The maximum message size that can be send is bigger than
the maximum site that skb_page_frag_refill can allocate.
So it is possible to write beyond the allocated buffer.
Fix this by doing a fallback to COW in that case.
v2:
Avoid get get_order() costs as suggested by Linus Torvalds.
According to Documentation/driver-api/usb/URB.rst when a device
is unplugged usb_submit_urb() returns -ENODEV.
This error code propagates all the way up to usbnet_read_cmd() and
usbnet_write_cmd() calls inside the smsc95xx.c driver during
Ethernet cable unplug, unbind or reboot.
This causes the following errors to be shown on reboot, for example:
ci_hdrc ci_hdrc.1: remove, state 1
usb usb2: USB disconnect, device number 1
usb 2-1: USB disconnect, device number 2
usb 2-1.1: USB disconnect, device number 3
smsc95xx 2-1.1:1.0 eth1: unregister 'smsc95xx' usb-ci_hdrc.1-1.1, smsc95xx USB 2.0 Ethernet
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: hardware isn't capable of remote wakeup
usb 2-1.4: USB disconnect, device number 4
ci_hdrc ci_hdrc.1: USB bus 2 deregistered
ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
imx2-wdt 30280000.watchdog: Device shutdown: Expect reboot!
reboot: Restarting system
Ignore the -ENODEV errors inside __smsc95xx_mdio_read() and
__smsc95xx_phy_wait_not_busy() and do not print error messages
when -ENODEV is returned.
Fixes: a049a30fc27c ("net: usb: Correct PHY handling of smsc95xx") Signed-off-by: Fabio Estevam <festevam@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On boards with LAN9514 and no preconfigured MAC address we don't get an
ip address from DHCP after commit a049a30fc27c ("net: usb: Correct PHY handling
of smsc95xx") anymore. Adding an explicit reset before starting the phy
fixes the issue.
From: Gabriel Hojda <ghojda@yo2urs.ro> Fixes: a049a30fc27c ("net: usb: Correct PHY handling of smsc95xx") Signed-off-by: Gabriel Hojda <ghojda@yo2urs.ro> Signed-off-by: Markus Reichl <m.reichl@fivetechno.de> Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver should not be connecting and disconnecting the PHY when the
device is opened and closed, it should be stopping and starting the PHY. The
phy should be connected as part of binding and disconnected during
unbinding.
As this results in the PHY not being reset during open, link speed, etc.
settings set prior to the link coming up are now not being lost.
It is necessary for phy_stop() to only be called when the phydev still
exists (resolving the above stack trace). When unbinding, ".unbind" will be
called prior to ".stop", with phy_disconnect() already having called
phy_stop() before the phydev becomes inaccessible.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com> Cc: Steve Glendinning <steve.glendinning@shawell.net> Cc: UNGLinuxDriver@microchip.com Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: stable@kernel.org # v5.15 Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Fabio Estevam <festevam@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this patch, the symbol end address fixup to be called, needed two
conditions being met:
if (prev->end == prev->start && prev->end != curr->start)
Where
"prev->end == prev->start" means that prev is zero-long
(and thus needs a fixup)
and
"prev->end != curr->start" means that fixup hasn't been applied yet
However, this logic is incorrect in the following situation:
In this case, prev->start == prev->end == curr->start == curr->end,
thus the condition above thinks that "we need a fixup due to zero
length of prev symbol, but it has been probably done, since the
prev->end == curr->start", which is wrong.
After the patch, the execution path proceeds to arch__symbols__fixup_end
function which fixes up the size of prev symbol by adding page_size to
its end offset.
Fixes: 3b01a413c196c910 ("perf symbols: Improve kallsyms symbol end addr calculation") Signed-off-by: Michael Petlan <mpetlan@redhat.com> Cc: Athira Jajeev <atrajeev@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Kajol Jain <kjain@linux.ibm.com> Cc: Madhavan Srinivasan <maddy@linux.ibm.com> Link: http://lore.kernel.org/lkml/20220317135536.805-1-mpetlan@redhat.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. There was a check for the number of endpoints, but not
for the type of endpoint.
Fix it by replacing old desc.bNumEndpoints check with
usb_find_common_endpoints() helper for finding endpoints
Fail log:
usb 5-1: BOGUS urb xfer, pipe 1 != type 3
WARNING: CPU: 2 PID: 48 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
Modules linked in:
CPU: 2 PID: 48 Comm: kworker/2:2 Not tainted 5.17.0-rc6-syzkaller-00226-g07ebd38a0da2 #0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
Workqueue: usb_hub_wq hub_event
...
Call Trace:
<TASK>
aiptek_open+0xd5/0x130 drivers/input/tablet/aiptek.c:830
input_open_device+0x1bb/0x320 drivers/input/input.c:629
kbd_connect+0xfe/0x160 drivers/tty/vt/keyboard.c:1593
Fixes: 8e20cf2bce12 ("Input: aiptek - fix crash on detecting device without endpoints") Reported-and-tested-by: syzbot+75cccf2b7da87fb6f84b@syzkaller.appspotmail.com Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Link: https://lore.kernel.org/r/20220308194328.26220-1-paskripkin@gmail.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is caused by mpt3sas_base_sync_reply_irqs() using an invalid reply_q
pointer outside of the list_for_each_entry() loop. At the end of the full
list traversal the pointer is invalid.
Move the _base_process_reply_queue() call inside of the loop.
Link: https://lore.kernel.org/r/d625deae-a958-0ace-2ba3-0888dd0a415b@ddn.com Fixes: 711a923c14d9 ("scsi: mpt3sas: Postprocessing of target and LUN reset") Cc: stable@vger.kernel.org Acked-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com> Signed-off-by: Matt Lupfer <mlupfer@ddn.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the bug manifested in the driver core, the real cause was a
race with the gadget core. dev_uevent() does:
if (dev->driver)
add_uevent_var(env, "DRIVER=%s", dev->driver->name);
and between the test and the dereference of dev->driver, the gadget
core sets dev->driver to NULL.
The race wouldn't occur if the gadget core registered its devices on
a real bus, using the standard synchronization techniques of the
driver core. However, it's not necessary to make such a large change
in order to fix this bug; all we need to do is make sure that
udc->dev.driver is always NULL.
