When the user sets count to zero the string buffer would remain
completely uninitialized which causes the kernel to parse its
own stack data, potentially leading to an info leak. In addition
to that, the string might be not terminated properly when the
user data does not contain a 0-terminator.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org> Reviewed-by: Christoph Böhmwalder <christoph@boehmwalder.at> Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ICMP implementation currently replies to an ICMP time exceeded message
(type 11) with an ICMP host unreachable message (type 3, code 1).
However, time exceeded messages can either represent "time to live exceeded
in transit" (code 0) or "fragment reassembly time exceeded" (code 1).
Unconditionally replying to "fragment reassembly time exceeded" with
host unreachable messages might cause unjustified connection resets
which are now easily triggered as UFO has been removed, because, in turn,
sending large buffers triggers IP fragmentation.
The issue can be easily reproduced by running a lot of UDP streams
which is likely to trigger IP fragmentation:
# start netserver in the test namespace
ip netns add test
ip netns exec test netserver
# create a VETH pair
ip link add name veth0 type veth peer name veth0 netns test
ip link set veth0 up
ip -n test link set veth0 up
for i in $(seq 20 29); do
# assign addresses to both ends
ip addr add dev veth0 192.168.$i.1/24
ip -n test addr add dev veth0 192.168.$i.2/24
# wait
send_data: data send error: No route to host (errno 113)
netperf: send_omni: send_data failed: No route to host
We need to differentiate instead: if fragment reassembly time exceeded
is reported, we need to silently drop the packet,
if time to live exceeded is reported, maintain the current behaviour.
In both cases increment the related error count "icmpInTimeExcds".
While at it, fix a typo in a comment, and convert the if statement
into a switch to mate it more readable.
Signed-off-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ndo_open and ndo_stop are called RTNL lock should be held.
In this specific case ipoib_ib_dev_open calls the offloaded ndo_open
which re-sets the number of TX queue assuming RTNL lock is held.
Since RTNL lock is not held, RTNL assert will fail.
According to the C standard the behavior of computations with
integer operands is as follows:
* A computation involving unsigned operands can never overflow,
because a result that cannot be represented by the resulting
unsigned integer type is reduced modulo the number that is one
greater than the largest value that can be represented by the
resulting type.
* The behavior for signed integer underflow and overflow is
undefined.
Hence only use unsigned integers when checking for integer
overflow.
This patch is what I came up with after having analyzed the
following smatch warnings:
This patch intoduces a slight adjustment for macvlan to address the fact
that in source mode I was seeing two copies of any packet addressed to the
macvlan interface being delivered where there should have been only one.
The issue appears to be that one copy was delivered based on the source MAC
address and then the second copy was being delivered based on the
destination MAC address. To fix it I am just treating a unicast address
match as though it is not a match since source based macvlan isn't supposed
to be matching based on the destination MAC anyway.
Fixes: 79cf79abce71 ("macvlan: add source mode") Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We could allocate less memory than intended because we do:
bfad->regdata = kzalloc(len << 2, GFP_KERNEL);
The shift can overflow leading to a crash. This is debugfs code so the
impact is very small. I fixed the network version of this in March with
commit 13e2d5187f6b ("bna: integer overflow bug in debugfs").
Fixes: ab2a9ba189e8 ("[SCSI] bfa: add debugfs support") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver may sleep under a spinlock, and the function call path is:
rtw_set_802_11_bssid(acquire the spinlock)
rtw_disassoc_cmd
kzalloc(GFP_KERNEL) --> may sleep
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool and my code review.
The driver may sleep under a spinlock, and the function call path is:
rtw_surveydone_event_callback(acquire the spinlock)
rtw_createbss_cmd
kzalloc(GFP_KERNEL) --> may sleep
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool and my code review.
The driver may sleep under a spinlock, and the function call path is:
vt6655_suspend (acquire the spinlock)
pci_set_power_state
__pci_start_power_transition (drivers/pci/pci.c)
msleep --> may sleep
To fix it, pci_set_power_state is called without having a spinlock.
This bug is found by my static analysis tool and my code review.
The original code only took into consideration the largest header
possible after the IB_BTH_BYTES. This was incorrect, as the largest
possible header size is the largest possible combination of headers we
might run into. The new code accounts for all possible headers in the
largest possible combination and subtracts that from the MTU to make
sure that all packets will fit on the wire.
Link: https://www.spinics.net/lists/linux-rdma/msg54558.html Fixes: 3c86aa70bf67 ("RDMA/cm: Add RDMA CM support for IBoE devices") Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Daniel Jurgens <danielj@mellanox.com> Reported-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reshaping a fully degraded raid5/raid6 to a larger
nubmer of devices, the new device(s) are not in-sync
and so that can make the newly grown stripe appear to be
"failed".
To avoid this, we set the R5_Expanded flag to say "Even though
this device is not fully in-sync, this block is safe so
don't treat the device as failed for this stripe".
This flag is set for data devices, not not for parity devices.
Consequently, if you have a RAID6 with two devices that are partly
recovered and a spare, and start a reshape to include the spare,
then when the reshape gets past the point where the recovery was
up to, it will think the stripes are failed and will get into
an infinite loop, failing to make progress.
So when contructing parity on an EXPAND_READY stripe,
set R5_Expanded.
drivers/pinctrl/pinctrl-adi2.c: In function 'port_setup':
>> drivers/pinctrl/pinctrl-adi2.c:221:21: error: dereferencing
pointer to incomplete type 'struct gpio_port_t'
writew(readw(®s->port_fer) & ~BIT(offset),
^~
drivers/pinctrl/pinctrl-adi2.c: In function 'adi_gpio_ack_irq':
>> drivers/pinctrl/pinctrl-adi2.c:266:18: error: dereferencing
pointer to incomplete type 'struct bfin_pint_regs'
if (readl(®s->invert_set) & pintbit)
^~
It seems the driver need to include <asm/gpio.h> and <asm/irq.h>
to compile.
The Blackfin architecture was re-defining the Kconfig
PINCTRL symbol which is not OK, so replaced this with
PINCTRL_BLACKFIN_ADI2 which selects PINCTRL and PINCTRL_ADI2
just like most arches do.
