Commit d208b89401e0 ("dm: fix mempool NULL pointer race when
completing IO") didn't go far enough.
When bio_end_io_acct ends the count of in-flight I/Os may reach zero
and the DM device may be suspended. There is a possibility that the
suspend races with dm_stats_account_io.
Fix this by adding percpu "pending_io" counters to track outstanding
dm_io. Move kicking of suspend queue to dm_io_dec_pending(). Also,
rename md_in_flight_bios() to dm_in_flight_bios() and update it to
iterate all pending_io counters.
dm_io_dec_pending() calls end_io_acct() first and will then dec md
in-flight pending count. But if a task is swapping DM table at same
time this can result in a crash due to mempool->elements being NULL:
Fix this by:
1) Establishing pointers to 'struct dm_io' members in
dm_io_dec_pending() so that they may be passed into end_io_acct()
_after_ free_io() is called.
2) Moving end_io_acct() after free_io().
Cc: stable@vger.kernel.org Signed-off-by: Jiazi Li <lijiazi@xiaomi.com> Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reviewed-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two reasons for addrconf_notify() to be called with NETDEV_DOWN:
either the network device is actually going down, or IPv6 was disabled
on the interface.
If either of them stays down while the other is toggled, we repeatedly
call the code for NETDEV_DOWN, including ipv6_mc_down(), while never
calling the corresponding ipv6_mc_up() in between. This will cause a
new entry in idev->mc_tomb to be allocated for each multicast group
the interface is subscribed to, which in turn leaks one struct ifmcaddr6
per nontrivial multicast group the interface is subscribed to.
The following reproducer will leak at least $n objects:
ip addr add ff2e::4242/32 dev eth0 autojoin
sysctl -w net.ipv6.conf.eth0.disable_ipv6=1
for i in $(seq 1 $n); do
ip link set up eth0; ip link set down eth0
done
Joining groups with IPV6_ADD_MEMBERSHIP (unprivileged) or setting the
sysctl net.ipv6.conf.eth0.forwarding to 1 (=> subscribing to ff02::2)
can also be used to create a nontrivial idev->mc_list, which will the
leak objects with the right up-down-sequence.
Based on both sources for NETDEV_DOWN events the interface IPv6 state
should be considered:
- not ready if the network interface is not ready OR IPv6 is disabled
for it
- ready if the network interface is ready AND IPv6 is enabled for it
The functions ipv6_mc_up() and ipv6_down() should only be run when this
state changes.
Implement this by remembering when the IPv6 state is ready, and only
run ipv6_mc_down() if it actually changed from ready to not ready.
The other direction (not ready -> ready) already works correctly, as:
- the interface notification triggered codepath for NETDEV_UP /
NETDEV_CHANGE returns early if ipv6 is disabled, and
- the disable_ipv6=0 triggered codepath skips fully initializing the
interface as long as addrconf_link_ready(dev) returns false
- calling ipv6_mc_up() repeatedly does not leak anything
Fixes: 3ce62a84d53c ("ipv6: exit early in addrconf_notify() if IPv6 is disabled") Signed-off-by: Johannes Nixdorf <j.nixdorf@avm.de> Signed-off-by: David S. Miller <davem@davemloft.net>
[jnixdorf: context updated for bpo to v4.9/v4.14] Signed-off-by: Johannes Nixdorf <j.nixdorf@avm.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
net: sched: prevent UAF on tc_ctl_tfilter when temporarily dropping rtnl_lock
When dropping the rtnl_lock for looking up for a module, the device may be
removed, releasing the qdisc and class memory. Right after trying to load
the module, cl_ops->put is called, leading to a potential use-after-free.
Though commit e368fdb61d8e ("net: sched: use Qdisc rcu API instead of
relying on rtnl lock") fixes this, it involves a lot of refactoring of the
net/sched/ code, complicating its backport.
This fix calls cl_ops->put before dropping rtnl_lock as it will be called
either way, and zeroes it out so it won't be called again on the exit path.
This has been shown to stop the following KASAN report with the reproducer:
On some x86 processors, CPUID leaf 0xA provides information
on Architectural Performance Monitoring features. It
advertises a PMU version which Qemu uses to determine the
availability of additional MSRs to manage the PMCs.
Upon receiving a KVM_GET_SUPPORTED_CPUID ioctl request for
the same, the kernel constructs return values based on the
x86_pmu_capability irrespective of the vendor.
This leaf and the additional MSRs are not supported on AMD
and Hygon processors. If AMD PerfMonV2 is detected, the PMU
version is set to 2 and guest startup breaks because of an
attempt to access a non-existent MSR. Return zeros to avoid
this.
Fixes: a6c06ed1a60a ("KVM: Expose the architectural performance monitoring CPUID leaf") Reported-by: Vasant Hegde <vasant.hegde@amd.com> Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Message-Id: <3fef83d9c2b2f7516e8ff50d60851f29a4bcb716.1651058600.git.sandipan.das@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Whenever RCU protected list replaces an object,
the pointer to the new object needs to be updated
_before_ the call to kfree_rcu() or call_rcu()
Because kfree_rcu(ptr, rcu) got support for NULL ptr
only recently in commit 12edff045bc6 ("rcu: Make kfree_rcu()
ignore NULL pointers"), I chose to use the conditional
to make sure stable backports won't miss this detail.
if (psl)
kfree_rcu(psl, rcu);
net/ipv6/mcast.c has similar issues, addressed in a separate patch.
