When a jump_whitelist bitmap is reused, it needs to be cleared.
Currently this is done with memset() and the size calculation assumes
bitmaps are made of 32-bit words, not longs. So on 64-bit
architectures, only the first half of the bitmap is cleared.
If some whitelist bits are carried over between successive batches
submitted on the same context, this will presumably allow embedding
the rogue instructions that we're trying to reject.
Use bitmap_zero() instead, which gets the calculation right.
Fixes: f8c08d8faee5 ("drm/i915/cmdparser: Add support for backward jumps") Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some circumstances the RC6 context can get corrupted. We can detect
this and take the required action, that is disable RC6 and runtime PM.
The HW recovers from the corrupted state after a system suspend/resume
cycle, so detect the recovery and re-enable RC6 and runtime PM.
v2: rebase (Mika)
v3:
- Move intel_suspend_gt_powersave() to the end of the GEM suspend
sequence.
- Add commit message.
v4:
- Rebased on intel_uncore_forcewake_put(i915->uncore, ...) API
change.
v5: rebased on gem/gt split (Mika)
Signed-off-by: Imre Deak <imre.deak@intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In BXT/APL, device 2 MMIO reads from MIPI controller requires its PLL
to be turned ON. When MIPI PLL is turned off (MIPI Display is not
active or connected), and someone (host or GT engine) tries to read
MIPI registers, it causes hard hang. This is a hardware restriction
or limitation.
Driver by itself doesn't read MIPI registers when MIPI display is off.
But any userspace application can submit unprivileged batch buffer for
execution. In that batch buffer there can be mmio reads. And these
reads are allowed even for unprivileged applications. If these
register reads are for MIPI DSI controller and MIPI display is not
active during that time, then the MMIO read operation causes system
hard hang and only way to recover is hard reboot. A genuine
process/application won't submit batch buffer like this and doesn't
cause any issue. But on a compromised system, a malign userspace
process/app can generate such batch buffer and can trigger system
hard hang (denial of service attack).
The fix is to lower the internal MMIO timeout value to an optimum
value of 950us as recommended by hardware team. If the timeout is
beyond 1ms (which will hit for any value we choose if MMIO READ on a
DSI specific register is performed without PLL ON), it causes the
system hang. But if the timeout value is lower than it will be below
the threshold (even if timeout happens) and system will not get into
a hung state. This will avoid a system hang without losing any
programming or GT interrupts, taking the worst case of lowest CDCLK
frequency and early DC5 abort into account.
Signed-off-by: Uma Shankar <uma.shankar@intel.com> Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the gen instruction macros (e.g. MI_DISPLAY_FLIP) have the
length directly encoded in them. Since these are used directly in
the tables, the Length becomes part of the comparison used for
matching during parsing. Thus, if the cmd being parsed has a
different length to that in the table, it is not matched and the
cmd is accepted via the default variable length path.
Fix by masking out everything except the Opcode in the cmd tables
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Tyler Hicks <tyhicks@canonical.com> Reviewed-by: Chris Wilson <chris.p.wilson@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To keep things manageable, the pre-gen9 cmdparser does not
attempt to track any form of nested BB_START's. This did not
prevent usermode from using nested starts, or even chained
batches because the cmdparser is not strictly enforced pre gen9.
Instead, the existence of a nested BB_START would cause the batch
to be emitted in insecure mode, and any privileged capabilities
would not be available.
For Gen9, the cmdparser becomes mandatory (for BCS at least), and
so not providing any form of nested BB_START support becomes
overly restrictive. Any such batch will simply not run.
We make heavy use of backward jumps in igt, and it is much easier
to add support for this restricted subset of nested jumps, than to
rewrite the whole of our test suite to avoid them.
Add the required logic to support limited backward jumps, to
instructions that have already been validated by the parser.
Note that it's not sufficient to simply approve any BB_START
that jumps backwards in the buffer because this would allow an
attacker to embed a rogue instruction sequence within the
operand words of a harmless instruction (say LRI) and jump to
that.
We introduce a bit array to track every instr offset successfully
validated, and test the target of BB_START against this. If the
target offset hits, it is re-written to the same offset in the
shadow buffer and the BB_START cmd is allowed.
Note: This patch deliberately ignores checkpatch issues in the
cmdtables, in order to match the style of the surrounding code.
We'll correct the entire file in one go in a later patch.
v2: set dispatch secure late (Mika)
v3: rebase (Mika)
v4: Clear whitelist on each parse
Minor review updates (Chris)
v5: Correct backward jump batching
v6: fix compilation error due to struct eb shuffle (Mika)
Cc: Tony Luck <tony.luck@intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Chris Wilson <chris.p.wilson@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For gen9 we enable cmdparsing on the BCS ring, specifically
to catch inadvertent accesses to sensitive registers
Unlike gen7/hsw, we use the parser only to block certain
registers. We can rely on h/w to block restricted commands,
so the command tables only provide enough info to allow the
parser to delineate each command, and identify commands that
access registers.
