After an event is sent, we try to copy it into the user buffer of the
first waiter in drm_read() and if the user buffer doesn't have enough
room we put it back onto the list. However, we didn't wake up any
subsequent waiter, so that event may sit on the list until either a new
vblank event is sent or a new waiter appears. Rare, but in the worst
case may lead to a stuck process.
Building with clang shows a variable that is only used by the
suspend/resume functions but defined outside of their #ifdef block:
sound/soc/ti/davinci-mcasp.c:48:12: error: variable 'context_regs' is not needed and will not be emitted
We commonly fix these by marking the PM functions as __maybe_unused,
but here that would grow the davinci_mcasp structure, so instead
add another #ifdef here.
Fixes: 1cc0c054f380 ("ASoC: davinci-mcasp: Convert the context save/restore to use array") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a bug for messages containing both zero length and
unidirectional xfers.
The function spi_map_msg will allocate dummy tx and/or rx buffers
for use with unidirectional transfers when the hardware can only do
a bidirectional transfer. That dummy buffer will be used in place
of a NULL buffer even when the xfer length is 0.
Then in the function __spi_map_msg, if he hardware can dma,
the zero length xfer will have spi_map_buf called on the dummy
buffer.
Eventually, __sg_alloc_table is called and returns -EINVAL
because nents == 0.
This fix prevents the error by not using the dummy buffer when
the xfer length is zero.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the sequencer is reset after each SPI message since commit 880c6d114fd79a69 ("spi: rspi: Add support for Quad and Dual SPI
Transfers on QSPI"), it was never reset for the first message, thus
relying on reset state or bootloader settings.
Fix this by initializing it explicitly during configuration.
Fixes: 0b2182ddac4b8837 ("spi: add support for Renesas RSPI") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
pch_alloc_dma_buf allocated tx, rx DMA buffers which can fail. Further,
these buffers are used without a check. The patch checks for these
failures and sends the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Two saa7146/hexium files contain a construct that causes a warning
when built with clang:
drivers/media/pci/saa7146/hexium_orion.c:210:12: error: stack frame size of 2272 bytes in function 'hexium_probe'
[-Werror,-Wframe-larger-than=]
static int hexium_probe(struct saa7146_dev *dev)
^
drivers/media/pci/saa7146/hexium_gemini.c:257:12: error: stack frame size of 2304 bytes in function 'hexium_attach'
[-Werror,-Wframe-larger-than=]
static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info)
^
This one happens regardless of KASAN, and the problem is that a
constructor to initialize a dynamically allocated structure leads
to a copy of that structure on the stack, whereas gcc initializes
it in place.
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.
Set the value to "Emulex Corporation" for consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
adma driver is using pm_clk_*() interface for managing clock resources.
With this it is observed that clocks remain ON always. This happens on
Tegra devices which use BPMP co-processor to manage clock resources,
where clocks are enabled during prepare phase. This is necessary because
clocks to BPMP are always blocking. When pm_clk_*() interface is used on
such Tegra devices, clock prepare count is not balanced till remove call
happens for the driver and hence clocks are seen ON always. Thus this
patch replaces pm_clk_*() with devm_clk_*() framework.
Clang -Wuninitialized notices that on is_qla40XX we never allocate any DMA
memory in get_fw_boot_info() but attempt to free it anyway:
drivers/scsi/qla4xxx/ql4_os.c:5915:7: error: variable 'buf_dma' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (!(val & 0x07)) {
^~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5985:47: note: uninitialized use occurs here
dma_free_coherent(&ha->pdev->dev, size, buf, buf_dma);
^~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5915:3: note: remove the 'if' if its condition is always true
if (!(val & 0x07)) {
^~~~~~~~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5885:20: note: initialize the variable 'buf_dma' to silence this warning
dma_addr_t buf_dma;
^
= 0
Skip the call to dma_free_coherent() here.
Fixes: 2a991c215978 ("[SCSI] qla4xxx: Boot from SAN support for open-iscsi") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If ohci-platform is runtime suspended, we can currently get an "imprecise
external abort" on reboot with ohci-platform loaded when PM runtime
is implemented for the SoC.
Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown.
Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the specified rcuperf.perf_type is not in the rcu_perf_init()
function's perf_ops[] array, rcuperf prints some console messages and
then invokes rcu_perf_cleanup() to set state so that a future torture
test can run. However, rcu_perf_cleanup() also attempts to end the
test that didn't actually start, and in doing so relies on the value
of cur_ops, a value that is not particularly relevant in this case.
This can result in confusing output or even follow-on failures due to
attempts to use facilities that have not been properly initialized.
This commit therefore sets the value of cur_ops to NULL in this case and
inserts a check near the beginning of rcu_perf_cleanup(), thus avoiding
relying on an irrelevant cur_ops value.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the specified rcutorture.torture_type is not in the rcu_torture_init()
function's torture_ops[] array, rcutorture prints some console messages
and then invokes rcu_torture_cleanup() to set state so that a future
torture test can run. However, rcu_torture_cleanup() also attempts to
end the test that didn't actually start, and in doing so relies on the
value of cur_ops, a value that is not particularly relevant in this case.
This can result in confusing output or even follow-on failures due to
attempts to use facilities that have not been properly initialized.
This commit therefore sets the value of cur_ops to NULL in this case
and inserts a check near the beginning of rcu_torture_cleanup(),
thus avoiding relying on an irrelevant cur_ops value.
Reported-by: kernel test robot <rong.a.chen@intel.com> Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There has been a lurking "TBD" in the machine check poll routine ever
since it was first split out from the machine check handler. The
potential issue is that the poll routine may have just begun a read from
the STATUS register in a machine check bank when the hardware logs an
error in that bank and signals a machine check.
That race used to be pretty small back when machine checks were
broadcast, but the addition of local machine check means that the poll
code could continue running and clear the error from the bank before the
local machine check handler on another CPU gets around to reading it.
