Calling acpi_thermal_check() from acpi_thermal_notify() directly
is problematic if _TMP triggers Notify () on the thermal zone for
which it has been evaluated (which happens on some systems), because
it causes a new acpi_thermal_notify() invocation to be queued up
every time and if that takes place too often, an indefinite number of
pending work items may accumulate in kacpi_notify_wq over time.
Besides, it is not really useful to queue up a new invocation of
acpi_thermal_check() if one of them is pending already.
For these reasons, rework acpi_thermal_notify() to queue up a thermal
check instead of calling acpi_thermal_check() directly and only allow
one thermal check to be pending at a time. Moreover, only allow one
acpi_thermal_check_fn() instance at a time to run
thermal_zone_device_update() for one thermal zone and make it return
early if it sees other instances running for the same thermal zone.
While at it, fold acpi_thermal_check() into acpi_thermal_check_fn(),
as it is only called from there after the other changes made here.
[This issue appears to have been exposed by commit 6d25be5782e4
("sched/core, workqueues: Distangle worker accounting from rq
lock"), but it is unclear why it was not visible earlier.]
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208877 Reported-by: Stephen Berman <stephen.berman@gmx.net> Diagnosed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: Stephen Berman <stephen.berman@gmx.net> Cc: All applicable <stable@vger.kernel.org>
[bigeasy: Backported to v4.4.y, use atomic_t instead of refcount_t] Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jan Kiszka reported that the x2apic_wrmsr_fence() function uses a plain
MFENCE while the Intel SDM (10.12.3 MSR Access in x2APIC Mode) calls for
MFENCE; LFENCE.
Short summary: we have special MSRs that have weaker ordering than all
the rest. Add fencing consistent with current SDM recommendations.
This is not known to cause any issues in practice, only in theory.
Longer story below:
The reason the kernel uses a different semantic is that the SDM changed
(roughly in late 2017). The SDM changed because folks at Intel were
auditing all of the recommended fences in the SDM and realized that the
x2apic fences were insufficient.
Why was the pain MFENCE judged insufficient?
WRMSR itself is normally a serializing instruction. No fences are needed
because the instruction itself serializes everything.
But, there are explicit exceptions for this serializing behavior written
into the WRMSR instruction documentation for two classes of MSRs:
IA32_TSC_DEADLINE and the X2APIC MSRs.
Back to x2apic: WRMSR is *not* serializing in this specific case.
But why is MFENCE insufficient? MFENCE makes writes visible, but
only affects load/store instructions. WRMSR is unfortunately not a
load/store instruction and is unaffected by MFENCE. This means that a
non-serializing WRMSR could be reordered by the CPU to execute before
the writes made visible by the MFENCE have even occurred in the first
place.
This means that an x2apic IPI could theoretically be triggered before
there is any (visible) data to process.
Does this affect anything in practice? I honestly don't know. It seems
quite possible that by the time an interrupt gets to consume the (not
yet) MFENCE'd data, it has become visible, mostly by accident.
To be safe, add the SDM-recommended fences for all x2apic WRMSRs.
This also leaves open the question of the _other_ weakly-ordered WRMSR:
MSR_IA32_TSC_DEADLINE. While it has the same ordering architecture as
the x2APIC MSRs, it seems substantially less likely to be a problem in
practice. While writes to the in-memory Local Vector Table (LVT) might
theoretically be reordered with respect to a weakly-ordered WRMSR like
TSC_DEADLINE, the SDM has this to say:
In x2APIC mode, the WRMSR instruction is used to write to the LVT
entry. The processor ensures the ordering of this write and any
subsequent WRMSR to the deadline; no fencing is required.
But, that might still leave xAPIC exposed. The safest thing to do for
now is to add the extra, recommended LFENCE.
[ bp: Massage commit message, fix typos, drop accidentally added
newline to tools/arch/x86/include/asm/barrier.h. ]
Reported-by: Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Cc: <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20200305174708.F77040DD@viggo.jf.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With retpolines disabled, some configurations of GCC, and specifically
the GCC versions 9 and 10 in Ubuntu will add Intel CET instrumentation
to the kernel by default. That breaks certain tracing scenarios by
adding a superfluous ENDBR64 instruction before the fentry call, for
functions which can be called indirectly.
CET instrumentation isn't currently necessary in the kernel, as CET is
only supported in user space. Disable it unconditionally and move it
into the x86's Makefile as CET/CFI... enablement should be a per-arch
decision anyway.
[ bp: Massage and extend commit message. ]
Fixes: 29be86d7f9cb ("kbuild: add -fcf-protection=none when using retpoline flags") Reported-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Nikolay Borisov <nborisov@suse.com> Tested-by: Nikolay Borisov <nborisov@suse.com> Cc: <stable@vger.kernel.org> Cc: Seth Forshee <seth.forshee@canonical.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Link: https://lkml.kernel.org/r/20210128215219.6kct3h2eiustncws@treble Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The page_huge_active() can be called from scan_movable_pages() which do
not hold a reference count to the HugeTLB page. So when we call
page_huge_active() from scan_movable_pages(), the HugeTLB page can be
freed parallel. Then we will trigger a BUG_ON which is in the
page_huge_active() when CONFIG_DEBUG_VM is enabled. Just remove the
VM_BUG_ON_PAGE.
Link: https://lkml.kernel.org/r/20210115124942.46403-6-songmuchun@bytedance.com Fixes: 7e1f049efb86 ("mm: hugetlb: cleanup using paeg_huge_active()") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: David Hildenbrand <david@redhat.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we isolate a HugeTLB page on CPU0. Meanwhile, we free it to the
buddy allocator on CPU1. Then, we can trigger a BUG_ON on CPU0, because
it is already freed to the buddy allocator.
Link: https://lkml.kernel.org/r/20210115124942.46403-5-songmuchun@bytedance.com Fixes: c8721bbbdd36 ("mm: memory-hotplug: enable memory hotplug to handle hugepage") Signed-off-by: Muchun Song <songmuchun@bytedance.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: David Hildenbrand <david@redhat.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a new hugetlb page is allocated during fallocate it will not be
marked as active (set_page_huge_active) which will result in a later
isolate_huge_page failure when the page migration code would like to
move that page. Such a failure would be unexpected and wrong.
Only export set_page_huge_active, just leave clear_page_huge_active as
static. Because there are no external users.
Link: https://lkml.kernel.org/r/20210115124942.46403-3-songmuchun@bytedance.com Fixes: 70c3547e36f5 (hugetlbfs: add hugetlbfs_fallocate()) Signed-off-by: Muchun Song <songmuchun@bytedance.com> Acked-by: Michal Hocko <mhocko@suse.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Cc: David Hildenbrand <david@redhat.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building with gcc 4.9.2 reveals a latent bug in the PCI accessors
for Footbridge platforms, which causes a fatal alignment fault
while accessing IO memory. Fix this by making the assembly volatile.
