mwifiex_cmd_802_11_ad_hoc_start() calls memcpy() without checking
the destination size may trigger a buffer overflower,
which a local user could use to cause denial of service
or the execution of arbitrary code.
Fix it by putting the length check before calling memcpy().
One of a class of bugs pointed out by Lars in a recent review.
iio_push_to_buffers_with_timestamp() assumes the buffer used is aligned
to the size of the timestamp (8 bytes). This is not guaranteed in
this driver which uses an array of smaller elements on the stack.
As Lars also noted this anti pattern can involve a leak of data to
userspace and that indeed can happen here. We close both issues by
moving to a suitable structure in the iio_priv() data.
This data is allocated with kzalloc() so no data can leak apart from
previous readings.
The explicit alignment of ts is not necessary in this case but
does make the code slightly less fragile so I have included it.
Apparently there has been a longstanding race between udev/systemd and
the module loader. Currently, the module loader sends a uevent right
after sysfs initialization, but before the module calls its init
function. However, some udev rules expect that the module has
initialized already upon receiving the uevent.
This race has been triggered recently (see link in references) in some
systemd mount unit files. For instance, the configfs module creates the
/sys/kernel/config mount point in its init function, however the module
loader issues the uevent before this happens. sys-kernel-config.mount
expects to be able to mount /sys/kernel/config upon receipt of the
module loading uevent, but if the configfs module has not called its
init function yet, then this directory will not exist and the mount unit
fails. A similar situation exists for sys-fs-fuse-connections.mount, as
the fuse sysfs mount point is created during the fuse module's init
function. If udev is faster than module initialization then the mount
unit would fail in a similar fashion.
To fix this race, delay the module KOBJ_ADD uevent until after the
module has finished calling its init routine.
I noticed that iounmap() of msgr_block_addr before return from
mpic_msgr_probe() in the error handling case is missing. So use
devm_ioremap() instead of just ioremap() when remapping the message
register block, so the mapping will be automatically released on
probe failure.
The on-disk quota format supports quota files with upto 2^32 blocks. Be
careful when computing quota file offsets in the quota files from block
numbers as they can overflow 32-bit types. Since quota files larger than
4GB would require ~26 millions of quota users, this is mostly a
theoretical concern now but better be careful, fuzzers would find the
problem sooner or later anyway...
Reviewed-by: Andreas Dilger <adilger@dilger.ca> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a module fails to load due to an error in prepare_coming_module(),
the following error handling in load_module() runs with
MODULE_STATE_COMING in module's state. Fix it by correctly setting
MODULE_STATE_GOING under "bug_cleanup" label.
The snd_seq_queue struct contains various flags in the bit fields.
Those are categorized to two different use cases, both of which are
protected by different spinlocks. That implies that there are still
potential risks of the bad operations for bit fields by concurrent
accesses.
For addressing the problem, this patch rearranges those flags to be
a standard bool instead of a bit field.
As reported on:
https://lore.kernel.org/linux-media/20190627222020.45909-1-willemdebruijn.kernel@gmail.com/
if gp8psk_usb_in_op() returns an error, the status var is not
initialized. Yet, this var is used later on, in order to
identify:
- if the device was already started;
- if firmware has loaded;
- if the LNBf was powered on.
Using status = 0 seems to ensure that everything will be
properly powered up.
So, instead of the proposed solution, let's just set
status = 0.
Reported-by: syzbot <syzkaller@googlegroups.com> Reported-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A kernel-infoleak was reported by syzbot, which was caused because
dbells was left uninitialized.
Using kzalloc() instead of kmalloc() fixes this issue.
Specify type alignment when declaring linker-section match-table entries
to prevent gcc from increasing alignment and corrupting the various
tables with padding (e.g. timers, irqchips, clocks, reserved memory).
This is specifically needed on x86 where gcc (typically) aligns larger
objects like struct of_device_id with static extent on 32-byte
boundaries which at best prevents matching on anything but the first
entry. Specifying alignment when declaring variables suppresses this
optimisation.
Here's a 64-bit example where all entries are corrupt as 16 bytes of
padding has been inserted before the first entry:
And here's a 32-bit example where the 8-byte-aligned table happens to be
placed on a 32-byte boundary so that all but the first entry are corrupt
due to the 28 bytes of padding inserted between entries:
and include <linux/const.h> in UAPI headers instead of <linux/kernel.h>.
The reason is to avoid indirect <linux/sysinfo.h> include when using
some network headers: <linux/netlink.h> or others -> <linux/kernel.h>
-> <linux/sysinfo.h>.
