A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/power/reset/ltc2952-poweroff.c:162:28: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:162:21: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->wde_interval = 300L * 1E6L;
^
drivers/power/reset/ltc2952-poweroff.c:163:41: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
data->trigger_delay = ktime_set(2, 500L*1E6L);
^
3 errors generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for floating point values in this driver, as
the values are only assigned to integer types. Use NSEC_PER_MSEC, which
is the same integer value as '1E6L', to avoid changing functionality but
fix the error.
As we build for mips, we meet following error. l1_init error with
multiple definition. Some architecture devices usually marked with
l1, l2, lxx as the start-up phase. so we change the mISDN function
names, align with Isdnl2_xxx.
mips-linux-gnu-ld: drivers/isdn/mISDN/layer1.o: in function `l1_init':
(.text+0x890): multiple definition of `l1_init'; \
arch/mips/kernel/bmips_5xxx_init.o:(.text+0xf0): first defined here
make[1]: *** [home/mips/kernel-build/linux/Makefile:1161: vmlinux] Error 1
Signed-off-by: wolfgang huang <huangjinhui@kylinos.cn> Reported-by: k2ci <kernel-bot@kylinos.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "__ip6_tnl_parm" struct was left uninitialized causing an invalid
load of random data when the "__ip6_tnl_parm" struct was used elsewhere.
As an example, in the function "ip6_tnl_xmit_ctl()", it tries to access
the "collect_md" member. With "__ip6_tnl_parm" being uninitialized and
containing random data, the UBSAN detected that "collect_md" held a
non-boolean value.
The UBSAN issue is as follows:
===============================================================
UBSAN: invalid-load in net/ipv6/ip6_tunnel.c:1025:14
load of value 30 is not a valid value for type '_Bool'
CPU: 1 PID: 228 Comm: kworker/1:3 Not tainted 5.16.0-rc4+ #8
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x57
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value+0x66/0x70
? __cpuhp_setup_state+0x1d3/0x210
ip6_tnl_xmit_ctl.cold.52+0x2c/0x6f [ip6_tunnel]
vti6_tnl_xmit+0x79c/0x1e96 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? vti6_rcv+0x100/0x100 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? rcu_read_lock_bh_held+0xc0/0xc0
? lock_acquired+0x262/0xb10
dev_hard_start_xmit+0x1e6/0x820
__dev_queue_xmit+0x2079/0x3340
? mark_lock.part.52+0xf7/0x1050
? netdev_core_pick_tx+0x290/0x290
? kvm_clock_read+0x14/0x30
? kvm_sched_clock_read+0x5/0x10
? sched_clock_cpu+0x15/0x200
? find_held_lock+0x3a/0x1c0
? lock_release+0x42f/0xc90
? lock_downgrade+0x6b0/0x6b0
? mark_held_locks+0xb7/0x120
? neigh_connected_output+0x31f/0x470
? lockdep_hardirqs_on+0x79/0x100
? neigh_connected_output+0x31f/0x470
? ip6_finish_output2+0x9b0/0x1d90
? rcu_read_lock_bh_held+0x62/0xc0
? ip6_finish_output2+0x9b0/0x1d90
ip6_finish_output2+0x9b0/0x1d90
? ip6_append_data+0x330/0x330
? ip6_mtu+0x166/0x370
? __ip6_finish_output+0x1ad/0xfb0
? nf_hook_slow+0xa6/0x170
ip6_output+0x1fb/0x710
? nf_hook.constprop.32+0x317/0x430
? ip6_finish_output+0x180/0x180
? __ip6_finish_output+0xfb0/0xfb0
? lock_is_held_type+0xd9/0x130
ndisc_send_skb+0xb33/0x1590
? __sk_mem_raise_allocated+0x11cf/0x1560
? dst_output+0x4a0/0x4a0
? ndisc_send_rs+0x432/0x610
addrconf_dad_completed+0x30c/0xbb0
? addrconf_rs_timer+0x650/0x650
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
? addrconf_dad_completed+0xbb0/0xbb0
? rcu_read_lock_sched_held+0xaf/0xe0
? rcu_read_lock_bh_held+0xc0/0xc0
process_one_work+0x97b/0x1740
? pwq_dec_nr_in_flight+0x270/0x270
worker_thread+0x87/0xbf0
? process_one_work+0x1740/0x1740
kthread+0x3ac/0x490
? set_kthread_struct+0x100/0x100
ret_from_fork+0x22/0x30
</TASK>
===============================================================
The solution is to initialize "__ip6_tnl_parm" struct to zeros in the
"vti6_siocdevprivate()" function.
Signed-off-by: William Zhao <wizhao@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
__cpu_setup() configures SCTLR_EL1 using some hard coded hex masks,
and el2_setup() duplicates some this when setting RES1 bits.
Lets make this the same as KVM's hyp_init, which uses named bits.
First, we add definitions for all the SCTLR_EL{1,2} bits, the RES{1,0}
bits, and those we want to set or clear.
Add a build_bug checks to ensures all bits are either set or clear.
This means we don't need to preserve endian-ness configuration
generated elsewhere.
Finally, move the head.S and proc.S users of these hard-coded masks
over to the macro versions.
