During init we take care of regulatory stuff by disabling all
unavailable channels (see brcmf_construct_chaninfo) so this predisabling
them is not really required (and this patch won't change any behavior).
It will on the other hand allow more detailed runtime control over
channels which is the main reason for this change.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Cc: Lambdadroid <lambdadroid@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AMD severity grading function was introduced in kernel 4.1. The
current logic can possibly give MCE_AR_SEVERITY for uncorrectable
errors in kernel context. The system may then get stuck in a loop as
memory_failure() will try to handle the bad kernel memory and find it
busy.
Return MCE_PANIC_SEVERITY for all UC errors IN_KERNEL context on AMD
systems.
After:
b2f9d678e28c ("x86/mce: Check for faults tagged in EXTABLE_CLASS_FAULT exception table entries")
was accepted in v4.6, this issue was masked because of the tail-end attempt
at kernel mode recovery in the #MC handler.
However, uncorrectable errors IN_KERNEL context should always be considered
unrecoverable and cause a panic.
Make sure to stop any submitted interrupt and bulk-out URBs before
returning after failed probe and when the port is being unbound to avoid
later NULL-pointer dereferences in the completion callbacks.
Also fix up the related and broken I/O cancellation on failed open and
on close. (Note that port->write_urb was never submitted.)
BUG: KASAN: use-after-free in ffs_free_inst+... [usb_f_fs] at addr ...
Write of size 8 by task ...
This is observed after "ffs-test" is run and interrupted. If after that
functionfs is unmounted and g_ffs module is unloaded, that use-after-free
occurs during g_ffs module removal.
Although the report indicates ffs_free_inst() function, the actual
use-after-free condition occurs in _ffs_free_dev() function, which
is probably inlined into ffs_free_inst().
This happens due to keeping the ffs_data reference in device structure
during functionfs unmounting, while ffs_data itself is freed as no longer
needed. The fix is to clear that reference in ffs_closed() function,
which is a counterpart of ffs_ready(), where the reference is stored.
Without this patch, K70 LUX keyboards don't work, saying
usb 3-3: unable to read config index 0 descriptor/all
usb 3-3: can't read configurations, error -110
usb usb3-port3: unable to enumerate USB device
Signed-off-by: Bernhard Rosenkraenzer <Bernhard.Rosenkranzer@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB kerneldoc says that the actual_length field "is read in
non-iso completion functions", but the usbfs driver uses it for all
URB types in processcompl(). Since not all of the host controller
drivers set actual_length for isochronous URBs, programs using usbfs
with some host controllers don't work properly. For example, Minas
reports that a USB camera controlled by libusb doesn't work properly
with a dwc2 controller.
It doesn't seem worthwhile to change the HCDs and the documentation,
since the in-kernel USB class drivers evidently don't rely on
actual_length for isochronous transfers. The easiest solution is for
usbfs to calculate the actual_length value for itself, by adding up
the lengths of the individual packets in an isochronous transfer.
The "qat-dh" DH implementation assumes that 'key' and 'g' can be copied
into a buffer with size 'p_size'. However it was never checked that
that was actually the case, which most likely allowed users to cause a
buffer underflow via KEYCTL_DH_COMPUTE.
Fix this by updating crypto_dh_decode_key() to verify this precondition
for all DH implementations.
If 'p' is 0 for the software Diffie-Hellman implementation, then
dh_max_size() returns 0. In the case of KEYCTL_DH_COMPUTE, this causes
ZERO_SIZE_PTR to be passed to sg_init_one(), which with
CONFIG_DEBUG_SG=y triggers the 'BUG_ON(!virt_addr_valid(buf));' in
sg_set_buf().
Fix this by making crypto_dh_decode_key() reject 0 for 'p'. p=0 makes
no sense for any DH implementation because 'p' is supposed to be a prime
number. Moreover, 'mod 0' is not mathematically defined.
