KVM allows userspace to violate consistency checks related to the
guest's CPUID model to some degree. Generally speaking, userspace has
carte blanche when it comes to guest state so long as jamming invalid
state won't negatively affect the host.
Currently this is seems to be a non-issue as most of the interesting
EFER checks are missing, e.g. NX and LME, but those will be added
shortly. Proactively exempt userspace from the CPUID checks so as not
to break userspace.
Note, the efer_reserved_bits check still applies to userspace writes as
that mask reflects the host's capabilities, e.g. KVM shouldn't allow a
guest to run with NX=1 if it has been disabled in the host.
Fixes: d80174745ba39 ("KVM: SVM: Only allow setting of EFER_SVME when CPUID SVM is set") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add patch for realtek codec in Lenovo B50-70 that fixes inverted
internal microphone channel.
Device IdeaPad Y410P has the same PCI SSID as Lenovo B50-70,
but first one is about fix the noise and it didn't seem help in a
later kernel version.
So I replaced IdeaPad Y410P device description with B50-70 and apply
inverted microphone fix.
Unaligned AIO must be serialized because the zeroing of partial blocks
of unaligned AIO can result in data corruption in case it's overlapping
another in flight IO.
Currently we wait for all unwritten extents before we submit unaligned
AIO which protects data in case of unaligned AIO is following overlapping
IO. However if a unaligned AIO is followed by overlapping aligned AIO we
can still end up corrupting data.
To fix this, we must make sure that the unaligned AIO is the only IO in
flight by waiting for unwritten extents conversion not just before the
IO submission, but right after it as well.
This problem can be reproduced by xfstest generic/538
This commit zeroes out the unused memory region in the buffer_head
corresponding to the extent metablock after writing the extent header
and the corresponding extent node entries.
This is done to prevent random uninitialized data from getting into
the filesystem when the extent block is synced.
synchronize_rcu() didn't wait for call_rcu() callbacks, so inode wb
switch may not go to the workqueue after synchronize_rcu(). Thus
previous scheduled switches was not finished even flushing the
workqueue, which will cause a NULL pointer dereferenced followed below.
VFS: Busy inodes after unmount of vdd. Self-destruct in 5 seconds. Have a nice day...
BUG: unable to handle kernel NULL pointer dereference at 0000000000000278
evict+0xb3/0x180
iput+0x1b0/0x230
inode_switch_wbs_work_fn+0x3c0/0x6a0
worker_thread+0x4e/0x490
? process_one_work+0x410/0x410
kthread+0xe6/0x100
ret_from_fork+0x39/0x50
Replace the synchronize_rcu() call with a rcu_barrier() to wait for all
pending callbacks to finish. And inc isw_nr_in_flight after call_rcu()
in inode_switch_wbs() to make more sense.
sync_inodes_sb() can race against cgwb (cgroup writeback) membership
switches and fail to writeback some inodes. For example, if an inode
switches to another wb while sync_inodes_sb() is in progress, the new
wb might not be visible to bdi_split_work_to_wbs() at all or the inode
might jump from a wb which hasn't issued writebacks yet to one which
already has.
This patch adds backing_dev_info->wb_switch_rwsem to synchronize cgwb
switch path against sync_inodes_sb() so that sync_inodes_sb() is
guaranteed to see all the target wbs and inodes can't jump wbs to
escape syncing.
v2: Fixed misplaced rwsem init. Spotted by Jiufei.
fib_rules: fix error in backport of e9919a24d302 ("fib_rules: return 0...")
When commit e9919a24d302 ("fib_rules: return 0 directly if an exactly
same rule exists when NLM_F_EXCL not supplied") was backported to 4.9.y,
it changed the logic a bit as err should have been reset before exiting
the test, like it happens in the original logic.
If this is not set, errors happen :(
Reported-by: Nathan Chancellor <natechancellor@gmail.com> Reported-by: David Ahern <dsahern@gmail.com> Reported-by: Florian Westphal <fw@strlen.de> Cc: Hangbin Liu <liuhangbin@gmail.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
arm32 xts-aes-neonbs doesn't set an alignmask, so currently it isn't
affected by this despite unconditionally accessing walk.iv. However
this is more subtle than desired, and it was actually broken prior to
the alignmask being removed by commit cc477bf64573 ("crypto: arm/aes -
replace bit-sliced OpenSSL NEON code"). Thus, update xts-aes-neonbs to
start checking the return value of skcipher_walk_virt().
Fixes: e4e7f10bfc40 ("ARM: add support for bit sliced AES using NEON instructions") Cc: <stable@vger.kernel.org> # v3.13+ Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user-provided IV needs to be aligned to the algorithm's
alignmask, then skcipher_walk_virt() copies the IV into a new aligned
buffer walk.iv. But skcipher_walk_virt() can fail afterwards, and then
if the caller unconditionally accesses walk.iv, it's a use-after-free.
salsa20-generic doesn't set an alignmask, so currently it isn't affected
by this despite unconditionally accessing walk.iv. However this is more
subtle than desired, and it was actually broken prior to the alignmask
being removed by commit b62b3db76f73 ("crypto: salsa20-generic - cleanup
and convert to skcipher API").
Since salsa20-generic does not update the IV and does not need any IV
alignment, update it to use req->iv instead of walk.iv.
GCM instances can be created by either the "gcm" template, which only
allows choosing the block cipher, e.g. "gcm(aes)"; or by "gcm_base",
which allows choosing the ctr and ghash implementations, e.g.
"gcm_base(ctr(aes-generic),ghash-generic)".
However, a "gcm_base" instance prevents a "gcm" instance from being
registered using the same implementations. Nor will the instance be
found by lookups of "gcm". This can be used as a denial of service.
Moreover, "gcm_base" instances are never tested by the crypto
self-tests, even if there are compatible "gcm" tests.
The root cause of these problems is that instances of the two templates
use different cra_names. Therefore, fix these problems by making
"gcm_base" instances set the same cra_name as "gcm" instances, e.g.
"gcm(aes)" instead of "gcm_base(ctr(aes-generic),ghash-generic)".
This requires extracting the block cipher name from the name of the ctr
algorithm. It also requires starting to verify that the algorithms are
really ctr and ghash, not something else entirely. But it would be
bizarre if anyone were actually using non-gcm-compatible algorithms with
gcm_base, so this shouldn't break anyone in practice.
According to ipmi spec, block number is a number that is incremented,
starting with 0, for each new block of message data returned using the
middle transaction.
Here, the 'blocknum' is data[0] which always starts from zero(0) and
'ssif_info->multi_pos' starts from 1.
So, we need to add +1 to blocknum while comparing with multi_pos.
In journal_reclaim() ja->cur_idx of each cache will be update to
reclaim available journal buckets. Variable 'int n' is used to count how
many cache is successfully reclaimed, then n is set to c->journal.key
by SET_KEY_PTRS(). Later in journal_write_unlocked(), a for_each_cache()
loop will write the jset data onto each cache.