Fix the code to be sure to only process errors that need to be processed
in the poll code, leaving other logged errors alone for the machine
check handler to find and process.
[ bp: Massage a bit and flip the "== 0" check to the usual !(..) test. ]
Fixes: b79109c3bbcf ("x86, mce: separate correct machine check poller and fatal exception handler") Fixes: ed7290d0ee8f ("x86, mce: implement new status bits") Reported-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Ashok Raj <ashok.raj@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Cc: Yazen Ghannam <Yazen.Ghannam@amd.com> Link: https://lkml.kernel.org/r/20190312170938.GA23035@agluck-desk Signed-off-by: Sasha Levin <sashal@kernel.org>
ipw->attr_memory and ipw->common_memory are assigned with the
return value of ioremap. ioremap may fail, but no checks
are enforced. The fix inserts the checks to avoid potential
NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For regular serial ports we do not initialize value of vtermno
variable. A garbage value is assigned for non console ports.
The value can be observed as a random integer with [1].
[1] vim /sys/kernel/debug/virtio-ports/vport*p*
This patch initialize the value of vtermno for console serial
ports to '1' and regular serial ports are initiaized to '0'.
Smatch marks skb->data as untrusted so it warns that "evt_hdr->dlen"
can copy up to 255 bytes and we only have room for two bytes. Even
if this comes from the firmware and we trust it, the new policy
generally is just to fix it as kernel hardenning.
I can't test this code so I tried to be very conservative. I considered
not allowing "evt_hdr->dlen == 1" because it doesn't initialize the
whole variable but in the end I decided to allow it and manually
initialized "asic_id" and "asic_ver" to zero.
Fixes: e8454ff7b9a4 ("[media] drivers:media:radio: wl128x: FM Driver Common sources") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The use of zero-sized array causes undefined behaviour when it is not
the last member in a structure. As it happens to be in this case.
Also, the current code makes use of a language extension to the C90
standard, but the preferred mechanism to declare variable-length
types such as this one is a flexible array member, introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last. Which is beneficial
to cultivate a high-quality code.
Fixes: e48f129c2f20 ("[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/fsl_utils.c:74:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 38, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Timur Tabi <timur@kernel.org> Cc: Nicolin Chen <nicoleotsuka@gmail.com> Cc: Xiubo Li <Xiubo.Lee@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/eukrea-tlv320.c:121:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function.
./sound/soc/fsl/eukrea-tlv320.c:127:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As seen on some USB wireless keyboards manufactured by Primax, the HID
parser was using some assumptions that are not always true. In this case
it's s the fact that, inside the scope of a main item, an Usage Page
will always precede an Usage.
The spec is not pretty clear as 6.2.2.7 states "Any usage that follows
is interpreted as a Usage ID and concatenated with the Usage Page".
While 6.2.2.8 states "When the parser encounters a main item it
concatenates the last declared Usage Page with a Usage to form a
complete usage value." Being somewhat contradictory it was decided to
match Window's implementation, which follows 6.2.2.8.
In summary, the patch moves the Usage Page concatenation from the local
item parsing function to the main item parsing function.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de> Reviewed-by: Terry Junge <terry.junge@poly.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Occasionally GCC is less agressive with inlining and the following is
observed:
arch/x86/kernel/signal.o: warning: objtool: restore_sigcontext()+0x3cc: call to force_valid_ss.isra.5() with UACCESS enabled
arch/x86/kernel/signal.o: warning: objtool: do_signal()+0x384: call to frame_uc_flags.isra.0() with UACCESS enabled
Cure this by moving this code out of the AC=1 region, since it really
isn't needed for the user access.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_get_next_child returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./arch/arm64/kernel/cpu_ops.c:102:1-7: ERROR: missing of_node_put;
acquired a node pointer with refcount incremented on line 69, but
without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will.deacon@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For regulators used by UFS, vcc, vccq and vccq2 will have voltage range
initialized by ufshcd_populate_vreg(), however other regulators may have
undefined voltage range if dt-bindings have no such definition.
In above undefined case, both "min_uV" and "max_uV" fields in ufs_vreg
struct will be zero values and these values will be configured on
regulators in different power modes.
Currently this may have no harm if both "min_uV" and "max_uV" always keep
"zero values" because regulator_set_voltage() will always bypass such
invalid values and return "good" results.
However improper values shall be fixed to avoid potential bugs. Simply
bypass voltage configuration if voltage range is not defined.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Acked-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if a regulator has "<name>-fixed-regulator" property in device
tree, it will skip current limit initialization. This lead to a zero
"max_uA" value in struct ufs_vreg.
However, "regulator_set_load" operation shall be required on regulators
which have valid current limits, otherwise a zero "max_uA" set by
"regulator_set_load" may cause unexpected behavior when this regulator is
enabled or set as high power mode.
Similarly, in device's icc_level configuration flow, the target icc_level
shall be updated if regulator also has valid current limit, otherwise a
wrong icc_level will be calculated by zero "max_uA" and thus causes
unexpected results after it is written to device.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Acked-by: Alim Akhtar <alim.akhtar@samsung.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a race which leads to an Oops with NULL pointer dereference. The
dereference is in brcmf_config_dongle() when cfg_to_ndev() attempts to get
net_device structure of interface with index 0 via if2bss mapping. This
shouldn't fail because of check for bus being ready in brcmf_netdev_open(),
but it's not synchronised with USB disconnect and there is a race: after
the check the bus can be marked down and the mapping for interface 0 may be
gone.
