Currently we check if the __ICE_PREPARED_FOR_RESET bit is set prior to
calling ice_prepare_for_reset in ice_reset_subtask(), but we aren't
checking that bit in ice_do_reset() before calling
ice_prepare_for_reset(). This is not consistent and can cause issues if
ice_prepare_for_reset() is called prior to ice_do_reset(). Fix this by
checking if the __ICE_PREPARED_FOR_RESET bit is set internal to
ice_prepare_for_reset().
Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The quiesce function calls cio_cancel_halt_clear() and if we
get an -EBUSY we go into a loop where we:
- wait for any interrupts
- flush all I/O in the workqueue
- retry cio_cancel_halt_clear
During the period where we are waiting for interrupts or
flushing all I/O, the channel subsystem could have completed
a halt/clear action and turned off the corresponding activity
control bits in the subchannel status word. This means the next
time we call cio_cancel_halt_clear(), we will again start by
calling cancel subchannel and so we can be stuck between calling
cancel and halt forever.
Rather than calling cio_cancel_halt_clear() immediately after
waiting, let's try to disable the subchannel. If we succeed in
disabling the subchannel then we know nothing else can happen
with the device.
Suggested-by: Eric Farman <farman@linux.ibm.com> Signed-off-by: Farhan Ali <alifm@linux.ibm.com>
Message-Id: <4d5a4b98ab1b41ac6131b5c36de18b76c5d66898.1555449329.git.alifm@linux.ibm.com> Reviewed-by: Eric Farman <farman@linux.ibm.com> Acked-by: Halil Pasic <pasic@linux.ibm.com> Signed-off-by: Cornelia Huck <cohuck@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current calculation for the video start delay in the current DSI driver
is that it is the total vertical size, minus the front porch and sync length,
plus 1. This equals to the active vertical size plus the back porch plus 1.
That 1 is coming in the Allwinner BSP from an variable that is set to 1.
However, if we look at the Allwinner BSP more closely, and especially in
the "legacy" code for the display (in drivers/video/sunxi/legacy/), we can
see that this variable is actually computed from the porches and the sync
minus 10, clamped between 8 and 100.
This fixes the start delay symptom we've seen on some panels (vblank
timeouts with vertical white stripes at the bottom of the panel).
After an event is sent, we try to copy it into the user buffer of the
first waiter in drm_read() and if the user buffer doesn't have enough
room we put it back onto the list. However, we didn't wake up any
subsequent waiter, so that event may sit on the list until either a new
vblank event is sent or a new waiter appears. Rare, but in the worst
case may lead to a stuck process.
The SND_SOC_DAVINCI_MCASP driver can use either edma or sdma as
a back-end, and it takes the presence of the respective dma engine
drivers in the configuration as an indication to which ones should be
built. However, this is flawed in multiple ways:
- With CONFIG_TI_EDMA=m and CONFIG_SND_SOC_DAVINCI_MCASP=y,
is enabled as =m, and we get a link error:
sound/soc/ti/davinci-mcasp.o: In function `davinci_mcasp_probe':
davinci-mcasp.c:(.text+0x930): undefined reference to `edma_pcm_platform_register'
- When CONFIG_SND_SOC_DAVINCI_MCASP=m has already been selected by
another driver, the same link error appears even if CONFIG_TI_EDMA
is disabled
There are possibly other issues here, but it seems that the only reasonable
solution is to always build both SND_SOC_TI_EDMA_PCM and
SND_SOC_TI_SDMA_PCM as a dependency here. Both are fairly small and
do not have any other compile-time dependencies, so the cost is
very small, and makes the configuration stage much more consistent.
Fixes: f2055e145f29 ("ASoC: ti: Merge davinci and omap directories") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Building with clang shows a variable that is only used by the
suspend/resume functions but defined outside of their #ifdef block:
sound/soc/ti/davinci-mcasp.c:48:12: error: variable 'context_regs' is not needed and will not be emitted
We commonly fix these by marking the PM functions as __maybe_unused,
but here that would grow the davinci_mcasp structure, so instead
add another #ifdef here.
Fixes: 1cc0c054f380 ("ASoC: davinci-mcasp: Convert the context save/restore to use array") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This fixes a bug for messages containing both zero length and
unidirectional xfers.
The function spi_map_msg will allocate dummy tx and/or rx buffers
for use with unidirectional transfers when the hardware can only do
a bidirectional transfer. That dummy buffer will be used in place
of a NULL buffer even when the xfer length is 0.
Then in the function __spi_map_msg, if he hardware can dma,
the zero length xfer will have spi_map_buf called on the dummy
buffer.
Eventually, __sg_alloc_table is called and returns -EINVAL
because nents == 0.
This fix prevents the error by not using the dummy buffer when
the xfer length is zero.