Note: This patch deliberately ignores checkpatch issues in
favour of matching the style of the surrounding code. We'll
correct the entire file in one go in a later patch.
v3: rebase (Mika)
v4: Add RING_TIMESTAMP registers to whitelist (Jon)
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Chris Wilson <chris.p.wilson@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In "drm/i915: Add support for mandatory cmdparsing" we introduced the
concept of mandatory parsing. This allows the cmdparser to be invoked
even when user passes batch_len=0 to the execbuf ioctl's.
However, the cmdparser needs to know the extents of the buffer being
scanned. Refactor the code to ensure the cmdparser uses the actual
object size, instead of the incoming length, if user passes 0.
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Tyler Hicks <tyhicks@canonical.com> Reviewed-by: Chris Wilson <chris.p.wilson@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For Gen7, the original cmdparser motive was to permit limited
use of register read/write instructions in unprivileged BB's.
This worked by copying the user supplied bb to a kmd owned
bb, and running it in secure mode, from the ggtt, only if
the scanner finds no unsafe commands or registers.
For Gen8+ we can't use this same technique because running bb's
from the ggtt also disables access to ppgtt space. But we also
do not actually require 'secure' execution since we are only
trying to reduce the available command/register set. Instead we
will copy the user buffer to a kmd owned read-only bb in ppgtt,
and run in the usual non-secure mode.
Note that ro pages are only supported by ppgtt (not ggtt), but
luckily that's exactly what we need.
Add the required paths to map the shadow buffer to ppgtt ro for Gen8+
v2: IS_GEN7/IS_GEN (Mika)
v3: rebase
v4: rebase
v5: rebase
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Chris Wilson <chris.p.wilson@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The existing cmdparser for gen7 can be bypassed by specifying
batch_len=0 in the execbuf call. This is safe because bypassing
simply reduces the cmd-set available.
In a later patch we will introduce cmdparsing for gen9, as a
security measure, which must be strictly enforced since without
it we are vulnerable to DoS attacks.
Introduce the concept of 'required' cmd parsing that cannot be
bypassed by submitting zero-length bb's.
v2: rebase (Mika)
v2: rebase (Mika)
v3: fix conflict on engine flags (Mika)
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Chris Wilson <chris.p.wilson@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retroactively stop reporting support for secure batches
through the api for gen6+ so that older binaries trigger
the fallback path instead.
Older binaries use secure batches pre gen6 to access resources
that are not available to normal usermode processes. However,
all known userspace explicitly checks for HAS_SECURE_BATCHES
before relying on the secure batch feature.
Since there are no known binaries relying on this for newer gens
we can kill secure batches from gen6, via I915_PARAM_HAS_SECURE_BATCHES.
v2: rebase (Mika)
v3: rebase (Mika)
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Tyler Hicks <tyhicks@canonical.com> Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by: Chris Wilson <chris.p.wilson@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GVT is not propagating the PTE bits, and is always setting the
read-write bit, thus breaking read-only support.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Zhenyu Wang <zhenyuw@linux.intel.com> Cc: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Matthew Auld <matthew.william.auld@gmail.com> Reviewed-by: Jon Bloomfield <jon.bloomfield@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180712185315.3288-3-chris@chris-wilson.co.uk Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hook up the flags to allow read-only ppGTT mappings for gen8+
v2: Include a selftest to check that writes to a readonly PTE are
dropped
v3: Don't duplicate cpu_check() as we can just reuse it, and even worse
don't wholesale copy the theory-of-operation comment from igt_ctx_exec
without changing it to explain the intention behind the new test!
v4: Joonas really likes magic mystery values
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Matthew Auld <matthew.william.auld@gmail.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180712185315.3288-2-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can set a bit inside the ppGTT PTE to indicate a page is read-only;
writes from the GPU will be discarded. We can use this to protect pages
and in particular support read-only userptr mappings (necessary for
importing PROT_READ vma).
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com> Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Matthew Auld <matthew.william.auld@gmail.com> Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180712185315.3288-1-chris@chris-wilson.co.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cgroup writeback tries to refresh the associated wb immediately if the
current wb is dead. This is to avoid keeping issuing IOs on the stale
wb after memcg - blkcg association has changed (ie. when blkcg got
disabled / enabled higher up in the hierarchy).
Unfortunately, the logic gets triggered spuriously on inodes which are
associated with dead cgroups. When the logic is triggered on dead
cgroups, the attempt fails only after doing quite a bit of work
allocating and initializing a new wb.