The problem is, if all jouranl buckets on each cache is full, the
following code in journal_reclaim(),
529 for_each_cache(ca, c, iter) {
530 struct journal_device *ja = &ca->journal;
531 unsigned int next = (ja->cur_idx + 1) % ca->sb.njournal_buckets;
532
533 /* No space available on this device */
534 if (next == ja->discard_idx)
535 continue;
536
537 ja->cur_idx = next;
538 k->ptr[n++] = MAKE_PTR(0,
539 bucket_to_sector(c, ca->sb.d[ja->cur_idx]),
540 ca->sb.nr_this_dev);
541 }
542
543 bkey_init(k);
544 SET_KEY_PTRS(k, n);
If there is no available bucket to reclaim, the if() condition at line
534 will always true, and n remains 0. Then at line 544, SET_KEY_PTRS()
will set KEY_PTRS field of c->journal.key to 0.
Setting KEY_PTRS field of c->journal.key to 0 is wrong. Because in
journal_write_unlocked() the journal data is written in following loop,
649 for (i = 0; i < KEY_PTRS(k); i++) {
650-671 submit journal data to cache device
672 }
If KEY_PTRS field is set to 0 in jouranl_reclaim(), the journal data
won't be written to cache device here. If system crahed or rebooted
before bkeys of the lost journal entries written into btree nodes, data
corruption will be reported during bcache reload after rebooting the
system.
Indeed there is only one cache in a cache set, there is no need to set
KEY_PTRS field in journal_reclaim() at all. But in order to keep the
for_each_cache() logic consistent for now, this patch fixes the above
problem by not setting 0 KEY_PTRS of journal key, if there is no bucket
available to reclaim.
Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Cc: stable@vger.kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a race between cache device register and cache set unregister.
For an already registered cache device, register_bcache will call
bch_is_open to iterate through all cachesets and check every cache
there. The race occurs if cache_set_free executes at the same time and
clears the caches right before ca is dereferenced in bch_is_open_cache.
To close the race, let's make sure the clean up work is protected by
the bch_register_lock as well.
This issue can be reproduced as follows,
while true; do echo /dev/XXX> /sys/fs/bcache/register ; done&
while true; do echo 1> /sys/block/XXX/bcache/set/unregister ; done &
When finding out which inodes have references on a particular extent, done
by backref.c:iterate_extent_inodes(), from the BTRFS_IOC_LOGICAL_INO (both
v1 and v2) ioctl and from scrub we use the transaction join API to grab a
reference on the currently running transaction, since in order to give
accurate results we need to inspect the delayed references of the currently
running transaction.
However, if there is currently no running transaction, the join operation
will create a new transaction. This is inefficient as the transaction will
eventually be committed, doing unnecessary IO and introducing a potential
point of failure that will lead to a transaction abort due to -ENOSPC, as
recently reported [1].
That's because the join, creates the transaction but does not reserve any
space, so when attempting to update the root item of the root passed to
btrfs_join_transaction(), during the transaction commit, we can end up
failling with -ENOSPC. Users of a join operation are supposed to actually
do some filesystem changes and reserve space by some means, which is not
the case of iterate_extent_inodes(), it is a read-only operation for all
contextes from which it is called.
The reported [1] -ENOSPC failure stack trace is the following:
Instead of removing EXT4_MOUNT_JOURNAL_CHECKSUM from s_def_mount_opt as
I assume was intended, all other options were blown away leading to
_ext4_show_options() output being incorrect.
Fixes: 1e381f60dad9 ("ext4: do not allow journal_opts for fs w/o journal") Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We hit a BUG at fs/buffer.c:3057 if we detached the nbd device
before unmounting ext4 filesystem.
The typical chain of events leading to the BUG:
jbd2_write_superblock
submit_bh
submit_bh_wbc
BUG_ON(!buffer_mapped(bh));
The block device is removed and all the pages are invalidated. JBD2
was trying to write journal superblock to the block device which is
no longer present.
Fix this by checking the journal superblock's buffer head prior to
submitting.
Reported-by: Eric Ren <renzhen@linux.alibaba.com> Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Cc: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bug manifests on systemd systems with multiple vtcon devices:
# cat /sys/devices/virtual/vtconsole/vtcon0/name
(S) dummy device
# cat /sys/devices/virtual/vtconsole/vtcon1/name
(M) frame buffer device
There systemd runs 'loadkeys' tool in tapallel for each vtcon
instance. This causes two parallel ioctl(KDSKBSENT) calls to
race into adding the same entry into 'func_table' array at:
drivers/tty/vt/keyboard.c:vt_do_kdgkb_ioctl()
The function has no locking around writes to 'func_table'.
The simplest reproducer is to have initrams with the following
init on a 8-CPU machine x86_64:
Mismatch between what is found in the Datasheets for DA9063 and DA9063L
provided by Dialog Semiconductor, and the register names provided in the
MFD registers file. The changes are for the OTP (one-time-programming)
control registers. The two naming errors are OPT instead of OTP, and
COUNT instead of CONT (i.e. control).
Cc: Stable <stable@vger.kernel.org> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases, ocfs2_iget() reads the data of inode, which has been
deleted for some reason. That will make the system panic. So We should
judge whether this inode has been deleted, and tell the caller that the
inode is a bad inode.
For example, the ocfs2 is used as the backed of nfs, and the client is
nfsv3. This issue can be reproduced by the following steps.
on the nfs server side,
..../patha/pathb
Step 1: The process A was scheduled before calling the function fh_verify.
Step 2: The process B is removing the 'pathb', and just completed the call
to function dput. Then the dentry of 'pathb' has been deleted from the
dcache, and all ancestors have been deleted also. The relationship of
dentry and inode was deleted through the function hlist_del_init. The
following is the call stack.
dentry_iput->hlist_del_init(&dentry->d_u.d_alias)
At this time, the inode is still in the dcache.
Step 3: The process A call the function ocfs2_get_dentry, which get the
inode from dcache. Then the refcount of inode is 1. The following is the
call stack.
nfsd3_proc_getacl->fh_verify->exportfs_decode_fh->fh_to_dentry(ocfs2_get_dentry)
Step 4: Dirty pages are flushed by bdi threads. So the inode of 'patha'
is evicted, and this directory was deleted. But the inode of 'pathb'
can't be evicted, because the refcount of the inode was 1.
Step 5: The process A keep running, and call the function
reconnect_path(in exportfs_decode_fh), which call function
ocfs2_get_parent of ocfs2. Get the block number of parent
directory(patha) by the name of ... Then read the data from disk by the
block number. But this inode has been deleted, so the system panic.