We only need to initialise sctlr_el1 if we're installing an EL2 stub, so
we may as well defer this until we're doing so. Similarly, we can defer
intialising CPTR_EL2 until then, as we do not access any trapped
functionality as part of el2_setup.
This patch modified el2_setup accordingly, allowing us to remove a
branch and simplify the code flow.
Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early el2_setup code is a little convoluted, with two branches where
one would do. This makes the code more painful to read than is
necessary.
We can remove a branch and simplify the logic by moving the early return
in the booted-at-EL1 case earlier in the function. This separates it
from all the setup logic that only makes sense for EL2.
Acked-by: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Including <linux/bug.h> pulls in a lot of bloat from <asm/bug.h> and
<asm-generic/bug.h> that is not needed to call the BUILD_BUG() family of
macros. Split them out into their own header, <linux/build_bug.h>.
Also correct some checkpatch.pl errors for the BUILD_BUG_ON_ZERO() and
BUILD_BUG_ON_NULL() macros by adding parentheses around the bitfield
widths that begin with a minus sign.
Link: http://lkml.kernel.org/r/20170525120316.24473-6-abbotti@mev.co.uk Signed-off-by: Ian Abbott <abbotti@mev.co.uk> Acked-by: Michal Nazarewicz <mina86@mina86.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jakub Kicinski <jakub.kicinski@netronome.com> Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[nathan: Just take this patch, not the checkpatch.pl patches before it] Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hytera makes a range of digital (DMR) radios. These radios can be
programmed to a allow a computer to control them over Ethernet over USB,
either using NCM or RNDIS.
This commit adds support for RNDIS for Hytera radios. I tested with a
Hytera PD785 and a Hytera MD785G. When these radios are programmed to
set up a Radio to PC Network using RNDIS, an USB interface will be added
with class 2 (Communications), subclass 2 (Abstract Modem Control) and
an interface protocol of 255 ("vendor specific" - lsusb even hints "MSFT
RNDIS?").
This patch is similar to the solution of this StackOverflow user, but
that only works for the Hytera MD785:
https://stackoverflow.com/a/53550858
To use the "Radio to PC Network" functionality of Hytera DMR radios, the
radios need to be programmed correctly in CPS (Hytera's Customer
Programming Software). "Forward to PC" should be checked in "Network"
(under "General Setting" in "Conventional") and the "USB Network
Communication Protocol" should be set to RNDIS.
Signed-off-by: Thomas Toye <thomas@toye.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old ALLOCSP/FREESP ioctls in XFS can be used to preallocate space at
the end of files, just like fallocate and RESVSP. Make the behavior
consistent with the other ioctls.
Reported-by: Kirill Tkhai <ktkhai@virtuozzo.com> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Reviewed-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Eric Sandeen <sandeen@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tx_queue_len can be set to ~0U, we need to be more
careful about overflows.
__fls(0) is undefined, as this report shows:
UBSAN: shift-out-of-bounds in net/sched/sch_qfq.c:1430:24
shift exponent 51770272 is too large for 32-bit type 'int'
CPU: 0 PID: 25574 Comm: syz-executor.0 Not tainted 5.16.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x201/0x2d8 lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:151 [inline]
__ubsan_handle_shift_out_of_bounds+0x494/0x530 lib/ubsan.c:330
qfq_init_qdisc+0x43f/0x450 net/sched/sch_qfq.c:1430
qdisc_create+0x895/0x1430 net/sched/sch_api.c:1253
tc_modify_qdisc+0x9d9/0x1e20 net/sched/sch_api.c:1660
rtnetlink_rcv_msg+0x934/0xe60 net/core/rtnetlink.c:5571
netlink_rcv_skb+0x200/0x470 net/netlink/af_netlink.c:2496
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x814/0x9f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0xaea/0xe60 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:704 [inline]
sock_sendmsg net/socket.c:724 [inline]
____sys_sendmsg+0x5b9/0x910 net/socket.c:2409
___sys_sendmsg net/socket.c:2463 [inline]
__sys_sendmsg+0x280/0x370 net/socket.c:2492
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x44/0xd0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 462dbc9101ac ("pkt_sched: QFQ Plus: fair-queueing service at DRR cost") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a wrong queues representation in sysfs during
driver's reinitialization in case of online cpus number is
less than combined queues. It was caused by stopped
NetworkManager, which is responsible for calling vsi_open
function during driver's initialization.
In specific situation (ex. 12 cpus online) there were 16 queues
in /sys/class/net/<iface>/queues. In case of modifying queues with
value higher, than number of online cpus, then it caused write
errors and other errors.
Add updating of sysfs's queues representation during driver
initialization.
Fixes: 41c445ff0f48 ("i40e: main driver core") Signed-off-by: Lukasz Cieplicki <lukaszx.cieplicki@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mlme.c:5332:7: warning: Branch condition evaluates to a
garbage value
have_higher_than_11mbit)
^~~~~~~~~~~~~~~~~~~~~~~
have_higher_than_11mbit is only set to true some of the time in
ieee80211_get_rates() but is checked all of the time. So
have_higher_than_11mbit needs to be initialized to false.
