The reboot quirk for ASUS EeeBook X205TA contains a typo in
DMI_PRODUCT_NAME, improperly referring to X205TAW instead of
X205TA, which prevents the quirk from being triggered. The
model X205TAW already has a reboot quirk of its own.
This fix simply removes the inappropriate final letter W.
This USB-SATA bridge chip is used in a StarTech enclosure for
optical drives.
Without the quirk MakeMKV fails during the key exchange with an
installed BluRay drive:
> Error 'Scsi error - ILLEGAL REQUEST:COPY PROTECTION KEY EXCHANGE FAILURE - KEY NOT ESTABLISHED'
> occurred while issuing SCSI command AD010..080002400 to device 'SG:dev_11:2'
So when asus-wmi uses ASUS_WMI_DEVID_WLAN_LED (0x00010002) to store the
wlan state, it drives the airplane-mode indicator LED (through the call
to OWGD) in an inverted fashion: the LED is ON when airplane mode is OFF
(since wlan is ON), and vice-versa.
This commit skips registering RFKill switches at all for these laptops,
to allow the asus-wireless driver to drive the airplane mode LED
correctly through the ASHS ACPI device. Relying on the presence of ASHS
and ASUS_WMI_DSTS_USER_BIT avoids adding DMI-based quirks for at least
21 different laptops.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By referencing Intel Platform Controller Hub(PCH) datasheet,
the xHC USB 2.0 Port Routing(XUSB2PR) at offset 0xD0-0xD3h
decides the setting of mapping the port to EHCI controller or
xHC controller. And the port mapped to xHC will enable xHCI
during bus resume.
The setting of disabling bluetooth adapter's connected port is
0x000001D9. The value can be obtained by few times 1 bit flip
operation. The suited configuration should have the 'lsusb -t'
result with bluetooth using ehci:
/: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/4p, 5000M
/: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/9p, 480M
|__ Port 5: Dev 2, If 0, Class=Video, Driver=uvcvideo, 480M
|__ Port 5: Dev 2, If 1, Class=Video, Driver=uvcvideo, 480M
/: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/2p, 480M
|__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/8p, 480M
|__ Port 6: Dev 3, If 0, Class=Wireless, Driver=btusb, 12M
|__ Port 6: Dev 3, If 1, Class=Wireless, Driver=btusb, 12M
Signed-off-by: Kai-Chuan Hsieh <kai.chiuan@gmail.com> Acked-by: Corentin Chary <corentin.chary@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
[andy: resolve merge conflict in asus-wmi.h] Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. However the interrupt itself was not cleared thus on
first hit, the system enters infinite interrupt handling loop.
On Odroid U3 (Exynos4412), when booted with s3c2410_wdt.soft_noboot=1
argument the console is flooded:
# killall -9 watchdog
[ 60.523760] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
[ 60.536744] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
Fix this by writing something to the WTCLRINT register to clear the
interrupt. The register WTCLRINT however appeared in S3C6410 so a new
watchdog quirk and flavor are needed.
The Qualcomm QDF2xxx root ports don't advertise an ACS capability, but they
do provide ACS-like features to disable peer transactions and validate bus
numbers in requests.
To be specific:
* Hardware supports source validation but it will report the issue as
Completer Abort instead of ACS Violation.
* Hardware doesn't support peer-to-peer and each root port is a root
complex with unique segment numbers.
* It is not possible for one root port to pass traffic to the other root
port. All PCIe transactions are terminated inside the root port.
Add an ACS quirk for the QDF2400 and QDF2432 products.
[bhelgaas: changelog] Signed-off-by: Sinan Kaya <okaya@codeaurora.org> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially all QorIQ platforms were PowerPC architecture and they didn't
support card detection except several platforms. The driver added the
quirk SDHCI_QUIRK_BROKEN_CARD_DETECTION as default and this made broken-cd
property in dts node didn't work. Now QorIQ platform turns to ARM
architecture and most of them could support card detection. However it's
a large number of dts trees that need to be fixed with broken-cd if we
remove the default SDHCI_QUIRK_BROKEN_CARD_DETECTION in driver. And the
users don't want to see this. So this patch is to remove this default
quirk just for ARM and keep it for PowerPC.(Note, QorIQ PowerPC platform
only has big-endian eSDHC while QorIQ ARM platform has big-endian or
little-endian eSDHC) This makes broken-cd property work again for ARM.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCIe Root Port in Hip06/Hip07 SoCs advertises an MSI capability, but it
cannot generate MSIs. It can transfer MSI/MSI-X from downstream devices,
but does not support MSI/MSI-X itself.
Add a quirk to prevent use of MSI/MSI-X by the Root Port.