While c3aab9a0bd91 ("mm/filemap.c: don't initiate writeback if mapping
has no dirty pages") alleviated the issue significantly as it now only
triggers when the inode has dirty pages. However, the condition can
still be triggered before the inode is switched to a different cgroup
and the logic simply doesn't make sense.
Skip the immediate switching if the associated memcg is dying.
This is a simplified version of the following two patches:
Functions like filemap_write_and_wait_range() should do nothing if inode
has no dirty pages or pages currently under writeback. But they anyway
construct struct writeback_control and this does some atomic operations if
CONFIG_CGROUP_WRITEBACK=y - on fast path it locks inode->i_lock and
updates state of writeback ownership, on slow path might be more work.
Current this path is safely avoided only when inode mapping has no pages.
For example generic_file_read_iter() calls filemap_write_and_wait_range()
at each O_DIRECT read - pretty hot path.
This patch skips starting new writeback if mapping has no dirty tags set.
If writeback is already in progress filemap_write_and_wait_range() will
wait for it.
Link: http://lkml.kernel.org/r/156378816804.1087.8607636317907921438.stgit@buzz Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reviewed-by: Jan Kara <jack@suse.cz> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ECC (memory error detection and correction) mechanism can be
activated or not, controlled by the ECCDIS bit in CAN_MECR. When
disabled, updates on indications and reporting registers are stopped.
So if want to disable ECC completely, had better assert ECCDIS bit, not
just mask the related interrupts.
Fixes: cdce844865be ("can: flexcan: add vf610 support for FlexCAN") Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com> Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.
If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.
The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When rmmod hip04_eth.ko, we can get the following warning:
Task track: rmmod(1623)>bash(1591)>login(1581)>init(1)
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1623 at kernel/irq/manage.c:1557 __free_irq+0xa4/0x2ac()
Trying to free already-free IRQ 200
Modules linked in: ping(O) pramdisk(O) cpuinfo(O) rtos_snapshot(O) interrupt_ctrl(O) mtdblock mtd_blkdevrtfs nfs_acl nfs lockd grace sunrpc xt_tcpudp ipt_REJECT iptable_filter ip_tables x_tables nf_reject_ipv
CPU: 0 PID: 1623 Comm: rmmod Tainted: G O 4.4.193 #1
Hardware name: Hisilicon A15
[<c020b408>] (rtos_unwind_backtrace) from [<c0206624>] (show_stack+0x10/0x14)
[<c0206624>] (show_stack) from [<c03f2be4>] (dump_stack+0xa0/0xd8)
[<c03f2be4>] (dump_stack) from [<c021a780>] (warn_slowpath_common+0x84/0xb0)
[<c021a780>] (warn_slowpath_common) from [<c021a7e8>] (warn_slowpath_fmt+0x3c/0x68)
[<c021a7e8>] (warn_slowpath_fmt) from [<c026876c>] (__free_irq+0xa4/0x2ac)
[<c026876c>] (__free_irq) from [<c0268a14>] (free_irq+0x60/0x7c)
[<c0268a14>] (free_irq) from [<c0469e80>] (release_nodes+0x1c4/0x1ec)
[<c0469e80>] (release_nodes) from [<c0466924>] (__device_release_driver+0xa8/0x104)
[<c0466924>] (__device_release_driver) from [<c0466a80>] (driver_detach+0xd0/0xf8)
[<c0466a80>] (driver_detach) from [<c0465e18>] (bus_remove_driver+0x64/0x8c)
[<c0465e18>] (bus_remove_driver) from [<c02935b0>] (SyS_delete_module+0x198/0x1e0)
[<c02935b0>] (SyS_delete_module) from [<c0202ed0>] (__sys_trace_return+0x0/0x10)
---[ end trace bb25d6123d849b44 ]---
Currently "rmmod hip04_eth.ko" call free_irq more than once
as devres_release_all and hip04_remove both call free_irq.
This results in a 'Trying to free already-free IRQ' warning.
To solve the problem free_irq has been moved out of hip04_remove.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Endpoints with a maxpacket length of 0 are probably useless. They
can't transfer any data, and it's not at all unlikely that an HCD will
crash or hang when trying to handle an URB for such an endpoint.
Currently the USB core does not check for endpoints having a maxpacket
value of 0. This patch adds a check, printing a warning and skipping
over any endpoints it catches.
Now, the USB spec does not rule out endpoints having maxpacket = 0.
But since they wouldn't have any practical use, there doesn't seem to
be any good reason for us to accept them.
The loop that reads all the IBS MSRs into *buf stopped one MSR short of
reading the IbsOpData register, which contains the RipInvalid status bit.
Fix the offset_max assignment so the MSR gets read, so the RIP invalid
evaluation is based on what the IBS h/w output, instead of what was
left in memory.
