On May 4th, Bjørn Mork provided patch 697bbc7b8320 ("builddeb: include
objtool binary in headers package"). However, that one only works if
$srctree=$objtree, because the objtool binaries are not written to the
srctree, but to the objtree.
Signed-off-by: Wilfried Klaebe <linux-kernel@lebenslange-mailadresse.de> Fixes: 697bbc7b8320 ("builddeb: include objtool binary in headers package") Signed-off-by: Michal Marek <mmarek@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There exists a race where the application can setup a connection
and then disconnect it before iw_cxgb4 processes the fw4_ack
message. For passive side connections, the fw4_ack message is
used to know when to stop the ep timer for MPA_REPLY messages.
If the application disconnects before the fw4_ack is handled then
c4iw_ep_disconnect() needs to clean up the timer state and stop the
timer before restarting it for the disconnect timer. Failure to do this
results in a "timer already started" message and a premature stopping
of the disconnect timer.
Fixes: e4b76a2 ("RDMA/iw_cxgb4: stop_ep_timer() after MPA negotiation") Signed-off-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently we call quarantine_reduce() for ___GFP_KSWAPD_RECLAIM (implied
by __GFP_RECLAIM) allocation. So, basically we call it on almost every
allocation. quarantine_reduce() sometimes is heavy operation, and
calling it with disabled interrupts may trigger hard LOCKUP:
If the total amount of memory assigned to quarantine is less than the
amount of memory assigned to per-cpu quarantines, |new_quarantine_size|
may overflow. Instead, set it to zero.
Commit 0259f522e04f ('soc/tegra: pmc: Restore base address on probe
failure') fixes an issue where the PMC base address pointer is not
restored on probe failure. However, this fix creates another problem
where if early initialisation of the PMC driver fails and an initial
mapping for the PMC address space is not created, then when the PMC
device is probed, the PMC base address pointer will not be valid and
this will cause a crash when tegra_pmc_init() is called and attempts
to access a register.
Although the PMC address space is mapped a 2nd time during the probe
and so this could be fixed by populating the base address pointer
earlier during the probe, this adds more complexity to the code.
Moreover, the PMC probe also assumes the the soc data pointer is also
initialised when the device is probed and if not will also lead to a
crash when calling tegra_pmc_init_tsense_reset(). Given that if the
early initialisation does fail then something bad has happen, it seems
acceptable to allow the PMC device probe to fail as well. Therefore, if
the PMC base address pointer or soc data pointer are not valid when
probing the PMC device, WARN and return an error.
Fixes: 0259f522e04f ('soc/tegra: pmc: Restore base address on probe failure') Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix PHY delay compensation math in igb_ptp_tx_hwtstamp() and
igb_ptp_rx_rgtstamp. Add PHY delay compensation in
igb_ptp_rx_pktstamp().
In the IGB driver, there are two functions that retrieve timestamps
received by the PHY - igb_ptp_rx_rgtstamp() and igb_ptp_rx_pktstamp().
The previous commit only changed igb_ptp_rx_rgtstamp(), and the change
was incorrect.
There are two instances in which PHY delay compensations should be
made:
- Before the packet transmission over the PHY, the latency between
when the packet is timestamped and transmission of the packets,
should be an add operation, but it is currently a subtract.
- After the packets are received from the PHY, the latency between
the receiving and timestamping of the packets should be a subtract
operation, but it is currently an add.
Signed-off-by: Kshitiz Gupta <kshitiz.gupta@ni.com> Fixes: 3f544d2 (igb: adjust ptp timestamps for tx/rx latency) Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit. This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV. This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.
Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.
Fixes: 16369564915a ("ixgbe: Add support for VLAN promiscuous with SR-IOV") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device's model download function returns the model data as
an array of u32s, which is later compared to the reference
model data. However, since the latter is an array of u16s,
the comparison does not happen correctly, and model verification
fails. This in turn breaks the POR initialization sequence.
Fixes: 39e7213edc4f3 ("max17042_battery: Support regmap to access device's registers") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Sebastian Reichel <sre@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtree_next_node() walks the linked list of leaf nodes to find the next
block of pages in the struct memory_bitmap. If it walks off the end of
the list of nodes, it walks the list of memory zones to find the next
region of memory. If it walks off the end of the list of zones, it
returns false.
This leaves the struct bm_position's node and zone pointers pointing
at their respective struct list_heads in struct mem_zone_bm_rtree.
memory_bm_find_bit() uses struct bm_position's node and zone pointers
to avoid walking lists and trees if the next bit appears in the same
node/zone. It handles these values being stale.
Swap rtree_next_node()s 'step then test' to 'test-next then step',
this means if we reach the end of memory we return false and leave
the node and zone pointers as they were.
This fixes a panic on resume using AMD Seattle with 64K pages:
[ 6.868732] Freezing user space processes ... (elapsed 0.000 seconds) done.
[ 6.875753] Double checking all user space processes after OOM killer disable... (elapsed 0.000 seconds)
[ 6.896453] PM: Using 3 thread(s) for decompression.
[ 6.896453] PM: Loading and decompressing image data (5339 pages)...
