The prepare_fb call always happens on new_plane_state.
The drm_atomic_helper_cleanup_planes checks to see if
plane state pointer has changed when deciding to call cleanup_fb on
either the new_plane_state or the old_plane_state.
For a non-async atomic commit the state pointer is swapped, so this
helper calls prepare_fb on the new_plane_state and cleanup_fb on the
old_plane_state. This makes sense, since we want to prepare the
framebuffer we are going to use and cleanup the the framebuffer we are
no longer using.
For the async atomic update helpers this differs. The async atomic
update helpers perform in-place updates on the existing state. They call
drm_atomic_helper_cleanup_planes but the state pointer is not swapped.
This means that prepare_fb is called on the new_plane_state and
cleanup_fb is called on the new_plane_state (not the old).
In the case where old_plane_state->fb == new_plane_state->fb then
there should be no behavioral difference between an async update
and a non-async commit. But there are issues that arise when
old_plane_state->fb != new_plane_state->fb.
The first is that the new_plane_state->fb is immediately cleaned up
after it has been prepared, so we're using a fb that we shouldn't
be.
The second occurs during a sequence of async atomic updates and
non-async regular atomic commits. Suppose there are two framebuffers
being interleaved in a double-buffering scenario, fb1 and fb2:
In reshape_request it already adds len to sector_nr already. It's wrong to add len to
sector_nr again after adding pages to bio. If there is bad block it can't copy one chunk
at a time, it needs to goto read_more. Now the sector_nr is wrong. It can cause data
corruption.
Cc: stable@vger.kernel.org # v3.16+ Signed-off-by: Xiao Ni <xni@redhat.com> Signed-off-by: Song Liu <songliubraving@fb.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Acer TravelMate X514-51T with ALC255 cannot detect the headset MIC
until ALC255_FIXUP_ACER_HEADSET_MIC quirk applied. Although, the
internal DMIC uses another module - snd_soc_skl as the driver. We still
need the NID 0x1a in the quirk to enable the headset MIC.
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Kailang Yang <kailang@realtek.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dell Precision 5820 with ALC3234 codec (which is equivalent with
ALC255) shows click noises at (runtime) PM resume on the headphone.
The biggest source of the noise comes from the cleared headphone pin
control at resume, which is done via the standard shutup procedure.
Although we have an override of the standard shutup callback to
replace with NOP, this would skip other needed stuff (e.g. the pull
down of headset power). So, instead, this "fixes" the behavior of
alc_fixup_no_shutup() by introducing spec->no_shutup_pins flag.
When this flag is set, Realtek codec won't call the standard
snd_hda_shutup_pins() & co. Now alc_fixup_no_shutup() just sets this
flag instead of overriding spec->shutup callback itself. This allows
us to apply the similar fix for other entries easily if needed in
future.
The ASUS UX362FA with ALC294 cannot detect the headset MIC and outputs
through the internal speaker and the headphone. This issue can be fixed
by the quirk in the commit 4e0511067 ALSA: hda/realtek: Enable audio
jacks of ASUS UX533FD with ALC294.
Besides, ASUS UX362FA and UX533FD have the same audio initial pin config
values. So, this patch replaces SND_PCI_QUIRK of UX533FD with a new
SND_HDA_PIN_QUIRK which benefits both UX362FA and UX533FD.
Fixes: 4e051106730d ("ALSA: hda/realtek: Enable audio jacks of ASUS UX533FD with ALC294") Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com> Signed-off-by: Ming Shuo Chiu <chiu@endlessm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I set 10 seconds for the timeout of the i915 audio component binding
with a hope that recent machines are fast enough to handle all probe
tasks in that period, but I was too optimistic. The binding may take
longer than that, and this caused a problem on the machine with both
audio and graphics driver modules loaded in parallel, as Paul Menzel
experienced. This problem haven't hit so often just because the KMS
driver is loaded in initrd on most machines.
As a simple workaround, extend the timeout to 60 seconds.
In data blocks of common isochronous packet for MOTU devices, PCM
frames are multiplexed in a shape of '24 bit * 4 Audio Pack', described
in IEC 61883-6. The frames are not aligned to quadlet.
For capture PCM substream, ALSA firewire-motu driver constructs PCM
frames by reading data blocks byte-by-byte. However this operation
includes bug for lower byte of the PCM sample. This brings invalid
content of the PCM samples.
ALSA bebob driver has an entry for Focusrite Saffire Pro 10 I/O. The
entry matches vendor_id in root directory and model_id in unit
directory of configuration ROM for IEEE 1394 bus.
On the other hand, configuration ROM of Focusrite Liquid Saffire 56
has the same vendor_id and model_id. This device is an application of
TCAT Dice (TCD2220 a.k.a Dice Jr.) however ALSA bebob driver can be
bound to it randomly instead of ALSA dice driver. At present, drivers
in ALSA firewire stack can not handle this situation appropriately.
This commit uses more identical mod_alias for Focusrite Saffire Pro 10
I/O in ALSA bebob driver.
