it has never been used.
Fix it by adding a compat_ioctl handler for all pppoe variants that
translates the command number and then calls the regular ioctl function.
All other ioctl commands handled by pppoe are compatible between 32-bit
and 64-bit, and require compat_ptr() conversion.
This should apply to all stable kernels.
Acked-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3968d38917eb ("bnx2x: Fix Multi-Cos.") which enabled multi-cos
feature after prolonged time in driver added some regression causing
numerous issues (sudden reboots, tx timeout etc.) reported by customers.
We plan to backout this commit and submit proper fix once we have root
cause of issues reported with this feature enabled.
Fixes: 3968d38917eb ("bnx2x: Fix Multi-Cos.") Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Manish Chopra <manishc@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When lag is active, which is controlled by the bonded mlx5e netdev, mlx5
interface unregestering must happen in the reverse order where rdma is
unregistered (unloaded) first, to guarantee all references to the lag
context in hardware is removed, then remove mlx5e netdev interface which
will cleanup the lag context from hardware.
Without this fix during destroy of LAG interface, we observed following
errors:
* mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0xe4ac33)
* mlx5_cmd_check:752:(pid 12556): DESTROY_LAG(0x843) op_mod(0x0) failed,
status bad parameter(0x3), syndrome (0xa5aee8).
Fixes: a31208b1e11d ("net/mlx5_core: New init and exit flow for mlx5_core") Reviewed-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Mark Zhang <markz@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2753ca5d9009 ("tipc: fix uninit-value in tipc_nl_compat_doit")
broke older tipc tools that use compat interface (e.g. tipc-config from
tipcutils package):
% tipc-config -p
operation not supported
The commit started to reject TIPC netlink compat messages that do not
have attributes. It is too restrictive because some of such messages are
valid (they don't need any arguments):
Commit aca51397d014 ("netns: Fix arbitrary net_device-s corruptions
on net_ns stop.") introduced a possibility to hit a BUG in case device
is returning back to init_net and two following conditions are met:
1) dev->ifindex value is used in a name of another "dev%d"
device in init_net.
2) dev->name is used by another device in init_net.
Under real life circumstances this is hard to get. Therefore this has
been present happily for over 10 years. To reproduce:
$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 86:89:3f:86:61:29 brd ff:ff:ff:ff:ff:ff
3: enp0s2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 52:54:00:12:34:56 brd ff:ff:ff:ff:ff:ff
$ ip netns add ns1
$ ip -n ns1 link add dummy1ns1 type dummy
$ ip -n ns1 link add dummy2ns1 type dummy
$ ip link set enp0s2 netns ns1
$ ip -n ns1 link set enp0s2 name dummy0
[ 100.858894] virtio_net virtio0 dummy0: renamed from enp0s2
$ ip link add dev4 type dummy
$ ip -n ns1 a
1: lo: <LOOPBACK> mtu 65536 qdisc noop state DOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: dummy1ns1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 16:63:4c:38:3e:ff brd ff:ff:ff:ff:ff:ff
3: dummy2ns1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether aa:9e:86:dd:6b:5d brd ff:ff:ff:ff:ff:ff
4: dummy0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 52:54:00:12:34:56 brd ff:ff:ff:ff:ff:ff
$ ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: dummy0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 86:89:3f:86:61:29 brd ff:ff:ff:ff:ff:ff
4: dev4: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether 5a:e1:4a:b6:ec:f8 brd ff:ff:ff:ff:ff:ff
$ ip netns del ns1
[ 158.717795] default_device_exit: failed to move dummy0 to init_net: -17
[ 158.719316] ------------[ cut here ]------------
[ 158.720591] kernel BUG at net/core/dev.c:9824!
[ 158.722260] invalid opcode: 0000 [#1] SMP KASAN PTI
[ 158.723728] CPU: 0 PID: 56 Comm: kworker/u2:1 Not tainted 5.3.0-rc1+ #18
[ 158.725422] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-2.fc30 04/01/2014
[ 158.727508] Workqueue: netns cleanup_net
[ 158.728915] RIP: 0010:default_device_exit.cold+0x1d/0x1f
[ 158.730683] Code: 84 e8 18 c9 3e fe 0f 0b e9 70 90 ff ff e8 36 e4 52 fe 89 d9 4c 89 e2 48 c7 c6 80 d6 25 84 48 c7 c7 20 c0 25 84 e8 f4 c8 3e
[ 158.736854] RSP: 0018:ffff8880347e7b90 EFLAGS: 00010282
[ 158.738752] RAX: 000000000000003b RBX: 00000000ffffffef RCX: 0000000000000000
[ 158.741369] RDX: 0000000000000000 RSI: ffffffff8128013d RDI: ffffed10068fcf64
[ 158.743418] RBP: ffff888033550170 R08: 000000000000003b R09: fffffbfff0b94b9c
[ 158.745626] R10: fffffbfff0b94b9b R11: ffffffff85ca5cdf R12: ffff888032f28000
[ 158.748405] R13: dffffc0000000000 R14: ffff8880335501b8 R15: 1ffff110068fcf72
[ 158.750638] FS: 0000000000000000(0000) GS:ffff888036000000(0000) knlGS:0000000000000000
[ 158.752944] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 158.755245] CR2: 00007fe8b45d21d0 CR3: 00000000340b4005 CR4: 0000000000360ef0
[ 158.757654] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 158.760012] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 158.762758] Call Trace:
[ 158.763882] ? dev_change_net_namespace+0xbb0/0xbb0
[ 158.766148] ? devlink_nl_cmd_set_doit+0x520/0x520
[ 158.768034] ? dev_change_net_namespace+0xbb0/0xbb0
[ 158.769870] ops_exit_list.isra.0+0xa8/0x150
[ 158.771544] cleanup_net+0x446/0x8f0