Process A Process B
1. in nfsd3_proc_getacl |
2. | dput
3. fh_to_dentry(ocfs2_get_dentry) |
4. bdi flush dirty cache |
5. ocfs2_iget |
[283465.542049] OCFS2: ERROR (device sdp): ocfs2_validate_inode_block:
Invalid dinode #580640: OCFS2_VALID_FL not set
[283465.545490] Kernel panic - not syncing: OCFS2: (device sdp): panic forced
after error
The semantics of what mincore() considers to be resident is not
completely clear, but Linux has always (since 2.3.52, which is when
mincore() was initially done) treated it as "page is available in page
cache".
That's potentially a problem, as that [in]directly exposes
meta-information about pagecache / memory mapping state even about
memory not strictly belonging to the process executing the syscall,
opening possibilities for sidechannel attacks.
Change the semantics of mincore() so that it only reveals pagecache
information for non-anonymous mappings that belog to files that the
calling process could (if it tried to) successfully open for writing;
otherwise we'd be including shared non-exclusive mappings, which
- is the sidechannel
- is not the usecase for mincore(), as that's primarily used for data,
not (shared) text
[jkosina@suse.cz: v2] Link: http://lkml.kernel.org/r/20190312141708.6652-2-vbabka@suse.cz
[mhocko@suse.com: restructure can_do_mincore() conditions] Link: http://lkml.kernel.org/r/nycvar.YFH.7.76.1903062342020.19912@cbobk.fhfr.pm Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Vlastimil Babka <vbabka@suse.cz> Acked-by: Josh Snyder <joshs@netflix.com> Acked-by: Michal Hocko <mhocko@suse.com> Originally-by: Linus Torvalds <torvalds@linux-foundation.org> Originally-by: Dominique Martinet <asmadeus@codewreck.org> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Dave Chinner <david@fromorbit.com> Cc: Kevin Easton <kevin@guarana.org> Cc: Matthew Wilcox <willy@infradead.org> Cc: Cyril Hrubis <chrubis@suse.cz> Cc: Tejun Heo <tj@kernel.org> Cc: Kirill A. Shutemov <kirill@shutemov.name> Cc: Daniel Gruss <daniel@gruss.cc> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current algorithm allows 3 types of transfers, 16bit, 32bit and
burst. According to Realtek, 16bit transfers have a special restriction
in that it is restricted to the memory region of
0x18020000 ~ 0x18021000. This region is the memory location of the I2C
registers. The current algorithm does not uphold this restriction and
therefore fails to complete writes.
Since this has been broken for some time it likely no one is using it.
Better to simply disable the 16 bit writes. This will allow users to
properly load firmware over SPI without data corruption.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org> Reviewed-by: Ben Zhang <benzh@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The max98090 driver defines 3 DAPM muxes; one for the right line output
(LINMOD Mux), one for the left headphone mixer source (MIXHPLSEL Mux)
and one for the right headphone mixer source (MIXHPRSEL Mux). The same
bit is used for the mux as well as the DAPM enable, and although the mux
can be correctly configured, after playback has completed, the mux will
be reset during the disable phase. This is preventing the state of these
muxes from being saved and restored correctly on system reboot. Fix this
by marking these muxes as SND_SOC_NOPM.
Note this has been verified this on the Tegra124 Nyan Big which features
the MAX98090 codec.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ NOTE: This change is supposed to reduce the possible click noises at
(runtime) PM resume. The functionality should be same (i.e. the
verbs are executed correctly) no matter which order is, so this
should be safe to apply for all codecs -- tiwai ]
On the machines with AMD GPU or Nvidia GPU, we often meet this issue:
after s3, there are 4 HDMI/DP audio devices in the gnome-sound-setting
even there is no any monitors plugged.
When this problem happens, we check the /proc/asound/cardX/eld#N.M, we
will find the monitor_present=1, eld_valid=0.
The root cause is BIOS or GPU driver makes the PRESENCE valid even no
monitor plugged, and of course the driver will not get the valid
eld_data subsequently.
In this situation, we should not report the jack_plugged event, to do
so, let us change the function hdmi_present_sense_via_verbs(). In this
function, it reads the pin_sense via snd_hda_pin_sense(), after
calling this function, the jack_dirty is 0, and before exiting
via_verbs(), we change the shadow pin_sense according to both
monitor_present and eld_valid, then in the snd_hda_jack_report_sync(),
since the jack_dirty is still 0, it will report jack event according
to this modified shadow pin_sense.
After this change, the driver will not report Jack_is_plugged event
through hdmi_present_sense_via_verbs() if monitor_present is 1 and
eld_valid is 0.
The driver will check the monitor presence when resuming from suspend,
starting poll or interrupt triggers. In these 3 situations, the
jack_dirty will be set to 1 first, then the hda_jack.c reads the
pin_sense from register, after reading the register, the jack_dirty
will be set to 0. But hdmi_repoll_work() is enabled in these 3
situations, It will read the pin_sense a couple of times subsequently,
since the jack_dirty is 0 now, It does not read the register anymore,
instead it uses the shadow pin_sense which is read at the first time.
It is meaningless to check the shadow pin_sense a couple of times,
we need to read the register to check the real plugging state, so
we set the jack_dirty to 1 in the hdmi_repoll_work().
In parse_audio_selector_unit(), the string array 'namelist' is allocated
through kmalloc_array(), and each string pointer in this array, i.e.,
'namelist[]', is allocated through kmalloc() in the following for loop.
Then, a control instance 'kctl' is created by invoking snd_ctl_new1(). If
an error occurs during the creation process, the string array 'namelist',
including all string pointers in the array 'namelist[]', should be freed,
before the error code ENOMEM is returned. However, the current code does
not free 'namelist[]', resulting in memory leaks.
To fix the above issue, free all string pointers 'namelist[]' in a loop.
The ->digest() method of crct10dif-pclmul reads the current CRC value
from the shash_desc context. But this value is uninitialized, causing
crypto_shash_digest() to compute the wrong result. Fix it.
Probably this wasn't noticed before because lib/crc-t10dif.c only uses
crypto_shash_update(), not crypto_shash_digest(). Likewise,
crypto_shash_digest() is not yet tested by the crypto self-tests because
those only test the ahash API which only uses shash init/update/final.
Fixes: 0b95a7f85718 ("crypto: crct10dif - Glue code to cast accelerated CRCT10DIF assembly as a crypto transform") Cc: <stable@vger.kernel.org> # v3.11+ Cc: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ->digest() method of crct10dif-generic reads the current CRC value
from the shash_desc context. But this value is uninitialized, causing
crypto_shash_digest() to compute the wrong result. Fix it.
Probably this wasn't noticed before because lib/crc-t10dif.c only uses
crypto_shash_update(), not crypto_shash_digest(). Likewise,
crypto_shash_digest() is not yet tested by the crypto self-tests because
those only test the ahash API which only uses shash init/update/final.
This bug was detected by my patches that improve testmgr to fuzz
algorithms against their generic implementation.