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 042a829d bus_info_length 4, crc_length 42, crc 33437
404 31333934 bus_name "1394"
408 f0649222 irmc 1, cmc 1, isc 1, bmc 1, pmc 0, cyc_clk_acc 100,
max_rec 9 (1024), max_rom 2, gen 2, spd 2 (S400)
40c 00130e01 company_id 00130e |
410 000606e0 device_id 01000606e0 | EUI-64 00130e01000606e0
root directory
-----------------------------------------------------------------
414 0009d31c directory_length 9, crc 54044
418 04000014 hardware version
41c 0c0083c0 node capabilities per IEEE 1394
420 0300130e vendor
424 81000012 --> descriptor leaf at 46c
428 17000006 model
42c 81000016 --> descriptor leaf at 484
430 130120c2 version
434 d1000002 --> unit directory at 43c
438 d4000006 --> dependent info directory at 450
unit directory at 43c
-----------------------------------------------------------------
43c 0004707c directory_length 4, crc 28796
440 1200a02d specifier id: 1394 TA
444 13010001 version: AV/C
448 17000006 model
44c 81000013 --> descriptor leaf at 498
dependent info directory at 450
-----------------------------------------------------------------
450 000637c7 directory_length 6, crc 14279
454 120007f5 specifier id
458 13000001 version
45c 3affffc7 (immediate value)
460 3b100000 (immediate value)
464 3cffffc7 (immediate value)
468 3d600000 (immediate value)
$ python2 crpp < /sys/bus/firewire/devices/fw1/config_rom
ROM header and bus information block
-----------------------------------------------------------------
400 040442e4 bus_info_length 4, crc_length 4, crc 17124
404 31333934 bus_name "1394"
408 e0ff8112 irmc 1, cmc 1, isc 1, bmc 0, pmc 0, cyc_clk_acc 255,
max_rec 8 (512), max_rom 1, gen 1, spd 2 (S400)
40c 00130e04 company_id 00130e |
410 018001e9 device_id 04018001e9 | EUI-64 00130e04018001e9
root directory
-----------------------------------------------------------------
414 00065612 directory_length 6, crc 22034
418 0300130e vendor
41c 8100000a --> descriptor leaf at 444
420 17000006 model
424 8100000e --> descriptor leaf at 45c
428 0c0087c0 node capabilities per IEEE 1394
42c d1000001 --> unit directory at 430
unit directory at 430
-----------------------------------------------------------------
430 000418a0 directory_length 4, crc 6304
434 1200130e specifier id
438 13000001 version
43c 17000006 model
440 8100000f --> descriptor leaf at 47c
Guenter reported a build warning for CONFIG_CPU_SUP_INTEL=n:
> With allmodconfig-CONFIG_CPU_SUP_INTEL, this patch results in:
>
> In file included from arch/x86/events/amd/core.c:8:0:
> arch/x86/events/amd/../perf_event.h:1036:45: warning: ‘struct cpu_hw_event’ declared inside parameter list will not be visible outside of this definition or declaration
> static inline int intel_cpuc_prepare(struct cpu_hw_event *cpuc, int cpu)
While harmless (an unsed pointer is an unused pointer, no matter the type)
it needs fixing.
Thread A Thread B
- f2fs_write_data_pages
- __write_data_page
- f2fs_submit_page_write
- inc_page_count(F2FS_WB_DATA)
type is F2FS_WB_DATA due to file is non-atomic one
- f2fs_ioc_start_atomic_write
- set_inode_flag(FI_ATOMIC_FILE)
- f2fs_write_end_io
- dec_page_count(F2FS_WB_CP_DATA)
type is F2FS_WB_DATA due to file becomes
atomic one
When adding new filter to flower classifier, fl_change() inserts it to
handle_idr before initializing filter extensions and assigning it a mask.
Normally this ordering doesn't matter because all flower classifier ops
callbacks assume rtnl lock protection. However, when filter has an action
that doesn't have its kernel module loaded, rtnl lock is released before
call to request_module(). During this time the filter can be accessed bu
concurrent task before its initialization is completed, which can lead to a
crash.
Example case of NULL pointer dereference in concurrent dump:
Extension initialization and mask assignment don't depend on fnew->handle
that is allocated by idr_alloc_u32(). Move idr allocation code after action
creation and mask assignment in fl_change() to prevent concurrent access
to not fully initialized filter when rtnl lock is released to load action
module.
Fixes: 01683a146999 ("net: sched: refactor flower walk to iterate over idr") Signed-off-by: Vlad Buslov <vladbu@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous to commit 22b5c0b63f32 ("vsock/virtio: fix kernel panic
after device hot-unplug"), vsock_core_init() was called from
virtio_vsock_probe(). Now, virtio_transport_reset_no_sock() can be called
before vsock_core_init() has the chance to run.
[Wed Feb 27 14:17:09 2019] BUG: unable to handle kernel NULL pointer dereference at 0000000000000110
[Wed Feb 27 14:17:09 2019] #PF error: [normal kernel read fault]
[Wed Feb 27 14:17:09 2019] PGD 0 P4D 0
[Wed Feb 27 14:17:09 2019] Oops: 0000 [#1] SMP PTI
[Wed Feb 27 14:17:09 2019] CPU: 3 PID: 59 Comm: kworker/3:1 Not tainted 5.0.0-rc7-390-generic-hvi #390
[Wed Feb 27 14:17:09 2019] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[Wed Feb 27 14:17:09 2019] Workqueue: virtio_vsock virtio_transport_rx_work [vmw_vsock_virtio_transport]
[Wed Feb 27 14:17:09 2019] RIP: 0010:virtio_transport_reset_no_sock+0x8c/0xc0 [vmw_vsock_virtio_transport_common]
[Wed Feb 27 14:17:09 2019] Code: 35 8b 4f 14 48 8b 57 08 31 f6 44 8b 4f 10 44 8b 07 48 8d 7d c8 e8 84 f8 ff ff 48 85 c0 48 89 c3 74 2a e8 f7 31 03 00 48 89 df <48> 8b 80 10 01 00 00 e8 68 fb 69 ed 48 8b 75 f0 65 48 33 34 25 28
[Wed Feb 27 14:17:09 2019] RSP: 0018:ffffb42701ab7d40 EFLAGS: 00010282
[Wed Feb 27 14:17:09 2019] RAX: 0000000000000000 RBX: ffff9d79637ee080 RCX: 0000000000000003
[Wed Feb 27 14:17:09 2019] RDX: 0000000000000001 RSI: 0000000000000002 RDI: ffff9d79637ee080
[Wed Feb 27 14:17:09 2019] RBP: ffffb42701ab7d78 R08: ffff9d796fae70e0 R09: ffff9d796f403500
[Wed Feb 27 14:17:09 2019] R10: ffffb42701ab7d90 R11: 0000000000000000 R12: ffff9d7969d09240
[Wed Feb 27 14:17:09 2019] R13: ffff9d79624e6840 R14: ffff9d7969d09318 R15: ffff9d796d48ff80
[Wed Feb 27 14:17:09 2019] FS: 0000000000000000(0000) GS:ffff9d796fac0000(0000) knlGS:0000000000000000
[Wed Feb 27 14:17:09 2019] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[Wed Feb 27 14:17:09 2019] CR2: 0000000000000110 CR3: 0000000427f22000 CR4: 00000000000006e0
[Wed Feb 27 14:17:09 2019] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[Wed Feb 27 14:17:09 2019] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[Wed Feb 27 14:17:09 2019] Call Trace:
[Wed Feb 27 14:17:09 2019] virtio_transport_recv_pkt+0x63/0x820 [vmw_vsock_virtio_transport_common]
[Wed Feb 27 14:17:09 2019] ? kfree+0x17e/0x190
[Wed Feb 27 14:17:09 2019] ? detach_buf_split+0x145/0x160
[Wed Feb 27 14:17:09 2019] ? __switch_to_asm+0x40/0x70
[Wed Feb 27 14:17:09 2019] virtio_transport_rx_work+0xa0/0x106 [vmw_vsock_virtio_transport]
[Wed Feb 27 14:17:09 2019] NET: Registered protocol family 40
[Wed Feb 27 14:17:09 2019] process_one_work+0x167/0x410
[Wed Feb 27 14:17:09 2019] worker_thread+0x4d/0x460
[Wed Feb 27 14:17:09 2019] kthread+0x105/0x140
[Wed Feb 27 14:17:09 2019] ? rescuer_thread+0x360/0x360
[Wed Feb 27 14:17:09 2019] ? kthread_destroy_worker+0x50/0x50
[Wed Feb 27 14:17:09 2019] ret_from_fork+0x35/0x40
[Wed Feb 27 14:17:09 2019] Modules linked in: vmw_vsock_virtio_transport vmw_vsock_virtio_transport_common input_leds vsock serio_raw i2c_piix4 mac_hid qemu_fw_cfg autofs4 cirrus ttm drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops virtio_net psmouse drm net_failover pata_acpi virtio_blk failover floppy
Fixes: 22b5c0b63f32 ("vsock/virtio: fix kernel panic after device hot-unplug") Reported-by: Alexandru Herghelegiu <aherghelegiu@bitdefender.com> Signed-off-by: Adalbert Lazăr <alazar@bitdefender.com> Co-developed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit bfcb79fca19d
("PCI/ERR: Run error recovery callbacks for all affected devices")
affected the non-fatal error recovery logic for the HNS and RDMA devices.