Solve this by modifying disconnect handling so that the removal of mapping
of ifidx to brcmf_if structure happens after netdev removal (which is
synchronous with brcmf_netdev_open() thanks to rtln being locked in
devinet_ioctl()). This assures brcmf_netdev_open() returns before the
mapping is removed during disconnect.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It was observed that rarely during USB disconnect happening shortly after
connect (before full initialization completes) usb_hub_wq would wait
forever for the dev_init_lock to be unlocked. dev_init_lock would remain
locked though because of infinite wait during usb_kill_urb:
[ 2730.656472] kworker/0:2 D 0 260 2 0x00000000
[ 2730.660700] Workqueue: events request_firmware_work_func
[ 2730.664807] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2730.670587] [<809dd164>] (schedule) from [<8069af44>] (usb_kill_urb+0xdc/0x114)
[ 2730.676815] [<8069af44>] (usb_kill_urb) from [<7f258b50>] (brcmf_usb_free_q+0x34/0xa8 [brcmfmac])
[ 2730.684833] [<7f258b50>] (brcmf_usb_free_q [brcmfmac]) from [<7f2517d4>] (brcmf_detach+0xa0/0xb8 [brcmfmac])
[ 2730.693557] [<7f2517d4>] (brcmf_detach [brcmfmac]) from [<7f251a34>] (brcmf_attach+0xac/0x3d8 [brcmfmac])
[ 2730.702094] [<7f251a34>] (brcmf_attach [brcmfmac]) from [<7f2587ac>] (brcmf_usb_probe_phase2+0x468/0x4a0 [brcmfmac])
[ 2730.711601] [<7f2587ac>] (brcmf_usb_probe_phase2 [brcmfmac]) from [<7f252888>] (brcmf_fw_request_done+0x194/0x220 [brcmfmac])
[ 2730.721795] [<7f252888>] (brcmf_fw_request_done [brcmfmac]) from [<805748e4>] (request_firmware_work_func+0x4c/0x88)
[ 2730.731125] [<805748e4>] (request_firmware_work_func) from [<80141474>] (process_one_work+0x228/0x808)
[ 2730.739223] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2730.746105] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2730.752227] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
[ 2733.099695] kworker/0:3 D 0 1065 2 0x00000000
[ 2733.103926] Workqueue: usb_hub_wq hub_event
[ 2733.106914] [<809dca20>] (__schedule) from [<809dd164>] (schedule+0x4c/0xac)
[ 2733.112693] [<809dd164>] (schedule) from [<809e2a8c>] (schedule_timeout+0x214/0x3e4)
[ 2733.119621] [<809e2a8c>] (schedule_timeout) from [<809dde2c>] (wait_for_common+0xc4/0x1c0)
[ 2733.126810] [<809dde2c>] (wait_for_common) from [<7f258d00>] (brcmf_usb_disconnect+0x1c/0x4c [brcmfmac])
[ 2733.135206] [<7f258d00>] (brcmf_usb_disconnect [brcmfmac]) from [<8069e0c8>] (usb_unbind_interface+0x5c/0x1e4)
[ 2733.143943] [<8069e0c8>] (usb_unbind_interface) from [<8056d3e8>] (device_release_driver_internal+0x164/0x1fc)
[ 2733.152769] [<8056d3e8>] (device_release_driver_internal) from [<8056c078>] (bus_remove_device+0xd0/0xfc)
[ 2733.161138] [<8056c078>] (bus_remove_device) from [<8056977c>] (device_del+0x11c/0x310)
[ 2733.167939] [<8056977c>] (device_del) from [<8069cba8>] (usb_disable_device+0xa0/0x1cc)
[ 2733.174743] [<8069cba8>] (usb_disable_device) from [<8069507c>] (usb_disconnect+0x74/0x1dc)
[ 2733.181823] [<8069507c>] (usb_disconnect) from [<80695e88>] (hub_event+0x478/0xf88)
[ 2733.188278] [<80695e88>] (hub_event) from [<80141474>] (process_one_work+0x228/0x808)
[ 2733.194905] [<80141474>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[ 2733.201724] [<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[ 2733.207913] [<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
It was traced down to a case where usb_kill_urb would be called on an URB
structure containing more or less random data, including large number in
its use_count. During the debugging it appeared that in brcmf_usb_free_q()
the traversal over URBs' lists is not synchronized with operations on those
lists in brcmf_usb_rx_complete() leading to handling
brcmf_usbdev_info structure (holding lists' head) as lists' element and in
result causing above problem.
Fix it by walking through all URBs during brcmf_cancel_all_urbs using the
arrays of requests instead of linked lists.
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Leaving dev_init_lock mutex locked in probe causes BUG and a WARNING when
kernel is compiled with CONFIG_PROVE_LOCKING. Convert mutex to completion
which silences those warnings and improves code readability.
Fix below errors when connecting the USB WiFi dongle:
brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43143 for chip BCM43143/2
BUG: workqueue leaked lock or atomic: kworker/0:2/0x00000000/434
last function: hub_event
1 lock held by kworker/0:2/434:
#0: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac]
CPU: 0 PID: 434 Comm: kworker/0:2 Not tainted 4.19.23-00084-g454a789-dirty #123
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Workqueue: usb_hub_wq hub_event
[<8011237c>] (unwind_backtrace) from [<8010d74c>] (show_stack+0x10/0x14)
[<8010d74c>] (show_stack) from [<809c4324>] (dump_stack+0xa8/0xd4)
[<809c4324>] (dump_stack) from [<8014195c>] (process_one_work+0x710/0x808)
[<8014195c>] (process_one_work) from [<80141a80>] (worker_thread+0x2c/0x564)
[<80141a80>] (worker_thread) from [<80147bcc>] (kthread+0x13c/0x16c)
[<80147bcc>] (kthread) from [<801010b4>] (ret_from_fork+0x14/0x20)
Exception stack(0xed1d9fb0 to 0xed1d9ff8)
9fa0: 00000000000000000000000000000000
9fc0: 0000000000000000000000000000000000000000000000000000000000000000
9fe0: 000000000000000000000000000000000000001300000000
======================================================
WARNING: possible circular locking dependency detected 4.19.23-00084-g454a789-dirty #123 Not tainted
------------------------------------------------------
kworker/0:2/434 is trying to acquire lock: e29cf799 ((wq_completion)"events"){+.+.}, at: process_one_work+0x174/0x808
but task is already holding lock: 18d5dcdf (&devinfo->dev_init_lock){+.+.}, at: brcmf_usb_probe+0x78/0x550 [brcmfmac]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
Signed-off-by: Piotr Figiel <p.figiel@camlintechnologies.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns about what is clearly a case of passing an uninitalized
variable into a static function:
drivers/net/wireless/broadcom/b43/phy_lp.c:1852:23: error: variable 'gains' is uninitialized when used here
[-Werror,-Wuninitialized]
lpphy_papd_cal(dev, gains, 0, 1, 30);
^~~~~
drivers/net/wireless/broadcom/b43/phy_lp.c:1838:2: note: variable 'gains' is declared here
struct lpphy_tx_gains gains, oldgains;
^
1 error generated.