[1]
BUG: KASAN: use-after-free in ip_mc_sf_allow+0x6bb/0x6d0 net/ipv4/igmp.c:2655
Read of size 4 at addr ffff88807d37b904 by task syz-executor.5/908
Second to last potentially related work creation:
kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
__kasan_record_aux_stack+0x7e/0x90 mm/kasan/generic.c:348
call_rcu+0x99/0x790 kernel/rcu/tree.c:3074
mpls_dev_notify+0x552/0x8a0 net/mpls/af_mpls.c:1656
notifier_call_chain+0xb5/0x200 kernel/notifier.c:84
call_netdevice_notifiers_info+0xb5/0x130 net/core/dev.c:1938
call_netdevice_notifiers_extack net/core/dev.c:1976 [inline]
call_netdevice_notifiers net/core/dev.c:1990 [inline]
unregister_netdevice_many+0x92e/0x1890 net/core/dev.c:10751
default_device_exit_batch+0x449/0x590 net/core/dev.c:11245
ops_exit_list+0x125/0x170 net/core/net_namespace.c:167
cleanup_net+0x4ea/0xb00 net/core/net_namespace.c:594
process_one_work+0x996/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e9/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298
The buggy address belongs to the object at ffff88807d37b900
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 4 bytes inside of
64-byte region [ffff88807d37b900, ffff88807d37b940)
Memory state around the buggy address: ffff88807d37b800: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc ffff88807d37b880: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc
>ffff88807d37b900: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^ ffff88807d37b980: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff88807d37ba00: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc
Fixes: c85bb41e9318 ("igmp: fix ip_mc_sf_allow race [v5]") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Flavio Leitner <fbl@sysclose.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Linux, empty symlinks are invalid, and attempting to create one with
the system call symlink(2) results in an -ENOENT error and this is
explicitly documented in the man page.
If we rename a symlink that was created in the current transaction and its
parent directory was logged before, we actually end up logging the symlink
without logging its content, which is stored in an inline extent. That
means that after a power failure we can end up with an empty symlink,
having no content and an i_size of 0 bytes.
It can be easily reproduced like this:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ mkdir /mnt/testdir
$ sync
# Create a file inside the directory and fsync the directory.
$ touch /mnt/testdir/foo
$ xfs_io -c "fsync" /mnt/testdir
# Create a symlink inside the directory and then rename the symlink.
$ ln -s /mnt/testdir/foo /mnt/testdir/bar
$ mv /mnt/testdir/bar /mnt/testdir/baz
# Now fsync again the directory, this persist the log tree.
$ xfs_io -c "fsync" /mnt/testdir
<power failure>
$ mount /dev/sdc /mnt
$ stat -c %s /mnt/testdir/baz
0
$ readlink /mnt/testdir/baz
$
Fix this by always logging symlinks in full mode (LOG_INODE_ALL), so that
their content is also logged.
A test case for fstests will follow.
CC: stable@vger.kernel.org # 4.9+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AlphaProject AP-SH4A-3A/AP-SH4AD-0A SH boards use IRQ0 for their SMSC
LAN911x Ethernet chip, so the networking on them must have been broken by
commit 965b2aa78fbc ("net/smsc911x: fix irq resource allocation failure")
which filtered out 0 as well as the negative error codes -- it was kinda
correct at the time, as platform_get_irq() could return 0 on of_irq_get()
failure and on the actual 0 in an IRQ resource. This issue was fixed by
me (back in 2016!), so we should be able to fix this driver to allow IRQ0
usage again...
When merging this to the stable kernels, make sure you also merge commit e330b9a6bb35 ("platform: don't return 0 from platform_get_irq[_byname]()
on error") -- that's my fix to platform_get_irq() for the DT platforms...
As pointed out by Sascha Hauer, this patch changes:
if (pmc->config && !pcm->config->prepare_slave_config)
<do nothing>
to:
if (pmc->config && !pcm->config->prepare_slave_config)
snd_dmaengine_pcm_prepare_slave_config()
This breaks the drivers that do not need a call to
dmaengine_slave_config(). Drivers that still need to call
snd_dmaengine_pcm_prepare_slave_config(), but have a NULL
pcm->config->prepare_slave_config should use
snd_dmaengine_pcm_prepare_slave_config() as their prepare_slave_config
callback.
Fixes: 9a1e13440a4f ("ASoC: dmaengine: do not use a NULL prepare_slave_config() callback") Reported-by: Sascha Hauer <sha@pengutronix.de> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20220421125403.2180824-1-codrin.ciubotariu@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When removing the adt7470 module, a warning might be printed:
do not call blocking ops when !TASK_RUNNING; state=1
set at [<ffffffffa006052b>] adt7470_update_thread+0x7b/0x130 [adt7470]
This happens because adt7470_update_thread() can leave the kthread in
TASK_INTERRUPTIBLE state when the kthread is being stopped before
the call of set_current_state(). Since kthread_exit() might sleep in
exit_signals(), the warning is printed.
Fix that by using schedule_timeout_interruptible() and removing
the call of set_current_state().
This causes TASK_INTERRUPTIBLE to be set after kthread_should_stop()
which might cause the kthread to exit.
Reported-by: Zheyu Ma <zheyuma97@gmail.com> Fixes: 93cacfd41f82 (hwmon: (adt7470) Allow faster removal) Signed-off-by: Armin Wolf <W_Armin@gmx.de> Tested-by: Zheyu Ma <zheyuma97@gmail.com> Link: https://lore.kernel.org/r/20220407101312.13331-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are sleep in atomic bug that could cause kernel panic during
firmware download process. The root cause is that nlmsg_new with
GFP_KERNEL parameter is called in fw_dnld_timeout which is a timer
handler. The call trace is shown below:
BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265
Call Trace:
kmem_cache_alloc_node
__alloc_skb
nfc_genl_fw_download_done
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
...
The nlmsg_new with GFP_KERNEL parameter may sleep during memory
allocation process, and the timer handler is run as the result of
a "software interrupt" that should not call any other function
that could sleep.