In fact, there is no reason for udc->dev.driver ever to be set to
anything, let alone to the value it currently gets: the address of the
gadget's driver. After all, a gadget driver only knows how to manage
a gadget, not how to manage a UDC.
This patch simply removes the statements in the gadget core that touch
udc->dev.driver.
The newly introduced TRAMP_VALIAS definition causes a build warning
with clang-14:
arch/arm64/include/asm/vectors.h:66:31: error: arithmetic on a null pointer treated as a cast from integer to pointer is a GNU extension [-Werror,-Wnull-pointer-arithmetic]
return (char *)TRAMP_VALIAS + SZ_2K * slot;
Change the addition to something clang does not complain about.
ACL rules can be offloaded to VCAP IS2 either through chain 0, or, since
the blamed commit, through a chain index whose number encodes a specific
PAG (Policy Action Group) and lookup number.
The chain number is translated through ocelot_chain_to_pag() into a PAG,
and through ocelot_chain_to_lookup() into a lookup number.
The problem with the blamed commit is that the above 2 functions don't
have special treatment for chain 0. So ocelot_chain_to_pag(0) returns
filter->pag = 224, which is in fact -32, but the "pag" field is an u8.
So we end up programming the hardware with VCAP IS2 entries having a PAG
of 224. But the way in which the PAG works is that it defines a subset
of VCAP IS2 filters which should match on a packet. The default PAG is
0, and previous VCAP IS1 rules (which we offload using 'goto') can
modify it. So basically, we are installing filters with a PAG on which
no packet will ever match. This is the hardware equivalent of adding
filters to a chain which has no 'goto' to it.
Restore the previous functionality by making ACL filters offloaded to
chain 0 go to PAG 0 and lookup number 0. The choice of PAG is clearly
correct, but the choice of lookup number isn't "as before" (which was to
leave the lookup a "don't care"). However, lookup 0 should be fine,
since even though there are ACL actions (policers) which have a
requirement to be used in a specific lookup, that lookup is 0.
Fixes: 226e9cd82a96 ("net: mscc: ocelot: only install TCAM entries into a specific lookup and PAG") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220316192117.2568261-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The RXCHK block will return a partial checksum of 0 if it encounters
a problem while receiving a packet. Since a 1's complement sum can
only produce this result if no bits are set in the received data
stream it is fair to treat it as an invalid partial checksum and
not pass it up the stack.
Fixes: 810155397890 ("net: bcmgenet: use CHECKSUM_COMPLETE for NETIF_F_RXCSUM") Signed-off-by: Doug Berger <opendmb@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220317012812.1313196-1-opendmb@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit b7a49f73059f ("bnx2x: Utilize firmware 7.13.21.0")
added request_firmware() logic in probe() which caused
load failure when firmware file is not present in initrd (below),
as access to firmware file is not feasible during probe.
Direct firmware load for bnx2x/bnx2x-e2-7.13.15.0.fw failed with error -2
Direct firmware load for bnx2x/bnx2x-e2-7.13.21.0.fw failed with error -2
This patch fixes this issue by -
1. Removing request_firmware() logic from the probe()
such that .ndo_open() handle it as it used to handle
it earlier
2. Given request_firmware() is removed from probe(), so
driver has to relax FW version comparisons a bit against
the already loaded FW version (by some other PFs of same
adapter) to allow different compatible/close enough FWs with which
multiple PFs may run with (in different environments), as the
given PF who is in probe flow has no idea now with which firmware
file version it is going to initialize the device in ndo_open()
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 6d4e5c570c2d ("net: dsa: get port type at parse time") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220316082602.10785-1-linmq006@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If display timings were read from the devicetree using
of_get_display_timing() and pixelclk-active is defined
there, the flag DISPLAY_FLAGS_SYNC_POSEDGE/NEGEDGE is
automatically generated. Through the function
drm_bus_flags_from_videomode() e.g. called in the
panel-simple driver this flag got into the bus flags,
but then in imx_pd_bridge_atomic_check() the bus flag
check failed and will not initialize the display. The
original commit fe141cedc433 does not explain why this
check was introduced. So remove the bus flags check,
because it stops the initialization of the display with
valid bus flags.
Fixes: fe141cedc433 ("drm/imx: pd: Use bus format/flags provided by the bridge when available") Signed-off-by: Christoph Niedermaier <cniedermaier@dh-electronics.com> Cc: Marek Vasut <marex@denx.de> Cc: Boris Brezillon <boris.brezillon@collabora.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Shawn Guo <shawnguo@kernel.org> Cc: Sascha Hauer <s.hauer@pengutronix.de> Cc: Pengutronix Kernel Team <kernel@pengutronix.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: NXP Linux Team <linux-imx@nxp.com> Cc: linux-arm-kernel@lists.infradead.org
To: dri-devel@lists.freedesktop.org Tested-by: Max Krummenacher <max.krummenacher@toradex.com> Acked-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Marek Vasut <marex@denx.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220201113643.4638-1-cniedermaier@dh-electronics.com Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As the potential failure of the kvmalloc_array(),
it should be better to check and restore the 'data'
if fails in order to avoid the dereference of the
NULL pointer.
syzbot found that when an AF_PACKET socket is using PACKET_COPY_THRESH
and mmap operations, tpacket_rcv() is queueing skbs with
garbage in skb->cb[], triggering a too big copy [1]
Presumably, users of af_packet using mmap() already gets correct
metadata from the mapped buffer, we can simply make sure
to clear 12 bytes that might be copied to user space later.
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: stack-out-of-bounds in packet_recvmsg+0x56c/0x1150 net/packet/af_packet.c:3489
Write of size 165 at addr ffffc9000385fb78 by task syz-executor233/3631
This bug resulted in only the current mode being resumed and suspended when
the PHY supported both fiber and copper modes and when the PHY only supported
copper mode the fiber mode would incorrectly be attempted to be resumed and
suspended.
Fixes: 3758be3dc162 ("Marvell phy: add functions to suspend and resume both interfaces: fiber and copper links.") Signed-off-by: Kurt Cancemi <kurt@x64architecture.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20220312201512.326047-1-kurt@x64architecture.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 5f9c55c8066b ("ipv6: check return value of ipv6_skip_exthdr")
introduced an incorrect check, which leads to all ESP packets over
either TCPv6 or UDPv6 encapsulation being dropped. In this particular
case, offset is negative, since skb->data points to the ESP header in
the following chain of headers, while skb->network_header points to
the IPv6 header:
IPv6 | ext | ... | ext | UDP | ESP | ...
