memblock.{reserved,memory}.regions may be allocated using kmalloc() in
memblock_double_array(). Use kfree() to release these kmalloced regions
indicated by memblock_{reserved,memory}_in_slab.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Fixes: 3010f876500f ("mm: discard memblock data later") Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tegra186 GPIO driver makes the assumption that the pointer
returned by irq_data_get_irq_chip_data() is a pointer to a
tegra_gpio structure. Unfortunately, it is actually a pointer
to the inner gpio_chip structure, as mandated by the gpiolib
infrastructure. Nice try.
The saving grace is that the gpio_chip is the first member of
tegra_gpio, so the bug has gone undetected since... forever.
Fix it by performing a container_of() on the pointer. This results
in no additional code, and makes it possible to understand how
the whole thing works.
In the current implementation the user may open a virtual tty which then
could fail to establish the underlying DLCI. The function gsmtty_open()
gets stuck in tty_port_block_til_ready() while waiting for a carrier rise.
This happens if the remote side fails to acknowledge the link establishment
request in time or completely. At some point gsm_dlci_close() is called
to abort the link establishment attempt. The function tries to inform the
associated virtual tty by performing a hangup. But the blocking loop within
tty_port_block_til_ready() is not informed about this event.
The patch proposed here fixes this by resetting the initialization state of
the virtual tty to ensure the loop exits and triggering it to make
tty_port_block_til_ready() return.
tty flow control is handled via gsmtty_throttle() and gsmtty_unthrottle().
Both functions propagate the outgoing hardware flow control state to the
remote side via MSC (modem status command) frames. The local state is taken
from the RTS (ready to send) flag of the tty. However, RTS gets mapped to
DTR (data terminal ready), which is wrong.
This patch corrects this by mapping RTS to RTS.
The here fixed commit made the tty hangup asynchronous to avoid a circular
locking warning. I could not reproduce this warning. Furthermore, due to
the asynchronous hangup the function call now gets queued up while the
underlying tty is being freed. Depending on the timing this results in a
NULL pointer access in the global work queue scheduler. To be precise in
process_one_work(). Therefore, the previous commit made the issue worse
which it tried to fix.
This patch fixes this by falling back to the old behavior which uses a
blocking tty hangup call before freeing up the associated tty.
Fixes: 7030082a7415 ("tty: n_gsm: avoid recursive locking with async port hangup") Cc: stable@vger.kernel.org Signed-off-by: Daniel Starke <daniel.starke@siemens.com> Link: https://lore.kernel.org/r/20220218073123.2121-4-daniel.starke@siemens.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to open a DLCI by sending a SABM frame may fail with a timeout.
The link is closed on the initiator side without informing the responder
about this event. The responder assumes the link is open after sending a
UA frame to answer the SABM frame. The link gets stuck in a half open
state.
This patch fixes this by initiating the proper link termination procedure
after link setup timeout instead of silently closing it down.
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.4.6.3.7 describes the encoding of the
control signal octet used by the MSC (modem status command). The same
encoding is also used in convergence layer type 2 as described in chapter
5.5.2. Table 7 and 24 both require the DV (data valid) bit to be set 1 for
outgoing control signal octets sent by the DTE (data terminal equipment),
i.e. for the initiator side.
Currently, the DV bit is only set if CD (carrier detect) is on, regardless
of the side.
This patch fixes this behavior by setting the DV bit on the initiator side
unconditionally.
The trace_hardirqs_{on,off}() require the caller to setup frame pointer
properly. This because these two functions use macro 'CALLER_ADDR1' (aka.
__builtin_return_address(1)) to acquire caller info. If the $fp is used
for other purpose, the code generated this macro (as below) could trigger
memory access fault.
If the state is not idle then resolve_prepare_src() should immediately
fail and no change to global state should happen. However, it
unconditionally overwrites the src_addr trying to build a temporary any
address.
For instance if the state is already RDMA_CM_LISTEN then this will corrupt
the src_addr and would cause the test in cma_cancel_operation():
if (cma_any_addr(cma_src_addr(id_priv)) && !id_priv->cma_dev)
Which would manifest as this trace from syzkaller:
BUG: KASAN: use-after-free in __list_add_valid+0x93/0xa0 lib/list_debug.c:26
Read of size 8 at addr ffff8881546491e0 by task syz-executor.1/32204
This is indicating that an rdma_id_private was destroyed without doing
cma_cancel_listens().
Instead of trying to re-use the src_addr memory to indirectly create an
any address derived from the dst build one explicitly on the stack and
bind to that as any other normal flow would do. rdma_bind_addr() will copy
it over the src_addr once it knows the state is valid.
