Commit 761ed4a94582 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e46e ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145ace ("tty/serial: do not free
trasnmit buffer page under port lock")).
The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000
Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.
Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.
The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.
This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:
* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received
This repeats then for each group of 4 input values.
This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.
RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.
caused by `c->vc_cell_height' not having been initialized. This has
only started to trigger with commit 860dafa90259 ("vt: Fix character
height handling with VT_RESIZEX"), however the ultimate offender is
commit 50ec42edd978 ("[PATCH] Detaching fbcon: fix vgacon to allow
retaking of the console").
Said commit has added a call to `vc_resize' whenever `vgacon_init' is
called with the `init' argument set to 0, which did not happen before.
And the call is made before a key vgacon boot parameter retrieved in
`vgacon_startup' has been propagated in `vgacon_init' for `vc_resize' to
use to the console structure being worked on. Previously the parameter
was `c->vc_font.height' and now it is `c->vc_cell_height'.
In this particular scenario the registration of fbcon has failed and vt
resorts to vgacon. Now fbcon does have initialized `c->vc_font.height'
somehow, unlike `c->vc_cell_height', which is why this code did not
crash before, but either way the boot parameters should have been copied
to the console structure ahead of the call to `vc_resize' rather than
afterwards, so that first the call has a chance to use them and second
they do not change the console structure to something possibly different
from what was used by `vc_resize'.
Move the propagation of the vgacon boot parameters ahead of the call to
`vc_resize' then. Adjust the comment accordingly.
Fixes: 50ec42edd978 ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console") Cc: stable@vger.kernel.org # v2.6.18+ Reported-by: Wim Osterholt <wim@djo.tudelft.nl> Reported-by: Pavel V. Panteleev <panteleev_p@mcst.ru> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2110252317110.58149@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On newer debian releases the debian-provided "installkernel" script is
installed in /usr/sbin. Fix the kernel install.sh script to look for the
script in this directory as well.
Correct an error where setting /proc/sys/net/rds/tcp/rds_tcp_rcvbuf would
instead modify the socket's sk_sndbuf and would leave sk_rcvbuf untouched.
Fixes: c6a58ffed536 ("RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket") Signed-off-by: William Kucharski <william.kucharski@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ARM v6 and later, we define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
because the ordinary load/store instructions (ldr, ldrh, ldrb) can
tolerate any misalignment of the memory address. However, load/store
double and load/store multiple instructions (ldrd, ldm) may still only
be used on memory addresses that are 32-bit aligned, and so we have to
use the CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS macro with care, or we
may end up with a severe performance hit due to alignment traps that
require fixups by the kernel. Testing shows that this currently happens
with clang-13 but not gcc-11. In theory, any compiler version can
produce this bug or other problems, as we are dealing with undefined
behavior in C99 even on architectures that support this in hardware,
see also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363.
Fortunately, the get_unaligned() accessors do the right thing: when
building for ARMv6 or later, the compiler will emit unaligned accesses
using the ordinary load/store instructions (but avoid the ones that
require 32-bit alignment). When building for older ARM, those accessors
will emit the appropriate sequence of ldrb/mov/orr instructions. And on
architectures that can truly tolerate any kind of misalignment, the
get_unaligned() accessors resolve to the leXX_to_cpup accessors that
operate on aligned addresses.
Since the compiler will in fact emit ldrd or ldm instructions when
building this code for ARM v6 or later, the solution is to use the
unaligned accessors unconditionally on architectures where this is
known to be fast. The _aligned version of the hash function is
however still needed to get the best performance on architectures
that cannot do any unaligned access in hardware.
This new version avoids the undefined behavior and should produce
the fastest hash on all architectures we support.
In qlcnic_83xx_add_rings(), the indirect function of
ahw->hw_ops->alloc_mbx_args will be called to allocate memory for
cmd.req.arg, and there is a dereference of it in qlcnic_83xx_add_rings(),
which could lead to a NULL pointer dereference on failure of the
indirect function like qlcnic_83xx_alloc_mbx_args().
Fix this bug by adding a check of alloc_mbx_args(), this patch
imitates the logic of mbx_cmd()'s failure handling.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_QLCNIC=m show no new warnings, and our
static analyzer no longer warns about this code.
Fix section mismatch warnings in xtsonic. The first one appears to be
bogus and after fixing the second one, the first one is gone.
WARNING: modpost: vmlinux.o(.text+0x529adc): Section mismatch in reference from the function sonic_get_stats() to the function .init.text:set_reset_devices()
The function sonic_get_stats() references
the function __init set_reset_devices().
This is often because sonic_get_stats lacks a __init
annotation or the annotation of set_reset_devices is wrong.
WARNING: modpost: vmlinux.o(.text+0x529b3b): Section mismatch in reference from the function xtsonic_probe() to the function .init.text:sonic_probe1()
The function xtsonic_probe() references
the function __init sonic_probe1().
This is often because xtsonic_probe lacks a __init
annotation or the annotation of sonic_probe1 is wrong.
Fixes: 74f2a5f0ef64 ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Finn Thain <fthain@telegraphics.com.au> Cc: Chris Zankel <chris@zankel.net> Cc: linux-xtensa@linux-xtensa.org Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Acked-by: Max Filippov <jcmvbkbc@gmail.com> Link: https://lore.kernel.org/r/20211130063947.7529-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jann Horn points out that there is another possible race wrt Unix domain
socket garbage collection, somewhat reminiscent of the one fixed in
commit cbcf01128d0a ("af_unix: fix garbage collect vs MSG_PEEK").
See the extended comment about the garbage collection requirements added
to unix_peek_fds() by that commit for details.
The race comes from how we can locklessly look up a file descriptor just
as it is in the process of being closed, and with the right artificial
timing (Jann added a few strategic 'mdelay(500)' calls to do that), the
Unix domain socket garbage collector could see the reference count
decrement of the close() happen before fget() took its reference to the
file and the file was attached onto a new file descriptor.
This is all (intentionally) correct on the 'struct file *' side, with
RCU lookups and lockless reference counting very much part of the
design. Getting that reference count out of order isn't a problem per
se.
But the garbage collector can get confused by seeing this situation of
having seen a file not having any remaining external references and then
seeing it being attached to an fd.
In commit cbcf01128d0a ("af_unix: fix garbage collect vs MSG_PEEK") the
fix was to serialize the file descriptor install with the garbage
collector by taking and releasing the unix_gc_lock.
That's not really an option here, but since this all happens when we are
in the process of looking up a file descriptor, we can instead simply
just re-check that the file hasn't been closed in the meantime, and just
re-do the lookup if we raced with a concurrent close() of the same file
descriptor.
Some uses cases repeatedly get and put references to the same file, but
the only exposed interface is doing these one at the time. As each of
these entail an atomic inc or dec on a shared structure, that cost can
add up.
