A number of our uaccess routines ('__arch_clear_user()' and
'__arch_copy_{in,from,to}_user()') fail to re-enable PAN if they
encounter an unhandled fault whilst accessing userspace.
For CPUs implementing both hardware PAN and UAO, this bug has no effect
when both extensions are in use by the kernel.
For CPUs implementing hardware PAN but not UAO, this means that a kernel
using hardware PAN may execute portions of code with PAN inadvertently
disabled, opening us up to potential security vulnerabilities that rely
on userspace access from within the kernel which would usually be
prevented by this mechanism. In other words, parts of the kernel run the
same way as they would on a CPU without PAN implemented/emulated at all.
For CPUs not implementing hardware PAN and instead relying on software
emulation via 'CONFIG_ARM64_SW_TTBR0_PAN=y', the impact is unfortunately
much worse. Calling 'schedule()' with software PAN disabled means that
the next task will execute in the kernel using the page-table and ASID
of the previous process even after 'switch_mm()', since the actual
hardware switch is deferred until return to userspace. At this point, or
if there is a intermediate call to 'uaccess_enable()', the page-table
and ASID of the new process are installed. Sadly, due to the changes
introduced by KPTI, this is not an atomic operation and there is a very
small window (two instructions) where the CPU is configured with the
page-table of the old task and the ASID of the new task; a speculative
access in this state is disastrous because it would corrupt the TLB
entries for the new task with mappings from the previous address space.
As Pavel explains:
| I was able to reproduce memory corruption problem on Broadcom's SoC
| ARMv8-A like this:
|
| Enable software perf-events with PERF_SAMPLE_CALLCHAIN so userland's
| stack is accessed and copied.
|
| The test program performed the following on every CPU and forking
| many processes:
|
| unsigned long *map = mmap(NULL, PAGE_SIZE, PROT_READ|PROT_WRITE,
| MAP_SHARED | MAP_ANONYMOUS, -1, 0);
| map[0] = getpid();
| sched_yield();
| if (map[0] != getpid()) {
| fprintf(stderr, "Corruption detected!");
| }
| munmap(map, PAGE_SIZE);
|
| From time to time I was getting map[0] to contain pid for a
| different process.
Ensure that PAN is re-enabled when returning after an unhandled user
fault from our uaccess routines.
Cc: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Mark Rutland <mark.rutland@arm.com> Tested-by: Mark Rutland <mark.rutland@arm.com> Cc: <stable@vger.kernel.org> Fixes: 338d4f49d6f7 ("arm64: kernel: Add support for Privileged Access Never") Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
[will: rewrote commit message]
[will: backport for 4.9.y stable kernels] Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com> Signed-off-by: Emil Renner Berthing <kernel@esmil.dk> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The three INA3221_CONFIG_MODE macros are not correctly defined here.
The MODE3-1 bits are located at BIT 2-0 according to the datasheet.
So this patch just fixes them by shifting all of them with a correct
offset. However, this isn't a crital bug fix as the driver does not
use any of them at this point.
Currently accessing various /sys/fs/orangefs files will spam the
kernel log with the following info message when the client is not
running:
[ 491.489284] sysfs_service_op_show: Client not running :-5:
Rate limit this info message to make it less spammy.
Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Mike Marshall <hubcap@omnibond.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On at least x86 and ARM64, and as documented in the ptrace man page
a skipped system call will still cause a syscall exit ptrace stop.
Previous to this commit 32-bit ARM did not, resulting in strace
being confused when seccomp skips system calls.
This change also impacts programs that use ptrace to skip system calls.
Fixes: ad75b51459ae ("ARM: 7579/1: arch/allow a scno of -1 to not cause a SIGILL") Signed-off-by: Timothy E Baldwin <T.E.Baldwin99@members.leeds.ac.uk> Signed-off-by: Eugene Syromyatnikov <evgsyr@gmail.com> Reviewed-by: Kees Cook <keescook@chromium.org> Tested-by: Kees Cook <keescook@chromium.org> Tested-by: Eugene Syromyatnikov <evgsyr@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
spidev will make a big fuss if a device tree node binds a device by
using "spidev" as the node's compatible property.
However, the logic for this isn't looking for "spidev" in the
compatible, but rather checking that the device is NOT compatible with
spidev's list of devices.
This causes a false positive if a device not named "rohm,dh2228fv", etc.
binds to spidev, even if a means other than putting "spidev" in the
device tree was used. E.g., the sysfs driver_override attribute.