This is because each HNS PF under PCIe bus receive callbacks
from the AER driver when an error is reported for one of the PF.
This causes unwanted PF resets because
the HNS decides which PF to reset based on the reset type set.
The HNS error handling code sets the reset type based on the hw error
type detected.
This patch provides fix for the above issue for the recovery of
the hw errors in the HNS and RDMA devices.
This patch needs backporting to the kernel v5.0+
Fixes: 332fbf576579 ("net: hns3: add handling of hw ras errors using new set of commands") Reported-by: Xiaofei Tan <tanxiaofei@huawei.com> Signed-off-by: Shiju Jose <shiju.jose@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By default, the switch driver is expected to configure CPU and DSA
ports to their maximum speed. For the 6341 and 6390 families, the
ports interface mode has to be configured as well. The 6390X range
support 10G ports using XAUI, while the 6341 and 6390 supports
2500BaseX, as their maximum speed.
Fixes: 787799a9d555 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calculation of qp mtt size (in function mlx4_RST2INIT_wrapper)
ultimately depends on function roundup_pow_of_two.
If the amount of memory required by the QP is less than one page,
roundup_pow_of_two is called with argument zero. In this case, the
roundup_pow_of_two result is undefined.
Calling roundup_pow_of_two with a zero argument resulted in the
following stack trace:
UBSAN: Undefined behaviour in ./include/linux/log2.h:61:13
shift exponent 64 is too large for 64-bit type 'long unsigned int'
CPU: 4 PID: 26939 Comm: rping Tainted: G OE 4.19.0-rc1
Hardware name: Supermicro X9DR3-F/X9DR3-F, BIOS 3.2a 07/09/2015
Call Trace:
dump_stack+0x9a/0xeb
ubsan_epilogue+0x9/0x7c
__ubsan_handle_shift_out_of_bounds+0x254/0x29d
? __ubsan_handle_load_invalid_value+0x180/0x180
? debug_show_all_locks+0x310/0x310
? sched_clock+0x5/0x10
? sched_clock+0x5/0x10
? sched_clock_cpu+0x18/0x260
? find_held_lock+0x35/0x1e0
? mlx4_RST2INIT_QP_wrapper+0xfb1/0x1440 [mlx4_core]
mlx4_RST2INIT_QP_wrapper+0xfb1/0x1440 [mlx4_core]
Fix this by explicitly testing for zero, and returning one if the
argument is zero (assuming that the next higher power of 2 in this case
should be one).
Fixes: c82e9aa0a8bc ("mlx4_core: resource tracking for HCA resources used by guests") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In procedures mlx4_cmd_use_events() and mlx4_cmd_use_polling(), we need to
guarantee that there are no FW commands in progress on the comm channel
(for VFs) or wrapped FW commands (on the PF) when SRIOV is active.
We do this by also taking the slave_cmd_mutex when SRIOV is active.
This is especially important when switching from event to polling, since we
free the command-context array during the switch. If there are FW commands
in progress (e.g., waiting for a completion event), the completion event
handler will access freed memory.
Since the decision to use comm_wait or comm_poll is taken before grabbing
the event_sem/poll_sem in mlx4_comm_cmd_wait/poll, we must take the
slave_cmd_mutex as well (to guarantee that the decision to use events or
polling and the call to the appropriate cmd function are atomic).
Fixes: a7e1f04905e5 ("net/mlx4_core: Fix deadlock when switching between polling and event fw commands") Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As part of unloading a device, the driver switches from
FW command event mode to FW command polling mode.
Part of switching over to polling mode is freeing the command context array
memory (unfortunately, currently, without NULLing the command context array
pointer).
The reset flow calls "complete" to complete all outstanding fw commands
(if we are in event mode). The check for event vs. polling mode here
is to test if the command context array pointer is NULL.
If the reset flow is activated after the switch to polling mode, it will
attempt (incorrectly) to complete all the commands in the context array --
because the pointer was not NULLed when the driver switched over to polling
mode.
As a result, we have a use-after-free situation, which results in a
kernel crash.
Same reasons than the ones explained in commit 4179cb5a4c92
("vxlan: test dev->flags & IFF_UP before calling netif_rx()")
netif_rx() or gro_cells_receive() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
A similar protocol is used for gro_cells infrastructure, as
gro_cells_destroy() will be called only after a full rcu
grace period is observed after IFF_UP has been cleared.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Otherwise we risk use-after-free and/or crashes.
Fixes: d342894c5d2f ("vxlan: virtual extensible lan") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we receive a packet while deleting a VXLAN device, there's a chance
vxlan_rcv() is called at the same time as vxlan_dellink(). This is fine,
except that vxlan_dellink() should never ever touch stuff that's still in
use, such as the GRO cells list.
Otherwise, vxlan_rcv() crashes while queueing packets via
gro_cells_receive().
Move the gro_cells_destroy() to vxlan_uninit(), which runs after the RCU
grace period is elapsed and nothing needs the gro_cells anymore.