Fixes: 2d31e518a428 ("crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework") Cc: <stable@vger.kernel.org> # v3.11+ Cc: Tim Chen <tim.c.chen@linux.intel.com> Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original assembly imported from OpenSSL has two copy-paste
errors in handling CTR mode. When dealing with a 2 or 3 block tail,
the code branches to the CBC decryption exit path, rather than to
the CTR exit path.
This leads to corruption of the IV, which leads to subsequent blocks
being corrupted.
This can be detected with libkcapi test suite, which is available at
https://github.com/smuellerDD/libkcapi
Reported-by: Ondrej Mosnáček <omosnacek@gmail.com> Fixes: 5c380d623ed3 ("crypto: vmx - Add support for VMS instructions by ASM") Cc: stable@vger.kernel.org Signed-off-by: Daniel Axtens <dja@axtens.net> Tested-by: Michael Ellerman <mpe@ellerman.id.au> Tested-by: Ondrej Mosnacek <omosnacek@gmail.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the rfc7539 template is instantiated with specific implementations,
e.g. "rfc7539(chacha20-generic,poly1305-generic)" rather than
"rfc7539(chacha20,poly1305)", then the implementation names end up
included in the instance's cra_name. This is incorrect because it then
prevents all users from allocating "rfc7539(chacha20,poly1305)", if the
highest priority implementations of chacha20 and poly1305 were selected.
Also, the self-tests aren't run on an instance allocated in this way.
Fix it by setting the instance's cra_name from the underlying
algorithms' actual cra_names, rather than from the requested names.
This matches what other templates do.
Fixes: 71ebc4d1b27d ("crypto: chacha20poly1305 - Add a ChaCha20-Poly1305 AEAD construction, RFC7539") Cc: <stable@vger.kernel.org> # v4.2+ Cc: Martin Willi <martin@strongswan.org> Signed-off-by: Eric Biggers <ebiggers@google.com> Reviewed-by: Martin Willi <martin@strongswan.org> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2c7577a75837 ("sched/x86_64: Don't save flags on context switch")
Specifically because SMAP uses FLAGS.AC which invalidates the claim
that the kernel has clean flags.
In particular; while preemption from interrupt return is fine (the
IRET frame on the exception stack contains FLAGS) it breaks any code
that does synchonous scheduling, including preempt_enable().
This has become a significant issue ever since commit:
5b24a7a2aa20 ("Add 'unsafe' user access functions for batched accesses")
provided for means of having 'normal' C code between STAC / CLAC,
exposing the FLAGS.AC state. So far this hasn't led to trouble,
however fix it before it comes apart.
Reported-by: Julien Thierry <julien.thierry@arm.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Andy Lutomirski <luto@amacapital.net> Cc: Borislav Petkov <bp@alien8.de> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@kernel.org Fixes: 5b24a7a2aa20 ("Add 'unsafe' user access functions for batched accesses") Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, compat tasks running on arm64 can allocate memory up to
TASK_SIZE_32 (UL(0x100000000)).
This means that mmap() allocations, if we treat them as returning an
array, are not compliant with the sections 6.5.8 of the C standard
(C99) which states that: "If the expression P points to an element of
an array object and the expression Q points to the last element of the
same array object, the pointer expression Q+1 compares greater than P".
Currently there is no check on platform_get_irq() return value
in case it fails, hence never actually reporting any errors and
causing unexpected behavior when using such value as argument
for function regmap_irq_get_virq().
Fix this by adding a proper check, a message reporting any errors
and returning *pirq*
Addresses-Coverity-ID: 1443940 ("Improper use of negative value") Fixes: 843735b788a4 ("power: axp288_charger: axp288 charger driver") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with warnings like:
arch/arm/mach-exynos/firmware.c:201:2-8: ERROR: missing of_node_put;
acquired a node pointer with refcount incremented on line 193,
but without a corresponding object release within this function.
Cc: stable@vger.kernel.org Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a function falls through to the next function due to a compiler
bug, objtool prints some obscure warnings. For example:
drivers/regulator/core.o: warning: objtool: regulator_count_voltages()+0x95: return with modified stack frame
drivers/regulator/core.o: warning: objtool: regulator_count_voltages()+0x0: stack state mismatch: cfa1=7+32 cfa2=7+8
Instead it should be printing:
drivers/regulator/core.o: warning: objtool: regulator_supply_is_couple() falls through to next function regulator_count_voltages()
This used to work, but was broken by the following commit:
13810435b9a7 ("objtool: Support GCC 8's cold subfunctions")
The padding nops at the end of a function aren't actually part of the
function, as defined by the symbol table. So the 'func' variable in
validate_branch() is getting cleared to NULL when a padding nop is
encountered, breaking the fallthrough detection.
If the current instruction doesn't have a function associated with it,
just consider it to be part of the previously detected function by not
overwriting the previous value of 'func'.
On x86_64, all returns to usermode go through
prepare_exit_to_usermode(), with the sole exception of do_nmi().
This even includes machine checks -- this was added several years
ago to support MCE recovery. Update the documentation.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@suse.de> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jon Masters <jcm@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: 04dcbdb80578 ("x86/speculation/mds: Clear CPU buffers on exit to user") Link: http://lkml.kernel.org/r/999fa9e126ba6a48e9d214d2f18dbde5c62ac55c.1557865329.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The double fault ESPFIX path doesn't return to user mode at all --
it returns back to the kernel by simulating a #GP fault.
prepare_exit_to_usermode() will run on the way out of
general_protection before running user code.
Signed-off-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@suse.de> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Jon Masters <jcm@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Fixes: 04dcbdb80578 ("x86/speculation/mds: Clear CPU buffers on exit to user") Link: http://lkml.kernel.org/r/ac97612445c0a44ee10374f6ea79c222fe22a5c4.1557865329.git.luto@kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a device is created in new_pcichild_device(), hpdev->refs is set
to 2 (i.e. the initial value of 1 plus the get_pcichild()).
When we hot remove the device from the host, in a Linux VM we first call
hv_pci_eject_device(), which increases hpdev->refs by get_pcichild() and
then schedules a work of hv_eject_device_work(), so hpdev->refs becomes
3 (let's ignore the paired get/put_pcichild() in other places). But in
hv_eject_device_work(), currently we only call put_pcichild() twice,
meaning the 'hpdev' struct can't be freed in put_pcichild().
Add one put_pcichild() to fix the memory leak.
The device can also be removed when we run "rmmod pci-hyperv". On this
path (hv_pci_remove() -> hv_pci_bus_exit() -> hv_pci_devices_present()),
hpdev->refs is 2, and we do correctly call put_pcichild() twice in
pci_devices_present_work().
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs") Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: commit log rework] Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Reviewed-by: Stephen Hemminger <stephen@networkplumber.org> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Cc: stable@vger.kernel.org Signed-off-by: Sasha Levin <sashal@kernel.org>
During my rwsem testing, it was found that after a down_read(), the
reader count may occasionally become 0 or even negative. Consequently,
a writer may steal the lock at that time and execute with the reader
in parallel thus breaking the mutual exclusion guarantee of the write
lock. In other words, both readers and writer can become rwsem owners
simultaneously.