Further, the old GPIO driver symbol GPIO_ADI was possible to
select at the same time as selecting PINCTRL. This was not
working because the arch-local <asm/gpio.h> header contains
an explicit #ifndef PINCTRL clause making compilation break
if you combine them. The same is true for DEBUG_MMRS.
Make sure the ADI2 pinctrl driver is not selected at the same
time as the old GPIO implementation. (This should be converted
to use gpiolib or pincontrol and move to drivers/...) Also make
sure the old GPIO_ADI driver or DEBUG_MMRS is not selected at
the same time as the new PINCTRL implementation, and only make
PINCTRL_ADI2 selectable for the Blackfin families that actually
have it.
This way it is still possible to add e.g. I2C-based pin
control expanders on the Blackfin.
When babble condition happens, the musb controller might automatically
turns off VBUS. On DA8xx platform, the controller generates drvvbus
interrupt for turning off VBUS along with the babble interrupt.
In this case, we should handle the babble interrupt first and recover
from the babble condition.
This change ignores the drvvbus interrupt if babble interrupt is also
generated at the same time, so the babble recovery routine works
properly.
Signed-off-by: Bin Liu <b-liu@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After rmmod 8250.ko
tty_kref_put starts kwork (release_one_tty) to release proc interface
oops when accessing driver->driver_name in proc_tty_unregister_driver
Use jprobe, found driver->driver_name point to 8250.ko
static static struct uart_driver serial8250_reg
.driver_name= serial,
Use name in proc_dir_entry instead of driver->driver_name to fix oops
In the hv-24x7 code there is a function memord() which tries to
implement a sort function return -1, 0, 1. However one of the
conditions is incorrect, such that it can never be true, because we
will have already returned.
I don't believe there is a bug in practice though, because the
comparisons are an optimisation prior to calling memcmp().
Fix it by swapping the second comparision, so it can be true.
Reported-by: David Binderman <dcb314@hotmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleans up a lot of warnings when unloading the driver.
A current example of the stack trace starts with:
[ 142.570715] sysfs group 'power' not found for kobject 'port-5:0'
There can be hundreds of these messages during a driver unload.
I am resubmitting this patch on behalf of Martin Wilck with his
permission.
His original patch can be found here:
https://www.spinics.net/lists/linux-scsi/msg102085.html
This patch did not help until Hannes's
commit 9441284fbc39 ("scsi-fixup-kernel-warning-during-rmmod")
was applied to the kernel.
---------------------------
Original patch description:
---------------------------
Unloading the hpsa driver causes warnings
[ 1063.793652] WARNING: CPU: 1 PID: 4850 at ../fs/sysfs/group.c:237 device_del+0x54/0x240()
[ 1063.793659] sysfs group ffffffff81cf21a0 not found for kobject 'port-2:0'
with two different stacks:
1)
[ 1063.793774] [<ffffffff81448af4>] device_del+0x54/0x240
[ 1063.793780] [<ffffffff8145178a>] transport_remove_classdev+0x4a/0x60
[ 1063.793784] [<ffffffff81451216>] attribute_container_device_trigger+0xa6/0xb0
[ 1063.793802] [<ffffffffa0105d46>] sas_port_delete+0x126/0x160 [scsi_transport_sas]
[ 1063.793819] [<ffffffffa036ebcc>] hpsa_free_sas_port+0x3c/0x70 [hpsa]
This is caused by the fact that host device hostX is deleted before the
SAS transport devices hostX/port-a:b.
This patch fixes this by reverting the order of device deletions.
Tested-by: Don Brace <don.brace@microsemi.com> Reviewed-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin Wilck <mwilck@suse.de> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I am resubmitting this patch on behalf of Martin Wilck with his
permission.
The original patch can be found here:
https://www.spinics.net/lists/linux-scsi/msg102083.html
This patch did not help until Hannes's
commit 9441284fbc39 ("scsi-fixup-kernel-warning-during-rmmod")
was applied to the kernel.
--------------------------------------
Original patch description from Martin:
--------------------------------------
When the hpsa module is unloaded using rmmod, dangling
symlinks remain under /sys/class/sas_phy. Fix this by
calling sas_phy_delete() rather than sas_phy_free (which,
according to comments, should not be called for PHYs that
have been set up successfully, anyway).
Tested-by: Don Brace <don.brace@microsemi.com> Reviewed-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin Wilck <mwilck@suse.de> Signed-off-by: Don Brace <don.brace@microsemi.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When removing a device, for example a VF being removed due to SR-IOV
teardown, a "soft" hot-unplug via 'echo 1 > remove' in sysfs, or an actual
hot-unplug, we first remove the procfs and sysfs attributes for the device
before attempting to release the device from any driver bound to it.
Unbinding the driver from the device can take time. The device might need
to write out data or it might be actively in use. If it's in use by
userspace through a vfio driver, the unbind might block until the user
releases the device. This leads to a potentially non-trivial amount of
time where the device exists, but we've torn down the interfaces that
userspace uses to examine devices, for instance lspci might generate this
sort of error:
pcilib: Cannot open /sys/bus/pci/devices/0000:01:0a.3/config
lspci: Unable to read the standard configuration space header of device 0000:01:0a.3
We don't seem to have any dependence on this teardown ordering in the
kernel, so let's unbind the driver first, which is also more symmetric with
the instantiation of the device in pci_bus_add_device().
There was one spot in xfs_bmap_add_extent_unwritten_real that didn't use the
passed in new extent state but always converted to normal, leading to wrong
behavior when converting from normal to unwritten.
Only found by code inspection, it seems like this code path to move partial
extent from written to unwritten while merging it with the next extent is
rarely exercised.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible for mkfs to format very small filesystems with too
small of an internal log with respect to the various minimum size
and block count requirements. If this occurs when the log happens to
be smaller than the scan window used for cycle verification and the
scan wraps the end of the log, the start_blk calculation in
xlog_find_head() underflows and leads to an attempt to scan an
invalid range of log blocks. This results in log recovery failure
and a failed mount.
Since there may be filesystems out in the wild with this kind of
geometry, we cannot simply refuse to mount. Instead, cap the scan
window for cycle verification to the size of the physical log. This
ensures that the cycle verification proceeds as expected when the
scan wraps the end of the log.
