The DSPS glue calls del_timer_sync() in its musb_platform_disable()
implementation, which requires the caller to not hold a lock. But
musb_remove() calls musb_platform_disable() will musb->lock held. This
could causes spinlock deadlock.
So change musb_remove() to call musb_platform_disable() without holds
musb->lock. This doesn't impact the musb_platform_disable implementation
in other glue drivers.
root@am335x-evm:~# modprobe -r musb-dsps
[ 126.134879] musb-hdrc musb-hdrc.1: remove, state 1
[ 126.140465] usb usb2: USB disconnect, device number 1
[ 126.146178] usb 2-1: USB disconnect, device number 2
[ 126.416985] musb-hdrc musb-hdrc.1: USB bus 2 deregistered
[ 126.423943]
[ 126.425525] ======================================================
[ 126.431997] [ INFO: possible circular locking dependency detected ]
[ 126.438564] 4.11.0-rc1-00003-g1557f13bca04-dirty #77 Not tainted
[ 126.444852] -------------------------------------------------------
[ 126.451414] modprobe/778 is trying to acquire lock:
[ 126.456523] (((&glue->timer))){+.-...}, at: [<c01b8788>] del_timer_sync+0x0/0xd0
[ 126.464403]
[ 126.464403] but task is already holding lock:
[ 126.470511] (&(&musb->lock)->rlock){-.-...}, at: [<bf30b7f8>] musb_remove+0x50/0x1
30 [musb_hdrc]
[ 126.479965]
[ 126.479965] which lock already depends on the new lock.
[ 126.479965]
[ 126.488531]
[ 126.488531] the existing dependency chain (in reverse order) is:
[ 126.496368]
[ 126.496368] -> #1 (&(&musb->lock)->rlock){-.-...}:
[ 126.502968] otg_timer+0x80/0xec [musb_dsps]
[ 126.507990] call_timer_fn+0xb4/0x390
[ 126.512372] expire_timers+0xf0/0x1fc
[ 126.516754] run_timer_softirq+0x80/0x178
[ 126.521511] __do_softirq+0xc4/0x554
[ 126.525802] irq_exit+0xe8/0x158
[ 126.529735] __handle_domain_irq+0x58/0xb8
[ 126.534583] __irq_usr+0x54/0x80
[ 126.538507]
[ 126.538507] -> #0 (((&glue->timer))){+.-...}:
[ 126.544636] del_timer_sync+0x40/0xd0
[ 126.549066] musb_remove+0x6c/0x130 [musb_hdrc]
[ 126.554370] platform_drv_remove+0x24/0x3c
[ 126.559206] device_release_driver_internal+0x14c/0x1e0
[ 126.565225] bus_remove_device+0xd8/0x108
[ 126.569970] device_del+0x1e4/0x308
[ 126.574170] platform_device_del+0x24/0x8c
[ 126.579006] platform_device_unregister+0xc/0x20
[ 126.584394] dsps_remove+0x14/0x30 [musb_dsps]
[ 126.589595] platform_drv_remove+0x24/0x3c
[ 126.594432] device_release_driver_internal+0x14c/0x1e0
[ 126.600450] driver_detach+0x38/0x6c
[ 126.604740] bus_remove_driver+0x4c/0xa0
[ 126.609407] SyS_delete_module+0x11c/0x1e4
[ 126.614252] __sys_trace_return+0x0/0x10
Fixes: ea2f35c01d5ea ("usb: musb: Fix sleeping function called from invalid context for hdrc glue") Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
... we don't reschedule a task under certain circumstances:
Lets say task-A, SCHED_OTHER, is running on CPU0 (and it may run only on
CPU0) and holds a PI lock. This task is removed from the CPU because it
used up its time slice and another SCHED_OTHER task is running. Task-B on
CPU1 runs at RT priority and asks for the lock owned by task-A. This
results in a priority boost for task-A. Task-B goes to sleep until the
lock has been made available. Task-A is already runnable (but not active),
so it receives no wake up.
The reality now is that task-A gets on the CPU once the scheduler decides
to remove the current task despite the fact that a high priority task is
enqueued and waiting. This may take a long time.
The desired behaviour is that CPU0 immediately reschedules after the
priority boost which made task-A the task with the lowest priority.
Suggested-by: Peter Zijlstra <peterz@infradead.org> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: fd7a4bed1835 ("sched, rt: Convert switched_{from, to}_rt() prio_changed_rt() to balance callbacks") Link: http://lkml.kernel.org/r/20170124144006.29821-1-bigeasy@linutronix.de Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filesystem encryption ostensibly supported revoking a keyring key that
had been used to "unlock" encrypted files, causing those files to become
"locked" again. This was, however, buggy for several reasons, the most
severe of which was that when key revocation happened to be detected for
an inode, its fscrypt_info was immediately freed, even while other
threads could be using it for encryption or decryption concurrently.
This could be exploited to crash the kernel or worse.
This patch fixes the use-after-free by removing the code which detects
the keyring key having been revoked, invalidated, or expired. Instead,
an encrypted inode that is "unlocked" now simply remains unlocked until
it is evicted from memory. Note that this is no worse than the case for
block device-level encryption, e.g. dm-crypt, and it still remains
possible for a privileged user to evict unused pages, inodes, and
dentries by running 'sync; echo 3 > /proc/sys/vm/drop_caches', or by
simply unmounting the filesystem. In fact, one of those actions was
already needed anyway for key revocation to work even somewhat sanely.
This change is not expected to break any applications.
In the future I'd like to implement a real API for fscrypt key
revocation that interacts sanely with ongoing filesystem operations ---
waiting for existing operations to complete and blocking new operations,
and invalidating and sanitizing key material and plaintext from the VFS
caches. But this is a hard problem, and for now this bug must be fixed.