Consistently use types from linux/types.h to fix the following
linux/rds.h userspace compilation errors:
/usr/include/linux/rds.h:106:2: error: unknown type name 'uint8_t'
uint8_t name[32];
/usr/include/linux/rds.h:107:2: error: unknown type name 'uint64_t'
uint64_t value;
/usr/include/linux/rds.h:117:2: error: unknown type name 'uint64_t'
uint64_t next_tx_seq;
/usr/include/linux/rds.h:118:2: error: unknown type name 'uint64_t'
uint64_t next_rx_seq;
/usr/include/linux/rds.h:121:2: error: unknown type name 'uint8_t'
uint8_t transport[TRANSNAMSIZ]; /* null term ascii */
/usr/include/linux/rds.h:122:2: error: unknown type name 'uint8_t'
uint8_t flags;
/usr/include/linux/rds.h:129:2: error: unknown type name 'uint64_t'
uint64_t seq;
/usr/include/linux/rds.h:130:2: error: unknown type name 'uint32_t'
uint32_t len;
/usr/include/linux/rds.h:135:2: error: unknown type name 'uint8_t'
uint8_t flags;
/usr/include/linux/rds.h:139:2: error: unknown type name 'uint32_t'
uint32_t sndbuf;
/usr/include/linux/rds.h:144:2: error: unknown type name 'uint32_t'
uint32_t rcvbuf;
/usr/include/linux/rds.h:145:2: error: unknown type name 'uint64_t'
uint64_t inum;
/usr/include/linux/rds.h:153:2: error: unknown type name 'uint64_t'
uint64_t hdr_rem;
/usr/include/linux/rds.h:154:2: error: unknown type name 'uint64_t'
uint64_t data_rem;
/usr/include/linux/rds.h:155:2: error: unknown type name 'uint32_t'
uint32_t last_sent_nxt;
/usr/include/linux/rds.h:156:2: error: unknown type name 'uint32_t'
uint32_t last_expected_una;
/usr/include/linux/rds.h:157:2: error: unknown type name 'uint32_t'
uint32_t last_seen_una;
/usr/include/linux/rds.h:164:2: error: unknown type name 'uint8_t'
uint8_t src_gid[RDS_IB_GID_LEN];
/usr/include/linux/rds.h:165:2: error: unknown type name 'uint8_t'
uint8_t dst_gid[RDS_IB_GID_LEN];
/usr/include/linux/rds.h:167:2: error: unknown type name 'uint32_t'
uint32_t max_send_wr;
/usr/include/linux/rds.h:168:2: error: unknown type name 'uint32_t'
uint32_t max_recv_wr;
/usr/include/linux/rds.h:169:2: error: unknown type name 'uint32_t'
uint32_t max_send_sge;
/usr/include/linux/rds.h:170:2: error: unknown type name 'uint32_t'
uint32_t rdma_mr_max;
/usr/include/linux/rds.h:171:2: error: unknown type name 'uint32_t'
uint32_t rdma_mr_size;
/usr/include/linux/rds.h:212:9: error: unknown type name 'uint64_t'
typedef uint64_t rds_rdma_cookie_t;
/usr/include/linux/rds.h:215:2: error: unknown type name 'uint64_t'
uint64_t addr;
/usr/include/linux/rds.h:216:2: error: unknown type name 'uint64_t'
uint64_t bytes;
/usr/include/linux/rds.h:221:2: error: unknown type name 'uint64_t'
uint64_t cookie_addr;
/usr/include/linux/rds.h:222:2: error: unknown type name 'uint64_t'
uint64_t flags;
/usr/include/linux/rds.h:228:2: error: unknown type name 'uint64_t'
uint64_t cookie_addr;
/usr/include/linux/rds.h:229:2: error: unknown type name 'uint64_t'
uint64_t flags;
/usr/include/linux/rds.h:234:2: error: unknown type name 'uint64_t'
uint64_t flags;
/usr/include/linux/rds.h:240:2: error: unknown type name 'uint64_t'
uint64_t local_vec_addr;
/usr/include/linux/rds.h:241:2: error: unknown type name 'uint64_t'
uint64_t nr_local;
/usr/include/linux/rds.h:242:2: error: unknown type name 'uint64_t'
uint64_t flags;
/usr/include/linux/rds.h:243:2: error: unknown type name 'uint64_t'
uint64_t user_token;
/usr/include/linux/rds.h:248:2: error: unknown type name 'uint64_t'
uint64_t local_addr;
/usr/include/linux/rds.h:249:2: error: unknown type name 'uint64_t'
uint64_t remote_addr;
/usr/include/linux/rds.h:252:4: error: unknown type name 'uint64_t'
uint64_t compare;
/usr/include/linux/rds.h:253:4: error: unknown type name 'uint64_t'
uint64_t swap;
/usr/include/linux/rds.h:256:4: error: unknown type name 'uint64_t'
uint64_t add;
/usr/include/linux/rds.h:259:4: error: unknown type name 'uint64_t'
uint64_t compare;
/usr/include/linux/rds.h:260:4: error: unknown type name 'uint64_t'
uint64_t swap;
/usr/include/linux/rds.h:261:4: error: unknown type name 'uint64_t'
uint64_t compare_mask;
/usr/include/linux/rds.h:262:4: error: unknown type name 'uint64_t'
uint64_t swap_mask;
/usr/include/linux/rds.h:265:4: error: unknown type name 'uint64_t'
uint64_t add;
/usr/include/linux/rds.h:266:4: error: unknown type name 'uint64_t'
uint64_t nocarry_mask;
/usr/include/linux/rds.h:269:2: error: unknown type name 'uint64_t'
uint64_t flags;
/usr/include/linux/rds.h:270:2: error: unknown type name 'uint64_t'
uint64_t user_token;
/usr/include/linux/rds.h:274:2: error: unknown type name 'uint64_t'
uint64_t user_token;
/usr/include/linux/rds.h:275:2: error: unknown type name 'int32_t'
int32_t status;
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On the kernel side, sockaddr_storage is #define'd to
__kernel_sockaddr_storage. Replacing struct sockaddr_storage with
struct __kernel_sockaddr_storage defined by <linux/socket.h> fixes
the following linux/rds.h userspace compilation error:
/usr/include/linux/rds.h:226:26: error: field 'dest_addr' has incomplete type
struct sockaddr_storage dest_addr;
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code in arch/mips/netlogic/common/irq.c which handles the XLP PIC fails
to build in XLR configurations due to cpu_is_xlp9xx not being defined,
leading to the following build failure:
arch/mips/netlogic/common/irq.c: In function ‘xlp_of_pic_init’:
arch/mips/netlogic/common/irq.c:298:2: error: implicit declaration
of function ‘cpu_is_xlp9xx’ [-Werror=implicit-function-declaration]
if (cpu_is_xlp9xx()) {
^
Although the code was conditional upon CONFIG_OF which is indirectly
selected by CONFIG_NLM_XLP_BOARD but not CONFIG_NLM_XLR_BOARD, the
failing XLR with CONFIG_OF configuration can be configured manually or
by randconfig.