Add fget_many(), which works just like fget(), except it takes an
argument for how many references to get on the file. Ditto fput_many(),
which can drop an arbitrary number of references to a file.
Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to remove the fsl-sata module in the PPC64 GNU/Linux
leads to the following warning:
------------[ cut here ]------------
remove_proc_entry: removing non-empty directory 'irq/69',
leaking at least 'fsl-sata[ff0221000.sata]'
WARNING: CPU: 3 PID: 1048 at fs/proc/generic.c:722
.remove_proc_entry+0x20c/0x220
IRQMASK: 0
NIP [c00000000033826c] .remove_proc_entry+0x20c/0x220
LR [c000000000338268] .remove_proc_entry+0x208/0x220
Call Trace:
.remove_proc_entry+0x208/0x220 (unreliable)
.unregister_irq_proc+0x104/0x140
.free_desc+0x44/0xb0
.irq_free_descs+0x9c/0xf0
.irq_dispose_mapping+0x64/0xa0
.sata_fsl_remove+0x58/0xa0 [sata_fsl]
.platform_drv_remove+0x40/0x90
.device_release_driver_internal+0x160/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
---[ end trace 0ea876d4076908f5 ]---
The driver creates the mapping by calling irq_of_parse_and_map(),
so it also has to dispose the mapping. But the easy way out is to
simply use platform_get_irq() instead of irq_of_parse_map(). Also
we should adapt return value checking and propagate error values.
In this case the mapping is not managed by the device but by
the of core, so the device has not to dispose the mapping.
Fixes: faf0b2e5afe7 ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller") Cc: stable@vger.kernel.org Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux,
a bug is reported:
==================================================================
BUG: Unable to handle kernel data access on read at 0x80000800805b502c
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000388a4] .ioread32+0x4/0x20
LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl]
Call Trace:
.free_irq+0x1c/0x4e0 (unreliable)
.ata_host_stop+0x74/0xd0 [libata]
.release_nodes+0x330/0x3f0
.device_release_driver_internal+0x178/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
.__se_sys_delete_module+0x1ec/0x2d0
.system_call_exception+0xfc/0x1f0
system_call_common+0xf8/0x200
==================================================================
The triggering of the BUG is shown in the following stack:
The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should
not be executed in drv->remove. These functions should be executed in
host_stop after port_stop. Therefore, we move these functions to the
new function sata_fsl_host_stop and bind the new function to host_stop.
Fixes: faf0b2e5afe7 ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller") Cc: stable@vger.kernel.org Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'kprobe::data_size' is unsigned, thus it can not be negative. But if
user sets it enough big number (e.g. (size_t)-8), the result of 'data_size
+ sizeof(struct kretprobe_instance)' becomes smaller than sizeof(struct
kretprobe_instance) or zero. In result, the kretprobe_instance are
allocated without enough memory, and kretprobe accesses outside of
allocated memory.
To avoid this issue, introduce a max limitation of the
kretprobe::data_size. 4KB per instance should be OK.
IPCB/IP6CB need to be initialized when processing outbound v4 or v6 pkts
in the codepath of vrf device xmit function so that leftover garbage
doesn't cause futher code that uses the CB to incorrectly process the
pkt.
One occasion of the issue might occur when MPLS route uses the vrf
device as the outgoing device such as when the route is added using "ip
-f mpls route add <label> dev <vrf>" command.
The problems seems to exist since day one. Hence I put the day one
commits on the Fixes tags.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver") Fixes: 35402e313663 ("net: Add IPv6 support to VRF device") Cc: stable@vger.kernel.org Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20211130162637.3249-1-ssuryaextr@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definition of macro MOTO_SROM_BUG is:
#define MOTO_SROM_BUG (lp->active == 8 && (get_unaligned_le32(
dev->dev_addr) & 0x00ffffff) == 0x3e0008)
and the if statement
if (MOTO_SROM_BUG) lp->active = 0;
using this macro indicates lp->active could be 8. If lp->active is 8 and
the second comparison of this macro is false. lp->active will remain 8 in:
lp->phy[lp->active].gep = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].rst = (*p ? p : NULL); p += (2 * (*p) + 1);
lp->phy[lp->active].mc = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ana = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].fdx = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].ttm = get_unaligned_le16(p); p += 2;
lp->phy[lp->active].mci = *p;
However, the length of array lp->phy is 8, so array overflows can occur.
To fix these possible array overflows, we first check lp->active and then
return -EINVAL if it is greater or equal to ARRAY_SIZE(lp->phy) (i.e. 8).
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Teng Qi <starmiku1207184332@gmail.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The if statement:
if (port >= DSAF_GE_NUM)
return;
limits the value of port less than DSAF_GE_NUM (i.e., 8).
However, if the value of port is 6 or 7, an array overflow could occur:
port_rst_off = dsaf_dev->mac_cb[port]->port_rst_off;
because the length of dsaf_dev->mac_cb is DSAF_MAX_PORT_NUM (i.e., 6).
To fix this possible array overflow, we first check port and if it is
greater than or equal to DSAF_MAX_PORT_NUM, the function returns.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Teng Qi <starmiku1207184332@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We can race where iscsi_session_recovery_timedout() has woken up the error
handler thread and it's now setting the devices to offline, and
session_recovery_timedout()'s call to scsi_target_unblock() is also trying
to set the device's state to transport-offline. We can then get a mix of
states.
For the case where we can't relogin we want the devices to be in
transport-offline so when we have repaired the connection
__iscsi_unblock_session() can set the state back to running.
Set the device state then call into libiscsi to wake up the error handler.
During the suspend is in process, thermal_zone_device_update bails out
thermal zone re-evaluation for any sensor trip violation without
setting next valid trip to that sensor. It assumes during resume
it will re-evaluate same thermal zone and update trip. But when it is
in suspend temperature goes down and on resume path while updating
thermal zone if temperature is less than previously violated trip,
thermal zone set trip function evaluates the same previous high and
previous low trip as new high and low trip. Since there is no change
in high/low trip, it bails out from thermal zone set trip API without
setting any trip. It leads to a case where sensor high trip or low
trip is disabled forever even though thermal zone has a valid high
or low trip.
During thermal zone device init, reset thermal zone previous high
and low trip. It resolves above mentioned scenario.
Signed-off-by: Manaf Meethalavalappu Pallikunhi <manafm@codeaurora.org> Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a difference in how architectures treat "mem=" option. For some
that is an amount of online memory, for s390 and x86 this is the limiting
max address. Some memblock api like memblock_enforce_memory_limit()
take limit argument and explicitly treat it as the size of online memory,
and use __find_max_addr to convert it to an actual max address. Current
s390 usage:
yields different results depending on presence of memory holes (offline
memory blocks in between online memory). If there are no memory holes
limit == max_addr in memblock_enforce_memory_limit() and it does trim
online memory and reserved memory regions. With memory holes present it
actually does nothing.