That doesn't seem to be a problem, especially considering that if we
reach esp6_input_done2, we're guaranteed to have a full set of headers
available (otherwise the packet would have been dropped earlier in the
stack). However, it means that the return value will (intentionally)
be negative. We can make the test more specific, as the expected
return value of ipv6_skip_exthdr will be the (negated) size of either
a UDP header, or a TCP header with possible options.
In the future, we should probably either make ipv6_skip_exthdr
explicitly accept negative offsets (and adjust its return value for
error cases), or make ipv6_skip_exthdr only take non-negative
offsets (and audit all callers).
Fixes: 5f9c55c8066b ("ipv6: check return value of ipv6_skip_exthdr") Reported-by: Xiumei Mu <xmu@redhat.com> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When iterating over sockets using vsock_for_each_connected_socket, make
sure that a transport filters out sockets that don't belong to the
transport.
There actually was an issue caused by this; in a nested VM
configuration, destroying the nested VM (which often involves the
closing of /dev/vhost-vsock if there was h2g connections to the nested
VM) kills not only the h2g connections, but also all existing g2h
connections to the (outmost) host which are totally unrelated.
Tested: Executed the following steps on Cuttlefish (Android running on a
VM) [1]: (1) Enter into an `adb shell` session - to have a g2h
connection inside the VM, (2) open and then close /dev/vhost-vsock by
`exec 3< /dev/vhost-vsock && exec 3<&-`, (3) observe that the adb
session is not reset.
When "dump_apple_properties" is used on the kernel boot command line,
it causes an Unknown parameter message and the string is added to init's
argument strings:
Unknown kernel command line parameters "dump_apple_properties
BOOT_IMAGE=/boot/bzImage-517rc6 efivar_ssdt=newcpu_ssdt", will be
passed to user space.
Run /sbin/init as init process
with arguments:
/sbin/init
dump_apple_properties
with environment:
HOME=/
TERM=linux
BOOT_IMAGE=/boot/bzImage-517rc6
efivar_ssdt=newcpu_ssdt
Similarly when "efivar_ssdt=somestring" is used, it is added to the
Unknown parameter message and to init's environment strings, polluting
them (see examples above).
Change the return value of the __setup functions to 1 to indicate
that the __setup options have been handled.
Fixes: 58c5475aba67 ("x86/efi: Retrieve and assign Apple device properties") Fixes: 475fb4e8b2f4 ("efi / ACPI: load SSTDs from EFI variables") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru Cc: Ard Biesheuvel <ardb@kernel.org> Cc: linux-efi@vger.kernel.org Cc: Lukas Wunner <lukas@wunner.de> Cc: Octavian Purdila <octavian.purdila@intel.com> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Cc: Matt Fleming <matt@codeblueprint.co.uk> Link: https://lore.kernel.org/r/20220301041851.12459-1-rdunlap@infradead.org Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reason for the livelock is that swapcache_prepare() always returns
EEXIST, indicating that SWAP_HAS_CACHE has not been cleared, so that it
cannot jump out of the loop. We suspect that the task that clears the
SWAP_HAS_CACHE flag never gets a chance to run. We try to lower the
priority of the task stuck in a livelock so that the task that clears
the SWAP_HAS_CACHE flag will run. The results show that the system
returns to normal after the priority is lowered.
In our testing, multiple real-time tasks are bound to the same core, and
the task in the livelock is the highest priority task of the core, so
the livelocked task cannot be preempted.
Although cond_resched() is used by __read_swap_cache_async, it is an
empty function in the preemptive system and cannot achieve the purpose
of releasing the CPU. A high-priority task cannot release the CPU
unless preempted by a higher-priority task. But when this task is
already the highest priority task on this core, other tasks will not be
able to be scheduled. So we think we should replace cond_resched() with
schedule_timeout_uninterruptible(1), schedule_timeout_interruptible will
call set_current_state first to set the task state, so the task will be
removed from the running queue, so as to achieve the purpose of giving
up the CPU and prevent it from running in kernel mode for too long.
(akpm: ugly hack becomes uglier. But it fixes the issue in a
backportable-to-stable fashion while we hopefully work on something
better)
Link: https://lkml.kernel.org/r/20220221111749.1928222-1-cgel.zte@gmail.com Signed-off-by: Guo Ziliang <guo.ziliang@zte.com.cn> Reported-by: Zeal Robot <zealci@zte.com.cn> Reviewed-by: Ran Xiaokai <ran.xiaokai@zte.com.cn> Reviewed-by: Jiang Xuexin <jiang.xuexin@zte.com.cn> Reviewed-by: Yang Yang <yang.yang29@zte.com.cn> Acked-by: Hugh Dickins <hughd@google.com> Cc: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: Minchan Kim <minchan@kernel.org> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Roger Quadros <rogerq@kernel.org> Cc: Ziliang Guo <guo.ziliang@zte.com.cn> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once s_root is set, genric_shutdown_super() will be called if
fill_super() fails. That means, we will call ocfs2_dismount_volume()
twice in such case, which can lead to kernel crash.
Fix this issue by initializing filecheck kobj before setting s_root.
Link: https://lkml.kernel.org/r/20220310081930.86305-1-joseph.qi@linux.alibaba.com Fixes: 5f483c4abb50 ("ocfs2: add kobject for online file check") Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Gang He <ghe@suse.com> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generate function in struct rng_alg expects that the destination
buffer is completely filled if the function returns 0. qcom_rng_read()
can run into a situation where the buffer is partially filled with
randomness and the remaining part of the buffer is zeroed since
qcom_rng_generate() doesn't check the return value. This issue can
be reproduced by running the following from libkcapi:
The generated OUTFILE will have three huge sections that contain all
zeros, and this is caused by the code where the test
'val & PRNG_STATUS_DATA_AVAIL' fails.
Let's fix this issue by ensuring that qcom_rng_read() always returns
with a full buffer if the function returns success. Let's also have
qcom_rng_generate() return the correct value.