This patch changes allocation mode of netlink message from GFP_KERNEL
to GFP_ATOMIC in order to prevent sleep in atomic bug. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
There are destructive operations such as nfcmrvl_fw_dnld_abort and
gpio_free in nfcmrvl_nci_unregister_dev. The resources such as firmware,
gpio and so on could be destructed while the upper layer functions such as
nfcmrvl_fw_dnld_start and nfcmrvl_nci_recv_frame is executing, which leads
to double-free, use-after-free and null-ptr-deref bugs.
There are three situations that could lead to double-free bugs.
The firmware struct is deallocated in position (1) and deallocated
in position (2) again.
The crash trace triggered by POC is like below:
BUG: KASAN: double-free or invalid-free in fw_dnld_over
Call Trace:
kfree
fw_dnld_over
nfcmrvl_nci_unregister_dev
nci_uart_tty_close
tty_ldisc_kill
tty_ldisc_hangup
__tty_hangup.part.0
tty_release
...
What's more, there are also use-after-free and null-ptr-deref bugs
in nfcmrvl_fw_dnld_start. If we deallocate firmware struct, gpio or
set null to the members of priv->fw_dnld in nfcmrvl_nci_unregister_dev,
then, we dereference firmware, gpio or the members of priv->fw_dnld in
nfcmrvl_fw_dnld_start, the UAF or NPD bugs will happen.
This patch reorders destructive operations after nci_unregister_device
in order to synchronize between cleanup routine and firmware download
routine.
The nci_unregister_device is well synchronized. If the device is
detaching, the firmware download routine will goto error. If firmware
download routine is executing, nci_unregister_device will wait until
firmware download routine is finished.
Fixes: 3194c6870158 ("NFC: nfcmrvl: add firmware download support") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device_is_registered() in nfc core is used to check whether
nfc device is registered in netlink related functions such as
nfc_fw_download(), nfc_dev_up() and so on. Although device_is_registered()
is protected by device_lock, there is still a race condition between
device_del() and device_is_registered(). The root cause is that
kobject_del() in device_del() is not protected by device_lock.
The device_is_registered() returns the value of state_in_sysfs and
the state_in_sysfs is set to zero in kobject_del(). If we pass check in
position (1), then set zero in position (2). As a result, the check
in position (1) is useless.
This patch uses bool variable instead of device_is_registered() to judge
whether the nfc device is registered, which is well synchronized.
Fixes: 3e256b8f8dfa ("NFC: add nfc subsystem core") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are deadlocks caused by del_timer_sync(&priv->hang_timer) and
del_timer_sync(&priv->rr_timer) in grcan_close(), one of the deadlocks
are shown below:
We hold priv->lock in position (1) of thread 1 and use
del_timer_sync() to wait timer to stop, but timer handler also need
priv->lock in position (2) of thread 2. As a result, grcan_close()
will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain the
needed lock.
Link: https://lore.kernel.org/all/20220425042400.66517-1-duoming@zju.edu.cn Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores") Cc: stable@vger.kernel.org Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The WM8958 DSP controls all return 0 on successful write, not a boolean
value indicating if the write changed the value of the control. Fix this
by returning 1 after a change, there is already a check at the start of
each put() that skips the function in the case that there is no change.
card->local_node and card->bm_retries are both always accessed under
card->lock.
fw_core_handle_bus_reset has a check whose condition depends on
card->local_node and whose body writes to card->bm_retries.
Both of these accesses are not under card->lock. Move the lock acquiring
of card->lock to before this check such that these accesses do happen
when card->lock is held.
fw_destroy_nodes is called inside the check.
Since fw_destroy_nodes already acquires card->lock inside its function
body, move this out to the callsites of fw_destroy_nodes.
Also add a comment to indicate which locking is necessary when calling
fw_destroy_nodes.
When list_for_each_entry() completes the iteration over the whole list
without breaking the loop, the iterator value will be a bogus pointer
computed based on the head element.
While it is safe to use the pointer to determine if it was computed
based on the head element, either with list_entry_is_head() or
&pos->member == head, using the iterator variable after the loop should
be avoided.
In preparation to limit the scope of a list iterator to the list
traversal loop, use a dedicated pointer to point to the found element [1].
&e->event and e point to the same address, and &e->event could
be freed in queue_event. So there is a potential uaf issue if
we dereference e after calling queue_event(). Fix this by adding
a temporary variable to maintain e->client in advance, this can
avoid the potential uaf issue.
We must not try to connect the socket while the transport is under
construction, because the mechanisms to safely tear it down are not in
place. As the code stands, we end up leaking the sockets on a connection
error.
ALSA fireworks driver has a bug in its initial state to return count
shorter than expected by 4 bytes to userspace applications when handling
response frame for Echo Audio Fireworks transaction. It's due to missing
addition of the size for the type of event in ALSA firewire stack.
The Linux tool "lscpu" shows the double amount of CPUs if we have
"model" and "model name" in two different lines in /proc/cpuinfo.
This change combines the model and the model name into one line.
Fix the discrepancy between the two places we check for the CP0 counter
erratum in along with the incorrect comparison of the R4400 revision
number against 0x30 which matches none and consistently consider all
R4000 and R4400 processors affected, as documented in processor errata
publications[1][2][3], following the mapping between CP0 PRId register
values and processor models:
No other revision of either processor has ever been spotted.
Contrary to what has been stated in commit ce202cbb9e0b ("[MIPS] Assume
R4000/R4400 newer than 3.0 don't have the mfc0 count bug") marking the
CP0 counter as buggy does not preclude it from being used as either a
clock event or a clock source device. It just cannot be used as both at
a time, because in that case clock event interrupts will be occasionally
lost, and the use as a clock event device takes precedence.
Compare against 0x4ff in `can_use_mips_counter' so that a single machine
instruction is produced.