This is similar to commit bc0bdc5afaa7 ("RDMA/cma: Do not change
route.addr.src_addr.ss_family")
Link: https://lore.kernel.org/r/0-v2-e975c8fd9ef2+11e-syz_cma_srcaddr_jgg@nvidia.com Cc: stable@vger.kernel.org Fixes: 732d41c545bb ("RDMA/cma: Make the locking for automatic state transition more clear") Reported-by: syzbot+c94a3675a626f6333d74@syzkaller.appspotmail.com Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When unbinding/binding a driver with DMA mapped memory, the DMA map is
not freed before the driver is reloaded. This leads to a memory leak
when the DMA map is overwritten when reprobing the driver.
This can be reproduced with a platform driver having a dma-range:
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
When HCE(Host Controller Error) is set, it means an internal
error condition has been detected. Software needs to re-initialize
the HC, so add this check in xhci resume.
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources") Cc: stable <stable@vger.kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Dell DW5829e same as DW5821e except CAT level.
DW5821e supports CAT16 but DW5829e supports CAT9.
There are 2 types product of DW5829e: normal and eSIM.
So we will add 2 PID for DW5829e.
And for each PID, it support MBIM or RMNET.
Let's see test evidence as below:
BTW, the interface 0x6 of MBIM mode is GNSS port, which not same as NMEA
port. So it's banned from serial option driver.
The remaining interfaces 0x2-0x5 are: MODEM, MODEM, NMEA, DIAG.
Signed-off-by: Slark Xiao <slark_xiao@163.com> Link: https://lore.kernel.org/r/20220214021401.6264-1-slark_xiao@163.com
[ johan: drop unnecessary reservation of interface 1 ] Cc: stable@vger.kernel.org Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Al Viro brought it to my attention that the dentries may not be filled
when the parse_options() is called, causing the call to set_gid() to
possibly crash. It should only be called if parse_options() succeeds
totally anyway.
He suggested the logical place to do the update is in apply_options().
There's no lock for rndis response list. It could cause list corruption
if there're two different list_add at the same time like below.
It's better to add in rndis_add_response / rndis_free_response
/ rndis_get_next_response to prevent any race condition on response list.
CH341 has Product ID 0x5512 in EPP/MEM mode which is used for
I2C/SPI/GPIO interfaces. In asynchronous serial interface mode
CH341 has PID 0x5523 which is already in the table.
The HPT371 chip physically has only one channel, the secondary one,
however the primary channel registers do exist! Thus we have to
manually disable the non-existing channel if the BIOS hasn't done this
already. Similarly to the pata_hpt3x2n driver, always disable the
primary channel.
Fixes: 669a5db411d8 ("[libata] Add a bunch of PATA drivers.") Cc: stable@vger.kernel.org Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART drivers are meant to use the port spinlock within certain
methods, to protect against reentrancy. The sc16is7xx driver does
very little locking, presumably because when added it triggers
"scheduling while atomic" errors. This is due to the use of mutexes
within the regmap abstraction layer, and the mutex implementation's
habit of sleeping the current thread while waiting for access.
Unfortunately this lack of interlocking can lead to corruption of
outbound data, which occurs when the buffer used for I2C transmission
is used simultaneously by two threads - a work queue thread running
sc16is7xx_tx_proc, and an IRQ thread in sc16is7xx_port_irq, both
of which can call sc16is7xx_handle_tx.
An earlier patch added efr_lock, a mutex that controls access to the
EFR register. This mutex is already claimed in the IRQ handler, and
all that is required is to claim the same mutex in sc16is7xx_tx_proc.
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fix this problem for the following drivers: bmc150, bmg160, kmx61,
kxcj-1013, mma9551, mma9553.
Fixes: 7d0ead5c3f00 ("iio: Reconcile operation order between iio_register/unregister and pm functions") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20220106112309.16879-1-linmq006@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a trigger is set on an event to disable or enable tracing within an
instance, then tracing should be disabled or enabled in the instance and
not at the top level, which is confusing to users.
Link: https://lkml.kernel.org/r/20220223223837.14f94ec3@rorschach.local.home Cc: stable@vger.kernel.org Fixes: ae63b31e4d0e2 ("tracing: Separate out trace events from global variables") Tested-by: Daniel Bristot de Oliveira <bristot@kernel.org> Reviewed-by: Tom Zanussi <zanussi@kernel.org> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the flush_workqueue(system_long_wq) call since flushing
system_long_wq is deadlock-prone and since that call is redundant with a
preceding cancel_work_sync()
Link: https://lore.kernel.org/r/20220215210511.28303-3-bvanassche@acm.org Fixes: ef6c49d87c34 ("IB/srp: Eliminate state SRP_TARGET_DEAD") Reported-by: syzbot+831661966588c802aae9@syzkaller.appspotmail.com Signed-off-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When configfs_register_subsystem() or configfs_unregister_subsystem()
is executing link_group() or unlink_group(),
it is possible that two processes add or delete list concurrently.