Signed-off-by: Kim Phillips <kim.phillips@amd.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Borislav Petkov <bp@alien8.de> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Fixes: d47e8238cd76 ("perf/x86-ibs: Take instruction pointer from ibs sample") Link: https://lkml.kernel.org/r/20191023150955.30292-1-kim.phillips@amd.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We meet several NULL pointer issues if configfs_composite_unbind
and composite_setup (or composite_disconnect) are running together.
These issues occur when do the function switch stress test, the
configfs_compsoite_unbind is called from user mode by
echo "" to /sys/../UDC entry, and meanwhile, the setup interrupt
or disconnect interrupt occurs by hardware. The composite_setup
will get the cdev from get_gadget_data, but configfs_composite_unbind
will set gadget data as NULL, so the NULL pointer issue occurs.
This concurrent is hard to reproduce by native kernel, but can be
reproduced by android kernel.
In this commit, we introduce one spinlock belongs to structure
gadget_info since we can't use the same spinlock in usb_composite_dev
due to exclusive running together between composite_setup and
configfs_composite_unbind. And one bit flag 'unbind' to indicate the
code is at unbind routine, this bit is needed due to we release the
lock at during configfs_composite_unbind sometimes, and composite_setup
may be run at that time.
composite_dev_cleanup call from the failure of configfs_composite_bind
frees up the cdev->os_desc_req and cdev->req. If the previous calls of
bind and unbind is successful these will carry stale values.
Consider the below sequence of function calls:
configfs_composite_bind()
composite_dev_prepare()
- Allocate cdev->req, cdev->req->buf
composite_os_desc_req_prepare()
- Allocate cdev->os_desc_req, cdev->os_desc_req->buf
configfs_composite_unbind()
composite_dev_cleanup()
- free the cdev->os_desc_req->buf and cdev->req->buf
Next composition switch
configfs_composite_bind()
- If it fails goto err_comp_cleanup will call the
composite_dev_cleanup() function
composite_dev_cleanup()
- calls kfree up with the stale values of cdev->req->buf and
cdev->os_desc_req from the previous configfs_composite_bind
call. The free call on these stale values leads to double free.
Hence, Fix this issue by setting request and buffer pointer to NULL after
kfree.
Fix interrupt storm generated by endpoints when working in FIFO mode.
The TX_COMPLETE interrupt is used only by control endpoints processing.
Do not enable it for other types of endpoints.
Check memory resource existence before releasing it to avoid NULL
pointer dereference
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: Ran Wang <ran.wang_1@nxp.com> Reviewed-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The IFF_BONDING means bonding master or bonding slave device.
->ndo_add_slave() sets IFF_BONDING flag and ->ndo_del_slave() unsets
IFF_BONDING flag.
bond0<--bond1
Both bond0 and bond1 are bonding device and these should keep having
IFF_BONDING flag until they are removed.
But bond1 would lose IFF_BONDING at ->ndo_del_slave() because that routine
do not check whether the slave device is the bonding type or not.
This patch adds the interface type check routine before removing
IFF_BONDING flag.
Test commands:
ip link add bond0 type bond
ip link add bond1 type bond
ip link set bond1 master bond0
ip link set bond1 nomaster
ip link del bond1 type bond
ip link add bond1 type bond
BUG: KCSAN: data-race in update_defense_level / update_defense_level
read to 0xffffffff861a6260 of 4 bytes by task 3006 on cpu 1:
update_defense_level+0x621/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:177
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
write to 0xffffffff861a6260 of 4 bytes by task 7333 on cpu 0:
update_defense_level+0xa62/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:205
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7333 Comm: kworker/0:5 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events defense_work_handler
Indeed, old_secure_tcp is currently a static variable, while it
needs to be a per netns variable.
Fixes: a0840e2e165a ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
A customer reports that after a devloss, an ADISC failure is logged. It
turns out the ADISC flag is set even the user explicitly set lpfc_use_adisc
= 0.
[Sat Dec 22 22:55:58 2018] lpfc 0000:82:00.0: 2:(0):0203 Devloss timeout on WWPN 50:01:43:80:12:8e:40:20 NPort x05df00 Data: x82000000 x8 xa
[Sat Dec 22 23:08:20 2018] lpfc 0000:82:00.0: 2:(0):2755 ADISC failure DID:05DF00 Status:x9/x70000
[mkp: fixed Hannes' email]
Fixes: 92d7f7b0cde3 ("[SCSI] lpfc: NPIV: add NPIV support on top of SLI-3") Cc: Dick Kennedy <dick.kennedy@broadcom.com> Cc: James Smart <james.smart@broadcom.com> Link: https://lore.kernel.org/r/20191022072112.132268-1-dwagner@suse.de Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: James Smart <james.smart@broadcom.com> Signed-off-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PCI Tegra controller conversion to a device tree configurable
driver in commit d1523b52bff3 ("PCI: tegra: Move PCIe driver
to drivers/pci/host") implied that code for the driver can be
compiled in for a kernel supporting multiple platforms.