[bhelgaas: changelog, sort vendor ID #define, drop device ID #define] Signed-off-by: Dongdong Liu <liudongdong3@huawei.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: Gabriele Paoloni <gabriele.paoloni@huawei.com> Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Broadcom Northstar2 SoC has a number of quirks for the PAXC
(internal/fake) PCI bus. Specifically, the PCI config space is shared
between the root port and the first PF (ie., PF0), and a number of fields
are tied to zero (thus preventing them from being set). These cannot be
"fixed" in device firmware, so we must fix them with a quirk.
Commit 680a0873e193 ("arm: kernel: Add SMC structure parameter") added
a new "quirk" parameter to the SMC and HVC SMCCC backends, but only
updated the comment for the SMC version. This patch adds the new
paramater to the comment describing the HVC version too.
We get 2 warnings when building kernel with W=1:
drivers/gpu/drm/msm/adreno/a3xx_gpu.c:535:17: warning: no previous prototype for 'a3xx_gpu_init' [-Wmissing-prototypes]
drivers/gpu/drm/msm/adreno/a4xx_gpu.c:624:17: warning: no previous prototype for 'a4xx_gpu_init' [-Wmissing-prototypes]
In fact, both functions are declared in
drivers/gpu/drm/msm/adreno/adreno_device.c, but should be declared
in a header file. So this patch moves both function declarations to
drivers/gpu/drm/msm/adreno/adreno_gpu.h.
This patch adds a Qualcomm specific quirk to the arm_smccc_smc call.
On Qualcomm ARM64 platforms, the SMC call can return before it has
completed. If this occurs, the call can be restarted, but it requires
using the returned session ID value from the interrupted SMC call.
The quirk stores off the session ID from the interrupted call in the
quirk structure so that it can be used by the caller.
This patch folds in a fix given by Sricharan R:
https://lkml.org/lkml/2016/9/28/272
Signed-off-by: Andy Gross <andy.gross@linaro.org> Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a quirk parameter to the arm_smccc_(smc/hvc) calls.
The quirk structure allows for specialized SMC operations due to SoC
specific requirements. The current arm_smccc_(smc/hvc) is renamed and
macros are used instead to specify the standard arm_smccc_(smc/hvc) or
the arm_smccc_(smc/hvc)_quirk function.
This patch and partial implementation was suggested by Will Deacon.
Signed-off-by: Andy Gross <andy.gross@linaro.org> Reviewed-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Non-generic devices have numbered_buttons set for both pen and
touch interfaces by default. The actual number of buttons on the
interface is normally manually decided later, which is different
from what those HID generic devices are processed, where number
of buttons are directly retrieved from HID descriptors.
This patch adds the missed HID_GENERIC check and moves the statement
to wacom_setup_pad_input_capabilities since it's not a quirk anymore.
Some SoCs have a reset line that must be asserted/deasserted.
This patch adds a quirk to handle the new compatible
"allwinner,sun6i-a31-i2s" which will deassert the reset
line on probe function and assert it on remove's one.
This new compatible is useful in case of A33 codec driver, for example.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 821d6f0359b0 (ACPI / sleep: Do not save NVS for new machines to
accelerate S3), to optimize S3 suspend/resume speed, code is introduced
to ignore NVS memory saving during S3 for all the platforms later than
2012.
But, Lenovo G50-45, a platform released in 2015, still needs NVS memory
saving during S3. A quirk is introduced for this platform.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=189431 Tested-by: Przemek <soprwa@gmail.com> Signed-off-by: Zhang Rui <rui.zhang@intel.com>
[ rjw: Drop unnecessary code ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix classic issue of having multiple codecs listed in DSDT
but a single one actually enabled. The previous code did
not handle such errors and could also lead to uninitalized
configurations
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
More and more platforms need the button.lid_init_state=open quirk. This
patch sets it the default behavior.
If a platform doesn't send lid open event or lid open event is lost due to
the underlying system problems, then we can compare various combinations:
1. systemd/acpid is used to suspend system or not, systemd has a special
logic forcing open event after resuming;
2. _LID returns a cached value or not.
The result is as follows:
1. lid_init_state=method
1. cached
1. resumed by lid:
(x) event=close
(x) systemd=suspends again
(x) acpid=suspends again
(x) state=close
2. resumed by other:
(o) event=close
(x) systemd=suspends again
(x) acpid=suspends again
(o) state=close
2. non-cached
1. resumed by lid:
(o) event=open
(o) systemd=resumes
(o) acpid=resumes
(o) state=open
2. resumed by other:
(o) event=close
(x) systemd=suspends again
(x) acpid=suspends again
(o) state=close
2. lid_init_state=open
1. cached
1. resumed by lid:
(o) event=open
(o) systemd=resumes
(o) acpid=resumes
(x) state=close
2. resumed by other:
(x) event=open
(o) systemd=resumes
(o) acpid=resumes
(o) state=close
2. non-cached
1. resumed by lid:
(o) event=open
(o) systemd=resumes
(o) acpid=resumes
(o) state=open
2. resumed by other:
(x) event=open
(o) systemd=resumes
(o) acpid=resumes
(o) state=close
3. lid_init_state=ignore
1. cached
1. resumed by lid:
(o) event=none
(x) systemd=suspends again
(o) acpid=resumes
(x) state=close
2. resumed by other:
(o) event=none
(x) systemd=suspends again
(o) acpid=resumes
(o) state=close
2. non-cached
1. resumed by lid:
(o) event=none
(x) systemd=suspends again
(o) acpid=resumes
(o) state=open
2. resumed by other:
(o) event=none
(x) systemd=suspends again
(o) acpid=resumes
(o) state=close
As a conclusion:
1. With systemd changed, lid_init_state=ignore has only one problem and the
problem comes from an underlying issue, not userspace and kernel lid
handling.