Fix the build failure by making the affected XLP PIC code conditional
upon CONFIG_CPU_XLP which is used to guard the inclusion of
asm/netlogic/xlp-hal/xlp.h that provides the required cpu_is_xlp9xx
function.
[ralf@linux-mips.org: Fixed up as per Jayachandran's suggestion.]
On systems with CM3, we must ensure that the L1 & L2 ECC enables are set
to the same value. This is presumed by the hardware & cache corruption
can occur when it is not the case. Support enabling & disabling the L2
ECC checking on CM3 systems where this is controlled via a GCR, and
ensure that it matches the state of L1 ECC checking. Remove I6400 from
the switch statement it will no longer hit, and which was incorrect
since the L2 ECC enable bit isn't in the CP0 ErrCtl register.
Memories managed through boot_mem_map are generally expected to define
non-crossing areas. However, if part of a larger memory block is marked
as reserved, it would still be added to bootmem allocator as an
available block and could end up being overwritten by the allocator.
Prevent this by explicitly marking the memory as reserved it if exists
in the range used by bootmem allocator.
Current init code initialises bootmem allocator with all of the low
memory that it assumes is available, but does not check for reserved
memory block, which can lead to corruption of data that may be stored
there.
Move bootmem's allocation map to a location that does not cross any
reserved regions
When building a kernel targeting a microMIPS ISA, recent GNU linkers
will fail the link if they cannot determine that the target of a branch
or jump is microMIPS code, with errors such as the following:
mips-img-linux-gnu-ld: arch/mips/built-in.o: .text+0x542c:
Unsupported jump between ISA modes; consider recompiling with
interlinking enabled.
mips-img-linux-gnu-ld: final link failed: Bad value
or:
./arch/mips/include/asm/uaccess.h:1017: warning: JALX to a
non-word-aligned address
Placing anything other than an instruction at the start of a function
written in assembly appears to trigger such errors. In order to prepare
for allowing us to follow function prologue macros with an EXPORT_SYMBOL
invocation, end the prologue macros (LEAD, NESTED & FEXPORT) with a
.insn directive. This ensures that the start of the function is marked
as code, which always makes sense for functions & safely prevents us
from hitting the link errors described above.
Signed-off-by: Paul Burton <paul.burton@imgtec.com> Reviewed-by: Maciej W. Rozycki <macro@imgtec.com> Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14508/ Signed-off-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add sanity checks for cport_quiesce and cport_clear before invoking the
callbacks as these function pointers are not required during the host
device registration. This follows the logic implemented elsewhere for
various other function pointers.
A retry count of 10 is likely to run into problems on X550 devices that
have to detect and reset unresponsive CS4227 devices. So, reduce the I2C
retry count to 3 for X550 and above. This should avoid any possible
regressions in existing devices.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BaseT adapters that are capable of supporting 100Mb are not reporting this
capability. This patch corrects the reporting so that 100Mb is shown as
supported on those adapters.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an interface is part of a namespace it is possible that
ixgbe_close() may be called while __ixgbe_shutdown() is running
which ends up in a double free WARN and/or a BUG in free_msi_irqs().
To handle this situation we extend the rtnl_lock() to protect the
call to netif_device_detach() and ixgbe_clear_interrupt_scheme()
in __ixgbe_shutdown() and check for netif_device_present()
to avoid clearing the interrupts second time in ixgbe_close();
Also extend the rtnl lock in ixgbe_resume() to netif_device_attach().
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that we free the IRQs in ixgbe_io_error_detected() when
responding to an PCIe AER error and also restore them when the
interface recovers from it.