This bug affected almost all versions of ext4, f2fs, and ubifs
encryption, and it was potentially reachable in any kernel configured
with encryption support (CONFIG_EXT4_ENCRYPTION=y,
CONFIG_EXT4_FS_ENCRYPTION=y, CONFIG_F2FS_FS_ENCRYPTION=y, or
CONFIG_UBIFS_FS_ENCRYPTION=y). Note that older kernels did not use the
shared fs/crypto/ code, but due to the potential security implications
of this bug, it may still be worthwhile to backport this fix to them.
Fixes: b7236e21d55f ("ext4 crypto: reorganize how we store keys in the inode") Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Acked-by: Michael Halcrow <mhalcrow@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill TXSTATUS, a well-defined default value is used, based on the
task's current value.
Suggested-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that if userspace supplies insufficient data to PTRACE_SETREGSET
to fill all the registers, the thread's old registers are preserved.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
regs_set() and regs_get() are vulnerable to an off-by-1 buffer overrun
if CONFIG_CPU_H8S is set, since this adds an extra entry to
register_offset[] but not to user_regs_struct.
So, iterate over user_regs_struct based on its actual size, not based on
the length of register_offset[].
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gpr_set won't work correctly and can never have been tested, and the
correct behaviour is not clear due to the endianness-dependent task
layout.
So, just remove it. The core code will now return -EOPNOTSUPPORT when
trying to set NT_PRSTATUS on this architecture until/unless a correct
implementation is supplied.
Signed-off-by: Dave Martin <Dave.Martin@arm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clearing the status bit on irq_unmask will discard any pending interrupt
that did arrive after the irq_ack, i.e. while the IRQ handler function
was executing.
Fixes: f365be092572 ("pinctrl: Add Qualcomm TLMM driver") Cc: Stephen Boyd <sboyd@codeaurora.org> Reported-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When init_vqs runs, virtio_balloon.stats is either uninitialized or
contains stale values. The host updates its state with garbage data
because it has no way of knowing that this is just a marker buffer
used for signaling.
This patch updates the stats before pushing the initial buffer.
Alternative fixes:
* Push an empty buffer in init_vqs. Not easily done with the current
virtio implementation and violates the spec "Driver MUST supply the
same subset of statistics in all buffers submitted to the statsq".
* Push a buffer with invalid tags in init_vqs. Violates the same
spec clause, plus "invalid tag" is not really defined.
Note: the spec says:
When using the legacy interface, the device SHOULD ignore all values in
the first buffer in the statsq supplied by the driver after device
initialization. Note: Historically, drivers supplied an uninitialized
buffer in the first buffer.
Unfortunately QEMU does not seem to implement the recommendation
even for the legacy interface.
Signed-off-by: Ladi Prosek <lprosek@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kees Cook has pointed out that xfrm_replay_state_esn_len() is subject to
wrapping issues. To ensure we are correctly ensuring that the two ESN
structures are the same size compare both the overall size as reported
by xfrm_replay_state_esn_len() and the internal length are the same.
When a new xfrm state is created during an XFRM_MSG_NEWSA call we
validate the user supplied replay_esn to ensure that the size is valid
and to ensure that the replay_window size is within the allocated
buffer. However later it is possible to update this replay_esn via a
XFRM_MSG_NEWAE call. There we again validate the size of the supplied
buffer matches the existing state and if so inject the contents. We do
not at this point check that the replay_window is within the allocated
memory. This leads to out-of-bounds reads and writes triggered by
netlink packets. This leads to memory corruption and the potential for
priviledge escalation.
We already attempt to validate the incoming replay information in
xfrm_new_ae() via xfrm_replay_verify_len(). This confirms that the user
is not trying to change the size of the replay state buffer which
includes the replay_esn. It however does not check the replay_window
remains within that buffer. Add validation of the contained
replay_window.
Dmitry reports following splat:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 0 PID: 13059 Comm: syz-executor1 Not tainted 4.10.0-rc7-next-20170207 #1
[..]
spin_lock_bh include/linux/spinlock.h:304 [inline]
xfrm_policy_flush+0x32/0x470 net/xfrm/xfrm_policy.c:963
xfrm_policy_fini+0xbf/0x560 net/xfrm/xfrm_policy.c:3041
xfrm_net_init+0x79f/0x9e0 net/xfrm/xfrm_policy.c:3091
ops_init+0x10a/0x530 net/core/net_namespace.c:115
setup_net+0x2ed/0x690 net/core/net_namespace.c:291
copy_net_ns+0x26c/0x530 net/core/net_namespace.c:396
create_new_namespaces+0x409/0x860 kernel/nsproxy.c:106
unshare_nsproxy_namespaces+0xae/0x1e0 kernel/nsproxy.c:205
SYSC_unshare kernel/fork.c:2281 [inline]
Problem is that when we get error during xfrm_net_init we will call
xfrm_policy_fini which will acquire xfrm_policy_lock before it was
initialized. Just move it around so locks get set up first.
one can immediatelly see an UBSAN warning:
UBSAN: Undefined behaviour in crypto/algif_hash.c:187:7
variable length array bound value 0 <= 0
CPU: 0 PID: 15949 Comm: syz-executor Tainted: G E 4.4.30-0-default #1
...
Call Trace:
...
[<ffffffff81d598fd>] ? __ubsan_handle_vla_bound_not_positive+0x13d/0x188
[<ffffffff81d597c0>] ? __ubsan_handle_out_of_bounds+0x1bc/0x1bc
[<ffffffffa0e2204d>] ? hash_accept+0x5bd/0x7d0 [algif_hash]
[<ffffffffa0e2293f>] ? hash_accept_nokey+0x3f/0x51 [algif_hash]
[<ffffffffa0e206b0>] ? hash_accept_parent_nokey+0x4a0/0x4a0 [algif_hash]
[<ffffffff8235c42b>] ? SyS_accept+0x2b/0x40
It is a correct warning, as hash state is propagated to accept as zero,
but creating a zero-length variable array is not allowed in C.