2. Without systemd changed, lid_init_state=open can be the default
behavior as the pass ratio is not much worse than lid_init_state=ignore.
3. lid_init_state=method is buggy, we can have a separate patch to make it
deprectated.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=187271 Signed-off-by: Lv Zheng <lv.zheng@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's an issue with the da850 SATA controller: if port multiplier
support is compiled in, but we're connecting the drive directly to
the SATA port on the board, the drive can't be detected.
To make SATA work on the da850-lcdk board: first try to softreset
with pmp - if the operation fails with -EBUSY, retry without pmp.
Intel 200-series chipsets have the same errata as 100-series: the ACS
capability doesn't follow the PCIe spec, the capability and control
registers are dwords rather than words. Add PCIe root port device IDs to
existing quirk.
Since v4.10-rc1, the following logs appears in loop :
[ 801.953836] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 801.960455] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 801.966611] usb usb6-port1: cannot disable (err = -32)
[ 806.083772] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 806.090370] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 806.096494] usb usb6-port1: cannot disable (err = -32)
After analysis, xhci try to set link in U3 and returns an error.
Using snps,dis_u3_susphy_quirk fix this issue.
dwc3 revisions <=3.00a have a limitation where Port Disable command
doesn't work. Set the quirk-broken-port-ped property for such
controllers so XHCI core can do the necessary workaround.
[rogerq@ti.com] Updated code from platform data to device property.
Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices from Texas Instruments [1] suffer from
a silicon bug where Port Enabled/Disabled bit
should not be used to silence an erroneous device.
The bug is so that if port is disabled with PED
bit, an IRQ for device removal (or attachment)
will never fire.
Just for the sake of completeness, the actual
problem lies with SNPS USB IP and this affects
all known versions up to 3.00a. A separate
patch will be added to dwc3 to enabled this
quirk flag if version is <= 3.00a.
[1] - AM572x Silicon Errata http://www.ti.com/lit/er/sprz429j/sprz429j.pdf
Section i896— USB xHCI Port Disable Feature Does Not Work
GPIO descriptors are the preferred way over legacy GPIO numbers
nowadays. Convert the driver to use GPIO descriptors internally but
still allow passing legacy GPIO numbers from platform data to support
existing platforms.
Based on commits 633a21d80b4a2cd6 ("input: gpio_keys_polled: Add support
for GPIO descriptors") and 1ae5ddb6f8837558 ("Input: gpio_keys_polled -
request GPIO pin as input.").
UART uses as EDMA as dma engine on AM437x SoC and therefore, requires
OMAP_DMA_TX_KICK quirk just like AM33xx. So, enable OMAP_DMA_TX_KICK
quirk for AM437x platform as well. While at that, drop use of
of_machine_is_compatible() and instead pass quirks via device data.
Signed-off-by: Vignesh R <vigneshr@ti.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core framework already handles setting this parameter with a
platform quirk. Add the appropriate flag so that we always set
AHBBURST to 0. Technically DT should be doing this, but we always
do it for msm chipidea devices so setting the flag in the driver
works just as well. If the burst needs to be anything besides 0,
we expect the 'ahb-burst-config' dts property to be present.
Acked-by: Peter Chen <peter.chen@nxp.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> Signed-off-by: Peter Chen <peter.chen@nxp.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we issue the link startup to the device while its UniPro state is
LinkDown (and device state is sleep/power-down) then link startup
will not move the device state to Active. Device will only move to
active state if the link starup is issued when its UniPro state is
LinkUp. So in this case, we would have to issue the link startup 2
times to make sure that device moves to active state.
There are literally dozens of Insyde devices with a different
name but with the same audio routing. Use a generic quirk to
match on vendor name only to avoid recurring edits of the
same thing.
Signed-off-by: youling257 <youling257@gmail.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in 2014, commit fb7023e0e248 ("drm/i915: BDW: Adding Reserved PCI
IDs.") added the reserved PCI IDs in order to try to make sure we had
working drivers in case we ever released products using these IDs
(since we had instances of this type of problem in the past). The
problem is that the patch only touched the macros used by
early-quirks.c and by the user space components that rely on
i915_pciids.h, it didn't touch the macros used by i915_pci.c. So we
correctly handled the stolen memory for these theoretical IDs, but we
didn't actually drive the devices from i915.ko.