Since we already use memblock_remove() explicitly to trim online memory
regions to potential limit (think mem=, kdump, addressing limits, etc.)
drop the usage of memblock_enforce_memory_limit() altogether. Trimming
reserved regions should not be required, since we now use
memblock_set_current_limit() to limit allocations and any explicit memory
reservations above the limit is an actual problem we should not hide.
When WWAN device wake from S3 deep, under thinkpad platform,
WWAN would be disabled. This disable status could be checked
by command 'nmcli r wwan' or 'rfkill list'.
Issue analysis as below:
When host resume from S3 deep, thinkpad_acpi driver would
call hotkey_resume() function. Finnaly, it will use
wan_get_status to check the current status of WWAN device.
During this resume progress, wan_get_status would always
return off even WWAN boot up completely.
In patch V2, Hans said 'sw_state should be unchanged
after a suspend/resume. It's better to drop the
tpacpi_rfk_update_swstate call all together from the
resume path'.
And it's confimed by Lenovo that GWAN is no longer
available from WHL generation because the design does not
match with current pin control.
Signed-off-by: Slark Xiao <slark_xiao@163.com> Link: https://lore.kernel.org/r/20211108060648.8212-1-slark_xiao@163.com Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When kmemdup called failed and register_net_sysctl return NULL, should
return ENOMEM instead of ENOBUFS
Signed-off-by: liuguoqiang <liuguoqiang@uniontech.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When fixing an issue with PMD sharing and migration, it was discovered via
code inspection that other callers of huge_pmd_unshare potentially have an
issue with cache and tlb flushing.
Use the routine adjust_range_if_pmd_sharing_possible() to calculate worst
case ranges for mmu notifiers. Ensure that this range is flushed if
huge_pmd_unshare succeeds and unmaps a PUD_SUZE area.
Link: http://lkml.kernel.org/r/20180823205917.16297-3-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Michal Hocko <mhocko@kernel.org> Cc: Jerome Glisse <jglisse@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mechanism in use to allow the client to see the results of COPY/CLONE
is to drop those pages from the pagecache. This forces the client to read
those pages once more from the server. However, truncate_pagecache_range()
zeros out partial pages instead of dropping them. Let us instead use
invalidate_inode_pages2_range() with full-page offsets to ensure the client
properly sees the results of COPY/CLONE operations.
Currently, the exit_shm() function not designed to work properly when
task->sysvshm.shm_clist holds shm objects from different IPC namespaces.
This is a real pain when sysctl kernel.shm_rmid_forced = 1, because it
leads to use-after-free (reproducer exists).
This is an attempt to fix the problem by extending exit_shm mechanism to
handle shm's destroy from several IPC ns'es.
To achieve that we do several things:
1. add a namespace (non-refcounted) pointer to the struct shmid_kernel
2. during new shm object creation (newseg()/shmget syscall) we
initialize this pointer by current task IPC ns
3. exit_shm() fully reworked such that it traverses over all shp's in
task->sysvshm.shm_clist and gets IPC namespace not from current task
as it was before but from shp's object itself, then call
shm_destroy(shp, ns).
Note: We need to be really careful here, because as it was said before
(1), our pointer to IPC ns non-refcnt'ed. To be on the safe side we
using special helper get_ipc_ns_not_zero() which allows to get IPC ns
refcounter only if IPC ns not in the "state of destruction".
Q/A
Q: Why can we access shp->ns memory using non-refcounted pointer?
A: Because shp object lifetime is always shorther than IPC namespace
lifetime, so, if we get shp object from the task->sysvshm.shm_clist
while holding task_lock(task) nobody can steal our namespace.
Q: Does this patch change semantics of unshare/setns/clone syscalls?
A: No. It's just fixes non-covered case when process may leave IPC
namespace without getting task->sysvshm.shm_clist list cleaned up.
Link: https://lkml.kernel.org/r/67bb03e5-f79c-1815-e2bf-949c67047418@colorfullife.com Link: https://lkml.kernel.org/r/20211109151501.4921-1-manfred@colorfullife.com Fixes: ab602f79915 ("shm: make exit_shm work proportional to task activity") Co-developed-by: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Manfred Spraul <manfred@colorfullife.com> Signed-off-by: Alexander Mikhalitsyn <alexander.mikhalitsyn@virtuozzo.com> Cc: "Eric W. Biederman" <ebiederm@xmission.com> Cc: Davidlohr Bueso <dave@stgolabs.net> Cc: Greg KH <gregkh@linuxfoundation.org> Cc: Andrei Vagin <avagin@gmail.com> Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Cc: Vasily Averin <vvs@virtuozzo.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xen frontends shouldn't BUG() in case of illegal data received from
their backends. So replace the BUG_ON()s when reading illegal data from
the ring page with negative return values.
Today netfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Note that only the tx queue needs special id handling, as for the rx
queue the id is equal to the index in the ring page.
Introduce a new indicator for the device whether it is broken and let
the device stop working when it is set. Set this indicator in case the
backend sets any weird data.
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tx_skb_freelist elements are in a single linked list with the
request id used as link reference. The per element link field is in a
union with the skb pointer of an in use request.
Move the link reference out of the union in order to enable a later
reuse of it for requests which need a populated skb pointer.
Rename add_id_to_freelist() and get_id_from_freelist() to
add_id_to_list() and get_id_from_list() in order to prepare using
those for other lists as well. Define ~0 as value to indicate the end
of a list and place that value into the link for a request not being
on the list.
When freeing a skb zero the skb pointer in the request. Use a NULL
value of the skb pointer instead of skb_entry_is_link() for deciding
whether a request has a skb linked to it.
Remove skb_entry_set_link() and open code it instead as it is really
trivial now.
Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to avoid a malicious backend being able to influence the local
processing of a request build the request locally first and then copy
it to the ring page. Any reading from the request influencing the
processing in the frontend needs to be done on the local instance.
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to avoid problems in case the backend is modifying a response
on the ring page while the frontend has already seen it, just read the
response into a local buffer in one go and then operate on that buffer
only.
Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Today blkfront will trust the backend to send only sane response data.
In order to avoid privilege escalations or crashes in case of malicious
backends verify the data to be within expected limits. Especially make
sure that the response always references an outstanding request.
Introduce a new state of the ring BLKIF_STATE_ERROR which will be
switched to in case an inconsistency is being detected. Recovering from
this state is possible only via removing and adding the virtual device
again (e.g. via a suspend/resume cycle).
Make all warning messages issued due to valid error responses rate
limited in order to avoid message floods being triggered by a malicious
backend.
In order to avoid a malicious backend being able to influence the local
copy of a request build the request locally first and then copy it to
the ring page instead of doing it the other way round as today.