However, this function is empty, and its arguments are never evaluated,
so gcc in contrast does not warn here. Both compilers behave in a
reasonable way as far as I can tell, so we should change the code
to avoid the warning everywhere.
We could just eliminate the lpphy_papd_cal() function entirely,
given that it has had the TODO comment in it for 10 years now
and is rather unlikely to ever get done. I'm doing a simpler
change here, and just pass the 'oldgains' variable in that has
been initialized, based on the guess that this is what was
originally meant.
Fixes: 2c0d6100da3e ("b43: LP-PHY: Begin implementing calibration & software RFKILL support") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Larry Finger <Larry.Finger@lwfinger.net> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case kmemdup fails, the fix sets conn_info->req_ie_len and
conn_info->resp_ie_len to zero to avoid buffer overflows.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/iio/common/ssp_sensors/ssp_iio.c:95:6: warning: variable
'calculated_time' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
While it isn't wrong, this will never be a problem because
iio_push_to_buffers_with_timestamp only uses calculated_time
on the same condition that it is assigned (when scan_timestamp
is not zero). While iio_push_to_buffers_with_timestamp is marked
as inline, Clang does inlining in the optimization stage, which
happens after the semantic analysis phase (plus inline is merely
a hint to the compiler).
Fix this by just zero initializing calculated_time.
Link: https://github.com/ClangBuiltLinux/linux/issues/394 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
For devices from the SigmaDelta family we need to keep CS low when doing a
conversion, since the device will use the MISO line as a interrupt to
indicate that the conversion is complete.
This is why the driver locks the SPI bus and when the SPI bus is locked
keeps as long as a conversion is going on. The current implementation gets
one small detail wrong though. CS is only de-asserted after the SPI bus is
unlocked. This means it is possible for a different SPI device on the same
bus to send a message which would be wrongfully be addressed to the
SigmaDelta device as well. Make sure that the last SPI transfer that is
done while holding the SPI bus lock de-asserts the CS signal.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Alexandru Ardelean <Alexandru.Ardelean@analog.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LLVM linker (ld.lld) defaults to removing local relocations, which
causes KASLR boot failures. ld.bfd and ld.gold already handle this
correctly. This adds the explicit instruction "--discard-none" during
the link phase. There is no change in output for ld.bfd and ld.gold,
but ld.lld now produces an image with all the needed relocations.
The call to of_find_node_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/pmac32-cpufreq.c:557:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function.
./drivers/cpufreq/pmac32-cpufreq.c:569:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 552, but without a corresponding object release within this function.
./drivers/cpufreq/pmac32-cpufreq.c:598:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 587, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: linux-pm@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_get_cpu_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/pasemi-cpufreq.c:212:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function.
./drivers/cpufreq/pasemi-cpufreq.c:220:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 147, but without a corresponding object release within this function.
The call to of_get_cpu_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function.
./drivers/cpufreq/ppc_cbe_cpufreq.c:89:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 76, but without a corresponding object release within this function.
Microphone detection provides the button detection features on the
Arizona CODECs as such it will be running if the jack is currently
inserted. If the driver is unbound whilst the jack is still inserted
this will cause warnings from the regulator framework as the MICVDD
regulator is put but was never disabled.
Correct this by disabling microphone detection on driver removal and if
the microphone detection was running disable the regulator and put the
runtime reference that was currently held.
The dev->power.direct_complete flag may become set in device_prepare() in
case the device don't have any PM callbacks (dev->power.no_pm_callbacks is
set). This leads to a broken behaviour, when there is child having wakeup
enabled and relies on its parent to be used in the wakeup path.
More precisely, when the direct complete path becomes selected for the
child in __device_suspend(), the propagation of the dev->power.wakeup_path
becomes skipped as well.
Let's address this problem, by checking if the device is a part the wakeup
path or has wakeup enabled, then prevent the direct complete path from
being used.
eSDHC-A001: The data timeout counter (SYSCTL[DTOCV]) is not
reliable for DTOCV values 0x4(2^17 SD clock), 0x8(2^21 SD clock),
and 0xC(2^25 SD clock). The data timeout counter can count from
2^13–2^27, but for values 2^17, 2^21, and 2^25, the timeout
counter counts for only 2^13 SD clocks.
A-008358: The data timeout counter value loaded into the timeout
counter is less than expected and can result into early timeout
error in case of eSDHC data transactions. The table below shows
the expected vs actual timeout period for different values of
SYSCTL[DTOCV]:
these two erratum has the same quirk to control it, and set
SDHCI_QUIRK_RESET_AFTER_REQUEST to fix above issue.
Software writing to the Transfer Type configuration register
(system clock domain) can cause a setup/hold violation in the
CRC flops (card clock domain), which can cause write accesses
to be sent with corrupt CRC values. This issue occurs only for
write preceded by read. this erratum is to fix this issue.
pwrseq_emmc.c implements a HW reset procedure for eMMC chip by driving a
GPIO line.