Fixes: 5d6a1b069b7f ("mac80211: set basic rates earlier") Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20211223162848.3243702-1-trix@redhat.com Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alexander reported a use of uninitialized value in
atusb_set_extended_addr(), that is caused by reading 0 bytes via
usb_control_msg().
Fix it by validating if the number of bytes transferred is actually
correct, since usb_control_msg() may read less bytes, than was requested
by caller.
Fail log:
BUG: KASAN: uninit-cmp in ieee802154_is_valid_extended_unicast_addr include/linux/ieee802154.h:310 [inline]
BUG: KASAN: uninit-cmp in atusb_set_extended_addr drivers/net/ieee802154/atusb.c:1000 [inline]
BUG: KASAN: uninit-cmp in atusb_probe.cold+0x29f/0x14db drivers/net/ieee802154/atusb.c:1056
Uninit value used in comparison: 311daa649a2003bd stack handle: 000000009a2003bd
ieee802154_is_valid_extended_unicast_addr include/linux/ieee802154.h:310 [inline]
atusb_set_extended_addr drivers/net/ieee802154/atusb.c:1000 [inline]
atusb_probe.cold+0x29f/0x14db drivers/net/ieee802154/atusb.c:1056
usb_probe_interface+0x314/0x7f0 drivers/usb/core/driver.c:396
Fixes: 7490b008d123 ("ieee802154: add support for atusb transceiver") Reported-by: Alexander Potapenko <glider@google.com> Acked-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Link: https://lore.kernel.org/r/20220104182806.7188-1-paskripkin@gmail.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a virtio pci device undergo surprise removal (aka async removal in
PCIe spec), mark the device as broken so that any upper layer drivers can
abort any outstanding operation.
When a virtio net pci device undergo surprise removal which is used by a
NetworkManager, a below call trace was observed.
osnoise tracer on ppc64le is triggering osnoise_taint() for negative
duration in get_int_safe_duration() called from
trace_sched_switch_callback()->thread_exit().
The problem though is that the check for a valid trace_percpu_buffer is
incorrect in get_trace_buf(). The check is being done after calculating
the pointer for the current cpu, rather than on the main percpu pointer.
Fix the check to be against trace_percpu_buffer.
In commit f44cb4b19ed4 ("Bluetooth: btusb: Fix quirk for Atheros
1525/QCA6174") we tried to address the non-working Atheros BT devices
by changing the quirk from BTUSB_ATH3012 to BTUSB_QCA_ROME. This made
such devices working while it turned out to break other existing chips
with the very same USB ID, hence it was reverted afterwards.
This is another attempt to tackle the issue. The essential point to
use BTUSB_QCA_ROME is to apply the btusb_setup_qca() and do RAM-
patching. And the previous attempt failed because btusb_setup_qca()
returns -ENODEV if the ROM version doesn't match with the expected
ones. For some devices that have already the "correct" ROM versions,
we may just skip the setup procedure and continue the rest.
So, the first fix we'll need is to add a check of the ROM version in
the function to skip the setup if the ROM version looks already sane,
so that it can be applied for all ath devices.
However, the world is a bit more complex than that simple solution.
Since BTUSB_ATH3012 quirk checks the bcdDevice and bails out when it's
0x0001 at the beginning of probing, so the device probe always aborts
here.
In this patch, we add another check of ROM version again, and if the
device needs patching, the probe continues. For that, a slight
refactoring of btusb_qca_send_vendor_req() was required so that the
probe function can pass usb_device pointer directly before allocating
hci_dev stuff.
This issue was also reported since 2017 in the thread [1],
unfortunately, the issue was still can be reproduced after fixing
DCCP.
The ipv4_mib_exit_net is called before tcp_sk_exit_batch when a net
namespace is destroyed since tcp_sk_ops is registered befrore
ipv4_mib_ops, which means tcp_sk_ops is in the front of ipv4_mib_ops
in the list of pernet_list. There will be a use-after-free on
net->mib.net_statistics in tw_timer_handler after ipv4_mib_exit_net
if there are some inflight time-wait timers.
This bug is not introduced by commit f2bf415cfed7 ("mib: add net to
NET_ADD_STATS_BH") since the net_statistics is a global variable
instead of dynamic allocation and freeing. Actually, commit 61a7e26028b9 ("mib: put net statistics on struct net") introduces
the bug since it put net statistics on struct net and free it when
net namespace is destroyed.
Moving init_ipv4_mibs() to the front of tcp_init() to fix this bug
and replace pr_crit() with panic() since continuing is meaningless
when init_ipv4_mibs() fails.
The spaceball.c module was not properly parsing the movement reports
coming from the device. The code read axis data as signed 16-bit
little-endian values starting at offset 2.
In fact, axis data in Spaceball movement reports are signed 16-bit
big-endian values starting at offset 3. This was determined first by
visually inspecting the data packets, and later verified by consulting:
http://spacemice.org/pdf/SpaceBall_2003-3003_Protocol.pdf
If this ever worked properly, it was in the time before Git...
Signed-off-by: Leo L. Schwab <ewhac@ewhac.org> Link: https://lore.kernel.org/r/20211221101630.1146385-1-ewhac@ewhac.org Cc: stable@vger.kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot has reported warning in __flush_work(). This warning is caused by
work->func == NULL, which means missing work initialization.