[ 7.318890] PM: Image loading progress: 0%
[ 7.323395] Unable to handle kernel paging request at virtual address 00800040
[ 7.330611] pgd = ffff000008df0000
[ 7.334003] [00800040] *pgd=00000083fffe0003, *pud=00000083fffe0003, *pmd=00000083fffd0003, *pte=0000000000000000
[ 7.344266] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 7.349825] Modules linked in:
[ 7.352871] CPU: 2 PID: 1 Comm: swapper/0 Tainted: G W I 4.8.0-rc1 #4737
[ 7.360512] Hardware name: AMD Overdrive/Supercharger/Default string, BIOS ROD1002C 04/08/2016
[ 7.369109] task: ffff8003c0220000 task.stack: ffff8003c0280000
[ 7.375020] PC is at set_bit+0x18/0x30
[ 7.378758] LR is at memory_bm_set_bit+0x24/0x30
[ 7.383362] pc : [<ffff00000835bbc8>] lr : [<ffff0000080faf18>] pstate: 60000045
[ 7.390743] sp : ffff8003c0283b00
[ 7.473551]
[ 7.475031] Process swapper/0 (pid: 1, stack limit = 0xffff8003c0280020)
[ 7.481718] Stack: (0xffff8003c0283b00 to 0xffff8003c0284000)
[ 7.800075] Call trace:
[ 7.887097] [<ffff00000835bbc8>] set_bit+0x18/0x30
[ 7.891876] [<ffff0000080fb038>] duplicate_memory_bitmap.constprop.38+0x54/0x70
[ 7.899172] [<ffff0000080fcc40>] snapshot_write_next+0x22c/0x47c
[ 7.905166] [<ffff0000080fe1b4>] load_image_lzo+0x754/0xa88
[ 7.910725] [<ffff0000080ff0a8>] swsusp_read+0x144/0x230
[ 7.916025] [<ffff0000080fa338>] load_image_and_restore+0x58/0x90
[ 7.922105] [<ffff0000080fa660>] software_resume+0x2f0/0x338
[ 7.927752] [<ffff000008083350>] do_one_initcall+0x38/0x11c
[ 7.933314] [<ffff000008b40cc0>] kernel_init_freeable+0x14c/0x1ec
[ 7.939395] [<ffff0000087ce564>] kernel_init+0x10/0xfc
[ 7.944520] [<ffff000008082e90>] ret_from_fork+0x10/0x40
[ 7.949820] Code: d28000228b400c21f98000319ac32043 (c85f7c22)
[ 7.955909] ---[ end trace 0024a5986e6ff323 ]---
[ 7.960529] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Here struct mem_zone_bm_rtree's start_pfn has been returned instead of
struct rtree_node's addr as the node/zone pointers are corrupt after
we walked off the end of the lists during mark_unsafe_pages().
This behaviour was exposed by commit 6dbecfd345a6 ("PM / hibernate:
Simplify mark_unsafe_pages()"), which caused mark_unsafe_pages() to call
duplicate_memory_bitmap(), which uses memory_bm_find_bit() after walking
off the end of the memory bitmap.
Fixes: 3a20cb177961 (PM / Hibernate: Implement position keeping in radix tree) Signed-off-by: James Morse <james.morse@arm.com>
[ rjw: Subject ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restore the processor state before calling any other functions to
ensure per-CPU variables can be used with KASLR memory randomization.
Tracing functions use per-CPU variables (GS based on x86) and one was
called just before restoring the processor state fully. It resulted
in a double fault when both the tracing & the exception handler
functions tried to use a per-CPU variable.
Fixes: bb3632c6101b (PM / sleep: trace events for suspend/resume) Reported-and-tested-by: Borislav Petkov <bp@suse.de> Reported-by: Jiri Kosina <jikos@kernel.org> Tested-by: Rafael J. Wysocki <rafael@kernel.org> Tested-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Thomas Garnier <thgarnie@google.com> Acked-by: Pavel Machek <pavel@ucw.cz> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function ceph_alloc_page_vector() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Fixes: 1907920324f1 ('libceph: support for sending notifies') Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ceph_llseek does not correctly return NXIO errors because the 'out' path
always returns 'offset'.
Fixes: 06222e491e66 ("fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek") Signed-off-by: Phil Turnbull <phil.turnbull@oracle.com> Signed-off-by: Yan, Zheng <zyan@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The genksyms helper in the kernel cannot parse a type definition
like "typeof(((type *)0)->keyfld)" that is used in the DEFINE_RB_FUNCS
helper, causing the following EXPORT_SYMBOL() statement to be ignored
when computing the crcs, and triggering a warning about this:
WARNING: "ceph_monc_do_statfs" [fs/ceph/ceph.ko] has no CRC
To work around the problem, we can rewrite the type to reference
an undefined 'extern' symbol instead of a NULL pointer. This is
evidently ok for genksyms, and it no longer complains about the
line when calling it with 'genksyms -w'.
I've looked briefly into extending genksyms instead, but it seems
really hard to do. Jan Beulich introduced basic support for 'typeof'
a while ago in dc53324060f3 ("genksyms: fix typeof() handling"),
but that is not sufficient for the expression we have here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: fcd00b68bbe2 ("libceph: DEFINE_RB_FUNCS macro") Cc: Jan Beulich <jbeulich@suse.com> Cc: Michal Marek <mmarek@suse.cz> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An on-stack oid in ceph_ioctl_get_dataloc() is not initialized,
resulting in a WARN and a NULL pointer dereference later on. We will
have more of these on-stack in the future, so fix it with a convenience
macro.
There's a mixture of signed 32-bit and unsigned 32-bit and 64-bit data
types used for keeping track of how many pages have been mapped.
This leads to hangs during boot when mapping large numbers of pages
(multiple terabytes, as reported by Waiman) because those values are
interpreted as being negative.
commit 742563777e8d ("x86/mm/pat: Avoid truncation when converting
cpa->numpages to address") fixed one of those bugs, but there is
another lurking in __change_page_attr_set_clr().
Additionally, the return value type for the populate_*() functions can
return negative values when a large number of pages have been mapped,
triggering the error paths even though no error occurred.
Consistently use 64-bit types on 64-bit platforms when counting pages.
Even in the signed case this gives us room for regions 8PiB
(pebibytes) in size whilst still allowing the usual negative value
error checking idiom.
cpu_has_fpu macro uses smp_processor_id() and is currently executed
with preemption enabled, that triggers the warning at runtime.