Fix this as proposed by Herbert -- do "?: 1" on that site. No sizeof or
similar happens in the code there, so we just allocate one byte even
though we do not use the array.
fbcon can deal with vc_hi_font_mask (the upper 256 chars) and adjust
the vc attrs dynamically when vc_hi_font_mask is changed at
fbcon_init(). When the vc_hi_font_mask is set, it remaps the attrs in
the existing console buffer with one bit shift up (for 9 bits), while
it remaps with one bit shift down (for 8 bits) when the value is
cleared. It works fine as long as the font gets updated after fbcon
was initialized.
However, we hit a bizarre problem when the console is switched to
another fb driver (typically from vesafb or efifb to drmfb). At
switching to the new fb driver, we temporarily rebind the console to
the dummy console, then rebind to the new driver. During the
switching, we leave the modified attrs as is. Thus, the new fbcon
takes over the old buffer as if it were to contain 8 bits chars
(although the attrs are still shifted for 9 bits), and effectively
this results in the yellow color texts instead of the original white
color, as found in the bugzilla entry below.
An easy fix for this is to re-adjust the attrs before leaving the
fbcon at con_deinit callback. Since the code to adjust the attrs is
already present in the current fbcon code, in this patch, we simply
factor out the relevant code, and call it from fbcon_deinit().
When writing the generic nonblocking commit code I assumed that
through clever lifetime management I can assure that the completion
(stored in drm_crtc_commit) only gets freed after it is completed. And
that worked.
I also wanted to make nonblocking helpers resilient against driver
bugs, by having timeouts everywhere. And that worked too.
Unfortunately taking boths things together results in oopses :( Well,
at least sometimes: What seems to happen is that the drm event hangs
around forever stuck in limbo land. The nonblocking helpers eventually
time out, move on and release it. Now the bug I tested all this
against is drivers that just entirely fail to deliver the vblank
events like they should, and in those cases the event is simply
leaked. But what seems to happen, at least sometimes, on i915 is that
the event is set up correctly, but somohow the vblank fails to fire in
time. Which means the event isn't leaked, it's still there waiting for
eventually a vblank to fire. That tends to happen when re-enabling the
pipe, and then the trap springs and the kernel oopses.
The correct fix here is simply to refcount the crtc commit to make
sure that the event sticks around even for drivers which only
sometimes fail to deliver vblanks for some arbitrary reasons. Since
crtc commits are already refcounted that's easy to do.
References: https://bugs.freedesktop.org/show_bug.cgi?id=96781 Cc: Jim Rees <rees@umich.edu> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Jani Nikula <jani.nikula@linux.intel.com> Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/20161221102331.31033-1-daniel.vetter@ffwll.ch Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sowmini pointed out Dmitry's RTNL deadlock report to me, and it turns out
to be perfectly accurate - there are various error paths that miss unlock
of the RTNL.
To fix those, change the locking a bit to not be conditional in all those
nl80211_prepare_*_dump() functions, but make those require the RTNL to
start with, and fix the buggy error paths. This also let me use sparse
(by appropriately overriding the rtnl_lock/rtnl_unlock functions) to
validate the changes.
Analogix_dp_bind() can be called from component framework, which doesn't
guarantee proper runtime PM state of the device during bind operation,
so ensure that device is runtime active before doing any register access.
This ensures that the power domain, to which DP module belongs, is turned
on. While at it, also fix the unbalanced call to phy_power_on() in
analogix_dp_bind() function.
This patch solves the following kernel oops on Samsung Exynos5250 Snow
board:
Unhandled fault: imprecise external abort (0x406) at 0x00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: : 406 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 75 Comm: kworker/0:2 Not tainted 4.9.0 #1046
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
task: ee272300 task.stack: ee312000
PC is at analogix_dp_enable_sw_function+0x18/0x2c
LR is at analogix_dp_init_dp+0x2c/0x50
...
[<c03fcb38>] (analogix_dp_enable_sw_function) from [<c03fa9c4>] (analogix_dp_init_dp+0x2c/0x50)
[<c03fa9c4>] (analogix_dp_init_dp) from [<c03fab6c>] (analogix_dp_bind+0x184/0x42c)
[<c03fab6c>] (analogix_dp_bind) from [<c03fdb84>] (component_bind_all+0xf0/0x218)
[<c03fdb84>] (component_bind_all) from [<c03ed64c>] (exynos_drm_load+0x134/0x200)
[<c03ed64c>] (exynos_drm_load) from [<c03d5058>] (drm_dev_register+0xa0/0xd0)
[<c03d5058>] (drm_dev_register) from [<c03d66b8>] (drm_platform_init+0x58/0xb0)
[<c03d66b8>] (drm_platform_init) from [<c03fe0c4>] (try_to_bring_up_master+0x14c/0x188)
[<c03fe0c4>] (try_to_bring_up_master) from [<c03fe188>] (component_add+0x88/0x138)
[<c03fe188>] (component_add) from [<c0403a38>] (platform_drv_probe+0x50/0xb0)
[<c0403a38>] (platform_drv_probe) from [<c0402470>] (driver_probe_device+0x1f0/0x2a8)
[<c0402470>] (driver_probe_device) from [<c0400a54>] (bus_for_each_drv+0x44/0x8c)
[<c0400a54>] (bus_for_each_drv) from [<c04021f8>] (__device_attach+0x9c/0x100)
[<c04021f8>] (__device_attach) from [<c04018e8>] (bus_probe_device+0x84/0x8c)
[<c04018e8>] (bus_probe_device) from [<c0401d1c>] (deferred_probe_work_func+0x60/0x8c)
[<c0401d1c>] (deferred_probe_work_func) from [<c012fc14>] (process_one_work+0x120/0x318)
[<c012fc14>] (process_one_work) from [<c012fe34>] (process_scheduled_works+0x28/0x38)
[<c012fe34>] (process_scheduled_works) from [<c0130048>] (worker_thread+0x204/0x4ac)
[<c0130048>] (worker_thread) from [<c01352c4>] (kthread+0xd8/0xf4)
[<c01352c4>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
Code: e59035f0e5935018f57ff04fe3c55001 (f57ff04e)
---[ end trace 3d1d0d87796de344 ]---
With a device dax alignment of 4KB or 2MB, I get sigbus when running
the attached fio job file for the current kernel (4.11.0-rc1+). If
I specify an alignment of 1GB, it works.