It registers the .reset() cb on mmc_pwrseq_ops and it registers a system
restart notification handler; both of them perform reset by unconditionally
calling gpiod_set_value().
If the eMMC reset line is tied to a GPIO controller whose driver can sleep
(i.e. I2C GPIO controller), then the kernel would spit warnings when trying
to reset the eMMC chip by means of .reset() mmc_pwrseq_ops cb (that is
exactly what I'm seeing during boot).
Furthermore, on system reset we would gets to the system restart
notification handler with disabled interrupts - local_irq_disable() is
called in machine_restart() at least on ARM/ARM64 - and we would be in
trouble when the GPIO driver tries to sleep (which indeed doesn't happen
here, likely because in my case the machine specific code doesn't call
do_kernel_restart(), I guess..).
This patch fixes the .reset() cb to make use of gpiod_set_value_cansleep(),
so that the eMMC gets reset on boot without complaints, while, since there
isn't that much we can do, we avoid register the restart handler if the
GPIO controller has a sleepy driver (and we spit a dev_notice() message to
let people know)..
This had been tested on a downstream 4.9 kernel with backported
commit 83f37ee7ba33 ("mmc: pwrseq: Add reset callback to the struct
mmc_pwrseq_ops") and commit ae60fb031cf2 ("mmc: core: Don't do eMMC HW
reset when resuming the eMMC card"), because I couldn't boot my board
otherwise. Maybe worth to RFT.
When we discover the PHY is empty in sas_rediscover_dev(), the PHY
information (like negotiated linkrate) is not updated.
As such, for a user examining sysfs for that PHY, they would see
incorrect values:
root@(none)$ cd /sys/class/sas_phy/phy-0:0:20
root@(none)$ more negotiated_linkrate
3.0 Gbit
root@(none)$ echo 0 > enable
root@(none)$ more negotiated_linkrate
3.0 Gbit
So fix this, simply discover the PHY again, even though we know it's empty;
in the above example, this gives us:
root@(none)$ more negotiated_linkrate
Phy disabled
We must do this after unregistering the device associated with the PHY
(in sas_unregister_devs_sas_addr()).
Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple
drivers is synchronized.
Fixes: e53004e20a58e ("hwmon: New f71805f driver") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: ba224e2c4f0a7 ("hwmon: New PC87427 hardware monitoring driver") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb1468 ("I2C: Move hwmon drivers (2/3)") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 8d5d45fb1468 ("I2C: Move hwmon drivers (2/3)") Reported-by: Kefeng Wang <wangkefeng.wang@huawei.com> Reported-by: John Garry <john.garry@huawei.com> Cc: John Garry <john.garry@huawei.com> Acked-by: John Garry <john.garry@huawei.com> Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Super-IO accesses may fail on a system with no or unmapped LPC bus.
Also, other drivers may attempt to access the LPC bus at the same time,
resulting in undefined behavior.
Use request_muxed_region() to ensure that IO access on the requested
address space is supported, and to ensure that access by multiple drivers
is synchronized.
Fixes: 2219cd81a6cd ("hwmon/vt1211: Add probing of alternate config index port") Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently if alloc_skb fails to allocate the skb a null skb is passed to
t4_set_arp_err_handler and this ends up dereferencing the null skb. Avoid
the NULL pointer dereference by checking for a NULL skb and returning
early.
Addresses-Coverity: ("Dereference null return") Fixes: b38a0ad8ec11 ("RDMA/cxgb4: Set arp error handler for PASS_ACCEPT_RPL messages") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Potnuri Bharat Teja <bharat@chelsio.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
clock_getres() in the vDSO library has to preserve the same behaviour
of posix_get_hrtimer_res().
In particular, posix_get_hrtimer_res() does:
sec = 0;
ns = hrtimer_resolution;
where 'hrtimer_resolution' depends on whether or not high resolution
timers are enabled, which is a runtime decision.
The vDSO incorrectly returns the constant CLOCK_REALTIME_RES. Fix this
by exposing 'hrtimer_resolution' in the vDSO datapage and returning that
instead.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
[will: Use WRITE_ONCE(), move adr off COARSE path, renumber labels, use 'w' reg] Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Modifying the VLAN stripping options when a port VLAN is configured
will break traffic for the VSI, and conceptually doesn't make sense,
so don't allow this.
Signed-off-by: Nicholas Nunley <nicholas.d.nunley@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
37fe6a42b343 ("x86: Check stack overflow in detail")
added a broad check for the full exception stack area, i.e. it considers
the full exception stack area as valid.
That's wrong in two aspects:
1) It does not check the individual areas one by one
2) #DF, NMI and #MCE are not enabling interrupts which means that a
regular device interrupt cannot happen in their context. In fact if a
device interrupt hits one of those IST stacks that's a bug because some
code path enabled interrupts while handling the exception.
Limit the check to the #DB stack and consider all other IST stacks as
'overflow' or invalid.
The SCSI core does not like to have devices or hosts unregistered
while error recovery is in progress. Trying to do so can lead to
self-deadlock: Part of the removal code tries to obtain a lock already
held by the error handler.
This can cause problems for the usb-storage and uas drivers, because
their error handler routines perform a USB reset, and if the reset
fails then the USB core automatically goes on to unbind all drivers
from the device's interfaces -- all while still in the context of the
SCSI error handler.
As it turns out, practically all the scenarios leading to a USB reset
failure end up causing a device disconnect (the main error pathway in
usb_reset_and_verify_device(), at the end of the routine, calls
hub_port_logical_disconnect() before returning). As a result, the
hub_wq thread will soon become aware of the problem and will unbind
all the device's drivers in its own context, not in the
error-handler's context.
This means that usb_reset_device() does not need to call
usb_unbind_and_rebind_marked_interfaces() in cases where
usb_reset_and_verify_device() has returned an error, because hub_wq
will take care of everything anyway.