Previously it was possible to trigger BUG_ON() check in free_msix_irqs()
in the case where we call ixgbe_remove() after a failed recovery from
AER error because the interrupts were not freed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch ensures that the advertised link speeds are configured
for X553 KR/KX backplane. Without this patch the link remains at
1G when resuming from low power after being downshifted by LPLU.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once device_register is called for a device its attributes might be
accessed. As the callbacks of a lcd device's attributes make use of the
lcd_ops, the respective member must be setup before calling
device_register.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pseudo DMA transfer codes in VX222 and VX-pocket driver have a
slight bug where they check the buffer boundary wrongly, and may
overflow. Also, the zero sample count might be handled badly for the
playback (although it shouldn't happen in theory). This patch
addresses these issues.
The update of stream costs significantly, and we should avoid it
unless the stream really has started. Check pipe->running flag
instead of pipe->prepared.
Clear the VendorVersion in the PLOGI/PLOGI ACC payload
Vendor version info may have been set on fabric login. Before sending
PLOGI payloads, ensure that it's cleared.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct issue leading to oops during link reset. Missing vport pointer.
[mkp: fixed typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct host name in symbolic_name field of nameserver registrations
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FCoE VPort enable-disable does not bring up the VPort.
VPI structure needed to be initialized before being re-registered.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On loosely ordered memory systems (PPC for example), the WQE elements
were being updated in memory, but not necessarily flushed before the
separate doorbell was written to hw which would cause hw to dma the
WQE element. Thus, the hardware occasionally received partially
updated WQE data.
Add the memory barrier after updating the WQE memory.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <james.smart@broadcom.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the __irq_entry annotation to the default x86
platform IRQ handlers. ftrace's function_graph tracer uses the
__irq_entry annotation to notify the entry and return of IRQ
handlers.
Several lifecycle events in the rtl8188eu driver are logged using the
DBG_88E_LEVEL macro from rtw_debug.h, which is tagged as ERROR
regardless of the actual level. Below are dmesg excerpts after loading
and unloading the module, the messages are misleading as there was no
error.
For TCP sockets, TX timestamps are only captured when the user data
is successfully and fully written to the socket. In many cases,
however, TCP writes can be partial for which no timestamp is
collected.
Collect timestamps whenever any user data is (fully or partially)
copied into the socket. Pass tcp_write_queue_tail to tcp_tx_timestamp
instead of the local skb pointer since it can be set to NULL on
the error path.
Note that tcp_write_queue_tail can be NULL, even if bytes have been
copied to the socket. This is because acknowledgements are being
processed in tcp_sendmsg(), and by the time tcp_tx_timestamp is
called tcp_write_queue_tail can be NULL. For such cases, this patch
does not collect any timestamps (i.e., it is best-effort).
This patch is written with suggestions from Willem de Bruijn and
Eric Dumazet.
Change-log V1 -> V2:
- Use sockc.tsflags instead of sk->sk_tsflags.
- Use the same code path for normal writes and errors.
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Neal Cardwell <ncardwell@google.com> Cc: Martin KaFai Lau <kafai@fb.com> Acked-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UFS device requires to perform bkops (back ground operations) periodically
but host can control (via auto-bkops parameter of device) when device can
perform bkops based on its performance requirements. In general, host
would like to enable the device's auto-bkops only when it's not doing any
regular data transfer but sometimes device may not behave properly if host
keeps the auto-bkops disabled. This change adds the capability to let the
device auto-bkops always enabled except suspend.
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/scsi/ufs/ufs-qcom.ko | grep alias
$
After this patch:
$ modinfo drivers/scsi/ufs/ufs-qcom.ko | grep alias
alias: of:N*T*Cqcom,ufshcC*
alias: of:N*T*Cqcom,ufshc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to ixgbe, when an interface is part of a namespace it is
possible that igb_close() may be called while __igb_shutdown() is
running which ends up in a double free WARN and/or a BUG in
free_msi_irqs().
Extend the rtnl_lock() to protect the call to netif_device_detach() and
igb_clear_interrupt_scheme() in __igb_shutdown() and check for
netif_device_present() to avoid calling igb_clear_interrupt_scheme() a
second time in igb_close().
Also extend the rtnl lock in igb_resume() to netif_device_attach().
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com> Acked-by: Alexander Duyck <alexander.h.duyck@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several people have reported firmware leaving the I210/I211 PHY's page
select register set to something other than the default of zero. This
causes the first accesses, PHY_IDx register reads, to access something
else, resulting in device probe failure:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of 0000:01:00.0 failed with error -2
This problem began for them after a previous patch I submitted was
applied:
I personally experienced this problem after attempting to PXE boot from
I210 devices using this firmware:
Intel(R) Boot Agent GE v1.5.78
Copyright (C) 1997-2014, Intel Corporation
Resetting the PHY before reading from it, ensures the page select
register is in its default state and doesn't make assumptions about
the PHY's register set before the PHY has been probed.