So this patch fixes the original commit by actually making i915.ko
drive these IDs, which was the goal. There's no information on what
would be the GT count on these IDs, so we just go with the safer
intel_broadwell_info, at the risk of ignoring a possibly inexistent
BSD2_RING.
I did some checking, and it seems that these IDs are driven by
intel-gpu-tools, xf86-video-intel and libdrm (since they contain old
copies of i915_pciids.h), but they are not checked by mesa.
The alternative to this patch would be to just assume we're actually
never going to use these IDs, and then remove them from our ID lists
and make sure our user space components sync the latest i915_pciids.h
copy. I'm fine with either approaches, as long as we make sure that
every component tries to drive the same list of PCI IDs.
Commit 8d9c20e1d1e3 ("drm/i915: Remove .is_mobile field from platform
struct") removed mobile vs desktop differences for HSW+, but forgot
the Broadwell reserved IDs, so do it now.
It's interesting to notice that these IDs are used by early-quirks.c
but are *not* used by i915_pci.c.
Cc: Carlos Santa <carlos.santa@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1483473860-17644-2-git-send-email-paulo.r.zanoni@intel.com Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove duplicated IDs from the list. Currently, this definition is
only used by early-quirks.c. From my understanding of the code, having
duplicated IDs shouldn't be causing any bugs.
Fixes: 8d9c20e1d1e3 ("drm/i915: Remove .is_mobile field from platform struct") Cc: Carlos Santa <carlos.santa@intel.com> Cc: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1483473860-17644-1-git-send-email-paulo.r.zanoni@intel.com Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DolphinBar by Mayflash (identified as Dragonrise) needs
HID_QUIRK_MULTI_INPUT to split it up into four input devices. Without this
quirk the adapter is falsely recognized as a tablet. See also bug 115841
(https://bugzilla.kernel.org/show_bug.cgi?id=115841).
Sometimes, the users may require a quirk to be provided from ACPI subsystem
core to prevent a GPE from flooding.
Normally, if a GPE cannot be dispatched, ACPICA core automatically prevents
the GPE from firing. But there are cases the GPE is dispatched by _Lxx/_Exx
provided via AML table, and OSPM is lacking of the knowledge to get
_Lxx/_Exx correctly executed to handle the GPE, thus the GPE flooding may
still occur.
The existing quirk mechanism can be enabled/disabled using the following
commands to prevent such kind of GPE flooding during runtime:
# echo mask > /sys/firmware/acpi/interrupts/gpe00
# echo unmask > /sys/firmware/acpi/interrupts/gpe00
To avoid GPE flooding during boot, we need a boot stage mechanism.
This patch provides such a boot stage quirk mechanism to stop this kind of
GPE flooding. This patch doesn't fix any feature gap but since the new
feature gaps could be found in the future endlessly, and can disappear if
the feature gaps are filled, providing a boot parameter rather than a DMI
table should suffice.
Some OEMs believe they own the Identify Controller vendor specific
region and will repurpose it with their own values. While not common,
we can't rely on the PCI VID:DID to tell use how to decode the field
we reserved for this as the stripe size so we need to do something else
for the list of devices using this quirk.
The field was supposed to allow flexibility on the device's back-end
striping, but it turned out that never materialized; the chunk is always
the same as MDTS in the products subscribing to this quirk, so this
patch removes the stripe_size field and sets the chunk to the max hw
transfer size for the devices using this quirk.
Signed-off-by: Keith Busch <keith.busch@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMW0_GUID1 wmi is not only found on Acer family but also other
machines like Lenovo, Fujitsu and Medion. In the past, acer-wmi handled
those non-Acer machines by quirks list.
But actually acer-wmi driver was loaded on any machine that had
AMW0_GUID1. This behavior is strange because those machines should be
supported by appropriate wmi drivers. e.g. fujitsu-laptop,
ideapad-laptop.
This patch adds the logic to check the machine that has AMW0_GUID1
should be in Acer/Packard Bell/Gateway white list. But, it still keeps
the quirk list of those supported non-acer machines for backward
compatibility.
This patch adds native DSD support for the following devices.
- TEAC NT-503
- TEAC UD-503
- TEAC UD-501
(1) Add quirks for native DSD support for TEAC devices.
(2) A specific vendor command is needed to switch between PCM/DOP and
DSD mode, same as Denon/Marantz devices.
The Axe-Fx II implicit feedback end point and the data sync endpoint
are in different interface descriptors. Add quirk to ensure a sync
endpoint is properly configured.
The maximum value PA_SaveConfigTime is 250 (10us) but this is not enough
for some vendors. Gear switch from PWM to HS may fail even with this
max. PA_SaveConfigTime. Gear switch can be issued by host controller as
an error recovery and any software delay will not help on this case so
we need to increase PA_SaveConfigTime to >32us as per vendor
recommendation. This change adds a quirk to increase the
PA_SaveConfigTime parameter.