References:
[1] "MIPS R4000PC/SC Errata, Processor Revision 2.2 and 3.0", MIPS
Technologies Inc., May 10, 1994, Erratum 53, p.13
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: ce202cbb9e0b ("[MIPS] Assume R4000/R4400 newer than 3.0 don't have the mfc0 count bug") Cc: stable@vger.kernel.org # v2.6.24+ Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.4.2 states that any received unnumbered
acknowledgment (UA) with its poll/final (PF) bit set to 0 shall be
discarded. Currently, all UA frame are handled in the same way regardless
of the PF bit. This does not comply with the standard.
Remove the UA case in gsm_queue() to process only UA frames with PF bit set
to 1 to abide the standard.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.1 states that each command frame shall
be made up from type, length and value. Looking for example in chapter
5.4.6.3.5 at the description for the encoding of a flow control on command
it becomes obvious, that the type and length field is always present
whereas the value may be zero bytes long. The current implementation omits
the length field if the value is not present. This is wrong.
Correct this by always sending the length in gsm_control_transmit().
So far only the modem status command (MSC) has included a value and encoded
its length directly. Therefore, also change gsmtty_modem_update().
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.3 states that the valid range for the
maximum number of retransmissions (N2) is from 0 to 255 (both including).
gsm_config() fails to limit this range correctly. Furthermore,
gsm_control_retransmit() handles this number incorrectly by performing
N2 - 1 retransmission attempts. Setting N2 to zero results in more than 255
retransmission attempts.
Fix the range check in gsm_config() and the value handling in
gsm_control_send() and gsm_control_retransmit() to comply with 3GPP 27.010.
In gsm_cleanup_mux() the muxer is closed down and all queues are removed.
However, removing the queues is done without explicit control of the
underlying buffers. Flush those before freeing up our queues to ensure
that all outgoing queues are cleared consistently. Otherwise, a new mux
connection establishment attempt may time out while the underlying tty is
still busy sending out the remaining data from the previous connection.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.7.2 states that the maximum frame size
(N1) refers to the length of the information field (i.e. user payload).
However, 'txframe' stores the whole frame including frame header, checksum
and start/end flags. We also need to consider the byte stuffing overhead.
Define constant for the protocol overhead and adjust the 'txframe' size
calculation accordingly to reserve enough space for a complete mux frame
including byte stuffing for advanced option mode. Note that no byte
stuffing is applied to the start and end flag.
Also use MAX_MTU instead of MAX_MRU as this buffer is used for data
transmission.
The gsm_mux field 'malformed' represents the number of malformed frames
received. However, gsm1_receive() also increases this counter for any out
of frame byte.
Fix this by ignoring out of frame data for the malformed counter.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.5.2 describes that the signal octet in
convergence layer type 2 can be either one or two bytes. The length is
encoded in the EA bit. This is set 1 for the last byte in the sequence.
gsmtty_modem_update() handles this correctly but gsm_dlci_data_output()
fails to set EA to 1. There is no case in which we encode two signal octets
as there is no case in which we send out a break signal.
Therefore, always set the EA bit to 1 for the signal octet to fix this.
When resuming from system sleep state, restore_processor_state()
restores the boot CPU MSRs. These MSRs could be emulated by microcode.
If microcode is not loaded yet, writing to emulated MSRs leads to
unchecked MSR access error:
We hold rrpriv->lock in position (1) of thread 1 and
use del_timer_sync() to wait timer to stop, but timer handler
also need rrpriv->lock in position (2) of thread 2.
As a result, rr_close() will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain
the needed lock.
While handling PCI errors (AER flow) driver tries to
disable NAPI [napi_disable()] after NAPI is deleted
[__netif_napi_del()] which causes unexpected system
hang/crash.
EEH calls into bnx2x twice based on the system log above, first through
bnx2x_io_error_detected() and then bnx2x_io_slot_reset(), and executes
the following call chains:
This code is really spurious.
It always returns an ERR_PTR, even when err is known to be 0 and calls
put_device() after a successful device_register() call.
It is likely that the return statement in the normal path is missing.
Add 'return rdev;' to fix it.
Fixes: d787dcdb9c8f ("bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Samuel Holland <samuel@sholland.org> Tested-by: Samuel Holland <samuel@sholland.org> Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com> Link: https://lore.kernel.org/r/ef2b9576350bba4c8e05e669e9535e9e2a415763.1650551719.git.christophe.jaillet@wanadoo.fr Signed-off-by: Sasha Levin <sashal@kernel.org>
I had this bug sitting for too long in my pile, it is time to fix it.
Thanks to Doug Porter for reminding me of it!
We had various attempts in the past, including commit 0cbe6a8f089e ("tcp: remove SOCK_QUEUE_SHRUNK"),
but the issue is that TCP stack currently only generates
EPOLLOUT from input path, when tp->snd_una has advanced
and skb(s) cleaned from rtx queue.
If a flow has a big RTT, and/or receives SACKs, it is possible
that the notsent part (tp->write_seq - tp->snd_nxt) reaches 0
and no more data can be sent until tp->snd_una finally advances.
What is needed is to also check if POLLOUT needs to be generated
whenever tp->snd_nxt is advanced, from output path.
This bug triggers more often after an idle period, as
we do not receive ACK for at least one RTT. tcp_notsent_lowat
could be a fraction of what CWND and pacing rate would allow to
send during this RTT.
In a followup patch, I will remove the bogus call
to tcp_chrono_stop(sk, TCP_CHRONO_SNDBUF_LIMITED)
from tcp_check_space(). Fact that we have decided to generate
an EPOLLOUT does not mean the application has immediately
refilled the transmit queue. This optimistic call
might have been the reason the bug seemed not too serious.