This indirect include causes on MUSL redefinition of struct sysinfo when
included both <sys/sysinfo.h> and some of UAPI headers:
In file included from x86_64-buildroot-linux-musl/sysroot/usr/include/linux/kernel.h:5,
from x86_64-buildroot-linux-musl/sysroot/usr/include/linux/netlink.h:5,
from ../include/tst_netlink.h:14,
from tst_crypto.c:13:
x86_64-buildroot-linux-musl/sysroot/usr/include/linux/sysinfo.h:8:8: error: redefinition of `struct sysinfo'
struct sysinfo {
^~~~~~~
In file included from ../include/tst_safe_macros.h:15,
from ../include/tst_test.h:93,
from tst_crypto.c:11:
x86_64-buildroot-linux-musl/sysroot/usr/include/sys/sysinfo.h:10:8: note: originally defined here
The driver must not call tty_wakeup() while holding its private lock as
line disciplines are allowed to call back into write() from
write_wakeup(), leading to a deadlock.
Also remove the unneeded work struct that was used to defer wakeup in
order to work around a possible race in ancient times (see comment about
n_tty write_chan() in commit 14b54e39b412 ("USB: serial: remove
changelogs and old todo entries")).
For an LCU update a read unit address configuration IO is required.
This is started using sleep_on(), which has early exit paths in case the
device is not usable for IO. For example when it is in offline processing.
In those cases the LCU update should fail and not be retried.
Therefore lcu_update_work checks if EOPNOTSUPP is returned or not.
Commit 41995342b40c ("s390/dasd: fix endless loop after read unit address configuration")
accidentally removed the EOPNOTSUPP return code from
read_unit_address_configuration(), which in turn might lead to an endless
loop of the LCU update in offline processing.
Fix by returning EOPNOTSUPP again if the device is not able to perform the
request.
Fixes: 41995342b40c ("s390/dasd: fix endless loop after read unit address configuration") Cc: stable@vger.kernel.org #5.3 Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the alc289, the Pin 0x1b is Headphone-Mic, so we should assign
ALC269_FIXUP_DELL4_MIC_NO_PRESENCE rather than
ALC225_FIXUP_DELL1_MIC_NO_PRESENCE to it. And this change is suggested
by Kailang of Realtek and is verified on the machine.
Fixes: 3f2f7c553d07 ("ALSA: hda - Fix headset mic detection problem for two Dell machines") Cc: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by: Hui Wang <hui.wang@canonical.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DELL4_MIC_NO_PRESENCE model.
Add the pin configuration value of this machine into the pin_quirk
table to make DELL4_MIC_NO_PRESENCE apply to this machine.
The altsetting sanity check in set_sync_ep_implicit_fb_quirk() was
checking for there to be at least one altsetting but then went on to
access the second one, which may not exist.
This could lead to random slab data being used to initialise the sync
endpoint in snd_usb_add_endpoint().
Fixes: c75a8a7ae565 ("ALSA: snd-usb: add support for implicit feedback") Fixes: ca10a7ebdff1 ("ALSA: usb-audio: FT C400 sync playback EP to capture EP") Fixes: 5e35dc0338d8 ("ALSA: usb-audio: add implicit fb quirk for Behringer UFX1204") Fixes: 17f08b0d9aaf ("ALSA: usb-audio: add implicit fb quirk for Axe-Fx II") Fixes: 103e9625647a ("ALSA: usb-audio: simplify set_sync_ep_implicit_fb_quirk") Cc: stable <stable@vger.kernel.org> # 3.5 Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20200114083953.1106-1-johan@kernel.org Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CA0132 has the delayed HP jack detection code that is invoked from the
unsol handler, but it does a few weird things: it contains the cancel
of a work inside the work handler, and yet it misses the cancel-sync
call at (runtime-)suspend. This patch addresses those issues.
If kobject_init_and_add() fails, pci_slot_release() is called to delete
slot->list from parent->slots. But slot->list hasn't been initialized
yet, so we dereference a NULL pointer:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
CPU: 10 PID: 1 Comm: swapper/0 Not tainted 4.4.240 #197
task: ffffeb398a45ef10 task.stack: ffffeb398a470000
PC is at __list_del_entry_valid+0x5c/0xb0
LR is at pci_slot_release+0x84/0xe4
...
__list_del_entry_valid+0x5c/0xb0
pci_slot_release+0x84/0xe4
kobject_put+0x184/0x1c4
pci_create_slot+0x17c/0x1b4
__pci_hp_initialize+0x68/0xa4
pciehp_probe+0x1a4/0x2fc
pcie_port_probe_service+0x58/0x84
driver_probe_device+0x320/0x470
Initialize slot->list before calling kobject_init_and_add() to avoid this.