In order to avoid problems in case the backend is modifying a response
on the ring page while the frontend has already seen it, just read the
response into a local buffer in one go and then operate on that buffer
only.
Checking buf->flags should be done before the pipe_buf_release() is called
on the pipe buffer, since releasing the buffer might modify the flags.
This is exactly what page_cache_pipe_buf_release() does, and which results
in the same VM_BUG_ON_PAGE(PageLRU(page)) that the original patch was
trying to fix.
For the above two UAF, the root cause is that the nfc_dev_up can race
between the nci_unregister_device routine. Therefore, this patch
introduce NCI_UNREG flag to easily eliminate the possible race. In
addition, the mutex_lock in nci_close_device can act as a barrier.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Fixes: 6a2968aaf50c ("NFC: basic NCI protocol implementation") Reviewed-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20211116152732.19238-1-linma@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To clear a user buffer we cannot simply use memset, we have to use
clear_user(). With a virtio-mem device that registers a vmcore_cb and
has some logically unplugged memory inside an added Linux memory block,
I can easily trigger a BUG by copying the vmcore via "cp":
Some x86-64 CPUs have a CPU feature called "Supervisor Mode Access
Prevention (SMAP)", which is used to detect wrong access from the kernel
to user buffers like this: SMAP triggers a permissions violation on
wrong access. In the x86-64 variant of clear_user(), SMAP is properly
handled via clac()+stac().
To fix, properly use clear_user() when we're dealing with a user buffer.
Link: https://lkml.kernel.org/r/20211112092750.6921-1-david@redhat.com Fixes: 997c136f518c ("fs/proc/vmcore.c: add hook to read_from_oldmem() to check for non-ram pages") Signed-off-by: David Hildenbrand <david@redhat.com> Acked-by: Baoquan He <bhe@redhat.com> Cc: Dave Young <dyoung@redhat.com> Cc: Baoquan He <bhe@redhat.com> Cc: Vivek Goyal <vgoyal@redhat.com> Cc: Philipp Rudo <prudo@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "used length" reported by calling vhost_add_used() must be the
number of bytes written by the device (using "in" buffers).
In vhost_vsock_handle_tx_kick() the device only reads the guest
buffers (they are all "out" buffers), without writing anything,
so we must pass 0 as "used length" to comply virtio spec.
Fixes: 433fc58e6bf2 ("VSOCK: Introduce vhost_vsock.ko") Cc: stable@vger.kernel.org Reported-by: Halil Pasic <pasic@linux.ibm.com> Suggested-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Link: https://lore.kernel.org/r/20211122163525.294024-2-sgarzare@redhat.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Halil Pasic <pasic@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When __unmap_hugepage_range() calls to huge_pmd_unshare() succeed, a TLB
flush is missing. This TLB flush must be performed before releasing the
i_mmap_rwsem, in order to prevent an unshared PMDs page from being
released and reused before the TLB flush took place.
Arguably, a comprehensive solution would use mmu_gather interface to
batch the TLB flushes and the PMDs page release, however it is not an
easy solution: (1) try_to_unmap_one() and try_to_migrate_one() also call
huge_pmd_unshare() and they cannot use the mmu_gather interface; and (2)
deferring the release of the page reference for the PMDs page until
after i_mmap_rwsem is dropeed can confuse huge_pmd_unshare() into
thinking PMDs are shared when they are not.
Fix __unmap_hugepage_range() by adding the missing TLB flush, and
forcing a flush when unshare is successful.
Fixes: 24669e58477e ("hugetlb: use mmu_gather instead of a temporary linked list for accumulating pages)" # 3.6 Signed-off-by: Nadav Amit <namit@vmware.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When pid filtering is activated in an instance, all of the events trace
files for that instance has the PID_FILTER flag set. This determines
whether or not pid filtering needs to be done on the event, otherwise the
event is executed as normal.
If pid filtering is enabled when an event is created (via a dynamic event
or modules), its flag is not updated to reflect the current state, and the
events are not filtered properly.
While testing BIG TCP patch series, I was expecting that TCP_RR workloads
with 80KB requests/answers would send one 80KB TSO packet,
then being received as a single GRO packet.
It turns out this was not happening, and the root cause was that
cubic Hystart ACK train was triggering after a few (2 or 3) rounds of RPC.
Hystart was wrongly setting CWND/SSTHRESH to 30, while my RPC
needed a budget of ~20 segments.
Ideally these TCP_RR flows should not exit slow start.
Cubic Hystart should reset itself at each round, instead of assuming
every TCP flow is a bulk one.
Note that even after this patch, Hystart can still trigger, depending
on scheduling artifacts, but at a higher CWND/SSTHRESH threshold,
keeping optimal TSO packet sizes.
Tested:
ip link set dev eth0 gro_ipv6_max_size 131072 gso_ipv6_max_size 131072
nstat -n; netperf -H ... -t TCP_RR -l 5 -- -r 80000,80000 -K cubic; nstat|egrep "Ip6InReceives|Hystart|Ip6OutRequests"
Commit 39fbef4b0f77 ("PM: hibernate: Get block device exclusively in
swsusp_check()") changed the opening mode of the block device to
(FMODE_READ | FMODE_EXCL).
In the corresponding calls to swsusp_close(), the mode is still just
FMODE_READ which triggers the warning in blkdev_flush_mapping() on
resume from hibernate.
So, use the mode (FMODE_READ | FMODE_EXCL) also when closing the
device.
Fixes: 39fbef4b0f77 ("PM: hibernate: Get block device exclusively in swsusp_check()") Signed-off-by: Thomas Zeitlhofer <thomas.zeitlhofer+lkml@ze-it.at> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ->gem_create_object() functions are supposed to return NULL if there
is an error. None of the callers expect error pointers so returing one
will lead to an Oops. See drm_gem_vram_create(), for example.
While looping over shost's sdev list it is possible that one
of the drives is getting removed and its sas_target object is
freed but its sdev object remains intact.
Consequently, a kernel panic can occur while the driver is trying to access
the sas_address field of sas_target object without also checking the
sas_target object for NULL.
Link: https://lore.kernel.org/r/20211117104909.2069-1-sreekanth.reddy@broadcom.com Fixes: f92363d12359 ("[SCSI] mpt3sas: add new driver supporting 12GB SAS") Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When CONFIG_FORTIFY_SOURCE is set, memcpy() checks the potential
buffer overflow and panics. The code in sofcpga bootstrapping
contains the memcpy() calls are mistakenly translated as the shorter
size, hence it triggers a panic as if it were overflowing.
This patch changes the secondary_trampoline and *_end definitions
to arrays for avoiding the false-positive crash above.
The failure to retrieve post-op attributes has no bearing on whether or
not the clone operation itself was successful. We must therefore ignore
the return value of decode_getfattr() when looking at the success or
failure of nfs4_xdr_dec_clone().