The current reader wakeup code does it in one pass to clear waiter->task
and put them into wake_q before fully incrementing the reader count.
Once waiter->task is cleared, the corresponding reader may see it,
finish the critical section and do unlock to decrement the count before
the count is incremented. This is not a problem if there is only one
reader to wake up as the count has been pre-incremented by 1. It is
a problem if there are more than one readers to be woken up and writer
can steal the lock.
The wakeup was actually done in 2 passes before the following v4.9 commit:
70800c3c0cc5 ("locking/rwsem: Scan the wait_list for readers only once")
To fix this problem, the wakeup is now done in two passes
again. In the first pass, we collect the readers and count them.
The reader count is then fully incremented. In the second pass, the
waiter->task is then cleared and they are put into wake_q to be woken
up later.
Signed-off-by: Waiman Long <longman@redhat.com> Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tim Chen <tim.c.chen@linux.intel.com> Cc: Will Deacon <will.deacon@arm.com> Cc: huang ying <huang.ying.caritas@gmail.com> Fixes: 70800c3c0cc5 ("locking/rwsem: Scan the wait_list for readers only once") Link: http://lkml.kernel.org/r/20190428212557.13482-2-longman@redhat.com Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
First example of a layer splitting the list (rather than merely taking
individual packets off it).
Involves new list.h function, list_cut_before(), like list_cut_position()
but cuts on the other side of the given entry.
Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[sl: cut out non list.h bits, we only want list_cut_before] Signed-off-by: Sasha Levin <sashal@kernel.org>
Set RI in the default kernel's MSR so that the architected way of
detecting unrecoverable machine check interrupts has a chance to work.
This is inline with the MSR setup of the rest of booke powerpc
architectures configured here.
Commit 51c3c62b58b3 ("powerpc: Avoid code patching freed init
sections") accesses 'init_mem_is_free' flag too early, before the
kernel is relocated. This provokes early boot failure (before the
console is active).
As it is not necessary to do this verification that early, this
patch moves the test into patch_instruction() instead of
__patch_instruction().
This modification also has the advantage of avoiding unnecessary
remappings.
The "param.count" value is a u64 thatcomes from the user. The code
later in the function assumes that param.count is at least one and if
it's not then it leads to an Oops when we dereference the ZERO_SIZE_PTR.
Also the addition can have an integer overflow which would lead us to
allocate a smaller "pages" array than required. I can't immediately
tell what the possible run times implications are, but it's safest to
prevent the overflow.
Link: http://lkml.kernel.org/r/20181218082129.GE32567@kadam Fixes: 6db7199407ca ("drivers/virt: introduce Freescale hypervisor management driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Andrew Morton <akpm@linux-foundation.org> Cc: Timur Tabi <timur@freescale.com> Cc: Mihai Caraman <mihai.caraman@freescale.com> Cc: Kumar Gala <galak@kernel.crashing.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's currently a problem with toggling arp_validate on and off with an
active-backup bond. At the moment, you can start up a bond, like so:
modprobe bonding mode=1 arp_interval=100 arp_validate=0 arp_ip_targets=192.168.1.1
ip link set bond0 down
echo "ens4f0" > /sys/class/net/bond0/bonding/slaves
echo "ens4f1" > /sys/class/net/bond0/bonding/slaves
ip link set bond0 up
ip addr add 192.168.1.2/24 dev bond0
Pings to 192.168.1.1 work just fine. Now turn on arp_validate:
Pings to 192.168.1.1 continue to work just fine. Now when you go to turn
arp_validate off again, the link falls flat on it's face:
echo 0 > /sys/class/net/bond0/bonding/arp_validate
dmesg
...
[133191.911987] bond0: Setting arp_validate to none (0)
[133194.257793] bond0: bond_should_notify_peers: slave ens4f0
[133194.258031] bond0: link status definitely down for interface ens4f0, disabling it
[133194.259000] bond0: making interface ens4f1 the new active one
[133197.330130] bond0: link status definitely down for interface ens4f1, disabling it
[133197.331191] bond0: now running without any active interface!
The problem lies in bond_options.c, where passing in arp_validate=0
results in bond->recv_probe getting set to NULL. This flies directly in
the face of commit 3fe68df97c7f, which says we need to set recv_probe =
bond_arp_recv, even if we're not using arp_validate. Said commit fixed
this in bond_option_arp_interval_set, but missed that we can get to that
same state in bond_option_arp_validate_set as well.
One solution would be to universally set recv_probe = bond_arp_recv here
as well, but I don't think bond_option_arp_validate_set has any business
touching recv_probe at all, and that should be left to the arp_interval
code, so we can just make things much tidier here.
Fixes: 3fe68df97c7f ("bonding: always set recv_probe to bond_arp_rcv in arp monitor") CC: Jay Vosburgh <j.vosburgh@gmail.com> CC: Veaceslav Falico <vfalico@gmail.com> CC: Andy Gospodarek <andy@greyhouse.net> CC: "David S. Miller" <davem@davemloft.net> CC: netdev@vger.kernel.org Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
inet_iif should be used for the raw socket lookup. inet_iif considers
rt_iif which handles the case of local traffic.
As it stands, ping to a local address with the '-I <dev>' option fails
ever since ping was changed to use SO_BINDTODEVICE instead of
cmsg + IP_PKTINFO.
IPv6 works fine.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VRF netdev mtu isn't typically set and have an mtu of 65536. When the
link of a tunnel is set, the tunnel mtu is changed from 1480 to the link
mtu minus tunnel header. In the case of VRF netdev is the link, then the
tunnel mtu becomes 65516. So, fix it by not setting the tunnel mtu in
this case.
Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With NET_ADMIN enabled in container, a normal user could be mapped to
root and is able to change the real device's rx filter via ioctl on
vlan, which would affect the other ptp process on host. Fix it by
disabling SIOCSHWTSTAMP in container.
Fixes: a6111d3c93d0 ("vlan: Pass SIOC[SG]HWTSTAMP ioctls to real device") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When modprobe af_packet, register_pernet_subsys
fails and does a cleanup, ops->list is set to LIST_POISON1,
but the module init is considered to success, then while rmmod it,
BUG() is triggered in __list_del_entry_valid which is called from
unregister_pernet_subsys. This patch fix error handing path in
packet_init to avoid possilbe issue if some error occur.
Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When changing the number of buffers in the RX ring while the interface
is running, the following Oops is encountered due to the new number
of buffers being taken into account immediately while their allocation
is done when opening the device only.
With commit 153380ec4b9 ("fib_rules: Added NLM_F_EXCL support to
fib_nl_newrule") we now able to check if a rule already exists. But this
only works with iproute2. For other tools like libnl, NetworkManager,
it still could add duplicate rules with only NLM_F_CREATE flag, like
[localhost ~ ]# ip rule
0: from all lookup local
32766: from all lookup main
32767: from all lookup default
100000: from 192.168.7.5 lookup 5
100000: from 192.168.7.5 lookup 5
As it doesn't make sense to create two duplicate rules, let's just return
0 if the rule exists.