It is assumed throughout the kernel that if any CPU has an FPU, then all
CPUs would have an FPU as well, so it is safe to perform the check with
preemption enabled - change the code to use raw_ variant of the check to
avoid the warning.
Commit c1a0e9bc885d ("MIPS: Allow compact branch policy to be changed")
added Kconfig entries allowing for the compact branch policy used by the
compiler for MIPSr6 kernels to be specified. This can be useful for
debugging, particularly in systems where compact branches have recently
been introduced.
Unfortunately mainline gcc 5.x supports MIPSr6 but not the
-mcompact-branches compiler flag, leading to MIPSr6 kernels failing to
build with gcc 5.x with errors such as:
Fixing this by hiding the Kconfig entry behind another seems to be more
hassle than it's worth, as MIPSr6 & compact branches have been around
for a while now and if policy does need to be set for debug it can be
done easily enough with KCFLAGS. Therefore remove the compact branch
policy Kconfig entries & their handling in the Makefile.
This reverts commit c1a0e9bc885d ("MIPS: Allow compact branch policy to
be changed").
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reported-by: kbuild test robot <fengguang.wu@intel.com> Fixes: c1a0e9bc885d ("MIPS: Allow compact branch policy to be changed") Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14241/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The page structures associated with the vDSO pages in the kernel image
are calculated using virt_to_page(), which uses __pa() under the hood to
find the pfn associated with the virtual address. The vDSO data pointers
however point to kernel symbols, so __pa_symbol() should really be used
instead.
Since there is no equivalent to virt_to_page() which uses __pa_symbol(),
fix init_vdso_image() to work directly with pfns, calculated with
__phys_to_pfn(__pa_symbol(...)).
This issue broke the Malta Enhanced Virtual Addressing (EVA)
configuration which has a non-default implementation of __pa_symbol().
This is because it uses a physical alias so that the kernel executes
from KSeg0 (VA 0x80000000 -> PA 0x00000000), while RAM is provided to
the kernel in the KUSeg range (VA 0x00000000 -> PA 0x80000000) which
uses the same underlying RAM.
Since there are no page structures associated with the low physical
address region, some arbitrary kernel memory would be interpreted as a
page structure for the vDSO pages and badness ensues.
Fixes: ebb5e78cc634 ("MIPS: Initial implementation of a VDSO") Signed-off-by: James Hogan <james.hogan@imgtec.com> Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14229/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the possibility of a deadlock when bringing up
secondary CPUs.
The deadlock occurs because the set_cpu_online() is called before
synchronise_count_slave(). This can cause a deadlock if the boot CPU,
having scheduled another thread, attempts to send an IPI to the
secondary CPU, which it sees has been marked online. The secondary is
blocked in synchronise_count_slave() waiting for the boot CPU to enter
synchronise_count_master(), but the boot cpu is blocked in
smp_call_function_many() waiting for the secondary to respond to it's
IPI request.
Fix this by marking the CPU online in cpu_callin_map and synchronising
counters before declaring the CPU online and calculating the maps for
IPIs.
In the mipsr2_decoder() function, used to emulate pre-MIPSr6
instructions that were removed in MIPSr6, the init_fpu() function is
called if a removed pre-MIPSr6 floating point instruction is the first
floating point instruction used by the task. However, init_fpu()
performs varous actions that rely upon not being migrated. For example
in the most basic case it sets the coprocessor 0 Status.CU1 bit to
enable the FPU & then loads FP register context into the FPU registers.
If the task were to migrate during this time, it may end up attempting
to load FP register context on a different CPU where it hasn't set the
CU1 bit, leading to errors such as:
If the i2c device is already runtime suspended, if qup_i2c_suspend is
executed during suspend-to-idle or suspend-to-ram it will result in the
following splat:
CPU: 3 PID: 1593 Comm: bash Tainted: G W 4.8.0-rc3 #14
Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT)
PC is at clk_core_unprepare+0x80/0x90
LR is at clk_unprepare+0x28/0x40
pc : [<ffff0000086eecf0>] lr : [<ffff0000086f0c58>] pstate: 60000145
Call trace:
clk_core_unprepare+0x80/0x90
qup_i2c_disable_clocks+0x2c/0x68
qup_i2c_suspend+0x10/0x20
platform_pm_suspend+0x24/0x68
...
This patch fixes the issue by executing qup_i2c_pm_suspend_runtime
conditionally in qup_i2c_suspend.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Reviewed-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Wolfram Sang <wsa@the-dreams.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the eg20t driver call request_irq() function before the pch_base_address,
base address of i2c controller's register, is assigned an effective value.
there is one possible scenario that an interrupt which isn't inside eg20t
arrives immediately after request_irq() is executed when i2c controller
shares an interrupt number with others. since the interrupt handler
pch_i2c_handler() has already active as shared action, it will be called
and read its own register to determine if this interrupt is from itself.
At that moment, since base address of i2c registers is not remapped
in kernel space yet,so the INT handler will access an illegal address
and then a error occurs.
Since the device hierarchy domain was added by commit c98c1822ee13
("irqchip/mips-gic: Add device hierarchy domain"), GIC local interrupts
have been broken.
Users attempting to setup a per-cpu local IRQ, for example the GIC timer
clock events code in drivers/clocksource/mips-gic-timer.c, the
setup_percpu_irq function would refuse with -EINVAL because the GIC
irqchip driver never called irq_set_percpu_devid so the
IRQ_PER_CPU_DEVID flag was never set for the IRQ. This happens because
irq_set_percpu_devid was being called from the gic_irq_domain_map
function which is no longer called.
Doing only that runs into further problems because gic_dev_domain_alloc
set the struct irq_chip for all interrupts, local or shared, to
gic_level_irq_controller despite that only being suitable for shared
interrupts. The typical outcome of this is that gic_level_irq_controller
callback functions are called for local interrupts, and then hwirq
number calculations overflow & the driver ends up attempting to access
some invalid register with an address calculated from an invalid hwirq
number. Best case scenario is that this then leads to a bus error. This
is fixed by abstracting the setup of the hwirq & chip to a new function
gic_setup_dev_chip which is used by both the root GIC IRQ domain & the
device domain.