I turned on debug output, and saw that it was failing in the huge
fault code.
fio config for reproduce:
[global]
ioengine=dev-dax
direct=0
filename=/dev/dax0.0
bs=2m
[write]
rw=write
[read]
stonewall
rw=read
The driver fails to fallback when taking a fault that is larger than
the device alignment, or handling a larger fault when a smaller
mapping is already established. While we could support larger
mappings for a device with a smaller alignment, that change is
too large for the immediate fix. The simplest change is to force
fallback until the fault size matches the alignment.
Fixes: dee410792419 ("/dev/dax, core: file operations and dax-mmap") Cc: <stable@vger.kernel.org> Reported-by: Jeff Moyer <jmoyer@redhat.com> Signed-off-by: Dave Jiang <dave.jiang@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since ceph.git commit 4e28f9e63644 ("osd/OSDMap: clear osd_info,
osd_xinfo on osd deletion"), weight is set to IN when OSD is deleted.
This changes the result of applying an incremental for clients, not
just OSDs. Because CRUSH computations are obviously affected,
pre-4e28f9e63644 servers disagree with post-4e28f9e63644 clients on
object placement, resulting in misdirected requests.
When we close a channel that has been rescinded, we will leak memory since
vmbus_teardown_gpadl() returns an error. Fix this so that we can properly
cleanup the memory allocated to the ring buffers.
Fixes: ccb61f8a99e6 ("Drivers: hv: vmbus: Fix a rescind handling bug") Signed-off-by: K. Y. Srinivasan <kys@microsoft.com> Cc: Dexuan Cui <decui@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Output 'activation' may fail for the reasons of the output driver,
for example, if msc's buffer is not allocated. We forget, however,
to drop the module reference in this case. So each attempt at
activation in this case leaks a reference, preventing the module
from ever unloading.
This patch adds the missing module_put() in the activation error
path.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In journal_init_common(), if we failed to allocate the j_wbuf array, or
if we failed to create the buffer_head for the journal superblock, we
leaked the memory allocated for the revocation tables. Fix this.
Fixes: f0c9fd5458bacf7b12a9a579a727dc740cbe047e Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When iterating busy requests in timeout handler,
if the STARTED flag of one request isn't set, that means
the request is being processed in block layer or driver, and
isn't submitted to hardware yet.
In current implementation of blk_mq_check_expired(),
if the request queue becomes dying, un-started requests are
handled as being completed/freed immediately. This way is
wrong, and can cause rq corruption or double allocation[1][2],
when doing I/O and removing&resetting NVMe device at the sametime.
This patch fixes several issues reported by Yi Zhang.
Reported-by: Yi Zhang <yizhan@redhat.com> Tested-by: Yi Zhang <yizhan@redhat.com> Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Ming Lei <tom.leiming@gmail.com> Signed-off-by: Jens Axboe <axboe@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The net_cls controller controls the classid field of each socket which
is associated with the cgroup. Because the classid is per-socket
attribute, when a task migrates to another cgroup or the configured
classid of the cgroup changes, the controller needs to walk all
sockets and update the classid value, which was implemented by 3b13758f51de ("cgroups: Allow dynamically changing net_classid").
While the approach is not scalable, migrating tasks which have a lot
of fds attached to them is rare and the cost is born by the ones
initiating the operations. However, for simplicity, both the
migration and classid config change paths call update_classid() which
scans all fds of all tasks in the target css. This is an overkill for
the migration path which only needs to cover a much smaller subset of
tasks which are actually getting migrated in.
On cgroup v1, this can lead to unexpected scalability issues when one
tries to migrate a task or process into a net_cls cgroup which already
contains a lot of fds. Even if the migration traget doesn't have many
to get scanned, update_classid() ends up scanning all fds in the
target cgroup which can be extremely numerous.
Unfortunately, on cgroup v2 which doesn't use net_cls, the problem is
even worse. Before bfc2cf6f61fc ("cgroup: call subsys->*attach() only
for subsystems which are actually affected by migration"), cgroup core
would call the ->css_attach callback even for controllers which don't
see actual migration to a different css.
As net_cls is always disabled but still mounted on cgroup v2, whenever
a process is migrated on the cgroup v2 hierarchy, net_cls sees
identity migration from root to root and cgroup core used to call
->css_attach callback for those. The net_cls ->css_attach ends up
calling update_classid() on the root net_cls css to which all
processes on the system belong to as the controller isn't used. This
makes any cgroup v2 migration O(total_number_of_fds_on_the_system)
which is horrible and easily leads to noticeable stalls triggering RCU
stall warnings and so on.
The worst symptom is already fixed in upstream by bfc2cf6f61fc
("cgroup: call subsys->*attach() only for subsystems which are
actually affected by migration"); however, backporting that commit is
too invasive and we want to avoid other cases too.
This patch updates net_cls's cgrp_attach() to iterate fds of only the
processes which are actually getting migrated. This removes the
surprising migration cost which is dependent on the total number of
fds in the target cgroup. As this leaves write_classid() the only
user of update_classid(), open-code the helper into write_classid().