Here's some statistics from the ent project
(https://www.fourmilab.ch/random/) that shows information about the
quality of the generated numbers:
Optimum compression would reduce the size
of this 9000000 byte file by 2 percent.
Chi square distribution for 9000000 samples is 9329962.81, and
randomly would exceed this value less than 0.01 percent of the
times.
Arithmetic mean value of data bytes is 119.3731 (127.5 = random).
Monte Carlo value for Pi is 3.197293333 (error 1.77 percent).
Serial correlation coefficient is 0.159130 (totally uncorrelated =
0.0).
Without this patch, the results of the chi-square test is 0.01%, and
the numbers are certainly not random according to ent's project page.
The results improve with this patch:
Optimum compression would reduce the size
of this 9000000 byte file by 0 percent.
Chi square distribution for 9000000 samples is 258.77, and randomly
would exceed this value 42.24 percent of the times.
Arithmetic mean value of data bytes is 127.5006 (127.5 = random).
Monte Carlo value for Pi is 3.141277333 (error 0.01 percent).
Serial correlation coefficient is 0.000468 (totally uncorrelated =
0.0).
This change was tested on a Nexus 5 phone (msm8974 SoC).
James Morse [Tue, 15 Mar 2022 13:57:20 +0000 (13:57 +0000)]
arm64: kvm: Fix copy-and-paste error in bhb templates for v5.10 stable
KVM's infrastructure for spectre mitigations in the vectors in v5.10 and
earlier is different, it uses templates which are used to build a set of
vectors at runtime.
There are two copy-and-paste errors in the templates: __spectre_bhb_loop_k24
should loop 24 times and __spectre_bhb_loop_k32 32.
Revert of revert of "io_uring: wait potential ->release() on resurrect",
which adds a helper for resurrect not racing completion reinit, as was
removed because of a strange bug with no clear root or link to the
patch.
Was improved, instead of rcu_synchronize(), just wait_for_completion()
because we're at 0 refs and it will happen very shortly. Specifically
use non-interruptible version to ignore all pending signals that may
have ended prior interruptible wait.
The error message when I build vm tests on debian10 (GLIBC 2.28):
userfaultfd.c: In function `userfaultfd_pagemap_test':
userfaultfd.c:1393:37: error: `MADV_PAGEOUT' undeclared (first use
in this function); did you mean `MADV_RANDOM'?
if (madvise(area_dst, test_pgsize, MADV_PAGEOUT))
^~~~~~~~~~~~
MADV_RANDOM
This patch includes these newer definitions from UAPI linux/mman.h, is
useful to fix tests build on systems without these definitions in glibc
sys/mman.h.
seqno could be read as a stale value outside of the lock. The lock is
already acquired to protect the modification of seqno against a possible
race condition. Place the reading of this value also inside this locking
to protect it against a possible race condition.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com> Acked-by: Martin Habets <habetsm.xilinx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The wdev channel information is updated post channel switch only for
the station mode and not for the other modes. Due to this, the P2P client
still points to the old value though it moved to the new channel
when the channel change is induced from the P2P GO.
Update the bss channel after CSA channel switch completion for P2P client
interface as well.
VRR capable property is not attached by default to the connector
It is attached only if VRR is supported.
So if the driver tries to call drm core set prop function without
it being attached that causes NULL dereference.
Cc: Jani Nikula <jani.nikula@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: dri-devel@lists.freedesktop.org Signed-off-by: Manasi Navare <manasi.d.navare@intel.com> Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220225013055.9282-1-manasi.d.navare@intel.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Some APs misbehave when TWT is used and cause our firmware to crash.
We don't know a reasonable way to detect and work around this problem
in the FW yet. To prevent these crashes, disable TWT in the driver by
stopping to advertise TWT support.
The function ioremap() in fs_init() can fail, so its return value should
be checked.
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Register the CAN device only when all the necessary initialization is
completed. This patch makes sure all the data structures and locks are
initialized before registering the CAN device.
Link: https://lore.kernel.org/all/20220221225935.12300-1-prabhakar.mahadev-lad.rj@bp.renesas.com Reported-by: Pavel Machek <pavel@denx.de> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Reviewed-by: Pavel Machek <pavel@denx.de> Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
...for each but CPU 0/boot.
Basic debug printks right before the mentioned line say:
[ 0.048170] CPU: 1, smt_mask:
So smt_mask, which is sibling mask obviously, is empty when entering
the function.
This is critical, as sched_core_cpu_starting() calculates
core-scheduling parameters only once per CPU start, and it's crucial
to have all the parameters filled in at that moment (at least it
uses cpu_smt_mask() which in fact is `&cpu_sibling_map[cpu]` on
MIPS).
A bit of debugging led me to that set_cpu_sibling_map() performing
the actual map calculation, was being invocated after
notify_cpu_start(), and exactly the latter function starts CPU HP
callback round (sched_core_cpu_starting() is basically a CPU HP
callback).
While the flow is same on ARM64 (maps after the notifier, although
before calling set_cpu_online()), x86 started calculating sibling
maps earlier than starting the CPU HP callbacks in Linux 4.14 (see
[0] for the reference). Neither me nor my brief tests couldn't find
any potential caveats in calculating the maps right after performing
delay calibration, but the WARN splat is now gone.
The very same debug prints now yield exactly what I expected from
them:
If an MFP station isn't authorized, the receiver will (or
at least should) drop the action frame since it's a robust
management frame, but if we're not authorized we haven't
installed keys yet. Refuse attempts to start a session as
they'd just time out.
There are signal integrity issues running the eMMC at 200MHz on Puma
RK3399-Q7.
Similar to the work-around found for RK3399 Gru boards, lowering the
frequency to 100MHz made the eMMC much more stable, so let's lower the
frequency to 100MHz.
It might be possible to run at 150MHz as on RK3399 Gru boards but only
100MHz was extensively tested.
xfrm_migrate cannot handle address family change of an xfrm_state.
The symptons are the xfrm_state will be migrated to a wrong address,
and sending as well as receiving packets wil be broken.
This commit fixes it by breaking the original xfrm_state_clone
method into two steps so as to update the props.family before
running xfrm_init_state. As the result, xfrm_state's inner mode,
outer mode, type and IP header length in xfrm_state_migrate can
be updated with the new address family.
Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1885354
Signed-off-by: Yan Yan <evitayan@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch enables distinguishing SAs and SPs based on if_id during
the xfrm_migrate flow. This ensures support for xfrm interfaces
throughout the SA/SP lifecycle.
When there are multiple existing SPs with the same direction,
the same xfrm_selector and different endpoint addresses,
xfrm_migrate might fail with ENODATA.
Specifically, the code path for performing xfrm_migrate is:
Stage 1: find policy to migrate with
xfrm_migrate_policy_find(sel, dir, type, net)
Stage 2: find and update state(s) with
xfrm_migrate_state_find(mp, net)
Stage 3: update endpoint address(es) of template(s) with
xfrm_policy_migrate(pol, m, num_migrate)
Currently "Stage 1" always returns the first xfrm_policy that
matches, and "Stage 3" looks for the xfrm_tmpl that matches the
old endpoint address. Thus if there are multiple xfrm_policy
with same selector, direction, type and net, "Stage 1" might
rertun a wrong xfrm_policy and "Stage 3" will fail with ENODATA
because it cannot find a xfrm_tmpl with the matching endpoint
address.
The fix is to allow userspace to pass an if_id and add if_id
to the matching rule in Stage 1 and Stage 2 since if_id is a
unique ID for xfrm_policy and xfrm_state. For compatibility,
if_id will only be checked if the attribute is set.
Tested with additions to Android's kernel unit test suite:
https://android-review.googlesource.com/c/kernel/tests/+/1668886
Signed-off-by: Yan Yan <evitayan@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
1. In non-shutdown_ack_sent states: in sctp_sf_do_5_1B_init() and
sctp_sf_do_5_2_2_dupinit():
chunk length check should be done before any checks that may cause
to send abort, as making packet for abort will access the init_tag
from init_hdr in sctp_ootb_pkt_new().
2. In shutdown_ack_sent state: in sctp_sf_do_9_2_reshutack():
The same checks as does in sctp_sf_do_5_2_2_dupinit() is needed
for sctp_sf_do_9_2_reshutack().
This reverts commit 68ac0f3810e76a853b5f7b90601a05c3048b8b54 because ID
0 was meant to be used for configuring the policy/state without
matching for a specific interface (e.g., Cilium is affected, see
https://github.com/cilium/cilium/pull/18789 and
https://github.com/cilium/cilium/pull/19019).
In watch_queue_set_filter(), there are a couple of places where we check
that the filter type value does not exceed what the type_filter bitmap
can hold. One place calculates the number of bits by:
if (tf[i].type >= sizeof(wfilter->type_filter) * 8)
which is fine, but the second does:
if (tf[i].type >= sizeof(wfilter->type_filter) * BITS_PER_LONG)
which is not. This can lead to a couple of out-of-bounds writes due to
a too-large type:
(1) __set_bit() on wfilter->type_filter
(2) Writing more elements in wfilter->filters[] than we allocated.
Fix this by just using the proper WATCH_TYPE__NR instead, which is the
number of types we actually know about.
The bug may cause an oops looking something like:
BUG: KASAN: slab-out-of-bounds in watch_queue_set_filter+0x659/0x740
Write of size 4 at addr ffff88800d2c66bc by task watch_queue_oob/611
...
Call Trace:
<TASK>
dump_stack_lvl+0x45/0x59
print_address_description.constprop.0+0x1f/0x150
...
kasan_report.cold+0x7f/0x11b
...
watch_queue_set_filter+0x659/0x740
...
__x64_sys_ioctl+0x127/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
Allocated by task 611:
kasan_save_stack+0x1e/0x40
__kasan_kmalloc+0x81/0xa0
watch_queue_set_filter+0x23a/0x740
__x64_sys_ioctl+0x127/0x190
do_syscall_64+0x43/0x90
entry_SYSCALL_64_after_hwframe+0x44/0xae
The buggy address belongs to the object at ffff88800d2c66a0
which belongs to the cache kmalloc-32 of size 32
The buggy address is located 28 bytes inside of
32-byte region [ffff88800d2c66a0, ffff88800d2c66c0)
When building for Thumb2, the vectors make use of a local label. Sadly,
the Spectre BHB code also uses a local label with the same number which
results in the Thumb2 reference pointing at the wrong place. Fix this
by changing the number used for the Spectre BHB local label.
The in-kernel ext4 resize code doesn't support filesystem with the
sparse_super2 feature. It fails with errors like this and doesn't finish
the resize:
EXT4-fs (loop0): resizing filesystem from 16640 to 7864320 blocks
EXT4-fs warning (device loop0): verify_reserved_gdb:760: reserved GDT 2 missing grp 1 (32770)
EXT4-fs warning (device loop0): ext4_resize_fs:2111: error (-22) occurred during file system resize
EXT4-fs (loop0): resized filesystem to 2097152
The userspace resize2fs tool has a check for this case: it checks if the
filesystem has sparse_super2 set and if the kernel provides
/sys/fs/ext4/features/sparse_super2. However, the former check requires
manually reading and parsing the filesystem superblock.
Detect this case in ext4_resize_begin and error out early with a clear
error message.
Since kprobe_int3_handler() is called in do_int3(), probing do_int3()
can cause a breakpoint recursion and crash the kernel. Therefore,
do_int3() should be marked as NOKPROBE_SYMBOL.
The x86 boot documentation describes the setup_indirect structures and
how they are used. Only one of the two functions in ioremap.c that needed
to be modified to be aware of the introduction of setup_indirect
functionality was updated. Adds comparable support to the other function
where it was missing.
As documented, the setup_indirect structure is nested inside
the setup_data structures in the setup_data list. The code currently
accesses the fields inside the setup_indirect structure but only
the sizeof(struct setup_data) is being memremapped. No crash
occurred but this is just due to how the area is remapped under the
covers.
Properly memremap both the setup_data and setup_indirect structures
in these cases before accessing them.
watch_queue_clear() has a comment stating that setting ->defunct to true
preventing new additions as well as preventing notifications. Whilst
the latter is true, the first bit is superfluous since at the time this
function is called, the pipe cannot be accessed to add new event
sources.
