When we upgraded our kernel, we started seeing some page corruption like
the following consistently:
BUG: Bad page state in process ganesha.nfsd pfn:1304ca
page:0000000022261c55 refcount:0 mapcount:-128 mapping:0000000000000000 index:0x0 pfn:0x1304ca
flags: 0x17ffffc0000000()
raw: 0017ffffc0000000ffff8a513ffd4c98ffffeee24b35ec080000000000000000
raw: 0000000000000000000000000000000100000000ffffff7f0000000000000000
page dumped because: nonzero mapcount
CPU: 0 PID: 15567 Comm: ganesha.nfsd Kdump: loaded Tainted: P B O 5.10.158-1.nutanix.20221209.el7.x86_64 #1
Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 04/05/2016
Call Trace:
dump_stack+0x74/0x96
bad_page.cold+0x63/0x94
check_new_page_bad+0x6d/0x80
rmqueue+0x46e/0x970
get_page_from_freelist+0xcb/0x3f0
? _cond_resched+0x19/0x40
__alloc_pages_nodemask+0x164/0x300
alloc_pages_current+0x87/0xf0
skb_page_frag_refill+0x84/0x110
...
Sometimes, it would also show up as corruption in the free list pointer
and cause crashes.
After bisecting the issue, we found the issue started from commit e320d3012d25 ("mm/page_alloc.c: fix freeing non-compound pages"):
if (put_page_testzero(page))
free_the_page(page, order);
else if (!PageHead(page))
while (order-- > 0)
free_the_page(page + (1 << order), order);
So the problem is the check PageHead is racy because at this point we
already dropped our reference to the page. So even if we came in with
compound page, the page can already be freed and PageHead can return
false and we will end up freeing all the tail pages causing double free.
The usage of edge-triggered interrupts lead to lost interrupts under load,
see [0]. This was confirmed to be fixed by using level-triggered
interrupts.
The report was about SDIO. However, as the host controller is the same
for SD and MMC, apply the change to all mmc controller instances.
The usage of edge-triggered interrupts lead to lost interrupts under load,
see [0]. This was confirmed to be fixed by using level-triggered
interrupts.
The report was about SDIO. However, as the host controller is the same
for SD and MMC, apply the change to all mmc controller instances.
The usage of edge-triggered interrupts lead to lost interrupts under load,
see [0]. This was confirmed to be fixed by using level-triggered
interrupts.
The report was about SDIO. However, as the host controller is the same
for SD and MMC, apply the change to all mmc controller instances.
In commit 588a513d3425 ("arm64: Fix race condition on PG_dcache_clean
in __sync_icache_dcache()"), we found RISC-V has the same issue as the
previous arm64. The previous implementation didn't guarantee the correct
sequence of operations, which means flush_icache_all() hasn't been
called when the PG_dcache_clean was set. That would cause a risk of page
synchronization.
Fixes: 08f051eda33b ("RISC-V: Flush I$ when making a dirty page executable") Signed-off-by: Guo Ren <guoren@linux.alibaba.com> Signed-off-by: Guo Ren <guoren@kernel.org> Reviewed-by: Andrew Jones <ajones@ventanamicro.com> Reviewed-by: Conor Dooley <conor.dooley@microchip.com> Link: https://lore.kernel.org/r/20230127035306.1819561-1-guoren@kernel.org Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While checking Pin Assignments of the port and partner during probe, we
don't take into account whether the peripheral is a plug or receptacle.
This manifests itself in a mode entry failure on certain docks and
dongles with captive cables. For instance, the Startech.com Type-C to DP
dongle (Model #CDP2DP) advertises its DP VDO as 0x405. This would fail
the Pin Assignment compatibility check, despite it supporting
Pin Assignment C as a UFP.
Update the check to use the correct DP Pin Assign macros that
take the peripheral's receptacle bit into account.
The Alcor Link AK9563 smartcard reader used on some Lenovo platforms
doesn't work. If LPM is enabled the reader will provide an invalid
usb config descriptor. Added quirk to disable LPM.
Verified fix on Lenovo P16 G1 and T14 G3
Tested-by: Miroslav Zatko <mzatko@mirexoft.com> Tested-by: Dennis Wassenberg <dennis.wassenberg@secunet.com> Cc: stable@vger.kernel.org Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com> Signed-off-by: Mark Pearson <mpearson-lenovo@squebb.ca> Link: https://lore.kernel.org/r/20230208181223.1092654-1-mpearson-lenovo@squebb.ca Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have this check to make sure we don't accidentally add older devices
that may have disappeared and re-appeared with an older generation from
being added to an fs_devices (such as a replace source device). This
makes sense, we don't want stale disks in our file system. However for
single disks this doesn't really make sense.
I've seen this in testing, but I was provided a reproducer from a
project that builds btrfs images on loopback devices. The loopback
device gets cached with the new generation, and then if it is re-used to
generate a new file system we'll fail to mount it because the new fs is
"older" than what we have in cache.
Fix this by freeing the cache when closing the device for a single device
filesystem. This will ensure that the mount command passed device path is
scanned successfully during the next mount.