Signed-off-by: Trent Piepho <tpiepho@impinj.com> Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz> Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The priv->data->set can be NULL while flags contains GPIO_SYSCON_FEAT_OUT
and chip->set is valid pointer. This happens in case the controller uses
the default GPIO setter. Always use chip->set to access the setter to avoid
possible NULL pointer dereferencing.
Shifting the u8 value[3] by an int can lead to sign-extension
overflow. For example, if value[3] is 0xff and the shift is 24 then it
is promoted to int and then the top bit is sign-extended so that all
upper 32 bits are set. Fix this by casting value[3] to a u32 before
the shift.
Detected by CoverityScan, CID#1016522 ("Unintended sign extension")
Fixes: e0d3bafd0258 ("V4L/DVB (10954): Add cx231xx USB driver") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Flushing the workqueue can cause operations to happen which might
call gfs2_log_reserve(), or get stuck waiting for locks taken by such
operations. gfs2_log_reserve() can io_schedule(). If this happens, it
will never wake because the only thing which can wake it is gfs2_logd()
which was already stopped.
This causes umount of a gfs2 filesystem to wedge permanently if, for
example, the umount immediately follows a large delete operation.
When this occured, the following stack trace was obtained from the
umount command
Signed-off-by: Tim Smith <tim.smith@citrix.com> Signed-off-by: Mark Syms <mark.syms@citrix.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In isif_probe(), there is a while loop to get the ISIF base address and
linearization table0 and table1 address. In the loop body, the function
platform_get_resource() is called to get the resource. If
platform_get_resource() returns NULL, the loop is terminated and the
execution goes to 'fail_nobase_res'. Suppose the loop is terminated at the
first iteration because platform_get_resource() returns NULL and the
execution goes to 'fail_nobase_res'. Given that there is another while loop
at 'fail_nobase_res' and i equals to 0, one iteration of the second while
loop will be executed. However, the second while loop does not check the
return value of platform_get_resource(). This can cause a NULL pointer
dereference bug if the return value is a NULL pointer.
This patch avoids the above issue by adding a check in the second while
loop after the call to platform_get_resource().
Signed-off-by: Wenwen Wang <wang6495@umn.edu> Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a child device like touchscreen is wakeup capable, then keep ADC
interface on, so that a touching resistive screen will generate wakeup
event to the system.
Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns that the address of a pointer will always evaluated as true
in a boolean context.
drivers/video/backlight/lm3639_bl.c:403:14: warning: address of
'pchip->cdev_torch' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (&pchip->cdev_torch)
~~ ~~~~~~~^~~~~~~~~~
drivers/video/backlight/lm3639_bl.c:405:14: warning: address of
'pchip->cdev_flash' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (&pchip->cdev_flash)
~~ ~~~~~~~^~~~~~~~~~
2 warnings generated.
These statements have been present since 2012, introduced by
commit 0f59858d5119 ("backlight: add new lm3639 backlight
driver"). Given that they have been called unconditionally since
then presumably without any issues, removing the always true if
statements to fix the warnings without any real world changes.
Link: https://github.com/ClangBuiltLinux/linux/issues/119 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Lianbo reported a build error with a particular 32-bit config, see Link
below for details.
Provide a weak copy_oldmem_page_encrypted() function which architectures
can override, in the same manner other functionality in that file is
supplied.
I'm not sure why the code assumes that only the first put_user() needs
an access_ok() check. I have made all the put_user() and get_user()
calls checked.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Philippe Ombredanne <pombredanne@nexb.com> Cc: Mathieu Malaterre <malat@debian.org> Cc: Peter Malone <peter.malone@gmail.com>, Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed. Note that RSC is sent separately in
a new command. This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
There was a small race when removing the sbshc module where
smbus_alarm() had queued acpi_smbus_callback() for deferred execution
but it hadn't been run yet, so that when it did run hc had been freed
and the module unloaded, resulting in an invalid paging request.
A similar race existed when removing the sbs module with regards to
acpi_sbs_callback() (which is called from acpi_smbus_callback()).
We therefore need to ensure no callbacks are pending or executing before
the cleanups are done and the modules are removed.
Signed-off-by: Ronald Tschalär <ronald@innovation.ch> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The DCP driver does not obey cryptlen, when doing android CTS this
results in passing to hardware input stream lengths which are not
multiple of block size.
Add a check to prevent future erroneous stream lengths from reaching the
hardware and adjust the scatterlist walking code to obey cryptlen.
Also properly copy-out the IV for chaining.