There's nothing to synchronise post_one_notification() versus
pipe_read(). Whilst posting is done under pipe->rd_wait.lock, the
reader only takes pipe->mutex which cannot bar notification posting as
that may need to be made from contexts that cannot sleep.
Fix this by setting pipe->head with a barrier in post_one_notification()
and reading pipe->head with a barrier in pipe_read().
If that's not sufficient, the rd_wait.lock will need to be taken,
possibly in a ->confirm() op so that it only applies to notifications.
The lock would, however, have to be dropped before copy_page_to_iter()
is invoked.
Currently, watch_queue_set_size() sets the number of notes available in
wqueue->nr_notes according to the number of notes allocated, but sets
the size of the bitmap to the unrounded number of notes originally asked
for.
Fix this by setting the bitmap size to the number of notes we're
actually going to make available (ie. the number allocated).
The pipe ring size must always be a power of 2 as the head and tail
pointers are masked off by AND'ing with the size of the ring - 1.
watch_queue_set_size(), however, lets you specify any number of notes
between 1 and 511. This number is passed through to pipe_resize_ring()
without checking/forcing its alignment.
Fix this by rounding the number of slots required up to the nearest
power of two. The request is meant to guarantee that at least that many
notifications can be generated before the queue is full, so rounding
down isn't an option, but, alternatively, it may be better to give an
error if we aren't allowed to allocate that much ring space.
When a pipe ring descriptor points to a notification message, the
refcount on the backing page is incremented by the generic get function,
but the release function, which marks the bitmap, doesn't drop the page
ref.
Fix this by calling generic_pipe_buf_release() at the end of
watch_queue_pipe_buf_release().
In free_pipe_info(), free the watchqueue state after clearing the pipe
ring as each pipe ring descriptor has a release function, and in the
case of a notification message, this is watch_queue_pipe_buf_release()
which tries to mark the allocation bitmap that was previously released.
Fix this by moving the put of the pipe's ref on the watch queue to after
the ring has been cleared. We still need to call watch_queue_clear()
before doing that to make sure that the pipe is disconnected from any
notification sources first.
The feature negotiation was designed in a way that
makes it possible for devices to know which config
fields will be accessed by drivers.
This is broken since commit 404123c2db79 ("virtio: allow drivers to
validate features") with fallout in at least block and net. We have a
partial work-around in commit 2f9a174f918e ("virtio: write back
F_VERSION_1 before validate") which at least lets devices find out which
format should config space have, but this is a partial fix: guests
should not access config space without acknowledging features since
otherwise we'll never be able to change the config space format.
To fix, split finalize_features from virtio_finalize_features and
call finalize_features with all feature bits before validation,
and then - if validation changed any bits - once again after.
Since virtio_finalize_features no longer writes out features
rename it to virtio_features_ok - since that is what it does:
checks that features are ok with the device.
As a side effect, this also reduces the amount of hypervisor accesses -
we now only acknowledge features once unless we are clearing any
features when validating (which is uncommon).
IRC I think that this was more or less always the intent in the spec but
unfortunately the way the spec is worded does not say this explicitly, I
plan to address this at the spec level, too.
Acked-by: Jason Wang <jasowang@redhat.com> Cc: stable@vger.kernel.org Fixes: 404123c2db79 ("virtio: allow drivers to validate features") Fixes: 2f9a174f918e ("virtio: write back F_VERSION_1 before validate") Cc: "Halil Pasic" <pasic@linux.ibm.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
virtio_finalize_features is only used internally within virtio.
No reason to export it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Legacy and old PCI I/O based cards do not support 32-bit I/O addressing.
Since commit 64f160e19e92 ("PCI: aardvark: Configure PCIe resources from
'ranges' DT property") kernel can set different PCIe address on CPU and
different on the bus for the one A37xx address mapping without any firmware
support in case the bus address does not conflict with other A37xx mapping.
So remap I/O space to the bus address 0x0 to enable support for old legacy
I/O port based cards which have hardcoded I/O ports in low address space.
Note that DDR on A37xx is mapped to bus address 0x0. And mapping of I/O
space can be set to address 0x0 too because MEM space and I/O space are
separate and so do not conflict.
Remapping IO space on Turris Mox to different address is not possible to
due bootloader bug.
RISC-V can do PC-relative jumps with a 32bit range using the following
two instructions:
auipc t0, imm20 ; t0 = PC + imm20 * 2^12
jalr ra, t0, imm12 ; ra = PC + 4, PC = t0 + imm12
Crucially both the 20bit immediate imm20 and the 12bit immediate imm12
are treated as two's-complement signed values. For this reason the
immediates are usually calculated like this:
..where offset is the signed offset from the auipc instruction. When
the 11th bit of offset is 0 the addition of 0x800 doesn't change the top
20 bits and imm12 considered positive. When the 11th bit is 1 the carry
of the addition by 0x800 means imm20 is one higher, but since imm12 is
then considered negative the two's complement representation means it
all cancels out nicely.
However, this addition by 0x800 (2^11) means an offset greater than or
equal to 2^31 - 2^11 would overflow so imm20 is considered negative and
result in a backwards jump. Similarly the lower range of offset is also
moved down by 2^11 and hence the true 32bit range is
Currently meson_mmc_post_req() is called in meson_mmc_request() right
after meson_mmc_start_cmd(). This could lead to DMA unmapping before the request
is actually finished.
To fix, don't call meson_mmc_post_req() until meson_mmc_request_done().
Signed-off-by: Rong Chen <rong.chen@amlogic.com> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Fixes: 79ed05e329c3 ("mmc: meson-gx: add support for descriptor chain mode") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20220216124239.4007667-1-rong.chen@amlogic.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is an oddity in the way the RSR register flags propagate to the
ISR register (and the actual interrupt output) on this hardware: it
appears that RSR register bits only result in ISR being asserted if the
interrupt was actually enabled at the time, so enabling interrupts with
RSR bits already set doesn't trigger an interrupt to be raised. There
was already a partial fix for this race in the macb_poll function where
it checked for RSR bits being set and re-triggered NAPI receive.
However, there was a still a race window between checking RSR and
actually enabling interrupts, where a lost wakeup could happen. It's
necessary to check again after enabling interrupts to see if RSR was set
just prior to the interrupt being enabled, and re-trigger receive in that
case.