Cc: stable@vger.kernel.org Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assuming
- //HOST/a is mounted on /mnt
- //HOST/b is mounted on /mnt/b
On a slow connection, running 'df' and killing it while it's
processing /mnt/b can make cifs_get_inode_info() returns -ERESTARTSYS.
This triggers the following chain of events:
=> the dentry revalidation fail
=> dentry is put and released
=> superblock associated with the dentry is put
=> /mnt/b is unmounted
This patch makes cifs_d_revalidate() return the error instead of 0
(invalid) when cifs_revalidate_dentry() fails, except for ENOENT (file
deleted) and ESTALE (file recreated).
Signed-off-by: Aurelien Aptel <aaptel@suse.com> Suggested-by: Shyam Prasad N <nspmangalore@gmail.com> Reviewed-by: Shyam Prasad N <nspmangalore@gmail.com> CC: stable@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Our system encountered a re-init error when re-registering same kretprobe,
where the kretprobe_instance in rp->free_instances is illegally accessed
after re-init.
Implementation to avoid re-registration has been introduced for kprobe
before, but lags for register_kretprobe(). We must check if kprobe has
been re-registered before re-initializing kretprobe, otherwise it will
destroy the data struct of kretprobe registered, which can lead to memory
leak, system crash, also some unexpected behaviors.
We use check_kprobe_rereg() to check if kprobe has been re-registered
before running register_kretprobe()'s body, for giving a warning message
and terminate registration process.
Link: https://lkml.kernel.org/r/20210128124427.2031088-1-bobo.shaobowang@huawei.com Cc: stable@vger.kernel.org Fixes: 1f0ab40976460 ("kprobes: Prevent re-registration of the same kprobe")
[ The above commit should have been done for kretprobes too ] Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Acked-by: Ananth N Mavinakayanahalli <ananth@linux.ibm.com> Acked-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com> Signed-off-by: Cheng Jian <cj.chengjian@huawei.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the driver uses .sta_add, station entries are only uploaded after the sta
is in assoc state. Fix early station rate table updates by deferring them
until the sta has been uploaded.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20210201083324.3134-1-nbd@nbd.name
[use rcu_access_pointer() instead since we won't dereference here] Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc2_hsotg_process_req_status uses ep_from_windex() to retrieve
the endpoint for the index provided in the wIndex request param.
In a test-case with a rndis gadget running and sending a malformed
packet to it like:
dev.ctrl_transfer(
0x82, # bmRequestType
0x00, # bRequest
0x0000, # wValue
0x0001, # wIndex
0x00 # wLength
)
it is possible to cause a crash:
This happens because ep_from_windex wants to compare the endpoint
direction even if index_to_ep() didn't return an endpoint due to
the direction not matching.
The fix is easy insofar that the actual direction check is already
happening when calling index_to_ep() which will return NULL if there
is no endpoint for the targeted direction, so the offending check
can go away completely.
Some devices, such as the Winbond Electronics Corp. Virtual Com Port
(Vendor=0416, ProdId=5011), lockup when usb_set_interface() or
usb_clear_halt() are called. This device has only a single
altsetting, so it should not be necessary to call usb_set_interface().
Acked-by: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Jeremy Figgins <kernel@jeremyfiggins.com> Link: https://lore.kernel.org/r/YAy9kJhM/rG8EQXC@watson Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kernel/elfcore.c only contains weak symbols, which triggers a bug with
clang in combination with recordmcount:
Cannot find symbol for section 2: .text.
kernel/elfcore.o: failed
Move the empty stubs into linux/elfcore.h as inline functions. As only
two architectures use these, just use the architecture specific Kconfig
symbols to key off the declaration.
CONFIG_MIPS32_N32=y but CONFIG_BINFMT_ELF disabled results in the
following linker errors:
arch/mips/built-in.o: In function `elf_core_dump':
binfmt_elfn32.c:(.text+0x23dbc): undefined reference to `elf_core_extra_phdrs'
binfmt_elfn32.c:(.text+0x246e4): undefined reference to `elf_core_extra_data_size'
binfmt_elfn32.c:(.text+0x248d0): undefined reference to `elf_core_write_extra_phdrs'
binfmt_elfn32.c:(.text+0x24ac4): undefined reference to `elf_core_write_extra_data'
CONFIG_MIPS32_O32=y but CONFIG_BINFMT_ELF disabled results in the following
linker errors:
arch/mips/built-in.o: In function `elf_core_dump':
binfmt_elfo32.c:(.text+0x28a04): undefined reference to `elf_core_extra_phdrs'
binfmt_elfo32.c:(.text+0x29330): undefined reference to `elf_core_extra_data_size'
binfmt_elfo32.c:(.text+0x2951c): undefined reference to `elf_core_write_extra_phdrs'
binfmt_elfo32.c:(.text+0x29710): undefined reference to `elf_core_write_extra_data'
This is because binfmt_elfn32 and binfmt_elfo32 are using symbols from
elfcore but for these configurations elfcore will not be built.
Fixed by making elfcore selectable by a separate config symbol which
unlike the current mechanism can also be used from other directories
than kernel/, then having each flavor of ELF that relies on elfcore.o,
select it in Kconfig, including CONFIG_MIPS32_N32 and CONFIG_MIPS32_O32
which fixes this issue.
Link: http://lkml.kernel.org/r/20160520141705.GA1913@linux-mips.org Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Reviewed-by: James Hogan <james.hogan@imgtec.com> Cc: "Maciej W. Rozycki" <macro@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sending a packet, we will prepend it with an LAPB header.
This modifies the shared parts of a cloned skb, so we should copy the
skb rather than just clone it, before we prepend the header.
In "Documentation/networking/driver.rst" (the 2nd point), it states
that drivers shouldn't modify the shared parts of a cloned skb when
transmitting.
The "dev_queue_xmit_nit" function in "net/core/dev.c", which is called
when an skb is being sent, clones the skb and sents the clone to
AF_PACKET sockets. Because the LAPB drivers first remove a 1-byte
pseudo-header before handing over the skb to us, if we don't copy the
skb before prepending the LAPB header, the first byte of the packets
received on AF_PACKET sockets can be corrupted.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Xie He <xie.he.0141@gmail.com> Acked-by: Martin Schiller <ms@dev.tdt.de> Link: https://lore.kernel.org/r/20210201055706.415842-1-xie.he.0141@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sasha Levin [Fri, 5 Feb 2021 17:47:02 +0000 (12:47 -0500)]
stable: clamp SUBLEVEL in 4.4 and 4.9
Right now SUBLEVEL is overflowing, and some userspace may start treating
4.9.256 as 4.10. While out of tree modules have different ways of
extracting the version number (and we're generally ok with breaking
them), we do care about breaking userspace and it would appear that this
overflow might do just that.