This particular problem was observed in somewhat artificial
circumstances, by using usbfs to tell a hub to power-down a port
connected to a USB-3 mass storage device using the UAS protocol. With
the port turned off, the currently executing command timed out and the
error handler started running. The USB reset naturally failed,
because the hub port was off, and the error handler deadlocked as
described above. Not carrying out the call to
usb_unbind_and_rebind_marked_interfaces() fixes this issue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com> Tested-by: Kento Kobayashi <Kento.A.Kobayashi@sony.com> CC: Bart Van Assche <bvanassche@acm.org> CC: Martin K. Petersen <martin.petersen@oracle.com> CC: Jacky Cao <Jacky.Cao@sony.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When booted with "topology_updates=no", or when "off" is written to
/proc/powerpc/topology_updates, NUMA reassignments are inhibited for
PRRN and VPHN events. However, migration and suspend unconditionally
re-enable reassignments via start_topology_update(). This is
incoherent.
Check the topology_updates_enabled flag in
start/stop_topology_update() so that callers of those APIs need not be
aware of whether reassignments are enabled. This allows the
administrative decision on reassignments to remain in force across
migrations and suspensions.
The ctrl_check_input() function is called from pvr2_ctrl_range_check().
It's supposed to validate user supplied input and return true or false
depending on whether the input is valid or not. The problem is that
negative shifts or shifts greater than 31 are undefined in C. In
practice with GCC they result in shift wrapping so this function returns
true for some inputs which are not valid and this could result in a
buffer overflow:
drivers/media/usb/pvrusb2/pvrusb2-ctrl.c:205 pvr2_ctrl_get_valname()
warn: uncapped user index 'names[val]'
The cptr->hdw->input_allowed_mask mask is configured in pvr2_hdw_create()
and the highest valid bit is BIT(4).
Fixes: 7fb20fa38caa ("V4L/DVB (7299): pvrusb2: Improve logic which handles input choice availability") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix au0828_analog_stream_enable() to check if device is in the right
state first. When unbind happens while bind is in progress, usbdev
pointer could be invalid in au0828_analog_stream_enable() and a call
to usb_ifnum_to_if() will result in the null pointer dereference.
This problem is found with the new media_dev_allocator.sh test.
In audit_rule_change(), audit_data_to_entry() is firstly invoked to
translate the payload data to the kernel's rule representation. In
audit_data_to_entry(), depending on the audit field type, an audit tree may
be created in audit_make_tree(), which eventually invokes kmalloc() to
allocate the tree. Since this tree is a temporary tree, it will be then
freed in the following execution, e.g., audit_add_rule() if the message
type is AUDIT_ADD_RULE or audit_del_rule() if the message type is
AUDIT_DEL_RULE. However, if the message type is neither AUDIT_ADD_RULE nor
AUDIT_DEL_RULE, i.e., the default case of the switch statement, this
temporary tree is not freed.
To fix this issue, only allocate the tree when the type is AUDIT_ADD_RULE
or AUDIT_DEL_RULE.
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Reviewed-by: Richard Guy Briggs <rgb@redhat.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This driver returns an error if unsupported media bus pixel code is
requested by VIDIOC_SUBDEV_S_FMT.
But according to Documentation/media/uapi/v4l/vidioc-subdev-g-fmt.rst,
Drivers must not return an error solely because the requested format
doesn't match the device capabilities. They must instead modify the
format to match what the hardware can provide.
So select default format code and return success in that case.
In preparation for adding asynchronous subdevice support to the driver,
don't acquire v4l2_clk from the driver .probe() callback as that may
fail if the clock is provided by a bridge driver which may be not yet
initialized. Move the v4l2_clk_get() to ov6650_video_probe() helper
which is going to be converted to v4l2_subdev_internal_ops.registered()
callback, executed only when the bridge driver is ready.
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com> Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The error return value is not written by some firmware codecs, such as
MPEG-2 decode on CodaHx4. Clear the error return value before starting
the picture run to avoid misinterpreting unrelated values returned by
sequence initialization as error return value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Even if this case shouldn't happen when controller is properly programmed,
it's still better to avoid dumping a kernel Oops for this.
As the sequence may happen only for debugging purposes, log the error and
just finish the tasklet call.
The call to of_get_child_by_name returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/pinctrl/pinctrl-pistachio.c:1422:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 1360, but without a corresponding object release within this function.
According to the logitech_hidpp_2.0_specification_draft_2012-06-04.pdf doc:
https://lekensteyn.nl/files/logitech/logitech_hidpp_2.0_specification_draft_2012-06-04.pdf
We should use a register-access-protocol request using the short input /
output report ids. This is necessary because 27MHz HID++ receivers have
a max-packetsize on their HIP++ endpoint of 8, so they cannot support
long reports. Using a feature-access-protocol request (which is always
long or very-long) with these will cause a timeout error, followed by
the hidpp driver treating the device as not being HID++ capable.
This commit fixes this by switching to using a rap request to get the
protocol version.
Besides being tested with a (046d:c517) 27MHz receiver with various
27MHz keyboards and mice, this has also been tested to not cause
regressions on a non-unifying dual-HID++ nano receiver (046d:c534) with
k270 and m185 HID++-2.0 devices connected and on a unifying/dj receiver
(046d:c52b) with a HID++-2.0 Logitech Rechargeable Touchpad T650.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Randy reported objtool triggered on his (GCC-7.4) build:
lib/strncpy_from_user.o: warning: objtool: strncpy_from_user()+0x315: call to __ubsan_handle_add_overflow() with UACCESS enabled
lib/strnlen_user.o: warning: objtool: strnlen_user()+0x337: call to __ubsan_handle_sub_overflow() with UACCESS enabled
This is due to UBSAN generating signed-overflow-UB warnings where it
should not. Prior to GCC-8 UBSAN ignored -fwrapv (which the kernel
uses through -fno-strict-overflow).
Make the functions use 'unsigned long' throughout.