Reported-by: David Goode <dgoode@fb.com> Fixes: 3b13758f51de ("cgroups: Allow dynamically changing net_classid") Cc: Nina Schiff <ninasc@fb.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On CPU online the cpufreq core restores the previous governor (or
the previous "policy" setting for ->setpolicy drivers), but it does
not restore the min/max limits at the same time, which is confusing,
inconsistent and real pain for users who set the limits and then
suspend/resume the system (using full suspend), in which case the
limits are reset on all CPUs except for the boot one.
Fix this by making cpufreq_online() restore the limits when an inactive
policy is brought online.
The commit log and patch are inspired from Rafael's earlier work.
Reported-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If kernel image extends across alignment boundary, existing
code increases the KASLR offset by size of kernel image. The
offset is masked after resizing. There are cases, where after
masking, we may still have kernel image extending across
boundary. This eventually results in only 2MB block getting
mapped while creating the page tables. This results in data aborts
while accessing unmapped regions during second relocation (with
kaslr offset) in __primary_switch. To fix this problem, round up the
kernel image size, by swapper block size, before adding it for
correction.
For example consider below case, where kernel image still crosses
1GB alignment boundary, after masking the offset, which is fixed
by rounding up kernel image size.
SWAPPER_TABLE_SHIFT = 30
Swapper using section maps with section size 2MB.
CONFIG_PGTABLE_LEVELS = 3
VA_BITS = 39
On some DDR controllers, compatible with the sama5d3 one,
the sequence to enter/exit/re-enter the self-refresh mode adds
more constrains than what is currently written in the at91_idle
driver. An actual access to the DDR chip is needed between exit
and re-enter of this mode which is somehow difficult to implement.
This sequence can completely hang the SoC. It is particularly
experienced on parts which embed a L2 cache if the code run
between IDLE calls fits in it...
Moreover, as the intention is to enter and exit pretty rapidly
from IDLE, the power-down mode is a good candidate.
So now we use power-down instead of self-refresh. As we can
simplify the code for sama5d3 compatible DDR controllers,
we instantiate a new sama5d3_ddr_standby() function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com> Fixes: 017b5522d5e3 ("ARM: at91: Add new binding for sama5d3-ddramc") Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit cab43282682e ("ARM: at91/dt: sama5d2: Use new
compatible for ohci node")
It depends from commit 7150bc9b4d43 ("usb: ohci-at91: Forcibly suspend
ports while USB suspend") which was reverted and implemented
differently. With the new implementation, the compatible string must
remain the same.
The compatible string introduced by this commit has been used in the
default SAMA5D2 dtsi starting from Linux 4.8. As it has never been
working correctly in an official release, removing it should not be
breaking the stability rules.
Fixes: cab43282682e ("ARM: at91/dt: sama5d2: Use new compatible for ohci node") Signed-off-by: Romain Izard <romain.izard.pro@gmail.com> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was broken in commit cd979883b9ed ("xen/acpi-processor:
fix enabling interrupts on syscore_resume"). do_suspend (from
xen/manage.c) and thus xen_resume_notifier never get called on
the initial-domain at resume (it is if running as guest.)
The rationale for the breaking change was that upload_pm_data()
potentially does blocking work in syscore_resume(). This patch
addresses the original issue by scheduling upload_pm_data() to
execute in workqueue context.
Cc: Stanislaw Gruszka <sgruszka@redhat.com> Based-on-patch-by: Konrad Wilk <konrad.wilk@oracle.com> Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Ankur Arora <ankur.a.arora@oracle.com> Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CCP driver generally uses a round-robin approach when
assigning operations to available CCPs. For the DMA engine,
however, the DMA mappings of the SGs are associated with a
specific CCP. When an IOMMU is enabled, the IOMMU is
programmed based on this specific device.
If the DMA operations are not performed by that specific
CCP then addressing errors and I/O page faults will occur.
Update the CCP driver to allow a specific CCP device to be
requested for an operation and use this in the DMA engine
support.
Signed-off-by: Gary R Hook <gary.hook@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When PCIe FLR support was added, much of the remove/release code for
PCIe was migrated to ->down_dev(), but ->down_dev() is never called for
device removal. Let's refactor the cleanup to be done in both cases.
Also, drop the comments above mwifiex_cleanup_pcie(), because they were
clearly wrong, and it's better to have clear and obvious code than to
detail the code steps in comments anyway.
Fixes: 4c5dae59d2e9 ("mwifiex: add PCIe function level reset support") Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MP style clocks support an mux with pre-dividers. While the driver
correctly accounted for them in the .determine_rate callback, it did
not in the .recalc_rate and .set_rate callbacks.
This means when calculating the factors in the .set_rate callback, they
would be off by a factor of the active pre-divider. Same goes for
reading back the clock rate after it is set.
After commit e9afc746299d ("hwrng: geode - Use linux/io.h instead of
asm/io.h") the geode-rng driver uses devres with pci_dev->dev to keep
track of resources, but does not actually register a PCI driver. This
results in the following issues:
1. The driver leaks memory because the driver does not attach to a
device. The driver only uses the PCI device as a reference. devm_*()
functions will release resources on driver detach, which the geode-rng
driver will never do. As a result,
2. The driver cannot be reloaded because there is always a use of the
ioport and region after the first load of the driver.
Revert the changes made by e9afc746299d ("hwrng: geode - Use linux/io.h
instead of asm/io.h").
After commit 31b2a73c9c5f ("hwrng: amd - Migrate to managed API"), the
amd-rng driver uses devres with pci_dev->dev to keep track of resources,
but does not actually register a PCI driver. This results in the
following issues:
1. The message
WARNING: CPU: 2 PID: 621 at drivers/base/dd.c:349 driver_probe_device+0x38c
is output when the i2c_amd756 driver loads and attempts to register a PCI
driver. The PCI & device subsystems assume that no resources have been
registered for the device, and the WARN_ON() triggers since amd-rng has
already do so.