Our rules around userspace ABI in the stable kernel are pretty simple:
we don't break it. Thus, while userspace may be checking major/minor, it
shouldn't be doing anything with sublevel.
This patch applies a big band-aid to the 4.9 and 4.4 kernels in the form
of clamping their sublevel to 255.
The clamp is done for the purpose of LINUX_VERSION_CODE only, and
extracting the version number from the Makefile or "make kernelversion"
will continue to work as intended.
We might need to do it later in newer trees, but maybe we'll have a
better solution by then, so I'm ignoring that problem for now.
While testing live partition mobility, we have observed occasional crashes
of the Linux partition. What we've seen is that during the live migration,
for specific configurations with large amounts of memory, slow network
links, and workloads that are changing memory a lot, the partition can end
up being suspended for 30 seconds or longer. This resulted in the following
scenario:
CPU 0 CPU 1
------------------------------- ----------------------------------
scsi_queue_rq migration_store
-> blk_mq_start_request -> rtas_ibm_suspend_me
-> blk_add_timer -> on_each_cpu(rtas_percpu_suspend_me
_______________________________________V
|
V
-> IPI from CPU 1
-> rtas_percpu_suspend_me
-> __rtas_suspend_last_cpu
Normally, the SCMD_STATE_COMPLETE bit would protect against the command
completion and the timeout, but that doesn't work here, since we don't
check that at all in the SCSI_MLQUEUE_HOST_BUSY path.
In this case we end up calling scsi_queue_insert on a request that has
already been queued, or possibly even freed, and we crash.
The patch below simply increases the default I/O timeout to avoid this race
condition. This is also the timeout value that nearly all IBM SAN storage
recommends setting as the default value.
A race condition exists between the response handler getting called because
of exchange_mgr_reset() (which clears out all the active XIDs) and the
response we get via an interrupt.
Sequence of events:
rport ba0200: Port timeout, state PLOGI
rport ba0200: Port entered PLOGI state from PLOGI state
xid 1052: Exchange timer armed : 20000 msecs  xid timer armed here
rport ba0200: Received LOGO request while in state PLOGI
rport ba0200: Delete port
rport ba0200: work event 3
rport ba0200: lld callback ev 3
bnx2fc: rport_event_hdlr: event = 3, port_id = 0xba0200
bnx2fc: ba0200 - rport not created Yet!!
/* Here we reset any outstanding exchanges before
freeing rport using the exch_mgr_reset() */
xid 1052: Exchange timer canceled
/* Here we got two responses for one xid */
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: invoking resp(), esb 20000000 state 3
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
xid 1052: fc_rport_plogi_resp() : ep->resp_active 2
Skip the response if the exchange is already completed.
Lee Jones [Thu, 4 Feb 2021 17:29:03 +0000 (17:29 +0000)]
futex: Handle faults correctly for PI futexes
From: Thomas Gleixner <tglx@linutronix.de>
fixup_pi_state_owner() tries to ensure that the state of the rtmutex,
pi_state and the user space value related to the PI futex are consistent
before returning to user space. In case that the user space value update
faults and the fault cannot be resolved by faulting the page in via
fault_in_user_writeable() the function returns with -EFAULT and leaves
the rtmutex and pi_state owner state inconsistent.
A subsequent futex_unlock_pi() operates on the inconsistent pi_state and
releases the rtmutex despite not owning it which can corrupt the RB tree of
the rtmutex and cause a subsequent kernel stack use after free.
It was suggested to loop forever in fixup_pi_state_owner() if the fault
cannot be resolved, but that results in runaway tasks which is especially
undesired when the problem happens due to a programming error and not due
to malice.
As the user space value cannot be fixed up, the proper solution is to make
the rtmutex and the pi_state consistent so both have the same owner. This
leaves the user space value out of sync. Any subsequent operation on the
futex will fail because the 10th rule of PI futexes (pi_state owner and
user space value are consistent) has been violated.
As a consequence this removes the inept attempts of 'fixing' the situation
in case that the current task owns the rtmutex when returning with an
unresolvable fault by unlocking the rtmutex which left pi_state::owner and
rtmutex::owner out of sync in a different and only slightly less dangerous
way.
Fixes: 1b7558e457ed ("futexes: fix fault handling in futex_lock_pi") Reported-by: gzobqq@gmail.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Too many gotos already and an upcoming fix would make it even more
unreadable.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No point in open coding it. This way it gains the extra sanity checks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Updating pi_state::owner is done at several places with the same
code. Provide a function for it and use that at the obvious places.
This is also a preparation for a bug fix to avoid yet another copy of the
same code or alternatively introducing a completely unpenetratable mess of
gotos.
Originally-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If that unexpected case of inconsistent arguments ever happens then the
futex state is left completely inconsistent and the printk is not really
helpful. Replace it with a warning and make the state consistent.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
/* At this point, we've returned -ETIMEDOUT to userspace, but the
* futex word shows waiter to be the owner, and the pi_mutex has
* stealer as the owner */
futex_lock(LOCK_PI, uaddr2)
-> bails with EDEADLK, futex word says we're owner.
removes from fixup_owner() looks to be just what is needed. And indeed
it is -- I completely missed that requeue_pi could also result in this
case. So we need to restore that, except that subsequent patches, like
commit:
16ffa12d7425 ("futex: Pull rt_mutex_futex_unlock() out from under hb->lock")
changed all the locking rules. Even without that, the sequence:
- raw_spin_lock_irq(&q->pi_state->pi_mutex.wait_lock);
- owner = rt_mutex_owner(&q->pi_state->pi_mutex);
- if (!owner)
- owner = rt_mutex_next_owner(&q->pi_state->pi_mutex);
- raw_spin_unlock_irq(&q->pi_state->pi_mutex.wait_lock);
- ret = fixup_pi_state_owner(uaddr, q, owner);
already suggests there were races; otherwise we'd never have to look
at next_owner.
So instead of doing 3 consecutive wait_lock sections with who knows
what races, we do it all in a single section. Additionally, the usage
of pi_state->owner in fixup_owner() was only safe because only the
rt_mutex owner would modify it, which this additional case wrecks.
Luckily the values can only change away and not to the value we're
testing, this means we can do a speculative test and double check once
we have the wait_lock.
Fixes: 73d786bd043e ("futex: Rework inconsistent rt_mutex/futex_q state") Reported-by: Julia Cartwright <julia@ni.com> Reported-by: Gratian Crisan <gratian.crisan@ni.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Julia Cartwright <julia@ni.com> Tested-by: Gratian Crisan <gratian.crisan@ni.com> Cc: Darren Hart <dvhart@infradead.org> Link: https://lkml.kernel.org/r/20171208124939.7livp7no2ov65rrc@hirez.programming.kicks-ass.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Lee: Back-ported to solve a dependency] Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a weird state in the futex_unlock_pi() path when it interleaves
with a concurrent futex_lock_pi() at the point where it drops hb->lock.