'xenbus_backend' watches 'state' of devices, which is writable by
guests. Hence, if guests intensively updates it, dom0 will have lots of
pending events that exhausting memory of dom0. In other words, guests
can trigger dom0 memory pressure. This is known as XSA-349. However,
the watch callback of it, 'frontend_changed()', reads only 'state', so
doesn't need to have the pending events.
To avoid the problem, this commit disallows pending watch messages for
'xenbus_backend' using the 'will_handle()' watch callback.
This commit adds a counter of pending messages for each watch in the
struct. It is used to skip unnecessary pending messages lookup in
'unregister_xenbus_watch()'. It could also be used in 'will_handle'
callback.
Some code does not directly make 'xenbus_watch' object and call
'register_xenbus_watch()' but use 'xenbus_watch_path()' instead. This
commit adds support of 'will_handle' callback in the
'xenbus_watch_path()' and it's wrapper, 'xenbus_watch_pathfmt()'.
If handling logics of watch events are slower than the events enqueue
logic and the events can be created from the guests, the guests could
trigger memory pressure by intensively inducing the events, because it
will create a huge number of pending events that exhausting the memory.
Fortunately, some watch events could be ignored, depending on its
handler callback. For example, if the callback has interest in only one
single path, the watch wouldn't want multiple pending events. Or, some
watches could ignore events to same path.
To let such watches to volutarily help avoiding the memory pressure
situation, this commit introduces new watch callback, 'will_handle'. If
it is not NULL, it will be called for each new event just before
enqueuing it. Then, if the callback returns false, the event will be
discarded. No watch is using the callback for now, though.
Whilst this is another case of the issue Lars reported with
an array of elements of smaller than 8 bytes being passed
to iio_push_to_buffers_with_timestamp(), the solution here is
a bit different from the other cases and relies on __aligned
working on the stack (true since 4.6?)
This one is unusual. We have to do an explicit memset() each time
as we are reading 3 bytes into a potential 4 byte channel which
may sometimes be a 2 byte channel depending on what is enabled.
As such, moving the buffer to the heap in the iio_priv structure
doesn't save us much. We can't use a nice explicit structure
on the stack either as the data channels have different storage
sizes and are all separately controlled.
Fixes: cc26ad455f57 ("iio: Add Freescale MPL3115A2 pressure / temperature sensor driver") Reported-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Reviewed-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Cc: Peter Meerwald <pmeerw@pmeerw.net> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200920112742.170751-7-jic23@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the missing clk_disable_unprepare() of info->pclk
before return from rockchip_saradc_resume in the error
handling case when fails to prepare and enable info->clk.
Suggested-by: Robin Murphy <robin.murphy@arm.com> Fixes: 44d6f2ef94f9 ("iio: adc: add driver for Rockchip saradc") Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20201103120743.110662-1-miaoqinglang@huawei.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:
Such a partition list cannot be parsed and thus the device fails to boot.
Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.
Fixes: eb13fa022741 ("mtd: parser: cmdline: Support MTD names containing one or more colons") Cc: stable@vger.kernel.org Cc: Ron Minnich <rminnich@google.com> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/20201124062506.185392-1-sven@narfation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the calls to devm_clk_get(), devm_spi_register_master() or
clk_prepare_enable() fail on probe of the Mikrotik RB4xx SPI driver,
the spi_master struct is erroneously not freed.
Fix by switching over to the new devm_spi_alloc_master() helper.
Bounds checking tools can flag a bug in dbAdjTree() for an array index
out of bounds in dmt_stree. Since dmt_stree can refer to the stree in
both structures dmaptree and dmapctl, use the larger array to eliminate
the false positive.
The log of this problem is:
jffs2: Error garbage collecting node at 0x***!
jffs2: No space for garbage collection. Aborting GC thread
This is because GC believe that it do nothing, so it abort.
After going over the image of jffs2, I find a scene that
can trigger this problem stably.
The scene is: there is a normal dirent node at summary-area,
but abnormal at corresponding not-summary-area with error
name_crc.
The reason that GC exit abnormally is because it find that
abnormal dirent node to GC, but when it goes to function
jffs2_add_fd_to_list, it cannot meet the condition listed
below:
if ((*prev)->nhash == new->nhash && !strcmp((*prev)->name, new->name))
So no node is marked obsolete, statistical information of
erase_block do not change, which cause GC exit abnormally.
The root cause of this problem is: we do not check the
name_crc of the abnormal dirent node with summary is enabled.