2. The driver leaks memory because the driver does not attach to a
device. The driver only uses the PCI device as a reference. devm_*()
functions will release resources on driver detach, which the amd-rng
driver will never do. As a result,
3. The driver cannot be reloaded because there is always a use of the
ioport and region after the first load of the driver.
Revert the changes made by 31b2a73c9c5f ("hwrng: amd - Migrate to managed
API").
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when Intel host controllers wait for the present
state to propagate.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
Disabling interrupts for even a millisecond can cause problems for some
devices. That can happen when sdhci changes clock frequency because it
waits for the clock to become stable under a spin lock.
The spin lock is not necessary here. Anything that is racing with changes
to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host.
Although the spin lock probably should be removed from the code paths that
lead to this point, such a patch would touch too much code to be suitable
for stable trees. Consequently, for this patch, just drop the spin lock
while waiting.
sdhci_arasan_get_timeout_clock() divides the frequency it has with (1 <<
(13 + divisor)).
However, the divisor is not some Arasan-specific value, but instead is
just the Data Timeout Counter Value from the SDHCI Timeout Control
Register.
Applying it here like this is wrong as the sdhci driver already takes
that value into account when calculating timeouts, and in fact it *sets*
that register value based on how long a timeout is wanted.
Additionally, sdhci core interprets the .get_timeout_clock callback
return value as if it were read from hardware registers, i.e. the unit
should be kHz or MHz depending on SDHCI_TIMEOUT_CLK_UNIT capability bit.
This bit is set at least on the tested Zynq-7000 SoC.
With the tested hardware (SDHCI_TIMEOUT_CLK_UNIT set) this results in
too high a timeout clock rate being reported, causing the core to use
longer-than-needed timeouts. Additionally, on a partitioned MMC
(therefore having erase_group_def bit set) mmc_calc_max_discard()
disables discard support as it looks like controller does not support
the long timeouts needed for that.
Do not apply the extra divisor and return the timeout clock in the
expected unit.
Tested with a Zynq-7000 SoC and a partitioned Toshiba THGBMAG5A1JBAWR
eMMC card.
The SDHCI controller in the SAMA5D2 chip requires a valid voltage set
in the power control register, otherwise commands will fail with a
timeout error.
When using the regulator framework to specify the regulator used by the
mmc device, the voltage is not configured, and it is not possible to use
the connected device.
Implement a custom 'set_power' function for this specific hardware, that
configures the voltage in the register in all cases.
We concluded there may be a window where the idle wakeup code could get
to pnv_wakeup_tb_loss() (which clobbers non-volatile GPRs), but the
hardware may set SRR1[46:47] to 01b (no state loss) which would result
in the wakeup code failing to restore non-volatile GPRs.
I was not able to trigger this condition with trivial tests on real
hardware or simulator, but the ISA (at least 2.07) seems to allow for
it, and Gautham says that it can happen if there is an exception pending
when the sleep/winkle instruction is executed.
Fixes: 1706567117ba ("powerpc/kvm: make hypervisor state restore a function") Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Acked-by: Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If ext4_convert_inline_data() was called on a directory with inline
data, the filesystem was left in an inconsistent state (as considered by
e2fsck) because the file size was not increased to cover the new block.
This happened because the inode was not marked dirty after i_disksize
was updated. Fix this by marking the inode dirty at the end of
ext4_finish_convert_inline_dir().
This bug was probably not noticed before because most users mark the
inode dirty afterwards for other reasons. But if userspace executed
FS_IOC_SET_ENCRYPTION_POLICY with invalid parameters, as exercised by
'kvm-xfstests -c adv generic/396', then the inode was never marked dirty
after updating i_disksize.
Usually every parallel port will have a single pardev registered with
it. But ppdev driver is an exception. This userspace parallel port
driver allows to create multiple parrallel port devices for a single
parallel port. And as a result we were having a nice warning like:
"sysctl table check failed:
/dev/parport/parport0/devices/ppdev0/timeslice Sysctl already exists"
Use the same logic as used in parport_register_device() and register
the proc files only once for each parallel port.
Even if bus is not hot-pluggable, devices can be unbound from the
driver via sysfs, so we should not be using __exit annotations on
remove() methods. The only exception is drivers registered with
platform_driver_probe() which specifically disables sysfs bind/unbind
attributes.
In function _hid_sensor_power_state(), when hid_sensor_read_poll_value()
is called, sensor's all properties will be updated by the value from
sensor hardware/firmware.
In some implementation, sensor hardware/firmware will do a power cycle
during S3. In this case, after resume, once hid_sensor_read_poll_value()
is called, sensor's all properties which are kept by driver during S3
will be changed to default value.
But instead, if a set feature function is called first, sensor
hardware/firmware will be recovered to the last status. So change the
sensor_hub_set_feature() calling order to behind of set feature function
to avoid sensor properties lose.
Signed-off-by: Song Hongyan <hongyan.song@intel.com> Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the IS_ENABLED() helper macro to ensure that the configfs group is
initialized either when configfs is built-in or when configfs is built as a
module. Otherwise software device creation will result in undefined
behaviour when configfs is built as a module since the configfs group for
the device not properly initialized.
Similar to commit b2f0c09664b7 ("iio: sw-trigger: Fix config group
initialization").
Fixes: 0f3a8c3f34f7 ("iio: Add support for creating IIO devices via configfs") Reported-by: Miguel Robles <miguel.robles@farole.net> Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.
If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.
According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.
To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.
Fixes: ca9a563805f7a ("iio: ti_am335x_adc: Add continuous sampling support") Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com> Signed-off-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to initialise the return value to avoid having allocation
failures going unnoticed when allocating interrupt-endpoint resources.
This prevents use-after-free or worse when the device is later unbound.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Cc: Dave Penkler <dpenkler@gmail.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USBTMC devices are required to have a bulk-in and a bulk-out endpoint,
but the driver failed to verify this, something which could lead to the
endpoint addresses being taken from uninitialised memory.