Signed-off-by: Chris Lesiak <chris.lesiak@licor.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: f6130be652d0 ("regulator: DA9055 regulator driver") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 4068e5182ada ("regulator: da9062: DA9062 regulator driver") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: c90456e36d9c ("regulator: pv88090: new regulator driver") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: e4ee831f949a ("regulator: Add WM831x DC-DC buck convertor support") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 99cf3af5e2d5 ("regulator: pv88080: new regulator driver") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 69ca3e58d178 ("regulator: da9063: Add Dialog DA9063 voltage regulators support.") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 1028a37daa14 ("regulator: da9211: new regulator driver") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: b59320cc5a5e ("regulator: lp8755: new driver for LP8755") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 71abd29057cb ("spi: imx: Add support for SPI Slave mode") added
an RX FIFO flush before start of a transfer. In slave mode, the master
may have sent more data than expected and this data will still be in the
RX FIFO at the start of the next transfer, and so needs to be flushed.
However, the code to do the flush was accidentally saving this data into
the previous transfer's RX buffer, clobbering the contents of whatever
followed that buffer.
Change it to empty the FIFO and throw away the data. Every one of the
RX functions for the different eCSPI versions and modes reads the RX
FIFO data using the same readl() call, so just use that, rather than
using the spi_imx->rx function pointer and making sure all the different
rx functions have a working "throw away" mode.
There is another issue, which affects master mode when switching from
DMA to PIO. There can be extra data in the RX FIFO which triggers this
flush code, causing memory corruption in the same manner. I don't know
why this data is unexpectedly in the FIFO. It's likely there is a
different bug or erratum responsible for that. But regardless of that,
I think this is proper fix the for bug at hand here.
Fixes: 71abd29057cb ("spi: imx: Add support for SPI Slave mode") Cc: Jiada Wang <jiada_wang@mentor.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Stefan Agner <stefan@agner.ch> Cc: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Trent Piepho <tpiepho@impinj.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: f307a7e9b7af ("regulator: pv88060: new regulator driver") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 3eb2c7ecb7ea ("regulator: Add LTC3589 support") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: 37b918a034fe ("regulator: Add LTC3676 support") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: d4d6b722e780 ("regulator: Add WM831x ISINK support") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The mutex for the regulator_dev must be controlled by the caller of
the regulator_notifier_call_chain(), as described in the comment
for that function.
Failure to mutex lock and unlock surrounding the notifier call results
in a kernel WARN_ON_ONCE() which will dump a backtrace for the
regulator_notifier_call_chain() when that function call is first made.
The mutex can be controlled using the regulator_lock/unlock() API.
Fixes: d1c6b4fe668b ("regulator: Add WM831x LDO support") Suggested-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the sequencer is reset after each SPI message since commit 880c6d114fd79a69 ("spi: rspi: Add support for Quad and Dual SPI
Transfers on QSPI"), it was never reset for the first message, thus
relying on reset state or bootloader settings.
Fix this by initializing it explicitly during configuration.
Fixes: 0b2182ddac4b8837 ("spi: add support for Renesas RSPI") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For HDMI pipelines, when the output gets disconnected the device
handling CEC needs to be notified. Instead of guessing which device that
would be (and sometimes getting it wrong), notify all devices in the
pipeline.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently dsi_display_init_dsi() calls dss_pll_enable() but it is not
paired with dss_pll_disable() in dsi_display_uninit_dsi(). This leaves
the DSS clocks enabled when the display is blanked wasting about extra
5mW of power while idle.
The clock that is left on by not calling dss_pll_disable() is
DSS_CLKCTRL bit 10 OPTFCLKEN_SYS_CLK that is the source clock for
DSI PLL.
We can fix this issue by by making the current dsi_pll_uninit() into
dsi_pll_disable(). This way we can just call dss_pll_disable() from
dsi_display_uninit_dsi() and the code becomes a bit easier to follow.
However, we need to also consider that DSI PLL can be muxed for DVI too
as pointed out by Tomi Valkeinen <tomi.valkeinen@ti.com>. In the DVI
case, we want to unconditionally disable the clocks. To get around this
issue, we separate out the DSI lane handling from dsi_pll_enable() and
dsi_pll_disable() as suggested by Tomi in an earlier experimental patch.
So we must only toggle the DSI regulator based on the vdds_dsi_enabled
flag from dsi_display_init_dsi() and dsi_display_uninit_dsi().
We need to make these two changes together to avoid breaking things
for DVI when fixing the DSI clock handling. And this all causes a
slight renumbering of the error path for dsi_display_init_dsi().
Suggested-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Writeback jobs are allocated when the WRITEBACK_FB_ID is set, and
deleted when the jobs complete. This results in both a memory leak of
the job and a leak of the framebuffer if the atomic commit returns
before the job is queued for processing, for instance if the atomic
check fails or if the commit runs in test-only mode.
Fix this by implementing the drm_writeback_cleanup_job() function and
calling it from __drm_atomic_helper_connector_destroy_state(). As
writeback jobs are removed from the state when they're queued for
processing, any job left in the state when the state gets destroyed
needs to be cleaned up.