Currently we use one shared global acpi_pci_root_ops structure to keep
controller-specific ops. We pass its pointer to acpi_pci_root_create() and
associate it with a host bridge instance for good. Such a design implies
serious drawback. Any potential manipulation on the single system-wide
acpi_pci_root_ops leads to kernel crash. The structure content is not
really changing even across multiple host bridges creation; thus it was not
an issue so far.
In preparation for adding ECAM quirks mechanism (where controller-specific
PCI ops may be different for each host bridge) allocate new
acpi_pci_root_ops and fill in with data for each bridge. Now it is safe to
have different controller-specific info. As a consequence free
acpi_pci_root_ops when host bridge is released.
No functional changes in this patch.
Signed-off-by: Tomasz Nowicki <tn@semihalf.com> Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add CPU ID for Atom Z34xx processors. Datasheets indicate support for this,
detailed information about potential quirks or limitations are missing, though.
So we just reuse the definition from official BSP code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Len Brown <len.brown@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
S5.3.3.1 of RFC 2203 requires that an incoming GSS-wrapped message
whose sequence number lies outside the current window is dropped.
The rationale is:
The reason for discarding requests silently is that the server
is unable to determine if the duplicate or out of range request
was due to a sequencing problem in the client, network, or the
operating system, or due to some quirk in routing, or a replay
attack by an intruder. Discarding the request allows the client
to recover after timing out, if indeed the duplication was
unintentional or well intended.
However, clients may rely on the server dropping the connection to
indicate that a retransmit is needed. Without a connection reset, a
client can wait forever without retransmitting, and the workload
just stops dead. I've reproduced this behavior by running xfstests
generic/323 on an NFSv4.0 mount with proto=rdma and sec=krb5i.
To address this issue, have the server close the connection when it
silently discards an incoming message due to a GSS sequence number
problem.
There are a few other places where the server will never reply.
Change those spots in a similar fashion.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UFS devices require host PA_TACTIVATE to be higher than
device PA_TACTIVATE otherwise it may get stuck during hibern8 sequence.
This change allows this by using quirk.
We already have in place a quirk for Windows 8 devices, but it looks
like the Surface Cover are not conforming to it.
Given that we are only interested in 3 feature reports (the ones that
the Windows driver retrieves), we should be safe to unconditionally apply
the quirk to everybody.
In case there is an issue with a controller, we can always mark it as such
in the transport driver, and hid-multitouch won't try to retrieve the
feature report.
There is no reasons to filter out keyboard and consumer control collections
in hid-multitouch.
With the previous hid-input fix, there is now a full support of the Type
Cover and we can remove all specific bits from hid-core and hid-microsoft.
hid-multitouch will automatically set HID_QUIRK_NO_INIT_REPORTS so we can
also remove it from the list of ushbid quirks.
The ARM specifies that the system counter "must be implemented in an
always-on power domain," and so we try to use the counter as a source of
timekeeping across suspend/resume. Unfortunately, some SoCs (e.g.,
Rockchip's RK3399) do not keep the counter ticking properly when
switched from their high-power clock to the lower-power clock used in
system suspend. Support this quirk by adding a new device tree property.
Signed-off-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We added a bunch of new Mellanox device ID definitions because they'll be
used by INTx quirks. Use them in the mlx4 ID table also so grep can find
both places. No functional change intended.
Most Baytrail-CR devices use analog differential microphones,
modify capture default to avoid DMI quirks. Keep digital mics
for all other configurations.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Certain devices produced by Weida Tech need to have a wakeup command sent to
them before powering on. The call itself will come back with error, but the
device can be powered on afterwards.
All known gamepad adapters by Mayflash (identified as Dragonrise) need
HID_QUIRK_MULTI_INPUT to split them up into four input devices. Without this
quirk those adapters are falsely recognized as tablets. Fixes bug 115841
(https://bugzilla.kernel.org/show_bug.cgi?id=115841).
In common clock framework CLK_DIVIDER_ONE_BASED or'ed with
CLK_DIVIDER_ALLOW_ZERO flags indicates that
1) a divider clock may be set to zero value,
2) divider's zero value is interpreted as a non-divided clock.
On the LPC32xx platform clock dividers of PWM and memory card clocks
comply with the first condition, but zero value means a gated clock,
thus it may happen that the divider value is not updated when
the clock is enabled and the clock remains gated.
The change adds one-shot quirks, which check for zero value of divider
on initialization and set it to a non-zero value, therefore in runtime
a gate clock will work as expected.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Reviewed-by: Sylvain Lemieux <slemieux.tyco@gmail.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The A31's display pipeline has 2 frontends, 2 backends, and 2 TCONs. It
also has new display enhancement blocks, such as the DRC (Dynamic Range
Controller), the DEU (Display Enhancement Unit), and the CMU (Color
Management Unit). It supports HDMI, MIPI DSI, and 2 LCD/LVDS channels.