Reported-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: luto@kernel.org Link: http://lkml.kernel.org/r/20190424072208.754094071@infradead.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In-NMI warnings have been added to vmalloc_fault() via:
ebc8827f75 ("x86: Barf when vmalloc and kmemcheck faults happen in NMI")
back in the time when our NMI entry code could not cope with nested NMIs.
These days, it's perfectly fine to take a fault in NMI context and we
don't have to care about the fact that IRET from the fault handler might
cause NMI nesting.
This warning has already been removed from 32-bit implementation of
vmalloc_fault() in:
6863ea0cda8 ("x86/mm: Remove in_nmi() warning from vmalloc_fault()")
but the 64-bit version was omitted.
Remove the bogus warning also from 64-bit implementation of vmalloc_fault().
The test robot reported a wrong assignment of a per-CPU variable which
it detected by using sparse and sent a report. The assignment itself is
correct. The annotation for sparse was wrong and hence the report.
The first pointer is a "normal" pointer and points to the per-CPU memory
area. That means that the __percpu annotation has to be moved.
Move the __percpu annotation to pointer which points to the per-CPU
area. This change affects only the sparse tool (and is ignored by the
compiler).
Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: f97f8f06a49fe ("smpboot: Provide infrastructure for percpu hotplug threads") Link: http://lkml.kernel.org/r/20190424085253.12178-1-bigeasy@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building x86 with Clang LTO and CFI, CFI jump regions are
automatically added to the end of the .text section late in linking. As a
result, the _etext position was being labelled before the appended jump
regions, causing confusion about where the boundaries of the executable
region actually are in the running kernel, and broke at least the fault
injection code. This moves the _etext mark to outside (and immediately
after) the .text area, as it already the case on other architectures
(e.g. arm64, arm).
Currently run_cache_set() has no return value, if there is failure in
bch_journal_replay(), the caller of run_cache_set() has no idea about
such failure and just continue to execute following code after
run_cache_set(). The internal failure is triggered inside
bch_journal_replay() and being handled in async way. This behavior is
inefficient, while failure handling inside bch_journal_replay(), cache
register code is still running to start the cache set. Registering and
unregistering code running as same time may introduce some rare race
condition, and make the code to be more hard to be understood.
This patch adds return value to run_cache_set(), and returns -EIO if
bch_journal_rreplay() fails. Then caller of run_cache_set() may detect
such failure and stop registering code flow immedidately inside
register_cache_set().
If journal replay fails, run_cache_set() can report error immediately
to register_cache_set(). This patch makes the failure handling for
bch_journal_replay() be in synchronized way, easier to understand and
debug, and avoid poetential race condition for register-and-unregister
in same time.
The reason is in journal_reclaim(), when discard is enabled, we send
discard command and reclaim those journal buckets whose seq is old
than the last_seq_now, but before we write a journal with last_seq_now,
the machine is restarted, so the journal with the last_seq_now is not
written to the journal bucket, and the last_seq_wrote in the newest
journal is old than last_seq_now which we expect to be, so when we doing
replay, journals from last_seq_wrote to last_seq_now are missing.
It's hard to write a journal immediately after journal_reclaim(),
and it harmless if those missed journal are caused by discarding
since those journals are already wrote to btree node. So, if miss
seqs are started from the beginning journal, we treat it as normal,
and only print a message to show the miss journal, and point out
it maybe caused by discarding.
Patch v2 add a judgement condition to ignore the missed journal
only when discard enabled as Coly suggested.
(Coly Li: rebase the patch with other changes in bch_journal_replay())
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com> Tested-by: Dennis Schridde <devurandom@gmx.net> Signed-off-by: Coly Li <colyli@suse.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When failure happens inside bch_journal_replay(), calling
cache_set_err_on() and handling the failure in async way is not a good
idea. Because after bch_journal_replay() returns, registering code will
continue to execute following steps, and unregistering code triggered
by cache_set_err_on() is running in same time. First it is unnecessary
to handle failure and unregister cache set in an async way, second there
might be potential race condition to run register and unregister code
for same cache set.
So in this patch, if failure happens in bch_journal_replay(), we don't
call cache_set_err_on(), and just print out the same error message to
kernel message buffer, then return -EIO immediately caller. Then caller
can detect such failure and handle it in synchrnozied way.
Signed-off-by: Coly Li <colyli@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
When nbytes < 4, end is wronlgy set to a negative value which, due to
uint, is then interpreted to a large value leading to a deadlock in the
following code.
The "rate_index" is only used as an index into the phist_data->rx_rate[]
array in the mwifiex_hist_data_set() function. That array has
MWIFIEX_MAX_AC_RX_RATES (74) elements and it's used to generate some
debugfs information. The "rate_index" variable comes from the network
skb->data[] and it is a u8 so it's in the 0-255 range. We need to cap
it to prevent an array overflow.
Fixes: cbf6e05527a7 ("mwifiex: add rx histogram statistics support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
is_slave_mode defaults to false because sai structure
that contains it is kzalloc'ed.
Anyhow, if we decide to set the following configuration
SAI slave -> SAI master, is_slave_mode will remain set on true
although SAI being master it should be set to false.
Fix this by updating is_slave_mode for each call of
fsl_sai_set_dai_fmt.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com> Acked-by: Nicolin Chen <nicoleotsuka@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
FullMAC STAs have no way to update bss channel after CSA channel switch
completion. As a result, user-space tools may provide inconsistent
channel info. For instance, consider the following two commands:
$ sudo iw dev wlan0 link
$ sudo iw dev wlan0 info
The latter command gets channel info from the hardware, so most probably
its output will be correct. However the former command gets channel info
from scan cache, so its output will contain outdated channel info.
In fact, current bss channel info will not be updated until the
next [re-]connect.