Signed-off-by: Radu Solea <radu.solea@nxp.com> Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com> Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building a 32-bit config which has the above MFD item as module
but OLPC_XO1_PM is enabled =y - which is bool, btw - the kernel fails
building with:
ld: arch/x86/platform/olpc/olpc-xo1-pm.o: in function `xo1_pm_remove':
/home/boris/kernel/linux/arch/x86/platform/olpc/olpc-xo1-pm.c:159: undefined reference to `mfd_cell_disable'
ld: arch/x86/platform/olpc/olpc-xo1-pm.o: in function `xo1_pm_probe':
/home/boris/kernel/linux/arch/x86/platform/olpc/olpc-xo1-pm.c:133: undefined reference to `mfd_cell_enable'
make: *** [Makefile:1030: vmlinux] Error 1
A certain silead controller (Chip ID: 0x56810000) loses its firmware
after suspend, causing the resume to fail. This patch tries to load
the firmware, should a resume error occur and retries the resuming.
Signed-off-by: Julian Sax <jsbc@gmx.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Running "./nfstest_delegation --runtest recall26" uncovers that
client doesn't recover the lock when we have an appending open,
where the initial open got a write delegation.
Instead of checking for the passed in open context against
the file lock's open context. Check that the state is the same.
ARCH_BCM_63XX which is used by ARM-based DSL SoCs from Broadcom uses the
same controller, make it possible to select the STB driver and update
the Kconfig and help text a bit.
clk_notifier_register() documentation states, that the provided notifier
callbacks associated with the notifier must not re-enter into the clk
framework by calling any top-level clk APIs. Fix this by replacing
clk_get_rate() calls with clk_hw_get_rate(), which is safe in this
context.
The driver sends an action frame down and waits for a completion signal
triggered by the received BRCMF_E_ACTION_FRAME_OFF_CHAN_COMPLETE event
to continue the process. However, the action frame could be transmitted
either on the current channel or on an off channel. For the on-channel
case, only BRCMF_E_ACTION_FRAME_COMPLETE event will be received when
the frame is transmitted, which make the driver always wait a full
timeout duration. This patch has the completion signal be triggered by
receiving the BRCMF_E_ACTION_FRAME_COMPLETE event for the on-channel
case.
This change fixes WFA p2p certification 5.1.19 failure.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Finding a common channel to send an action frame out is required for
some action types. Since a loop with several scan retry is used to find
the channel, a short wait time could be considered for each attempt.
This patch reduces the wait time from 1500 to 450 msec for each action
frame scan.
This patch fixes the WFA p2p certification 5.1.20 failure caused by the
long action frame send time.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com> Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When booting with "nosmt=force" a message is issued into dmesg to
confirm that SMT has been force-disabled but such a message is not
issued when only "nosmt" is on the kernel command line.
During probe, if there was an error the memory region and the memory
map were not properly released.This can lead a system unusable if
deferred probe is in use.
Replace mem_request and map with devm_ioremap_resource
Fix interrupt-out transfer length which was being set to the
transfer-buffer length rather than the size of the outgoing packet.
Note that no slab data was leaked as the whole transfer buffer is always
cleared before each transfer.
Fixes: 9aa8dae7b1fa ("cypress_m8: use usb_fill_int_urb where appropriate") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an OS (currently only classic Mac OS) is running in KVM-PR and makes a
linked jump from code with split hack addressing enabled into code that does
not, LR is not correctly updated and reflects the previously munged PC.
To fix this, this patch undoes the address munge when exiting split
hack mode so that code relying on LR being a proper address will now
execute. This does not affect OS X or other operating systems running
on KVM-PR.
Signed-off-by: Cameron Kaiser <spectre@floodgap.com> Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Elo VuPoint 15MX has two headphone jacks of which neither work by
default. Disabling automute allows ALSA to work normally with the
speakers & left headphone jack.
Future pin configuration changes may be required in the future to get
the right headphone jack working in tandem.
Clang warns when one enumerated type is implicitly converted to another.
drivers/ata/pata_ep93xx.c:662:36: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
drv_data->dma_rx_data.direction = DMA_FROM_DEVICE;
~ ^~~~~~~~~~~~~~~
drivers/ata/pata_ep93xx.c:670:36: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
drv_data->dma_tx_data.direction = DMA_TO_DEVICE;
~ ^~~~~~~~~~~~~
drivers/ata/pata_ep93xx.c:681:19: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
conf.direction = DMA_FROM_DEVICE;
~ ^~~~~~~~~~~~~~~
drivers/ata/pata_ep93xx.c:692:19: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
conf.direction = DMA_TO_DEVICE;
~ ^~~~~~~~~~~~~
Use the equivalent valued enums from the expected type so that Clang no
longer warns about a conversion.