The A31s display pipeline is almost the same, just without MIPI DSI.
Only the TCON seems to be different, due to the missing mux for MIPI
DSI.
Add compatible strings for both of them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org> Acked-by: Rob Herring <robh@kernel.org> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We already have some differences between the 2 supported SoCs.
More will be added as we support other SoCs. To avoid bloating
the probe function with even more conditionals, move the quirks
to a separate data structure that's tied to the compatible string.
Now that our crng uses chacha20, we can rely on its speedy
characteristics for replacing MD5, while simultaneously achieving a
higher security guarantee. Before the idea was to use these functions if
you wanted random integers that aren't stupidly insecure but aren't
necessarily secure either, a vague gray zone, that hopefully was "good
enough" for its users. With chacha20, we can strengthen this claim,
since either we're using an rdrand-like instruction, or we're using the
same crng as /dev/urandom. And it's faster than what was before.
We could have chosen to replace this with a SipHash-derived function,
which might be slightly faster, but at the cost of having yet another
RNG construction in the kernel. By moving to chacha20, we have a single
RNG to analyze and verify, and we also already get good performance
improvements on all platforms.
Implementation-wise, rather than use a generic buffer for both
get_random_int/long and memcpy based on the size needs, we use a
specific buffer for 32-bit reads and for 64-bit reads. This way, we're
guaranteed to always have aligned accesses on all platforms. While
slightly more verbose in C, the assembly this generates is a lot
simpler than otherwise.
Finally, on 32-bit platforms where longs and ints are the same size,
we simply alias get_random_int to get_random_long.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Suggested-by: Theodore Ts'o <tytso@mit.edu> Cc: Theodore Ts'o <tytso@mit.edu> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: Andy Lutomirski <luto@amacapital.net> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the case that compat_get_bitmap fails we do not want to copy the
bitmap to the user as it will contain uninitialized stack data and leak
sensitive data.
A patch documenting how to specify which kernels a particular fix should
be backported to (seemingly) inadvertently added a minus sign after the
kernel version. This particular stable-tag format had never been used
prior to this patch, and was neither present when the patch in question
was first submitted (it was added in v2 without any comment).
Drop the minus sign to avoid any confusion.
Fixes: fdc81b7910ad ("stable_kernel_rules: Add clause about specification of kernel versions to patch.") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If scache.waysize is 0, r4k___flush_cache_all() will do nothing and
then cause bugs. BTW, though vcache.waysize isn't being used by now,
we also fix its calculation.
On VTLB+FTLB platforms (such as Loongson-3A R2), FTLB's pagesize is
usually configured the same as PAGE_SIZE. In such a case, Huge page
entry is not suitable to write in FTLB.
Unfortunately, when a huge page is created, its page table entries
haven't created immediately. Then the TLB refill handler will fetch an
invalid page table entry which has no "HUGE" bit, and this entry may be
written to FTLB. Since it is invalid, TLB load/store handler will then
use tlbwi to write the valid entry at the same place. However, the
valid entry is a huge page entry which isn't suitable for FTLB.
Our solution is to modify build_huge_handler_tail. Flush the invalid
old entry (whether it is in FTLB or VTLB, this is in order to reduce
branches) and use tlbwr to write the valid new entry.
Loongson-3's micro TLB (ITLB) is not strictly a subset of JTLB. That
means: when a JTLB entry is replaced by hardware, there may be an old
valid entry exists in ITLB. So, a TLB miss exception may occur while
handle_ri_rdhwr() is running because it try to access EPC's content.
However, handle_ri_rdhwr() doesn't clear EXL, which makes a TLB Refill
exception be treated as a TLB Invalid exception and tlbp may fail. In
this case, if FTLB (which is usually set-associative instead of set-
associative) is enabled, a tlbp failure will cause an invalid tlbwi,
which will hang the whole system.
This patch rename handle_ri_rdhwr_vivt to handle_ri_rdhwr_tlbp and use
it for Loongson-3. It try to solve the same problem described as below,
but more straightforwards.
https://patchwork.linux-mips.org/patch/12591/
I think Loongson-2 has the same problem, but it has no FTLB, so we just
keep it as is.
Commit 08b3c894e565 ("MIPS: lantiq: Disable xbar fpi burst mode")
accidentally requested the resources from the pmu address region
instead of the xbar registers region, but the check for the return
value of request_mem_region() was wrong. Commit 98ea51cb0c8c ("MIPS:
Lantiq: Fix another request_mem_region() return code check") fixed the
check of the return value of request_mem_region() which made the kernel
panics.
This patch now makes use of the correct memory region for the cross bar.
When building for microMIPS we need to ensure that the assembler always
knows that there is code at the target of a branch or jump. Recent
toolchains will fail to link a microMIPS kernel when this isn't the case
due to what it thinks is a branch to non-microMIPS code.
mips-mti-linux-gnu-ld kernel/built-in.o: .spinlock.text+0x2fc: Unsupported branch between ISA modes.
mips-mti-linux-gnu-ld final link failed: Bad value
This is due to inline assembly labels in spinlock.h not being followed
by an instruction mnemonic, either due to a .subsection pseudo-op or the
end of the inline asm block.