This may happen, since input_dev->close() calls
cancel_work_sync(&dev->work), but dev->work initalization happens _after_
input_register_device() call.
So this patch moves dev->work initialization before registering input
device
The PVSCSI implementation in the VMware hypervisor under specific
configuration ("SCSI Bus Sharing" set to "Physical") returns zero dataLen
in the completion descriptor for READ CAPACITY(16). As a result, the kernel
can not detect proper disk geometry. This can be recognized by the kernel
message:
The PVSCSI implementation in QEMU does not set dataLen at all, keeping it
zeroed. This leads to a boot hang as was reported by Shmulik Ladkani.
It is likely that the controller returns the garbage at the end of the
buffer. Residual length should be set by the driver in that case. The SCSI
layer will erase corresponding data. See commit bdb2b8cab439 ("[SCSI] erase
invalid data returned by device") for details.
Commit e662502b3a78 ("scsi: vmw_pvscsi: Set correct residual data length")
introduced the issue by setting residual length unconditionally, causing
the SCSI layer to erase the useful payload beyond dataLen when this value
is returned as 0.
As a result, considering existing issues in implementations of PVSCSI
controllers, we do not want to call scsi_set_resid() when dataLen ==
0. Calling scsi_set_resid() has no effect if dataLen equals buffer length.
Link: https://lore.kernel.org/lkml/20210824120028.30d9c071@blondie/ Link: https://lore.kernel.org/r/20211220190514.55935-1-amakhalov@vmware.com Fixes: e662502b3a78 ("scsi: vmw_pvscsi: Set correct residual data length") Cc: Matt Wang <wwentao@vmware.com> Cc: Martin K. Petersen <martin.petersen@oracle.com> Cc: Vishal Bhakta <vbhakta@vmware.com> Cc: VMware PV-Drivers <pv-drivers@vmware.com> Cc: James E.J. Bottomley <jejb@linux.ibm.com> Cc: linux-scsi@vger.kernel.org Cc: stable@vger.kernel.org Reported-and-suggested-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: Alexey Makhalov <amakhalov@vmware.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ffs_data_clear is indirectly called from both ffs_fs_kill_sb and
ffs_ep0_release, so it ends up being called twice when userland closes ep0
and then unmounts f_fs.
If userland provided an eventfd along with function's USB descriptors, it
ends up calling eventfd_ctx_put as many times, causing a refcount
underflow.
NULL-ify ffs_eventfd to prevent these extraneous eventfd_ctx_put calls.
Also, set epfiles to NULL right after de-allocating it, for readability.
For completeness, ffs_data_clear actually ends up being called thrice, the
last call being before the whole ffs structure gets freed, so when this
specific sequence happens there is a second underflow happening (but not
being reported):
The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.
BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk
Original patch went to stable so this should go there as well.
Fixes: ea0f69d82119 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller") Cc: stable@vger.kernel.org
cc: Nikolay Martynov <mar.kolya@gmail.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace sa_family_t with __kernel_sa_family_t to fix the following
linux/nfc.h userspace compilation errors:
/usr/include/linux/nfc.h:266:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
/usr/include/linux/nfc.h:274:2: error: unknown type name 'sa_family_t'
sa_family_t sa_family;
Fixes: 23b7869c0fd0 ("NFC: add the NFC socket raw protocol") Fixes: d646960f7986 ("NFC: Initial LLCP support") Cc: <stable@vger.kernel.org> Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reference taken by 'of_find_device_by_node()' must be released when
not needed anymore.
Add the corresponding 'put_device()' in the and error handling paths.
Fixes: 18a6c85fcc78 ("fsl/fman: Add FMan Port Support") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
hooks.c:5765:6: warning: 4th function call argument is an uninitialized
value
if (selinux_xfrm_postroute_last(sksec->sid, skb, &ad, proto))
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
selinux_parse_skb() can return ok without setting proto. The later call
to selinux_xfrm_postroute_last() does an early check of proto and can
return ok if the garbage proto value matches. So initialize proto.
Cc: stable@vger.kernel.org Fixes: eef9b41622f2 ("selinux: cleanup selinux_xfrm_sock_rcv_skb() and selinux_xfrm_postroute_last()") Signed-off-by: Tom Rix <trix@redhat.com>
[PM: typo/spelling and checkpatch.pl description fixes] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 85bf17b28f97 ("recordmcount.pl: look for jgnop instruction as well
as bcrl on s390") added a new alternative mnemonic for the existing brcl
instruction. This is required for the combination old gcc version (pre 9.0)
and binutils since version 2.37.
However at the same time this commit introduced a typo, replacing brcl with
bcrl. As a result no mcount locations are detected anymore with old gcc
versions (pre 9.0) and binutils before version 2.37.
Fix this by using the correct mnemonic again.