Note that mac80211 STAs have a workaround for this, but it requires
access to internal cfg80211 data, see ieee80211_chswitch_work:
This patch kill instructs the DMAC to immediately terminate
execution of a thread. and then clear the interrupt status,
at last, stop generating interrupts for DMA_SEV. to guarantee
the next dma start is clean. otherwise, one interrupt maybe leave
to next start and make some mistake.
we can reporduce the problem as follows:
DMASEV: modify the event-interrupt resource, and if the INTEN sets
function as interrupt, the DMAC will set irq<event_num> HIGH to
generate interrupt. write INTCLR to clear interrupt.
>From the DS2408 datasheet [1]:
"Resume Command function checks the status of the RC flag and, if it is set,
directly transfers control to the control functions, similar to a Skip ROM
command. The only way to set the RC flag is through successfully executing
the Match ROM, Search ROM, Conditional Search ROM, or Overdrive-Match ROM
command"
The function currently works perfectly fine in a multidrop bus, but when we
have only a single slave connected, then only a Skip ROM is used and Match
ROM is not called at all. This is leading to problems e.g. with single one
DS2408 connected, as the Resume Command is not working properly and the
device is responding with failing results after the Resume Command.
This commit is fixing this by using a Skip ROM instead in those cases.
The bandwidth / performance advantage is exactly the same.
The device's remove() attempts to shut down the delayed_work scheduled
on the kernel-global workqueue by calling flush_scheduled_work().
Unfortunately, flush_scheduled_work() does not prevent the delayed_work
from re-scheduling itself. The delayed_work might run after the device
has been removed, and touch the already de-allocated info structure.
This is a potential use-after-free.
Fix by calling cancel_delayed_work_sync() during remove(): this ensures
that the delayed work is properly cancelled, is no longer running, and
is not able to re-schedule itself.
This issue was detected with the help of Coccinelle.
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If for some reason the device gives us an RX interrupt before we're
ready for it, perhaps during device power-on with misconfigured IRQ
causes mapping or so, we can crash trying to access the queues.
Prevent that by checking that we actually have RXQs and that they
were properly allocated.
When building with -Wunused-but-set-variable, the compiler shouts about
a number of pte_unmap() users, since this expands to an empty macro on
arm64:
| mm/gup.c: In function 'gup_pte_range':
| mm/gup.c:1727:16: warning: variable 'ptem' set but not used
| [-Wunused-but-set-variable]
| mm/gup.c: At top level:
| mm/memory.c: In function 'copy_pte_range':
| mm/memory.c:821:24: warning: variable 'orig_dst_pte' set but not used
| [-Wunused-but-set-variable]
| mm/memory.c:821:9: warning: variable 'orig_src_pte' set but not used
| [-Wunused-but-set-variable]
| mm/swap_state.c: In function 'swap_ra_info':
| mm/swap_state.c:641:15: warning: variable 'orig_pte' set but not used
| [-Wunused-but-set-variable]
| mm/madvise.c: In function 'madvise_free_pte_range':
| mm/madvise.c:318:9: warning: variable 'orig_pte' set but not used
| [-Wunused-but-set-variable]
Rewrite pte_unmap() as a static inline function, which silences the
warnings.
Signed-off-by: Qian Cai <cai@lca.pw> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The VDSO code uses the kernel helper that was originally designed
to abstract the access between 32 and 64bit systems. It worked so
far because this function is declared as 'inline'.
As we're about to revamp that part of the code, the VDSO would
break. Let's fix it by doing what should have been done from
the start, a proper system register access.
Reviewed-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If "ret_len" is negative then it could lead to a NULL dereference.
The "ret_len" value comes from nl80211_vendor_cmd(), if it's negative
then we don't allocate the "dcmd_buf" buffer. Then we pass "ret_len" to
brcmf_fil_cmd_data_set() where it is cast to a very high u32 value.
Most of the functions in that call tree check whether the buffer we pass
is NULL but there are at least a couple places which don't such as
brcmf_dbg_hex_dump() and brcmf_msgbuf_query_dcmd(). We memcpy() to and
from the buffer so it would result in a NULL dereference.
The fix is to change the types so that "ret_len" can't be negative. (If
we memcpy() zero bytes to NULL, that's a no-op and doesn't cause an
issue).
Fixes: 1bacb0487d0e ("brcmfmac: replace cfg80211 testmode with vendor command") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calculate the divisor for the SCR (Serial Clock Rate), avoiding
that the SSP transmission rate can be greater than the device rate.
When the division between the SSP clock and the device rate generates
a reminder, we have to increment by one the divisor.
In this way the resulting SSP clock will never be greater than the
device SPI max frequency.
For example, with:
- ssp_clk = 50 MHz
- dev freq = 15 MHz
without this patch the SSP clock will be greater than 15 MHz:
- 25 MHz for PXA25x_SSP and CE4100_SSP
- 16,56 MHz for the others
Instead, with this patch, we have in both case an SSP clock of 12.5MHz,
so the max rate of the SPI device clock is respected.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it> Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
sound/soc/fsl/imx-ssi.o: In function `imx_ssi_remove':
imx-ssi.c:(.text+0x28): undefined reference to `imx_pcm_fiq_exit'
sound/soc/fsl/imx-ssi.o: In function `imx_ssi_probe':
imx-ssi.c:(.text+0xa64): undefined reference to `imx_pcm_fiq_init'
The Kconfig warning is a result of the symbol being defined inside of
the "if SND_IMX_SOC" block, and is otherwise harmless. The link error
is more tricky and happens with SND_SOC_IMX_SSI=y, which may or may not
imply FIQ support. However, if SND_SOC_FSL_SSI is set to =m at the same
time, that selects SND_SOC_IMX_PCM_FIQ as a loadable module dependency,
which then causes a link failure from imx-ssi.
The solution here is to make SND_SOC_IMX_PCM_FIQ built-in whenever
one of its potential users is built-in.
Fixes: ff40260f79dc ("ASoC: fsl: refine DMA/FIQ dependencies") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log