Tested:
200 ms rtt, 1% packet loss, 32 MB tcp_rmem[2] and tcp_wmem[2]
$ echo 500000 >/proc/sys/net/ipv4/tcp_notsent_lowat
$ cat bench_rr.sh
SUM=0
for i in {1..10}
do
V=`netperf -H remote_host -l30 -t TCP_RR -- -r 10000000,10000 -o LOCAL_BYTES_SENT | egrep -v "MIGRATED|Bytes"`
echo $V
SUM=$(($SUM + $V))
done
echo SUM=$SUM
For GRE and GRETAP devices, currently o_seqno starts from 1 in native
mode. According to RFC 2890 2.2., "The first datagram is sent with a
sequence number of 0." Fix it.
It is worth mentioning that o_seqno already starts from 0 in collect_md
mode, see gre_fb_xmit(), where tunnel->o_seqno is passed to
gre_build_header() before getting incremented.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Commit a1ebdb374199 ("ARM: dts: Fix swapped mmc order for omap3")
introduces general mmc aliases. Let's tailor them to the need
of the GTA04 board which does not make use of mmc2 and mmc3 interfaces.
Fixes: a1ebdb374199 ("ARM: dts: Fix swapped mmc order for omap3") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Message-Id: <dc9173ee3d391d9e92b7ab8ed4f84b29f0a21c83.1646744420.git.hns@goldelico.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: fd1c07861491 ("ARM: OMAP4: Fix the init code to have OMAP4460 errata available in DT build") Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Message-Id: <20220309104302.18398-1-linmq006@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On a custom carrier board with a i.MX6Q Apalis SoM, the sgtl5000 codec
on the SoM is often not detected and the following error message is
seen when the sgtl5000 driver tries to read the ID register:
sgtl5000 1-000a: Error reading chip id -6
The reason for the error is that the MCLK clock is not provided
early enough.
Fix the problem by describing the MCLK pinctrl inside the codec
node instead of placing it inside the audmux pinctrl group.
With this change applied the sgtl5000 is always detected on every boot.
Fixes: 693e3ffaae5a ("ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM") Signed-off-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Tim Harvey <tharvey@gateworks.com> Acked-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we pass too short string to "hex2bin" (and the string size without
the terminating NUL character is even), "hex2bin" reads one byte after
the terminating NUL character. This patch fixes it.
Note that hex_to_bin returns -1 on error and hex2bin return -EINVAL on
error - so we can't just return the variable "hi" or "lo" on error.
This inconsistency may be fixed in the next merge window, but for the
purpose of fixing this bug, we just preserve the existing behavior and
return -1 and -EINVAL.
The function hex2bin is used to load cryptographic keys into device
mapper targets dm-crypt and dm-integrity. It should take constant time
independent on the processed data, so that concurrently running
unprivileged code can't infer any information about the keys via
microarchitectural convert channels.
This patch changes the function hex_to_bin so that it contains no
branches and no memory accesses.
Note that this shouldn't cause performance degradation because the size
of the new function is the same as the size of the old function (on
x86-64) - and the new function causes no branch misprediction penalties.
I compile-tested this function with gcc on aarch64 alpha arm hppa hppa64
i386 ia64 m68k mips32 mips64 powerpc powerpc64 riscv sh4 s390x sparc32
sparc64 x86_64 and with clang on aarch64 arm hexagon i386 mips32 mips64
powerpc powerpc64 s390x sparc32 sparc64 x86_64 to verify that there are
no branches in the generated code.
The EndRun PTP/1588 dual serial port device is based on the Oxford
Semiconductor OXPCIe952 UART device with the PCI vendor:device ID set
for EndRun Technologies and is therefore driven by a fixed 62.5MHz clock
input derived from the 100MHz PCI Express clock. The clock rate is
divided by the oversampling rate of 16 as it is supplied to the baud
rate generator, yielding the baud base of 3906250.
Replace the incorrect baud base of 4000000 with the right value of 3906250 then, complementing commit 6cbe45d8ac93 ("serial: 8250: Correct
the clock for OxSemi PCIe devices").
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Cc: stable <stable@kernel.org> Fixes: 1bc8cde46a159 ("8250_pci: Added driver for Endrun Technologies PTP PCIe card.") Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181515270.9383@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sticky MCR bits are lost in console restoration if console suspending
has been disabled. This currently affects the AFE bit, which works in
combination with RTS which we set, so we want to make sure the UART
retains control of its FIFO where previously requested. Also specific
drivers may need other bits in the future.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Fixes: 4516d50aabed ("serial: 8250: Use canary to restart console after suspend") Cc: stable@vger.kernel.org # v4.0+ Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204181518490.9383@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If any function like UVC is deactivating gadget as part of composition
switch which results in not calling pullup enablement, it is not getting
enabled after switch to new composition due to this deactivation flag
not cleared. This results in USB enumeration not happening after switch
to new USB composition. Hence clear deactivation flag inside gadget
structure in configfs_composite_unbind() before switch to new USB
composition.
During the uvcg_video_pump() process, if an error occurs and
uvcg_queue_cancel() is called, the buffer queue will be cleared out, but
the current marker (queue->buf_used) of the active buffer (no longer
active) is not reset. On the next iteration of uvcg_video_pump() the
stale buf_used count will be used and the logic of min((unsigned
int)len, buf->bytesused - queue->buf_used) may incorrectly calculate a
nbytes size, causing an invalid memory access.
[80802.185460][ T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
[80802.185519][ T315] configfs-gadget gadget: uvc: VS request completed
with status -18.
...
uvcg_queue_cancel() is called and the queue is cleared out, but the
marker queue->buf_used is not reset.
...
[80802.262328][ T8682] Unable to handle kernel paging request at virtual
address ffffffc03af9f000
...
...