Some unfortunate interleavings of them can cause kernel panic.
One of cases is:
A --> B --> C --> D
A <-- B <-- C <-- D
Fix this by adding mutex when calling link_group() or unlink_group(),
but parent configfs_subsystem is NULL when config_item is root.
So I create a mutex configfs_subsystem_mutex.
Error path of rtrs_clt_open() calls free_clt(), where free_permit is
called. This is wrong since error path of rtrs_clt_open() does not need
to call free_permit().
Also, moving free_permits() call to rtrs_clt_close(), makes it more
aligned with the call to alloc_permit() in rtrs_clt_open().
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Link: https://lore.kernel.org/r/20220217030929.323849-2-haris.iqbal@ionos.com Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com> Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Callback function rtrs_clt_dev_release() for put_device() calls kfree(clt)
to free memory. We shouldn't call kfree(clt) again, and we can't use the
clt after kfree too.
Replace device_register() with device_initialize() and device_add() so that
dev_set_name can() be used appropriately.
Move mutex_destroy() to the release function so it can be called in
the alloc_clt err path.
Fixes: eab098246625 ("RDMA/rtrs-clt: Refactor the failure cases in alloc_clt") Link: https://lore.kernel.org/r/20220217030929.323849-1-haris.iqbal@ionos.com Reported-by: Miaoqian Lin <linmq006@gmail.com> Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com> Reviewed-by: Jack Wang <jinpu.wang@ionos.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
With the existing logic where clear_ack is true (HW doesn’t support
auto clear for ICR), interrupt clear register reset is not handled
properly. Due to this only the first interrupts get processed properly
and further interrupts are blocked due to not resetting interrupt
clear register.
Example for issue case where Invert_ack is false and clear_ack is true:
Say Default ISR=0x00 & ICR=0x00 and ISR is triggered with 2
interrupts making ISR = 0x11.
Step 1: Say ISR is set 0x11 (store status_buff = ISR). ISR needs to
be cleared with the help of ICR once the Interrupt is processed.
Step 2: Write ICR = 0x11 (status_buff), this will clear the ISR to 0x00.
Step 3: Issue - In the existing code, ICR is written with ICR =
~(status_buff) i.e ICR = 0xEE -> This will block all the interrupts
from raising except for interrupts 0 and 4. So expectation here is to
reset ICR, which will unblock all the interrupts.
if (chip->clear_ack) {
if (chip->ack_invert && !ret)
........
else if (!ret)
ret = regmap_write(map, reg,
~data->status_buf[i]);
So writing 0 and 0xff (when ack_invert is true) should have no effect, other
than clearing the ACKs just set.
Fixes: 3a6f0fb7b8eb ("regmap: irq: Add support to clear ack registers") Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Link: https://lore.kernel.org/r/20220217085007.30218-1-quic_pkumpatl@quicinc.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In zynq_qspi_exec_mem_op(), kzalloc() is directly used in memset(),
which could lead to a NULL pointer dereference on failure of
kzalloc().
Fix this bug by adding a check of tmpbuf.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_SPI_ZYNQ_QSPI=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 67dca5e580f1 ("spi: spi-mem: Add support for Zynq QSPI controller") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Link: https://lore.kernel.org/r/20211130172253.203700-1-zhou1615@umn.edu Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For RX TLS device-offloaded packets, the HW spec guarantees checksum
validation for the offloaded packets, but does not define whether the
CQE.checksum field matches the original packet (ciphertext) or
the decrypted one (plaintext). This latitude allows architetctural
improvements between generations of chips, resulting in different decisions
regarding the value type of CQE.checksum.
Hence, for these packets, the device driver should not make use of this CQE
field. Here we block CHECKSUM_COMPLETE usage for RX TLS device-offloaded
packets, and use CHECKSUM_UNNECESSARY instead.
Value of the packet's tcp_hdr.csum is not modified by the HW, and it always
matches the original ciphertext.
Match metadata support check returns false for ecpf device.
However, this support does exist for ecpf and therefore this
limitation should be removed to allow feature such as stacked
devices and internal port offloaded to be supported.
This test is checking if we exited the list via break or not. However
if it did not exit via a break then "node" does not point to a valid
udp_tunnel_nic_shared_node struct. It will work because of the way
the structs are laid out it's the equivalent of
"if (info->shared->udp_tunnel_nic_info != dev)" which will always be
true, but it's not the right way to test.