This is now done in the same way as commit 8e816df87997 ("geneve: Use GRO
cells infrastructure.") originally implemented for GENEVE.
Reported-by: Jianlin Shi <jishi@redhat.com> Fixes: 58ce31cca1ff ("vxlan: GRO support at tunnel layer") Signed-off-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7716682cc58e ("tcp/dccp: fix another race at listener
dismantle") let inet_csk_reqsk_queue_add() fail, and adjusted
{tcp,dccp}_check_req() accordingly. However, TFO and syncookies
weren't modified, thus leaking allocated resources on error.
Contrary to tcp_check_req(), in both syncookies and TFO cases,
we need to drop the request socket. Also, since the child socket is
created with inet_csk_clone_lock(), we have to unlock it and drop an
extra reference (->sk_refcount is initially set to 2 and
inet_csk_reqsk_queue_add() drops only one ref).
For TFO, we also need to revert the work done by tcp_try_fastopen()
(with reqsk_fastopen_remove()).
Fixes: 7716682cc58e ("tcp/dccp: fix another race at listener dismantle") Signed-off-by: Guillaume Nault <gnault@redhat.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit eeea10b83a13 ("tcp: add
tcp_v4_fill_cb()/tcp_v4_restore_cb()"), tcp_vX_fill_cb is only called
after tcp_filter(). That means, TCP_SKB_CB(skb)->end_seq still points to
the IP-part of the cb.
We thus should not mock with it, as this can trigger bugs (thanks
syzkaller):
[ 12.349396] ==================================================================
[ 12.350188] BUG: KASAN: slab-out-of-bounds in ip6_datagram_recv_specific_ctl+0x19b3/0x1a20
[ 12.351035] Read of size 1 at addr ffff88006adbc208 by task test_ip6_datagr/1799
Setting end_seq is actually no more necessary in tcp_filter as it gets
initialized later on in tcp_vX_fill_cb.
Cc: Eric Dumazet <edumazet@google.com> Fixes: eeea10b83a13 ("tcp: add tcp_v4_fill_cb()/tcp_v4_restore_cb()") Signed-off-by: Christoph Paasch <cpaasch@apple.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Returning 0 as inq to userspace indicates there is no more data to
read, and the application needs to wait for EPOLLIN. For a connection
that has received FIN from the remote peer, however, the application
must continue reading until getting EOF (return value of 0
from tcp_recvmsg) or an error, if edge-triggered epoll (EPOLLET) is
being used. Otherwise, the application will never receive a new
EPOLLIN, since there is no epoll edge after the FIN.
Return 1 when there is no data left on the queue but the
connection has received FIN, so that the applications continue
reading.
Fixes: b75eba76d3d72 (tcp: send in-queue bytes in cmsg upon read) Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com> Acked-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported a NULL-ptr deref caused by that sched->init() in
sctp_stream_init() set stream->rr_next = NULL.
kasan: GPF could be caused by NULL-ptr deref or user memory access
RIP: 0010:sctp_sched_rr_dequeue+0xd3/0x170 net/sctp/stream_sched_rr.c:141
Call Trace:
sctp_outq_dequeue_data net/sctp/outqueue.c:90 [inline]
sctp_outq_flush_data net/sctp/outqueue.c:1079 [inline]
sctp_outq_flush+0xba2/0x2790 net/sctp/outqueue.c:1205
All sched info is saved in sout->ext now, in sctp_stream_init()
sctp_stream_alloc_out() will not change it, there's no need to
call sched->init() again, since sctp_outq_init() has already
done it.
Fixes: 5bbbbe32a431 ("sctp: introduce stream scheduler foundations") Reported-by: syzbot+4c9934f20522c0efd657@syzkaller.appspotmail.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rxrpc_get_client_conn() adds a new call to the front of the waiting_calls
queue if the connection it's going to use already exists. This is bad as
it allows calls to get starved out.
Fix this by adding to the tail instead.
Also change the other enqueue point in the same function to put it on the
front (ie. when we have a new connection). This makes the point that in
the case of a new connection the new call goes at the front (though it
doesn't actually matter since the queue should be unoccupied).
Fixes: 45025bceef17 ("rxrpc: Improve management and caching of client connection objects") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The race occurs in __mkroute_output() when 2 threads lookup a dst:
CPU A CPU B
find_exception()
find_exception() [fnhe expires]
ip_del_fnhe() [fnhe is deleted]
rt_bind_exception()
In rt_bind_exception() it will bind a deleted fnhe with the new dst, and
this dst will get no chance to be freed. It causes a dev defcnt leak and
consecutive dmesg warnings:
unregister_netdevice: waiting for ethX to become free. Usage count = 1
Especially thanks Jon to identify the issue.
This patch fixes it by setting fnhe_daddr to 0 in ip_del_fnhe() to stop
binding the deleted fnhe with a new dst when checking fnhe's fnhe_daddr
and daddr in rt_bind_exception().
It works as both ip_del_fnhe() and rt_bind_exception() are protected by
fnhe_lock and the fhne is freed by kfree_rcu().
Fixes: deed49df7390 ("route: check and remove route cache when we get route") Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware has the CBS (Credit Based Shaper) which affects only Q3
and Q2. When updating the CBS settings, even if the driver does so
after waiting for Tx DMA finished, there is a possibility that frame
data still remains in TxFIFO.
To avoid this, decrease TxFIFO depth of Q3 and Q2 to one.
This patch has been exercised this using netperf TCP_MAERTS, TCP_STREAM
and UDP_STREAM tests run on an Ebisu board. No performance change was
detected, outside of noise in the tests, both in terms of throughput and
CPU utilisation.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Masaru Nagai <masaru.nagai.vx@renesas.com> Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: updated changelog] Signed-off-by: Simon Horman <horms+renesas@verge.net.au> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sk_setup_caps() is called to set sk->sk_dst_cache in pptp_connect,
so we have to dst_release(sk->sk_dst_cache) in pptp_sock_destruct,
otherwise, the dst refcnt will leak.
unregister_netdevice: waiting for lo to become free. Usage count = 1
v1->v2:
- use rcu_dereference_protected() instead of rcu_dereference_check(),
as suggested by Eric.
Fixes: 00959ade36ac ("PPTP: PPP over IPv4 (Point-to-Point Tunneling Protocol)") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 95d6ebd53c79 ("net/x25: fix use-after-free in x25_device_event()") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: andrew hendry <andrew.hendry@gmail.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of failure x25_connect() does a x25_neigh_put(x25->neighbour)
but forgets to clear x25->neighbour pointer, thus triggering use-after-free.