CC: stable@vger.kernel.org # 5.10+ Reported-by: Daan De Meyer <daandemeyer@fb.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The syzbot fuzzer detected a bug in the plusb network driver: A
zero-length control-OUT transfer was treated as a read instead of a
write. In modern kernels this error provokes a WARNING:
Last potentially related work creation:
kasan_save_stack+0x22/0x50
__kasan_record_aux_stack+0x95/0xb0
insert_work+0x2b/0x130
__queue_work+0x1fe/0x660
queue_work_on+0x4b/0x60
smb2_readv_callback+0x396/0x800
cifs_abort_connection+0x474/0x6a0
cifs_reconnect+0x5cb/0xa50
cifs_readv_from_socket.cold+0x22/0x6c
cifs_read_page_from_socket+0xc1/0x100
readpages_fill_pages.cold+0x2f/0x46
cifs_readv_receive+0x46d/0xa40
cifs_demultiplex_thread+0x121c/0x1490
kthread+0x16b/0x1a0
ret_from_fork+0x2c/0x50
The following function calls will cause UAF of the rdata pointer.
readpages_fill_pages
cifs_read_page_from_socket
cifs_readv_from_socket
cifs_reconnect
__cifs_reconnect
cifs_abort_connection
mid->callback() --> smb2_readv_callback
queue_work(&rdata->work) # if the worker completes first,
# the rdata is freed
cifs_readv_complete
kref_put
cifs_readdata_release
kfree(rdata)
return rdata->... # UAF in readpages_fill_pages()
Similarly, this problem also occurs in the uncache_fill_pages().
Fix this by adjusts the order of condition judgment in the return
statement.
Signed-off-by: ZhaoLong Wang <wangzhaolong1@huawei.com> Cc: stable@vger.kernel.org Acked-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to using the u16 type in the min_t() macros the SPI transfer length
will be cast to word before participating in the conditional statement
implied by the macro. Thus if the transfer length is greater than 64KB the
Tx/Rx FIFO threshold level value will be determined by the leftover of the
truncated after the type-case length. In the worst case it will cause the
dramatical performance drop due to the "Tx FIFO Empty" or "Rx FIFO Full"
interrupts triggered on each xfer word sent/received to/from the bus.
The problem can be easily fixed by specifying the unsigned int type in the
min_t() macros thus preventing the possible data loss.
Fixes: ea11370fffdf ("spi: dw: get TX level without an additional variable") Reported-by: Sergey Nazarov <Sergey.Nazarov@baikalelectronics.ru> Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20230113185942.2516-1-Sergey.Semin@baikalelectronics.ru Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Added checking of pointer "function" in pcs_set_mux().
pinmux_generic_get_function() can return NULL and the pointer
"function" was dereferenced without checking against NULL.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 571aec4df5b7 ("pinctrl: single: Use generic pinmux helpers for managing functions") Signed-off-by: Maxim Korotkov <korotkov.maxim.s@gmail.com> Reviewed-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20221118104332.943-1-korotkov.maxim.s@gmail.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This loop accidentally reuses the "i" iterator for both the inside and
the outside loop. The value of MAX_STREAM_BUFFER is 5. I believe that
chip->rmh.stat_len is in the 2-12 range. If the value of .stat_len is
4 or more then it will loop exactly one time, but if it's less then it
is a forever loop.
It looks like it was supposed to combined into one loop where
conditions are checked.
rds_rm_zerocopy_callback() uses list_entry() on the head of a list
causing a type confusion.
Use list_first_entry() to actually access the first element of the
rs_zcookie_queue list.
Fixes: 9426bbc6de99 ("rds: use list structure to track information for zerocopy completion notification") Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Link: https://lore.kernel.org/r/20230202-rds-zerocopy-v3-1-83b0df974f9a@diag.uniroma1.it Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When tracer is reloaded, the device will log the traces at the
beginning of the log buffer. Also, driver is reading the log buffer in
chunks in accordance to the consumer index.
Hence, zero consumer index when reloading the tracer.
Whenever the driver is reading the string DBs into buffers, the driver
is setting the load bit, but the driver never clears this bit.
As a result, in case load bit is on and the driver query the device for
new string DBs, the driver won't read again the string DBs.
Fix it by clearing the load bit when query the device for new string
DBs.
Fixes: 2d69356752ff ("net/mlx5: Add support for fw live patch event") Signed-off-by: Shay Drory <shayd@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
ethtool is returning an error for unknown speeds for the IPoIB interface:
$ ethtool ib0
netlink error: failed to retrieve link settings
netlink error: Invalid argument
netlink error: failed to retrieve link settings
netlink error: Invalid argument
Settings for ib0:
Link detected: no
After this change, ethtool will return success and show "unknown speed":
$ ethtool ib0
Settings for ib0:
Supported ports: [ ]
Supported link modes: Not reported
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: Unknown!
Duplex: Full
Auto-negotiation: off
Port: Other
PHYAD: 0
Transceiver: internal
Link detected: no
Fixes: eb234ee9d541 ("net/mlx5e: IPoIB, Add support for get_link_ksettings in ethtool") Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com> Reviewed-by: Gal Pressman <gal@nvidia.com> Reviewed-by: Tariq Toukan <tariqt@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Alternative short title: don't instruct the hardware to match on
EtherType with "protocol 802.1Q" flower filters. It doesn't work for the
reasons detailed below.
the created filter is set by ocelot_flower_parse_key() to be of type
OCELOT_VCAP_KEY_ETYPE, and etype is set to {value=0x8100, mask=0xffff}.
This gets propagated all the way to is1_entry_set() which commits it to
hardware (the VCAP_IS1_HK_ETYPE field of the key). Compare this to the
case where src_mac isn't specified - the key type is OCELOT_VCAP_KEY_ANY,
and is1_entry_set() doesn't populate VCAP_IS1_HK_ETYPE.
The problem is that for VLAN-tagged frames, the hardware interprets the
ETYPE field as holding the encapsulated VLAN protocol. So the above
filter will only match those packets which have an encapsulated protocol
of 0x8100, rather than all packets with VLAN ID 200 and the given src_mac.
The reason why this is allowed to occur is because, although we have a
block of code in ocelot_flower_parse_key() which sets "match_protocol"
to false when VLAN keys are present, that code executes too late.
There is another block of code, which executes for Ethernet addresses,
and has a "goto finished_key_parsing" and skips the VLAN header parsing.