The existing declaration of the drm_writeback_cleanup_job() function
without an implementation hints that this problem was considered, but
never addressed.
pch_alloc_dma_buf allocated tx, rx DMA buffers which can fail. Further,
these buffers are used without a check. The patch checks for these
failures and sends the error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
module.name will be allocated unconditionally when auditing load
module, and audit_log_start() can fail with other reasons, or
audit_log_exit maybe not called, caused module.name is not freed
so free module.name in audit_free_context and __audit_syscall_exit
Fixes: ca86cad7380e3 ("audit: log module name on init_module") Signed-off-by: Zhang Yu <zhangyu31@baidu.com> Signed-off-by: Li RongQing <lirongqing@baidu.com>
[PM: manual merge fixup in __audit_syscall_exit()] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When unloading the driver, mailbox commands may be sent without holding a
reference on the ndlp. By the time the mailbox command completes, the ndlp
may have reduced its ref counts and been freed. The problem was reported
by KASAN.
While unregistering due to driver unload, have the completion noop'd by
setting the ndlp context NULL'd. Due to the unload, no further action was
necessary. Also, while reviewing this path, the generic nulling of the
context after handling should be slightly moved.
Reported by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During debug, it was seen that the driver is issuing commands specific to
SLI3 on SLI4 devices. Although the adapter correctly rejected the command,
this should not be done.
Revise the code to stop sending these commands on a SLI4 adapter.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Two saa7146/hexium files contain a construct that causes a warning
when built with clang:
drivers/media/pci/saa7146/hexium_orion.c:210:12: error: stack frame size of 2272 bytes in function 'hexium_probe'
[-Werror,-Wframe-larger-than=]
static int hexium_probe(struct saa7146_dev *dev)
^
drivers/media/pci/saa7146/hexium_gemini.c:257:12: error: stack frame size of 2304 bytes in function 'hexium_attach'
[-Werror,-Wframe-larger-than=]
static int hexium_attach(struct saa7146_dev *dev, struct saa7146_pci_extension_data *info)
^
This one happens regardless of KASAN, and the problem is that a
constructor to initialize a dynamically allocated structure leads
to a copy of that structure on the stack, whereas gcc initializes
it in place.
The driver is reporting support for NVME even when not configured for NVME
operation.
Fix (and make more readable) when NVME protocol support is indicated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The FDMI manufacturer value being reported on Linux is inconsistent with
other OS's.
Set the value to "Emulex Corporation" for consistency.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is not possible to use devm_kzalloc since that memory is
freed immediately when the device instance is unbound.
Various objects like the video device may still be in use
since someone has the device node open, and when that is closed
it expects the memory to be around.
So use kzalloc and release it at the appropriate time.
The media_device is part of a static global vimc_device struct.
The media framework expects this to be zeroed before it is
used, however, since this is a global this is not the case if
vimc is unbound and then bound again.
So call memset to ensure any left-over values are cleared.
When streaming is stopped all URBs are killed, but in fill_frame and in
bulk_irq this results in an attempt to resubmit the killed URB. That is
not what you want and causes spurious kernel messages.
So check if streaming has stopped before resubmitting.
Also check against gspca_dev->streaming rather than vb2_start_streaming_called()
since vb2_start_streaming_called() will return true when in stop_streaming,
but gspca_dev->streaming is set to false when stop_streaming is called.
Fixes: 6992effe5344 ("gspca: Kill all URBs before releasing any of them") Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The state TASK_UNINTERRUPTIBLE should be set just before
schedule_timeout() call, so it knows the sleep mode it should enter.
There is no point in setting TASK_UNINTERRUPTIBLE at the initialization
of the thread as schedule_timeout() will set the state back to
TASK_RUNNING.
This fixes a warning in __might_sleep() call, as it's expecting the
task to be in TASK_RUNNING state just before changing the state to
a sleeping state.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by: Helen Koike <helen.koike@collabora.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
The kms_plane@plane-position-covered-pipe-*-planes subtests can produce
a sequence of atomic commits such that neither active_changed nor
mode_changed but connectors_changed.
When this happens we remove the old stream from the context and add
a new stream but the new stream doesn't have mode_changed=true set.
This incorrect programming sequence causes CRC mismatches to occur in
the test.
The stream->mode_changed value should be set whenever a new stream
is created.
[How]
A new stream is created whenever drm_atomic_crtc_needs_modeset is true.
We previously covered the active_changed and mode_changed conditions
for the CRTC but connectors_changed is also checked within
drm_atomic_crtc_needs_modeset.