Fixes: 74cc6d182d03 ("udp_tunnel: add the ability to share port tables") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The battery on the 2nd hand Surface 3 which I recently bought appears to
not have a serial number programmed in. This results in any I2C reads from
the registers containing the serial number failing with an I2C NACK.
This was causing mshw0011_bix() to fail causing the battery readings to
not work at all.
Ignore EREMOTEIO (I2C NACK) errors when retrieving the serial number and
continue with an empty serial number to fix this.
All functions defined as static inline in net/checksum.h are
meant to be inlined for performance reason.
But since commit ac7c3e4ff401 ("compiler: enable
CONFIG_OPTIMIZE_INLINING forcibly") the compiler is allowed to
uninline functions when it wants.
Fair enough in the general case, but for tiny performance critical
checksum helpers that's counter-productive.
The problem mainly arises when selecting CONFIG_CC_OPTIMISE_FOR_SIZE,
Those helpers being 'static inline' in header files you suddenly find
them duplicated many times in the resulting vmlinux.
Here is a typical exemple when building powerpc pmac32_defconfig
with CONFIG_CC_OPTIMISE_FOR_SIZE. csum_sub() appears 4 times:
devm_kmalloc() returns a pointer to allocated memory on success, NULL
on failure. While lp->indirect_lock is allocated by devm_kmalloc()
without proper check. It is better to check the value of it to
prevent potential wrong memory access.
Fixes: f14f5c11f051 ("net: ll_temac: Support indirect_mutex share within TEMAC IP") Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flow table lookup is skipped if packet either went through ct clear
action (which set the IP_CT_UNTRACKED flag on the packet), or while
switching zones and there is already a connection associated with
the packet. This will result in no SW offload of the connection,
and the and connection not being removed from flow table with
TCP teardown (fin/rst packet).
To fix the above, remove these unneccary checks in flow
table lookup.
Fixes: 46475bb20f4b ("net/sched: act_ct: Software offload of established flows") Signed-off-by: Paul Blakey <paulb@nvidia.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to fill the drm_display_info structure each time an EDID is
read, the code currently will call drm_add_display_info with the parsed
EDID.
drm_add_display_info will then call drm_reset_display_info to reset all
the fields to 0, and then set them to the proper value depending on the
EDID.
In the color_formats case, we will thus report that we don't support any
color format, and then fill it back with RGB444 plus the additional
formats described in the EDID Feature Support byte.
However, since that byte only contains format-related bits since the 1.4
specification, this doesn't happen if the EDID is following an earlier
specification. In turn, it means that for one of these EDID, we end up
with color_formats set to 0.
The EDID 1.3 specification never really specifies what it means by RGB
exactly, but since both HDMI and DVI will use RGB444, it's fairly safe
to assume it's supposed to be RGB444.
Let's move the addition of RGB444 to color_formats earlier in
drm_add_display_info() so that it's always set for a digital display.
Fixes: da05a5a71ad8 ("drm: parse color format support for digital displays") Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Reported-by: Matthias Reichl <hias@horus.com> Signed-off-by: Maxime Ripard <maxime@cerno.tech> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220203115416.1137308-1-maxime@cerno.tech Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ipv6 ttl, label and tos fields are modified without first
pulling/pushing the ipv6 header, which would have updated
the hw csum (if available). This might cause csum validation
when sending the packet to the stack, as can be seen in
the trace below.
We encounter a tcp drop issue in our cloud environment. Packet GROed in
host forwards to a VM virtio_net nic with net_failover enabled. VM acts
as a IPVS LB with ipip encapsulation. The full path like:
host gro -> vm virtio_net rx -> net_failover rx -> ipvs fullnat
-> ipip encap -> net_failover tx -> virtio_net tx
When net_failover transmits a ipip pkt (gso_type = 0x0103, which means
SKB_GSO_TCPV4, SKB_GSO_DODGY and SKB_GSO_IPXIP4), there is no gso
did because it supports TSO and GSO_IPXIP4. But network_header points to
inner ip header.
Afterwards virtio_net transmits the pkt, only inner ip header is modified.
And the outer one just keeps unchanged. The pkt will be dropped in remote
host.
The root cause of this issue is specific with the rare combination of
SKB_GSO_DODGY and a tunnel device that adds an SKB_GSO_ tunnel option.
SKB_GSO_DODGY is set from external virtio_net. We need to reset network
header when callbacks.gso_segment() returns NULL.
This patch also includes ipv6_gso_segment(), considering SIT, etc.
Fixes: cb32f511a70b ("ipip: add GSO/TSO support") Signed-off-by: Tao Liu <thomas.liu@ucloud.cn> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These tests are supposed to check if the loop exited via a break or not.