[80802.263138][ T8682] Call trace:
[80802.263146][ T8682] __memcpy+0x12c/0x180
[80802.263155][ T8682] uvcg_video_pump+0xcc/0x1e0
[80802.263165][ T8682] process_one_work+0x2cc/0x568
[80802.263173][ T8682] worker_thread+0x28c/0x518
[80802.263181][ T8682] kthread+0x160/0x170
[80802.263188][ T8682] ret_from_fork+0x10/0x18
[80802.263198][ T8682] Code: a8c12829a88130cb a8c130
Fixes: d692522577c0 ("usb: gadget/uvc: Port UVC webcam gadget to use videobuf2 framework") Cc: <stable@vger.kernel.org> Signed-off-by: Dan Vacura <w36195@motorola.com> Link: https://lore.kernel.org/r/20220331184024.23918-1-w36195@motorola.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_put_dev shouldn't be called when uss720_probe succeeds because of
priv->usbdev. At the same time, priv->usbdev shouldn't be set to NULL
before destroy_priv in uss720_disconnect because usb_put_dev is in
destroy_priv.
Fix this by moving priv->usbdev = NULL after usb_put_dev.
While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.
Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.
[check shared hcd exist before stopping its roothub polling -Mathias]
The result is technically harmless, as both the source and the
destinations are currently the same allocation size (4 bytes) and don't
use their padding, but if anything were to ever be added after the
"mcr" member in "struct whiteheat_private", it would be overwritten. The
structs both have a single u8 "mcr" member, but are 4 bytes in padded
size. The memcpy() destination was explicitly targeting the u8 member
(size 1) with the length of the whole structure (size 4), triggering
the memcpy buffer overflow warning:
In file included from include/linux/string.h:253,
from include/linux/bitmap.h:11,
from include/linux/cpumask.h:12,
from include/linux/smp.h:13,
from include/linux/lockdep.h:14,
from include/linux/spinlock.h:62,
from include/linux/mmzone.h:8,
from include/linux/gfp.h:6,
from include/linux/slab.h:15,
from drivers/usb/serial/whiteheat.c:17:
In function 'fortify_memcpy_chk',
inlined from 'firm_send_command' at drivers/usb/serial/whiteheat.c:587:4:
include/linux/fortify-string.h:328:25: warning: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Wattribute-warning]
328 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In commit 9ea9b9c48387 ("remove the lightnvm subsystem") the lightnvm
subsystem was removed as there is no hardware in the wild for it, and
the code is known to have problems. This should also be disabled for
older LTS kernels as well to prevent anyone from accidentally using it.
Cc: Christoph Hellwig <hch@lst.de> Cc: Matias Bjørling <mb@lightnvm.io> Cc: Javier González <javier@javigon.com> Cc: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Minh Yuan reported a concurrency use-after-free issue in the floppy code
between raw_cmd_ioctl and seek_interrupt.
[ It turns out this has been around, and that others have reported the
KASAN splats over the years, but Minh Yuan had a reproducer for it and
so gets primary credit for reporting it for this fix - Linus ]
The problem is, this driver tends to break very easily and nowadays,
nobody is expected to use FDRAWCMD anyway since it was used to
manipulate non-standard formats. The risk of breaking the driver is
higher than the risk presented by this race, and accessing the device
requires privileges anyway.
Let's just add a config option to completely disable this ioctl and
leave it disabled by default. Distros shouldn't use it, and only those
running on antique hardware might need to enable it.
If the file system does not use bigalloc, calculating the overhead is
cheap, so force the recalculation of the overhead so we don't have to
trust the precalculated overhead in the superblock.
The kernel calculation was underestimating the overhead by not taking
into account the reserved gdt blocks. With this change, the overhead
calculated by the kernel matches the overhead calculation in mke2fs.
Syzbot found an issue [1] in ext4_fallocate().
The C reproducer [2] calls fallocate(), passing size 0xffeffeff000ul,
and offset 0x1000000ul, which, when added together exceed the
bitmap_maxbytes for the inode. This triggers a BUG in
ext4_ind_remove_space(). According to the comments in this function
the 'end' parameter needs to be one block after the last block to be
removed. In the case when the BUG is triggered it points to the last
block. Modify the ext4_punch_hole() function and add constraint that
caps the length to satisfy the one before laster block requirement.
Function syscall_trace_exit expects pointer to pt_regs. However
r0 is also used to keep syscall return value. Restore pointer
to pt_regs before calling syscall_trace_exit.
These two bug are here:
list_for_each_entry_safe_continue(w, n, list,
power_list);
list_for_each_entry_safe_continue(w, n, list,
power_list);
After the list_for_each_entry_safe_continue() exits, the list iterator
will always be a bogus pointer which point to an invalid struct objdect
containing HEAD member. The funciton poniter 'w->event' will be a
invalid value which can lead to a control-flow hijack if the 'w' can be
controlled.
The original intention was to continue the outer list_for_each_entry_safe()
loop with the same entry if w->event is NULL, but misunderstanding the
meaning of list_for_each_entry_safe_continue().
So just add a 'continue;' to fix the bug.
Cc: stable@vger.kernel.org Fixes: 163cac061c973 ("ASoC: Factor out DAPM sequence execution") Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com> Link: https://lore.kernel.org/r/20220329012134.9375-1-xiam0nd.tong@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Given a sufficiently large number of actions, while copying and
reserving memory for a new action of a new flow, if next_offset is
greater than MAX_ACTIONS_BUFSIZE, the function reserve_sfa_size() does
not return -EMSGSIZE as expected, but it allocates MAX_ACTIONS_BUFSIZE
bytes increasing actions_len by req_size. This can then lead to an OOB
write access, especially when further actions need to be copied.
Fix it by rearranging the flow action size check.
KASAN splat below:
==================================================================
BUG: KASAN: slab-out-of-bounds in reserve_sfa_size+0x1ba/0x380 [openvswitch]
Write of size 65360 at addr ffff888147e4001c by task handler15/836
The bug is here:
__func__, desc, &desc->tx_dma_desc.phys, ret, cookie, residue);
The list iterator 'desc' will point to a bogus position containing
HEAD if the list is empty or no element is found. To avoid dev_dbg()
prints a invalid address, use a new variable 'iter' as the list
iterator, while use the origin variable 'desc' as a dedicated
pointer to point to the found element.