By skipping it, "match_protocol" remains with the value it was
initialized with, i.e. "true", and "proto" is set to f->common.protocol,
or 0x8100.
The concept of ignoring some keys rather than erroring out when they are
present but can't be offloaded is dubious in itself, but is present
since the initial commit fe3490e6107e ("net: mscc: ocelot: Hardware
ofload for tc flower filter"), and it's outside of the scope of this
patch to change that.
The problem was introduced when the driver started to interpret the
flower filter's protocol, and populate the VCAP filter's ETYPE field
based on it.
To fix this, it is sufficient to move the code that parses the VLAN keys
earlier than the "goto finished_key_parsing" instruction. This will
ensure that if we have a flower filter with both VLAN and Ethernet
address keys, it won't match on ETYPE 0x8100, because the VLAN key
parsing sets "match_protocol = false".
Fixes: 86b956de119c ("net: mscc: ocelot: support matching on EtherType") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230205192409.1796428-1-vladimir.oltean@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When both ice and the irdma driver are loaded, a warning in
check_flush_dependency is being triggered. This is due to ice driver
workqueue being allocated with the WQ_MEM_RECLAIM flag and the irdma one
is not.
According to kernel documentation, this flag should be set if the
workqueue will be involved in the kernel's memory reclamation flow.
Since it is not, there is no need for the ice driver's WQ to have this
flag set so remove it.
Since commit 58e0be1ef6118 ("net: use struct_group to copy ip/ipv6
header addresses"), ip and ipv6 headers started to use the __struct_group
definition, which is defined at include/uapi/linux/stddef.h. However,
linux/stddef.h isn't explicitly included in include/uapi/linux/{ip,ipv6}.h,
which breaks build of xskxceiver bpf selftest if you install the uapi
headers in the system:
$ make V=1 xskxceiver -C tools/testing/selftests/bpf
...
make: Entering directory '(...)/tools/testing/selftests/bpf'
gcc -g -O0 -rdynamic -Wall -Werror (...)
In file included from xskxceiver.c:79:
/usr/include/linux/ip.h:103:9: error: expected specifier-qualifier-list before ‘__struct_group’
103 | __struct_group(/* no tag */, addrs, /* no attrs */,
| ^~~~~~~~~~~~~~
...
Include the missing <linux/stddef.h> dependency in ip.h and do the
same for the ipv6.h header.
Fixes: 58e0be1ef611 ("net: use struct_group to copy ip/ipv6 header addresses") Signed-off-by: Herton R. Krzesinski <herton@redhat.com> Reviewed-by: Carlos O'Donell <carlos@redhat.com> Tested-by: Carlos O'Donell <carlos@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clear the interrupt credits before enabling the queue rather
than after to be sure that the enabled queue starts at 0 and
that we don't wipe away possible credits after enabling the
queue.
Fixes: 0f3154e6bcb3 ("ionic: Add Tx and Rx handling") Signed-off-by: Neel Patel <neel.patel@amd.com> Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Jerome provided the information that also the GXL internal PHY doesn't
support MMD register access and EEE. MMD reads return 0xffff, what
results in e.g. completely wrong ethtool --show-eee output.
Therefore use the MMD dummy stubs.
Fixes: d853d145ea3e ("net: phy: add an option to disable EEE advertisement") Suggested-by: Jerome Brunet <jbrunet@baylibre.com> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/84432fe4-0be4-bc82-4e5c-557206b40f56@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit ff9fb72bc077 ("debugfs: return error values,
not NULL") changed return value of debugfs_rename() in
error cases from %NULL to %ERR_PTR(-ERROR), we should
also check error values instead of NULL.
Fixes: ff9fb72bc077 ("debugfs: return error values, not NULL") Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Link: https://lore.kernel.org/r/20230202093256.32458-1-zhengqi.arch@bytedance.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When copying the DSCP bits for decap-dscp into IPv6 don't assume the
outer encap is always IPv6. Instead, as with the inner IPv4 case, copy
the DSCP bits from the correctly saved "tos" value in the control block.
Fixes: 227620e29509 ("[IPSEC]: Separate inner/outer mode processing on input") Signed-off-by: Christian Hopps <chopps@chopps.org> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
usnic_uiom_map_sorted_intervals() is called under spin_lock(), iommu_map()
might sleep, use iommu_map_atomic() to avoid potential sleep in atomic
context.
The cited commit creates child PKEY interfaces over netlink will
multiple tx and rx queues, but some devices doesn't support more than 1
tx and 1 rx queues. This causes to a crash when traffic is sent over the
PKEY interface due to the parent having a single queue but the child
having multiple queues.
This patch fixes the number of queues to 1 for legacy IPoIB at the
earliest possible point in time.
The ISO 11783-5 standard, in "4.5.2 - Address claim requirements", states:
d) No CF shall begin, or resume, transmission on the network until 250
ms after it has successfully claimed an address except when
responding to a request for address-claimed.
But "Figure 6" and "Figure 7" in "4.5.4.2 - Address-claim
prioritization" show that the CF begins the transmission after 250 ms
from the first AC (address-claimed) message even if it sends another AC
message during that time window to resolve the address contention with
another CF.
As stated in "4.4.2.3 - Address-claimed message":
In order to successfully claim an address, the CF sending an address
claimed message shall not receive a contending claim from another CF
for at least 250 ms.
As stated in "4.4.3.2 - NAME management (NM) message":
1) A commanding CF can
d) request that a CF with a specified NAME transmit the address-
claimed message with its current NAME.
2) A target CF shall
d) send an address-claimed message in response to a request for a
matching NAME
Taking the above arguments into account, the 250 ms wait is requested
only during network initialization.
Do not restart the timer on AC message if both the NAME and the address
match and so if the address has already been claimed (timer has expired)
or the AC message has been sent to resolve the contention with another
CF (timer is still running).