Reported-by: Miroslav Benes <mbenes@suse.cz> Cc: Jerome Marchand <jmarchan@redhat.com> Cc: <stable@vger.kernel.org> Fixes: 85bf17b28f97 ("recordmcount.pl: look for jgnop instruction as well as bcrl on s390") Link: https://lore.kernel.org/r/alpine.LSU.2.21.2112230949520.19849@pobox.suse.cz Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 4bc43a421218 ("HID: asus: Add
hid_is_using_ll_driver(usb_hid_driver) check") the hid-asus.c depends
on the usb_hid_driver symbol. Add a depends on USB_HID to Kconfig to
fix missing symbols errors in hid-asus when USB_HID is not enabled.
Fixes: 4bc43a421218 ("HID: asus: Add hid_is_using_ll_driver(usb_hid_driver) check") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Cc: Jason Self <jason@bluehome.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This ioctl() implicitly assumed that the socket was already bound to
a valid local socket name, i.e. Phonet object. If the socket was not
bound, two separate problems would occur:
1) We'd send an pipe enablement request with an invalid source object.
2) Later socket calls could BUG on the socket unexpectedly being
connected yet not bound to a valid object.
Reported-by: syzbot+2dc91e7fc3dea88b1e8a@syzkaller.appspotmail.com Signed-off-by: Rémi Denis-Courmont <remi@remlab.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous commit 3e0588c291d6 ("hamradio: defer ax25 kfree after
unregister_netdev") reorder the kfree operations and unregister_netdev
operation to prevent UAF.
This commit improves the previous one by also deferring the nullify of
the ax->tty pointer. Otherwise, a NULL pointer dereference bug occurs.
Partial of the stack trace is shown below.
By placing the nullify action after the unregister_netdev, the ax->tty
pointer won't be assigned as NULL net_device framework layer is well
synchronized.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though there are two synchronization primitives before the kfree:
1. wait_for_completion(&ax->dead). This can prevent the race with
routines from mkiss_ioctl. However, it cannot stop the routine coming
from upper layer, i.e., the ax25_sendmsg.
2. netif_stop_queue(ax->dev). It seems that this line of code aims to
halt the transmit queue but it fails to stop the routine that already
being xmit.
This patch reorder the kfree after the unregister_netdev to avoid the
possible UAF as the unregister_netdev() is well synchronized and won't
return if there is a running routine.
Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Other syscall functions like ax25_getsockopt, ax25_getname,
ax25_info_show also suffer from similar races. To fix them, this patch
introduce lock_sock() into ax25_kill_by_device in order to guarantee
that the nullify action in cleanup routine cannot proceed when another
socket request is pending.
Signed-off-by: Hanjie Wu <nagi@zju.edu.cn> Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bit 7 of the status register indicates that the chip is busy
doing a conversion. It does not indicate an alarm status.
Stop reporting it as alarm status bit.
The Thumb2 version of the FP exception handling entry code treats the
register holding the CP number (R8) differently, resulting in the iWMMXT
CP number check to be incorrect.
Fix this by unifying the ARM and Thumb2 code paths, and switch the
order of the additions of the TI_USED_CP offset and the shifted CP
index.
Cc: <stable@vger.kernel.org> Fixes: b86040a59feb ("Thumb-2: Implementation of the unified start-up and exceptions code") Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Static analysis with scan-build has found an assignment to vp2 that is
never used. It seems that the check on vp->state > 0 should be actually
on vp2->state instead. Fix this.
This dates back to 2002, I found the offending commit from the git
history git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git,
commit 91e39521bbf6 ("[PATCH] ALSA patch for 2.5.4")
The detect function had a comment "Make compiler happy" when id did not
read the second configuration register. As it turns out, the code was
checking the contents of this register for manufacturer ID 0xA1 (NXP
Semiconductor/Philips), but never actually read the register. So it
wasn't surprising that the compiler complained, and it indeed had a point.
Fix the code to read the register contents for manufacturer ID 0xa1.
At the same time, the code was reading the register for manufacturer ID
0x41 (Analog Devices), but it was not using the results. In effect it was
just checking if reading the register returned an error. That doesn't
really add much if any value, so stop doing that.
I find that platform_get_irq() will not always succeed.
It will return error irq in case of the failure.
Therefore, it might be better to check it if order to avoid the use of
error irq.
Fixes: 658d439b2292 ("fjes: Introduce FUJITSU Extended Socket Network Device driver") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When 802.3ad bond mode is configured the ad_actor_system option is set to
"00:00:00:00:00:00". But when trying to set the all-zeroes MAC as actors'
system address it was failing with EINVAL.
An all-zeroes ethernet address is valid, only multicast addresses are not
valid values.
Fixes: 171a42c38c6e ("bonding: add netlink support for sys prio, actor sys mac, and port key") Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Link: https://lore.kernel.org/r/20211221111345.2462-1-ffmancera@riseup.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The return value of kcalloc() needs to be checked.
To avoid dereference of null pointer in case of the failure of alloc.
Therefore, it might be better to change the return type of
qlcnic_sriov_alloc_vlans() and return -ENOMEM when alloc fails and
return 0 the others.
Also, qlcnic_sriov_set_guest_vlan_mode() and __qlcnic_pci_sriov_enable()
should deal with the return value of qlcnic_sriov_alloc_vlans().
Fixes: 154d0c810c53 ("qlcnic: VLAN enhancement for 84XX adapters") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The CAN clock frequency is used when calculating the CAN bittiming
parameters. When wrong clock frequency is used, the device may end up
with wrong bittiming parameters, depending on user requested bittiming
parameters.