Since the socket is visible in x25_list, we need to hold x25_list_lock
to protect the operation.
syzbot report :
BUG: KASAN: use-after-free in x25_kill_by_device net/x25/af_x25.c:217 [inline]
BUG: KASAN: use-after-free in x25_device_event+0x296/0x2b0 net/x25/af_x25.c:252
Read of size 8 at addr ffff8880a030edd0 by task syz-executor003/7854
Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot+04babcefcd396fabec37@syzkaller.appspotmail.com Cc: andrew hendry <andrew.hendry@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: linmiaohe <linmiaohe@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Arvid Brodin <arvid.brodin@alten.se> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If hsr_add_port(hsr, hsr_dev, HSR_PT_MASTER) failed to
add port, it directly returns res and forgets to free the node
that allocated in hsr_create_self_node(), and forgets to delete
the node->mac_list linked in hsr->self_node_db.
Fixes: c5a759117210 ("net/hsr: Use list_head (and rcu) instead of array for slave devices.") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Mao Wenan <maowenan@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
HW can not guarantee complete write desc->rx.size, even though
HNS3_RXD_VLD_B has been set. Driver needs to add dma_rmb()
instruction to make sure desc->rx.size is always valid.
Fixes: e55970950556 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed that tx queue may stall while downloading
from certain web sites (example www.speedtest.net)
The cause has been tracked down to a corner case where
the tx interrupt vector was disabled automatically, but
was not re enabled later.
The lan743x has two mechanisms to enable/disable individual
interrupts. Interrupts can be enabled/disabled by individual
source, and they can also be enabled/disabled by individual
vector which has been mapped to the source. Both must be
enabled for interrupts to work properly.
The TX code path, primarily uses the interrupt enable/disable of
the TX source bit, while leaving the vector enabled all the time.
However, while investigating this issue it was noticed that
the driver requested the use of the vector auto clear feature.
The test above revealed a case where the vector enable was
cleared unintentionally.
This patch fixes the issue by deleting the lines that request
the vector auto clear feature to be used.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been noticed that running the speed test at
www.speedtest.net occasionally causes a kernel panic.
Investigation revealed that under this test RX buffer allocation
sometimes fails and returns NULL. But the lan743x driver did
not handle this case.
This patch fixes this issue by attempting to allocate a buffer
before sending the new rx packet to the OS. If the allocation
fails then the new rx packet is dropped and the existing buffer
is reused in the DMA ring.
Updates for v2:
Additional 2 locations where allocation was not checked,
has been changed to reuse existing buffer.
Fixes: 23f0703c125b ("lan743x: Add main source files for new lan743x driver") Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Local variable description: ----addr@___sys_recvmsg
Variable was created at:
___sys_recvmsg+0xf6/0x1310 net/socket.c:2244
do_recvmmsg+0x646/0x10c0 net/socket.c:2390
Bytes 0-31 of 32 are uninitialized
Memory access of size 32 starts at ffff8880ae62fbb0
Data copied to user address 0000000020000000
Fixes: a32e0eec7042 ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a non local multicast packet reaches ip_route_input_rcu() while
the ingress device IPv4 private data (in_dev) is NULL, we end up
doing a NULL pointer dereference in IN_DEV_MFORWARD().
Since the later call to ip_route_input_mc() is going to fail if
!in_dev, we can fail early in such scenario and avoid the dangerous
code path.
v1 -> v2:
- clarified the commit message, no code changes
Reported-by: Tianhao Zhao <tizhao@redhat.com> Fixes: e58e41596811 ("net: Enable support for VRF with ipv4 multicast") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
proc_exit_connector() uses ->real_parent lockless. This is not
safe that its parent can go away at any moment, so use RCU to
protect it, and ensure that this task is not released.
Fixes: b086ff87251b4a4 ("connector: add parent pid and tgid to coredump and exit events") Signed-off-by: Zhang Yu <zhangyu31@baidu.com> Signed-off-by: Li RongQing <lirongqing@baidu.com> Acked-by: Evgeniy Polyakov <zbr@ioremap.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
perf/x86/intel: Implement support for TSX Force Abort
Skylake (and later) will receive a microcode update to address a TSX
errata. This microcode will, on execution of a TSX instruction
(speculative or not) use (clobber) PMC3. This update will also provide
a new MSR to change this behaviour along with a CPUID bit to enumerate
the presence of this new MSR.
When the MSR gets set; the microcode will no longer use PMC3 but will
Force Abort every TSX transaction (upon executing COMMIT).
When TSX Force Abort (TFA) is allowed (default); the MSR gets set when
PMC3 gets scheduled and cleared when, after scheduling, PMC3 is
unused.
When TFA is not allowed; clear PMC3 from all constraints such that it
will not get used.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Skylake systems will receive a microcode update to address a TSX
errata. This microcode will (by default) clobber PMC3 when TSX
instructions are (speculatively or not) executed.
It also provides an MSR to cause all TSX transaction to abort and
preserve PMC3.
Add the CPUID enumeration and MSR definition.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ath9k_of_init() function[0] was initially written on the assumption that
if someone had an explicit ath9k OF node that "there must be something
wrong, why would someone add an OF node if everything is fine"[1]
(Quoting Martin Blumenstingl <martin.blumenstingl@googlemail.com>)
"it turns out it's not that simple. with your requirements I'm now aware
of two use-cases where the current code in ath9k_of_init() doesn't work
without modifications"[1]
The "your requirements" Martin speaks of is the result of the fact that I
have a device (PowerCloud Systems CR5000) has some kind of default - not
unique mac address - set and requires to set the correct MAC address via
mac-address devicetree property, however:
"some cards come with a physical EEPROM chip [or OTP] so "qca,no-eeprom"
should not be set (your use-case). in this case AH_USE_EEPROM should be
set (which is the default when there is no OF node)"[1]
The other use case is:
the firmware on some PowerMac G5 seems to add a OF node for the ath9k
card automatically. depending on the EEPROM on the card AH_NO_EEP_SWAP
should be unset (which is the default when there is no OF node). see [3]
After this patch to ath9k_of_init() the new behavior will be:
if there's no OF node then everything is the same as before
if there's an empty OF node then ath9k will use the hardware EEPROM
(before ath9k would fail to initialize because no EEPROM data was
provided by userspace)
if there's an OF node with only a MAC address then ath9k will use
the MAC address and the hardware EEPROM (see the case above)
with "qca,no-eeprom" EEPROM data from userspace will be requested.
the behavior here will not change
[1]
Martin provides additional background on EEPROM swapping[1].