Fix this with a .insn direction after such labels.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Maciej W. Rozycki <macro@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/15325/ Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a 32-bit kernel is configured to support MIPS64r6 (CPU_MIPS64_R6),
MIPS_O32_FP64_SUPPORT won't be selected as it should be because
MIPS32_O32 is disabled (o32 is already the default ABI available on
32-bit kernels).
This results in userland FP breakage as CP0_Status.FR is read-only 1
since r6 (when an FPU is present) so __enable_fpu() will fail to clear
FR. This causes the FPU emulator to get used which will incorrectly
emulate 32-bit FPU registers.
Force o32 fp64 support in this case by also selecting
MIPS_O32_FP64_SUPPORT from CPU_MIPS64_R6 if 32BIT.
Fixes: 4e9d324d4288 ("MIPS: Require O32 FP64 support for MIPS64 with O32 compat") Signed-off-by: James Hogan <james.hogan@imgtec.com> Reviewed-by: Paul Burton <paul.burton@imgtec.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15310/ Signed-off-by: James Hogan <james.hogan@imgtec.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit fd2d2b191fe7 ("s390: get_user() should zero on failure")
intended to fix s390's get_user() implementation which did not zero
the target operand if the read from user space faulted. Unfortunately
the patch has no effect: the corresponding inline assembly specifies
that the operand is only written to ("=") and the previous value is
discarded.
Therefore the compiler is free to and actually does omit the zero
initialization.
To fix this simply change the contraint modifier to "+", so the
compiler cannot omit the initialization anymore.
Fixes: c9ca78415ac1 ("s390/uaccess: provide inline variants of get_user/put_user") Fixes: fd2d2b191fe7 ("s390: get_user() should zero on failure") Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reorder the operations in decompress_kernel() to ensure initrd is moved
to a safe location before the bss section is zeroed.
During decompression bss can overlap with the initrd and this can
corrupt the initrd contents depending on the size of the compressed
kernel (which affects where the initrd is placed by the bootloader) and
the size of the bss section of the decompressor.
Also use the correct initrd size when checking for overlaps with
parmblock.
When __pa is applied to virtual address in uncached KSEG region the
result is incorrect. Fix it by checking if the original address is in
the uncached KSEG and adjusting the result. It looks better than masking
off bits because pfn_valid would correctly work with new __pa results
and it may be made working in noMMU case, once we get definition for
uncached memory view.
This is required for the dma_common_mmap and DMA debug code to work
correctly: they both indirectly use __pa with coherent DMA addresses.
In case of DMA debug the visible effect is false reports that an address
mapped for DMA is accessed by CPU.
Tested-by: Boris Brezillon <boris.brezillon@free-electrons.com> Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to reserve the boot memory for the flattened device tree.
Otherwise it might get overwritten, e.g. when initial_boot_params is
copied, leading to a corrupted FDT and a boot hang/crash:
bootconsole [early0] enabled
Early console on uart16650 initialized at 0xf8001600
OF: fdt: Error -11 processing FDT
Kernel panic - not syncing: setup_cpuinfo: No CPU found in devicetree!
---[ end Kernel panic - not syncing: setup_cpuinfo: No CPU found in devicetree!
Guenter Roeck says:
> I think I found the problem. In unflatten_and_copy_device_tree(), with added
> debug information:
>
> OF: fdt: initial_boot_params=c861e400, dt=c861f000 size=28874 (0x70ca)
>
> ... and then initial_boot_params is copied to dt, which results in corrupted
> fdt since the memory overlaps. Looks like the initial_boot_params memory
> is not reserved and (re-)allocated by early_init_dt_alloc_memory_arch().
Commit 4257e08 ("dm raid: support to change bitmap region size")
introduced a bitmap resize call during preresume phase. User can create
a DM device with "raid" target configured as raid1 with no metadata
devices to hold superblock/bitmap info. It can be achieved using the
following sequence:
The raid_preresume() function incorrectly assumes that the raid_set has
a bitmap enabled if RT_FLAG_RS_BITMAP_LOADED is set. But
RT_FLAG_RS_BITMAP_LOADED is getting set in __load_dirty_region_bitmap()
even if there is no bitmap present (and bitmap_load() happily returns 0
even if a bitmap isn't present). So the only way forward in the
near-term is to check if the bitmap is present by seeing if
mddev->bitmap is not NULL after bitmap_load() has been called.
By doing so the above NULL pointer is avoided.
Fixes: 4257e08 ("dm raid: support to change bitmap region size") Signed-off-by: Dmitry Bilunov <kmeaw@yandex-team.ru> Signed-off-by: Andrey Smetanin <asmetanin@yandex-team.ru> Acked-by: Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It used to be sufficient just to call pagefault_disable(), because that
also disabled preemption. But the two were decoupled in commit 8222dbe21e79
("sched/preempt, mm/fault: Decouple preemption from the page fault
logic") in mid 2015.