These address spaces are defined by the ACPI spec to be
"always available", and thus _REG should never be run on them.
Provides compatibility with other ACPI implementations.
Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Erik Schmauss <erik.schmauss@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/infiniband/hw/mlx4/mad.c:1811:41: warning: implicit conversion
from enumeration type 'enum mlx4_ib_qp_flags' to different enumeration
type 'enum ib_qp_create_flags' [-Wenum-conversion]
qp_init_attr.init_attr.create_flags = MLX4_IB_SRIOV_TUNNEL_QP;
~ ^~~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/mlx4/mad.c:1819:41: warning: implicit conversion
from enumeration type 'enum mlx4_ib_qp_flags' to different enumeration
type 'enum ib_qp_create_flags' [-Wenum-conversion]
qp_init_attr.init_attr.create_flags = MLX4_IB_SRIOV_SQP;
~ ^~~~~~~~~~~~~~~~~
The type mlx4_ib_qp_flags explicitly provides supplemental values to the
type ib_qp_create_flags. Make that clear to Clang by changing the
create_flags type to u32.
Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Jason Gunthorpe <jgg@mellanox.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fix crash when we have restore flow director filters after reset
adapter. In ixgbe_fdir_filter_restore() filter->action is outside of the
rx_ring array, as it has a VF identifier in the upper 32 bits.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is converted implicitly to another:
drivers/mtd/nand/raw/sh_flctl.c:483:46: warning: implicit conversion
from enumeration type 'enum dma_transfer_direction' to different
enumeration type 'enum dma_data_direction' [-Wenum-conversion]
flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_DEV_TO_MEM) > 0)
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
drivers/mtd/nand/raw/sh_flctl.c:542:46: warning: implicit conversion
from enumeration type 'enum dma_transfer_direction' to different
enumeration type 'enum dma_data_direction' [-Wenum-conversion]
flctl_dma_fifo0_transfer(flctl, buf, rlen, DMA_MEM_TO_DEV) > 0)
~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_data_direction to satisfy Clang.
When CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not set, we look up dtl_idx in
the lppaca to determine the number of entries in the buffer. Since
lppaca is in big endian, we need to do an endian conversion before using
this in our calculation to determine the number of entries in the
buffer. Without this, we do not iterate over the existing entries in the
DTL buffer properly.
When CONFIG_VIRT_CPU_ACCOUNTING_NATIVE is not set, we register the DTL
buffer for a cpu when the associated file under powerpc/dtl in debugfs
is opened. When doing so, we need to set the size of the buffer being
registered in the second u32 word of the buffer. This needs to be in big
endian, but we are not doing the conversion resulting in the below error
showing up in dmesg:
dtl_start: DTL registration for cpu 0 (hw 0) failed with -4
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:390:4: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
IEEE_FAUX_SYNC(dev, dcb);
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.h:70:10: note: expanded
from macro 'IEEE_FAUX_SYNC'
CXGB4_DCB_STATE_FW_ALLSYNCED);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
Use the equivalent value of the expected type to silence Clang while
resulting in no functional change.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:303:7: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
? CXGB4_DCB_STATE_FW_ALLSYNCED
^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4/cxgb4_dcb.c:304:7: warning: implicit
conversion from enumeration type 'enum cxgb4_dcb_state' to different
enumeration type 'enum cxgb4_dcb_state_input' [-Wenum-conversion]
: CXGB4_DCB_STATE_FW_INCOMPLETE);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2 warnings generated.
Use the equivalent value of the expected type to silence Clang while
resulting in no functional change.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when implicitly converting from one enumerated type to
another. Avoid this by using the equivalent value from the expected
type.
drivers/dma/timb_dma.c:548:27: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
td_desc->desc_list_len, DMA_MEM_TO_DEV);
^~~~~~~~~~~~~~
1 warning generated.
Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang warns when implicitly converting from one enumerated type to
another. Avoid this by using the equivalent value from the expected
type.
In file included from drivers/dma/ep93xx_dma.c:30:
./include/linux/platform_data/dma-ep93xx.h:88:10: warning: implicit
conversion from enumeration type 'enum dma_data_direction' to different
enumeration type 'enum dma_transfer_direction' [-Wenum-conversion]
return DMA_NONE;
~~~~~~ ^~~~~~~~
1 warning generated.