This issue was noticed in a point-to-point UDP request-response protocol
which periodically saw timeouts or abnormally high response times due to
received packets not being processed in a timely fashion. In many
applications, more packets arriving, including TCP retransmissions, would
cause the original packet to be processed, thus masking the issue.
Fixes: 02f7a34f34e3 ("net: macb: Re-enable RX interrupt only when RX is done") Cc: stable@vger.kernel.org Co-developed-by: Scott McNutt <scott.mcnutt@siriusxm.com> Signed-off-by: Scott McNutt <scott.mcnutt@siriusxm.com> Signed-off-by: Robert Hancock <robert.hancock@calian.com> Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 54659ca026e5 ("staging: rtl8723bs: remove possible deadlock when
disconnect (v2)") split the locking of pxmitpriv->lock vs sleep_q/lock
into 2 locks in attempt to fix a lockdep reported issue with the locking
order of the sta_hash_lock vs pxmitpriv->lock.
But in the end this turned out to not fully solve the sta_hash_lock issue
so commit a7ac783c338b ("staging: rtl8723bs: remove a second possible
deadlock") was added to fix this in another way.
The original fix was kept as it was still seen as a good thing to have,
but now it turns out that it creates a deadlock in access-point mode:
[Feb20 23:47] ======================================================
[ +0.074085] WARNING: possible circular locking dependency detected
[ +0.074077] 5.16.0-1-amd64 #1 Tainted: G C E
[ +0.064710] ------------------------------------------------------
[ +0.074075] ksoftirqd/3/29 is trying to acquire lock:
[ +0.060542] ffffb8b30062ab00 (&pxmitpriv->lock){+.-.}-{2:2}, at: rtw_xmit_classifier+0x8a/0x140 [r8723bs]
[ +0.114921]
but task is already holding lock:
[ +0.069908] ffffb8b3007ab704 (&psta->sleep_q.lock){+.-.}-{2:2}, at: wakeup_sta_to_xmit+0x3b/0x300 [r8723bs]
[ +0.116976]
which lock already depends on the new lock.
[ +0.070950] 1 lock held by ksoftirqd/3/29:
[ +0.049082] #0: ffffb8b3007ab704 (&psta->sleep_q.lock){+.-.}-{2:2}, at: wakeup_sta_to_xmit+0x3b/0x300 [r8723bs]
Analysis shows that in hindsight the splitting of the lock was not
a good idea, so revert this to fix the access-point mode deadlock.
Note this is a straight-forward revert done with git revert, the commented
out "/* spin_lock_bh(&psta_bmc->sleep_q.lock); */" lines were part of the
code before the reverted changes.
In FOPEN_DIRECT_IO mode, fuse_file_write_iter() calls
fuse_direct_write_iter(), which normally calls fuse_direct_io(), which then
imports the write buffer with fuse_get_user_pages(), which uses
iov_iter_get_pages() to grab references to userspace pages instead of
actually copying memory.
On the filesystem device side, these pages can then either be read to
userspace (via fuse_dev_read()), or splice()d over into a pipe using
fuse_dev_splice_read() as pipe buffers with &nosteal_pipe_buf_ops.
This is wrong because after fuse_dev_do_read() unlocks the FUSE request,
the userspace filesystem can mark the request as completed, causing write()
to return. At that point, the userspace filesystem should no longer have
access to the pipe buffer.
Fix by copying pages coming from the user address space to new pipe
buffers.
When CONFIG_GENERIC_CPU_VULNERABILITIES is not set, references
to spectre_v2_update_state() cause a build error, so provide an
empty stub for that function when the Kconfig option is not set.
Fixes this build error:
arm-linux-gnueabi-ld: arch/arm/mm/proc-v7-bugs.o: in function `cpu_v7_bugs_init':
proc-v7-bugs.c:(.text+0x52): undefined reference to `spectre_v2_update_state'
arm-linux-gnueabi-ld: proc-v7-bugs.c:(.text+0x82): undefined reference to `spectre_v2_update_state'
Fixes: b9baf5c8c5c3 ("ARM: Spectre-BHB workaround") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Russell King <rmk+kernel@armlinux.org.uk> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: linux-arm-kernel@lists.infradead.org Cc: patches@armlinux.org.uk Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running the memfd script ./run_hugetlbfs_test.sh will often end in error
as follows:
memfd-hugetlb: CREATE
memfd-hugetlb: BASIC
memfd-hugetlb: SEAL-WRITE
memfd-hugetlb: SEAL-FUTURE-WRITE
memfd-hugetlb: SEAL-SHRINK
fallocate(ALLOC) failed: No space left on device
./run_hugetlbfs_test.sh: line 60: 166855 Aborted (core dumped) ./memfd_test hugetlbfs
opening: ./mnt/memfd
fuse: DONE
If no hugetlb pages have been preallocated, run_hugetlbfs_test.sh will
allocate 'just enough' pages to run the test. In the SEAL-FUTURE-WRITE
test the mfd_fail_write routine maps the file, but does not unmap. As a
result, two hugetlb pages remain reserved for the mapping. When the
fallocate call in the SEAL-SHRINK test attempts allocate all hugetlb
pages, it is short by the two reserved pages.
Fix by making sure to unmap in mfd_fail_write.
Link: https://lkml.kernel.org/r/20220219004340.56478-1-mike.kravetz@oracle.com Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Joel Fernandes <joel@joelfernandes.org> Cc: Shuah Khan <shuah@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
valid_lft, prefered_lft and tstamp are always accessed under the lock
"lock" in other places. Reading these without taking the lock may result
in inconsistencies regarding the calculation of the valid and preferred
variables since decisions are taken on these fields for those variables.
The reasoning in the commit was wrong - the code expected to setup the
watch even if 'hotplug-status' didn't exist. In fact, it relied on the
watch being fired the first time - to check if maybe 'hotplug-status' is
already set to 'connected'. Not registering a watch for non-existing
path (which is the case if hotplug script hasn't been executed yet),
made the backend not waiting for the hotplug script to execute. This in
turns, made the netfront think the interface is fully operational, while
in fact it was not (the vif interface on xen-netback side might not be
configured yet).