Finally, decoding local interrupts failed because gic_dev_domain_alloc
only called irq_domain_alloc_irqs_parent for shared interrupts. Local
ones were therefore never associated with hwirqs in the root GIC IRQ
domain and the virq in gic_handle_local_int would always be 0. This is
fixed by calling irq_domain_alloc_irqs_parent unconditionally & having
gic_irq_domain_alloc handle both local & shared interrupts, which is
easy due to the aforementioned abstraction of chip setup into
gic_setup_dev_chip.
This fixes use of the MIPS GIC timer for clock events, which has been
broken since c98c1822ee13 ("irqchip/mips-gic: Add device hierarchy
domain") but hadn't been noticed due to a silent fallback to the MIPS
coprocessor 0 count/compare clock events device.
Fixes: c98c1822ee13 ("irqchip/mips-gic: Add device hierarchy domain") Signed-off-by: Paul Burton <paul.burton@imgtec.com> Cc: linux-mips@linux-mips.org Cc: Jason Cooper <jason@lakedaemon.net> Cc: Qais Yousef <qsyousef@gmail.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Link: http://lkml.kernel.org/r/20160913165335.31389-1-paul.burton@imgtec.com Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Waiman reported that booting with CONFIG_EFI_MIXED enabled on his
multi-terabyte HP machine results in boot crashes, because the EFI
region mapping functions loop forever while trying to map those
regions describing RAM.
While this patch doesn't fix the underlying hang, there's really no
reason to map EFI_CONVENTIONAL_MEMORY regions into the EFI page tables
when mixed-mode is not in use at runtime.
If the subvol/snapshot create/destroy ioctls are passed a regular file
with execute permissions set, we'll eventually Oops while trying to do
inode->i_op->lookup via lookup_one_len.
This patch ensures that the file descriptor refers to a directory.
Due to an apparent copy/paste bug, the number of counters for the
beacon configuration were checked twice, instead of checking the
number of probe response counters. Fix this to check the number of
probe response counters before parsing those.
Fixes: 9a774c78e211 ("cfg80211: Support multiple CSA counters") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Off-channel action frames (such as ANQP frames) must be sent either on
the AUX queue or on the offchannel queue, otherwise the firmware will
cause a SYSASSERT.
In the current implementation, the queue to be used is correctly set in
the original skb, but this is done after it is copied. Thus the copy
remains with the original, incorrect queue.
Fix this by setting the queue in the original skb before copying it.
Fixes: commit 5c08b0f5026f ("iwlwifi: mvm: don't override the rate with the AMSDU len") Signed-off-by: Beni Lev <beni.lev@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configure the transmitter delay register at +0x1c to correctly handle
the CAN FD bitrate switch (BRS). This moves the SSP (secondary sample
point) to a proper offset, so that the TDC mechanism works and won't
generate error frames on the CAN link.
Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marc Kleine-Budde <mkl@pengutronix.de> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Oliver Hartkopp <socketcan@hartkopp.net> Cc: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason for this suspend error is because when the CAN interface is not
active the clocks are disabled and then flexcan_chip_enable() will
always fail due to a timeout error.
In order to fix this issue, only call flexcan_chip_enable/disable()
when the CAN interface is active.
Based on a patch from Dong Aisheng in the NXP kernel.
init_tlb_ubc() looked unnecessary to me: tlb_ubc is statically
initialized with zeroes in the init_task, and copied from parent to
child while it is quiescent in arch_dup_task_struct(); so I went to
delete it.
But inserted temporary debug WARN_ONs in place of init_tlb_ubc() to
check that it was always empty at that point, and found them firing:
because memcg reclaim can recurse into global reclaim (when allocating
biosets for swapout in my case), and arrive back at the init_tlb_ubc()
in shrink_node_memcg().
Resetting tlb_ubc.flush_required at that point is wrong: if the upper
level needs a deferred TLB flush, but the lower level turns out not to,
we miss a TLB flush. But fortunately, that's the only part of the
protocol that does not nest: with the initialization removed, cpumask
collects bits from upper and lower levels, and flushes TLB when needed.
Fixes: 72b252aed506 ("mm: send one IPI per CPU to TLB flush all entries after unmapping pages") Signed-off-by: Hugh Dickins <hughd@google.com> Acked-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iter->seq can be reset outside the protection of the mutex. So can
reading of user data. Move the mutex up to the beginning of the function.
Fixes: d7350c3f45694 ("tracing/core: make the read callbacks reentrants") Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since mac80211 doesn't currently support TSIDs 8-15 which can
only be used after QoS TSPEC negotiation (and not even after
WMM negotiation), reject attempts to set up aggregation
sessions for them, which might confuse drivers. In mac80211
we do correctly handle that, but the TSIDs should never get
used anyway, and drivers might not be able to handle it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reset value of weekday is 0x1. This is wrong since
the reset values of the day/month/year make up to Jan 1 2001.
When computed weekday comes out to be Monday. On a scale
of 1-7(Sunday - Saturday) it should be 0x2. So we should not
be relying on the reset value.
Hence compute the wday using the current date/month/year values.
Check if reset wday is any different from the computed wday,
If different then set the wday which we computed using
date/month/year values.
Prior to commit 6c96f05c8bb8 ("reset: Make [of_]reset_control_get[_foo]
functions wrappers"), the "optional" functions returned -ENOTSUPP when
CONFIG_RESET_CONTROLLER was not set.
Revert back to the old behavior by changing the new
__devm_reset_control_get() and __of_reset_control_get() functions to
return ERR_PTR(-ENOTSUPP) when compiled without CONFIG_RESET_CONTROLLER.