Noticed that in function jffs2_scan_dirent_node, we use
function jffs2_scan_dirty_space to deal with the dirent
node with error name_crc. So this patch add a checking
code in function read_direntry to ensure the correctness
of dirent node. If checked failed, the dirent node will
be marked obsolete so GC will pass this node and this
problem will be fixed.
Cc: <stable@vger.kernel.org> Signed-off-by: Zhe Li <lizhe67@huawei.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A NULL pointer dereference may occur in __ceph_remove_cap with some of the
callbacks used in ceph_iterate_session_caps, namely trim_caps_cb and
remove_session_caps_cb. Those callers hold the session->s_mutex, so they
are prevented from concurrent execution, but ceph_evict_inode does not.
Since the callers of this function hold the i_ceph_lock, the fix is simply
a matter of returning immediately if caps->ci is NULL.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/43272 Suggested-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Luis Henriques <lhenriques@suse.de> Reviewed-by: Jeff Layton <jlayton@kernel.org> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When freeing metadata, we will create an ext4_free_data and
insert it into the pending free list. After the current
transaction is committed, the object will be freed.
ext4_mb_free_metadata() will check whether the area to be freed
overlaps with the pending free list. If true, return directly. At this
time, ext4_free_data is leaked. Fortunately, the probability of this
problem is small, since it only occurs if the file system is corrupted
such that a block is claimed by more one inode and those inodes are
deleted within a single jbd2 transaction.
Some of the self tests create a test inode, setup some extents and then do
calls to btrfs_get_extent() to test that the corresponding extent maps
exist and are correct. However btrfs_get_extent(), since the 5.2 merge
window, now errors out when it finds a regular or prealloc extent for an
inode that does not correspond to a regular file (its ->i_mode is not
S_IFREG). This causes the self tests to fail sometimes, specially when
KASAN, slub_debug and page poisoning are enabled:
$ modprobe btrfs
modprobe: ERROR: could not insert 'btrfs': Invalid argument
This happens because the test inodes are created without ever initializing
the i_mode field of the inode, and neither VFS's new_inode() nor the btrfs
callback btrfs_alloc_inode() initialize the i_mode. Initialization of the
i_mode is done through the various callbacks used by the VFS to create
new inodes (regular files, directories, symlinks, tmpfiles, etc), which
all call btrfs_new_inode() which in turn calls inode_init_owner(), which
sets the inode's i_mode. Since the tests only uses new_inode() to create
the test inodes, the i_mode was never initialized.
This always happens on a VM I used with kasan, slub_debug and many other
debug facilities enabled. It also happened to someone who reported this
on bugzilla (on a 5.3-rc).
Fix this by setting i_mode to S_IFREG at btrfs_new_test_inode().
In commit ac0b4145d662 ("btrfs: scrub: Don't use inode pages for device
replace") we removed the branch of copy_nocow_pages() to avoid
corruption for compressed nodatasum extents.
However above commit only solves the problem in scrub_extent(), if
during scrub_pages() we failed to read some pages,
sctx->no_io_error_seen will be non-zero and we go to fixup function
scrub_handle_errored_block().
In scrub_handle_errored_block(), for sctx without csum (no matter if
we're doing replace or scrub) we go to scrub_fixup_nodatasum() routine,
which does the similar thing with copy_nocow_pages(), but does it
without the extra check in copy_nocow_pages() routine.
So for test cases like btrfs/100, where we emulate read errors during
replace/scrub, we could corrupt compressed extent data again.
This patch will fix it just by avoiding any "optimization" for
nodatasum, just falls back to the normal fixup routine by try read from
any good copy.
This also solves WARN_ON() or dead lock caused by lame backref iteration
in scrub_fixup_nodatasum() routine.
The deadlock or WARN_ON() won't be triggered before commit ac0b4145d662
("btrfs: scrub: Don't use inode pages for device replace") since
copy_nocow_pages() have better locking and extra check for data extent,
and it's already doing the fixup work by try to read data from any good
copy, so it won't go scrub_fixup_nodatasum() anyway.
This patch disables the faulty code and will be removed completely in a
followup patch.
Fixes: ac0b4145d662 ("btrfs: scrub: Don't use inode pages for device replace") Signed-off-by: Qu Wenruo <wqu@suse.com> Signed-off-by: David Sterba <dsterba@suse.com>
[sudip: adjust context] Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ff3d27a048d9 ("btrfs: qgroup: Finish rescan when hit the last leaf
of extent tree") added a new exit for rescan finish.
However after finishing quota rescan, we set
fs_info->qgroup_rescan_progress to (u64)-1 before we exit through the
original exit path.
While we missed that assignment of (u64)-1 in the new exit path.