However the tests are wrong because if we did not exit via a break then
"p" is not a valid pointer. In that case, it's the equivalent of
"if (*(u32 *)sr == *last_key) {". That's going to work most of the time,
but there is a potential for those to be equal.
Fixes: 1593123a6a49 ("tipc: add name table dump to new netlink api") Fixes: 1a1a143daf84 ("tipc: add publication dump to new netlink api") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bpf_msg_push_data may return a non-zero value to indicate an error. The
return value should be checked to prevent undetected errors.
To indicate an error, the BPF programs now perform a different action
than their intended one to make the userspace test program notice the
error, i.e., the programs supposed to pass/redirect drop, the program
supposed to drop passes.
If bpf_msg_push_data() is called with len 0 (as it happens during
selftests/bpf/test_sockmap), we do not need to do anything and can
return early.
Calling bpf_msg_push_data() with len 0 previously lead to a wrong ENOMEM
error: we later called get_order(copy + len); if len was 0, copy + len
was also often 0 and get_order() returned some undefined value (at the
moment 52). alloc_pages() caught that and failed, but then bpf_msg_push_data()
returned ENOMEM. This was wrong because we are most probably not out of
memory and actually do not need any additional memory.
Fixes: 6fff607e2f14b ("bpf: sk_msg program helper bpf_msg_push_data") Signed-off-by: Felix Maurer <fmaurer@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yhs@fb.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/df69012695c7094ccb1943ca02b4920db3537466.1644421921.git.fmaurer@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If an attempt is made to a sensor with a thermal zone and it fails,
the call to devm_thermal_zone_of_sensor_register() may return -ENODEV.
This may result in crashes similar to the following.
The hwmon core needs to handle all errors returned from calls
to devm_thermal_zone_of_sensor_register(). If the call fails
with -ENODEV, report that the sensor was not attached to a
thermal zone but continue to register the hwmon device.
ethtool --show-fec <interface> does not show anything when the Active
FEC setting in the chip is set to None. Fix it to properly return
ETHTOOL_FEC_OFF in that case.
Fixes: 8b2775890ad8 ("bnxt_en: Report FEC settings to ethtool.") Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0") added
new firmware support in the driver with maintaining older firmware
compatibility. However, older firmware was not added in MODULE_FIRMWARE()
which caused missing firmware files in initrd image leading to driver load
failure from initrd. This patch adds MODULE_FIRMWARE() for older firmware
version to have firmware files included in initrd.
When perf_data__create_dir() fails, it calls close_dir(), but
perf_session__delete() also calls close_dir() and since dir.version and
dir.nr were initialized by perf_data__create_dir(), a double free occurs.
This patch moves the initialization of dir.version and dir.nr after
successful initialization of dir.files, that prevents double freeing.
This behavior is already implemented in perf_data__open_dir().
Fixes: 145520631130bd64 ("perf data: Add perf_data__(create_dir|close_dir) functions") Signed-off-by: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Antonov <alexander.antonov@linux.intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexei Budankov <abudankov@huawei.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: https://lore.kernel.org/r/20220218152341.5197-2-alexey.v.bayduraev@linux.intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As Jakub noticed, prints should be avoided on the datapath.
Also, as packets would never come to the else branch in
ping_lookup(), remove pr_err() from ping_lookup().
Adds a driver private tee_context by moving the tee_context in struct
optee_notif to struct optee. This tee_context was previously used when
doing internal calls to secure world to deliver notification.
The new driver internal tee_context is now also when allocating driver
private shared memory. This decouples the shared memory object from its
original tee_context. This is needed when the life time of such a memory
allocation outlives the client tee_context.
This patch fixes the problem described below:
The addition of a shutdown hook by commit f25889f93184 ("optee: fix tee out
of memory failure seen during kexec reboot") introduced a kernel shutdown
regression that can be triggered after running the OP-TEE xtest suites.
Once the shutdown hook is called it is not possible to communicate any more
with the supplicant process because the system is not scheduling task any
longer. Thus if the optee driver shutdown path receives a supplicant RPC
request from the OP-TEE we will deadlock the kernel's shutdown.
Fixes: f25889f93184 ("optee: fix tee out of memory failure seen during kexec reboot") Fixes: 217e0250cccb ("tee: use reference counting for tee_context") Reported-by: Lars Persson <larper@axis.com> Cc: stable@vger.kernel.org Reviewed-by: Sumit Garg <sumit.garg@linaro.org> Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
[JW: backport to 5.10-stable + update commit message] Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Brian Geffon [Tue, 15 Feb 2022 19:22:33 +0000 (11:22 -0800)]
x86/fpu: Correct pkru/xstate inconsistency
When eagerly switching PKRU in switch_fpu_finish() it checks that
current is not a kernel thread as kernel threads will never use PKRU.