To avoid this, get the CAN clock frequency from the device. Various
existing Kvaser Leaf products use different CAN clocks.
Fixes: 080f40a6fa28 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices") Link: https://lore.kernel.org/all/20211208152122.250852-2-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by: Jimmy Assarsson <extja@kvaser.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case a guest isn't consuming incoming network traffic as fast as it
is coming in, xen-netback is buffering network packages in unlimited
numbers today. This can result in host OOM situations.
Commit f48da8b14d04ca8 ("xen-netback: fix unlimited guest Rx internal
queue and carrier flapping") meant to introduce a mechanism to limit
the amount of buffered data by stopping the Tx queue when reaching the
data limit, but this doesn't work for cases like UDP.
When hitting the limit don't queue further SKBs, but drop them instead.
In order to be able to tell Rx packages have been dropped increment the
rx_dropped statistics counter in this case.
It should be noted that the old solution to continue queueing SKBs had
the additional problem of an overflow of the 32-bit rx_queue_len value
would result in intermittent Tx queue enabling.
Commit 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when
not using GSO") introduced a security problem in netback, as an
interface would only be regarded to be stalled if no slot is available
in the rx queue ring page. In case the SKB at the head of the queued
requests will need more than one rx slot and only one slot is free the
stall detection logic will never trigger, as the test for that is only
looking for at least one slot to be free.
Fix that by testing for the needed number of slots instead of only one
slot being available.
In order to not have to take the rx queue lock that often, store the
number of needed slots in the queue data. As all SKB dequeue operations
happen in the rx queue kernel thread this is safe, as long as the
number of needed slots is accessed via READ/WRITE_ONCE() only and
updates are always done with the rx queue lock held.
Add a small helper for obtaining the number of free slots.
This is part of XSA-392
Fixes: 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when not using GSO") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Xen console driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using a lateeoi event
channel.
For the normal domU initial console this requires the introduction of
bind_evtchn_to_irq_lateeoi() as there is no xenbus device available
at the time the event channel is bound to the irq.
As the decision whether an interrupt was spurious or not requires to
test for bytes having been read from the backend, move sending the
event into the if statement, as sending an event without having found
any bytes to be read is making no sense at all.
The Xen netfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
For being able to detect the case of no rx responses being added while
the carrier is down a new lock is needed in order to update and test
rsp_cons and the number of seen unconsumed responses atomically.
The Xen blkfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
A new warning in clang points out a few places in this driver where a
bitwise OR is being used with boolean types:
drivers/input/touchscreen.c:81:17: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
data_present = touchscreen_get_prop_u32(dev, "touchscreen-min-x",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This use of a bitwise OR is intentional, as bitwise operations do not
short circuit, which allows all the calls to touchscreen_get_prop_u32()
to happen so that the last parameter is initialized while coalescing the
results of the calls to make a decision after they are all evaluated.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each touchscreen_get_prop_u32() call to data_present,
which keeps the meaning of the code the same but makes it obvious that
every one of these calls is expected to happen.
Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reported-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Link: https://lore.kernel.org/r/20211014205757.3474635-1-nathan@kernel.org Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new warning in clang points out when macro expansion might result in a
GNU C statement expression. There is an instance of this in the mwifiex
driver:
drivers/net/wireless/marvell/mwifiex/cmdevt.c:217:34: warning: '}' and
')' tokens terminating statement expression appear in different macro
expansion contexts [-Wcompound-token-split-by-macro]
host_cmd->seq_num = cpu_to_le16(HostCmd_SET_SEQ_NO_BSS_INFO
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/fw.h:519:46: note: expanded from
macro 'HostCmd_SET_SEQ_NO_BSS_INFO'
(((type) & 0x000f) << 12); }
^
This does not appear to be a real issue. Removing the braces and
replacing them with parentheses will fix the warning and not change the
meaning of the code.
Fixes: 5e6e3a92b9a4 ("wireless: mwifiex: initial commit for Marvell mwifiex driver") Link: https://github.com/ClangBuiltLinux/linux/issues/1146 Reported-by: Andy Lavr <andy.lavr@gmail.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200901070834.1015754-1-natechancellor@gmail.com Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The naked attribute is known to confuse some old gcc versions when
function arguments aren't explicitly listed as inline assembly operands
despite the gcc documentation. That resulted in commit 9a40ac86152c
("ARM: 6164/1: Add kto and kfrom to input operands list.").
Yet that commit has problems of its own by having assembly operand
constraints completely wrong. If the generated code has been OK since
then, it is due to luck rather than correctness. So this patch also
provides proper assembly operand constraints, and removes two instances
of redundant register usages in the implementation while at it.
Inspection of the generated code with this patch doesn't show any
obvious quality degradation either, so not relying on __naked at all
will make the code less fragile, and avoid some issues with clang.
The only remaining __naked instances (excluding the kprobes test cases)
are exynos_pm_power_up_setup(), tc2_pm_power_up_setup() and
cci_enable_port_for_self(. But in the first two cases, only the function
address is used by the compiler with no chance of inlining it by
mistake, and the third case is called from assembly code only. And the
fact that no stack is available when the corresponding code is executed
does warrant the __naked usage in those cases.