The end result is, the quota status item doesn't have the same value.
(-1 vs the last bytenr + 1)
Although it doesn't affect quota accounting, it's still better to keep
the original behavior.
Reported-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com> Fixes: ff3d27a048d9 ("btrfs: qgroup: Finish rescan when hit the last leaf of extent tree") Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: Misono Tomohiro <misono.tomohiro@jp.fujitsu.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver did not update its view of the available device buffer space
until write() was called in task context. This meant that write_room()
would return 0 even after the device had sent a write-unthrottle
notification, something which could lead to blocked writers not being
woken up (e.g. when using OPOST).
Note that we must also request an unthrottle notification is case a
write() request fills the device buffer exactly.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable <stable@vger.kernel.org> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver's transmit-unthrottle work was never flushed on disconnect,
something which could lead to the driver port data being freed while the
unthrottle work is still scheduled.
Fix this by cancelling the unthrottle work when shutting down the port.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver's deferred write wakeup was never flushed on disconnect,
something which could lead to the driver port data being freed while the
wakeup work is still scheduled.
Fix this by using the usb-serial write wakeup which gets cancelled
properly on disconnect.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to clear the write-busy flag also in case no new data was
submitted due to lack of device buffer space so that writing is
resumed once space again becomes available.
Fixes: 507ca9bc0476 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.") Cc: stable <stable@vger.kernel.org> # 2.6.13 Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The write() callback can be called in interrupt context (e.g. when used
as a console) so interrupts must be disabled while holding the port lock
to prevent a possible deadlock.
Fixes: e81ee637e4ae ("usb-serial: possible irq lock inversion (PPP vs. usb/serial)") Fixes: 507ca9bc0476 ("[PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.") Cc: stable <stable@vger.kernel.org> # 2.6.19 Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c528fcb116e6 ("USB: serial: keyspan_pda: fix receive sanity
checks") broke write-unthrottle handling by dropping well-formed
unthrottle-interrupt packets which are precisely two bytes long. This
could lead to blocked writers not being woken up when buffer space again
becomes available.
Instead, stop unconditionally printing the third byte which is
(presumably) only valid on modem-line changes.
The parallel-port restore operations is called when a driver claims the
port and is supposed to restore the provided state (e.g. saved when
releasing the port).
Fixes: b69578df7e98 ("USB: usbserial: mos7720: add support for parallel port on moschip 7715") Cc: stable <stable@vger.kernel.org> # 2.6.35 Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Perf event attritube supports exclude_kernel flag to avoid
sampling/profiling in supervisor state (kernel). Based on this event
attr flag, Monitor Mode Control Register bit is set to freeze on
supervisor state. But sometimes (due to hardware limitation), Sampled
Instruction Address Register (SIAR) locks on to kernel address even
when freeze on supervisor is set. Patch here adds a check to drop
those samples.
I have had reports from two different people that attempts to read the
analog input channels of the MF624 board fail with an `ETIMEDOUT` error.
After triggering the conversion, the code calls `comedi_timeout()` with
`mf6x4_ai_eoc()` as the callback function to check if the conversion is
complete. The callback returns 0 if complete or `-EBUSY` if not yet
complete. `comedi_timeout()` returns `-ETIMEDOUT` if it has not
completed within a timeout period which is propagated as an error to the
user application.
The existing code considers the conversion to be complete when the EOLC
bit is high. However, according to the user manuals for the MF624 and
MF634 boards, this test is incorrect because EOLC is an active low
signal that goes high when the conversion is triggered, and goes low
when the conversion is complete. Fix the problem by inverting the test
of the EOLC bit state.
In dasd_alias_disconnect_device_from_lcu the device is removed from any
list on the LCU. Afterwards the LCU is removed from the lcu list if it
does not contain devices any longer.
The lcu->lock protects the lcu from parallel updates. But to cancel all
workers and wait for completion the lcu->lock has to be unlocked.
If two devices are removed in parallel and both are removed from the LCU
the first device that takes the lcu->lock again will delete the LCU because
it is already empty but the second device also tries to free the LCU which
leads to a list corruption of the lcu list.
Fix by removing the device right before the lcu is checked without
unlocking the lcu->lock in between.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1") Cc: stable@vger.kernel.org Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dasd_alias_add_device() moves devices to the active_devices list in case
of a scheduled LCU update regardless if they have previously been in a
pavgroup or not.
Example: device A and B are in the same pavgroup.
Device A has already been in a pavgroup and the private->pavgroup pointer
is set and points to a valid pavgroup. While going through dasd_add_device
it is moved from the pavgroup to the active_devices list.