In this case, it can happen that the rt_mutex wait_list and the futex_q
disagree on pending waiters, in particular rt_mutex will find no pending
waiters where futex_q thinks there are. In this case the rt_mutex unlock
code cannot assign an owner.
The futex side fixup code has to cleanup the inconsistencies with quite a
bunch of interesting corner cases.
Simplify all this by changing wake_futex_pi() to return -EAGAIN when this
situation occurs. This then gives the futex_lock_pi() code the opportunity
to continue and the retried futex_unlock_pi() will now observe a coherent
state.
The only problem is that this breaks RT timeliness guarantees. That
is, consider the following scenario:
T1 and T2 are both pinned to CPU0. prio(T2) > prio(T1)
CPU0
T1
lock_pi()
queue_me() <- Waiter is visible
preemption
T2
unlock_pi()
loops with -EAGAIN forever
Which is undesirable for PI primitives. Future patches will rectify
this.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: juri.lelli@arm.com Cc: bigeasy@linutronix.de Cc: xlpang@redhat.com Cc: rostedt@goodmis.org Cc: mathieu.desnoyers@efficios.com Cc: jdesfossez@efficios.com Cc: dvhart@infradead.org Cc: bristot@redhat.com Link: http://lkml.kernel.org/r/20170322104151.850383690@infradead.org Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[Lee: Back-ported to solve a dependency] Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put the device to avoid resource leak on path that the polling flag is
invalid.
Fixes: a831b9132065 ("NFC: Do not return EBUSY when stopping a poll that's already stopped") Signed-off-by: Pan Bian <bianpan2016@163.com> Link: https://lore.kernel.org/r/20210121153745.122184-1-bianpan2016@163.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Goto to the label put_dev instead of the label error to fix potential
resource leak on path that the target index is invalid.
Fixes: c4fbb6515a4d ("NFC: The core part should generate the target index") Signed-off-by: Pan Bian <bianpan2016@163.com> Link: https://lore.kernel.org/r/20210121152748.98409-1-bianpan2016@163.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c40aaaac1018 ("iommu/vt-d: Gracefully handle DMAR units
with no supported address widths") dmar.c needs struct iommu_device to
be selected. We can drop this dependency by not dereferencing struct
iommu_device if IOMMU_API is not selected and by reusing the information
stored in iommu->drhd->ignored instead.
This fixes the following build error when IOMMU_API is not selected:
drivers/iommu/dmar.c: In function ‘free_iommu’:
drivers/iommu/dmar.c:1139:41: error: ‘struct iommu_device’ has no member named ‘ops’
1139 | if (intel_iommu_enabled && iommu->iommu.ops) {
^
Fixes: c40aaaac1018 ("iommu/vt-d: Gracefully handle DMAR units with no supported address widths") Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Acked-by: Lu Baolu <baolu.lu@linux.intel.com> Acked-by: David Woodhouse <dwmw@amazon.co.uk> Link: https://lore.kernel.org/r/20201013073055.11262-1-brgl@bgdev.pl Signed-off-by: Joerg Roedel <jroedel@suse.de>
[ - context change due to moving drivers/iommu/dmar.c to
drivers/iommu/intel/dmar.c
- set the drhr in the iommu like in upstream commit b1012ca8dc4f
("iommu/vt-d: Skip TE disabling on quirky gfx dedicated iommu") ] Signed-off-by: Filippo Sironi <sironi@amazon.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of bailing out completely, such a unit can still be used for
interrupt remapping.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk> Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/linux-iommu/549928db2de6532117f36c9c810373c14cf76f51.camel@infradead.org/ Signed-off-by: Joerg Roedel <jroedel@suse.de>
[ - context change due to moving drivers/iommu/dmar.c to
drivers/iommu/intel/dmar.c
- remove the unused err_unmap label
- use iommu->iommu_dev instead of iommu->iommu.ops to decide whether
when freeing ] Signed-off-by: Filippo Sironi <sironi@amazon.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "bec" struct isn't necessarily always initialized. For example, the
mcp251xfd_get_berr_counter() function doesn't initialize anything if the
interface is down.
Fixes: 52c793f24054 ("can: netlink support for bus-error reporting and counters") Link: https://lore.kernel.org/r/YAkaRdRJncsJO8Ve@mwanda Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported a crash that happened when changing the interface
type around a lot, and while it might have been easy to fix just
the symptom there, a little deeper investigation found that really
the reason is that we allowed packets to be transmitted while in
the middle of changing the interface type.
Disallow TX by stopping the queues while changing the type.
The max_recv_sge value is wrongly reported when calling query_qp, This is
happening due to a typo when assigning the max_recv_sge value, the value
of sq_max_sges was assigned instead of rq_max_sges.
Fixes: 3e5c02c9ef9a ("iw_cxgb4: Support query_qp() verb") Link: https://lore.kernel.org/r/20210114191423.423529-1-kamalheib1@gmail.com Signed-off-by: Kamal Heib <kamalheib1@gmail.com> Reviewed-by: Potnuri Bharat Teja <bharat@chelsio.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Analysis revealed offending code is when accessing:
replay_esn->bmp[nr] |= (1U << bitnr);
with 'nr' being 0x07fffffa.
This happened in an SMP system when reordering of packets was present;
A packet arrived with a "too old" sequence number (outside the window,
i.e 'diff > replay_window'), and therefore the following calculation:
bitnr = replay_esn->replay_window - (diff - pos);
yields a negative result, but since bitnr is u32 we get a large unsigned
quantity (in crash dump above: 0xffffff4b seen in ecx).
This was supposed to be protected by xfrm_input()'s former call to:
if (x->repl->check(x, skb, seq)) {
However, the state's spinlock x->lock is *released* after '->check()'
is performed, and gets re-acquired before '->advance()' - which gives a
chance for a different core to update the xfrm state, e.g. by advancing
'replay_esn->seq' when it encounters more packets - leading to a
'diff > replay_window' situation when original core continues to
xfrm_replay_advance_bmp().
An attempt to fix this issue was suggested in commit bcf66bf54aab
("xfrm: Perform a replay check after return from async codepaths"),
by calling 'x->repl->recheck()' after lock is re-acquired, but fix
applied only to asyncronous crypto algorithms.
Augment the fix, by *always* calling 'recheck()' - irrespective if we're
using async crypto.
Fixes: 0ebea8ef3559 ("[IPSEC]: Move state lock into x->type->input") Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Otherwise, the newly create element shows no timeout when listing the
ruleset. If the set definition does not specify a default timeout, then
the set element only shows the expiration time, but not the timeout.
This is a problem when restoring a stateful ruleset listing since it
skips the timeout policy entirely.