Before detecting the cable type on the dma bar, the driver should check
whether the 'bmdma_addr' is zero, which means the adapter does not
support DMA, otherwise we will get the following error:
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kzalloc() is a memory allocation function which can return NULL when
some internal memory errors happen. So it is better to check it to
prevent potential wrong memory access.
Besides, since mdp5_plane_reset() is void type, so we should better
set `plane-state` to NULL after releasing it.
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/481055/ Link: https://lore.kernel.org/r/tencent_8E2A1C78140EE1784AB2FF4B2088CC0AB908@qq.com Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function ‘brcmf_sdio_drivestrengthinit’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3798:2: error: case label does not reduce to an integer constant
case SDIOD_DRVSTR_KEY(BRCM_CC_43143_CHIP_ID, 17):
^~~~
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3809:2: error: case label does not reduce to an integer constant
case SDIOD_DRVSTR_KEY(BRCM_CC_43362_CHIP_ID, 13):
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Arend van Spriel <aspriel@gmail.com> Cc: Franky Lin <franky.lin@broadcom.com> Cc: Hante Meuleman <hante.meuleman@broadcom.com> Cc: Kalle Valo <kvalo@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: brcm80211-dev-list.pdl@broadcom.com Cc: netdev@vger.kernel.org Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/Ykx0iRlvtBnKqtbG@zn.tnic Signed-off-by: Sasha Levin <sashal@kernel.org>
Use the IOCB_DIRECT indicator flag on the I/O context rather than checking to
see if the file was opened O_DIRECT.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Steve French <sfrench@samba.org>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: linux-cifs@vger.kernel.org Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
sound/usb/midi.c: In function ‘snd_usbmidi_out_endpoint_create’:
sound/usb/midi.c:1389:2: error: case label does not reduce to an integer constant
case USB_ID(0xfc08, 0x0101): /* Unknown vendor Cable */
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
[ A slight correction with parentheses around the argument by tiwai ]
netlink_dump() is allocating an skb, reserves space in it
but forgets to reset network header.
This allows a BPF program, invoked later from sk_filter()
to access uninitialized kernel memory from the reserved
space.
Theorically mac header reset could be omitted, because
it is set to a special initial value.
bpf_internal_load_pointer_neg_helper calls skb_mac_header()
without checking skb_mac_header_was_set().
Relying on skb->len not being too big seems fragile.
We also could add a sanity check in bpf_internal_load_pointer_neg_helper()
to avoid surprises in the future.
packet_sock xmit could be dev_queue_xmit, which also returns negative
errors. So only checking positive errors is not enough, or userspace
sendmsg may return success while packet is not send out.
Move the net_xmit_errno() assignment in the braces as checkpatch.pl said
do not use assignment in if condition.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Flavio Leitner <fbl@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a rawmidi output stream is closed, it calls the drain at first,
then does trigger-off only when the drain returns -ERESTARTSYS as a
fallback. It implies that each driver should turn off the stream
properly after the drain. Meanwhile, USB-audio MIDI interface didn't
change the port->active flag after the drain. This may leave the
output work picking up the port that is closed right now, which
eventually leads to a use-after-free for the already released rawmidi
object.
This patch fixes the bug by properly clearing the port->active flag
after the output drain.
Before this patch, function read_rindex_entry called compute_bitstructs
before it allocated a glock for the rgrp. But if compute_bitstructs found
a problem with the rgrp, it called gfs2_consist_rgrpd, and that called
gfs2_dump_glock for rgd->rd_gl which had not yet been assigned.
read_rindex_entry
compute_bitstructs
gfs2_consist_rgrpd
gfs2_dump_glock <---------rgd->rd_gl was not set.
This patch changes read_rindex_entry so it assigns an rgrp glock before
calling compute_bitstructs so gfs2_dump_glock does not reference an
unassigned pointer. If an error is discovered, the glock must also be
put, so a new goto and label were added.
Reported-by: syzbot+c6fd14145e2f62ca0784@syzkaller.appspotmail.com Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arthur Marsh reported we would hit the error below when building kernel
with gcc-12:
CC mm/page_alloc.o
mm/page_alloc.c: In function `mem_init_print_info':
mm/page_alloc.c:8173:27: error: comparison between two arrays [-Werror=array-compare]
8173 | if (start <= pos && pos < end && size > adj) \
|
In C++20, the comparision between arrays should be warned.
Link: https://lkml.kernel.org/r/20211125130928.32465-1-sxwjean@me.com Signed-off-by: Xiongwei Song <sxwjean@gmail.com> Reported-by: Arthur Marsh <arthur.marsh@internode.on.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Khem Raj <raj.khem@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With GCC 12, -Wstringop-overread was warning about an implicit cast from
char[6] to char[8]. However, the extra 2 bytes are always thrown away,
alignment doesn't matter, and the risk of hitting the edge of unallocated
memory has been accepted, so this prototype can just be converted to a
regular char *. Silences:
net/core/dev.c: In function ‘bpf_prog_run_generic_xdp’: net/core/dev.c:4618:21: warning: ‘ether_addr_equal_64bits’ reading 8 bytes from a region of size 6 [-Wstringop-overread]
4618 | orig_host = ether_addr_equal_64bits(eth->h_dest, > skb->dev->dev_addr);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
net/core/dev.c:4618:21: note: referencing argument 1 of type ‘const u8[8]’ {aka ‘const unsigned char[8]’}
net/core/dev.c:4618:21: note: referencing argument 2 of type ‘const u8[8]’ {aka ‘const unsigned char[8]’}
In file included from net/core/dev.c:91: include/linux/etherdevice.h:375:20: note: in a call to function ‘ether_addr_equal_64bits’
375 | static inline bool ether_addr_equal_64bits(const u8 addr1[6+2],
| ^~~~~~~~~~~~~~~~~~~~~~~
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de> Tested-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://lore.kernel.org/netdev/20220212090811.uuzk6d76agw2vv73@pengutronix.de Cc: Jakub Kicinski <kuba@kernel.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Khem Raj <raj.khem@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the latent entropy plugin mostly doesn't derive entropy from
get_random_const() for measuring the call graph, when __latent_entropy is
applied to a constant, then it's initialized statically to output from
get_random_const(). In that case, this data is derived from a 64-bit
seed, which means a buffer of 512 bits doesn't really have that amount
of compile-time entropy.