In parallel device B might be removed from the same pavgroup in
remove_device_from_lcu() which in turn checks if the group is empty
and deletes it accordingly because device A has already been removed from
there.
When now device A enters remove_device_from_lcu() it is tried to remove it
from the pavgroup again because the pavgroup pointer is still set and again
the empty group will be cleaned up which leads to a list corruption.
Fix by setting private->pavgroup to NULL in dasd_add_device.
If the device has been the last device on the pavgroup an empty pavgroup
remains but this will be cleaned up by the scheduled lcu_update which
iterates over all existing pavgroups.
Fixes: 8e09f21574ea ("[S390] dasd: add hyper PAV support to DASD device driver, part 1") Cc: stable@vger.kernel.org Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few places that call round{up|down}_pow_of_two() with the
value zero, and this causes undefined behavior warnings. Avoid
calling those macros if such a nonsense value is passed; it's a minor
optimization as well, as we handle it as either an error or a value to
be skipped, instead.
Recently we met a touchscreen problem on some Thinkpad machines, the
touchscreen driver (i2c-hid) is not loaded and the touchscreen can't
work.
An i2c ACPI device with the name WACF2200 is defined in the BIOS, with
the current rule in matching_id(), this device will be regarded as
a PNP device since there is WACFXXX in the acpi_pnp_device_ids[] and
this PNP device is attached to the acpi device as the 1st
physical_node, this will make the i2c bus match fail when i2c bus
calls acpi_companion_match() to match the acpi_id_table in the i2c-hid
driver.
WACF2200 is an i2c device instead of a PNP device, after adding the
string length comparing, the matching_id() will return false when
matching WACF2200 and WACFXXX, and it is reasonable to compare the
string length when matching two IDs.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Hui Wang <hui.wang@canonical.com> Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switching this function to AE_CTRL_TERMINATE broke the documented
behaviour of acpi_dev_get_resources() - AE_CTRL_TERMINATE does not, in
fact, terminate the resource walk because acpi_walk_resource_buffer()
ignores it (specifically converting it to AE_OK), referring to that
value as "an OK termination by the user function". This means that
acpi_dev_get_resources() does not abort processing when the preproc
function returns a negative value.
Signed-off-by: Daniel Scally <djrscally@gmail.com> Cc: 3.10+ <stable@vger.kernel.org> # 3.10+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the call to spi_register_master() fails on probe of the NetUP
Universal DVB driver, the spi_master struct is erroneously not freed.
Likewise, if spi_new_device() fails, the spi_controller struct is
not unregistered. Plug the leaks.
While at it, fix an ordering issue in netup_spi_release() wherein
spi_unregister_master() is called after fiddling with the IRQ control
register. The correct order is to call spi_unregister_master() *before*
this teardown step because bus accesses may still be ongoing until that
function returns.
If a user holds a button down on a remote, then no ir idle interrupt will
be generated until the user releases the button, depending on how quickly
the remote repeats. No IR is processed until that point, which means that
holding down a button may not do anything.
This also resolves an issue on a Cubieboard 1 where the IR receiver is
picking up ambient infrared as IR and spews out endless
"rc rc0: IR event FIFO is full!" messages unless you choose to live in
the dark.
Cc: stable@vger.kernel.org Tested-by: Hans Verkuil <hverkuil@xs4all.nl> Acked-by: Maxime Ripard <mripard@kernel.org> Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gspca driver leaks memory when a probe fails. gspca_dev_probe2()
calls v4l2_device_register(), which takes a reference to the
underlying device node (in this case, a USB interface). But the
failure pathway neglects to call v4l2_device_unregister(), the routine
responsible for dropping this reference. Consequently the memory for
the USB interface and its device never gets released.
To let userspace know what 'scancodes' should be used in EVIOCGKEYCODE
and EVIOCSKEYCODE ioctls, we should send EV_MSC/MSC_SCAN events in
addition to EV_KEY/KEY_* events. The driver already declared MSC_SCAN
capability, so it is only matter of actually sending the events.
When using 'perf record's option '-I' or '--user-regs=' along with
argument '?' to list available register names, memory of variable 'os'
allocated by strdup() needs to be released before __parse_regs()
returns, otherwise memory leak will occur.
Fixes: bcc84ec65ad1 ("perf record: Add ability to name registers to record") Signed-off-by: Zheng Zengkai <zhengzengkai@huawei.com> Acked-by: Jiri Olsa <jolsa@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Li Bin <huawei.libin@huawei.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Link: https://lore.kernel.org/r/20200703093344.189450-1-zhengzengkai@huawei.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ndo_start_xmit() method must not attempt to free the skb to transmit
when returning NETDEV_TX_BUSY. Therefore, make sure the
korina_send_packet() function returns NETDEV_TX_OK when it frees a packet.