Fixes: 22fe54d5fefc ("netfilter: nf_tables: add support for dynamic set updates") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the kernel is configured to use the Thumb-2 instruction set
"suspend-to-memory" fails to resume. Observed on a Colibri iMX6ULL
(i.MX 6ULL) and Apalis iMX6 (i.MX 6Q).
It looks like the CPU resumes unconditionally in ARM instruction mode
and then chokes on the presented Thumb-2 code it should execute.
Fix this by using the arm instruction set for all code in
suspend-imx6.S.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Fixes: df595746fa69 ("ARM: imx: add suspend in ocram support for i.mx6q") Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--> preemption (unrelated wakeup of some other higher prio task, e.g. timer)
switch_to(other_task)
return to user
sys_futex()
loop infinite as above
Just for the fun of it the futex exit cleanup could trigger the wakeup
itself before the task sets its futex state to DEAD.
To cure this, the handling of the exiting owner is changed so:
- A refcount is held on the task
- The task pointer is stored in a caller visible location
- The caller drops all locks (hash bucket, mmap_sem) and blocks
on task::futex_exit_mutex. When the mutex is acquired then
the exiting task has completed the cleanup and the state
is consistent and can be reevaluated.
This is not a pretty solution, but there is no choice other than returning
an error code to user space, which would break the state consistency
guarantee and open another can of problems including regressions.
For stable backports the preparatory commits ac31c7ff8624 .. ba31c1a48538
are required as well, but for anything older than 5.3.y the backports are
going to be provided when this hits mainline as the other dependencies for
those kernels are definitely not stable material.
Fixes: 778e9a9c3e71 ("pi-futex: fix exit races and locking problems") Reported-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Stable Team <stable@vger.kernel.org> Link: https://lkml.kernel.org/r/20191106224557.041676471@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mutex will be used in subsequent changes to replace the busy looping of
a waiter when the futex owner is currently executing the exit cleanup to
prevent a potential live lock.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.845798895@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
exec() attempts to handle potentially held futexes gracefully by running
the futex exit handling code like exit() does.
The current implementation has no protection against concurrent incoming
waiters. The reason is that the futex state cannot be set to
FUTEX_STATE_DEAD after the cleanup because the task struct is still active
and just about to execute the new binary.
While its arguably buggy when a task holds a futex over exec(), for
consistency sake the state handling can at least cover the actual futex
exit cleanup section. This provides state consistency protection accross
the cleanup. As the futex state of the task becomes FUTEX_STATE_OK after the
cleanup has been finished, this cannot prevent subsequent attempts to
attach to the task in case that the cleanup was not successfull in mopping
up all leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.753355618@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of relying on PF_EXITING use an explicit state for the futex exit
and set it in the futex exit function. This moves the smp barrier and the
lock/unlock serialization into the futex code.
As with the DEAD state this is restricted to the exit path as exec
continues to use the same task struct.
This allows to simplify that logic in a next step.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.539409004@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting task::futex_state in do_exit() is rather arbitrarily placed for no
reason. Move it into the futex code.
Note, this is only done for the exit cleanup as the exec cleanup cannot set
the state to FUTEX_STATE_DEAD because the task struct is still in active
use.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.439511191@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To allow separate handling of the futex exit state in the futex exit code
for exit and exec, split futex_mm_release() into two functions and invoke
them from the corresponding exit/exec_mm_release() callsites.
Preparatory only, no functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.332094221@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The futex exit handling relies on PF_ flags. That's suboptimal as it
requires a smp_mb() and an ugly lock/unlock of the exiting tasks pi_lock in
the middle of do_exit() to enforce the observability of PF_EXITING in the
futex code.
Add a futex_state member to task_struct and convert the PF_EXITPIDONE logic
over to the new state. The PF_EXITING dependency will be cleaned up in a
later step.
This prepares for handling various futex exit issues later.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.149449274@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The futex exit handling is #ifdeffed into mm_release() which is not pretty
to begin with. But upcoming changes to address futex exit races need to add
more functionality to this exit code.
Split it out into a function, move it into futex code and make the various
futex exit functions static.
Preparatory only and no functional change.
Folded build fix from Borislav.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Ingo Molnar <mingo@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20191106224556.049705556@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are going to share the compat_sys_futex() handler between 64-bit
architectures and 32-bit architectures that need to deal with both 32-bit
and 64-bit time_t, and this is easier if both entry points are in the
same file.
In fact, most other system call handlers do the same thing these days, so
let's follow the trend here and merge all of futex_compat.c into futex.c.
In the process, a few minor changes have to be done to make sure everything
still makes sense: handle_futex_death() and futex_cmpxchg_enabled() become
local symbol, and the compat version of the fetch_robust_entry() function
gets renamed to compat_fetch_robust_entry() to avoid a symbol clash.
This is intended as a purely cosmetic patch, no behavior should
change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Lee: Back-ported to satisfy a build dependency] Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following crash log can occur unplugging the usb dongle since,
after the urb poison in mt7601u_free_tx_queue(), usb_submit_urb() will
always fail resulting in a skb kfree while the skb has been already
queued.
Fix the issue enqueuing the skb only if usb_submit_urb() succeed.
Fixes: 23377c200b2eb ("mt7601u: fix possible memory leak when the device is disconnected") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Jakub Kicinski <kubakici@wp.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/3b85219f669a63a8ced1f43686de05915a580489.1610919247.git.lorenzo@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since cfg80211 doesn't implement commit, we never really cared about
that code there (and it's configured out w/o CONFIG_WIRELESS_EXT).
After all, since it has no commit, it shouldn't return -EIWCOMMIT to
indicate commit is needed.
However, EIWCOMMIT is actually an alias for EINPROGRESS, which _can_
happen if e.g. we try to change the frequency but we're already in
the process of connecting to some network, and drivers could return
that value (or even cfg80211 itself might).
This then causes us to crash because dev->wireless_handlers is NULL
but we try to check dev->wireless_handlers->standard[0].
Fix this by also checking dev->wireless_handlers. Also simplify the
code a little bit.
Commit 8765c5ba1949 ("ACPI / scan: Rework modalias creation when
"compatible" is present") may create two "MODALIAS=" in one uevent
file if specific conditions are met.
This breaks systemd-udevd, which assumes each "key" in one uevent file
to be unique. The internal implementation of systemd-udevd overwrites
the first MODALIAS with the second one, so its kmod rule doesn't load
the driver for the first MODALIAS.
So if both the ACPI modalias and the OF modalias are present, use the
latter to ensure that there will be only one MODALIAS.