Otherwise they will return -EINVAL causing users to think that an error
occurred when CONFIG_RESET_CONTROLLER is not set.
Fixes: 6c96f05c8bb8 ("reset: Make [of_]reset_control_get[_foo] functions wrappers") Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In stm_unlock(), the test to determine whether we've fully unlocked the
flash checks for the lock length to be equal to the flash size. That is
a typo/think-o -- the condition actually means the flash is completely
*locked.* We should be using the inverse condition -- that the lock
length is 0 (i.e., no protection).
The result of this bug is that we never actually turn off the Status
Register Write Disable bit, even if the flash is completely unlocked.
Now we can.
Fixes: 47b8edbf0d43 ("mtd: spi-nor: disallow further writes to SR if WP# is low") Reported-by: Giorgio <giorgio.nicole@arcor.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a cut and paste issue here. The bug is that we are allocating
more memory than necessary for msp_maps. We should be allocating enough
space for a map_info struct (144 bytes) but we instead allocate enough
for an mtd_info struct (1840 bytes). It's a small waste.
The other part of this is not harmful but when we allocated msp_flash
then we allocated enough space fro a map_info pointer instead of an
mtd_info pointer. But since pointers are the same size it works out
fine.
Anyway, I decided to clean up all three allocations a bit to make them
a bit more consistent and clear.
Fixes: 68aa0fa87f6d ('[MTD] PMC MSP71xx flash/rootfs mappings') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a regression accessing the OOB area from the mxc_nand
driver due to an Obiwan error in the mxc_nand_v[12]_ooblayout_free()
functions. They report a bogus oobregion { 64, 7 } which leads to
errors accessing bogus data when reading the oob area.
Prior to the commit the mtd-oobtest module could be run without any
errors. With the offending commit, this test fails with results like:
|Running mtd-oobtest
|
|=================================================
|mtd_oobtest: MTD device: 5
|mtd_oobtest: MTD device size 524288, eraseblock size 131072, page size 2048, count of eraseblocks 4, pages per eraseblock 64, OOB size 64
|mtd_test: scanning for bad eraseblocks
|mtd_test: scanned 4 eraseblocks, 0 are bad
|mtd_oobtest: test 1 of 5
|mtd_oobtest: writing OOBs of whole device
|mtd_oobtest: written up to eraseblock 0
|mtd_oobtest: written 4 eraseblocks
|mtd_oobtest: verifying all eraseblocks
|mtd_oobtest: error @addr[0x0:0x19] 0x9a -> 0x78 diff 0xe2
|mtd_oobtest: error @addr[0x0:0x1a] 0xcc -> 0x0 diff 0xcc
|mtd_oobtest: error @addr[0x0:0x1b] 0xe0 -> 0x85 diff 0x65
|mtd_oobtest: error @addr[0x0:0x1c] 0x60 -> 0x62 diff 0x2
|mtd_oobtest: error @addr[0x0:0x1d] 0x69 -> 0x45 diff 0x2c
|mtd_oobtest: error @addr[0x0:0x1e] 0xcd -> 0xa0 diff 0x6d
|mtd_oobtest: error @addr[0x0:0x1f] 0xf2 -> 0x60 diff 0x92
|mtd_oobtest: error: verify failed at 0x0
[...]
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de> Fixes: a894cf6c5a82 ("mtd: nand: mxc: switch to mtd_ooblayout_ops") Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The wq_numa_init() function makes a private CPU to node map by calling
cpu_to_node() early in the boot process, before the non-boot CPUs are
brought online. Since the default implementation of cpu_to_node()
returns zero for CPUs that have never been brought online, the
workqueue system's view is that *all* CPUs are on node zero.
When the unbound workqueue for a non-zero node is created, the
tsk_cpus_allowed() for the worker threads is the empty set because
there are, in the view of the workqueue system, no CPUs on non-zero
nodes. The code in try_to_wake_up() using this empty cpumask ends up
using the cpumask empty set value of NR_CPUS as an index into the
per-CPU area pointer array, and gets garbage as it is one past the end
of the array. This results in:
Fix by moving call to numa_store_cpu_info() for all CPUs into
smp_prepare_cpus(), which happens before wq_numa_init(). Since
smp_store_cpu_info() now contains only a single function call,
simplify by removing the function and out-lining its contents.
Suggested-by: Robert Richter <rric@kernel.org> Fixes: 1a2db300348b ("arm64, numa: Add NUMA support for arm64 platforms.") Signed-off-by: David Daney <david.daney@cavium.com> Reviewed-by: Robert Richter <rrichter@cavium.com> Tested-by: Yisheng Xie <xieyisheng1@huawei.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switching iov_iter fault-in to multipages variants has exposed an old
bug in underlying fault_in_multipages_...(); they break if the range
passed to them wraps around. Normally access_ok() done by callers will
prevent such (and it's a guaranteed EFAULT - ERR_PTR() values fall into
such a range and they should not point to any valid objects).
However, on architectures where userland and kernel live in different
MMU contexts (e.g. s390) access_ok() is a no-op and on those a range
with a wraparound can reach fault_in_multipages_...().
Since any wraparound means EFAULT there, the fix is trivial - turn
those
while (uaddr <= end)
...
into
if (unlikely(uaddr > end))
return -EFAULT;
do
...
while (uaddr <= end);
Reported-by: Jan Stancek <jstancek@redhat.com> Tested-by: Jan Stancek <jstancek@redhat.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a socket is cloned, the associated sock_cgroup_data is duplicated
but not its reference on the cgroup. As a result, the cgroup reference
count will underflow when both sockets are destroyed later on.