This patch fixes an issue that an u32 netlink value is handled as a
signed enum value which doesn't fit into the range of u32 netlink type.
If it's handled as -1 value some BIT() evaluation ends in a
shift-out-of-bounds issue. To solve the issue we set the to u32 max which
is s32 "-1" value to keep backwards compatibility and let the followed enum
values start counting at 0. This brings the compiler to never handle the
enum as signed and a check if the value is above NL802154_IFTYPE_MAX should
filter -1 out.
Fixes: f3ea5e44231a ("ieee802154: add new interface command") Signed-off-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20211112030916.685793-1-aahringo@redhat.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
snd_ctl_remove() has to be called with card->controls_rwsem held (when
called after the card instantiation). This patch add the missing
rwsem calls around it.
The GPIO controller is also an interrupt controller provider and is
currently missing the appropriate 'interrupt-controller' and
'#interrupt-cells' properties to denote that.
Fixes: fb026d3de33b ("ARM: BCM5301X: Add Broadcom's bus-axi to the DTS file") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a event is filtered by pid and a trigger that requires processing of
the event to happen is a attached to the event, the discard portion does
not take the pid filtering into account, and the event will then be
recorded when it should not have been.
If the xenstore page hasn't been allocated properly, reading the value
of the related hvm_param (HVM_PARAM_STORE_PFN) won't actually return
error. Instead, it will succeed and return zero. Instead of attempting
to xen_remap a bad guest physical address, detect this condition and
return early.
Note that although a guest physical address of zero for
HVM_PARAM_STORE_PFN is theoretically possible, it is not a good choice
and zero has never been validly used in that capacity.
Also recognize all bits set as an invalid value.
For 32-bit Linux, any pfn above ULONG_MAX would get truncated. Pfns
above ULONG_MAX should never be passed by the Xen tools to HVM guests
anyway, so check for this condition and return early.
In case of errors in xenbus_init (e.g. missing xen_store_gfn parameter),
we goto out_error but we forget to reset xen_store_domain_type to
XS_UNKNOWN. As a consequence xenbus_probe_initcall and other initcalls
will still try to initialize xenstore resulting into a crash at boot.
It is possible to trigger a crash by splicing anon pipe bufs to the fuse
device.
The reason for this is that anon_pipe_buf_release() will reuse buf->page if
the refcount is 1, but that page might have already been stolen and its
flags modified (e.g. PG_lru added).
This happens in the unlikely case of fuse_dev_splice_write() getting around
to calling pipe_buf_release() after a page has been stolen, added to the
page cache and removed from the page cache.
Fix by calling pipe_buf_release() right after the page was inserted into
the page cache. In this case the page has an elevated refcount so any
release function will know that the page isn't reusable.
The master and next_conj of rcs_ops are used for iterating the
resource list entries, and currently those are supposed to return the
current value. The problem is that next_conf may go over the last
entry before the loop abort condition is evaluated, and it may return
the "current" value that is beyond the array size. It was caught
recently as a GPF, for example.
Those return values are, however, never actually evaluated, hence
basically we don't have to consider the current value as the return at
all. By dropping those return values, the potential out-of-range
access above is also fixed automatically.
This patch changes the return type of master and next_conj callbacks
to void and drop the superfluous code accordingly.
This is a partial revert of commit 29bc22ac5e5b ("binder: use euid from cred instead of using task").
Setting sender_euid using proc->cred caused some Android system test
regressions that need further investigation. It is a partial
reversion because subsequent patches rely on proc->cred.
Fixes: 29bc22ac5e5b ("binder: use euid from cred instead of using task") Cc: stable@vger.kernel.org # 4.4+ Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Signed-off-by: Todd Kjos <tkjos@google.com>
Change-Id: I9b1769a3510fed250bb21859ef8beebabe034c66 Link: https://lore.kernel.org/r/20211112180720.2858135-1-tkjos@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the circular lock dependency and unbalanced unlock of addess0_mutex
introduced when fixing an address0_mutex enumeration retry race in commit ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Make sure locking order between port_dev->status_lock and address0_mutex
is correct, and that address0_mutex is not unlocked in hub_port_connect
"done:" codepath which may be reached without locking address0_mutex
Fixes: 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race") Cc: <stable@vger.kernel.org> Reported-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20211123101656.1113518-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4
The address0_mutex exists to prevent this across both xhci roothubs.
If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.
Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.
Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.
Cc: <stable@vger.kernel.org> Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel") Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the USB serial option driver support for the Fibocom
FM101-GL Cat.6
LTE modules as there are actually several different variants.
- VID:PID 2cb7:01a2, FM101-GL are laptop M.2 cards (with
MBIM interfaces for /Linux/Chrome OS)
- VID:PID 2cb7:01a4, FM101-GL for laptop debug M.2 cards(with adb
interface for /Linux/Chrome OS)
Supply additional checks in order to prevent unexpected results.
Fixes: b892bf75b2034 ("ion: Switch ion to use dma-buf") Suggested-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tegra_powergate_power_up() has a typo in the error code path where it
will try to disable clocks twice, fix it. In practice that error never
happens, so this is a minor correction.
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30 Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124 Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30 Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of maintaining a single-linked list of devices that must be
searched linearly in .remove() just use spi_set_drvdata() to remember the
link between the spi device and the driver struct. Then the global list
and the next member can be dropped.
This simplifies the driver, reduces the memory footprint and the time to
search the list. Also it makes obvious that there is always a corresponding
driver struct for a given device in .remove(), so the error path for
!max3421_hcd can be dropped, too.
As a side effect this fixes a data inconsistency when .probe() races with
itself for a second max3421 device in manipulating max3421_hcd_list. A
similar race is fixed in .remove(), too.
The recent fix for DAPM to correct the kctl change notification by the
commit 5af82c81b2c4 ("ASoC: DAPM: Fix missing kctl change
notifications") caused other regressions since it changed the behavior
of snd_soc_dapm_set_pin() that is called from several API functions.
Formerly it returned always 0 for success, but now it returns 0 or 1.
This patch addresses it, restoring the old behavior of
snd_soc_dapm_set_pin() while keeping the fix in
snd_soc_dapm_put_pin_switch().
When a packet is fragmented by batman-adv, the original batman-adv header
is not modified. Only a new fragmentation is inserted between the original
one and the ethernet header. The code must therefore make sure that it has
a writable region of this size in the skbuff head.
But it is not useful to always reallocate the skbuff by this size even when
there would be more than enough headroom still in the skb. The reallocation
is just to costly during in this codepath.
Fixes: ee75ed88879a ("batman-adv: Fragment and send skbs larger than mtu") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[ bp: 4.9 backported: adjust context. ] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The batadv net_device is trying to propagate the needed_headroom and
needed_tailroom from the lower devices. This is needed to avoid cost
intensive reallocations using pskb_expand_head during the transmission.