It's possible that this_cpu_read_stable() on current_task
(ie. get_current()) is returning an old cached value. To resolve this
reference next_p directly rather than relying on current.
As written it's possible when switching from a kernel thread to a
userspace thread to observe a cached PF_KTHREAD flag and never restore
the PKRU. And as a result this issue only occurs when switching
from a kernel thread to a userspace thread, switching from a non kernel
thread works perfectly fine because all that is considered in that
situation are the flags from some other non kernel task and the next fpu
is passed in to switch_fpu_finish().
This behavior only exists between 5.2 and 5.13 when it was fixed by a
rewrite decoupling PKRU from xstate, in:
commit 954436989cc5 ("x86/fpu: Remove PKRU handling from switch_fpu_finish()")
Unfortunately backporting the fix from 5.13 is probably not realistic as
it's part of a 60+ patch series which rewrites most of the PKRU handling.
Fixes: 0cecca9d03c9 ("x86/fpu: Eager switch PKRU state") Signed-off-by: Brian Geffon <bgeffon@google.com> Signed-off-by: Willis Kung <williskung@google.com> Tested-by: Willis Kung <williskung@google.com> Cc: <stable@vger.kernel.org> # v5.4.x Cc: <stable@vger.kernel.org> # v5.10.x Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A broken device may give an extreme offset like 0xFFF0
and a reasonable length for a fragment. In the sanity
check as formulated now, this will create an integer
overflow, defeating the sanity check. Both offset
and offset + len need to be checked in such a manner
that no overflow can occur.
And those quantities should be unsigned.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Oliver Neukum <oneukum@suse.com> Reported-by: Ross Maynard <bids.7405@bigpond.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=215361 Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A malicious device can leak heap data to user space
providing bogus frame lengths. Introduce a sanity check.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Reviewed-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When changing between SAGV vs. no SAGV on tgl+ we have to
update the use_sagv_wm flag for all the crtcs or else
an active pipe not already in the state will end up using
the wrong watermarks. That is especially bad when we end up
with the tighter non-SAGV watermarks with SAGV enabled.
Usually ends up in underruns.
In current async pagefault logic, when a page is ready, KVM relies on
kvm_arch_can_dequeue_async_page_present() to determine whether to deliver
a READY event to the Guest. This function test token value of struct
kvm_vcpu_pv_apf_data, which must be reset to zero by Guest kernel when a
READY event is finished by Guest. If value is zero meaning that a READY
event is done, so the KVM can deliver another.
But the kvm_arch_setup_async_pf() may produce a valid token with zero
value, which is confused with previous mention and may lead the loss of
this READY event.
Usually the kernel provides fixup routines to emulate the fldd and fstd
floating-point instructions if they load or store 8-byte from/to a not
natuarally aligned memory location.
On a 32-bit kernel I noticed that those unaligned handlers didn't worked and
instead the application got a SEGV.
While checking the code I found two problems:
First, the OPCODE_FLDD_L and OPCODE_FSTD_L cases were ifdef'ed out by the
CONFIG_PA20 option, and as such those weren't built on a pure 32-bit kernel.
This is now fixed by moving the CONFIG_PA20 #ifdef to prevent the compilation
of OPCODE_LDD_L and OPCODE_FSTD_L only, and handling the fldd and fstd
instructions.
The second problem are two bugs in the 32-bit inline assembly code, where the
wrong registers where used. The calculation of the natural alignment used %2
(vall) instead of %3 (ior), and the first word was stored back to address %1
(valh) instead of %3 (ior).
vhost_vsock_stop() calls vhost_dev_check_owner() to check the device
ownership. It expects current->mm to be valid.
vhost_vsock_stop() is also called by vhost_vsock_dev_release() when
the user has not done close(), so when we are in do_exit(). In this
case current->mm is invalid and we're releasing the device, so we
should clean it anyway.
Let's check the owner only when vhost_vsock_stop() is called
by an ioctl.
When invoked from release we can not fail so we don't check return
code of vhost_vsock_stop(). We need to stop vsock even if it's not
the owner.
Fixes: 433fc58e6bf2 ("VSOCK: Introduce vhost_vsock.ko") Cc: stable@vger.kernel.org Reported-by: syzbot+1e3ea63db39f2b4440e0@syzkaller.appspotmail.com Reported-and-tested-by: syzbot+3140b17cb44a7b174008@syzkaller.appspotmail.com Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mmc0 clock gate bit was mistakenly assigned to "i2s" clock.
You can find that the same bit is assigned to "mmc0" too.