So just use drm_atomic_crtc_needs_modeset directly to determine the
mode_changed flag.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver should really call dm365_isif_setup_pinmux() through a callback,
but uses a hack to include a davinci specific machine header file when
compile testing instead. This works almost everywhere, but not on the
ARM omap1 platform, which has another header named mach/mux.h. This
causes a build failure:
drivers/staging/media/davinci_vpfe/dm365_isif.c:2028:2: error: implicit declaration of function 'davinci_cfg_reg' [-Werror,-Wimplicit-function-declaration]
davinci_cfg_reg(DM365_VIN_CAM_WEN);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2028:2: error: this function declaration is not a prototype [-Werror,-Wstrict-prototypes]
drivers/staging/media/davinci_vpfe/dm365_isif.c:2028:18: error: use of undeclared identifier 'DM365_VIN_CAM_WEN'
davinci_cfg_reg(DM365_VIN_CAM_WEN);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2029:18: error: use of undeclared identifier 'DM365_VIN_CAM_VD'
davinci_cfg_reg(DM365_VIN_CAM_VD);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2030:18: error: use of undeclared identifier 'DM365_VIN_CAM_HD'
davinci_cfg_reg(DM365_VIN_CAM_HD);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2031:18: error: use of undeclared identifier 'DM365_VIN_YIN4_7_EN'
davinci_cfg_reg(DM365_VIN_YIN4_7_EN);
^
drivers/staging/media/davinci_vpfe/dm365_isif.c:2032:18: error: use of undeclared identifier 'DM365_VIN_YIN0_3_EN'
davinci_cfg_reg(DM365_VIN_YIN0_3_EN);
^
7 errors generated.
Exclude omap1 from compile-testing, under the assumption that all others
still work.
Fixes: 4907c73deefe ("media: staging: davinci_vpfe: allow building with COMPILE_TEST") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
[why]
Stream update will adjust both info packets and stream params,
need to make sure all things are applied togather.
[how]
add pipe lock during stream update
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Leo Li <sunpeng.li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 14f4eaeddabc ("media: dvbsky: fix driver unregister logic") fixed
a use-after-free by removing the reference to the frontend after deleting
the backing i2c device.
This has the unfortunate side effect the frontend device is never freed
in the dvb core leaving a dangling device, leading to errors when the
dvb core tries to register the frontend after e.g. a replug as reported
here: https://www.spinics.net/lists/linux-media/msg138181.html
The use after free happened as dvb_usbv2_disconnect calls in this order:
- dvb_usb_device::props->exit(...)
- dvb_usbv2_adapter_frontend_exit(...)
+ if (fe) dvb_unregister_frontend(fe)
+ dvb_usb_device::props->frontend_detach(...)
Moving the release of the i2c device from exit() to frontend_detach()
avoids the dangling pointer access and allows the core to unregister
the frontend.
This was originally reported for a DVBSky T680CI, but it also affects
the MyGica T230C. As all supported devices structure the registration/
unregistration identically, apply the change for all device types.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
si2165_readreg8() may fail. Looking into si2165_readreg8(), we will find
that "val_tmp" will be an uninitialized value when regmap_read() fails.
"val_tmp" is then assigned to "val". So if si2165_readreg8() fails,
"val" will be a random value. Further use will lead to undefined
behaviors. The fix checks if si2165_readreg8() fails, and if so, returns
its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: Matthias Schwarzott <zzam@gentoo.org> Tested-by: Matthias Schwarzott <zzam@gentoo.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are some new e1000e devices can only be woken up from D3 one time,
by plugging Ethernet cable. Subsequent cable plugging does set PME bit
correctly, but it still doesn't get woken up.
Since e1000e connects to the root complex directly, we rely on ACPI to
wake it up. In this case, the GPE from _PRW only works once and stops
working after that. Though it appears to be a platform bug, e1000e
maintainers confirmed that I219 does not support D3.
So disable runtime PM on CNP+ chips. We may need to disable earlier
generations if this bug also hit older platforms.
Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=280819 Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The imgu_rpm_dummy_cb() looks like an API misuse that is explained
in the comment above it. Aside from that, it also causes a warning
when power management support is disabled:
drivers/staging/media/ipu3/ipu3.c:794:12: error: 'imgu_rpm_dummy_cb' defined but not used [-Werror=unused-function]
The warning is at least easy to fix by marking the function as
__maybe_unused.
[Why]
The plane_reset callback is subclassed but hasn't been updated since
the drm helper got updated to include resetting alpha related state
(state->alpha and state->pixel_blend_mode). The overlay planes
exposed by amdgpu_dm were therefore being rendered as invisible by
default ever since supported was exposed for alpha blending properties
on overlays.
This caused regressions in igt@kms_plane_multiple@atomic-tiling-none
and igt@kms_plane@plane-position-covered-pipe tests.
[How]
Reset the plane state values to their correct values as defined in
the drm helper.
This fixes the IGT test regression.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Harry Wentland <Harry.Wentland@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
In certain cases we do link training when we don't have a backend.