Unfortunately, a blind move of the code did not check that some of the
quirks that were applied in arch/arm (eg enabling Relaxed Ordering on
all PCI devices - since the quirk hook erroneously matches PCI_ANY_ID
for both Vendor-ID and Device-ID) are now applied in all kernels that
compile the PCI Tegra controlled driver, DT and ACPI alike.
This is completely wrong, in that enablement of Relaxed Ordering is only
required by default in Tegra20 platforms as described in the Tegra20
Technical Reference Manual (available at
https://developer.nvidia.com/embedded/downloads#?search=tegra%202 in
Section 34.1, where it is mentioned that Relaxed Ordering bit needs to
be enabled in its root ports to avoid deadlock in hardware) and in the
Tegra30 platforms for the same reasons (unfortunately not documented
in the TRM).
There is no other strict requirement on PCI devices Relaxed Ordering
enablement on any other Tegra platforms or PCI host bridge driver.
Fix this quite upsetting situation by limiting the vendor and device IDs
to which the Relaxed Ordering quirk applies to the root ports in
question, reported above.
Configfs abuses symlink(2). Unlike the normal filesystems, it
wants the target resolved at symlink(2) time, like link(2) would've
done. The problem is that ->symlink() is called with the parent
directory locked exclusive, so resolving the target inside the
->symlink() is easily deadlocked.
Short of really ugly games in sys_symlink() itself, all we can
do is to unlock the parent before resolving the target and
relock it after. However, that invalidates the checks done
by the caller of ->symlink(), so we have to
* check that dentry is still where it used to be
(it couldn't have been moved, but it could've been unhashed)
* recheck that it's still negative (somebody else
might've successfully created a symlink with the same name
while we were looking the target up)
* recheck the permissions on the parent directory.
Cc: stable@vger.kernel.org Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a small slab info leak due to a failure to clear the command buffer
at allocation.
The first 16 bytes of the command buffer are always sent to the device
in pcan_usb_send_cmd() even though only the first two may have been
initialised in case no argument payload is provided (e.g. when waiting
for a response).
Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core") Cc: stable <stable@vger.kernel.org> # 3.4 Reported-by: syzbot+863724e7128e14b26732@syzkaller.appspotmail.com Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When decoding a buffer received from PCAN-USB, the first timestamp read in
a packet is a 16-bit coded time base, and the next ones are an 8-bit
offset to this base, regardless of the type of packet read.
This patch corrects a potential loss of synchronization by using a
timestamp index read from the buffer, rather than an index of received
data packets, to determine on the sizeof the timestamp to be read from the
packet being decoded.
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.
It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.
Thanks to Wolfgang and Joe for bringing up the first idea.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be> Cc: Wolfgang Grandegger <wg@grandegger.com> Cc: Joe Burmeister <joe.burmeister@devtank.co.uk> Fixes: fa39b54ccf28 ("can: c_can: Get rid of pointless interrupts") Cc: linux-stable <stable@vger.kernel.org> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The copy_to_user() function returns the number of bytes remaining to be
copied. In this code, that positive return is checked at the end of the
function and we return zero/success. What we should do instead is
return -EFAULT.
Fixes: a7b4f989a629 ("netfilter: ipset: IP set core support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invoking the following commands on a 32-bit architecture with strict
alignment requirements (such as an ARMv7-based Raspberry Pi) results
in an alignment exception:
# nft add table ip test-ip4
# nft add chain ip test-ip4 output { type filter hook output priority 0; }
# nft add rule ip test-ip4 output quota 1025 bytes
The reason is that nft_quota_do_init() calls atomic64_set() on an
atomic64_t which is only aligned to 32-bit, not 64-bit, because it
succeeds struct nft_expr in memory which only contains a 32-bit pointer.
Fix by aligning the nft_expr private data to 64-bit.
This happens because __ceph_remove_cap() may queue a cap release
(__ceph_queue_cap_release) which can be scheduled before that cap is
removed from the inode list with
rb_erase(&cap->ci_node, &ci->i_caps);
And, when this finally happens, the use-after-free will occur.
This can be fixed by removing the cap from the inode list before being
removed from the session list, and thus eliminating the risk of an UAF.
Cc: stable@vger.kernel.org Signed-off-by: Luis Henriques <lhenriques@suse.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the current code, we use the atomic_cmpxchg() to serialize the output
of the dump_stack(), but this implementation suffers the thundering herd
problem. We have observed such kind of livelock on a Marvell cn96xx
board(24 cpus) when heavily using the dump_stack() in a kprobe handler.