Fixes: bd1060a1d671 ("sock, cgroup: add sock->sk_cgroup") Link: http://lkml.kernel.org/r/20160914194846.11153-2-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Tejun Heo <tj@kernel.org> Cc: Michal Hocko <mhocko@suse.cz> Cc: Vladimir Davydov <vdavydov@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During cgroup2 rollout into production, we started encountering css
refcount underflows and css access crashes in the memory controller.
Splitting the heavily shared css reference counter into logical users
narrowed the imbalance down to the cgroup2 socket memory accounting.
The problem turns out to be the per-cpu charge cache. Cgroup1 had a
separate socket counter, but the new cgroup2 socket accounting goes
through the common charge path that uses a shared per-cpu cache for all
memory that is being tracked. Those caches are safe against scheduling
preemption, but not against interrupts - such as the newly added packet
receive path. When cache draining is interrupted by network RX taking
pages out of the cache, the resuming drain operation will put references
of in-use pages, thus causing the imbalance.
Disable IRQs during all per-cpu charge cache operations.
Fixes: f7e1cb6ec51b ("mm: memcontrol: account socket memory in unified hierarchy memory controller") Link: http://lkml.kernel.org/r/20160914194846.11153-1-hannes@cmpxchg.org Signed-off-by: Johannes Weiner <hannes@cmpxchg.org> Acked-by: Tejun Heo <tj@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Michal Hocko <mhocko@suse.cz> Cc: Vladimir Davydov <vdavydov@virtuozzo.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fanotify_get_response() calls fsnotify_remove_event() when it finds that
group is being released from fanotify_release() (bypass_perm is set).
However the event it removes need not be only in the group's notification
queue but it can have already moved to access_list (userspace read the
event before closing the fanotify instance fd) which is protected by a
different lock. Thus when fsnotify_remove_event() races with
fanotify_release() operating on access_list, the list can get corrupted.
Fix the problem by moving all the logic removing permission events from
the lists to one place - fanotify_release().
Fixes: 5838d4442bd5 ("fanotify: fix double free of pending permission events") Link: http://lkml.kernel.org/r/1473797711-14111-3-git-send-email-jack@suse.cz Signed-off-by: Jan Kara <jack@suse.cz> Reported-by: Miklos Szeredi <mszeredi@redhat.com> Tested-by: Miklos Szeredi <mszeredi@redhat.com> Reviewed-by: Miklos Szeredi <mszeredi@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 62c230bc1790 ("mm: add support for a filesystem to activate
swap files and use direct_IO for writing swap pages") replaced the
swap_aops dirty hook from __set_page_dirty_no_writeback() with
swap_set_page_dirty().
For normal cases without these special SWP flags code path falls back to
__set_page_dirty_no_writeback() so the behaviour is expected to be the
same as before.
But swap_set_page_dirty() makes use of the page_swap_info() helper to
get the swap_info_struct to check for the flags like SWP_FILE,
SWP_BLKDEV etc as desired for those features. This helper has
BUG_ON(!PageSwapCache(page)) which is racy and safe only for the
set_page_dirty_lock() path.
For the set_page_dirty() path which is often needed for cases to be
called from irq context, kswapd() can toggle the flag behind the back
while the call is getting executed when system is low on memory and
heavy swapping is ongoing.
This ends up with undesired kernel panic.
This patch just moves the check outside the helper to its users
appropriately to fix kernel panic for the described path. Couple of
users of helpers already take care of SwapCache condition so I skipped
them.
Link: http://lkml.kernel.org/r/1473460718-31013-1-git-send-email-santosh.shilimkar@oracle.com Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Joe Perches <joe@perches.com> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Cc: Rik van Riel <riel@redhat.com> Cc: David S. Miller <davem@davemloft.net> Cc: Jens Axboe <axboe@fb.com> Cc: Michal Hocko <mhocko@suse.com> Cc: Hugh Dickins <hughd@google.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xfs_wait_buftarg() waits for all pending I/O, drains the ioend
completion workqueue and walks the LRU until all buffers in the cache
have been released. This is traditionally an unmount operation` but the
mechanism is also reused during filesystem freeze.
xfs_wait_buftarg() invokes drain_workqueue() as part of the quiesce,
which is intended more for a shutdown sequence in that it indicates to
the queue that new operations are not expected once the drain has begun.
New work jobs after this point result in a WARN_ON_ONCE() and are
otherwise dropped.
With filesystem freeze, however, read operations are allowed and can
proceed during or after the workqueue drain. If such a read occurs
during the drain sequence, the workqueue infrastructure complains about
the queued ioend completion work item and drops it on the floor. As a
result, the buffer remains on the LRU and the freeze never completes.
Despite the fact that the overall buffer cache cleanup is not necessary
during freeze, fix up this operation such that it is safe to invoke
during non-unmount quiesce operations. Replace the drain_workqueue()
call with flush_workqueue(), which runs a similar serialization on
pending workqueue jobs without causing new jobs to be dropped. This is
safe for unmount as unmount independently locks out new operations by
the time xfs_wait_buftarg() is invoked.
cc: <stable@vger.kernel.org> Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Dave Chinner <david@fromorbit.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the latest gcc compilers, they give a warning if
__builtin_return_address() parameter is greater than 0. That is because if
it is used by a function called by a top level function (or in the case of
the kernel, by assembly), it can try to access stack frames outside the
stack and crash the system.
The tracing system uses __builtin_return_address() of up to 2! But it is
well aware of the dangers that it may have, and has even added precautions
to protect against it (see the thunk code in arch/x86/entry/thunk*.S)
Linus originally added KBUILD_CFLAGS that would suppress the warning for the
entire kernel, as simply adding KBUILD_CFLAGS to the tracing directory
wouldn't work. The tracing directory plays a bit with the CFLAGS and
requires a little more logic.
This adds that special logic to only suppress the warning for the tracing
directory. If it is used anywhere else outside of tracing, the warning will
still be triggered.