Signed-off-by: Nicolas Pitre <nico@linaro.org> Reviewed-by: Stefan Agner <stefan@agner.ch> Tested-by: Stefan Agner <stefan@agner.ch> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang warns when a variable is assigned to itself.
drivers/net/usb/lan78xx.c:940:11: warning: explicitly assigning value of
variable of type 'u32' (aka 'unsigned int') to itself [-Wself-assign]
offset = offset;
~~~~~~ ^ ~~~~~~
1 warning generated.
Reorder the if statement to acheive the same result and avoid a self
assignment warning.
Link: https://github.com/ClangBuiltLinux/linux/issues/129 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Anders Roxell <anders.roxell@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In resp_mode_select() sanity check the block descriptor len to avoid UAF.
BUG: KASAN: use-after-free in resp_mode_select+0xa4c/0xb40 drivers/scsi/scsi_debug.c:2509
Read of size 1 at addr ffff888026670f50 by task scsicmd/15032
Without the bound checks for scpi_pd->name, it could result in the buffer
overflow when copying the SCPI device name from the corresponding device
tree node as the name string is set at maximum size of 30.
Let us fix it by using devm_kasprintf so that the string buffer is
allocated dynamically.
Fixes: 8bec4337ad40 ("firmware: scpi: add device power domain support using genpd") Reported-by: Pedro Batista <pedbap.g@gmail.com> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com> Cc: stable@vger.kernel.org Cc: Cristian Marussi <cristian.marussi@arm.com> Link: https://lore.kernel.org/r/20211209120456.696879-1-sudeep.holla@arm.com' Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
Even after commit e1d7ba873555 ("time: Always make sure wall_to_monotonic
isn't positive") it is still possible to make wall_to_monotonic positive
by running the following code:
The reason is that the second parameter of timespec64_compare(), ts_delta,
may be unnormalized because the delta is calculated with an open coded
substraction which causes the comparison of tv_sec to yield the wrong
result:
PCI_MSIX_FLAGS_MASKALL is set in the MSI-X control register at MSI-X
interrupt setup time. It's cleared on success, but the error handling path
only clears the PCI_MSIX_FLAGS_ENABLE bit.
That's incorrect as the reset state of the PCI_MSIX_FLAGS_MASKALL bit is
zero. That can be observed via lspci:
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db7272798 ("ixgbe: Introduce function to control MDIO speed") Signed-off-by: Cyril Novikov <cnovikov@lynx.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
Fixes: d4e0fe01a38a0 (igbvf: add new driver to support 82576 virtual functions) Reported-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Letu Ren <fantasquex@gmail.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not.
In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.
Fixes: 25cd5a391478 ("ARM: tegra: Add speedo-based process identification") Link: https://github.com/ClangBuiltLinux/linux/issues/1488 Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A delegation break could arrive as soon as we've called vfs_setlease. A
delegation break runs a callback which immediately (in
nfsd4_cb_recall_prepare) adds the delegation to del_recall_lru. If we
then exit nfs4_set_delegation without hashing the delegation, it will be
freed as soon as the callback is done with it, without ever being
removed from del_recall_lru.
Symptoms show up later as use-after-free or list corruption warnings,
usually in the laundromat thread.
I suspect aba2072f4523 "nfsd: grant read delegations to clients holding
writes" made this bug easier to hit, but I looked as far back as v3.0
and it looks to me it already had the same problem. So I'm not sure
where the bug was introduced; it may have been there from the beginning.
Cc: stable@vger.kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[Salvatore Bonaccorso: Backport for context changes to versions which do
not have 20b7d86f29d3 ("nfsd: use boottime for lease expiry calculation")] Signed-off-by: Salvatore Bonaccorso <carnil@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On s390, recordmcount.pl is looking for "bcrl 0,<xxx>" instructions in
the objdump -d outpout. However since binutils 2.37, objdump -d
display "jgnop <xxx>" for the same instruction. Update the
mcount_regex so that it accepts both.
Sending them out on a different queue can cause a race condition where a
number of packets in the queue may be discarded by the receiver, because
the ADDBA request is sent too early.
This affects any driver with software A-MPDU setup which does not allocate
packet seqno in hardware on tx, regardless of whether iTXQ is used or not.
The only driver I've seen that explicitly deals with this issue internally
is mwl8k.
Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau <nbd@nbd.name> Link: https://lore.kernel.org/r/20211202124533.80388-1-nbd@nbd.name Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The removal function is called regardless of whether
/proc/i8k was created successfully or not, the later
causing a WARN() on module removal.
Fix that by only registering the removal function
if /proc/i8k was created successfully.
Tested on a Inspiron 3505.
Fixes: 039ae58503f3 ("hwmon: Allow to compile dell-smm-hwmon driver without /proc/i8k") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Acked-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20211112171440.59006-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reason is elts->pages[i] is alloced by get_zeroed_page.
and kmemleak will not scan the area alloced by get_zeroed_page.
The address stored in elts->pages will be regarded as leaked.
That is, the elts->pages[i] will have pointers loaded onto it as well, and
without telling kmemleak about it, those pointers will look like memory
without a reference.