[How]
In dc_link_set_preferred_link_settings(), store preferred link settings
first and then verify that the link is DP and the link stream's backend is
enabled. If either is false, then we will not do any link retraining.
Signed-off-by: Samson Tam <Samson.Tam@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Releasing planes should not release the 2nd odm pipe right away,
this change leaves us with 2 pipes with null planes and same stream
when planes are released during odm.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Memory allocated via kmemdup might fail and return a NULL pointer.
This patch adds a check on the return value of kmemdup and passes the
error upstream.
In enumerate_services, ida_simple_get on failure can return an error and
leaks memory. The patch ensures that the dev_set_name is set on non
failure cases, and releases memory during failure.
The buffer descriptor setup loop is correct only if it is setting up at
least one bd struct. Besides, there is an error if dma_map_sg() returns
0, which is possible and must be handled.
Additionally, remove the BUG_ON() checking sglen, which is unnecessary
because we configure DMA with that constraint during init.
calculates the physical processor ID from the initial_apicid by shifting
*bits*.
However, this does not work for 1-Die and 2-Die 2-socket systems.
According to document [1] section 2.1.11.1, the bits is the value of
CPUID_Fn80000008_ECX[12:15]. The possible values are 4, 5 or 6 which
mean:
4 - 1 die
5 - 2 dies
6 - 3/4 dies.
Hygon programs the initial ApicId the same way as AMD. The ApicId is
read from CPUID_Fn00000001_EBX (see section 2.1.11.1 of referrence [1])
and the definition is as below (see section 2.1.10.2.1.3 of [1]):
-------------------------------------------------
Bit | 6 | 5 4 | 3 | 2 1 0 |
|-----------|---------|--------|----------------|
IDs | Socket ID | Node ID | CCX ID | Core/Thread ID |
-------------------------------------------------
So for 3/4-Die configurations, the bits variable is 6, which is the same
as the ApicID definition field.
For 1-Die and 2-Die configurations, bits is 4 or 5, which will cause the
right shifted result to not be exactly the value of socket ID.
However, the socket ID should be obtained from ApicId[6]. To fix the
problem and match the ApicID field definition, set the shift bits to 6
for all Hygon family 18h multi-die CPUs.
Because AMD doesn't have 2-Socket systems with 1-Die/2-Die processors
(see reference [2]), this doesn't need to be changed on the AMD side but
only for Hygon.
adma driver is using pm_clk_*() interface for managing clock resources.
With this it is observed that clocks remain ON always. This happens on
Tegra devices which use BPMP co-processor to manage clock resources,
where clocks are enabled during prepare phase. This is necessary because
clocks to BPMP are always blocking. When pm_clk_*() interface is used on
such Tegra devices, clock prepare count is not balanced till remove call
happens for the driver and hence clocks are seen ON always. Thus this
patch replaces pm_clk_*() with devm_clk_*() framework.
Currently incoming ARP Replies, for example via a DHT-PUT message, do
not update the timeout for an already existing DAT entry. These ARP
Replies are dropped instead.
This however defeats the purpose of the DHCPACK snooping, for instance.
Right now, a DAT entry in the DHT will be purged every five minutes,
likely leading to a mesh-wide ARP Request broadcast after this timeout.
Which then recreates the entry. The idea of the DHCPACK snooping is to
be able to update an entry before a timeout happens, to avoid ARP Request
flooding.
This patch fixes this issue by updating a DAT entry on incoming
ARP Replies even if a matching DAT entry already exists. While still
filtering the ARP Reply towards the soft-interface, to avoid duplicate
messages on the client device side.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue> Acked-by: Antonio Quartulli <a@unstable.cc> Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang correctly points out a code path that would lead
to an uninitialized variable use:
security/selinux/netlabel.c:310:6: error: variable 'addr' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (ip_hdr(skb)->version == 4) {
^~~~~~~~~~~~~~~~~~~~~~~~~
security/selinux/netlabel.c:322:40: note: uninitialized use occurs here
rc = netlbl_conn_setattr(ep->base.sk, addr, &secattr);
^~~~
security/selinux/netlabel.c:310:2: note: remove the 'if' if its condition is always true
if (ip_hdr(skb)->version == 4) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
security/selinux/netlabel.c:291:23: note: initialize the variable 'addr' to silence this warning
struct sockaddr *addr;
^
= NULL
This is probably harmless since we should not see ipv6 packets
of CONFIG_IPV6 is disabled, but it's better to rearrange the code
so this cannot happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[PM: removed old patchwork link, fixed checkpatch.pl style errors] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the current implementation of ice_reset_subtask, if multiple reset
types are set in the pf->state, the most intrusive one is meant to be
performed only, but the bits requesting the other types are not being
cleared. This would lead to another reset being performed the next time
the service task is scheduled.