Actually we can let the competitors to wait for the releasing of the
lock before jumping to atomic_cmpxchg(). This will definitely mitigate
the thundering herd problem. Thanks Linus for the suggestion.
[akpm@linux-foundation.org: fix comment] Link: http://lkml.kernel.org/r/20191030031637.6025-1-haokexin@gmail.com Fixes: b58d977432c8 ("dump_stack: serialize the output from dump_stack()") Signed-off-by: Kevin Hao <haokexin@gmail.com> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
/proc/pagetypeinfo is a debugging tool to examine internal page
allocator state wrt to fragmentation. It is not very useful for any
other use so normal users really do not need to read this file.
Waiman Long has noticed that reading this file can have negative side
effects because zone->lock is necessary for gathering data and that a)
interferes with the page allocator and its users and b) can lead to hard
lockups on large machines which have very long free_list.
Reduce both issues by simply not exporting the file to regular users.
Link: http://lkml.kernel.org/r/20191025072610.18526-2-mhocko@kernel.org Fixes: 467c996c1e19 ("Print out statistics in relation to fragmentation avoidance to /proc/pagetypeinfo") Signed-off-by: Michal Hocko <mhocko@suse.com> Reported-by: Waiman Long <longman@redhat.com> Acked-by: Mel Gorman <mgorman@suse.de> Acked-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Waiman Long <longman@redhat.com> Acked-by: Rafael Aquini <aquini@redhat.com> Acked-by: David Rientjes <rientjes@google.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: David Hildenbrand <david@redhat.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Roman Gushchin <guro@fb.com> Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Cc: Jann Horn <jannh@google.com> Cc: Song Liu <songliubraving@fb.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The unsolicited event handler for the headphone jack on CA0132 codec
driver tries to reschedule the another delayed work with
cancel_delayed_work_sync(). It's no good idea, unfortunately,
especially after we changed the work queue to the standard global
one; this may lead to a stall because both works are using the same
global queue.
Fix it by dropping the _sync but does call cancel_delayed_work()
instead.
For Focusrite Saffire Pro i/o, the lowest 8 bits of register represents
configured source of sampling clock. The next lowest 8 bits represents
whether the configured source is actually detected or not just after
the register is changed for the source.
Current implementation evaluates whole the register to detect configured
source. This results in failure due to the next lowest 8 bits when the
source is connected in advance.
The function nfc_put_device(dev) is called twice to drop the reference
to dev when there is no associated local llcp. Remove one of them to fix
the bug.
Fixes: 52feb444a903 ("NFC: Extend netlink interface for LTO, RW, and MIUX parameters support") Fixes: d9b8d8e19b07 ("NFC: llcp: Service Name Lookup netlink interface") Signed-off-by: Pan Bian <bianpan2016@163.com> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While rebooting the system with SR-IOV vfs enabled leads
to below crash due to recurrence of __qede_remove() on the VF
devices (first from .shutdown() flow of the VF itself and
another from PF's .shutdown() flow executing pci_disable_sriov())
This patch adds a safeguard in __qede_remove() flow to fix this,
so that driver doesn't attempt to remove "already removed" devices.
The variable nfcid_skb is not changed in the callee nfc_hci_get_param()
if error occurs. Consequently, the freed variable nfcid_skb will be
freed again, resulting in a double free bug. Set nfcid_skb to NULL after
releasing it to fix the bug.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The address of fw_vsc_cfg is on stack. Releasing it with devm_kfree() is
incorrect, which may result in a system crash or other security impacts.
The expected object to free is *fw_vsc_cfg.
Signed-off-by: Pan Bian <bianpan2016@163.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A malicious device may give half an answer when asked
for its MTU. The driver will proceed after this with
a garbage MTU. Anything but a complete answer must be treated
as an error.
V2: used sizeof as request by Alexander
Reported-and-tested-by: syzbot+0631d878823ce2411636@syzkaller.appspotmail.com Signed-off-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
zhangyi (F) [Wed, 6 Nov 2019 09:43:52 +0000 (17:43 +0800)]
fs/dcache: move security_d_instantiate() behind attaching dentry to inode
During backport 1e2e547a93a "do d_instantiate/unlock_new_inode
combinations safely", there was a error instantiating sequence of
attaching dentry to inode and calling security_d_instantiate().
Before commit ce23e640133 "->getxattr(): pass dentry and inode as
separate arguments" and b96809173e9 "security_d_instantiate(): move to
the point prior to attaching dentry to inode", security_d_instantiate()
should be called beind __d_instantiate(), otherwise it will trigger
below problem when CONFIG_SECURITY_SMACK on ext4 was enabled because
d_inode(dentry) used by ->getxattr() is NULL before __d_instantiate()
instantiate inode.