Fixes: 153380ec4b9 ("fib_rules: Added NLM_F_EXCL support to fib_nl_newrule") Reported-by: Thomas Haller <thaller@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently error return from kobject_init_and_add() is not followed by a
call to kobject_put(). This means there is a memory leak. We currently
set p to NULL so that kfree() may be called on it as a noop, the code is
arguably clearer if we move the kfree() up closer to where it is
called (instead of after goto jump).
Remove a goto label 'err1' and jump to call to kobject_put() in error
return from kobject_init_and_add() fixing the memory leak. Re-name goto
label 'put_back' to 'err1' now that we don't use err1, following current
nomenclature (err1, err2 ...). Move call to kfree out of the error
code at bottom of function up to closer to where memory was allocated.
Add comment to clarify call to kfree().
Signed-off-by: Tobin C. Harding <tobin@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current powerpc security.c file is defining functions, as
cpu_show_meltdown(), cpu_show_spectre_v{1,2} and others, that are being
declared at linux/cpu.h header without including the header file that
contains these declarations.
This is being reported by sparse, which thinks that these functions are
static, due to the lack of declaration:
arch/powerpc/kernel/security.c:105:9: warning: symbol 'cpu_show_meltdown' was not declared. Should it be static?
arch/powerpc/kernel/security.c:139:9: warning: symbol 'cpu_show_spectre_v1' was not declared. Should it be static?
arch/powerpc/kernel/security.c:161:9: warning: symbol 'cpu_show_spectre_v2' was not declared. Should it be static?
arch/powerpc/kernel/security.c:209:6: warning: symbol 'stf_barrier' was not declared. Should it be static?
arch/powerpc/kernel/security.c:289:9: warning: symbol 'cpu_show_spec_store_bypass' was not declared. Should it be static?
This patch simply includes the proper header (linux/cpu.h) to match
function definition and declaration.
Signed-off-by: Breno Leitao <leitao@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Cc: Joel Stanley <joel@jms.id.au> Cc: Nathan Chancellor <natechancellor@gmail.com> Cc: Major Hayden <major@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
379d98ddf413 ("x86: vdso: Use $LD instead of $CC to link")
accidentally broke unwinding from userspace, because ld would strip the
.eh_frame sections when linking.
Originally, the compiler would implicitly add --eh-frame-hdr when
invoking the linker, but when this Makefile was converted from invoking
ld via the compiler, to invoking it directly (like vmlinux does),
the flag was missed. (The EH_FRAME section is important for the VDSO
shared libraries, but not for vmlinux.)
Fix the problem by explicitly specifying --eh-frame-hdr, which restores
parity with the old method.
GNU linker's -z common-page-size's default value is based on the target
architecture. arch/x86/entry/vdso/Makefile sets it to the architecture
default, which is implicit and redundant. Drop it.
Fixes: 2aae950b21e4 ("x86_64: Add vDSO for x86-64 with gettimeofday/clock_gettime/getcpu") Reported-by: Dmitry Golovin <dima@golovin.in> Reported-by: Bill Wendling <morbo@google.com> Suggested-by: Dmitry Golovin <dima@golovin.in> Suggested-by: Rui Ueyama <ruiu@google.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Borislav Petkov <bp@suse.de> Acked-by: Andy Lutomirski <luto@kernel.org> Cc: Andi Kleen <andi@firstfloor.org> Cc: Fangrui Song <maskray@google.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20181206191231.192355-1-ndesaulniers@google.com Link: https://bugs.llvm.org/show_bug.cgi?id=38774 Link: https://github.com/ClangBuiltLinux/linux/issues/31 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The vdso{32,64}.so can fail to link with CC=clang when clang tries to find
a suitable GCC toolchain to link these libraries with.
/usr/bin/ld: arch/x86/entry/vdso/vclock_gettime.o:
access beyond end of merged section (782)
This happens because the host environment leaked into the cross compiler
environment due to the way clang searches for suitable GCC toolchains.
Clang is a retargetable compiler, and each invocation of it must provide
--target=<something> --gcc-toolchain=<something> to allow it to find the
correct binutils for cross compilation. These flags had been added to
KBUILD_CFLAGS, but the vdso code uses CC and not KBUILD_CFLAGS (for various
reasons) which breaks clang's ability to find the correct linker when cross
compiling.
Most of the time this goes unnoticed because the host linker is new enough
to work anyway, or is incompatible and skipped, but this cannot be reliably
assumed.
This change alters the vdso makefile to just use LD directly, which
bypasses clang and thus the searching problem. The makefile will just use
${CROSS_COMPILE}ld instead, which is always what we want. This matches the
method used to link vmlinux.
This drops references to DISABLE_LTO; this option doesn't seem to be set
anywhere, and not knowing what its possible values are, it's not clear how
to convert it from CC to LD flag.
Changing state from check_state_check_result to
check_state_compute_result not only is unsafe but also doesn't
appear to serve a valid purpose. A raid6 check should only be
pushing out extra writes if doing repair and a mis-match occurs.
The stripe dev management will already try and do repair writes
for failing sectors.
This patch makes the raid6 check_state_check_result handling
work more like raid5's. If somehow too many failures for a
check, just quit the check operation for the stripe. When any
checks pass, don't try and use check_state_compute_result for
a purpose it isn't needed for and is unsafe for. Just mark the
stripe as in sync for passing its parity checks and let the
stripe dev read/write code and the bad blocks list do their
job handling I/O errors.
Repro steps from Xiao:
These are the steps to reproduce this problem:
1. redefined OPT_MEDIUM_ERR_ADDR to 12000 in scsi_debug.c
2. insmod scsi_debug.ko dev_size_mb=11000 max_luns=1 num_tgts=1
3. mdadm --create /dev/md127 --level=6 --raid-devices=5 /dev/sde1 /dev/sde2 /dev/sde3 /dev/sde5 /dev/sde6
sde is the disk created by scsi_debug
4. echo "2" >/sys/module/scsi_debug/parameters/opts
5. raid-check
Add missing break statement in order to prevent the code from falling
through to case 0x1025, and erroneously setting rtlhal->oem_id to
RT_CID_819X_ACER when rtlefuse->eeprom_svid is equal to 0x10EC and
none of the cases in switch (rtlefuse->eeprom_smid) match.
This bug was found thanks to the ongoing efforts to enable
-Wimplicit-fallthrough.
Fixes: 238ad2ddf34b ("rtlwifi: rtl8723ae: Clean up the hardware info routine") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers can implement 'struct snd_pcm_ops.ioctl' to handle some requests
from ALSA PCM core. These requests are internal purpose in kernel land.
Usually common set of operations are used for it.