Cc: Matwey V. Kornilov <matwey@sai.msu.ru> Cc: Chris Arges <carges@vectranetworks.com> Cc: Jochen Henneberg <jh@henneberg-systemdesign.com> Signed-off-by: Aaron Sierra <asierra@xes-inc.com> Tested-by: Matwey V. Kornilov <matwey@sai.msu.ru> Tested-by: Chris J Arges <christopherarges@gmail.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here, If devm_ioremap_nocache will fail. It will return NULL.
Kernel can run into a NULL-pointer dereference. This error check
will avoid NULL pointer dereference.
Note that the value is still glitchy during off mode transitions as documented
in spz319f.pdf "Advisory 1.45". It's best to use external pulls instead of
relying on the internal ones for off mode and even then anything pulled up
will get driven down momentarily on off mode restore for GPIO banks other
than bank1.
Multiple IES API resets can cause a race condition where the mailbox
interrupt request bits can be cleared before being handled. This can
leave certain mailbox messages from the PF to be untreated and the PF
will enter in some inactive state. If this situation occurs, the IES API
will initiate a mailbox version reset which, then, trigger a mailbox
state change. Once this mailbox transition occurs (from OPEN to CONNECT
state), a request for reset will be returned.
This ensures that PF will undergo a reset whenever IES API encounters an
unknown global mailbox interrupt event or whenever the IES API
terminates.
extcon-palmas must be child of palmas and expects parent's
drvdata to be valid. Check for non NULL parent drvdata and
fail if it is NULL. Not doing so will result in a NULL
pointer dereference later in the probe() parent drvdata
is NULL (e.g. misplaced extcon-palmas node in device tree).
This patch removes the potential problem of extcon_register_notifier()
when edev parameter is NULL. When edev is NULL, this function returns
the first extcon device which includes the sepecific external connector
of second paramter. But, it don't guarantee the same operation in all cases.
To remove this confusion and potential problem, this patch fixes it.
There's been numerous reported instances where BTUSB_QCA_ROME
bluetooth controllers stop functioning upon resume from suspend. These
devices seem to be losing power during suspend. Patch will detect a status
change on resume and perform a reset.
Eric Biggers [Fri, 17 Nov 2017 19:50:27 +0000 (11:50 -0800)]
arm: crypto: reduce priority of bit-sliced AES cipher
[ Not upstream because this is a minimal fix for a bug where arm32
kernels can use a much slower implementation of AES than is actually
available, potentially forcing vendors to disable encryption on their
devices.]
All the aes-bs (bit-sliced) and aes-ce (cryptographic extensions)
algorithms had a priority of 300. This is undesirable because it means
an aes-bs algorithm may be used when an aes-ce algorithm is available.
The aes-ce algorithms have much better performance (up to 10x faster).
Fix it by decreasing the priority of the aes-bs algorithms to 250.
This was fixed upstream by commit cc477bf64573 ("crypto: arm/aes -
replace bit-sliced OpenSSL NEON code"), but it was just a small part of
a complete rewrite. This patch just fixes the priority bug for older
kernels.
Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
dvb_detach(arg) calls symbol_put_addr(arg), where arg should be a pointer
to a function. Right now a pointer to state->dib7000p_ops is passed to
dvb_detach(), which causes a BUG() in symbol_put_addr() as discovered by
syzkaller. Pass state->dib7000p_ops.set_wbd_ref instead.
Commit f4757af ("staging: panel: Fix single-open policy race condition")
introduced in 3.19-rc1 attempted to fix a race condition on the open, but
failed to properly do it and used to exit without restoring the semaphore.
This results in -EBUSY being returned after the first open error until
the module is reloaded or the system restarted (ie: consecutive to a
dual open resulting in -EBUSY or to a permission error).
Fixes: f4757af85 # 3.19-rc1 Cc: Mariusz Gorski <marius.gorski@gmail.com> Signed-off-by: Willy Tarreau <w@1wt.eu>
[wt: driver is in misc/panel in 4.9] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch drops two incorrect usages of tcm_qla2xxx_free_cmd()
during TMR ABORT within tcm_qla2xxx_handle_data_work() and
tcm_qla2xxx_aborted_task(), which where attempting to dispatch
into workqueue context to do tcm_qla2xxx_complete_free() and
subsequently invoke transport_generic_free_cmd().
This is incorrect because during TMR ABORT target-core will
drop the outstanding se_cmd->cmd_kref references once it has
quiesced the se_cmd via transport_wait_for_tasks(), and in
the case of qla2xxx it should not attempt to do it's own
transport_generic_free_cmd() once the abort has occured.