Reported-by: Zorro Lang <zlang@redhat.com> Signed-off-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
l2tp_tunnel_delete does not return anything since commit 62b982eeb458
("l2tp: fix race condition in l2tp_tunnel_delete"). But call sites of
l2tp_tunnel_delete still do casts to void to avoid unused return value
warnings.
Kill these now useless casts.
Signed-off-by: Jiri Slaby <jslaby@suse.cz> Cc: Sabrina Dubroca <sd@queasysnail.net> Cc: Guillaume Nault <g.nault@alphalink.fr> Cc: David S. Miller <davem@davemloft.net> Cc: netdev@vger.kernel.org Acked-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For kref_get_unless_zero to protect against lookup vs free races we need
to use it in all places where we aren't guaranteed to already hold a
reference. There is no such guarantee in nvme_find_get_ns, so switch to
kref_get_unless_zero in this function.
Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Reviewed-by: Hannes Reinecke <hare@suse.com> Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added support for HP ProBook 440 G4 laptops by including the accelerometer
orientation quirk for that device. Testing was performed based on the
axis orientation guidelines here:
https://www.kernel.org/doc/Documentation/misc-devices/lis3lv02d
which states "If the left side is elevated, X increases (becomes positive)".
When tested, on lifting the left edge, x values became increasingly negative
thus indicating an inverted x-axis on the installed lis3lv02d chip.
This was compensated by adding an entry for this device in hp_accel.c
specifying the quirk as x_inverted. The patch was tested on a
ProBook 440 G4 device and x-axis as well as y and z-axis values are now
generated as per spec.
Upon upgrading to binutils 2.27, we found that our lz4 and gzip
compressed kernel images were significantly larger, resulting is 10ms
boot time regressions.
As noted by Rahul:
"aarch64 binaries uses RELA relocations, where each relocation entry
includes an addend value. This is similar to x86_64. On x86_64, the
addend values are also stored at the relocation offset for relative
relocations. This is an optimization: in the case where code does not
need to be relocated, the loader can simply skip processing relative
relocations. In binutils-2.25, both bfd and gold linkers did this for
x86_64, but only the gold linker did this for aarch64. The kernel build
here is using the bfd linker, which stored zeroes at the relocation
offsets for relative relocations. Since a set of zeroes compresses
better than a set of non-zero addend values, this behavior was resulting
in much better lz4 compression.
The bfd linker in binutils-2.27 is now storing the actual addend values
at the relocation offsets. The behavior is now consistent with what it
does for x86_64 and what gold linker does for both architectures. The
change happened in this upstream commit:
https://sourceware.org/git/?p=binutils-gdb.git;a=commit;h=1f56df9d0d5ad89806c24e71f296576d82344613
Since a bunch of zeroes got replaced by non-zero addend values, we see
the side effect of lz4 compressed image being a bit bigger.
To get the old behavior from the bfd linker, "--no-apply-dynamic-relocs"
flag can be used:
$ LDFLAGS="--no-apply-dynamic-relocs" make
With this flag, the compressed image size is back to what it was with
binutils-2.25.
If the kernel is using ASLR, there aren't additional runtime costs to
--no-apply-dynamic-relocs, as the relocations will need to be applied
again anyway after the kernel is relocated to a random address.
If the kernel is not using ASLR, then presumably the current default
behavior of the linker is better. Since the static linker performed the
dynamic relocs, and the kernel is not moved to a different address at
load time, it can skip applying the relocations all over again."
Some measurements:
$ ld -v
GNU ld (binutils-2.25-f3d35cf6) 2.25.51.20141117
^
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng 300652760 Oct 26 11:57 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng 16932627 Oct 26 11:57 Image.lz4-dtb
$ ld -v
GNU ld (binutils-2.27-53dd00a1) 2.27.0.20170315
^
pre patch:
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng 300376208 Oct 26 11:43 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng 18159474 Oct 26 11:43 Image.lz4-dtb
post patch:
$ ls -l vmlinux
-rwxr-x--- 1 ndesaulniers eng 300376208 Oct 26 12:06 vmlinux
$ ls -l Image.lz4-dtb
-rw-r----- 1 ndesaulniers eng 16932466 Oct 26 12:06 Image.lz4-dtb
By Siqi's measurement w/ gzip:
binutils 2.27 with this patch (with --no-apply-dynamic-relocs):
Image 41535488
Image.gz 13404067
binutils 2.27 without this patch (without --no-apply-dynamic-relocs):
Image 41535488
Image.gz 14125516
Any compression scheme should be able to get better results from the
longer runs of zeros, not just GZIP and LZ4.
10ms boot time savings isn't anything to get excited about, but users of
arm64+compression+bfd-2.27 should not have to pay a penalty for no
runtime improvement.
Reported-by: Gopinath Elanchezhian <gelanchezhian@google.com> Reported-by: Sindhuri Pentyala <spentyala@google.com> Reported-by: Wei Wang <wvw@google.com> Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Suggested-by: Rahul Chaudhry <rahulchaudhry@google.com> Suggested-by: Siqi Lin <siqilin@google.com> Suggested-by: Stephen Hines <srhines@google.com> Signed-off-by: Nick Desaulniers <ndesaulniers@google.com> Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[will: added comment to Makefile] Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__subn_get_opa_portinfo stores value returned by hfi1_get_ib_cfg() as
operational vls. hfi1_get_ib_cfg() returns vls_operational field in
hfi1_pportdata. The problem with this is that the value is always equal
to vls_supported field in hfi1_pportdata.
The logic to calculate operational_vls is to set value passed by FM
(in __subn_set_opa_portinfo routine). If no value is passed then
default value is stored in operational_vls.
Field actual_vls_operational is calculated on the basis of buffer
control table. Hence, modifying hfi1_get_ib_cfg() to return
actual_operational_vls when used with HFI1_IB_CFG_OP_VLS parameter
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com> Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Patel Jay P <jay.p.patel@intel.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by: Doug Ledford <dledford@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, Cache missed IOs are identified by s->cache_miss, but actually,
there are many situations that missed IOs are not assigned a value for
s->cache_miss in cached_dev_cache_miss(), for example, a bypassed IO
(s->iop.bypass = 1), or the cache_bio allocate failed. In these situations,
it will go to out_put or out_submit, and s->cache_miss is null, which leads
bch_mark_cache_accounting() to treat this IO as a hit IO.
mutex_destroy does nothing most of time, but it's better to call
it to make the code future proof and it also has some meaning
for like mutex debug.