Signed-off-by: Devid Antonio Filoni <devid.filoni@egluetechnologies.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Link: https://lore.kernel.org/all/20221125170418.34575-1-devid.filoni@egluetechnologies.com Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 7a8b64d17e35 ("of/address: use range parser for of_dma_get_range")
converted the parsing of dma-range properties to use code shared with the
PCI range parser. The intent was to introduce no functional changes however
in the case where we fail to translate the first resource instead of
returning -EINVAL the new code we return 0. Restore the previous behaviour
by returning an error if we find no valid ranges, the original code only
handled the first range but subsequently support for parsing all supplied
ranges was added.
This avoids confusing code using the parsed ranges which doesn't expect to
successfully parse ranges but have only a list terminator returned, this
fixes breakage with so far as I can tell all DMA for on SoC devices on the
Socionext Synquacer platform which has a firmware supplied DT. A bisect
identified the original conversion as triggering the issues there.
Fixes: 7a8b64d17e35 ("of/address: use range parser for of_dma_get_range") Signed-off-by: Mark Brown <broonie@kernel.org> Cc: Luca Di Stefano <luca.distefano@linaro.org> Cc: 993612@bugs.debian.org Cc: stable@kernel.org Link: https://lore.kernel.org/r/20230126-synquacer-boot-v2-1-cb80fd23c4e2@kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
poll() and select() on per_cpu trace_pipe and trace_pipe_raw do not work
since kernel 6.1-rc6. This issue is seen after the commit 42fb0a1e84ff525ebe560e2baf9451ab69127e2b ("tracing/ring-buffer: Have
polling block on watermark").
This issue is firstly detected and reported, when testing the CXL error
events in the rasdaemon and also erified using the test application for poll()
and select().
This issue occurs for the per_cpu case, when calling the ring_buffer_poll_wait(),
in kernel/trace/ring_buffer.c, with the buffer_percent > 0 and then wait until the
percentage of pages are available. The default value set for the buffer_percent is 50
in the kernel/trace/trace.c.
As a fix, allow userspace application could set buffer_percent as 0 through
the buffer_percent_fops, so that the task will wake up as soon as data is added
to any of the specific cpu buffer.
Link: https://lore.kernel.org/linux-trace-kernel/20230202182309.742-2-shiju.jose@huawei.com Cc: <mhiramat@kernel.org> Cc: <mchehab@kernel.org> Cc: <linux-edac@vger.kernel.org> Cc: stable@vger.kernel.org Fixes: 42fb0a1e84ff5 ("tracing/ring-buffer: Have polling block on watermark") Signed-off-by: Shiju Jose <shiju.jose@huawei.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Samsung Galaxy Book2 Pro 360 (13" 2022 NP930QED-KA1FR) with codec SSID
144d:ca03 requires the same workaround for enabling the speaker amp
like other Samsung models with ALC298 codec.
snd_emux_xg_control() can be called with an argument 'param' greater
than size of 'control' array. It may lead to accessing 'control'
array at a wrong index.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
KMSAN reports uses of uninitialized memory in zlib's longest_match()
called on memory originating from zlib_alloc_workspace().
This issue is known by zlib maintainers and is claimed to be harmless,
but to be on the safe side we'd better initialize the memory.
Link: https://zlib.net/zlib_faq.html#faq36 Reported-by: syzbot+14d9e7602ebdf7ec0a60@syzkaller.appspotmail.com CC: stable@vger.kernel.org # 5.4+ Signed-off-by: Alexander Potapenko <glider@google.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There was a recent regression in btrfs/177 that started happening with
the size class patches ("btrfs: introduce size class to block group
allocator"). This however isn't a regression introduced by those
patches, but rather the bug was uncovered by a change in behavior in
these patches. The patches triggered more chunk allocations in the
^free-space-tree case, which uncovered a race with device shrink.
The problem is we will set the device total size to the new size, and
use this to find a hole for a device extent. However during shrink we
may have device extents allocated past this range, so we could
potentially find a hole in a range past our new shrink size. We don't
actually limit our found extent to the device size anywhere, we assume
that we will not find a hole past our device size. This isn't true with
shrink as we're relocating block groups and thus creating holes past the
device size.
Fix this by making sure we do not search past the new device size, and
if we wander into any device extents that start after our device size
simply break from the loop and use whatever hole we've already found.
CC: stable@vger.kernel.org # 4.14+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
migrate_pages/mempolicy semantics state that CAP_SYS_NICE is required to
move pages shared with another process to a different node. page_mapcount
> 1 is being used to determine if a hugetlb page is shared. However, a
hugetlb page will have a mapcount of 1 if mapped by multiple processes via
a shared PMD. As a result, hugetlb pages shared by multiple processes and
mapped with a shared PMD can be moved by a process without CAP_SYS_NICE.
To fix, check for a shared PMD if mapcount is 1. If a shared PMD is found
consider the page shared.
Link: https://lkml.kernel.org/r/20230126222721.222195-3-mike.kravetz@oracle.com Fixes: e2d8cf405525 ("migrate: add hugepage migration code to migrate_pages()") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Peter Xu <peterx@redhat.com> Acked-by: David Hildenbrand <david@redhat.com> Cc: James Houghton <jthoughton@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev> Cc: Vishal Moola (Oracle) <vishal.moola@gmail.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We might fail to isolate huge page due to e.g. the page is under
migration which cleared HPageMigratable. We should return errno in this
case rather than always return 1 which could confuse the user, i.e. the
caller might think all of the memory is migrated while the hugetlb page is
left behind. We make the prototype of isolate_huge_page consistent with
isolate_lru_page as suggested by Huang Ying and rename isolate_huge_page
to isolate_hugetlb as suggested by Muchun to improve the readability.