To fix this, call kmemleak_alloc to tell kmemleak to scan elts->pages[i]
Adding a check on len parameter to avoid empty skb. This prevents a
division error in netem_enqueue function which is caused when skb->len=0
and skb->data_len=0 in the randomized corruption step as shown below.
When link modes were initially added in commit 2c762679435dc
("net/mlx4_en: Use PTYS register to query ethtool settings") and
later updated for the new ethtool API in commit 3d8f7cc78d0eb
("net: mlx4: use new ETHTOOL_G/SSETTINGS API") the only 1/10G non-baseT
link modes configured were 1000baseKX, 10000baseKX4 and 10000baseKR.
It looks like these got picked to represent other modes since nothing
better was available.
Switch to using more specific link modes added in commit 5711a98221443
("net: ethtool: add support for 1000BaseX and missing 10G link modes").
Tested with MCX311A-XCAT connected via DAC.
Before:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseKX/Full
10000baseKR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseKX/Full
10000baseKR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
With this change:
% sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: 1000baseX/Full
10000baseCR/Full
10000baseSR/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Auto-negotiation: off
Port: Direct Attach Copper
PHYAD: 0
Transceiver: internal
Supports Wake-on: d
Wake-on: d
Current message level: 0x00000014 (20)
link ifdown
Link detected: yes
Tested-by: Michael Stapelberg <michael@stapelberg.ch> Signed-off-by: Erik Ekman <erik@kryo.se> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to ARM(v7M) ARM Interrupt Priority Offsets located at
0xE000E400-0xE000E5EC, while 0xE000E300-0xE000E33C covers read-only
Interrupt Active Bit Registers
Fixes: 292ec080491d ("irqchip: Add support for ARMv7-M NVIC") Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20211201110259.84857-1-vladimir.murzin@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
INVALL CMD specifies that the ITS must ensure any caching associated with
the interrupt collection defined by ICID is consistent with the LPI
configuration tables held in memory for all Redistributors. SYNC is
required to ensure that INVALL is executed.
Currently, LPI configuration data may be inconsistent with that in the
memory within a short period of time after the INVALL command is executed.
Signed-off-by: Wudi Wang <wangwudi@hisilicon.com> Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Fixes: cc2d3216f53c ("irqchip: GICv3: ITS command queue") Link: https://lore.kernel.org/r/20211208015429.5007-1-zhangshaokun@hisilicon.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irq-armada-370-xp driver already sets MSI_FLAG_MULTI_PCI_MSI flag into
msi_domain_info structure. But allocated interrupt numbers for Multi-MSI
needs to be properly aligned otherwise devices send MSI interrupt with
wrong number.
Fix this issue by using function bitmap_find_free_region() instead of
bitmap_find_next_zero_area() to allocate aligned interrupt numbers.
When ACPI type is ACPI_SMO8500, the data->dready_trig will not be set, the
memory allocated by iio_triggered_buffer_setup() will not be freed, and cause
memory leak as follows:
Fix it by remove data->dready_trig condition in probe and remove.
Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: a25691c1f967 ("iio: accel: kxcjk1013: allow using an external trigger") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Cc: <Stable@vger.kernel.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20211025124159.2700301-1-yangyingliang@huawei.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The itg3200 driver neglects to call iio_trigger_notify_done() when there is
an error reading the gyro data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The kxsd9 interrupt handler returns an error code if reading the data
registers fails. In addition when exiting due to an error the trigger
handler does not call `iio_trigger_notify_done()`. Which when not done
keeps the triggered disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
Since we can't return the error code make sure to at least log it as part
of the error message.
IIO trigger handlers need to return one of the irqreturn_t values.
Returning an error code is not supported.
The ltr501 interrupt handler gets this right for most error paths, but
there is one case where it returns the error code.
In addition for this particular case the trigger handler does not call
`iio_trigger_notify_done()`. Which when not done keeps the triggered
disabled forever.
Modify the code so that the function returns a valid irqreturn_t value as
well as calling `iio_trigger_notify_done()` on all exit paths.
The mma8452 driver directly assigns a trigger to the struct iio_dev. The
IIO core when done using this trigger will call `iio_trigger_put()` to drop
the reference count by 1.
Without the matching `iio_trigger_get()` in the driver the reference count
can reach 0 too early, the trigger gets freed while still in use and a
use-after-free occurs.
Fix this by getting a reference to the trigger before assigning it to the
IIO device.
Fixes: ae6d9ce05691 ("iio: mma8452: Add support for interrupt driven triggers.") Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Link: https://lore.kernel.org/r/20211024092700.6844-1-lars@metafoo.de Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The checks performed by commit aed9d65ac327 ("USB: validate
wMaxPacketValue entries in endpoint descriptors") require that initial
value of the maxp variable contains both maximum packet size bits
(10..0) and multiple-transactions bits (12..11). However, the existing
code assings only the maximum packet size bits. This patch assigns all
bits of wMaxPacketSize to the variable.
Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors") Cc: stable <stable@vger.kernel.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com> Link: https://lore.kernel.org/r/20211210085219.16796-1-pavel.hofman@ivitera.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log