Change the flow of ice_reset_subtask so that all reset request bits in
pf->state are cleared, and we still perform the most intrusive of the
resets requested.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang -Wuninitialized incorrectly sees a variable being used without
initialization:
drivers/scsi/lpfc/lpfc_nvme.c:2102:37: error: variable 'localport' is uninitialized when used here
[-Werror,-Wuninitialized]
lport = (struct lpfc_nvme_lport *)localport->private;
^~~~~~~~~
drivers/scsi/lpfc/lpfc_nvme.c:2059:38: note: initialize the variable 'localport' to silence this warning
struct nvme_fc_local_port *localport;
^
= NULL
1 error generated.
This is clearly in dead code, as the condition leading up to it is always
false when CONFIG_NVME_FC is disabled, and the variable is always
initialized when nvme_fc_register_localport() got called successfully.
Change the preprocessor conditional to the equivalent C construct, which
makes the code more readable and gets rid of the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: James Smart <james.smart@broadcom.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang -Wuninitialized notices that on is_qla40XX we never allocate any DMA
memory in get_fw_boot_info() but attempt to free it anyway:
drivers/scsi/qla4xxx/ql4_os.c:5915:7: error: variable 'buf_dma' is used uninitialized whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
if (!(val & 0x07)) {
^~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5985:47: note: uninitialized use occurs here
dma_free_coherent(&ha->pdev->dev, size, buf, buf_dma);
^~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5915:3: note: remove the 'if' if its condition is always true
if (!(val & 0x07)) {
^~~~~~~~~~~~~~~~~~~
drivers/scsi/qla4xxx/ql4_os.c:5885:20: note: initialize the variable 'buf_dma' to silence this warning
dma_addr_t buf_dma;
^
= 0
Skip the call to dma_free_coherent() here.
Fixes: 2a991c215978 ("[SCSI] qla4xxx: Boot from SAN support for open-iscsi") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If ohci-platform is runtime suspended, we can currently get an "imprecise
external abort" on reboot with ohci-platform loaded when PM runtime
is implemented for the SoC.
Let's fix this by adding PM runtime support to usb_hcd_platform_shutdown.
Signed-off-by: Tony Lindgren <tony@atomide.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The rcu_head_after_call_rcu() function reads the rhp->func pointer twice,
which can result in a false-positive WARN_ON_ONCE() if the callback
were passed to call_rcu() between the two reads. Although racing
rcu_head_after_call_rcu() with call_rcu() is to be a dubious use case
(the return value is not reliable in that case), intermittent and
irreproducible warnings are also quite dubious. This commit therefore
uses a single READ_ONCE() to pick up the value of rhp->func once, then
tests that value twice, thus guaranteeing consistent processing within
rcu_head_after_call_rcu()().
Neverthless, racing rcu_head_after_call_rcu() with call_rcu() is still
a dubious use case.
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
[ paulmck: Add blank line after declaration per checkpatch.pl. ] Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the specified rcuperf.perf_type is not in the rcu_perf_init()
function's perf_ops[] array, rcuperf prints some console messages and
then invokes rcu_perf_cleanup() to set state so that a future torture
test can run. However, rcu_perf_cleanup() also attempts to end the
test that didn't actually start, and in doing so relies on the value
of cur_ops, a value that is not particularly relevant in this case.
This can result in confusing output or even follow-on failures due to
attempts to use facilities that have not been properly initialized.
This commit therefore sets the value of cur_ops to NULL in this case and
inserts a check near the beginning of rcu_perf_cleanup(), thus avoiding
relying on an irrelevant cur_ops value.
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Linux reads MCG_CAP[Count] to find the number of MCA banks visible to a
CPU. Currently, this number is the same for all CPUs and a warning is
shown if there is a difference. The number of banks is overwritten with
the MCG_CAP[Count] value of each following CPU that boots.
According to the Intel SDM and AMD APM, the MCG_CAP[Count] value gives
the number of banks that are available to a "processor implementation".
The AMD BKDGs/PPRs further clarify that this value is per core. This
value has historically been the same for every core in the system, but
that is not an architectural requirement.
Future AMD systems may have different MCG_CAP[Count] values per core,
so the assumption that all CPUs will have the same MCG_CAP[Count] value
will no longer be valid.
Also, the first CPU to boot will allocate the struct mce_banks[] array
using the number of banks based on its MCG_CAP[Count] value. The machine
check handler and other functions use the global number of banks to
iterate and index into the mce_banks[] array. So it's possible to use an
out-of-bounds index on an asymmetric system where a following CPU sees a
MCG_CAP[Count] value greater than its predecessors.
Thus, allocate the mce_banks[] array to the maximum number of banks.
This will avoid the potential out-of-bounds index since the value of
mca_cfg.banks is capped to MAX_NR_BANKS.
Set the value of mca_cfg.banks equal to the max of the previous value
and the value for the current CPU. This way mca_cfg.banks will always
represent the max number of banks detected on any CPU in the system.