It leads to mmc0 hang for a long time after any sound activity
also it prevented PM_SLEEP to work properly.
I guess it was introduced by copy-paste from jz4740 driver
where it is really controls I2S clock gate.
The corrupted leaf of device tree has an inode item. The leaf passed
checksum and others checks in validate_extent_buffer until check_leaf_item().
Because of the key type BTRFS_INODE_ITEM, check_inode_item() is called even we
are in the device tree. Since the
item offset + sizeof(struct btrfs_inode_item) > eb->len, out-of-bounds access
is triggered.
The item end vs leaf boundary check has been done before
check_leaf_item(), so fix it by checking item size in check_inode_item()
before access of the inode item in extent buffer.
Other check functions except check_dev_item() in check_leaf_item()
have their item size checks.
The commit for check_dev_item() is followed.
No regression observed during running fstests.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=215299 CC: stable@vger.kernel.org # 5.10+ CC: Wenqing Liu <wenqingliu0120@gmail.com> Signed-off-by: Su Yue <l@damenly.su> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As previously discussed(https://lkml.org/lkml/2022/1/20/51),
cpuset_attach() is affected with similar cpu hotplug race,
as follow scenario:
cpuset_attach() cpu hotplug
--------------------------- ----------------------
down_write(cpuset_rwsem)
guarantee_online_cpus() // (load cpus_attach)
sched_cpu_deactivate
set_cpu_active()
// will change cpu_active_mask
set_cpus_allowed_ptr(cpus_attach)
__set_cpus_allowed_ptr_locked()
// (if the intersection of cpus_attach and
cpu_active_mask is empty, will return -EINVAL)
up_write(cpuset_rwsem)
To avoid races such as described above, protect cpuset_attach() call
with cpu_hotplug_lock.
Fixes: be367d099270 ("cgroups: let ss->can_attach and ss->attach do whole threadgroups at a time") Cc: stable@vger.kernel.org # v2.6.32+ Reported-by: Zhao Gongyi <zhaogongyi@huawei.com> Signed-off-by: Zhang Qiao <zhangqiao22@huawei.com> Acked-by: Waiman Long <longman@redhat.com> Reviewed-by: Michal Koutný <mkoutny@suse.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A kernel exception was hit when trying to dump /proc/lockdep_chains after
lockdep report "BUG: MAX_LOCKDEP_CHAIN_HLOCKS too low!":
Unable to handle kernel paging request at virtual address 00054005450e05c3
... 00054005450e05c3] address between user and kernel address ranges
...
pc : [0xffffffece769b3a8] string+0x50/0x10c
lr : [0xffffffece769ac88] vsnprintf+0x468/0x69c
...
Call trace:
string+0x50/0x10c
vsnprintf+0x468/0x69c
seq_printf+0x8c/0xd8
print_name+0x64/0xf4
lc_show+0xb8/0x128
seq_read_iter+0x3cc/0x5fc
proc_reg_read_iter+0xdc/0x1d4
The cause of the problem is the function lock_chain_get_class() will
shift lock_classes index by 1, but the index don't need to be shifted
anymore since commit 01bb6f0af992 ("locking/lockdep: Change the range
of class_idx in held_lock struct") already change the index to start
from 0.
The lock_classes[-1] located at chain_hlocks array. When printing
lock_classes[-1] after the chain_hlocks entries are modified, the
exception happened.
The output of lockdep_chains are incorrect due to this problem too.
Fixes: f611e8cf98ec ("lockdep: Take read/write status in consideration when generate chainkey") Signed-off-by: Cheng Jui Wang <cheng-jui.wang@mediatek.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Boqun Feng <boqun.feng@gmail.com> Link: https://lore.kernel.org/r/20220210105011.21712-1-cheng-jui.wang@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c61837 ("i2c: brcmstb: Adding support for CM and DSL SoCs") Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One way to solve this problem is to move the fd_install() call out of
the sighand->siglock critical section.
Before commit 6fd2fe494b17 ("copy_process(): don't use ksys_close()
on cleanups"), the pidfd installation was done without holding both
the task_list lock and the sighand->siglock. Obviously, holding these
two locks are not really needed to protect the fd_install() call.
So move the fd_install() call down to after the releases of both locks.
Link: https://lore.kernel.org/r/20220208163912.1084752-1-longman@redhat.com Fixes: 6fd2fe494b17 ("copy_process(): don't use ksys_close() on cleanups") Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Waiman Long <longman@redhat.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a minor chance for a race, if a pointer to an i2c-bus subnode
is stored and then reused after releasing its reference, and it would
be sufficient to get one more reference under a loop over children
subnodes.