Thanks to Christian Lamparter <chunkeey@gmail.com> for all his help on
troubleshooting this issue and the basis for this patch.
Fixes: 138b41253d9c ("ath9k: parse the device configuration from an OF node") Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Daniel F. Dickinson <cshored@thecshore.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Cc: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1751e8a6cb93 ("Rename superblock flags (MS_xyz ->
SB_xyz)"), scripts/gdb should be updated to replace MS_xyz with SB_xyz.
This change didn't directly affect the running operation of scripts/gdb
until commit e262e32d6bde "vfs: Suppress MS_* flag defs within the
kernel unless explicitly enabled" removed the definitions used by
constants.py.
Update constants.py.in to utilise the new internal flags, matching the
implementation at fs/proc_namespace.c::show_sb_opts.
Note to stable, e262e32d6bde landed in v5.0-rc1 (which was just
released), so we'll want this picked back to 5.0 stable once this patch
hits mainline (akpm just picked it up). Without this, debugging a
kernel a kernel via GDB+QEMU is broken in the 5.0 release.
[kieran.bingham@ideasonboard.com: add fixes tag, reword commit message] Link: http://lkml.kernel.org/r/20190305103014.25847-1-kieran.bingham@ideasonboard.com Fixes: e262e32d6bde "vfs: Suppress MS_* flag defs within the kernel unless explicitly enabled" Signed-off-by: Jackie Liu <liuyun01@kylinos.cn> Signed-off-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Tested-by: Nick Desaulniers <ndesaulniers@google.com> Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Cc: Dan Robertson <danlrobertson89@gmail.com> Cc: Jan Kiszka <jan.kiszka@siemens.com> Cc: David Howells <dhowells@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch resolves the following page use-after-free issue,
z_erofs_vle_unzip:
...
for (i = 0; i < nr_pages; ++i) {
...
z_erofs_onlinepage_endio(page); (1)
}
for (i = 0; i < clusterpages; ++i) {
page = compressed_pages[i];
if (page->mapping == mngda) (2)
continue;
/* recycle all individual staging pages */
(void)z_erofs_gather_if_stagingpage(page_pool, page); (3)
WRITE_ONCE(compressed_pages[i], NULL);
}
...
After (1) is executed, page is freed and could be then reused, if
compressed_pages is scanned after that, it could fall info (2) or
(3) by mistake and that could finally be in a mess.
This patch aims to solve the above issue only with little changes
as much as possible in order to make the fix backport easier.
As Al pointed out, "
... and while we are at it, what happens to
unsigned int nameoff = le16_to_cpu(de[mid].nameoff);
unsigned int matched = min(startprfx, endprfx);
/* string comparison without already matched prefix */
int ret = dirnamecmp(name, &dname, &matched);
if le16_to_cpu(de[...].nameoff) is not monotonically increasing? I.e.
what's to prevent e.g. (unsigned)-1 ending up in dname.len?
Corrupted fs image shouldn't oops the kernel.. "
Revisit the related lookup flow to address the issue.
Mark Syms has reported seeing tasks that are stuck waiting in
find_insert_glock. It turns out that struct lm_lockname contains four padding
bytes on 64-bit architectures that function glock_waitqueue doesn't skip when
hashing the glock name. As a result, we can end up waking up the wrong
waitqueue, and the waiting tasks may be stuck forever.
Fix that by using ht_parms.key_len instead of sizeof(struct lm_lockname) for
the key length.
Reported-by: Mark Syms <mark.syms@citrix.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We might have never enabled (started) the psock's parser, in which case it
will not get stopped when destroying the psock. This leads to a warning
when trying to cancel parser's work from psock's deferred destructor:
Stop psock's parser just before canceling its work.
Fixes: 1d79895aef18 ("sk_msg: Always cancel strp work before freeing the psock") Reported-by: kernel test robot <rong.a.chen@intel.com> Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiner reported that the commit in question prevents his network adapter
from triggering PME and waking up when network cable is plugged.
The commit tried to prevent root port waking up from D3cold immediately but
looks like disabing root port PME interrupt is not the right way to fix
that issue so revert it now. The patch following proposes an alternative
solution to that issue.
When an rc device is created, we do not know what key codes it will
support, since a new keymap might be loaded at some later point. So,
we set all keybit in the input device.
The uevent for the input device includes all the key codes, of which
there are now 768. This overflows the size of the uevent
(UEVENT_BUFFER_SIZE) and no event is generated.
Revert for now until we figure out a different solution.
The DRM driver stack is designed to work with cache coherent devices
only, but permits an optimization to be enabled in some cases, where
for some buffers, both the CPU and the GPU use uncached mappings,
removing the need for DMA snooping and allocation in the CPU caches.
The use of uncached GPU mappings relies on the correct implementation
of the PCIe NoSnoop TLP attribute by the platform, otherwise the GPU
will use cached mappings nonetheless. On x86 platforms, this does not
seem to matter, as uncached CPU mappings will snoop the caches in any
case. However, on ARM and arm64, enabling this optimization on a
platform where NoSnoop is ignored results in loss of coherency, which
breaks correct operation of the device. Since we have no way of
detecting whether NoSnoop works or not, just disable this
optimization entirely for ARM and arm64.
Cc: Christian Koenig <christian.koenig@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: David Zhou <David1.Zhou@amd.com> Cc: Huang Rui <ray.huang@amd.com> Cc: Junwei Zhang <Jerry.Zhang@amd.com> Cc: Michel Daenzer <michel.daenzer@amd.com> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: Sean Paul <sean@poorly.run> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Will Deacon <will.deacon@arm.com> Cc: Christoph Hellwig <hch@infradead.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: amd-gfx list <amd-gfx@lists.freedesktop.org> Cc: dri-devel <dri-devel@lists.freedesktop.org> Reported-by: Carsten Haitzler <Carsten.Haitzler@arm.com> Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Link: https://patchwork.kernel.org/patch/10778815/ Signed-off-by: Christian König <christian.koenig@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The maximum voltage value for buck8 regulator on Odroid XU3/XU4 boards is
set too low. Increase it to the 2000mV as specified on the board schematic.