This will ensure that all CPUs will access all the banks that are
visible to them. A CPU that can access fewer than the max number of
banks will find the registers of the extra banks to be read-as-zero.
Furthermore, print the resulting number of MCA banks in use. Do this in
mcheck_late_init() so that the final value is printed after all CPUs
have been initialized.
Finally, get bank count from target CPU when doing injection with mce-inject
module.
[ bp: Remove out-of-bounds example, passify and cleanup commit message. ]
If the specified rcutorture.torture_type is not in the rcu_torture_init()
function's torture_ops[] array, rcutorture prints some console messages
and then invokes rcu_torture_cleanup() to set state so that a future
torture test can run. However, rcu_torture_cleanup() also attempts to
end the test that didn't actually start, and in doing so relies on the
value of cur_ops, a value that is not particularly relevant in this case.
This can result in confusing output or even follow-on failures due to
attempts to use facilities that have not been properly initialized.
This commit therefore sets the value of cur_ops to NULL in this case
and inserts a check near the beginning of rcu_torture_cleanup(),
thus avoiding relying on an irrelevant cur_ops value.
Reported-by: kernel test robot <rong.a.chen@intel.com> Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There has been a lurking "TBD" in the machine check poll routine ever
since it was first split out from the machine check handler. The
potential issue is that the poll routine may have just begun a read from
the STATUS register in a machine check bank when the hardware logs an
error in that bank and signals a machine check.
That race used to be pretty small back when machine checks were
broadcast, but the addition of local machine check means that the poll
code could continue running and clear the error from the bank before the
local machine check handler on another CPU gets around to reading it.
Fix the code to be sure to only process errors that need to be processed
in the poll code, leaving other logged errors alone for the machine
check handler to find and process.
[ bp: Massage a bit and flip the "== 0" check to the usual !(..) test. ]
Fixes: b79109c3bbcf ("x86, mce: separate correct machine check poller and fatal exception handler") Fixes: ed7290d0ee8f ("x86, mce: implement new status bits") Reported-by: Ashok Raj <ashok.raj@intel.com> Signed-off-by: Tony Luck <tony.luck@intel.com> Signed-off-by: Borislav Petkov <bp@suse.de> Cc: Ashok Raj <ashok.raj@intel.com> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-edac <linux-edac@vger.kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Cc: Yazen Ghannam <Yazen.Ghannam@amd.com> Link: https://lkml.kernel.org/r/20190312170938.GA23035@agluck-desk Signed-off-by: Sasha Levin <sashal@kernel.org>
The module was initializing completions whenever it was going to wait on
them, and not when the completion was allocated. This is incorrect
according to the completion docs:
Calling init_completion() on the same completion object twice is
most likely a bug [...]
Re-initialization is also unnecessary because the module never uses
complete_all(). Fix this by only ever initializing the completion a
single time, and log if the completions are not consumed as intended
(this is not a fatal problem, but should not go unnoticed).
ipw->attr_memory and ipw->common_memory are assigned with the
return value of ioremap. ioremap may fail, but no checks
are enforced. The fix inserts the checks to avoid potential
NULL pointer dereferences.
Signed-off-by: Kangjie Lu <kjlu@umn.edu> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For regular serial ports we do not initialize value of vtermno
variable. A garbage value is assigned for non console ports.
The value can be observed as a random integer with [1].
[1] vim /sys/kernel/debug/virtio-ports/vport*p*
This patch initialize the value of vtermno for console serial
ports to '1' and regular serial ports are initiaized to '0'.
Fixes the following crash as the return was missing from the check if an
fcport is offloaded. If we hit this code we continue to try to post an
invalid task which can lead to the crash:
Several people reported testing failures after setting CLOCK_REALTIME close
to the limits of the kernel internal representation in nanoseconds,
i.e. year 2262.
The failures are exposed in subsequent operations, i.e. when arming timers
or when the advancing CLOCK_MONOTONIC makes the calculation of
CLOCK_REALTIME overflow into negative space.
Now people start to paper over the underlying problem by clamping
calculations to the valid range, but that's just wrong because such
workarounds will prevent detection of real issues as well.
It is reasonable to force an upper bound for the various methods of setting
CLOCK_REALTIME. Year 2262 is the absolute upper bound. Assume a maximum
uptime of 30 years which is plenty enough even for esoteric embedded
systems. That results in an upper bound of year 2232 for setting the time.
Once that limit is reached in reality this limit is only a small part of
the problem space. But until then this stops people from trying to paper
over the problem at the wrong places.
Reported-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Reported-by: Hongbo Yao <yaohongbo@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Stephen Boyd <sboyd@kernel.org> Cc: Miroslav Lichvar <mlichvar@redhat.com> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1903231125480.2157@nanos.tec.linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
On the D3 SoC the LVDS PHY must be enabled in the same register write
that enables the LVDS output. Skip writing the LVEN bit independently
on that platform, it will be set by the write that sets LVRES.