Link: https://lkml.kernel.org/r/20220530113016.16663-4-linmiaohe@huawei.com Fixes: e8db67eb0ded ("mm: migrate: move_pages() supports thp migration") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Suggested-by: Huang Ying <ying.huang@intel.com> Reported-by: kernel test robot <lkp@intel.com> (build error) Cc: Alistair Popple <apopple@nvidia.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Christoph Lameter <cl@linux.com> Cc: David Hildenbrand <david@redhat.com> Cc: David Howells <dhowells@redhat.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Oscar Salvador <osalvador@suse.de> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: 73bdf65ea748 ("migrate: hugetlb: check for hugetlb shared PMD in node migration") Signed-off-by: Sasha Levin <sashal@kernel.org>
Below is a simplified case from a report in bcc [0]:
r4 = 20
*(u32 *)(r10 -4) = r4
*(u32 *)(r10 -8) = r4 /* r4 state is tracked */
r4 = *(u64 *)(r10 -8) /* Read more than the tracked 32bit scalar.
* verifier rejects as 'corrupted spill memory'.
*/
After commit 354e8f1970f8 ("bpf: Support <8-byte scalar spill and refill"),
the 8-byte aligned 32bit spill is also tracked by the verifier and the
register state is stored.
However, if 8 bytes are read from the stack instead of the tracked 4 byte
scalar, then verifier currently rejects the program as "corrupted spill
memory". This patch fixes this case by allowing it to read but marks the
register as unknown.
Also note that, if the prog is trying to corrupt/leak an earlier spilled
pointer by spilling another <8 bytes register on top, this has already
been rejected in the check_stack_write_fixed_off().
[0] https://github.com/iovisor/bcc/pull/3683
Fixes: 354e8f1970f8 ("bpf: Support <8-byte scalar spill and refill") Reported-by: Hengqi Chen <hengqi.chen@gmail.com> Reported-by: Yonghong Song <yhs@gmail.com> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Tested-by: Hengqi Chen <hengqi.chen@gmail.com> Acked-by: Yonghong Song <yhs@fb.com> Link: https://lore.kernel.org/bpf/20211102064535.316018-1-kafai@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Wp-gpios property can be used on NVMEM nodes and the same property can
be also used on MTD NAND nodes. In case of the wp-gpios property is
defined at NAND level node, the GPIO management is done at NAND driver
level. Write protect is disabled when the driver is probed or resumed
and is enabled when the driver is released or suspended.
When no partitions are defined in the NAND DT node, then the NAND DT node
will be passed to NVMEM framework. If wp-gpios property is defined in
this node, the GPIO resource is taken twice and the NAND controller
driver fails to probe.
It would be possible to set config->wp_gpio at MTD level before calling
nvmem_register function but NVMEM framework will toggle this GPIO on
each write when this GPIO should only be controlled at NAND level driver
to ensure that the Write Protect has not been enabled.
A way to fix this conflict is to add a new boolean flag in nvmem_config
named ignore_wp. In case ignore_wp is set, the GPIO resource will
be managed by the provider.
Fixes: 2a127da461a9 ("nvmem: add support for the write-protect pin") Cc: stable@vger.kernel.org Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20220220151432.16605-2-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: ab3428cfd9aa ("nvmem: core: fix registration vs use race") Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch fixes slab-out-of-bounds reads in brcmfmac that occur in
brcmf_construct_chaninfo() and brcmf_enable_bw40_2g() when the count
value of channel specifications provided by the device is greater than
the length of 'list->element[]', decided by the size of the 'list'
allocated with kzalloc(). The patch adds checks that make the functions
free the buffer and return -EINVAL if that is the case. Note that the
negative return is handled by the caller, brcmf_setup_wiphybands() or
brcmf_cfg80211_attach().
Found by a modified version of syzkaller.
Crash Report from brcmf_construct_chaninfo():
==================================================================
BUG: KASAN: slab-out-of-bounds in brcmf_setup_wiphybands+0x1238/0x1430
Read of size 4 at addr ffff888115f24600 by task kworker/0:2/1896
The buggy address belongs to the object at ffff888115f24000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1536 bytes inside of
2048-byte region [ffff888115f24000, ffff888115f24800)
Memory state around the buggy address: ffff888115f24500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888115f24580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff888115f24600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff888115f24680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888115f24700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Crash Report from brcmf_enable_bw40_2g():
==================================================================
BUG: KASAN: slab-out-of-bounds in brcmf_cfg80211_attach+0x3d11/0x3fd0
Read of size 4 at addr ffff888103787600 by task kworker/0:2/1896
The buggy address belongs to the object at ffff888103787000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1536 bytes inside of
2048-byte region [ffff888103787000, ffff888103787800)
Memory state around the buggy address: ffff888103787500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffff888103787580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff888103787600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff888103787680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff888103787700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Reported-by: Dokyung Song <dokyungs@yonsei.ac.kr> Reported-by: Jisoo Jang <jisoo.jang@yonsei.ac.kr> Reported-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr> Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20221116142952.518241-1-linuxlovemin@yonsei.ac.kr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The root cause is that we forgot to do sanity check on .i_extra_isize
in below path, result in accessing invalid address later, fix it.
- gc_data_segment
- is_alive
- data_blkaddr
- offset_in_addr
The current error handling code in ufx_usb_probe have many unmatching
issues, e.g., missing ufx_free_usb_list, destroy_modedb label should
only include framebuffer_release, fb_dealloc_cmap only matches
fb_alloc_cmap.
As DMA Rx can be completed from two places, it is possible that DMA Rx
completes before DMA completion callback had a chance to complete it.
Once the previous DMA Rx has been completed, a new one can be started
on the next UART interrupt. The following race is possible
(uart_unlock_and_check_sysrq_irqrestore() replaced with
spin_unlock_irqrestore() for simplicity/clarity):
This race seems somewhat theoretical to occur for real but handle it
correctly regardless. Check what is the DMA status before complething
anything in __dma_rx_complete().