As Coly pointed out in a previous review, bcache_exit() may not be
able to handle all the references properly if userspace registers
cache and backing devices right before bch_debug_init runs and
bch_debug_init failes later. So not exposing userspace interface
until everything is ready to avoid that issue.
Signed-off-by: Liang Chen <liangchen.linux@gmail.com> Reviewed-by: Michael Lyle <mlyle@lyle.org> Reviewed-by: Coly Li <colyli@suse.de> Reviewed-by: Eric Wheeler <bcache@linux.ewheeler.net> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a deadlock caused when the jdata flag is set for
inodes that are already on the ordered write list. Since it is
on the ordered write list, log_flush calls gfs2_ordered_write which
calls filemap_fdatawrite. But since the inode had the jdata flag
set, that calls gfs2_jdata_writepages, which tries to start a new
transaction. A new transaction cannot be started because it tries
to acquire the log_flush rwsem which is already locked by the log
flush operation.
The bottom line is: We cannot switch an inode from ordered to jdata
until we eliminate any ordered data pages (via log flush) or any
log_flush operation afterward will create the circular dependency
above. So we need to flush the log before setting the diskflags to
switch the file mode, then we need to remove the inode from the
ordered writes list.
Before this patch, the log flush was done for jdata->ordered, but
that's wrong. If we're going from jdata to ordered, we don't need
to call gfs2_log_flush because the call to filemap_fdatawrite will
do it for us:
This patch modifies function do_gfs2_set_flags so that if a file
has its jdata flag set, and it's already on the ordered write list,
the log will be flushed and it will be removed from the list
before setting the flag.
Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Acked-by: Abhijith Das <adas@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The scsi_debug driver incorrectly suggests there is an error with the
SCSI WRITE SAME command when the number_of_logical_blocks is greater
than 1. It will also suggest there is an error when NDOB
(no data-out buffer) is set and the number_of_logical_blocks is
greater than 0. Both are valid, fix.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a particular situation when the cooling device is cpufreq and the heat
dissipation is not efficient enough where the temperature increases little by
little until reaching the critical threshold and leading to a SoC reset.
The behavior is reproducible on a hikey6220 with bad heat dissipation (eg.
stacked with other boards).
Running a simple C program doing while(1); for each CPU of the SoC makes the
temperature to reach the passive regulation trip point and ends up to the
maximum allowed temperature followed by a reset.
This issue has been also reported by running the libhugetlbfs test suite.
What is observed is a ping pong between two cpu frequencies, 1.2GHz and 900MHz
while the temperature continues to grow.
It appears the step wise governor calls get_target_state() the first time with
the throttle set to true and the trend to 'raising'. The code selects logically
the next state, so the cpu frequency decreases from 1.2GHz to 900MHz, so far so
good. The temperature decreases immediately but still stays greater than the
trip point, then get_target_state() is called again, this time with the
throttle set to true *and* the trend to 'dropping'. From there the algorithm
assumes we have to step down the state and the cpu frequency jumps back to
1.2GHz. But the temperature is still higher than the trip point, so
get_target_state() is called with throttle=1 and trend='raising' again, we jump
to 900MHz, then get_target_state() is called with throttle=1 and
trend='dropping', we jump to 1.2GHz, etc ... but the temperature does not
stabilizes and continues to increase.
In this situation the temperature continues to increase while the trend is
oscillating between 'dropping' and 'raising'. We need to keep the current state
untouched if the throttle is set, so the temperature can decrease or a higher
state could be selected, thus preventing this oscillation.
Keeping the next_target untouched when 'throttle' is true at 'dropping' time
fixes the issue.
The following traces show the governor does not change the next state if
trend==2 (dropping) and throttle==1.
After a while, if the temperature continues to increase, the next state becomes
2 which is 720MHz on the hikey. That results in the temperature stabilizing
around the trip point.
IOW, this change is needed to keep the state for a cooling device if the
temperature trend is oscillating while the temperature increases slightly.
Without this change, the situation above leads to a catastrophic crash by a
hardware reset on hikey. This issue has been reported to happen on an OMAP
dra7xx also.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Cc: Keerthy <j-keerthy@ti.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Leo Yan <leo.yan@linaro.org> Tested-by: Keerthy <j-keerthy@ti.com> Reviewed-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Eduardo Valentin <edubezval@gmail.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mutex_destroy only makes sense when enable DEBUG_MUTEX. For the
good readbility, it's better to invoke it in exit func when the init
func invokes mutex_init.
Signed-off-by: Gao Feng <gfree.wind@vip.163.com> Acked-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clock cs_atb_syspll is pll used for coresight trace bus; when clock
cs_atb_syspll is disabled and operates its child clock node cs_atb
results in system hang. So mark clock cs_atb_syspll as critical to
keep it enabled.
Cc: Guodong Xu <guodong.xu@linaro.org> Cc: Zhangfei Gao <zhangfei.gao@linaro.org> Cc: Haojian Zhuang <haojian.zhuang@linaro.org> Signed-off-by: Leo Yan <leo.yan@linaro.org> Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1504226835-2115-2-git-send-email-leo.yan@linaro.org Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That's because hdmi_isfr's parent, video_27m, is not correctly ungated.
As explained in commit 5ccc248cc537 ("ARM: imx6q: clk: Add support for
mipi_core_cfg clock as a shared clock gate"), video_27m is gated by
CCM_CCGR3[CG8].
On i.MX6 SoCs with VPU, the hdmi is working thanks to the
CCM_CMEOR[mod_en_ov_vpu] bit which makes the video_27m ungated whatever
is in CCM_CCGR3[CG8]. The issue can be reproduced by setting
CCMEOR[mod_en_ov_vpu] to 0.
Make the HDMI work in every case by setting hdmi_isfr's parent to
mipi_core_cfg.
Since the previous setup always sets the PLL using crystal 26MHz, this
doesn't always happen in every MediaTek platform. So the patch added
flexibility for assigning extra member for determining the PLL source
clock.
Signed-off-by: Chen Zhong <chen.zhong@mediatek.com> Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_calc_vm_trans() does not handle the situation when some of the passed
flags are 0 (which can happen if these VM flags do not make sense for
the architecture). Improve the _calc_vm_trans() macro to return 0 in
such situation. Since all passed flags are constant, this does not add
any runtime overhead.
Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the way the length of the buffers used for
encryption / decryption are computed.
For e.g. in case of encryption, input buffer does not contain
an authentication tag.
Signed-off-by: Robert Baronescu <robert.baronescu@nxp.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the PMU driver is built as a module, the perf expects the
pmu->module to be valid, so that the driver is prevented from
being unloaded while it is in use. Fix the CCN pmu driver to
fill in this field.
Fixes: a33b0daab73a0 ("bus: ARM CCN PMU driver") Cc: Pawel Moll <pawel.moll@arm.com> Cc: Will Deacon <will.deacon@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by: Will Deacon <will.deacon@arm.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On truncate down, if new size is not block size aligned, we zero the
rest of block to avoid exposing stale data to user, and
iomap_truncate_page() skips zeroing if the range is already in
unwritten state or a hole. Then we writeback from on-disk i_size to
the new size if this range hasn't been written to disk yet, and
truncate page cache beyond new EOF and set in-core i_size.
The problem is that we could write data between di_size and newsize
before removing the page cache beyond newsize, as the extents may
still be in unwritten state right after a buffer write. As such, the
page of data that newsize lies in has not been zeroed by page cache
invalidation before it is written, and xfs_do_writepage() hasn't
triggered it's "zero data beyond EOF" case because we haven't
updated in-core i_size yet. Then a subsequent mmap read could see
non-zeros past EOF.
I occasionally see this in fsx runs in fstests generic/112, a
simplified fsx operation sequence is like (assuming 4k block size
xfs):
where fallocate allocates unwritten extent but doesn't update
i_size, buffer write populates the page cache and extent is still
unwritten, truncate skips zeroing page past new EOF and writes the
page to disk, punch_hole invalidates the page cache, at last mapread
reads the block back and sees non-zero beyond EOF.
Fix it by moving truncate_setsize() to before writeback so the page
cache invalidation zeros the partial page at the new EOF. This also
triggers "zero data beyond EOF" in xfs_do_writepage() at writeback
time, because newsize has been set and page straddles the newsize.
Also fixed the wrong 'end' param of filemap_write_and_wait_range()
call while we're at it, the 'end' is inclusive and should be
'newsize - 1'.
Suggested-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Eryu Guan <eguan@redhat.com> Acked-by: Dave Chinner <dchinner@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MD's rdev_set_badblocks() expects that badblocks_set() returns 1 if
badblocks are disabled, otherwise, rdev_set_badblocks() will record
superblock changes and return success in that case and md will fail to
report an IO error which it should.
This bug has existed since badblocks were introduced in commit 9e0e252a048b ("badblocks: Add core badblock management code").
Signed-off-by: Liu Bo <bo.li.liu@oracle.com> Acked-by: Guoqing Jiang <gqjiang@suse.com> Signed-off-by: Shaohua Li <shli@fb.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function fd_execute_unmap() in target_core_file.c calles
ret = file->f_op->fallocate(file, mode, pos, len);
Some filesystems implement fallocate() to return error if
length is zero (e.g. btrfs) but according to SCSI Block
Commands spec UNMAP should return success for zero length.
Signed-off-by: Jiang Yi <jiangyilism@gmail.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For PUNIT device, ISPDRIVER_IPC and GTDDRIVER_IPC resources are not
mandatory. So when PMC IPC driver creates a PUNIT device, if these
resources are not available then it creates dummy resource entries for
these missing resources. But during PUNIT device probe, doing ioremap on
these dummy resources generates following warning messages.
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
intel_punit_ipc: can't request region for resource [mem 0x00000000]
This patch fixes this issue by adding extra check for resource size
before performing ioremap operation.
The current code checks the completion map to look for the first token
that is complete. In some cases, a completion can come in but the
token can still be on lease to the caller processing the completion.
If this completed but unreleased token is the first token found in the
bitmap by another tasks trying to acquire a token, then the
__test_and_set_bit call will fail since the token will still be on
lease. The acquisition will then fail with an EBUSY.
This patch reorganizes the acquisition code to look at the
opal_async_token_map for an unleased token. If the token has no lease
it must have no outstanding completions so we should never see an
EBUSY, unless we have leased out too many tokens. Since
opal_async_get_token_inrerruptible is protected by a semaphore, we
will practically never see EBUSY anymore.
Fixes: 8d7248232208 ("powerpc/powernv: Infrastructure to support OPAL async completion") Signed-off-by: William A. Kennington III <wak@google.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Information about ipvs in different network namespace can be seen via procfs.
How to reproduce:
# ip netns add ns01
# ip netns add ns02
# ip netns exec ns01 ip a add dev lo 127.0.0.1/8
# ip netns exec ns02 ip a add dev lo 127.0.0.1/8
# ip netns exec ns01 ipvsadm -A -t 10.1.1.1:80
# ip netns exec ns02 ipvsadm -A -t 10.1.1.2:80
The ipvsadm displays information about its own network namespace only.
# ip netns exec ns01 ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 10.1.1.1:80 wlc
# ip netns exec ns02 ipvsadm -Ln
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 10.1.1.2:80 wlc
But I can see information about other network namespace via procfs.
# ip netns exec ns01 cat /proc/net/ip_vs
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 0A010101:0050 wlc
TCP 0A010102:0050 wlc
# ip netns exec ns02 cat /proc/net/ip_vs
IP Virtual Server version 1.2.1 (size=4096)
Prot LocalAddress:Port Scheduler Flags
-> RemoteAddress:Port Forward Weight ActiveConn InActConn
TCP 0A010102:0050 wlc
There exist two Mediatek iommu drivers for the two different
generations of the device. But both drivers have the same name
"mtk-iommu". This breaks the registration of the second driver:
Error: Driver 'mtk-iommu' is already registered, aborting...
Fix this by changing the name for first generation to
"mtk-iommu-v1".
Fixes: b17336c55d89 ("iommu/mediatek: add support for mtk iommu generation one HW") Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One can ask more buses to be reserved for hotplug bridges by passing
pci=hpbussize=N in the kernel command line. If the parent bus does not
have enough bus space available we incorrectly create child bus with the
requested number of subordinate buses.