Link: https://github.com/systemd/systemd/pull/18163 Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Fixes: 8765c5ba1949 ("ACPI / scan: Rework modalias creation when "compatible" is present") Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: 4.1+ <stable@vger.kernel.org> # 4.1+
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The x86-64 psABI [0] specifies special relocation types
(R_X86_64_[REX_]GOTPCRELX) for indirection through the Global Offset
Table, semantically equivalent to R_X86_64_GOTPCREL, which the linker
can take advantage of for optimization (relaxation) at link time. This
is supported by LLD and binutils versions 2.26 onwards.
The compressed kernel is position-independent code, however, when using
LLD or binutils versions before 2.27, it must be linked without the -pie
option. In this case, the linker may optimize certain instructions into
a non-position-independent form, by converting foo@GOTPCREL(%rip) to $foo.
This potential issue has been present with LLD and binutils-2.26 for a
long time, but it has never manifested itself before now:
- LLD and binutils-2.26 only relax
movq foo@GOTPCREL(%rip), %reg
to
leaq foo(%rip), %reg
which is still position-independent, rather than
mov $foo, %reg
which is permitted by the psABI when -pie is not enabled.
- GCC happens to only generate GOTPCREL relocations on mov instructions.
- CLang does generate GOTPCREL relocations on non-mov instructions, but
when building the compressed kernel, it uses its integrated assembler
(due to the redefinition of KBUILD_CFLAGS dropping -no-integrated-as),
which has so far defaulted to not generating the GOTPCRELX
relocations.
Nick Desaulniers reports [1,2]:
"A recent change [3] to a default value of configuration variable
(ENABLE_X86_RELAX_RELOCATIONS OFF -> ON) in LLVM now causes Clang's
integrated assembler to emit R_X86_64_GOTPCRELX/R_X86_64_REX_GOTPCRELX
relocations. LLD will relax instructions with these relocations based
on whether the image is being linked as position independent or not.
When not, then LLD will relax these instructions to use absolute
addressing mode (R_RELAX_GOT_PC_NOPIC). This causes kernels built with
Clang and linked with LLD to fail to boot."
Patch series [4] is a solution to allow the compressed kernel to be
linked with -pie unconditionally, but even if merged is unlikely to be
backported. As a simple solution that can be applied to stable as well,
prevent the assembler from generating the relaxed relocation types using
the -mrelax-relocations=no option. For ease of backporting, do this
unconditionally.
When xen_blkif_disconnect() is called, the kernel thread behind the
block interface is stopped by calling kthread_stop(ring->xenblkd).
The ring->xenblkd thread pointer being non-NULL determines if the
thread has been already stopped.
Normally, the thread's function xen_blkif_schedule() sets the
ring->xenblkd to NULL, when the thread's main loop ends.
However, when the thread has not been started yet (i.e.
wake_up_process() has not been called on it), the xen_blkif_schedule()
function would not be called yet.
In such case the kthread_stop() call returns -EINTR and the
ring->xenblkd remains dangling.
When this happens, any consecutive call to xen_blkif_disconnect (for
example in frontend_changed() callback) leads to a kernel crash in
kthread_stop() (e.g. NULL pointer dereference in exit_creds()).
This is XSA-350.
Cc: <stable@vger.kernel.org> # 4.12 Fixes: a24fa22ce22a ("xen/blkback: don't use xen_blkif_get() in xen-blkback kthread") Reported-by: Olivier Benjamin <oliben@amazon.com> Reported-by: Pawel Wieczorkiewicz <wipawel@amazon.de> Signed-off-by: Pawel Wieczorkiewicz <wipawel@amazon.de> Reviewed-by: Julien Grall <jgrall@amazon.com> Reviewed-by: Juergen Gross <jgross@suse.com> Signed-off-by: Juergen Gross <jgross@suse.com>
[iwamatsu: change from ring to blkif] Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Below race can come, if trace_open and resize of
cpu buffer is running parallely on different cpus
CPUX CPUY
ring_buffer_resize
atomic_read(&buffer->resize_disabled)
tracing_open
tracing_reset_online_cpus
ring_buffer_reset_cpu
rb_reset_cpu
rb_update_pages
remove/insert pages
resetting pointer
This race can cause data abort or some times infinte loop in
rb_remove_pages and rb_insert_pages while checking pages
for sanity.
Take buffer lock to fix this.
Link: https://lkml.kernel.org/r/1601976833-24377-1-git-send-email-gkohli@codeaurora.org Cc: stable@vger.kernel.org Fixes: 83f40318dab00 ("ring-buffer: Make removal of ring buffer pages atomic") Reported-by: Denis Efremov <efremov@linux.com> Signed-off-by: Gaurav Kohli <gkohli@codeaurora.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ff00::/8 multicast route is created without specifying the fc_protocol
field, so the default RTPROT_BOOT value is used:
$ ip -6 -d route
unicast ::1 dev lo proto kernel scope global metric 256 pref medium
unicast fe80::/64 dev eth0 proto kernel scope global metric 256 pref medium
unicast ff00::/8 dev eth0 proto boot scope global metric 256 pref medium
As the documentation says, this value identifies routes installed during
boot, but the route is created when interface is set up.
Change the value to RTPROT_KERNEL which is a better value.
Commit 3226b158e67c ("net: avoid 32 x truesize under-estimation for
tiny skbs") ensured that skbs with data size lower than 1025 bytes
will be kmalloc'ed to avoid excessive page cache fragmentation and
memory consumption.
However, the fix adressed only __napi_alloc_skb() (primarily for
virtio_net and napi_get_frags()), but the issue can still be achieved
through __netdev_alloc_skb(), which is still used by several drivers.
Drivers often allocate a tiny skb for headers and place the rest of
the frame to frags (so-called copybreak).
Mirror the condition to __netdev_alloc_skb() to handle this case too.
sh_eth_close() does a synchronous power down of the device before
marking it closed. Revert the order, to make sure the device is never
marked opened while suspended.
While at it, use pm_runtime_put() instead of pm_runtime_put_sync(), as
there is no reason to do a synchronous power down.
Fixes: 7fa2955ff70ce453 ("sh_eth: Fix sleeping function called from invalid context") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se> Link: https://lore.kernel.org/r/20210118150812.796791-1-geert+renesas@glider.be Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When G2_DMA is enabled and SH_DMA is disabled, it results in the following
Kbuild warning:
WARNING: unmet direct dependencies detected for SH_DMA_API
Depends on [n]: SH_DMA [=n]
Selected by [y]:
- G2_DMA [=y] && SH_DREAMCAST [=y]
The reason is that G2_DMA selects SH_DMA_API without depending on or
selecting SH_DMA while SH_DMA_API depends on SH_DMA.
When G2_DMA was first introduced with commit 40f49e7ed77f
("sh: dma: Make G2 DMA configurable."), this wasn't an issue since
SH_DMA_API didn't have such dependency, and this way was the only way to
enable it since SH_DMA_API was non-visible. However, later SH_DMA_API was
made visible and dependent on SH_DMA with commit d8902adcc1a9
("dmaengine: sh: Add Support SuperH DMA Engine driver").