Fixes: e517526195de ("i2c: Add Qualcomm CCI I2C driver") Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Reviewed-by: Robert Foss <robert.foss@linaro.org> Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because of the possible failure of the dma_supported(), the
dma_set_mask_and_coherent() may return error num.
Therefore, it should be better to check it and return the error if
fails.
Do alignment logic properly and use the "ptr" local variable for
calculating the remainder of the alignment.
This became an issue because struct edac_mc_layer has a size that is not
zero modulo eight, and the next offset that was prepared for the private
data was unaligned, causing an alignment exception.
The patch in Fixes: which broke this actually wanted to "what we
actually care about is the alignment of the actual pointer that's about
to be returned." But it didn't check that alignment.
When connected point to point, the driver does not know the FC4's supported
by the other end. In Fabrics, it can query the nameserver. Thus the driver
must send PRLIs for the FC4s it supports and enable support based on the
acc(ept) or rej(ect) of the respective FC4 PRLI. Currently the driver
supports SCSI and NVMe PRLIs.
Unfortunately, although the behavior is per standard, many devices have
come to expect only SCSI PRLIs. In this particular example, the NVMe PRLI
is properly RJT'd but the target decided that it must LOGO after seeing the
unexpected NVMe PRLI. The LOGO causes the sequence to restart and login is
now in an infinite failure loop.
Fix the problem by having the driver, on a pt2pt link, remember NVMe PRLI
accept or reject status across logout as long as the link stays "up". When
retrying login, if the prior NVMe PRLI was rejected, it will not be sent on
the next login.
Link: https://lore.kernel.org/r/20220212163120.15385-1-jsmart2021@gmail.com Cc: <stable@vger.kernel.org> # v5.4+ Reviewed-by: Ewan D. Milne <emilne@redhat.com> Signed-off-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the KCONFIG_AUTOCONFIG is specified (e.g. export \
KCONFIG_AUTOCONFIG=output/config/auto.conf), the directory of
include/config/ will not be created, so kconfig can't create deps
files in it and auto.conf can't be generated.
Single page and coherent memory blocks can use different DMA masks
when the macb accesses physical memory directly. The kernel is clever
enough to allocate pages that fit into the requested address width.
When using the ARM SMMU, the DMA mask must be the same for single
pages and big coherent memory blocks. Otherwise the translation
tables turn into one big mess.
[ 74.959909] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 74.959989] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
[ 75.173939] macb ff0e0000.ethernet eth0: DMA bus error: HRESP not OK
[ 75.173955] arm-smmu fd800000.smmu: Unhandled context fault: fsr=0x402, iova=0x3165687460, fsynr=0x20001, cbfrsynra=0x877, cb=1
Since using the same DMA mask does not hurt direct 1:1 physical
memory mappings, this commit always aligns DMA and coherent masks.
Signed-off-by: Marc St-Amand <mstamand@ciena.com> Signed-off-by: Harini Katakam <harini.katakam@xilinx.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Tested-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Dell DW5829e same as DW5821e except the CAT level.
DW5821e supports CAT16 but DW5829e supports CAT9.
Also, DW5829e includes normal and eSIM type.
Please see below test evidence:
The kernel parameter "tp_printk_stop_on_boot" starts with "tp_printk" which is
the same as another kernel parameter "tp_printk". If "tp_printk" setup is
called before the "tp_printk_stop_on_boot", it will override the latter
and keep it from being set.
This is similar to other kernel parameter issues, such as:
Commit 745a600cf1a6 ("um: console: Ignore console= option")
or init/do_mounts.c:45 (setup function of "ro" kernel param)
Fix it by checking for a "_" right after the "tp_printk" and if that
exists do not process the parameter.
Link: https://lkml.kernel.org/r/20220208195421.969326-1-jsyoo5b@gmail.com Signed-off-by: JaeSang Yoo <jsyoo5b@gmail.com>
[ Fixed up change log and added space after if condition ] Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver returns an error when devm_phy_optional_get() fails leaving
the previously enabled clock turned on. Change order and enable the
clock only after the phy has been acquired.
If there are failures then we must not leave the non-NULL pointers with
the error value, otherwise `rpcrdma_ep_destroy` gets confused and tries
free them, resulting in an Oops.
Signed-off-by: Dan Aloni <dan.aloni@vastdata.com> Acked-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a checking code when it gets -EPROBE_DEFER while getting a clock
resource. In this case, it doesn't need to print out an error message
because the probing will be re-visited.
This device is a CF card, or possibly an SSD in CF form factor.
It supports NCQ and high speed DMA.
While it also advertises TRIM support, I/O errors are reported
when the discard mount option fstrim is used. TRIM also fails
when disabling NCQ and not just as an NCQ command.
TRIM must be disabled for this device.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log