[ 158.772945] ? unregister_pernet_operations+0x4a0/0x4a0
[ 158.775294] process_one_work+0xa1a/0x1740
[ 158.776896] ? pwq_dec_nr_in_flight+0x310/0x310
[ 158.779143] ? do_raw_spin_lock+0x11b/0x280
[ 158.780848] worker_thread+0x9e/0x1060
[ 158.782500] ? process_one_work+0x1740/0x1740
[ 158.784454] kthread+0x31b/0x420
[ 158.786082] ? __kthread_create_on_node+0x3f0/0x3f0
[ 158.788286] ret_from_fork+0x3a/0x50
[ 158.789871] ---[ end trace defd6c657c71f936 ]---
[ 158.792273] RIP: 0010:default_device_exit.cold+0x1d/0x1f
[ 158.795478] Code: 84 e8 18 c9 3e fe 0f 0b e9 70 90 ff ff e8 36 e4 52 fe 89 d9 4c 89 e2 48 c7 c6 80 d6 25 84 48 c7 c7 20 c0 25 84 e8 f4 c8 3e
[ 158.804854] RSP: 0018:ffff8880347e7b90 EFLAGS: 00010282
[ 158.807865] RAX: 000000000000003b RBX: 00000000ffffffef RCX: 0000000000000000
[ 158.811794] RDX: 0000000000000000 RSI: ffffffff8128013d RDI: ffffed10068fcf64
[ 158.816652] RBP: ffff888033550170 R08: 000000000000003b R09: fffffbfff0b94b9c
[ 158.820930] R10: fffffbfff0b94b9b R11: ffffffff85ca5cdf R12: ffff888032f28000
[ 158.825113] R13: dffffc0000000000 R14: ffff8880335501b8 R15: 1ffff110068fcf72
[ 158.829899] FS: 0000000000000000(0000) GS:ffff888036000000(0000) knlGS:0000000000000000
[ 158.834923] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 158.838164] CR2: 00007fe8b45d21d0 CR3: 00000000340b4005 CR4: 0000000000360ef0
[ 158.841917] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 158.845149] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Fix this by checking if a device with the same name exists in init_net
and fallback to original code - dev%d to allocate name - in case it does.
This was found using syzkaller.
Fixes: aca51397d014 ("netns: Fix arbitrary net_device-s corruptions on net_ns stop.") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On initialization failure we have to delete the local fdb which was
inserted due to the default pvid creation. This problem has been present
since the inception of default_pvid. Note that currently there are 2 cases:
1) in br_dev_init() when br_multicast_init() fails
2) if register_netdevice() fails after calling ndo_init()
This patch takes care of both since br_vlan_flush() is called on both
occasions. Also the new fdb delete would be a no-op on normal bridge
device destruction since the local fdb would've been already flushed by
br_dev_delete(). This is not an issue for ports since nbp_vlan_init() is
called last when adding a port thus nothing can fail after it.
Reported-by: syzbot+88533dc8b582309bf3ee@syzkaller.appspotmail.com Fixes: 5be5a2df40f0 ("bridge: Add filtering support for default_pvid") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
board is controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/atm/iphase.c:2765 ia_ioctl() warn: potential spectre issue 'ia_dev' [r] (local cap)
drivers/atm/iphase.c:2774 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2782 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2816 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2823 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2830 ia_ioctl() warn: potential spectre issue '_ia_dev' [r] (local cap)
drivers/atm/iphase.c:2845 ia_ioctl() warn: possible spectre second half. 'iadev'
drivers/atm/iphase.c:2856 ia_ioctl() warn: possible spectre second half. 'iadev'
Fix this by sanitizing board before using it to index ia_dev and _ia_dev
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some applications set tiny SO_SNDBUF values and expect
TCP to just work. Recent patches to address CVE-2019-11478
broke them in case of losses, since retransmits might
be prevented.
We should allow these flows to make progress.
This patch allows the first and last skb in retransmit queue
to be split even if memory limits are hit.
It also adds the some room due to the fact that tcp_sendmsg()
and tcp_sendpage() might overshoot sk_wmem_queued by about one full
TSO skb (64KB size). Note this allowance was already present
in stable backports for kernels < 4.15
Note for < 4.15 backports :
tcp_rtx_queue_tail() will probably look like :
Fixes: f070ef2ac667 ("tcp: tcp_fragment() should apply sane memory limits") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Andrew Prout <aprout@ll.mit.edu> Tested-by: Andrew Prout <aprout@ll.mit.edu> Tested-by: Jonathan Lemon <jonathan.lemon@gmail.com> Tested-by: Michal Kubecek <mkubecek@suse.cz> Acked-by: Neal Cardwell <ncardwell@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Acked-by: Christoph Paasch <cpaasch@apple.com> Cc: Jonathan Looney <jtl@netflix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for this one as well.
Jonathan Teh (@jonathan-teh) reported and tested the quirk.
Reference: https://github.com/sriemer/fix-linux-mouse/issues/15
If a quota bit is set in NFACCT_FLAGS but the NFACCT_QUOTA parameter is
missing then a NULL pointer dereference is triggered. CAP_NET_ADMIN is
required to trigger the bug.
Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CTR_EL0.{CWG,ERG} are 0b0000 then they must be interpreted to have
their architecturally maximum values, which defeats the use of
FTR_HIGHER_SAFE when sanitising CPU ID registers on heterogeneous
machines.
Introduce FTR_HIGHER_OR_ZERO_SAFE so that these fields effectively
saturate at zero.
Fixes: 3c739b571084 ("arm64: Keep track of CPU feature registers") Cc: <stable@vger.kernel.org> # 4.4.y only Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log