Reported-by: Gilles BULOZ <gilles.buloz@kontron.com> Tested-by: Gilles BULOZ <gilles.buloz@kontron.com> Fixes: 9ee4b83e51f7 ("serial: 8250: Add support for dmaengine") Cc: stable@vger.kernel.org Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Link: https://lore.kernel.org/r/20230130114841.25749-3-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__dma_rx_complete() is called from two places:
- Through the DMA completion callback dma_rx_complete()
- From serial8250_rx_dma_flush() after IIR_RLSI or IIR_RX_TIMEOUT
The former does not hold port's lock during __dma_rx_complete() which
allows these two to race and potentially insert the same data twice.
Extend port's lock coverage in dma_rx_complete() to prevent the race
and check if the DMA Rx is still pending completion before calling
into __dma_rx_complete().
nvmem_add_cells() could return an error after some cells are already
added to the provider. In this case, the added cells are not removed.
Remove any registered cells if nvmem_add_cells() fails.
Fixes: fa72d847d68d7 ("nvmem: check the return value of nvmem_add_cells()") Cc: stable@vger.kernel.org Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20230127104015.23839-9-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error path for wp_gpio attempts to free the IDA nvmem->id, but
this has yet to be assigned, so will always be zero - leaking the
ID allocated by ida_alloc(). Fix this by moving the initialisation
of nvmem->id earlier.
Fixes: f7d8d7dcd978 ("nvmem: fix memory leak in error path") Cc: stable@vger.kernel.org Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20230127104015.23839-4-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A userspace with multiple threads racing I915_GEM_SET_TILING to set the
tiling to I915_TILING_NONE could trigger a double free of the bit_17
bitmask. (Or conversely leak memory on the transition to tiled.) Move
allocation/free'ing of the bitmask within the section protected by the
obj lock.
Signed-off-by: Rob Clark <robdclark@chromium.org> Fixes: 2850748ef876 ("drm/i915: Pull i915_vma_pin under the vm->mutex") Cc: <stable@vger.kernel.org> # v5.5+
[tursulin: Correct fixes tag and added cc stable.] Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230127200550.3531984-1-robdclark@gmail.com
(cherry picked from commit 10e0cbaaf1104f449d695c80bcacf930dcd3c42e) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A Sysbot [1] corrupted filesystem exposes two flaws in the handling and
sanity checking of the xattr_ids count in the filesystem. Both of these
flaws cause computation overflow due to incorrect typing.
In the corrupted filesystem the xattr_ids value is 4294967071, which
stored in a signed variable becomes the negative number -225.
Flaw 1 (64-bit systems only):
The signed integer xattr_ids variable causes sign extension.
This causes variable overflow in the SQUASHFS_XATTR_*(A) macros. The
variable is first multiplied by sizeof(struct squashfs_xattr_id) where the
type of the sizeof operator is "unsigned long".
On a 64-bit system this is 64-bits in size, and causes the negative number
to be sign extended and widened to 64-bits and then become unsigned. This
produces the very large number 18446744073709548016 or 2^64 - 3600. This
number when rounded up by SQUASHFS_METADATA_SIZE - 1 (8191 bytes) and
divided by SQUASHFS_METADATA_SIZE overflows and produces a length of 0
(stored in len).
Flaw 2 (32-bit systems only):
On a 32-bit system the integer variable is not widened by the unsigned
long type of the sizeof operator (32-bits), and the signedness of the
variable has no effect due it always being treated as unsigned.
The above corrupted xattr_ids value of 4294967071, when multiplied
overflows and produces the number 4294963696 or 2^32 - 3400. This number
when rounded up by SQUASHFS_METADATA_SIZE - 1 (8191 bytes) and divided by
SQUASHFS_METADATA_SIZE overflows again and produces a length of 0.
The effect of the 0 length computation:
In conjunction with the corrupted xattr_ids field, the filesystem also has
a corrupted xattr_table_start value, where it matches the end of
filesystem value of 850.
This causes the following sanity check code to fail because the
incorrectly computed len of 0 matches the incorrect size of the table
reported by the superblock (0 bytes).
len = SQUASHFS_XATTR_BLOCK_BYTES(*xattr_ids);
indexes = SQUASHFS_XATTR_BLOCKS(*xattr_ids);
/*
* The computed size of the index table (len bytes) should exactly
* match the table start and end points
*/
start = table_start + sizeof(*id_table);
end = msblk->bytes_used;
if (len != (end - start))
return ERR_PTR(-EINVAL);
Changing the xattr_ids variable to be "usigned int" fixes the flaw on a
64-bit system. This relies on the fact the computation is widened by the
unsigned long type of the sizeof operator.
Casting the variable to u64 in the above macro fixes this flaw on a 32-bit
system.
It also means 64-bit systems do not implicitly rely on the type of the
sizeof operator to widen the computation.
The softlockup still occurs in get_swap_pages() under memory pressure. 64
CPU cores, 64GB memory, and 28 zram devices, the disksize of each zram
device is 50MB with same priority as si. Use the stress-ng tool to
increase memory pressure, causing the system to oom frequently.
The plist_for_each_entry_safe() loops in get_swap_pages() could reach tens
of thousands of times to find available space (extreme case:
cond_resched() is not called in scan_swap_map_slots()). Let's add
cond_resched() into get_swap_pages() when failed to find available space
to avoid softlockup.
In case of error, the function stratix10_svc_allocate_memory()
returns ERR_PTR() and never returns NULL. The NULL test in the
return value check should be replaced with IS_ERR().
In kernels compiled with CONFIG_PARAVIRT=n, the compiler re-orders the
DR7 read in exc_nmi() to happen before the call to sev_es_ist_enter().