Let G2_DMA depend on SH_DMA_API instead to avoid Kbuild issues.
RT_TOS() only masks one of the two ECN bits. Therefore rpfilter_mt()
treats Not-ECT or ECT(1) packets in a different way than those with
ECT(0) or CE.
Reproducer:
Create two netns, connected with a veth:
$ ip netns add ns0
$ ip netns add ns1
$ ip link add name veth01 netns ns0 type veth peer name veth10 netns ns1
$ ip -netns ns0 link set dev veth01 up
$ ip -netns ns1 link set dev veth10 up
$ ip -netns ns0 address add 192.0.2.10/32 dev veth01
$ ip -netns ns1 address add 192.0.2.11/32 dev veth10
Add a route to ns1 in ns0:
$ ip -netns ns0 route add 192.0.2.11/32 dev veth01
In ns1, only packets with TOS 4 can be routed to ns0:
$ ip -netns ns1 route add 192.0.2.10/32 tos 4 dev veth10
Ping from ns0 to ns1 works regardless of the ECN bits, as long as TOS
is 4:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 0% packet loss ...
Now use iptable's rpfilter module in ns1:
$ ip netns exec ns1 iptables-legacy -t raw -A PREROUTING -m rpfilter --invert -j DROP
Not-ECT and ECT(1) packets still pass:
$ ip netns exec ns0 ping -Q 4 192.0.2.11 # TOS 4, Not-ECT
... 0% packet loss ...
$ ip netns exec ns0 ping -Q 5 192.0.2.11 # TOS 4, ECT(1)
... 0% packet loss ...
But ECT(0) and ECN packets are dropped:
$ ip netns exec ns0 ping -Q 6 192.0.2.11 # TOS 4, ECT(0)
... 100% packet loss ...
$ ip netns exec ns0 ping -Q 7 192.0.2.11 # TOS 4, CE
... 100% packet loss ...
After this patch, rpfilter doesn't drop ECT(0) and CE packets anymore.
GCC versions >= 4.9 and < 5.1 have been shown to emit memory references
beyond the stack pointer, resulting in memory corruption if an interrupt
is taken after the stack pointer has been adjusted but before the
reference has been executed. This leads to subtle, infrequent data
corruption such as the EXT4 problems reported by Russell King at the
link below.
Life is too short for buggy compilers, so raise the minimum GCC version
required by arm64 to 5.1.
Reported-by: Russell King <linux@armlinux.org.uk> Suggested-by: Arnd Bergmann <arnd@kernel.org> Signed-off-by: Will Deacon <will@kernel.org> Tested-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: <stable@vger.kernel.org> Cc: Theodore Ts'o <tytso@mit.edu> Cc: Florian Weimer <fweimer@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20210105154726.GD1551@shell.armlinux.org.uk Link: https://lore.kernel.org/r/20210112224832.10980-1-will@kernel.org Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[will: backport to 4.4.y/4.9.y/4.14.y; add __clang__ check] Link: https://lore.kernel.org/r/CA+G9fYuzE9WMSB7uGjV4gTzK510SHEdJb_UXQCzsQ5MqA=h9SA@mail.gmail.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once the command ring doorbell is rung the xHC controller will parse all
command TRBs on the command ring that have the cycle bit set properly.
If the driver just started writing the next command TRB to the ring when
hardware finished the previous TRB, then HW might fetch an incomplete TRB
as long as its cycle bit set correctly.
A command TRB is 16 bytes (128 bits) long.
Driver writes the command TRB in four 32 bit chunks, with the chunk
containing the cycle bit last. This does however not guarantee that
chunks actually get written in that order.
This was detected in stress testing when canceling URBs with several
connected USB devices.
Two consecutive "Set TR Dequeue pointer" commands got queued right
after each other, and the second one was only partially written when
the controller parsed it, causing the dequeue pointer to be set
to bogus values. This was seen as error messages:
"Mismatch between completed Set TR Deq Ptr command & xHCI internal state"
Solution is to add a write memory barrier before writing the cycle bit.
The bdc pci driver is going to be removed due to it not existing in the
wild. This patch turns off compilation of the driver so that stable
kernels can also pick up the change. This helps the out-of-tree
facetimehd webcam driver as the pci id conflicts with bdc.
Cc: Al Cooper <alcooperx@gmail.com> Cc: <stable@vger.kernel.org> Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Link: https://lore.kernel.org/r/20210118203615.13995-1-patrik.r.jakobsson@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The power-down mask of the ad5504 is actually a power-up mask. Meaning if
a bit is set the corresponding channel is powered up and if it is not set
the channel is powered down.
The driver currently has this the wrong way around, resulting in the
channel being powered up when requested to be powered down and vice versa.
Fixes: 3bbbf150ffde ("staging:iio:dac:ad5504: Use strtobool for boolean values") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Alexandru Ardelean <alexandru.ardelean@analog.com> Link: https://lore.kernel.org/r/20201209104649.5794-1-lars@metafoo.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After calling netif_rx_ni(skb), dereferencing skb is unsafe.
Especially, the can_frame cf which aliases skb memory is accessed
after the netif_rx_ni() in:
stats->rx_bytes += cf->len;
Reordering the lines solves the issue.
Fixes: 39549eef3587 ("can: CAN Network device driver and Netlink interface") Link: https://lore.kernel.org/r/20210120114137.200019-2-mailhol.vincent@wanadoo.fr Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
This issue has generally been covered up by the presence of additional
expansion ROMs after the ones we're interested in, with header fetches
of subsequent images loading enough of the ROM to hide the issue.
Noticed on GA102, which lacks a type 0x70 image compared to TU102,.
[ 906.364197] nouveau 0000:09:00.0: bios: 00000000: type 00, 65024 bytes
[ 906.381205] nouveau 0000:09:00.0: bios: 0000fe00: type 03, 91648 bytes
[ 906.405213] nouveau 0000:09:00.0: bios: 00026400: type e0, 22016 bytes
[ 906.410984] nouveau 0000:09:00.0: bios: 0002ba00: type e0, 366080 bytes
vs
[ 22.961901] nouveau 0000:09:00.0: bios: 00000000: type 00, 60416 bytes
[ 22.984174] nouveau 0000:09:00.0: bios: 0000ec00: type 03, 71168 bytes
[ 23.010446] nouveau 0000:09:00.0: bios: 00020200: type e0, 48128 bytes
[ 23.028220] nouveau 0000:09:00.0: bios: 0002be00: type e0, 140800 bytes
[ 23.080196] nouveau 0000:09:00.0: bios: 0004e400: type 70, 7168 bytes
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Users can initiate resets to specific SCSI device/target/host through
IOCTL. When this happens, the SCSI cmd passed to eh_device/target/host
_reset_handler() callbacks is initialized with a request whose tag is -1.