So far the board worked fine, because of the bug in the PMIC driver, which
used incorrect step value for that regulator. It interpreted the voltage
value set by the bootloader as 1225mV and kept it unchanged. The regulator
driver has been however fixed recently in the commit 56b5d4ea778c
("regulator: s2mps11: Fix steps for buck7, buck8 and LDO35"), what results
in reading the proper buck8 value and forcing it to 1500mV on boot. This
is not enough for proper board operation and results in eMMC errors during
heavy IO traffic. Increasing maximum voltage value for buck8 restores
original driver behavior and fixes eMMC issues.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 86a2d2ac5e5d ("ARM: dts: Add dts file for Odroid XU3 board") Fixes: 56b5d4ea778c ("regulator: s2mps11: Fix steps for buck7, buck8 and LDO35") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 225da7e65a03 ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7cd2 ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org> Reported-by: Markus Reichl <m.reichl@fivetechno.de> Suggested-by: Ulf Hansson <ulf.hansson@linaro.org> Fixes: 225da7e65a03 ("ARM: dts: add eMMC reset line for exynos4412-odroid-common") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Somewhere along recent changes to power control of the wl1835, power-on
became very unreliable on the hikey, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms, the
hikey would already be happy with 1 ms. Still, we use the safer 10 ms,
like on the Ultra96.
Somewhere along recent changes to power control of the wl1831, power-on
became very unreliable on the Ultra96, failing like this:
wl1271_sdio: probe of mmc2:0001:1 failed with error -16
wl1271_sdio: probe of mmc2:0001:2 failed with error -16
After playing with some dt parameters and comparing to other users of
this chip, it turned out we need some power-on delay to make things
stable again. In contrast to those other users which define 200 ms,
Ultra96 is already happy with 10 ms.
Fixes: 5869ba0653b9 ("arm64: zynqmp: Add support for Xilinx zcu100-revC") Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On Denverton's integration of the Intel(R) Trace Hub (for a reference and
overview see Documentation/trace/intel_th.rst) the reported size of one of
its resources (RTIT_BAR) doesn't match its actual size, which leads to
overlaps with other devices' resources.
In practice, it overlaps with XHCI MMIO space, which results in the xhci
driver bailing out after seeing its registers as 0xffffffff, and perceived
disappearance of all USB devices:
intel_th_pci 0000:00:1f.7: enabling device (0004 -> 0006)
xhci_hcd 0000:00:15.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:15.0: xHC not responding in xhci_irq, assume controller is dead
xhci_hcd 0000:00:15.0: HC died; cleaning up
usb 1-1: USB disconnect, device number 2
For this reason, we need to resize the RTIT_BAR on Denverton to its actual
size, which in this case is 4MB. The corresponding erratum is DNV36 at the
link below:
DNV36. Processor Host Root Complex May Incorrectly Route Memory
Accesses to Intel® Trace Hub
Problem: The Intel® Trace Hub RTIT_BAR (B0:D31:F7 offset 20h) is
reported as a 2KB memory range. Due to this erratum, the
processor Host Root Complex will forward addresses from
RTIT_BAR to RTIT_BAR + 4MB -1 to Intel® Trace Hub.
Implication: Devices assigned within the RTIT_BAR to RTIT_BAR + 4MB -1
space may not function correctly.
Workaround: A BIOS code change has been identified and may be
implemented as a workaround for this erratum.
Status: No Fix.
Note that 5118ccd34780 ("intel_th: pci: Add Denverton SOC support") updates
the Trace Hub driver so it claims the Denverton device, but the resource
overlap exists regardless of whether that driver is loaded or that commit
is included.
When initially testing the Camera Terminal Descriptor wTerminalType
field (buffer[4]), no mask is used. Later in the function, the MSB is
overloaded to store the descriptor subtype, and so a mask of 0x7fff
is used to check the type.
If a descriptor is specially crafted to set this overloaded bit in the
original wTerminalType field, the initial type check will fail (falling
through, without adjusting the buffer size), but the later type checks
will pass, assuming the buffer has been made suitably large, causing an
overflow.
Avoid this problem by checking for the MSB in the wTerminalType field.
If the bit is set, assume the descriptor is bad, and abort parsing it.
Originally reported here:
https://groups.google.com/forum/#!topic/syzkaller/Ot1fOE6v1d8
A similar (non-compiling) patch was provided at that time.
With commit e16337622016 ("Bluetooth: Handle bt_accept_enqueue() socket
atomically") lock_sock[_nested]() is used to acquire the socket lock
before manipulating the socket. lock_sock[_nested]() may block, which
is problematic since bt_accept_enqueue() can be called in bottom half
context (e.g. from rfcomm_connect_ind()):
Add a parameter to bt_accept_enqueue() to indicate whether the
function is called from BH context, and acquire the socket lock
with bh_lock_sock_nested() if that's the case.
Also adapt all callers of bt_accept_enqueue() to pass the new
parameter:
- l2cap_sock_new_connection_cb()
- uses lock_sock() to lock the parent socket => process context
- rfcomm_connect_ind()
- acquires the parent socket lock with bh_lock_sock() => BH
context
- __sco_chan_add()
- called from sco_chan_add(), which is called from sco_connect().
parent is NULL, hence bt_accept_enqueue() isn't called in this
code path and we can ignore it
- also called from sco_conn_ready(). uses bh_lock_sock() to acquire
the parent lock => BH context
Realtek bluetooth may not work after reboot:
[ 12.446130] Bluetooth: hci0: RTL: rtl: unknown IC info, lmp subver a99e, hci rev 826c, hci ver 0008
This is a regression introduced by commit 26503ad25de8 ("Bluetooth:
btrtl: split the device initialization into smaller parts"). The new
logic errors out early when no matching IC info can be found, in this
case it means the firmware is already loaded.
So let's assume the firmware is already loaded when we can't find
matching IC info, like the old logic did.
commit a6a9be9270c87 ("selftests: firmware: return Kselftest Skip code
for skipped tests") by Shuah modified failures to return the special
error code of $ksft_skip (4). We have a corner case issue where we
*do* want to verify_reqs().
This breaks testing on Debian, and this patch was NACKed anyway.
The proper way to address this is a quirk for busybox as that is
where the issue is present.
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Fixes: f70b472e937b ("selftests: firmware: remove use of non-standard diff -Z option") Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit tried to address an issue discovered by Dan where he got
a message saying:
'usermode helper disabled so ignoring test'.
Dans's commit is forcing CONFIG_FW_LOADER_USER_HELPER_FALLBACK but just
having CONFIG_FW_LOADER_USER_HELPER suffices to emulate the_FALLBACK
functionality.