The intention in the previous patch was to only place the processor
tables in the .rodata section if big.Little was being built and we
wanted the branch target hardening, but instead (due to the way it
was tested) it ended up always placing the tables into the .rodata
section.
Although harmless, let's correct this anyway.
Fixes: 3a4d0c2172bc ("ARM: ensure that processor vtables is not lost after boot") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek Szyprowski reported problems with CPU hotplug in current kernels.
This was tracked down to the processor vtables being located in an
init section, and therefore discarded after kernel boot, despite being
required after boot to properly initialise the non-boot CPUs.
Arrange for these tables to end up in .rodata when required.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Krzysztof Kozlowski <krzk@kernel.org> Fixes: 383fb3ee8024 ("ARM: spectre-v2: per-CPU vtables to work around big.Little systems") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In big.Little systems, some CPUs require the Spectre workarounds in
paths such as the context switch, but other CPUs do not. In order
to handle these differences, we need per-CPU vtables.
We are unable to use the kernel's per-CPU variables to support this
as per-CPU is not initialised at times when we need access to the
vtables, so we have to use an array indexed by logical CPU number.
We use an array-of-pointers to avoid having function pointers in
the kernel's read/write .data section.
Note: Added include of linux/slab.h in arch/arm/smp.c.
Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow the way we access members of the processor vtable to be changed
at compile time. We will need to move to per-CPU vtables to fix the
Spectre variant 2 issues on big.Little systems.
However, we have a couple of calls that do not need the vtable
treatment, and indeed cause a kernel warning due to the (later) use
of smp_processor_id(), so also introduce the PROC_TABLE macro for
these which always use CPU 0's function pointers.
Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split out the lookup of the processor type and associated error handling
from the rest of setup_processor() - we will need to use this in the
secondary CPU bringup path for big.Little Spectre variant 2 mitigation.
Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In vfp_preserve_user_clear_hwstate, ufp_exc->fpinst2 gets assigned to
itself. It should actually be hwstate->fpinst2 that gets assigned to the
ufp_exc field.
When Spectre mitigation is required, __put_user() needs to include
check_uaccess. This is already the case for put_user(), so just make
__put_user() an alias of put_user().
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A mispredicted conditional call to set_fs could result in the wrong
addr_limit being forwarded under speculation to a subsequent access_ok
check, potentially forming part of a spectre-v1 attack using uaccess
routines.
This patch prevents this forwarding from taking place, but putting heavy
barriers in set_fs after writing the addr_limit.
Porting commit c2f0ad4fc089cff8 ("arm64: uaccess: Prevent speculative use
of the current addr_limit").
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copy events to user using __copy_to_user() rather than copy members of
individually with __put_user_error().
This has the benefit of disabling/enabling PAN once per event intead of
once per event member.
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use __copy_to_user() rather than __put_user_error() for individual
members when saving VFP state.
This has the benefit of disabling/enabling PAN once per copied struct
intead of once per write.
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When saving the ARM integer registers, use __copy_to_user() to
copy them into user signal frame, rather than __put_user_error().
This has the benefit of disabling/enabling PAN once for the whole copy
intead of once per write.
Signed-off-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Reviewed-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Spectre variant 1 attacks are about this sequence of pseudo-code:
index = load(user-manipulated pointer);
access(base + index * stride);
In order for the cache side-channel to work, the access() must me made
to memory which userspace can detect whether cache lines have been
loaded. On 32-bit ARM, this must be either user accessible memory, or
a kernel mapping of that same user accessible memory.
The problem occurs when the load() speculatively loads privileged data,
and the subsequent access() is made to user accessible memory.
Any load() which makes use of a user-maniplated pointer is a potential
problem if the data it has loaded is used in a subsequent access. This
also applies for the access() if the data loaded by that access is used
by a subsequent access.
Harden the get_user() accessors against Spectre attacks by forcing out
of bounds addresses to a NULL pointer. This prevents get_user() being
used as the load() step above. As a side effect, put_user() will also
be affected even though it isn't implicated.
Also harden copy_from_user() by redoing the bounds check within the
arm_copy_from_user() code, and NULLing the pointer if out of bounds.
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing __get_user() for spectre variant 1 is not sane: we would have to
add address space bounds checking in order to validate that the location
should be accessed, and then zero the address if found to be invalid.
Since __get_user() is supposed to avoid the bounds check, and this is
exactly what get_user() does, there's no point having two different
implementations that are doing the same thing. So, when the Spectre
workarounds are required, make __get_user() an alias of get_user().
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Borrow the x86 implementation of __inttype() to use in get_user() to
select an integer type suitable to temporarily hold the result value.