But the fragmentation code split the skb's without adding extra room at the
end/beginning of the various fragments. This reduced the performance of
transmissions over complex scenarios (batadv on vxlan on wireguard) because
the lower devices had to perform the reallocations at least once.
Fixes: ee75ed88879a ("batman-adv: Fragment and send skbs larger than mtu") Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[ bp: 4.9 backported: adjust context. ] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a batman-adv packets has to be fragmented, then the original batman-adv
packet header is not stripped away. Instead, only a new header is added in
front of the packet after it was split.
This size must be considered to avoid cost intensive reallocations during
the transmission through the various device layers.
Fixes: 7bca68c7844b ("batman-adv: Add lower layer needed_(head|tail)room to own ones") Reported-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Scenario:
* Multicast frame send from BLA backbone gateways (multiple nodes
with their bat0 bridged together, with BLA enabled) sharing the same
LAN to nodes in the mesh
Issue:
* Nodes receive the frame multiple times on bat0 from the mesh,
once from each foreign BLA backbone gateway which shares the same LAN
with another
For multicast frames via batman-adv broadcast packets coming from the
same BLA backbone but from different backbone gateways duplicates are
currently detected via a CRC history of previously received packets.
However this CRC so far was not performed for multicast frames received
via batman-adv unicast packets. Fixing this by appyling the same check
for such packets, too.
Room for improvements in the future: Ideally we would introduce the
possibility to not only claim a client, but a complete originator, too.
This would allow us to only send a multicast-in-unicast packet from a BLA
backbone gateway claiming the node and by that avoid potential redundant
transmissions in the first place.
Scenario:
* Multicast frame send from a BLA backbone (multiple nodes with
their bat0 bridged together, with BLA enabled)
Issue:
* BLA backbone nodes receive the frame multiple times on bat0
For multicast frames received via batman-adv broadcast packets the
originator of the broadcast packet is checked before decapsulating and
forwarding the frame to bat0 (batadv_bla_is_backbone_gw()->
batadv_recv_bcast_packet()). If it came from a node which shares the
same BLA backbone with us then it is not forwarded to bat0 to avoid a
loop.
When sending a multicast frame in a non-4-address batman-adv unicast
packet we are currently missing this check - and cannot do so because
the batman-adv unicast packet has no originator address field.
However, we can simply fix this on the sender side by only sending the
multicast frame via unicasts to interested nodes which do not share the
same BLA backbone with us. This also nicely avoids some unnecessary
transmissions on mesh side.
Note that no infinite loop was observed, probably because of dropping
via batadv_interface_tx()->batadv_bla_tx(). However the duplicates still
utterly confuse switches/bridges, ICMPv6 duplicate address detection and
neighbor discovery and therefore leads to long delays before being able
to establish TCP connections, for instance. And it also leads to the Linux
bridge printing messages like:
"br-lan: received packet on eth1 with own address as source address ..."
Fixes: fe2da6ff27c7 ("batman-adv: Modified forwarding behaviour for multicast packets") Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[ bp: 4.9 backport: drop usage in non-existing batadv_mcast_forw_*. ] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The own OGM check is currently misplaced and can lead to the following
issues:
For one thing we might receive an aggregated OGM from a neighbor node
which has our own OGM in the first place. We would then not only skip
our own OGM but erroneously also any other, following OGM in the
aggregate.
For another, we might receive an OGM aggregate which has our own OGM in
a place other then the first one. Then we would wrongly not skip this
OGM, leading to populating the orginator and gateway table with ourself.
The batman-adv fragmentation packets have the design problem that they
cannot be refragmented and cannot handle padding by the underlying link.
The latter often leads to problems when networks are incorrectly configured
and don't use a common MTU.
The sender could for example fragment a 1271 byte frame (plus external
ethernet header (14) and batadv unicast header (10)) to fit in a 1280 bytes
large MTU of the underlying link (max. 1294 byte frames). This would create
a 1294 bytes large frame (fragment 2) and a 55 bytes large frame
(fragment 1). The extra 54 bytes are the fragment header (20) added to each
fragment and the external ethernet header (14) for the second fragment.
Let us assume that the next hop is then not able to transport 1294 bytes to
its next hop. The 1294 byte large frame will be dropped but the 55 bytes
large fragment will still be forwarded to its destination.
Or let us assume that the underlying hardware requires that each frame has
a minimum size (e.g. 60 bytes). Then it will pad the 55 bytes frame to 60
bytes. The receiver of the 60 bytes frame will no longer be able to
correctly assemble the two frames together because it is not aware that 5
bytes of the 60 bytes frame are padding and don't belong to the reassembled
frame.
This can partly be avoided by splitting frames more equally. In this
example, the 675 and 674 bytes large fragment frames could both potentially
reach its destination without being too large or too small.
Reported-by: Martin Weinelt <martin@darmstadt.freifunk.net> Fixes: ee75ed88879a ("batman-adv: Fragment and send skbs larger than mtu") Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: Linus Lüssing <linus.luessing@c0d3.blue> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[ bp: 4.9 backported: adjust context. ] Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
amdgpu_connector_vga_get_modes missed function amdgpu_get_native_mode
which assign amdgpu_encoder->native_mode with *preferred_mode result in
amdgpu_encoder->native_mode.clock always be 0. That will cause
amdgpu_connector_set_property returned early on:
if ((rmx_type != DRM_MODE_SCALE_NONE) &&
(amdgpu_encoder->native_mode.clock == 0))
when we try to set scaling mode Full/Full aspect/Center.
Add the missing function to amdgpu_connector_vga_get_mode can fix this.
It also works on dvi connectors because
amdgpu_connector_dvi_helper_funcs.get_mode use the same method.
If the userspace tools switch from NL80211_IFTYPE_P2P_GO to
NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), it
does not call the cleanup cfg80211_stop_ap(), this leads to the
initialization of in-use data. For example, this path re-init the
sdata->assigned_chanctx_list while it is still an element of
assigned_vifs list, and makes that linked list corrupt.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com> Reported-by: syzbot+bbf402b783eeb6d908db@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20211027173722.777287-1-phind.uet@gmail.com Cc: stable@vger.kernel.org Fixes: ac800140c20e ("cfg80211: .stop_ap when interface is going down") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sticon_build_attr() checked the reverse argument and flipped
background and foreground color, but returned the non-reverse
value afterwards. Fix this and also add two local variables
for foreground and background color to make the code easier
to read.
Ordered work functions aren't guaranteed to be handled by the same thread
which executed the normal work functions. The only way execution between
normal/ordered functions is synchronized is via the WORK_DONE_BIT,
unfortunately the used bitops don't guarantee any ordering whatsoever.