Dan's commit is trying to fix an issue which is hidden from a previous
commit. That issue will be addressed properly next.
Fixes: 7492902e8d22 ("selftests: firmware: add CONFIG_FW_LOADER_USER_HELPER_FALLBACK to config") Cc: stable <stable@vger.kernel.org> Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current GPIO code in cp210x fails to take USB autosuspend into account,
making it practically impossible to use GPIOs with autosuspend enabled
without user configuration. Fix this like for ftdi_sio in a previous patch.
Tested on a CP2102N.
Signed-off-by: Karoly Pados <pados@pados.hu> Fixes: cf5276ce7867 ("USB: serial: cp210x: Adding GPIO support for CP2105") Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stack unwinding is implemented incorrectly in xtensa get_wchan: instead
of extracting a0 and a1 registers from the spill location under the
stack pointer it extracts a word pointed to by the stack pointer and
subtracts 4 or 3 from it.
Cc: stable@vger.kernel.org Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wake_up_locked() may but does not have to be called with interrupts
disabled. Since the fuse filesystem calls wake_up_locked() without
disabling interrupts aio_poll_wake() may be called with interrupts
enabled. Since the kioctx.ctx_lock may be acquired from IRQ context,
all code that acquires that lock from thread context must disable
interrupts. Hence change the spin_trylock() call in aio_poll_wake()
into a spin_trylock_irqsave() call. This patch fixes the following
lockdep complaint:
The irq_pages is the number of pages for irq stack, but not the
order which is needed by __get_free_pages().
We can use get_order() to calculate the accurate order.
Fix this by sanitizing IndexCard before using it to index apbs.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
During initialization, the host and super-speed power domains will
contain an ERR_PTR() encoded error code rather than being NULL. To
avoid a crash, use a !IS_ERR_OR_NULL() condition during cleanup.
Then tracing syscall exit event it is extremely useful to filter exit
codes equal to some negative value, to react only to required errors.
But negative numbers does not work:
[root@snorch sys_exit_read]# echo "ret == -1" > filter
bash: echo: write error: Invalid argument
[root@snorch sys_exit_read]# cat filter
ret == -1
^
parse_error: Invalid value (did you forget quotes)?
Similar thing happens when setting triggers.
These is a regression in v4.17 introduced by the commit mentioned below,
testing without these commit shows no problem with negative numbers.
Link: http://lkml.kernel.org/r/20180823102534.7642-1-ptikhomirov@virtuozzo.com Cc: stable@vger.kernel.org Fixes: 80765597bc58 ("tracing: Rewrite filter logic to be simpler and faster") Signed-off-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix regression bug introduced in
commit 365ad353c256 ("tipc: reduce risk of user starvation during link
congestion")
Only signal -EDESTADDRREQ for RDM/DGRAM if we don't have a cached
sockaddr.
Fixes: 365ad353c256 ("tipc: reduce risk of user starvation during link congestion") Signed-off-by: Erik Hugne <erik.hugne@gmail.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The user msg is also copied to the abort packet when doing SCTP_ABORT in
sctp_sendmsg_check_sflags(). When SCTP_SENDALL is set, iov_iter_revert()
should have been called for sending abort on the next asoc with copying
this msg. Otherwise, memcpy_from_msg() in sctp_make_abort_user() will
fail and return error.
Fixes: 4910280503f3 ("sctp: add support for snd flag SCTP_SENDALL process in sendmsg") Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quectel EG12 (module)/EM12 (M.2 card) is a Cat. 12 LTE modem. The modem
behaves in the same way as the EP06, so the "set DTR"-quirk must be
applied and the diagnostic-interface check performed. Since the
diagnostic-check now applies to more modems, I have renamed the function
from quectel_ep06_diag_detected() to quectel_diag_detected().
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> Acked-by: Bjørn Mork <bjorn@mork.no> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the series fc8b81a5981f ("Merge branch 'lockless-qdisc-series'")
John made the assumption that the data path had no need to read
the qdisc qlen (number of packets in the qdisc).
It is true when pfifo_fast is used as the root qdisc, or as direct MQ/MQPRIO
children.
But pfifo_fast can be used as leaf in class full qdiscs, and existing
logic needs to access the child qlen in an efficient way.
HTB breaks badly, since it uses cl->leaf.q->q.qlen in :
htb_activate() -> WARN_ON()
htb_dequeue_tree() to decide if a class can be htb_deactivated
when it has no more packets.
HFSC, DRR, CBQ, QFQ have similar issues, and some calls to
qdisc_tree_reduce_backlog() also read q.qlen directly.
Using qdisc_qlen_sum() (which iterates over all possible cpus)
in the data path is a non starter.
It seems we have to put back qlen in a central location,
at least for stable kernels.
For all qdisc but pfifo_fast, qlen is guarded by the qdisc lock,
so the existing q.qlen{++|--} are correct.
For 'lockless' qdisc (pfifo_fast so far), we need to use atomic_{inc|dec}()
because the spinlock might be not held (for example from
pfifo_fast_enqueue() and pfifo_fast_dequeue())
This patch adds atomic_qlen (in the same location than qlen)
and renames the following helpers, since we want to express
they can be used without qdisc lock, and that qlen is no longer percpu.
Later (net-next) we might revert this patch by tracking all these
qlen uses and replace them by a more efficient method (not having
to access a precise qlen, but an empty/non_empty status that might
be less expensive to maintain/track).
Another possibility is to have a legacy pfifo_fast version that would
be used when used a a child qdisc, since the parent qdisc needs
a spinlock anyway. But then, future lockless qdiscs would also
have the same problem.
Fixes: 7e66016f2c65 ("net: sched: helpers to sum qlen and qlen for per cpu logic") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jiri Pirko <jiri@resnulli.us> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ports 9 and 10 don't have internal PHY's but are (dependent on the
version) SERDES/SGMII/XAUI/RXAUI ports.
v2:
- fix it for all 88E6x90 family members
Fixes: bc3931557d1d ("net: dsa: mv88e6xxx: Add number of internal PHYs") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When testing another issue I faced the problem that
mv88e6xxx_port_setup_mac() failed due to DUPLEX_UNKNOWN being passed
as argument to mv88e6xxx_port_set_duplex(). We should handle this case
gracefully and return -EOPNOTSUPP, like e.g. mv88e6xxx_port_set_speed()
is doing it.
Fixes: 7f1ae07b51e8 ("net: dsa: mv88e6xxx: add port duplex setter") Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log