Newer versions of gcc warn about the use of __builtin_return_address()
with a non-zero argument when "-Wall" is specified:
kernel/trace/trace_irqsoff.c: In function ‘stop_critical_timings’:
kernel/trace/trace_irqsoff.c:433:86: warning: calling ‘__builtin_return_address’ with a nonzero argument is unsafe [-Wframe-address]
stop_critical_timing(CALLER_ADDR0, CALLER_ADDR1);
[ .. repeats a few times for other similar cases .. ]
It is true that a non-zero argument is somewhat dangerous, and we do not
actually have very many uses of that in the kernel - but the ftrace code
does use it, and as Stephen Rostedt says:
"We are well aware of the danger of using __builtin_return_address() of
> 0. In fact that's part of the reason for having the "thunk" code in
x86 (See arch/x86/entry/thunk_{64,32}.S). [..] it adds extra frames
when tracking irqs off sections, to prevent __builtin_return_address()
from accessing bad areas. In fact the thunk_32.S states: 'Trampoline to
trace irqs off. (otherwise CALLER_ADDR1 might crash)'."
For now, __builtin_return_address() with a non-zero argument is the best
we can do, and the warning is not helpful and can end up making people
miss other warnings for real problems.
So disable the frame-address warning on compilers that need it.
Several build configurations had already disabled this warning because
it generates a lot of false positives. But some had not, and it was
still enabled for "allmodconfig" builds, for example.
Looking at the warnings produced, every single one I looked at was a
false positive, and the warnings are frequent enough (and big enough)
that they can easily hide real problems that you don't notice in the
noise generated by -Wmaybe-uninitialized.
The warning is good in theory, but this is a classic case of a warning
that causes more problems than the warning can solve.
If gcc gets better at avoiding false positives, we may be able to
re-enable this warning. But as is, we're better off without it, and I
want to be able to see the *real* warnings.
Somewhere along the way the autofs expire operation has changed to hold
a spin lock over expired dentry selection. The autofs indirect mount
expired dentry selection is complicated and quite lengthy so it isn't
appropriate to hold a spin lock over the operation.
Commit 47be61845c77 ("fs/dcache.c: avoid soft-lockup in dput()") added a
might_sleep() to dput() causing a WARN_ONCE() about this usage to be
issued.
But the spin lock doesn't need to be held over this check, the autofs
dentry info. flags are enough to block walks into dentrys during the
expire.
I've left the direct mount expire as it is (for now) because it is much
simpler and quicker than the indirect mount expire and adding spin lock
release and re-aquires would do nothing more than add overhead.
Fixes: 47be61845c77 ("fs/dcache.c: avoid soft-lockup in dput()") Link: http://lkml.kernel.org/r/20160912014017.1773.73060.stgit@pluto.themaw.net Signed-off-by: Ian Kent <raven@themaw.net> Reported-by: Takashi Iwai <tiwai@suse.de> Tested-by: Takashi Iwai <tiwai@suse.de> Cc: Takashi Iwai <tiwai@suse.de> Cc: NeilBrown <neilb@suse.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 38b52efd218b ("ocfs2: bump up o2cb network protocol
version").
This commit made rolling upgrade fail. When one node is upgraded to new
version with this commit, the remaining nodes will fail to establish
connections to it, then the application like VMs on the remaining nodes
can't be live migrated to the upgraded one. This will cause an outage.
Since negotiate hb timeout behavior didn't change without this commit,
so revert it.
Fixes: 38b52efd218bf ("ocfs2: bump up o2cb network protocol version") Link: http://lkml.kernel.org/r/1471396924-10375-1-git-send-email-junxiao.bi@oracle.com Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <joseph.qi@huawei.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we punch a hole on a reflink such that following conditions are met:
1. start offset is on a cluster boundary
2. end offset is not on a cluster boundary
3. (end offset is somewhere in another extent) or
(hole range > MAX_CONTIG_BYTES(1MB)),
we dont COW the first cluster starting at the start offset. But in this
case, we were wrongly passing this cluster to
ocfs2_zero_range_for_truncate() to zero out. This will modify the
cluster in place and zero it in the source too.
Fix this by skipping this cluster in such a scenario.
To reproduce:
1. Create a random file of say 10 MB
xfs_io -c 'pwrite -b 4k 0 10M' -f 10MBfile
2. Reflink it
reflink -f 10MBfile reflnktest
3. Punch a hole at starting at cluster boundary with range greater that
1MB. You can also use a range that will put the end offset in another
extent.
fallocate -p -o 0 -l 1048615 reflnktest
4. sync
5. Check the first cluster in the source file. (It will be zeroed out).
dd if=10MBfile iflag=direct bs=<cluster size> count=1 | hexdump -C
Link: http://lkml.kernel.org/r/1470957147-14185-1-git-send-email-ashish.samant@oracle.com Signed-off-by: Ashish Samant <ashish.samant@oracle.com> Reported-by: Saar Maoz <saar.maoz@oracle.com> Reviewed-by: Srinivas Eeda <srinivas.eeda@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Joseph Qi <joseph.qi@huawei.com> Cc: Eric Ren <zren@suse.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ac7cf246dfdb ("ocfs2/dlm: fix race between convert and recovery")
checks if lockres master has changed to identify whether new master has
finished recovery or not. This will introduce a race that right after
old master does umount ( means master will change), a new convert
request comes.
In this case, it will reset lockres state to DLM_RECOVERING and then
retry convert, and then fail with lockres->l_action being set to
OCFS2_AST_INVALID, which will cause inconsistent lock level between
ocfs2 and dlm, and then finally BUG.
Since dlm recovery will clear lock->convert_pending in
dlm_move_lockres_to_recovery_list, we can use it to correctly identify
the race case between convert and recovery. So fix it.