This patch fixes that shortcoming by just buffering chunks of
/dev/urandom output and doling it out as requested.
At the same time, it's important that we don't break the use of
-frandom-seed, for people who want the runtime benefits of the latent
entropy plugin, while still having compile-time determinism. In that
case, we detect whether gcc's set_random_seed() has been called by
making a call to get_random_seed(noinit=true) in the plugin init
function, which is called after set_random_seed() is called but before
anything that calls get_random_seed(noinit=false), and seeing if it's
zero or not. If it's not zero, we're in deterministic mode, and so we
just generate numbers with a basic xorshift prng.
Note that we don't detect if -frandom-seed is being used using the
documented local_tick variable, because it's assigned via:
local_tick = (unsigned) tv.tv_sec * 1000 + tv.tv_usec / 1000;
which may well overflow and become -1 on its own, and so isn't
reliable: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=105171
[kees: The 256 byte rnd_buf size was chosen based on average (250),
median (64), and std deviation (575) bytes of used entropy for a
defconfig x86_64 build]
Fixes: 38addce8b600 ("gcc-plugins: Add latent_entropy plugin") Cc: stable@vger.kernel.org Cc: PaX Team <pageexec@freemail.hu> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Kees Cook <keescook@chromium.org> Link: https://lore.kernel.org/r/20220405222815.21155-1-Jason@zx2c4.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: beb58aa39e6e ("i2c: PA Semi SMBus driver") Signed-off-by: Martin Povišer <povik+lin@cutebit.org> Reviewed-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The check in flush_smp_call_function_queue() for callbacks that are sent
to offline CPUs currently checks whether the queue is empty.
However, flush_smp_call_function_queue() has just deleted all the
callbacks from the queue and moved all the entries into a local list.
This checks would only be positive if some callbacks were added in the
short time after llist_del_all() was called. This does not seem to be
the intention of this check.
Change the check to look at the local list to which the entries were
moved instead of the queue from which all the callbacks were just
removed.
Fixes: 8d056c48e4862 ("CPU hotplug, smp: flush any pending IPI callbacks before CPU offline") Signed-off-by: Nadav Amit <namit@vmware.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20220319072015.1495036-1-namit@vmware.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With newer versions of GCC, there is a panic in da850_evm_config_emac()
when booting multi_v5_defconfig in QEMU under the palmetto-bmc machine:
Unable to handle kernel NULL pointer dereference at virtual address 00000020
pgd = (ptrval)
[00000020] *pgd=00000000
Internal error: Oops: 5 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 5.15.0 #1
Hardware name: Generic DT based system
PC is at da850_evm_config_emac+0x1c/0x120
LR is at do_one_initcall+0x50/0x1e0
The emac_pdata pointer in soc_info is NULL because davinci_soc_info only
gets populated on davinci machines but da850_evm_config_emac() is called
on all machines via device_initcall().
Move the rmii_en assignment below the machine check so that it is only
dereferenced when running on a supported SoC.
The kmemleak_*_phys() apis do not check the address for lowmem's min
boundary, while the caller may pass an address below lowmem, which will
trigger an oops:
The callers may not quite know the actual address they pass(e.g. from
devicetree). So the kmemleak_*_phys() apis should guarantee the address
they finally use is in lowmem range, so check the address for lowmem's
min boundary.
Link: https://lkml.kernel.org/r/20220413122925.33856-1-patrick.wang.shcn@gmail.com Signed-off-by: Patrick Wang <patrick.wang.shcn@gmail.com> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 6aa303defb74 ("mm, vmscan: only allocate and reclaim from
zones with pages managed by the buddy allocator") only zones with free
memory are included in a built zonelist. This is problematic when e.g.
all memory of a zone has been ballooned out when zonelists are being
rebuilt.
The decision whether to rebuild the zonelists when onlining new memory
is done based on populated_zone() returning 0 for the zone the memory
will be added to. The new zone is added to the zonelists only, if it
has free memory pages (managed_zone() returns a non-zero value) after
the memory has been onlined. This implies, that onlining memory will
always free the added pages to the allocator immediately, but this is
not true in all cases: when e.g. running as a Xen guest the onlined new
memory will be added only to the ballooned memory list, it will be freed
only when the guest is being ballooned up afterwards.
Another problem with using managed_zone() for the decision whether a
zone is being added to the zonelists is, that a zone with all memory
used will in fact be removed from all zonelists in case the zonelists
happen to be rebuilt.
Use populated_zone() when building a zonelist as it has been done before
that commit.
There was a report that QubesOS (based on Xen) is hitting this problem.
Xen has switched to use the zone device functionality in kernel 5.9 and
QubesOS wants to use memory hotplugging for guests in order to be able
to start a guest with minimal memory and expand it as needed. This was
the report leading to the patch.
Link: https://lkml.kernel.org/r/20220407120637.9035-1-jgross@suse.com Fixes: 6aa303defb74 ("mm, vmscan: only allocate and reclaim from zones with pages managed by the buddy allocator") Signed-off-by: Juergen Gross <jgross@suse.com> Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Acked-by: Michal Hocko <mhocko@suse.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Wei Yang <richard.weiyang@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>