Reported-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use the NL80211_KEY_IDX attribute inside the NL80211_ATTR_KEY in
NL80211_CMD_GET_KEY responses to comply with nl80211_key_policy.
This is unlikely to affect existing userspace.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since the debug print code is outside of the loop, it shouldn't use the loop
iterator anymore but instead print the found maximum index.
Cc: Nick Kossifidis <mickflemm@gmail.com> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The vdev-start-response message should cause the
completion to fire, even in the error case. Otherwise,
the user still gets no useful information and everything
is blocked until the timeout period.
Add some warning text to print out the invalid status
code to aid debugging, and propagate failure code.
Signed-off-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dummy node ID is marked into all memory ranges on the system. So the
dummy node really extends the entire memblock.memory. Hence report correct
extent information for the dummy node using memblock range helper functions
instead of the range [0LLU, PFN_PHYS(max_pfn) - 1)].
Fixes: 1a2db30034 ("arm64, numa: Add NUMA support for arm64 platforms") Acked-by: Punit Agrawal <punit.agrawal@arm.com> Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
So far we have only supported 3 level page table with fixed IPA of
40bits, where PUD is folded. With 4 level page tables, we need
to check if the PUD entry is valid or not. Fix stage2_flush_memslot()
to do this check, before walking down the table.
Acked-by: Christoffer Dall <cdall@kernel.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Reviewed-by: Eric Auger <eric.auger@redhat.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix up the priority queue to not batch by owner, but by queue, so that
we allow '1 << priority' elements to be dequeued before switching to
the next priority queue.
The owner field is still used to wake up requests in round robin order
by owner to avoid single processes hogging the RPC layer by loading the
queues.
Since SMPS10 and OTG cable detection extcon are described here, and
work to enable OTG power when an OTG cable is plugged in, we can
define OTG mode in the controller (which is disabled by default in
omap5.dtsi).
Tested on OMAP5EVM and Pyra.
Suggested-by: Roger Quadros <rogerq@ti.com> Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For passthrough requests, libata-scsi takes what the user passes in
as gospel. This can be problematic if the user fills in the CDB
incorrectly. One example of that is in request sizes. For read/write
commands, the CDB contains fields describing the transfer length of
the request. These should match with the SG_IO header fields, but
libata-scsi currently does no validation of that.
Check that the number of blocks in the CDB for passthrough requests
matches what was mapped into the request. If the CDB asks for more
data then the validated SG_IO header fields, error it.
This can be used to check for fs vs non-fs requests and basically
removes all knowledge of BLOCK_PC specific from the block layer,
as well as preparing for removing the cmd_type field in struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@fb.com>
[only take the blkdev.h changes as we only want the function for backported
patches - gregkh] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Also with this gone we can remove the cea_modes db. This entire thing
is massively incomplete anyway, compared to the CEA parsing that
drm_edid.c does.
Since MOV SS and POP SS instructions will delay the exceptions until the
next instruction is executed, single-stepping on it by uprobes must be
prohibited.
uprobe already rejects probing on POP SS (0x1f), but allows probing on MOV
SS (0x8e and reg == 2). This checks the target instruction and if it is
MOV SS or POP SS, returns -ENOTSUPP to reject probing.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Oleg Nesterov <oleg@redhat.com> Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Cc: Francis Deslauriers <francis.deslauriers@efficios.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Yonghong Song <yhs@fb.com> Cc: Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: "David S . Miller" <davem@davemloft.net> Link: https://lkml.kernel.org/r/152587072544.17316.5950935243917346341.stgit@devbox Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since MOV SS and POP SS instructions will delay the exceptions until the
next instruction is executed, single-stepping on it by kprobes must be
prohibited.
However, kprobes usually executes those instructions directly on trampoline
buffer (a.k.a. kprobe-booster), except for the kprobes which has
post_handler. Thus if kprobe user probes MOV SS with post_handler, it will
do single-stepping on the MOV SS.
This means it is safe that if it is used via ftrace or perf/bpf since those
don't use the post_handler.
Anyway, since the stack switching is a rare case, it is safer just
rejecting kprobes on such instructions.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com> Cc: Francis Deslauriers <francis.deslauriers@efficios.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Alexei Starovoitov <ast@kernel.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Andy Lutomirski <luto@kernel.org> Cc: "H . Peter Anvin" <hpa@zytor.com> Cc: Yonghong Song <yhs@fb.com> Cc: Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: "David S . Miller" <davem@davemloft.net> Link: https://lkml.kernel.org/r/152587069574.17316.3311695234863248641.stgit@devbox Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recent probing at the Linux Kernel Memory Model uncovered a
'surprise'. Strongly ordered architectures where the atomic RmW
primitive implies full memory ordering and
smp_mb__{before,after}_atomic() are a simple barrier() (such as x86)
fail for:
Because, while the atomic_inc() implies memory order, it
(surprisingly) does not provide a compiler barrier. This then allows
the compiler to re-order like so:
This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.