In this case it is not right for eh_device_reset_handler() callback to
count on the LUN get from hba->lrb[-1]. Fix it by getting LUN from the SCSI
device associated with the SCSI cmd.
Link: https://lore.kernel.org/r/1609157080-26283-1-git-send-email-cang@codeaurora.org Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Stanley Chu <stanley.chu@mediatek.com> Signed-off-by: Can Guo <cang@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
haswell machine board is missing pm_ops what prevents it from undergoing
suspend-resume procedure successfully. Assign default snd_soc_pm_ops so
this is no longer the case.
This reverts commit 644bda6f3460 ("dm table: fall back to getting device using name_to_dev_t()")
dm_get_dev_t() is just used to convert an arbitrary 'path' string
into a dev_t. It doesn't presume that the device is present; that
check will be done later, as the only caller is dm_get_device(),
which does a dm_get_table_device() later on, which will properly
open the device.
So if the path string already _is_ in major:minor representation
we can convert it directly, avoiding a recursion into the filesystem
to lookup the block device.
This avoids a hang in multipath_message() when the filesystem is
inaccessible.
Fixes: 644bda6f3460 ("dm table: fall back to getting device using name_to_dev_t()") Cc: stable@vger.kernel.org Signed-off-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Martin Wilck <mwilck@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the acpi_device pointer which acpi_bus_get_device() returns-by-
reference to NULL on errors.
We've recently had 2 cases where callers of acpi_bus_get_device()
did not properly error check the return value, so set the returned-
by-reference acpi_device pointer to NULL, because at least some
callers of acpi_bus_get_device() expect that to be done on errors.
[ rjw: This issue was exposed by commit 71da201f38df ("ACPI: scan:
Defer enumeration of devices with _DEP lists") which caused it to
be much more likely to occur on some systems, but the real defect
had been introduced by an earlier commit. ]
Fixes: 40e7fcb19293 ("ACPI: Add _DEP support to fix battery issue on Asus T100TA") Fixes: bcfcd409d4db ("usb: split code locating ACPI companion into port and device") Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Diagnosed-by: Rafael J. Wysocki <rafael@kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Cc: All applicable <stable@vger.kernel.org>
[ rjw: Subject and changelog edits ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turned out that VIA codecs also mute the sound in the lowest mixer
level. Turn on the dac_min_mute flag to indicate the mute-as-minimum
in TLV like already done in Conexant and IDT codecs.
snd_seq_oss_synth_make_info() didn't check the error code from
snd_seq_oss_midi_make_info(), and this leads to the call of strlcpy()
with the uninitialized string as the source, which may lead to the
access over the limit.
Add the proper error check for avoiding the failure.
Both virtio net and napi_get_frags() allocate skbs
with a very small skb->head
While using page fragments instead of a kmalloc backed skb->head might give
a small performance improvement in some cases, there is a huge risk of
under estimating memory usage.
For both GOOD_COPY_LEN and GRO_MAX_HEAD, we can fit at least 32 allocations
per page (order-3 page in x86), or even 64 on PowerPC
We have been tracking OOM issues on GKE hosts hitting tcp_mem limits
but consuming far more memory for TCP buffers than instructed in tcp_mem[2]
Even if we force napi_alloc_skb() to only use order-0 pages, the issue
would still be there on arches with PAGE_SIZE >= 32768
This patch makes sure that small skb head are kmalloc backed, so that
other objects in the slab page can be reused instead of being held as long
as skbs are sitting in socket queues.
Note that we might in the future use the sk_buff napi cache,
instead of going through a more expensive __alloc_skb()
Another idea would be to use separate page sizes depending
on the allocated length (to never have more than 4 frags per page)
I would like to thank Greg Thelen for his precious help on this matter,
analysing crash dumps is always a time consuming task.
Fixes: fd11a83dd363 ("net: Pull out core bits of __netdev_alloc_skb and add __napi_alloc_skb") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Greg Thelen <gthelen@google.com> Reviewed-by: Alexander Duyck <alexanderduyck@fb.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Link: https://lore.kernel.org/r/20210113161819.1155526-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net/rxrpc/key.c:657:11: warning: Assigned value is garbage or undefined
toksize = toksizes[tok++];
^ ~~~~~~~~~~~~~~~
rxrpc_read() contains two consecutive loops. The first loop calculates the
token sizes and stores the results in toksizes[] and the second one uses
the array. When there is an error in identifying the token in the first
loop, the token is skipped, no change is made to the toksizes[] array.
When the same error happens in the second loop, the token is not skipped.
This will cause the toksizes[] array to be out of step and will overrun
past the calculated sizes.
Fix this by making both loops log a message and return an error in this
case. This should only happen if a new token type is incompletely
implemented, so it should normally be impossible to trigger this.
Fixes: 9a059cd5ca7d ("rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()") Reported-by: Tom Rix <trix@redhat.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Tom Rix <trix@redhat.com> Link: https://lore.kernel.org/r/161046503122.2445787.16714129930607546635.stgit@warthog.procyon.org.uk Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to unregister the netdevice if config failed.
.ndo_uninit takes care of most of the heavy lifting.
This was uncovered by recent commit c269a24ce057 ("net: make
free_netdev() more lenient with unregistering devices").
Previously the partially-initialized device would be left
in the system.
Reported-and-tested-by: syzbot+2393580080a2da190f04@syzkaller.appspotmail.com Fixes: e2f1f072db8d ("sit: allow to configure 6rd tunnels via netlink") Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Link: https://lore.kernel.org/r/20210114012947.2515313-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 826f328e2b7e ("net: dcb: Validate netlink message in DCB
handler"), Linux started rejecting RTM_GETDCB netlink messages if they
contained a set-like DCB_CMD_ command.
The reason was that privileges were only verified for RTM_SETDCB messages,
but the value that determined the action to be taken is the command, not
the message type. And validation of message type against the DCB command
was the obvious missing piece.
Unfortunately it turns out that mlnx_qos, a somewhat widely deployed tool
for configuration of DCB, accesses the DCB set-like APIs through
RTM_GETDCB.
Therefore do not bounce the discrepancy between message type and command.
Instead, in addition to validating privileges based on the actual message
type, validate them also based on the expected message type. This closes
the loophole of allowing DCB configuration on non-admin accounts, while
maintaining backward compatibility.
Fixes: 2f90b8657ec9 ("ixgbe: this patch adds support for DCB to the kernel and ixgbe driver") Fixes: 826f328e2b7e ("net: dcb: Validate netlink message in DCB handler") Signed-off-by: Petr Machata <petrm@nvidia.com> Link: https://lore.kernel.org/r/a3edcfda0825f2aa2591801c5232f2bbf2d8a554.1610384801.git.me@pmachata.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log