This is necessary to avoid propagating the volatile nature of the
result argument, which can cause the following warning:
lib/iov_iter.c:413:5: warning: optimization may eliminate reads and/or writes to register variables [-Wvolatile-register-var]
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__get_user_error() is used as a fast accessor to make copying structure
members as efficient as possible. However, with software PAN and the
recent Spectre variant 1, the efficiency is reduced as these are no
longer fast accessors.
In the case of software PAN, it has to switch the domain register around
each access, and with Spectre variant 1, it would have to repeat the
access_ok() check for each access.
Rather than using __get_user_error() to copy each semops element member,
copy each semops element in full using __copy_from_user().
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__get_user_error() is used as a fast accessor to make copying structure
members in the signal handling path as efficient as possible. However,
with software PAN and the recent Spectre variant 1, the efficiency is
reduced as these are no longer fast accessors.
In the case of software PAN, it has to switch the domain register around
each access, and with Spectre variant 1, it would have to repeat the
access_ok() check for each access.
Use __copy_from_user() rather than __get_user_err() for individual
members when restoring VFP state.
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__get_user_error() is used as a fast accessor to make copying structure
members in the signal handling path as efficient as possible. However,
with software PAN and the recent Spectre variant 1, the efficiency is
reduced as these are no longer fast accessors.
In the case of software PAN, it has to switch the domain register around
each access, and with Spectre variant 1, it would have to repeat the
access_ok() check for each access.
It becomes much more efficient to use __copy_from_user() instead, so
let's use this for the ARM integer registers.
Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prevent speculation at the syscall table decoding by clamping the index
used to zero on invalid system call numbers, and using the csdb
speculative barrier.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Mark Rutland <mark.rutland@arm.com> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add an implementation of the array_index_mask_nospec() function for
mitigating Spectre variant 1 throughout the kernel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Mark Rutland <mark.rutland@arm.com> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add assembly and C macros for the new CSDB instruction.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Mark Rutland <mark.rutland@arm.com> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warn at error level if the context switching function is not what we
are expecting. This can happen with big.Little systems, which we
currently do not support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add firmware based hardening for cores that require more complex
handling in firmware.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to prevent aliasing attacks on the branch predictor,
invalidate the BTB or instruction cache on CPUs that are known to be
affected when taking an abort on a address that is outside of a user
task limit:
If the IBE bit is not set, then there is little point to enabling the
workaround.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the branch predictor hardening is enabled, firmware must have set
the IBE bit in the auxiliary control register. If this bit has not
been set, the Spectre workarounds will not be functional.
Add validation that this bit is set, and print a warning at alert level
if this is not the case.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Harden the branch predictor against Spectre v2 attacks on context
switches for ARMv7 and later CPUs. We do this by:
Cortex A9, A12, A17, A73, A75: invalidating the BTB.
Cortex A15, Brahma B15: invalidating the instruction cache.
Cortex A57 and Cortex A72 are not addressed in this patch.
Cortex R7 and Cortex R8 are also not addressed as we do not enforce
memory protection on these cores.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a Kconfig symbol for CPUs which are vulnerable to the Spectre
attacks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for per-processor bug checking - each processor function
descriptor gains a function pointer for this check, which must not be
an __init function. If non-NULL, this will be called whenever a CPU
enters the kernel via which ever path (boot CPU, secondary CPU startup,
CPU resuming, etc.)
This allows processor specific bug checks to validate that workaround
bits are properly enabled by firmware via all entry paths to the kernel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Check for CPU bugs when secondary processors are being brought online,
and also when CPUs are resuming from a low power mode. This gives an
opportunity to check that processor specific bug workarounds are
correctly enabled for all paths that a CPU re-enters the kernel.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prepare the processor bug infrastructure so that it can be expanded to
check for per-processor bugs.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CPU part numbers for Cortex A53, A57, A72, A73, A75 and the
Broadcom Brahma B15 CPU.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Boot-tested-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: David A. Long <dave.long@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An unfortunate consequence of having a strong typing for the input
values to the SMC call is that it also affects the type of the
return values, limiting r0 to 32 bits and r{1,2,3} to whatever
was passed as an input.
Let's turn everything into "unsigned long", which satisfies the
requirements of both architectures, and allows for the full
range of return values.
We've so far used the PSCI return codes for SMCCC because they
were extremely similar. But with the new ARM DEN 0070A specification,
"NOT_REQUIRED" (-2) is clashing with PSCI's "PSCI_RET_INVALID_PARAMS".
Let's bite the bullet and add SMCCC specific return codes. Users
can be repainted as and when required.
Acked-by: Will Deacon <will.deacon@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One of the major improvement of SMCCC v1.1 is that it only clobbers
the first 4 registers, both on 32 and 64bit. This means that it
becomes very easy to provide an inline version of the SMC call
primitive, and avoid performing a function call to stash the
registers that would otherwise be clobbered by SMCCC v1.0.
projects / linux-stable / log