As reported by Pascal, this was originally manifesting as a
BUG_ON(cmd->cmd_in_wq) in qlt_free_cmd() during TMR ABORT,
with a LIO backend that had sufficently high enough WRITE
latency to trigger a host side TMR ABORT_TASK.
(v2: Drop the qla_tgt_cmd->write_pending_abort_comp changes,
as they will be addressed in a seperate series)
Reported-by: Pascal de Bruijn <p.debruijn@unilogic.nl> Tested-by: Pascal de Bruijn <p.debruijn@unilogic.nl> Cc: Pascal de Bruijn <p.debruijn@unilogic.nl> Reported-by: Lukasz Engel <lukasz.engel@softax.pl> Cc: Lukasz Engel <lukasz.engel@softax.pl> Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com> Cc: Quinn Tran <quinn.tran@cavium.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allocate a task management request structure for all task management
requests, including task reassignment. This change avoids that the
se_tmr->response assignment dereferences an uninitialized se_tmr
pointer.
Reported-by: Moshe David <mdavid@infinidat.com> Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Cc: Moshe David <mdavid@infinidat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Upon stopping an AP interface the driver disable INFRA mode effectively
setting the interface in IBSS mode. However, this may affect other
interfaces running in INFRA mode. For instance, if user creates and stops
hostap daemon on virtual interface, then association cannot work on
primary interface because default BSS has been set to IBSS mode in
firmware side. The IBSS mode should be set when cfg80211 changes the
interface.
Reviewed-by: Wright Feng <wright.feng@cypress.com> Signed-off-by: Chi-hsien Lin <Chi-Hsien.Lin@cypress.com>
[kvalo@codeaurora.org: rephased commit log based on discussion] Signed-off-by: Wright Feng <wright.feng@cypress.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Cc: Philipp Rosenberger <p.rosenberger@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_KEYS_COMPAT is defined in arch-specific Kconfigs and is missing for
several 64-bit architectures : mips, parisc, tile.
At the moment and for those architectures, calling in 32-bit userspace the
keyctl syscall would return an ENOSYS error.
This patch moves the CONFIG_KEYS_COMPAT option to security/keys/Kconfig, to
make sure the compatibility wrapper is registered by default for any 64-bit
architecture as long as it is configured with CONFIG_COMPAT.
[DH: Modified to remove arm64 compat enablement also as requested by Eric
Biggers]
Signed-off-by: Bilal Amarni <bilal.amarni@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Arnd Bergmann <arnd@arndb.de>
cc: Eric Biggers <ebiggers3@gmail.com> Signed-off-by: James Morris <james.l.morris@oracle.com> Cc: James Cowgill <james.cowgill@mips.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was not a good idea. The custom hash table was a much better
fit for this purpose.
A fast lookup is not essential, in fact for most cases there is no lookup
at all because original tuple is not taken and can be used as-is.
What needs to be fast is insertion and deletion.
rhlist removal however requires a rhlist walk.
We can have thousands of entries in such a list if source port/addresses
are reused for multiple flows, if this happens removal requests are so
expensive that deletions of a few thousand flows can take several
seconds(!).
The advantages that we got from rhashtable are:
1) table auto-sizing
2) multiple locks
1) would be nice to have, but it is not essential as we have at
most one lookup per new flow, so even a million flows in the bysource
table are not a problem compared to current deletion cost.
2) is easy to add to custom hash table.
I tried to add hlist_node to rhlist to speed up rhltable_remove but this
isn't doable without changing semantics. rhltable_remove_fast will
check that the to-be-deleted object is part of the table and that
requires a list walk that we want to avoid.
Furthermore, using hlist_node increases size of struct rhlist_head, which
in turn increases nf_conn size.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196821 Reported-by: Ivan Babrou <ibobrik@gmail.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
successful insert into the bysource hash sets IPS_SRC_NAT_DONE status bit
so we can check that instead of presence of nat extension which requires
extra deref.
Turns out not to be a good idea in the stable kernels for now as Patrick
writes:
As discussed for 4.4 stable queue this patch might break
existing machines, if they use a different pinmux configuration
with their own bootloader.
ALSA sequencer core has a mechanism to load the enumerated devices
automatically, and it's performed in an off-load work. This seems
causing some race when a sequencer is removed while the pending
autoload work is running. As syzkaller spotted, it may lead to some
use-after-free:
BUG: KASAN: use-after-free in snd_rawmidi_dev_seq_free+0x69/0x70
sound/core/rawmidi.c:1617
Write of size 8 at addr ffff88006c611d90 by task kworker/2:1/567
Before trying to use CDC union descriptor, try to validate whether that it
is sane by checking that intf->altsetting->extra is big enough and that
descriptor bLength is not too big and not too small.