SNDRV_PCM_IOCTL1_INFO is one of the requests. According to code comment,
it has been obsoleted in the old days.
We can see old releases in ftp.alsa-project.org. The command was firstly
introduced in v0.5.0 release as SND_PCM_IOCTL1_INFO, to allow drivers to
fill data of 'struct snd_pcm_channel_info' type. In v0.9.0 release,
this was obsoleted by the other commands for ioctl(2) such as
SNDRV_PCM_IOCTL_CHANNEL_INFO.
This commit removes the long-abandoned command, bye.
The RMI4 function structure has been released in rmi_register_function
if error occurs. However, it will be released again in the function
rmi_create_function, which may result in a double-free bug.
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
After this patch:
modinfo drivers/nfc/st95hf/st95hf.ko | grep alias
alias: spi:st95hf
alias: of:N*T*Cst,st95hfC*
alias: of:N*T*Cst,st95hf
Reported-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Daniel Gomez <dagmcr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add missing <of_device_id> table for SPI driver relying on SPI
device match since compatible is in a DT binding or in a DTS.
Before this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
After this patch:
modinfo drivers/net/phy/spi_ks8995.ko | grep alias
alias: spi:ksz8795
alias: spi:ksz8864
alias: spi:ks8995
alias: of:N*T*Cmicrel,ksz8795C*
alias: of:N*T*Cmicrel,ksz8795
alias: of:N*T*Cmicrel,ksz8864C*
alias: of:N*T*Cmicrel,ksz8864
alias: of:N*T*Cmicrel,ks8995C*
alias: of:N*T*Cmicrel,ks8995
Reported-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Daniel Gomez <dagmcr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Initialize the flow input colorspaces to unknown and reset to that value
when the channel gets disabled. This avoids the state getting mixed up
with a previous mode.
Also keep the CSC settings for the background flow intact when disabling
the foreground flow.
Root-caused-by: Jonathan Marek <jonathan@marek.ca> Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The run_netsocktests will be marked as passed regardless the actual test
result from the ./socket:
selftests: net: run_netsocktests
========================================
--------------------
running socket test
--------------------
[FAIL]
ok 1..6 selftests: net: run_netsocktests [PASS]
This is because the test script itself has been successfully executed.
Fix this by exit 1 when the test failed.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang points out that the return code from this function is
undefined for one of the error paths:
../drivers/s390/net/ctcm_main.c:1595:7: warning: variable 'result' is used uninitialized whenever 'if' condition is true
[-Wsometimes-uninitialized]
if (priv->channel[direction] == NULL) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/s390/net/ctcm_main.c:1638:9: note: uninitialized use occurs here
return result;
^~~~~~
../drivers/s390/net/ctcm_main.c:1595:3: note: remove the 'if' if its condition is always false
if (priv->channel[direction] == NULL) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/s390/net/ctcm_main.c:1539:12: note: initialize the variable 'result' to silence this warning
int result;
^
Make it return -ENODEV here, as in the related failure cases.
gcc has a known bug in underreporting some of these warnings
when it has already eliminated the assignment of the return code
based on some earlier optimization step.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently it's not possible to use perf on ath79 due to genirq flags
mismatch happening on static virtual IRQ 13 which is used for
performance counters hardware IRQ 5.
$ perf top
genirq: Flags mismatch irq 13. 00014c80 (mips_perf_pmu) vs. 00000080 (ehci_hcd:usb1)
This problem is happening, because currently statically assigned virtual
IRQ 13 for performance counters is not claimed during the initialization
of MIPS PMU during the bootup, so the IRQ subsystem doesn't know, that
this interrupt isn't available for further use.
So this patch fixes the issue by simply booking hardware IRQ 5 for MIPS PMU.
Tested-by: Kevin 'ldir' Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Signed-off-by: Petr Štetiar <ynezz@true.cz> Acked-by: John Crispin <john@phrozen.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Paul Burton <paul.burton@mips.com> Cc: linux-mips@vger.kernel.org Cc: Ralf Baechle <ralf@linux-mips.org> Cc: James Hogan <jhogan@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can receive ICMP errors from client or from
tunneling real server. While the former can be
scheduled to real server, the latter should
not be scheduled, they are decapsulated only when
existing connection is found.
Fixes: 6044eeffafbe ("ipvs: attempt to schedule icmp packets") Signed-off-by: Julian Anastasov <ja@ssi.bg> Signed-off-by: Simon Horman <horms@verge.net.au> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an icmp error such as pkttoobig is received, conntrack checks
if the "inner" header (header of packet that did not fit link mtu)
is matches an existing connection, and, if so, sets that packet as
being related to the conntrack entry it found.
It was recently reported that this "related" setting also works
if the inner header is from another, different connection (i.e.,
artificial/forged icmp error).
Add a test, followup patch will add additional "inner dst matches
outer dst in reverse direction" check before setting related state.
When a module option, or core kernel argument, toggles a static-key it
requires jump labels to be initialized early. While x86, PowerPC, and
ARM64 arrange for jump_label_init() to be called before parse_args(),
ARM does not.
Kernel command line: rdinit=/sbin/init page_alloc.shuffle=1 panic=-1 console=ttyAMA0,115200 page_alloc.shuffle=1
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at ./include/linux/jump_label.h:303
page_alloc_shuffle+0x12c/0x1ac
static_key_enable(): static key 'page_alloc_shuffle_key+0x0/0x4' used
before call to jump_label_init()
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 5.1.0-rc4-next-20190410-00003-g3367c36ce744 #1
Hardware name: ARM Integrator/CP (Device Tree)
[<c0011c68>] (unwind_backtrace) from [<c000ec48>] (show_stack+0x10/0x18)
[<c000ec48>] (show_stack) from [<c07e9710>] (dump_stack+0x18/0x24)
[<c07e9710>] (dump_stack) from [<c001bb1c>] (__warn+0xe0/0x108)
[<c001bb1c>] (__warn) from [<c001bb88>] (warn_slowpath_fmt+0x44/0x6c)
[<c001bb88>] (warn_slowpath_fmt) from [<c0b0c4a8>]
(page_alloc_shuffle+0x12c/0x1ac)
[<c0b0c4a8>] (page_alloc_shuffle) from [<c0b0c550>] (shuffle_store+0x28/0x48)
[<c0b0c550>] (shuffle_store) from [<c003e6a0>] (parse_args+0x1f4/0x350)
[<c003e6a0>] (parse_args) from [<c0ac3c00>] (start_kernel+0x1c0/0x488)
Move the fallback call to jump_label_init() to occur before
parse_args().
The redundant calls to jump_label_init() in other archs are left intact
in case they have static key toggling use cases that are even earlier
than option parsing.