Fixes: ac7cf246dfdb ("ocfs2/dlm: fix race between convert and recovery") Link: http://lkml.kernel.org/r/57CE1569.8010704@huawei.com Signed-off-by: Joseph Qi <joseph.qi@huawei.com> Signed-off-by: Jun Piao <piaojun@huawei.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current implementation uses a global per-cpu array to store
data which are used to derive the next IV. This is insecure as
the attacker may change the stored data.
This patch removes all traces of chaining and replaces it with
multiplication of the salt and the sequence number.
When we need to allocate a temporary blkcipher_walk_next and it
fails, the code is supposed to take the slow path of processing
the data block by block. However, due to an unrelated change
we instead end up dereferencing the NULL pointer.
This patch fixes it by moving the unrelated bsize setting out
of the way so that we enter the slow path as inteded.
The AES-CTR glue code avoids calling into the blkcipher API for the
tail portion of the walk, by comparing the remainder of walk.nbytes
modulo AES_BLOCK_SIZE with the residual nbytes, and jumping straight
into the tail processing block if they are equal. This tail processing
block checks whether nbytes != 0, and does nothing otherwise.
However, in case of an allocation failure in the blkcipher layer, we
may enter this code with walk.nbytes == 0, while nbytes > 0. In this
case, we should not dereference the source and destination pointers,
since they may be NULL. So instead of checking for nbytes != 0, check
for (walk.nbytes % AES_BLOCK_SIZE) != 0, which implies the former in
non-error conditions.
Fixes: 86464859cc77 ("crypto: arm - AES in ECB/CBC/CTR/XTS modes using ARMv8 Crypto Extensions") Reported-by: xiakaixu <xiakaixu@huawei.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AES-CTR glue code avoids calling into the blkcipher API for the
tail portion of the walk, by comparing the remainder of walk.nbytes
modulo AES_BLOCK_SIZE with the residual nbytes, and jumping straight
into the tail processing block if they are equal. This tail processing
block checks whether nbytes != 0, and does nothing otherwise.
However, in case of an allocation failure in the blkcipher layer, we
may enter this code with walk.nbytes == 0, while nbytes > 0. In this
case, we should not dereference the source and destination pointers,
since they may be NULL. So instead of checking for nbytes != 0, check
for (walk.nbytes % AES_BLOCK_SIZE) != 0, which implies the former in
non-error conditions.
Fixes: 49788fe2a128 ("arm64/crypto: AES-ECB/CBC/CTR/XTS using ARMv8 NEON and Crypto Extensions") Reported-by: xiakaixu <xiakaixu@huawei.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
new_insert_key only makes any sense when it's associated with a
new_insert_ptr, which is initialized to NULL and changed to a
buffer_head when we also initialize new_insert_key. We can key off of
that to avoid the uninitialized warning.
Link: http://lkml.kernel.org/r/5eca5ffb-2155-8df2-b4a2-f162f105efed@suse.com Signed-off-by: Jeff Mahoney <jeffm@suse.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Jan Kara <jack@suse.cz> Cc: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit acb2505d0119 ("openrisc: fix copy_from_user()"),
copy_from_user() returns the number of bytes requested, not the
number of bytes not copied.
arch/avr32/kernel/built-in.o: In function `arch_ptrace':
(.text+0x650): undefined reference to `___copy_from_user'
arch/avr32/kernel/built-in.o:(___ksymtab+___copy_from_user+0x0): undefined
reference to `___copy_from_user'
kernel/built-in.o: In function `proc_doulongvec_ms_jiffies_minmax':
(.text+0x5dd8): undefined reference to `___copy_from_user'
kernel/built-in.o: In function `proc_dointvec_minmax_sysadmin':
sysctl.c:(.text+0x6174): undefined reference to `___copy_from_user'
kernel/built-in.o: In function `ptrace_has_cap':
ptrace.c:(.text+0x69c0): undefined reference to `___copy_from_user'
kernel/built-in.o:ptrace.c:(.text+0x6b90): more undefined references to
`___copy_from_user' follow
Some of our "for_each_xyz()" macro constructs make gcc unhappy about
lack of braces around if-statements inside or outside the loop, because
the loop construct itself has a "if-then-else" statement inside of it.
The resulting warnings look something like this:
drivers/gpu/drm/i915/i915_debugfs.c: In function ‘i915_dump_lrc’:
drivers/gpu/drm/i915/i915_debugfs.c:2103:6: warning: suggest explicit braces to avoid ambiguous ‘else’ [-Wparentheses]
if (ctx != dev_priv->kernel_context)
^
even if the code itself is fine.
Since the warning is fairly easy to avoid by adding a braces around the
if-statement near the for_each_xyz() construct, do so, rather than
disabling the otherwise potentially useful warning.
(The if-then-else statements used in the "for_each_xyz()" constructs are
designed to be inherently safe even with no braces, but in this case
it's quite understandable that gcc isn't really able to tell that).
This finally leaves the standard "allmodconfig" build with just a
handful of remaining warnings, so new and valid warnings hopefully will
stand out.
Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... that should zero on faults. Also remove the <censored> helpful
logics wrt range truncation copied from ppc32. Where it had ever
been needed only in case of copy_from_user() *and* had not been merged
into the mainline until a month after the need had disappeared.
A decade before openrisc went into mainline, I might add...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... in all cases, including the failing access_ok()
Note that some architectures using asm-generic/uaccess.h have
__copy_from_user() not zeroing the tail on failure halfway
through. This variant works either way.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's -EFAULT, not -1 (and contrary to the comment in there,
__strnlen_user() can return 0 - on faults).
Acked-by: Richard Kuo <rkuo@codeaurora.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* copy_from_user() on access_ok() failure ought to zero the destination
* none of those primitives should skip the access_ok() check in case of
small constant size.
It could be done in exception-handling bits in __get_user_b() et.al.,
but the surgery involved would take more knowledge of sh64 details
than I have or _want_ to have.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log