This is problematic when running as an SEV-ES guest because in this
environment the DR7 read might cause a #VC exception, and taking #VC
exceptions is not safe in exc_nmi() before sev_es_ist_enter() has run.
The result is stack recursion if the NMI was caused on the #VC IST
stack, because a subsequent #VC exception in the NMI handler will
overwrite the stack frame of the interrupted #VC handler.
As there are no compiler barriers affecting the ordering of DR7
reads/writes, make the accesses to this register volatile, forbidding
the compiler to re-order them.
[ bp: Massage text, make them volatile too, to make sure some
aggressive compiler optimization pass doesn't discard them. ]
Patch series "Fixes for hugetlb mapcount at most 1 for shared PMDs".
This issue of mapcount in hugetlb pages referenced by shared PMDs was
discussed in [1]. The following two patches address user visible behavior
caused by this issue.
A hugetlb page will have a mapcount of 1 if mapped by multiple processes
via a shared PMD. This is because only the first process increases the
map count, and subsequent processes just add the shared PMD page to their
page table.
page_mapcount is being used to decide if a hugetlb page is shared or
private in /proc/PID/smaps. Pages referenced via a shared PMD were
incorrectly being counted as private.
To fix, check for a shared PMD if mapcount is 1. If a shared PMD is found
count the hugetlb page as shared. A new helper to check for a shared PMD
is added.
[akpm@linux-foundation.org: simplification, per David]
[akpm@linux-foundation.org: hugetlb.h: include page_ref.h for page_count()] Link: https://lkml.kernel.org/r/20230126222721.222195-2-mike.kravetz@oracle.com Fixes: 25ee01a2fca0 ("mm: hugetlb: proc: add hugetlb-related fields to /proc/PID/smaps") Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com> Acked-by: Peter Xu <peterx@redhat.com> Cc: David Hildenbrand <david@redhat.com> Cc: James Houghton <jthoughton@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Muchun Song <songmuchun@bytedance.com> Cc: Naoya Horiguchi <naoya.horiguchi@linux.dev> Cc: Vishal Moola (Oracle) <vishal.moola@gmail.com> Cc: Yang Shi <shy828301@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC 13 will enable -fasynchronous-unwind-tables by default on riscv. In
the kernel, we don't have any use for unwind tables yet, so disable them.
More importantly, the .eh_frame section brings relocations
(R_RISC_32_PCREL, R_RISCV_SET{6,8,16}, R_RISCV_SUB{6,8,16}) into modules
that we are not prepared to handle.
Wire up the missing ptrace requests PTRACE_GETREGS, PTRACE_SETREGS,
PTRACE_GETFPREGS and PTRACE_SETFPREGS when running 32-bit applications
on 64-bit kernels.
+/-1200uT is a MAGN sensor full measurement range. Magnetometer scale
is the magnetic sensitivity parameter. It is referenced as 0.1uT
according to datasheet and magnetometer channel unit is Gauss in
sysfs-bus-iio documentation. Gauss and uTesla unit conversion
relationship as follows: 0.1uT = 0.001Gs.
Set magnetometer scale and available magnetometer scale as fixed 0.001Gs.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU") Signed-off-by: Carlos Song <carlos.song@nxp.com> Link: https://lore.kernel.org/r/20230118074227.1665098-5-carlos.song@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FXOS8700_CTRL_ODR_MIN is not used but value is probably wrong.
Remove it for a good readability.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU") Signed-off-by: Carlos Song <carlos.song@nxp.com> Link: https://lore.kernel.org/r/20230118074227.1665098-4-carlos.song@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The absence of correct offset leads a failed initialization ODR mode
assignment.
Select MAX ODR mode as the initialization ODR mode by field mask and
FIELD_PREP.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU") Signed-off-by: Carlos Song <carlos.song@nxp.com> Link: https://lore.kernel.org/r/20230118074227.1665098-3-carlos.song@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The absence of a correct offset leads an incorrect ODR mode
readback after use a hexadecimal number to mark the value from
FXOS8700_CTRL_REG1.
Get ODR mode by field mask and FIELD_GET clearly and conveniently.
And attach other additional fix for keeping the original code logic
and a good readability.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU") Signed-off-by: Carlos Song <carlos.song@nxp.com> Link: https://lore.kernel.org/r/20230118074227.1665098-2-carlos.song@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because ACCEL and MAGN channels data register base address is
swapped the accelerometer and magnetometer channels readback is
swapped.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU") Signed-off-by: Carlos Song <carlos.song@nxp.com> Link: https://lore.kernel.org/r/20221208071911.2405922-3-carlos.song@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
FXOS8700 is an IMU sensor with ACCEL sensor and MAGN sensor.
Sensor type is indexed by corresponding channel type in a switch.
IIO_ANGL_VEL channel type mapped to MAGN sensor has caused confusion.
Fix the mapping label of "IIO_MAGN" channel type instead of
"IIO_ANGL_VEL" channel type to MAGN sensor.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU") Signed-off-by: Carlos Song <carlos.song@nxp.com> Link: https://lore.kernel.org/r/20221208071911.2405922-2-carlos.song@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACCEL output data registers contain the X-axis, Y-axis, and Z-axis
14-bit left-justified sample data and MAGN output data registers
contain the X-axis, Y-axis, and Z-axis 16-bit sample data. The ACCEL
raw register output data should be divided by 4 before sent to
userspace.
Apply a 2 bits signed right shift to the raw data from ACCEL output
data register but keep that from MAGN sensor as the origin.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU") Signed-off-by: Carlos Song <carlos.song@nxp.com> Link: https://lore.kernel.org/r/20221208071911.2405922-5-carlos.song@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The length of ACCEL and MAGN 3-axis channels output data is 6 byte
individually. However block only read 3 bytes data into buffer from
ACCEL or MAGN output data registers every time. It causes an incomplete
ACCEL and MAGN channels readback.