So add the missing preempt_disable/enable(). We should also call
disable_kernel_fp(), although it does nothing by default, there is a
debug switch to make it active and all enables should be paired with
disables.
In the past, there was only one load-with-reservation instruction,
lwarx, and if a program attempted a lwarx on a misaligned address, it
would take an alignment interrupt and the kernel handler would emulate
it as though it was lwzx, which was not really correct, but benign since
it is loading the right amount of data, and the lwarx should be paired
with a stwcx. to the same address, which would also cause an alignment
interrupt which would result in a SIGBUS being delivered to the process.
We now have 5 different sizes of load-with-reservation instruction. Of
those, lharx and ldarx cause an immediate SIGBUS by luck since their
entries in aligninfo[] overlap instructions which were not fixed up, but
lqarx overlaps with lhz and will be emulated as such. lbarx can never
generate an alignment interrupt since it only operates on 1 byte.
To straighten this out and fix the lqarx case, this adds code to detect
the l[hwdq]arx instructions and return without fixing them up, resulting
in a SIGBUS being delivered to the process.
Signed-off-by: Paul Mackerras <paulus@ozlabs.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the kernel is compiled to use 64bit ABIv2 the _GLOBAL() macro does
not include a global entry point. A function's global entry point is
used when the function is called from a different TOC context and in the
kernel this typically means a call from a module into the vmlinux (or
vice-versa).
There are a few exported asm functions declared with _GLOBAL() and
calling them from a module will likely crash the kernel since any TOC
relative load will yield garbage.
flush_icache_range() and flush_dcache_range() are both exported to
modules, and use the TOC, so must use _GLOBAL_TOC().
Fixes: 721aeaa9fdf3 ("powerpc: Build little endian ppc64 kernel with ABIv2") Signed-off-by: Oliver O'Halloran <oohall@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4c6d9acce1f4 ("powerpc/mm: Add hooks for cxl") converted local
TLB invalidates to global if the cxl driver is active. This is necessary
because the CAPP snoops invalidations to forward them to the PSL on the
cxl adapter. However one path was forgotten. native_flush_hash_range()
still does local TLB invalidates, as found out the hard way recently.
This patch fixes it by following the same logic as previously: if the
cxl driver is active, the local TLB invalidates are 'upgraded' to
global.
On Power8 & Power9 the early CPU inititialisation in __init_HFSCR()
turns on HFSCR[TM] (Hypervisor Facility Status and Control Register
[Transactional Memory]), but that doesn't take into account that TM
might be disabled by CPU features, or disabled by the kernel being built
with CONFIG_PPC_TRANSACTIONAL_MEM=n.
So later in boot, when we have setup the CPU features, clear HSCR[TM] if
the TM CPU feature has been disabled. We use CPU_FTR_TM_COMP to account
for the CONFIG_PPC_TRANSACTIONAL_MEM=n case.
Without this a KVM guest might try use TM, even if told not to, and
cause an oops in the host kernel. Typically the oops is seen in
__kvmppc_vcore_entry() and may or may not be fatal to the host, but is
always bad news.
In practice all shipping CPU revisions do support TM, and all host
kernels we are aware of build with TM support enabled, so no one should
actually be able to hit this in the wild.
Fixes: 2a3563b023e5 ("powerpc: Setup in HFSCR for POWER8") Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
[mpe: Rewrite change log with input from Sam, add Fixes/stable] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rapf copy loops in the Meta usercopy code is missing some extable
entries for HTP cores with unaligned access checking enabled, where
faults occur on the instruction immediately after the faulting access.
Add the fixup labels and extable entries for these cases so that corner
case user copy failures don't cause kernel crashes.
The fixup code to rewind the source pointer in
__asm_copy_from_user_{32,64}bit_rapf_loop() always rewound the source by
a single unit (4 or 8 bytes), however this is insufficient if the fault
didn't occur on the first load in the loop, as the source pointer will
have been incremented but nothing will have been stored until all 4
register [pairs] are loaded.
Read the LSM_STEP field of TXSTATUS (which is already loaded into a
register), a bit like the copy_to_user versions, to determine how many
iterations of MGET[DL] have taken place, all of which need rewinding.
The fixup code for the copy_to_user rapf loops reads TXStatus.LSM_STEP
to decide how far to rewind the source pointer. There is a special case
for the last execution of an MGETL/MGETD, since it leaves LSM_STEP=0
even though the number of MGETLs/MGETDs attempted was 4. This uses ADDZ
which is conditional upon the Z condition flag, but the AND instruction
which masked the TXStatus.LSM_STEP field didn't set the condition flags
based on the result.
Fix that now by using ANDS which does set the flags, and also marking
the condition codes as clobbered by the inline assembly.
projects / linux-stable / log