This manifested as seemingly inexplicable crashes on ARM64, where
async_chunk::inode is seen as non-null in async_cow_submit which causes
submit_compressed_extents to be called and crash occurs because
async_chunk::inode suddenly became NULL. The call trace was similar to:
pc : submit_compressed_extents+0x38/0x3d0
lr : async_cow_submit+0x50/0xd0
sp : ffff800015d4bc20
Fix this by adding respective barrier calls which ensure that all
accesses preceding setting of WORK_DONE_BIT are strictly ordered before
setting the flag. At the same time add a read barrier after reading of
WORK_DONE_BIT in run_ordered_work which ensures all subsequent loads
would be strictly ordered after reading the bit. This in turn ensures
are all accesses before WORK_DONE_BIT are going to be strictly ordered
before any access that can occur in ordered_func.
Reported-by: Chris Murphy <lists@colorremedies.com> Fixes: 08a9ff326418 ("btrfs: Added btrfs_workqueue_struct implemented ordered execution based on kernel workqueue") CC: stable@vger.kernel.org # 4.4+ Link: https://bugzilla.redhat.com/show_bug.cgi?id=2011928 Reviewed-by: Josef Bacik <josef@toxicpanda.com> Tested-by: Chris Murphy <chris@colorremedies.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When kmemleak is enabled for SLOB, system does not boot and does not
print anything to the console. At the very early stage in the boot
process we hit infinite recursion from kmemleak_init() and eventually
kernel crashes.
kmemleak_init() specifies SLAB_NOLEAKTRACE for KMEM_CACHE(), but
kmem_cache_create_usercopy() removes it because CACHE_CREATE_MASK is not
valid for SLOB.
Let's fix CACHE_CREATE_MASK and make kmemleak work with SLOB
Link: https://lkml.kernel.org/r/20211115020850.3154366-1-rkovhaev@gmail.com Fixes: d8843922fba4 ("slab: Ignore internal flags in cache creation") Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com> Acked-by: Vlastimil Babka <vbabka@suse.cz> Reviewed-by: Muchun Song <songmuchun@bytedance.com> Cc: Christoph Lameter <cl@linux.com> Cc: Pekka Enberg <penberg@kernel.org> Cc: David Rientjes <rientjes@google.com> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Glauber Costa <glommer@parallels.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As stated in the bonding doc, trans_start must be set manually for drivers
using NETIF_F_LLTX:
Drivers that use NETIF_F_LLTX flag must also update
netdev_queue->trans_start. If they do not, then the ARP monitor will
immediately fail any slaves using that driver, and those slaves will stay
down.
According to the latest uncore document, COMP_BUF_OCCUPANCY (0xd5) event
can be collected on 2-3 counters. Update uncore IIO event constraints for
Skylake Server.
Fixes: cd34cd97b7b4 ("perf/x86/intel/uncore: Add Skylake server uncore support") Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Link: https://lore.kernel.org/r/20211115090334.3789-3-alexander.antonov@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
According Uncore Reference Manual: any of the CHA events may be filtered
by Thread/Core-ID by using tid modifier in CHA Filter 0 Register.
Update skx_cha_hw_config() to follow Uncore Guide.
Fixes: cd34cd97b7b4 ("perf/x86/intel/uncore: Add Skylake server uncore support") Signed-off-by: Alexander Antonov <alexander.antonov@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Link: https://lore.kernel.org/r/20211115090334.3789-2-alexander.antonov@linux.intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The root cause for this race is concluded below:
1. The rfkill_blocked (USE) in nfc_dev_up is supposed to be placed after
the device_is_registered check.
2. Since the netlink operations are possible just after the device_add
in nfc_register_device, the nfc_dev_up() can happen anywhere during the
rfkill creation process, which leads to data race.
This patch reorder these actions to permit
1. Once device_del is finished, the nfc_dev_up cannot dereference the
rfkill object.
2. The rfkill_register need to be placed after the device_add of nfc_dev
because the parent device need to be created first. So this patch keeps
the order but inject device_lock to prevent the data race.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Fixes: be055b2f89b5 ("NFC: RFKILL support") Reviewed-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Link: https://lore.kernel.org/r/20211116152652.19217-1-linma@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
thread-A in nci_request() | thread-B in nci_close_device()
| mutex_lock(&ndev->req_lock);
test_bit(NCI_UP, &ndev->flags); |
... | test_and_clear_bit(NCI_UP, &ndev->flags)
mutex_lock(&ndev->req_lock); |
|
This race will allow __nci_request() to be awaked while the device is
getting removed.
Similar to commit e2cb6b891ad2 ("bluetooth: eliminate the potential race
condition when removing the HCI controller"). this patch alters the
function sequence in nci_request() to prevent the data races between the
nci_close_device().
Signed-off-by: Lin Ma <linma@zju.edu.cn> Fixes: 6a2968aaf50c ("NFC: basic NCI protocol implementation") Link: https://lore.kernel.org/r/20211115145600.8320-1-linma@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If 'led_classdev_register()' fails, some additional resources should be
released.
Add the missing 'i8042_remove_filter()' and 'lis3lv02d_remove_fs()' calls
that are already in the remove function but are missing here.
Fixes: a4c724d0723b ("platform: hp_accel: add a i8042 filter to remove HPQ6000 data from kb bus stream") Fixes: 9e0c79782143 ("lis3lv02d: merge with leds hp disk") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/5a4f218f8f16d2e3a7906b7ca3654ffa946895f8.1636314074.git.christophe.jaillet@wanadoo.fr Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
BCM63XX selects HAVE_LEGACY_CLK but does not provide/support
clk_get_parent(), so add a simple implementation of that
function so that callers of it will build without errors.
Fixes these build errors:
mips-linux-ld: drivers/iio/adc/ingenic-adc.o: in function `jz4770_adc_init_clk_div':
ingenic-adc.c:(.text+0xe4): undefined reference to `clk_get_parent'
mips-linux-ld: drivers/iio/adc/ingenic-adc.o: in function `jz4725b_adc_init_clk_div':
ingenic-adc.c:(.text+0x1b8): undefined reference to `clk_get_parent'
Fixes: e7300d04bd08 ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs." ) Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Cc: Artur Rojek <contact@artur-rojek.eu> Cc: Paul Cercueil <paul@crapouillou.net> Cc: linux-mips@vger.kernel.org Cc: Jonathan Cameron <jic23@kernel.org> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: linux-iio@vger.kernel.org Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Andy Shevchenko <andy.shevchenko@gmail.com> Cc: Russell King <linux@armlinux.org.uk> Cc: bcm-kernel-feedback-list@broadcom.com Cc: Jonas Gorski <jonas.gorski@gmail.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
While issuing VF Reset from the guest OS, the VF driver prints
logs about critical / Overflow error detection. This is not an
actual error since the VF_MBX_ARQLEN register is set to all FF's
for a short period of time and the VF would catch the bits set if
it was reading the register during that spike of time.
This patch introduces an additional check to ignore this condition
since the VF is in reset.