Make sure to zero all private data as part of allocation, and add the
missing endpoint sanity check.
Note that this also addresses a more recently introduced issue, where
the interrupt-in-presence flag would also be uninitialised whenever the
optional interrupt-in endpoint is not present. This in turn could lead
to an interrupt urb being allocated, initialised and submitted based on
uninitialised values.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation.") Fixes: 5b775f672cc9 ("USB: add USB test and measurement class driver") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If usb_get_bos_descriptor() returns an error, usb->bos will be NULL.
Nevertheless, it is dereferenced unconditionally in
hub_set_initial_usb2_lpm_policy() if usb2_hw_lpm_capable is set.
This results in a crash.
The CPPI 4.1 driver polls register to workaround the premature TX
interrupt issue, but it causes audio playback underrun when triggered in
Isoch transfers.
Isoch doesn't do back-to-back transfers, the TX should be done by the
time the next transfer is scheduled. So skip this polling workaround for
Isoch transfer.
Fixes: a655f481d83d6 ("usb: musb: musb_cppi41: handle pre-mature TX complete interrupt") Reported-by: Alexandre Bailon <abailon@baylibre.com> Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: Alexandre Bailon <abailon@baylibre.com> Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
This specifically fixes the NULL-pointer dereference when probing HWA HC
devices.
Fixes: df3654236e31 ("wusb: add the Wire Adapter (WA) core") Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: David Vrabel <david.vrabel@csr.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.
Note that the endpoint access that causes the NULL-deref is currently
only used for debugging purposes during probe so the oops only happens
when dynamic debugging is enabled. This means the driver could be
rewritten to continue to accept device with only two endpoints, should
such devices exist.
Some USB 2.0 devices erroneously report millisecond values in
bInterval. The generic config code manages to catch most of them,
but in some cases it's not completely enough.
The case at stake here is a USB 2.0 braille device, which wants to
announce 10ms and thus sets bInterval to 10, but with the USB 2.0
computation that yields to 64ms. It happens that one can type fast
enough to reach this interval and get the device buffers overflown,
leading to problematic latencies. The generic config code does not
catch this case because the 64ms is considered a sane enough value.
This change thus adds a USB_QUIRK_LINEAR_FRAME_INTR_BINTERVAL quirk
to mark devices which actually report milliseconds in bInterval,
and marks Vario Ultra devices as needing it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The streaming_maxburst module parameter is 0 offset (0..15)
so we must add 1 while using it for wBytesPerInterval
calculation for the SuperSpeed companion descriptor.
Without this host uvcvideo driver will always see the wrong
wBytesPerInterval for SuperSpeed uvc gadget and may not find
a suitable video interface endpoint.
e.g. for streaming_maxburst = 0 case it will always
fail as wBytePerInterval was evaluating to 0.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget code exports the bitfield for serial status changes
over the wire in its internal endianness. The fix is to convert
to little endian before sending it over the wire.
Add Quectel UC15, UC20, EC21, and EC25. The EC20 is handled by
qcserial due to a USB VID/PID conflict with an existing Acer
device.
Signed-off-by: Dan Williams <dcbw@redhat.com> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new Dell laptop needs to apply ALC269_FIXUP_DELL1_MIC_NO_PRESENCE to
fix the headset problem, and the pin definiton of this machine is not
in the pin quirk table yet, now adding it to the table.
In the commit [15c75b09f8d1: ALSA: ctxfi: Fallback DMA mask to 32bit],
I forgot to put "!" at dam_set_mask() call check in cthw20k1.c (while
cthw20k2.c is OK). This patch fixes that obvious bug.
(As a side note: although the original commit was completely wrong,
it's still working for most of machines, as it sets to 32bit DMA mask
in the end. So the bug severity is low.)
When snd_seq_pool_done() is called, it marks the closing flag to
refuse the further cell insertions. But snd_seq_pool_done() itself
doesn't clear the cells but just waits until all cells are cleared by
the caller side. That is, it's racy, and this leads to the endless
stall as syzkaller spotted.
This patch addresses the racy by splitting the setup of pool->closing
flag out of snd_seq_pool_done(), and calling it properly before
snd_seq_pool_done().
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer should a malicious device lack endpoints.
Fixes: c04148f915e5 ("Input: add driver for USB VoIP phones with CM109...") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory that lie beyond the end of the endpoint
array should a malicious device lack the expected endpoints.
EeeBook X205TA is yet another ASUS device with a special touchpad
firmware that needs to be accounted for during initialization, or
else the touchpad will go into an invalid state upon suspend/resume.
Adding the appropriate ic_type and product_id check fixes the problem.
Devices identified as E7="73 03 28" use slightly modified version of V8
protocol, with lower count per electrode, different offsets, and different
feature bits in OTP data.
Fixes: aeaa881f9b17 ("Input: ALPS - set DualPoint flag for 74 03 28 devices") Signed-off-by: Masaki Ota <masaki.ota@jp.alps.com> Acked-by: Pali Rohar <pali.rohar@gmail.com> Tested-by: Paul Donohue <linux-kernel@PaulSD.com> Tested-by: Nick Fletcher <nick.m.fletcher@gmail.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
icsk_ack.lrcvtime has a 0 value at socket creation time.
tcpi_last_data_recv can have bogus value if no payload is ever received.
This patch initializes icsk_ack.lrcvtime for active sessions
in tcp_finish_connect(), and for passive sessions in
tcp_create_openreq_child()
Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In sk_clone_lock(), we create a new socket and inherit most of the
parent's members via sock_copy() which memcpy()'s various sections.
Now, in case the parent socket had a BPF socket filter attached,
then newsk->sk_filter points to the same instance as the original
sk->sk_filter.
sk_filter_charge() is then called on the newsk->sk_filter to take a
reference and should that fail due to hitting max optmem, we bail
out and release the newsk instance.