In the example below hpbussize is set to one more than we have available
buses in the root port:
pci 0000:07:00.0: [8086:1578] type 01 class 0x060400
pci 0000:07:00.0: scanning [bus 00-00] behind bridge, pass 0
pci 0000:07:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:07:00.0: scanning [bus 00-00] behind bridge, pass 1
pci_bus 0000:08: busn_res: can not insert [bus 08-ff] under [bus 07-3f] (conflicts with (null) [bus 07-3f])
pci_bus 0000:08: scanning bus
...
pci_bus 0000:0a: bus scan returning with max=40
pci_bus 0000:0a: busn_res: [bus 0a-ff] end is updated to 40
pci_bus 0000:0a: [bus 0a-40] partially hidden behind bridge 0000:07 [bus 07-3f]
pci_bus 0000:08: bus scan returning with max=40
pci_bus 0000:08: busn_res: [bus 08-ff] end is updated to 40
Instead of allowing this, limit the subordinate number to be less than or
equal the maximum subordinate number allocated for the parent bus (if it
has any).
The call to /proc/cpuinfo in turn calls cpufreq_quick_get() which
returns the last frequency requested by the kernel, but may not
reflect the actual frequency the processor is running at. This patch
makes a call to cpufreq_get() instead which returns the current
frequency reported by the hardware.
PCIe PME and native hotplug share the same interrupt number, so hotplug
interrupts are also processed by PME. In some cases, e.g., a Link Down
interrupt, a device may be present but unreachable, so when we try to
read its Root Status register, the read fails and we get all ones data
(0xffffffff).
Previously, we interpreted that data as PCI_EXP_RTSTA_PME being set, i.e.,
"some device has asserted PME," so we scheduled pcie_pme_work_fn(). This
caused an infinite loop because pcie_pme_work_fn() tried to handle PME
requests until PCI_EXP_RTSTA_PME is cleared, but with the link down,
PCI_EXP_RTSTA_PME can't be cleared.
Check for the invalid 0xffffffff data everywhere we read the Root Status
register.
1469d17dd341 ("PCI: pciehp: Handle invalid data when reading from
non-existent devices") added similar checks in the hotplug driver.
Signed-off-by: Qiang Zheng <zhengqiang10@huawei.com>
[bhelgaas: changelog, also check in pcie_pme_work_fn(), use "~0" to follow
other similar checks] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The used 0x1f mask is only valid for am335x family of SoC, different family
using this type of crossbar might have different number of electable
events. In case of am43xx family 0x3f mask should have been used for
example.
Instead of trying to handle each family's mask, just use u8 type to store
the mux value since the event offsets are aligned to byte offset.
Fixes: 42dbdcc6bf965 ("dmaengine: ti-dma-crossbar: Add support for crossbar on AM33xx/AM43xx") Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the loop that adds the uuid_module to the uuid_list list, allocated
memory is not properly freed in the error path free uuid_list whenever
any of the memory allocation in the loop fails to avoid memory leak.
While usb_control_msg function expects timeout in miliseconds, a value
of HZ is used. Replace it with USB_CTRL_GET_TIMEOUT and also fix error
message which looks like:
udlfb: Read EDID byte 78 failed err ffffff92
as error is either negative errno or number of bytes transferred use %d
format specifier.
Returned EDID is in second byte, so return error when less than two bytes
are received.
Indeed, control_mac_modes[] has only 20 elements, while VMODE_MAX is 22,
which may lead to an out of bounds read when parsing vmode commandline
options.
The bug was introduced in v2.4.5.6, when 2 new modes were added to
macmodes.h, but control_mac_modes[] wasn't updated:
Fixes: 535a61777f44e ("sfc: suppress handled MCDI failures when changing the MAC address") Signed-off-by: Bert Kenward <bkenward@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Revert: dc6db24d2476 ("x86/acpi: Set persistent cpuid <-> nodeid mapping when booting")
The mapping of "cpuid <-> nodeid" is established at boot time via ACPI
tables to keep associations of workqueues and other node related items
consistent across cpu hotplug.
But, ACPI tables are unreliable and failures with that boot time mapping
have been reported on machines where the ACPI table and the physical
information which is retrieved at actual hotplug is inconsistent.
Revert the mapping implementation so it can be replaced with a less error
prone approach.
1. core_alua_do_transition_tg_pt could have read
tg_pt_gp_alua_access_state and gone into this if chunk:
if (!explicit &&
atomic_read(&tg_pt_gp->tg_pt_gp_alua_access_state) ==
ALUA_ACCESS_STATE_TRANSITION) {
and then core_alua_do_transition_tg_pt_work could update the
state. core_alua_do_transition_tg_pt would then only set
tg_pt_gp_alua_pending_state and the tg_pt_gp_alua_access_state would
not get updated with the second calls state.
2. core_alua_do_transition_tg_pt could be setting
tg_pt_gp_transition_complete while the tg_pt_gp_transition_work
is already completing. core_alua_do_transition_tg_pt then waits on the
completion that will never be called.
To handle these issues, we just call flush_work which will return when
core_alua_do_transition_tg_pt_work has completed so there is no need
to do the complete/wait. And, if core_alua_do_transition_tg_pt_work
was running, instead of trying to sneak in the state change, we just
schedule up another core_alua_do_transition_tg_pt_work call.
Note that this does not handle a possible race where there are multiple
threads call core_alua_do_transition_tg_pt at the same time. I think
we need a mutex in target_tg_pt_gp_alua_access_state_store.
Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The implicit transition time tells initiators the min time
to wait before timing out a transition. We currently schedule
the transition to occur in tg_pt_gp_implicit_trans_secs
seconds so there is no room for delays. If
core_alua_do_transition_tg_pt_work->core_alua_update_tpg_primary_metadata
needs to write out info to a remote file, then the initiator can
easily time out the operation.
Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If tcmu-runner is processing a STPG and needs to change the kernel's
ALUA state then we cannot use the same work queue for task management
requests and ALUA transitions, because we could deadlock. The problem
occurs when a STPG times out before tcmu-runner is able to
call into target_tg_pt_gp_alua_access_state_store->
core_alua_do_port_transition -> core_alua_do_transition_tg_pt ->
queue_work. In this case, the tmr is on the work queue waiting for
the STPG to complete, but the STPG transition is now queued behind
the waiting tmr.