Fixes: ef11291bcd5f ("Add support the Korina (IDT RC32434) Ethernet MAC") Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20201214220952.19935-1-vincent.stehle@laposte.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is an unescaped left brace in a regex in OPEN_BRACE check. This
throws a runtime error when checkpatch is run with --fix flag and the
OPEN_BRACE check is executed.
Fix it by escaping the left brace.
Link: https://lkml.kernel.org/r/20201115202928.81955-1-dwaipayanray1@gmail.com Fixes: 8d1824780f2f ("checkpatch: add --fix option for a couple OPEN_BRACE misuses") Signed-off-by: Dwaipayan Ray <dwaipayanray1@gmail.com> Acked-by: Joe Perches <joe@perches.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
xterm serial channel was leaking a fd used in setting up the
port helper
This bug is prehistoric - it predates switching to git. The "fixes"
header here is really just to mark all the versions we would like this to
apply to which is "Anything from the Cretaceous period onwards".
No dinosaurs were harmed in fixing this bug.
Fixes: b40997b872cd ("um: drivers/xterm.c: fix a file descriptor leak") Signed-off-by: Anton Ivanov <anton.ivanov@cambridgegreys.com> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error handling frees "ctl" but it's still on the "dsp->ctl_list"
list so that could result in a use after free. Remove it from the list
before returning.
Fixes: 2323736dca72 ("ASoC: wm_adsp: Add basic support for rev 1 firmware file format") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Link: https://lore.kernel.org/r/X9B0keV/02wrx9Xs@mwanda Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The platform device driver name is "max77693-muic", so advertise it
properly in the modalias string. This fixes automated module loading when
this driver is compiled as a module.
Fixes: db1b9037424b ("extcon: MAX77693: Add extcon-max77693 driver to support Maxim MAX77693 MUIC device") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix to restore BTF if single-stepping causes a page fault and
it is cancelled.
Usually the BTF flag was restored when the single stepping is done
(in resume_execution()). However, if a page fault happens on the
single stepping instruction, the fault handler is invoked and
the single stepping is cancelled. Thus, the BTF flag is not
restored.
The pm_runtime_enable will decrement the power disable depth. Imbalance
depth will resulted in enabling runtime PM of device fails later. Thus
a pairing decrement must be needed on the error handling path to keep it
balanced.
This never works because there is no way to supply a valid stream id
using this interface, and H_VASI_STATE is called with a stream id of
zero. So this call path is useless at best.
2. When a stream id is written to /sys/devices/system/power/hibernate.
pseries_suspend_begin() is polled directly from store_hibernate()
until the stream is in the "Suspending" state (i.e. the platform is
ready for the OS to suspend execution):
3. When a stream id is written to /sys/devices/system/power/hibernate
(continued). After #2, pseries_suspend_begin() is called once again
from the pm core:
Building with W=2 prints a number of warnings for one function that
has a pointer type mismatch:
linux/seq_buf.h: In function 'seq_buf_init':
linux/seq_buf.h:35:12: warning: pointer targets in assignment from 'unsigned char *' to 'char *' differ in signedness [-Wpointer-sign]
Change the type in the function prototype according to the type in
the structure.
Link: https://lkml.kernel.org/r/20201026161108.3707783-1-arnd@kernel.org Fixes: 9a7777935c34 ("tracing: Convert seq_buf fields to be like seq_file fields") Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver did not return an error in the case where
pm8001_configure_phy_settings() failed.
Use rc to store the return value of pm8001_configure_phy_settings().
Link: https://lore.kernel.org/r/20201205115551.2079471-1-zhangqilong3@huawei.com Fixes: 279094079a44 ("[SCSI] pm80xx: Phy settings support for motherboard controller.") Acked-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this cpufreq driver when it is
compiled as an external module.
ARM virtual counter supports event stream, it can only trigger an event
when the trigger bit (the value of CNTKCTL_EL1.EVNTI) of CNTVCT_EL0 changes,
so the actual period of event stream is 2^(cntkctl_evnti + 1). For example,
when the trigger bit is 0, then virtual counter trigger an event for every
two cycles.
While we're at it, rework the way we compute the trigger bit position
by making it more obvious that when bits [n:n-1] are both set (with n
being the most significant bit), we pick bit (n + 1).