If the usbtest driver encounters a device with an IN bulk endpoint but
no OUT bulk endpoint, it will try to dereference a NULL pointer
(out->desc.bEndpointAddress). The problem can be solved by adding a
missing test.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Andrey Konovalov <andreyknvl@google.com> Tested-by: Andrey Konovalov <andreyknvl@google.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the reinstall prevention, the code I had added compares the
whole key. It turns out though that iwlwifi firmware doesn't
provide the TKIP TX MIC key as it's not needed in client mode,
and thus the comparison will always return false.
For client mode, thus always zero out the TX MIC key part before
doing the comparison in order to avoid accepting the reinstall
of the key with identical encryption and RX MIC key, but not the
same TX MIC key (since the supplicant provides the real one.)
Fixes: fdf7cb4185b6 ("mac80211: accept key reinstall without changing anything") Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a key is reinstalled we can reset the replay counters
etc. which can lead to nonce reuse and/or replay detection
being impossible, breaking security properties, as described
in the "KRACK attacks".
In particular, CVE-2017-13080 applies to GTK rekeying that
happened in firmware while the host is in D3, with the second
part of the attack being done after the host wakes up. In
this case, the wpa_supplicant mitigation isn't sufficient
since wpa_supplicant doesn't know the GTK material.
In case this happens, simply silently accept the new key
coming from userspace but don't take any action on it since
it's the same key; this keeps the PN replay counters intact.
Signed-off-by: Johannes Berg <johannes.berg@intel.com> Cc: Ben Hutchings <ben.hutchings@codethink.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ppp_release() tries to ensure that netdevices are unregistered before
decrementing the unit refcount and running ppp_destroy_interface().
This is all fine as long as the the device is unregistered by
ppp_release(): the unregister_netdevice() call, followed by
rtnl_unlock(), guarantee that the unregistration process completes
before rtnl_unlock() returns.
However, the device may be unregistered by other means (like
ppp_nl_dellink()). If this happens right before ppp_release() calling
rtnl_lock(), then ppp_release() has to wait for the concurrent
unregistration code to release the lock.
But rtnl_unlock() releases the lock before completing the device
unregistration process. This allows ppp_release() to proceed and
eventually call ppp_destroy_interface() before the unregistration
process completes. Calling free_netdev() on this partially unregistered
device will BUG():
------------[ cut here ]------------
kernel BUG at net/core/dev.c:8141!
invalid opcode: 0000 [#1] SMP
CPU: 1 PID: 1557 Comm: pppd Not tainted 4.14.0-rc2+ #4
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014
We could set the ->needs_free_netdev flag on PPP devices and move the
ppp_destroy_interface() logic in the ->priv_destructor() callback. But
that'd be quite intrusive as we'd first need to unlink from the other
channels and units that depend on the device (the ones that used the
PPPIOCCONNECT and PPPIOCATTACH ioctls).
Instead, we can just let the netdevice hold a reference on its
ppp_file. This reference is dropped in ->priv_destructor(), at the very
end of the unregistration process, so that neither ppp_release() nor
ppp_disconnect_channel() can call ppp_destroy_interface() in the interim.
Reported-by: Beniamino Galvani <bgalvani@redhat.com> Fixes: 8cb775bc0a34 ("ppp: fix device unregistration upon netns deletion") Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Davide found the following script triggers a NULL pointer
dereference:
ip l a name eth0 type dummy
tc q a dev eth0 parent :1 handle 1: htb
This is because for a freshly created netdevice noop_qdisc
is attached and when passing 'parent :1', kernel actually
tries to match the major handle which is 0 and noop_qdisc
has handle 0 so is matched by mistake. Commit 69012ae425d7
tries to fix a similar bug but still misses this case.
Handle 0 is not a valid one, should be just skipped. In
fact, kernel uses it as TC_H_UNSPEC.
Fixes: 69012ae425d7 ("net: sched: fix handling of singleton qdiscs with qdisc_hash") Fixes: 59cc1f61f09c ("net: sched:convert qdisc linked list to hashtable") Reported-by: Davide Caratti <dcaratti@redhat.com> Cc: Jiri Kosina <jkosina@suse.cz> Cc: Eric Dumazet <edumazet@google.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now when migrating sock to another one in sctp_sock_migrate(), it only
resets owner sk for the data in receive queues, not the chunks on out
queues.
It would cause that data chunks length on the sock is not consistent
with sk sk_wmem_alloc. When closing the sock or freeing these chunks,
the old sk would never be freed, and the new sock may crash due to
the overflow sk_wmem_alloc.
Although listen() should have returned error when one TCP-style socket
is in connecting (I may fix this one in another patch), it could also
be reproduced by peeling off an assoc.
This issue is there since very beginning.
This patch is to reset owner sk for the chunks on out queues so that
sk sk_wmem_alloc has correct value after accept one sock or peeloff
an assoc to one sock.
Note that when resetting owner sk for chunks on outqueue, it has to
sctp_clear_owner_w/skb_orphan chunks before changing assoc->base.sk
first and then sctp_set_owner_w them after changing assoc->base.sk,
due to that sctp_wfree and it's callees are using assoc->base.sk.
Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the name argument of dev_get_valid_name() contains "%d", it will try
to assign it a unit number in __dev__alloc_name() and return either the
unit number (>= 0) or an error code (< 0).
Considering positive values as error values prevent tun device creations
relying this mechanism, therefor we should only consider negative values
as errors here.
Signed-off-by: Julien Gomes <julien@arista.com> Acked-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When receiving a Toobig icmpv6 packet, ip6gre_err would just set
tunnel dev's mtu, that's not enough. For skb_dst(skb)'s pmtu may
still be using the old value, it has no chance to be updated with
tunnel dev's mtu.
Jianlin found this issue by reducing route's mtu while running
netperf, the performance went to 0.
ip6ip6 and ip4ip6 tunnel can work well with this, as they lookup
the upper dst and update_pmtu it's pmtu or icmpv6_send a Toobig
to upper socket after setting tunnel dev's mtu.
We couldn't do that for ip6_gre, as gre's inner packet could be
any protocol, it's difficult to handle them (like lookup upper
dst) in a good way.
So this patch is to fix it by updating skb_dst(skb)'s pmtu when
dev->mtu < skb_dst(skb)'s pmtu in tx path. It's safe to do this
update there, as usually dev->mtu <= skb_dst(skb)'s pmtu and no
performance regression can be caused by this.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The similar fix in patch 'ipip: only increase err_count for some
certain type icmp in ipip_err' is needed for ip6gre_err.
In Jianlin's case, udp netperf broke even when receiving a TooBig
icmpv6 packet.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
t->err_count is used to count the link failure on tunnel and an err
will be reported to user socket in tx path if t->err_count is not 0.
udp socket could even return EHOSTUNREACH to users.
Since commit fd58156e456d ("IPIP: Use ip-tunneling code.") removed
the 'switch check' for icmp type in ipip_err(), err_count would be
increased by the icmp packet with ICMP_EXC_FRAGTIME code. an link
failure would be reported out due to this.
In Jianlin's case, when receiving ICMP_EXC_FRAGTIME a icmp packet,
udp netperf failed with the err:
send_data: data send error: No route to host (errno 113)
We expect this error reported from tunnel to socket when receiving
some certain type icmp, but not ICMP_EXC_FRAGTIME, ICMP_SR_FAILED
or ICMP_PARAMETERPROB ones.
This patch is to bring 'switch check' for icmp type back to ipip_err
so that it only reports link failure for the right type icmp, just as
in ipgre_err() and ipip6_err().
Fixes: fd58156e456d ("IPIP: Use ip-tunneling code.") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Double free of skb_array in tap module is causing kernel panic. When
tap_set_queue() fails we free skb_array right away by calling
skb_array_cleanup(). However, later on skb_array_cleanup() is called
again by tap_sock_destruct through sock_put(). This patch fixes that
issue.
Fixes: 362899b8725b35e3 (macvtap: switch to use skb array) Signed-off-by: Girish Moodalbail <girish.moodalbail@oracle.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
socket_diag shows information only about sockets from a namespace where
a diag socket lives.
But if we request information about one unix socket, the kernel don't
check that its netns is matched with a diag socket namespace, so any
user can get information about any unix socket in a system. This looks
like a bug.
v2: add a Fixes tag
Fixes: 51d7cccf0723 ("net: make sock diag per-namespace") Signed-off-by: Andrei Vagin <avagin@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In my first attempt to fix the lockdep splat, I forgot we could
enter inet_csk_route_req() with a freshly allocated request socket,
for which refcount has not yet been elevated, due to complex
SLAB_TYPESAFE_BY_RCU rules.
We either are in rcu_read_lock() section _or_ we own a refcount on the
request.
Correct RCU verb to use here is rcu_dereference_check(), although it is
not possible to prove we actually own a reference on a shared
refcount :/
In v2, I added ireq_opt_deref() helper and use in three places, to fix other
possible splats.
Thread running inet_csk_route_req() owns a reference on the request
socket, so we have the guarantee ireq->ireq_opt wont be changed or
freed.
lockdep can enforce this invariant for us.
Fixes: c92e8c02fe66 ("tcp/dccp: fix ireq->opt races") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 9b9742022888 ("sctp: support ipv6 nonlocal bind")
introduced support for the above options as v4 sctp did,
so patched sctp_v6_available().
In the v4 implementation it's enough, because
sctp_inet_bind_verify() just returns with sctp_v4_available().
However sctp_inet6_bind_verify() has an extra check before that
for link-local scope_id, which won't respect the above options.
Added the checks before calling ipv6_chk_addr(), but
not before the validation of scope_id.
after (w/ both options):
./v6test fe80::10 sctp
bind success, errno: 0 (Success)
Signed-off-by: Laszlo Toth <laszlth@gmail.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log