Note:
This bug will also be fixed by this patch:
http://www.spinics.net/lists/target-devel/msg14560.html
which switches the tmr code to use the system workqueues.
For both, I am not sure if we need a dedicated workqueue since
it is not a performance path and I do not think we need WQ_MEM_RECLAIM
to make forward progress to free up memory like the block layer does.
Signed-off-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a story about 4 distinct (and very old) btrfs bugs.
Commit c8b978188c ("Btrfs: Add zlib compression support") added
three data corruption bugs for inline extents (bugs #1-3).
Commit 93c82d5750 ("Btrfs: zero page past end of inline file items")
fixed bug #1: uncompressed inline extents followed by a hole and more
extents could get non-zero data in the hole as they were read. The fix
was to add a memset in btrfs_get_extent to zero out the hole.
Commit 166ae5a418 ("btrfs: fix inline compressed read err corruption")
fixed bug #2: compressed inline extents which contained non-zero bytes
might be replaced with zero bytes in some cases. This patch removed an
unhelpful memset from uncompress_inline, but the case where memset is
required was missed.
There is also a memset in the decompression code, but this only covers
decompressed data that is shorter than the ram_bytes from the extent
ref record. This memset doesn't cover the region between the end of the
decompressed data and the end of the page. It has also moved around a
few times over the years, so there's no single patch to refer to.
This patch fixes bug #3: compressed inline extents followed by a hole
and more extents could get non-zero data in the hole as they were read
(i.e. bug #3 is the same as bug #1, but s/uncompressed/compressed/).
The fix is the same: zero out the hole in the compressed case too,
by putting a memset back in uncompress_inline, but this time with
correct parameters.
The last and oldest bug, bug #0, is the cause of the offending inline
extent/hole/extent pattern. Bug #0 is a subtle and mostly-harmless quirk
of behavior somewhere in the btrfs write code. In a few special cases,
an inline extent and hole are allowed to persist where they normally
would be combined with later extents in the file.
A fast reproducer for bug #0 is presented below. A few offending extents
are also created in the wild during large rsync transfers with the -S
flag. A Linux kernel build (git checkout; make allyesconfig; make -j8)
will produce a handful of offending files as well. Once an offending
file is created, it can present different content to userspace each
time it is read.
Bug #0 is at least 4 and possibly 8 years old. I verified every vX.Y
kernel back to v3.5 has this behavior. There are fossil records of this
bug's effects in commits all the way back to v2.6.32. I have no reason
to believe bug #0 wasn't present at the beginning of btrfs compression
support in v2.6.29, but I can't easily test kernels that old to be sure.
It is not clear whether bug #0 is worth fixing. A fix would likely
require injecting extra reads into currently write-only paths, and most
of the exceptional cases caused by bug #0 are already handled now.
Whether we like them or not, bug #0's inline extents followed by holes
are part of the btrfs de-facto disk format now, and we need to be able
to read them without data corruption or an infoleak. So enough about
bug #0, let's get back to bug #3 (this patch).
An example of on-disk structure leading to data corruption found in
the wild:
Different data appears in userspace during each read of the 11 bytes
between 4085 and 4096. The extent in item 63 is not long enough to
fill the first page of the file, so a memset is required to fill the
space between item 63 (ending at 4085) and item 64 (beginning at 4096)
with zero.
Here is a reproducer from Liu Bo, which demonstrates another method
of creating the same inline extent and hole pattern:
Using 'page_poison=on' kernel command line (or enable
CONFIG_PAGE_POISONING) run the following:
Currently client doesn't respect max sizes server returns in CREATE_SESSION.
nfs4_session_set_rwsize() gets called and server->rsize, server->wsize are 0
so they never get set to the sizes returned by the server.
Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel Compute Stick STCK1A8LFC and Weibu F3C platforms both
log 2 error messages during boot:
efi: requested map not found.
esrt: ESRT header is not in the memory map.
Searching the web, this seems to affect many other platforms too.
Since these messages are logged as errors, they appear on-screen during
the boot process even when using the "quiet" boot parameter used by
distros.
Demote the ESRT error to a warning so that it does not appear on-screen,
and delete the error logging from efi_mem_desc_lookup; both callsites
of that function log more specific messages upon failure.
Out of curiosity I looked closer at the Weibu F3C. There is no entry in
the UEFI-provided memory map which corresponds to the ESRT pointer, but
hacking the code to map it anyway, the ESRT does appear to be valid with
2 entries.
Signed-off-by: Daniel Drake <drake@endlessm.com> Cc: Matt Fleming <matt@codeblueprint.co.uk> Acked-by: Peter Jones <pjones@redhat.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current symbols__fixup_end() heuristic for the last entry in the rb
tree is suboptimal as it leads to not being able to recognize the symbol
in the call graph in a couple of corner cases, for example:
i) If the symbol has a start address (f.e. exposed via kallsyms)
that is at a page boundary, then the roundup(curr->start, 4096)
for the last entry will result in curr->start == curr->end with
a symbol length of zero.
ii) If the symbol has a start address that is shortly before a page
boundary, then also here, curr->end - curr->start will just be
very few bytes, where it's unrealistic that we could perform a
match against.
Instead, change the heuristic to roundup(curr->start, 4096) + 4096, so
that we can catch such corner cases and have a better chance to find
that specific symbol. It's still just best effort as the real end of the
symbol is unknown to us (and could even be at a larger offset than the
current range), but better than the current situation.
Alexei reported that he recently run into case i) with a JITed eBPF
program (these are all page aligned) as the last symbol which wasn't
properly shown in the call graph (while other eBPF program symbols in
the rb tree were displayed correctly). Since this is a generic issue,
lets try to improve the heuristic a bit.
tty_ldisc_ref_wait() checks tty->ldisc under tty->ldisc_sem.
But if ldisc==NULL it releases them sem and reloads
tty->ldisc without holding the sem. This is wrong and
can lead to returning non-NULL ldisc without protection.
If tty_ldisc_open() fails in tty_set_ldisc(), it tries to go back
to the old discipline or N_TTY. But that can fail as well, in such
case it panics. This is not a graceful way to handle OOM.
Leave ldisc==NULL if all attempts fail instead.