Fixes: 037f637767a8 ("drivers: clocksource: add support for ARM architected timer event stream") Suggested-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com> Acked-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20201204073126.6920-3-zhukeqian1@huawei.com Signed-off-by: Sasha Levin <sashal@kernel.org>
jz4740_i2s_set_sysclk() does not check the return values of clk_get(),
while the file dereferences the pointers in clk_put().
Add the missed checks to fix it.
if of_find_device_by_node() succeed, pinctrl_falcon_probe() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
The "a->index" value comes from the user via the ioctl. The problem is
that the shift can wrap resulting in setting "mxb->cur_audinput" to an
invalid value, which later results in an array overflow.
nfsiod is currently a concurrency-managed workqueue (CMWQ).
This means that workitems scheduled to nfsiod on a given CPU are queued
behind all other work items queued on any CMWQ on the same CPU. This
can introduce unexpected latency.
Occaionally nfsiod can even cause excessive latency. If the work item
to complete a CLOSE request calls the final iput() on an inode, the
address_space of that inode will be dismantled. This takes time
proportional to the number of in-memory pages, which on a large host
working on large files (e.g.. 5TB), can be a large number of pages
resulting in a noticable number of seconds.
We can avoid these latency problems by switching nfsiod to WQ_UNBOUND.
This causes each concurrent work item to gets a dedicated thread which
can be scheduled to an idle CPU.
There is precedent for this as several other filesystems use WQ_UNBOUND
workqueue for handling various async events.
Signed-off-by: NeilBrown <neilb@suse.de> Fixes: ada609ee2ac2 ("workqueue: use WQ_MEM_RECLAIM instead of WQ_RESCUER") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
NLM uses an interval-based rebinding, i.e. it clears the transport's
binding under certain conditions if more than 60 seconds have elapsed
since the connection was last bound.
This rebinding is not necessary for an autobind RPC client over a
connection-oriented protocol like TCP.
It can also cause problems: it is possible for nlm_bind_host() to clear
XPRT_BOUND whilst a connection worker is in the middle of trying to
reconnect, after it had already been checked in xprt_connect().
When the connection worker notices that XPRT_BOUND has been cleared
under it, in xs_tcp_finish_connecting(), that results in:
xs_tcp_setup_socket: connect returned unhandled error -107
Worse, it's possible that the two can get into lockstep, resulting in
the same behaviour repeated indefinitely, with the above error every
300 seconds, without ever recovering, and the connection never being
established. This has been seen in practice, with a large number of NLM
client tasks, following a server restart.
The existing callers of nlm_bind_host & nlm_rebind_host should not need
to force the rebind, for TCP, so restrict the interval-based rebinding
to UDP only.
For TCP, we will still rebind when needed, e.g. on timeout, and connection
error (including closure), since connection-related errors on an existing
connection, ECONNREFUSED when trying to connect, and rpc_check_timeout(),
already unconditionally clear XPRT_BOUND.
To avoid having to add the fix, and explanation, to both nlm_bind_host()
and nlm_rebind_host(), remove the duplicate code from the former, and
have it call the latter.
Drop the dprintk, which adds no value over a trace.
Signed-off-by: Calum Mackay <calum.mackay@oracle.com> Fixes: 35f5a422ce1a ("SUNRPC: new interface to force an RPC rebind") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the client will always ask for security_labels if the server
returns that it supports that feature regardless of any LSM modules
(such as Selinux) enforcing security policy. This adds performance
penalty to the READDIR operation.
Client adjusts superblock's support of the security_label based on
the server's support but also current client's configuration of the
LSM modules. Thus, prior to using the default bitmask in READDIR,
this patch checks the server's capabilities and then instructs
READDIR to remove FATTR4_WORD2_SECURITY_LABEL from the bitmask.
v5: fixing silly mistakes of the rushed v4
v4: simplifying logic
v3: changing label's initialization per Ondrej's comment
v2: dropping selinux hook and using the sb cap.
Suggested-by: Ondrej Mosnacek <omosnace@redhat.com> Suggested-by: Scott Mayhew <smayhew@redhat.com> Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Fixes: 2b0143b5c986 ("VFS: normal filesystems (and lustre): d_inode() annotations") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ezusb_xmit() allocates a context which is leaked if
orinoco_process_xmit_skb() returns an error.
Move ezusb_alloc_ctx() after the invocation of
orinoco_process_xmit_skb() because the context is not needed so early.
ezusb_access_ltv() will cleanup the context in case of an error.
Fixes: bac6fafd4d6a0 ("orinoco: refactor xmit path") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20201113212252.2243570-2-bigeasy@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
The pincontrol node is needed for USB Host since Linux v5.7-rc1. Without
it the driver probes but VBus is not powered because of wrong pincontrol
configuration.
projects / linux-stable / log