Fixes: 19b73d8efaa4 ("i40evf: Add additional check for reset") Signed-off-by: Surabhi Boob <surabhi.boob@intel.com> Tested-by: Tony Brelinski <tony.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch says:
bnx2x_init_ops.h:640 bnx2x_ilt_client_mem_op()
warn: variable dereferenced before check 'ilt' (see line 638)
Move ilt_cli variable initialization _after_ ilt validation, because
it's unsafe to deref the pointer before validation check.
Fixes: 523224a3b3cd ("bnx2x, cnic, bnx2i: use new FW/HSI") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Nothing protects the access to the per_cpu variable sd_llc_id. When testing
the same CPU (i.e. this_cpu == that_cpu), a race condition exists with
update_top_cache_domain(). One scenario being:
Several header files need info on CONFIG_32BIT or CONFIG_64BIT,
but kconfig symbol BCM63XX does not provide that info. This leads
to many build errors, e.g.:
arch/mips/include/asm/page.h:196:13: error: use of undeclared identifier 'CAC_BASE'
return x - PAGE_OFFSET + PHYS_OFFSET;
arch/mips/include/asm/mach-generic/spaces.h:91:23: note: expanded from macro 'PAGE_OFFSET'
#define PAGE_OFFSET (CAC_BASE + PHYS_OFFSET)
arch/mips/include/asm/io.h:134:28: error: use of undeclared identifier 'CAC_BASE'
return (void *)(address + PAGE_OFFSET - PHYS_OFFSET);
arch/mips/include/asm/mach-generic/spaces.h:91:23: note: expanded from macro 'PAGE_OFFSET'
#define PAGE_OFFSET (CAC_BASE + PHYS_OFFSET)
arch/mips/include/asm/uaccess.h:82:10: error: use of undeclared identifier '__UA_LIMIT'
return (__UA_LIMIT & (addr | (addr + size) | __ua_size(size))) == 0;
Selecting the SYS_HAS_CPU_BMIPS* symbols causes SYS_HAS_CPU_BMIPS to be
set, which then selects CPU_SUPPORT_32BIT_KERNEL, which causes
CONFIG_32BIT to be set. (a bit more indirect than v1 [RFC].)
Fixes: e7300d04bd08 ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: linux-mips@vger.kernel.org Cc: Paul Burton <paulburton@kernel.org> Cc: Maxime Bizon <mbizon@freebox.fr> Cc: Ralf Baechle <ralf@linux-mips.org> Suggested-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix this by defining both ENDIAN macros in
<asm/sfp-machine.h> so that they can be utilized in
<math-emu/soft-fp.h> according to the latter's comment:
/* Allow sfp-machine to have its own byte order definitions. */
(This is what is done in arch/nds32/include/asm/sfp-machine.h.)
This placates these build warnings:
In file included from ../arch/sh/math-emu/math.c:23:
.../include/math-emu/single.h:50:21: warning: "__BIG_ENDIAN" is not defined, evaluates to 0 [-Wundef]
50 | #if __BYTE_ORDER == __BIG_ENDIAN
In file included from ../arch/sh/math-emu/math.c:24:
.../include/math-emu/double.h:59:21: warning: "__BIG_ENDIAN" is not defined, evaluates to 0 [-Wundef]
59 | #if __BYTE_ORDER == __BIG_ENDIAN
Fixes: 4b565680d163 ("sh: math-emu support") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Rich Felker <dalias@libc.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
FRAME_POINTER depends on DEBUG_KERNEL so DWARF_UNWINDER should
depend on DEBUG_KERNEL before selecting FRAME_POINTER.
WARNING: unmet direct dependencies detected for FRAME_POINTER
Depends on [n]: DEBUG_KERNEL [=n] && (M68K || UML || SUPERH [=y]) || ARCH_WANT_FRAME_POINTERS [=n]
Selected by [y]:
- DWARF_UNWINDER [=y]
Fixes: bd353861c735 ("sh: dwarf unwinder support.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Matt Fleming <matt@console-pimps.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Yoshinori Sato <ysato@users.sourceforge.jp> Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Cc: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Rich Felker <dalias@libc.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If KMEM_CACHE or maple_alloc_dev failed, the maple_bus_init() will return 0
rather than error, because the retval is not changed after KMEM_CACHE or
maple_alloc_dev failed.
Fixes: 17be2d2b1c33 ("sh: Add maple bus support for the SEGA Dreamcast.") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Lu Wei <luwei32@huawei.com> Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Signed-off-by: Rich Felker <dalias@libc.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
request_irq is marked __must_check, but the call in shx3_prepare_cpus
has a void return type, so it can't propagate failure to the caller.
Follow cues from hexagon and just print an error.
Fixes: c7936b9abcf5 ("sh: smp: Hook in to the generic IPI handler for SH-X3 SMP.") Cc: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com> Cc: Paul Mundt <lethal@linux-sh.org> Reported-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Reviewed-by: Miguel Ojeda <ojeda@kernel.org> Signed-off-by: Rich Felker <dalias@libc.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dcr-low.S we use cmpli with three arguments, instead of four
arguments as defined in the ISA:
cmpli cr0,r3,1024
This appears to be a PPC440-ism, looking at the "PPC440x5 CPU Core
User’s Manual" it shows cmpli having no L field, but implied to be 0 due
to the core being 32-bit. It mentions that the ISA defines four
arguments and recommends using cmplwi.
It also corresponds to the old POWER instruction set, which had no L
field there, a reserved bit instead.
dcr-low.S is only built 32-bit, because it is only built when
DCR_NATIVE=y, which is only selected by 40x and 44x. Looking at the
generated code (with gcc/gas) we see cmplwi as expected.
Although gas is happy with the 3-argument version when building for
32-bit, the LLVM assembler is not and errors out with:
arch/powerpc/sysdev/dcr-low.S:27:10: error: invalid operand for instruction
cmpli 0,%r3,1024; ...
^
Switch to the cmplwi extended opcode, which avoids any confusion when
reading the ISA, fixes the issue with the LLVM assembler, and also means
the code could be built 64-bit in future (though that's very unlikely).
The pointer block return from snd_gf1_dma_next_block could be
null, so there is a potential null pointer dereference issue.
Fix this by adding a null check before dereference.
We can't free the tg_pt_gp in core_alua_set_tg_pt_gp_id() because it's
still accessed via configfs. Its release must go through the normal
configfs/refcount process.
The max alua_tg_pt_gps_count check should probably have been done in
core_alua_allocate_tg_pt_gp(), but with the current code userspace could
have created 0x0000ffff + 1 groups, but only set the id for 0x0000ffff.
Then it could have deleted a group with an ID set, and then set the ID for
that extra group and it would work ok.
It's unlikely, but just in case this patch continues to allow that type of
behavior, and just fixes the kfree() while in use bug.
projects / linux-stable / log