This was a workaround for 'hotplug-status' erroneously being removed.
But since that is reverted now, the workaround is not necessary either.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
Signed-off-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Reviewed-by: Paul Durrant <paul@xen.org> Reviewed-by: Michael Brown <mbrown@fensystems.co.uk> Link: https://lore.kernel.org/r/20220222001817.2264967-2-marmarek@invisiblethingslab.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 'hotplug-status' node should not be removed as long as the vif
device remains configured. Otherwise the xen-netback would wait for
re-running the network script even if it was already called (in case of
the frontent re-connecting). But also, it _should_ be removed when the
vif device is destroyed (for example when unbinding the driver) -
otherwise hotplug script would not configure the device whenever it
re-appear.
Moving removal of the 'hotplug-status' node was a workaround for nothing
calling network script after xen-netback module is reloaded. But when
vif interface is re-created (on xen-netback unbind/bind for example),
the script should be called, regardless of who does that - currently
this case is not handled by the toolstack, and requires manual
script call. Keeping hotplug-status=connected to skip the call is wrong
and leads to not configured interface.
More discussion at
https://lore.kernel.org/xen-devel/afedd7cb-a291-e773-8b0d-4db9b291fa98@ipxe.org/T/#u
We are racing the registering of .to_irq when probing the
i2c driver. This results in random failure of touchscreen
devices.
Following explains the race condition better.
[gpio driver] gpio driver registers gpio chip
[gpio consumer] gpio is acquired
[gpio consumer] gpiod_to_irq() fails with -ENXIO
[gpio driver] gpio driver registers irqchip
gpiod_to_irq works at this point, but -ENXIO is fatal
We could see the following errors in dmesg logs when gc->to_irq is NULL
[2.101857] i2c_hid i2c-FTS3528:00: HID over i2c has not been provided an Int IRQ
[2.101953] i2c_hid: probe of i2c-FTS3528:00 failed with error -22
To avoid this situation, defer probing until to_irq is registered.
Returning -EPROBE_DEFER would be the first step towards avoiding
the failure of devices due to the race in registration of .to_irq.
Final solution to this issue would be to avoid using gc irq members
until they are fully initialized.
This issue has been reported many times in past and people have been
using workarounds like changing the pinctrl_amd to built-in instead
of loading it as a module or by adding a softdep for pinctrl_amd into
the config file.
Almost all fault/warning bits in pmbus status registers remain set even
after fault/warning condition are removed. As per pmbus specification
these faults must be cleared by user.
Modify hwmon behavior to clear fault/warning bit after fetching data if
fault/warning bit was set. This allows to get fresh data in next read.
Add a test that validates that timer value is not overwritten when doing
a copy_map_value call in the kernel. Without the prior fix, this test
triggers a crash.
Some of the bcmgenet platforms don't correctly support WOL, yet
ethtool returns:
"Supports Wake-on: gsf"
which is false.
Ideally if there isn't a wol_irq, or there is something else that
keeps the device from being able to wakeup it should display:
"Supports Wake-on: d"
This patch checks whether the device can wakup, before using the
hard-coded supported flags. This corrects the ethtool reporting, as
well as the WOL configuration because ethtool verifies that the mode
is supported before attempting it.
Fixes: c51de7f3976b ("net: bcmgenet: add Wake-on-LAN support code") Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Tested-by: Peter Robinson <pbrobinson@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220310045535.224450-1-jeremy.linton@arm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The of_find_compatible_node() function returns a node pointer with
refcount incremented, We should use of_node_put() on it when done
Add the missing of_node_put() to release the refcount.
Fixes: 7349a74ea75c ("net: ethernet: gianfar_ethtool: get phc index through drvdata") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20220310015313.14938-1-linmq006@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This works around an issue with the hardware where both OE and
DAT are exposed in the same register. If both are updated
simultaneously, the harware makes no guarantees that OE or DAT
will actually change in any given order and may result in a
glitch of a few ns on a GPIO pin when changing direction and value
in a single write.
Setting direction to input now only affects OE bit. Setting
direction to output updates DAT first, then OE.
The cleanup() function takes care of killing processes launched by the
test functions. It relies on variables like ${tcpdump_pids} to get the
relevant PIDs. But tests are run in their own subshell, so updated
*_pids values are invisible to other shells. Therefore cleanup() never
sees any process to kill:
Fix this by running cleanup() in the context of the test subshell.
Now that each test cleans the environment after completion, there's no
need for calling cleanup() again when the next test starts. So let's
drop it from the setup() function. This is okay because cleanup() is
also called when pmtu.sh starts, so even the first test starts in a
clean environment.
Also, use tcpdump's immediate mode. Otherwise it might not have time to
process buffered packets, resulting in missing packets or even empty
pcap files for short tests.
Note: PAUSE_ON_FAIL is still evaluated before cleanup(), so one can
still inspect the test environment upon failure when using -p.
Syzbot reported UAF in port100_send_complete(). The root case is in
missing usb_kill_urb() calls on error handling path of ->probe function.
port100_send_complete() accesses devm allocated memory which will be
freed on probe failure. We should kill this urbs before returning an
error from probe function to prevent reported use-after-free
Fail log:
BUG: KASAN: use-after-free in port100_send_complete+0x16e/0x1a0 drivers/nfc/port100.c:935
Read of size 1 at addr ffff88801bb59540 by task ksoftirqd/2/26
...
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x303 mm/kasan/report.c:255
__kasan_report mm/kasan/report.c:442 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:459
port100_send_complete+0x16e/0x1a0 drivers/nfc/port100.c:935
__usb_hcd_giveback_urb+0x2b0/0x5c0 drivers/usb/core/hcd.c:1670
There could be multiple multipath entries but changing the port affinity
for each one doesn't make much sense and there should be a default one.
So only track the entry with lowest priority value.
The commit doesn't affect existing users with a single entry.
Fixes: 544fe7c2e654 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events") Signed-off-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix a refcount use after free warning due to a race on command entry.
Such race occurs when one of the commands releases its last refcount and
frees its index and entry while another process running command flush
flow takes refcount to this command entry. The process which handles
commands flush may see this command as needed to be flushed if the other
process released its refcount but didn't release the index yet. Fix it
by adding the needed spin lock.
projects / linux-stable / log