Link: http://lkml.kernel.org/r/155544804466.1032396.13418949511615676665.stgit@dwillia2-desk3.amr.corp.intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com> Reported-by: Guenter Roeck <groeck@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Mike Rapoport <rppt@linux.ibm.com> Cc: Russell King <rmk@armlinux.org.uk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There was a missing comparison with 0 when checking if type is "s64" or
"u64". Therefore, the body of the if-statement was entered if "type" was
"u64" or not "s64", which made the first strcmp() redundant since if
type is "u64", it's not "s64".
If type is "s64", the body of the if-statement is not entered but since
the remainder of the function consists of if-statements which will not
be entered if type is "s64", we will just return "val", which is
correct, albeit at the cost of a few more calls to strcmp(), i.e., it
will behave just as if the if-statement was entered.
If type is neither "s64" or "u64", the body of the if-statement will be
entered incorrectly and "val" returned. This means that any type that is
checked after "s64" and "u64" is handled the same way as "s64" and
"u64", i.e., the limiting of "val" to fit in for example "s8" is never
reached.
This was introduced in the kernel tree when the sources were copied from
trace-cmd in commit f7d82350e597 ("tools/events: Add files to create
libtraceevent.a"), and in the trace-cmd repo in 1cdbae6035cei
("Implement typecasting in parser") when the function was introduced,
i.e., it has always behaved the wrong way.
In __apic_accept_irq() interface trig_mode is int and actually on some code
paths it is set above u8:
kvm_apic_set_irq() extracts it from 'struct kvm_lapic_irq' where trig_mode
is u16. This is done on purpose as e.g. kvm_set_msi_irq() sets it to
(1 << 15) & e->msi.data
kvm_apic_local_deliver sets it to reg & (1 << 15).
Fix the immediate issue by making 'tm' into u16. We may also want to adjust
__apic_accept_irq() interface and use proper sizes for vector, level,
trig_mode but this is not urgent.
Upon reboot, the Acer TravelMate X514-51T laptop appears to complete the
shutdown process, but then it hangs in BIOS POST with a black screen.
The problem is intermittent - at some points it has appeared related to
Secure Boot settings or different kernel builds, but ultimately we have
not been able to identify the exact conditions that trigger the issue to
come and go.
Besides, the EFI mode cannot be disabled in the BIOS of this model.
However, after extensive testing, we observe that using the EFI reboot
method reliably avoids the issue in all cases.
So add a boot time quirk to use EFI reboot on such systems.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=203119 Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Daniel Drake <drake@endlessm.com> Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Cc: linux@endlessm.com Link: http://lkml.kernel.org/r/20190412080152.3718-1-jian-hong@endlessm.com
[ Fix !CONFIG_EFI build failure, clarify the code and the changelog a bit. ] Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
KMSAN will complain if valid address length passed to bind() is shorter
than sizeof("struct sockaddr_mISDN"->family) bytes.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The spinlock in the raw3270_view structure is used by con3270, tty3270
and fs3270 in different ways. For con3270 the lock can be acquired in
irq context, for tty3270 and fs3270 the highest context is bh.
Lockdep sees the view->lock as a single class and if the 3270 driver
is used for the console the following message is generated:
The DASD driver incorrectly limits the maximum number of blocks of ECKD
DASD volumes to 32 bit numbers. Volumes with a capacity greater than
2^32-1 blocks are incorrectly recognized as smaller volumes.
This results in the following volume capacity limits depending on the
formatted block size:
According to HUT 1.12 usage 0xb5 from the generic desktop page is reserved
for switching between external and internal display, so let's add the
mapping.
According to HUTRR77 usage 0x29f from the consumer page is reserved for
the Desktop application to present all running user’s application windows.
Linux defines KEY_SCALE to request Compiz Scale (Expose) mode, so let's
add the mapping.
When cancel_delayed_work() returns, the delayed work may still
be running. This means that the core could potentially free
the private structure (struct xadc) while the delayed work
is still using it. This is a potential use-after-free.
Fix by calling cancel_delayed_work_sync(), which waits for
any residual work to finish before returning.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix two long-standing bugs which could potentially lead to memory
corruption or leave the port throttled until it is reopened (on weakly
ordered systems), respectively, when read-URB completion races with
unthrottle().
First, the URB must not be marked as free before processing is complete
to prevent it from being submitted by unthrottle() on another CPU.
CPU 1 CPU 2
================ ================
complete() unthrottle()
process_urb();
smp_mb__before_atomic();
set_bit(i, free); if (test_and_clear_bit(i, free))
submit_urb();
Second, the URB must be marked as free before checking the throttled
flag to prevent unthrottle() on another CPU from failing to observe that
the URB needs to be submitted if complete() sees that the throttled flag
is set.
CPU 1 CPU 2
================ ================
complete() unthrottle()
set_bit(i, free); throttled = 0;
smp_mb__after_atomic(); smp_mb();
if (throttled) if (test_and_clear_bit(i, free))
return; submit_urb();
Note that test_and_clear_bit() only implies barriers when the test is
successful. To handle the case where the URB is still in use an explicit
barrier needs to be added to unthrottle() for the second race condition.
Fixes: d83b405383c9 ("USB: serial: add support for multiple read urbs") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It seems that the default case should return AE_CTRL_TERMINATE, instead
of falling through to case ACPI_RESOURCE_TYPE_END_TAG and returning AE_OK;
otherwise the line of code at the end of the function is unreachable and
makes no sense:
return AE_CTRL_TERMINATE;
This fix is based on the following thread of discussion:
https://lore.kernel.org/patchwork/patch/959782/
Fixes: 33a04454527e ("sony-laptop: Add SNY6001 device handling (sonypi reimplementation)") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when all map elements are pre-allocated one cpu can delete and reuse htab_elem
while another cpu is still walking the hlist. In such case the lookup may
miss the element. Convert hlist to hlist_nulls to avoid such scenario.
When bucket lock is taken there is no need to take such precautions,
so only convert map_lookup and map_get_next to nulls.
The race window is extremely small and only reproducible with explicit
udelay() inside lookup_nulls_elem_raw()
Similar to hlist add hlist_nulls_for_each_entry_safe() and
hlist_nulls_entry_safe() helpers.
Fixes: 6c9059817432 ("bpf: pre-allocate hash map elements") Reported-by: Jonathan Perry <jonperry@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chenbo Feng <fengc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
when htab_elem is removed from the bucket list the htab_elem.hash_node.next
field should not be overridden too early otherwise we have a tiny race window
between lookup and delete.
The bug was discovered by manual code analysis and reproducible
only with explicit udelay() in lookup_elem_raw().
Fixes: 6c9059817432 ("bpf: pre-allocate hash map elements") Reported-by: Jonathan Perry <jonperry@fb.com> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Chenbo Feng <fengc@google.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Even if this file was not in an uapi directory, it was exported because
it was listed in the Kbuild file.
Fixes: b72e7464e4cf ("x86/uapi: Do not export <asm/msr-index.h> as part of the user API headers") Suggested-by: Borislav Petkov <bp@alien8.de> Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by: Ingo Molnar <mingo@kernel.org> Acked-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log