Fixes: 332f989a3b00 ("CDC-NCM: handle incomplete transfer of MTU") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since they are of unsigned int type, it's allowed to read them
unlocked during reporting to userspace. Let's underline this fact
with READ_ONCE() macroses.
dtc has new checks for SPI buses. Fix the warnings in node names.
arch/arm64/boot/dts/amd/amd-overdrive.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b0.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
arch/arm64/boot/dts/amd/amd-overdrive-rev-b1.dtb: Warning (spi_bus_bridge): /smb/ssp@e1030000: node name for SPI buses should be 'spi'
The X3T9.2 specification (draft) says, under "6.1.4.2 RESELECTION time-out
procedure", that a target may assert RST or go to BUS FREE phase if the
initiator does not respond within 200 us. Something like this has been
observed with AztecMonster II target. When it happens, all we can do is wait
for the target to try again.
Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION",
... The reselected initiator shall then assert the BSY signal
within a selection abort time of its most recent detection of being
reselected; this is required for correct operation of the time-out
procedure.
The selection abort time is only 200 us which may be insufficient time for a
printk() call. Move the diagnostics to the error paths.
Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When NCR5380_abort() returns FAILED, the driver forgets that the target is
still busy. Hence, further commands may be sent to the target, which may fail
during selection and produce the error message, "reselection after won
arbitration?". Prevent this by leaving the busy flag set when NCR5380_abort()
fails.
Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", that "the
initiator shall not respond to a RESELECTION phase if other than two SCSI ID
bits are on the DATA BUS." This issue (too many bits set) has been observed in
the wild, so add a check.
Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When sense data is valid, call set_driver_byte(cmd, DRIVER_SENSE). Otherwise
some callers of scsi_execute() will ignore sense data. Don't set DID_ERROR or
DID_RESET just because sense data is missing.
Tested-by: Michael Schmitz <schmitzmic@gmail.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When doing a host reset we should be clearing all outstanding commands, not
just the command triggering the reset.
[mkp: adjusted Hannes' SoB address]
Signed-off-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Cc: Ondrey Zary <linux@rainbow-software.org> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the remote is not able to fully utilize the MPS choosen recalculate
the credits based on the actual amount it is sending that way it can
still send packets of MTU size without credits dropping to 0.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We observe an oops in the skx_edac module during boot:
EDAC MC0: Giving out device to module skx_edac controller Skylake Socket#0 IMC#0
EDAC MC1: Giving out device to module skx_edac controller Skylake Socket#0 IMC#1
EDAC MC2: Giving out device to module skx_edac controller Skylake Socket#1 IMC#0
...
EDAC MC13: Giving out device to module skx_edac controller Skylake Socket#0 IMC#1
EDAC MC14: Giving out device to module skx_edac controller Skylake Socket#1 IMC#0
EDAC MC15: Giving out device to module skx_edac controller Skylake Socket#1 IMC#1
Too many memory controllers: 16
EDAC MC: Removed device 0 for skx_edac Skylake Socket#0 IMC#0
We observe there are two memory controllers per socket, with a limit
of 16. Raise the maximum number of memory controllers from 16 to 2 *
MAX_NUMNODES (1024).
[ bp: This is just a band-aid fix until we've sorted out the whole issue
with the bus_type association and handling in EDAC and can get rid of
this arbitrary limit. ]
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we went into sas_rediscover_dev() the attached_sas_addr was already insured
not to be zero. So it's unnecessary to check if the attached_sas_addr is zero.
And although if the sas address is not changed, we always have to unregister
the old device when we are going to register a new one. We cannot just leave
the device there and bring up the new.
Signed-off-by: Jason Yan <yanaijie@huawei.com> CC: chenxiang <chenxiang66@hisilicon.com> CC: John Garry <john.garry@huawei.com> CC: Johannes Thumshirn <jthumshirn@suse.de> CC: Ewan Milne <emilne@redhat.com> CC: Christoph Hellwig <hch@lst.de> CC: Tomas Henzl <thenzl@redhat.com> CC: Dan Williams <dan.j.williams@intel.com> CC: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log