Also use existing tty_ldisc_reinit() helper function instead of
tty_ldisc_restore(). Also don't WARN/BUG in tty_ldisc_reinit()
if N_TTY fails, which would have the same net effect of bringing
kernel down on OOM. Instead print a single line message about
what has happened.
If we receive a BUSY packet for a call we think we've just completed, the
packet is handed off to the connection processor to deal with - but the
connection processor doesn't expect a BUSY packet and so flags a protocol
error.
Fix this by simply ignoring the BUSY packet for the moment.
The symptom of this may appear as a system call failing with EPROTO. This
may be triggered by pressing ctrl-C under some circumstances.
This comes about we abort calls due to interruption by a signal (which we
shouldn't do, but that's going to be a large fix and mostly in fs/afs/).
What happens is that we abort the call and may also abort follow up calls
too (this needs offloading somehoe). So we see a transmission of something
like the following sequence of packets:
DATA for call N
ABORT call N
DATA for call N+1
ABORT call N+1
in very quick succession on the same channel. However, the peer may have
deferred the processing of the ABORT from the call N to a background thread
and thus sees the DATA message from the call N+1 coming in before it has
cleared the channel. Thus it sends a BUSY packet[*].
[*] Note that some implementations (OpenAFS, for example) mark the BUSY
packet with one plus the callNumber of the call prior to call N.
Ordinarily, this would be call N, but there's no requirement for the
calls on a channel to be numbered strictly sequentially (the number is
required to increase).
This is wrong and means that the callNumber in the BUSY packet should
be ignored (it really ought to be N+1 since that's what it's in
response to).
Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alive tracking of nexthops can account for a link twice if the carrier
goes down followed by an admin down of the same link rendering multipath
routes useless. This is similar to 79099aab38c8 for UNREGISTER events and
DOWN events.
Fix by tracking number of alive nexthops in mpls_ifdown similar to the
logic in mpls_ifup. Checking the flags per nexthop once after all events
have been processed is simpler than trying to maintian a running count
through all event combinations.
Also, WRITE_ONCE is used instead of ACCESS_ONCE to set rt_nhn_alive
per a comment from checkpatch:
WARNING: Prefer WRITE_ONCE(<FOO>, <BAR>) over ACCESS_ONCE(<FOO>) = <BAR>
Fixes: c89359a42e2a4 ("mpls: support for dead routes") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Acked-by: Robert Shearman <rshearma@brocade.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
For such Hypervisors, there is a race condition between the VF's
shutdown method and its internal-error detection/reset thread.
The internal-error detection/reset thread (which runs every 5 seconds) also
detects a disabled comm channel. If the internal-error detection/reset
flow wins the race, we still get delays (while that flow tries repeatedly
to detect comm-channel recovery).
The cited commit fixed the command timeout problem when the
internal-error detection/reset flow loses the race.
This commit avoids the unneeded delays when the internal-error
detection/reset flow wins.
Fixes: d585df1c5ccf ("net/mlx4_core: Avoid command timeouts during VF driver device shutdown") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Reported-by: Simon Xiao <sixiao@microsoft.com> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When handling a new recv command, we grab a new rsp resource and
check for the queue state being live. In case the queue is not in
live state, we simply restore the rsp back to the free list. However
in this flow we didn't set rsp->queue yet, so we cannot dereference it.
Instead, make sure to initialize rsp->queue (and other rsp members)
as soon as possible so we won't reference uninitialized variables.
Fix the way in which a call that's in progress and being waited for is
aborted in the case that EINTR is detected. We should be sending
RX_USER_ABORT rather than RX_CALL_DEAD as the abort code.
Note that since the only two ways out of the loop are if the call completes
or if a signal happens, the kill-the-call clause after the loop has
finished can only happen in the case of EINTR. This means that we only
have one abort case to deal with, not two, and the "KWC" case can never
happen and so can be deleted.
Note further that simply aborting the call isn't necessarily the best thing
here since at this point: the request has been entirely sent and it's
likely the server will do the operation anyway - whether we abort it or
not. In future, we should punt the handling of the remainder of the call
off to a background thread.
Reported-by: Marc Dionne <marc.c.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(1) If a writeback has been partially flushed, then if we try and kill the
pages it contains, some of them may no longer be undergoing writeback
and end_page_writeback() will assert.
Fix this by checking to see whether the page in question is actually
undergoing writeback before ending that writeback.
(2) The loop that scans for pages to kill doesn't increase the first page
index, and so the loop may not terminate, but it will try to process
the same pages over and over again.
Fix this by increasing the first page index to one after the last page
we processed.
The inode timestamps should be set from the client time
in the status received from the server, rather than the
server time which is meant for internal server use.
Set AFS_SET_MTIME and populate the mtime for operations
that take an input status, such as file/dir creation
and StoreData. If an input time is not provided the
server will set the vnode times based on the current server
time.
In a situation where the server has some skew with the
client, this could lead to the client seeing a timestamp
in the future for a file that it just created or wrote.
Signed-off-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we receive a network error, a remote abort or a protocol error whilst
we're still transmitting data, make sure we return an appropriate error to
the caller rather than ESHUTDOWN or ECONNABORTED.
afs_fs_store_data() works out of the size of the write it's going to make,
but it uses 32-bit unsigned subtraction in one place that gets
automatically cast to loff_t.
However, if to < offset, then the number goes negative, but as the result
isn't signed, this doesn't get sign-extended to 64-bits when placed in a
loff_t.
get_seconds() returns real wall-clock seconds. On 32-bit systems
this value will overflow in year 2038 and beyond. This patch changes
afs_vnode record to use ktime_get_real_seconds() instead, for the
fields cb_expires and cb_expires_at.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_seconds() returns real wall-clock seconds. On 32-bit systems
this value will overflow in year 2038 and beyond. This patch changes
afs's vlocation record to use ktime_get_real_seconds() instead, for the
fields time_of_death and update_at.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Sasha Levin <alexander.levin@verizon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Servers may send a callback array that is the same size as
the FID array, or an empty array. If the callback count is
0, the code would attempt to read (fid_count * 12) bytes of
data, which would fail and result in an unmarshalling error.
This would lead to stale data for remotely modified files
or directories.
Store the callback array size in the internal afs_call
structure and use that to determine the amount of data to
read.
projects / linux-stable / log