38ac0287b7f4 ("fbdev/efifb: Honour UEFI memory map attributes when mapping the FB")
efifb_probe() checks its memory range via efi_mem_desc_lookup(),
and this leads to a spurious error message:
EFI_MEMMAP is not enabled
at every boot on KVM. This is quite annoying since the error message
appears even if you set "quiet" boot option.
Since this happens on legacy boot, which strangely enough exposes
a EFI framebuffer via screen_info, let's double check that we are
doing an EFI boot before attempting to access the EFI memory map.
Reported-by: Takashi Iwai <tiwai@suse.de> Tested-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Cc: Peter Jones <pjones@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-efi@vger.kernel.org Link: http://lkml.kernel.org/r/20190328193429.21373-3-ard.biesheuvel@linaro.org Signed-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch marks skb->data as untrusted so it warns that "evt_hdr->dlen"
can copy up to 255 bytes and we only have room for two bytes. Even
if this comes from the firmware and we trust it, the new policy
generally is just to fix it as kernel hardenning.
I can't test this code so I tried to be very conservative. I considered
not allowing "evt_hdr->dlen == 1" because it doesn't initialize the
whole variable but in the end I decided to allow it and manually
initialized "asic_id" and "asic_ver" to zero.
Fixes: e8454ff7b9a4 ("[media] drivers:media:radio: wl128x: FM Driver Common sources") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is hitting use-after-free bug in uinput module [1]. This is because
kobject_uevent(KOBJ_REMOVE) is called again due to commit 0f4dafc0563c6c49
("Kobject: auto-cleanup on final unref") after memory allocation fault
injection made kobject_uevent(KOBJ_REMOVE) from device_del() from
input_unregister_device() fail, while uinput_destroy_device() is expecting
that kobject_uevent(KOBJ_REMOVE) is not called after device_del() from
input_unregister_device() completed.
That commit intended to catch cases where nobody even attempted to send
"remove" uevents. But there is no guarantee that an event will ultimately
be sent. We are at the point of no return as far as the rest of the kernel
is concerned; there are no repeats or do-overs.
Also, it is not clear whether some subsystem depends on that commit.
If no subsystem depends on that commit, it will be better to remove
the state_{add,remove}_uevent_sent logic. But we don't want to risk
a regression (in a patch which will be backported) by trying to remove
that logic. Therefore, as a first step, let's avoid the use-after-free bug
by making sure that kobject_uevent(KOBJ_REMOVE) won't be triggered twice.
According to hidpp20_batterylevel_get_battery_info my Logitech K270
keyboard reports only 2 battery levels. This matches with what I've seen
after testing with batteries at varying level of fullness, it always
reports either 5% or 30%.
Windows reports "battery good" for the 30% level. I've captured an USB
trace of Windows reading the battery and it is getting the same info
as the Linux hidpp code gets.
Now that Linux handles these devices as hidpp devices, it reports the
battery as being low as it treats anything under 31% as low, this leads
to the user constantly getting a "Keyboard battery is low" warning from
GNOME3, which is very annoying.
This commit fixes this by changing the low threshold to anything under
30%, which I assume is what Windows does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
As a result, change the parent clocks of the Audio-DMAC{0,1} module
clocks on R-Car H3, R-Car M3-W, and R-Car M3-N to S1D2, and change the
parent clock of the Audio-DMAC0 module on R-Car E3 to S1D2.
NOTE: This information will be reflected in a future revision of the
R-Car Gen3 Hardware Manual.
xen_biovec_phys_mergeable() only needs .bv_page of the 2nd bio bvec
for checking if the two bvecs can be merged, so pass page to
xen_biovec_phys_mergeable() directly.
No function change.
Cc: ris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: xen-devel@lists.xenproject.org Cc: Omar Sandoval <osandov@fb.com> Cc: Christoph Hellwig <hch@lst.de> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The use of zero-sized array causes undefined behaviour when it is not
the last member in a structure. As it happens to be in this case.
Also, the current code makes use of a language extension to the C90
standard, but the preferred mechanism to declare variable-length
types such as this one is a flexible array member, introduced in
C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last. Which is beneficial
to cultivate a high-quality code.
Fixes: e48f129c2f20 ("[SCSI] cxgb3i: convert cdev->l2opt to use rcu to prevent NULL dereference") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/fsl_utils.c:74:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 38, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Timur Tabi <timur@kernel.org> Cc: Nicolin Chen <nicoleotsuka@gmail.com> Cc: Xiubo Li <Xiubo.Lee@gmail.com> Cc: Fabio Estevam <festevam@gmail.com> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./sound/soc/fsl/eukrea-tlv320.c:121:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function.
./sound/soc/fsl/eukrea-tlv320.c:127:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 102, but without a correspo nding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Jaroslav Kysela <perex@perex.cz> Cc: Takashi Iwai <tiwai@suse.com> Cc: alsa-devel@alsa-project.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log