The issue is that commit 278571baca2a ("net: filter: simplify socket
charging") wrongly combined the dismantle path with the failure path
of xfrm_sk_clone_policy(). This means, even when charging failed, we
call sk_free_unlock_clone() on the newsk, which then still points to
the same sk_filter as the original sk.
Thus, sk_free_unlock_clone() calls into __sk_destruct() eventually
where it tests for present sk_filter and calls sk_filter_uncharge()
on it, which potentially lets sk_omem_alloc wrap around and releases
the eBPF prog and sk_filter structure from the (still intact) parent.
Fix it by making sure that when sk_filter_charge() failed, we reset
newsk->sk_filter back to NULL before passing to sk_free_unlock_clone(),
so that we don't mess with the parents sk_filter.
Only if xfrm_sk_clone_policy() fails, we did reach the point where
either the parent's filter was NULL and as a result newsk's as well
or where we previously had a successful sk_filter_charge(), thus for
that case, we do need sk_filter_uncharge() to release the prior taken
reference on sk_filter.
Fixes: 278571baca2a ("net: filter: simplify socket charging") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander reported a KMSAN splat caused by reads of uninitialized
field (tb_id_in) from user provided struct fib_result_nl
It turns out nl_fib_input() sanity tests on user input is a bit
wrong :
User can pretend nlh->nlmsg_len is big enough, but provide
at sendmsg() time a too small buffer.
Reported-by: Alexander Potapenko <glider@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
removed the bcmgenet_mii_reset() function from bcmgenet_power_up() and
bcmgenet_internal_phy_setup() functions. In so doing it broke the reset
of the internal PHY devices used by the GENETv1-GENETv3 which required
this reset before the UniMAC was enabled. It also broke the internal
GPHY devices used by the GENETv4 because the config_init that installed
the AFE workaround was no longer occurring after the reset of the GPHY
performed by bcmgenet_phy_power_set() in bcmgenet_internal_phy_setup().
In addition the code in bcmgenet_internal_phy_setup() related to the
"enable APD" comment goes with the bcmgenet_mii_reset() so it should
have also been removed.
Commit bd4060a6108b ("net: bcmgenet: Power on integrated GPHY in
bcmgenet_power_up()") moved the bcmgenet_phy_power_set() call to the
bcmgenet_power_up() function, but failed to remove it from the
bcmgenet_internal_phy_setup() function. Had it done so, the
bcmgenet_internal_phy_setup() function would have been empty and could
have been removed at that time.
Commit 5dbebbb44a6a ("net: bcmgenet: Software reset EPHY after power on")
was submitted to correct the functional problems introduced by
commit 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset"). It
was included in v4.4 and made available on 4.3-stable. Unfortunately,
it didn't fully revert the commit because this bcmgenet_mii_reset()
doesn't apply the soft reset to the internal GPHY used by GENETv4 like
the previous one did. This prevents the restoration of the AFE work-
arounds for internal GPHY devices after the bcmgenet_phy_power_set() in
bcmgenet_internal_phy_setup().
This commit takes the alternate approach of removing the unnecessary
bcmgenet_internal_phy_setup() function which shouldn't have been in v4.3
so that when bcmgenet_mii_reset() was restored it should have only gone
into bcmgenet_power_up(). This will avoid the problems while also
removing the redundancy (and hopefully some of the confusion).
Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset") Signed-off-by: Doug Berger <opendmb@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case udp_sk(sk)->pending is AF_INET6, udpv6_sendmsg() would
jump to do_append_data, skipping the initialization of sockc.tsflags.
Fix the problem by moving sockc.tsflags initialization earlier.
The bug was detected with KMSAN.
Fixes: c14ac9451c34 ("sock: enable timestamping using control messages") Signed-off-by: Alexander Potapenko <glider@google.com> Acked-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0baee ("net/mlx5: Ethernet Datapath files") Signed-off-by: Gal Pressman <galp@mellanox.com> Cc: kernel-team@fb.com Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97dba9e ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23d1 ('net/mlx5: Rate limit tables support') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The VRF driver takes a reference to the inet6_dev on the VRF device for
its rt6_local dst when handling local traffic through the VRF device as
a loopback. When the device is deleted the driver does a put on the idev
but does not reset rt6i_idev in the rt6_info struct. When the dst is
destroyed, dst_destroy calls ip6_dst_destroy which does a second put for
what is essentially the same reference causing it to be prematurely freed.
Reset rt6i_idev after the put in the vrf driver.
Fixes: b4869aa2f881e ("net: vrf: ipv6 support for local traffic to
local addresses") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a Dell branded Sierra Wireless EM7455. It is operating in
MBIM mode by default, but can be configured to provide two QMI/RMNET
functions.
Signed-off-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dmitry has reported that a BUG_ON() condition in unix_notinflight()
may be triggered by a simple code that forwards unix socket in an
SCM_RIGHTS message.
That is caused by incorrect unix socket GC implementation in unix_gc().
The GC first collects list of candidates, then (a) decrements their
"children's" inflight counter, (b) checks which inflight counters are
now 0, and then (c) increments all inflight counters back.
(a) and (c) are done by calling scan_children() with inc_inflight or
dec_inflight as the second argument.
Commit 6209344f5a37 ("net: unix: fix inflight counting bug in garbage
collector") changed scan_children() such that it no longer considers
sockets that do not have UNIX_GC_CANDIDATE flag. It also added a block
of code that that unsets this flag _before_ invoking
scan_children(, dec_iflight, ). This may lead to incorrect inflight
counters for some sockets.
This change fixes this bug by changing order of operations:
UNIX_GC_CANDIDATE is now unset only after all inflight counters are
restored to the original state.
projects / linux-stable / log