Set correct value count for regmap_bulk_read to get 6 bytes ACCEL and
MAGN channels readback.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU") Signed-off-by: Carlos Song <carlos.song@nxp.com> Link: https://lore.kernel.org/r/20221208071911.2405922-4-carlos.song@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device is in active mode, it fails to set an ACCEL full-scale
range(2g/4g/8g) in FXOS8700_XYZ_DATA_CFG. This is not align with the
datasheet, but it is a fxos8700 chip behavior.
Keep the device in standby mode before setting ACCEL full-scale range
into FXOS8700_XYZ_DATA_CFG in chip initialization phase and setting
scale phase.
Fixes: 84e5ddd5c46e ("iio: imu: Add support for the FXOS8700 IMU") Signed-off-by: Carlos Song <carlos.song@nxp.com> Link: https://lore.kernel.org/r/20221208071911.2405922-6-carlos.song@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_get_parent() will return a device_node pointer with refcount
incremented. We need to use of_node_put() on it when done. Add the
missing of_node_put() in the error path of berlin2_adc_probe();
Fixes: 70f1937911ca ("iio: adc: add support for Berlin") Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com> Link: https://lore.kernel.org/r/20221129020316.191731-1-wangxiongfeng2@huawei.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UEFI v2.10 introduces version 2 of the memory attributes table, which
turns the reserved field into a flags field, but is compatible with
version 1 in all other respects. So let's not complain about version 2
if we encounter it.
The DIAG 288 statement consumes an EBCDIC string the address of which is
passed in a register. Use a "memory" clobber to tell the compiler that
memory is accessed within the inline assembly.
With CONFIG_VMAP_STACK=y the stack is allocated from the vmalloc space.
Data passed to a hardware or a hypervisor interface that
requires V=R can no longer be allocated on the stack.
Use kmalloc() to get memory for a diag288 command.
blit_x and blit_y are u32, so fbcon currently cannot support fonts
larger than 32x32.
The 32x32 case also needs shifting an unsigned int, to properly set bit
31, otherwise we get "UBSAN: shift-out-of-bounds in fbcon_set_font",
as reported on:
A lot of modern Clevo barebones have touchpad and/or keyboard issues after
suspend fixable with nomux + reset + noloop + nopnp. Luckily, none of them
have an external PS/2 port so this can safely be set for all of them.
I'm not entirely sure if every device listed really needs all four quirks,
but after testing and production use. No negative effects could be
observed when setting all four.
The list is quite massive as neither the TUXEDO nor the Clevo dmi strings
have been very consistent historically. I tried to keep the list as short
as possible without risking on missing an affected device.
This is revision 3. The Clevo N150CU barebone is still removed as it might
have problems with the fix and needs further investigations. The
SchenkerTechnologiesGmbH System-/Board-Vendor string variations are
added. This is now based in the quirk table refactor. This now also
includes the additional noaux flag for the NS7xMU.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20220629112725.12922-5-wse@tuxedocomputers.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637c9 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table") Signed-off-by: Sasha Levin <sashal@kernel.org>
Merge i8042 quirk tables to reduce code duplication for devices that need
more than one quirk. Before every quirk had its own table with devices
needing that quirk. If a new quirk needed to be added a new table had to
be created. When a device needed multiple quirks, it appeared in multiple
tables. Now only one table called i8042_dmi_quirk_table exists. In it every
device has one entry and required quirks are coded in the .driver_data
field of the struct dmi_system_id used by this table. Multiple quirks for
one device can be applied by bitwise-or of the new SERIO_QUIRK_* defines.
Also align quirkable options with command line parameters and make vendor
wide quirks per device overwriteable on a per device basis. The first match
is honored while following matches are ignored. So when a vendor wide quirk
is defined in the table, a device can inserted before and therefore
ignoring the vendor wide define.
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20220629112725.12922-3-wse@tuxedocomputers.com Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Stable-dep-of: 9c445d2637c9 ("Input: i8042 - add Clevo PCX0DX to i8042 quirk table") Signed-off-by: Sasha Levin <sashal@kernel.org>
After a call to console_unlock() in vcs_read() the vc_data struct can be
freed by vc_deallocate(). Because of that, the struct vc_data pointer
load must be done at the top of while loop in vcs_read() to avoid a UAF
when vcs_size() is called.
Syzkaller reported a UAF in vcs_size().
BUG: KASAN: use-after-free in vcs_size (drivers/tty/vt/vc_screen.c:215)
Read of size 4 at addr ffff8881137479a8 by task 4a005ed81e27e65/1537
The buggy address belongs to the object at ffff888113747800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 424 bytes inside of
1024-byte region [ffff888113747800, ffff888113747c00)
__ffs_ep0_queue_wait executes holding the spinlock of &ffs->ev.waitq.lock
and unlocks it after the assignments to usb_request are done.
However in the code if the request is already NULL we bail out returning
-EINVAL but never unlocked the spinlock.
Fix this by adding spin_unlock_irq &ffs->ev.waitq.lock before returning.
When STM32 DFSDM driver is built as module, no modalias information
is available. This prevents module to be loaded by udev.
Add MODULE_DEVICE_TABLE() to fill module aliases.
When listen() and accept() are called on an x25 socket
that connect() succeeds, accept() succeeds immediately.
This is because x25_connect() queues the skb to
sk->sk_receive_queue, and x25_accept() dequeues it.
This creates a child socket with the sk of the parent
x25 socket, which can cause confusion.
Fix x25_listen() to return -EINVAL if the socket has
already been successfully connect()ed to avoid this issue.
Signed-off-by: Hyunwoo Kim <v4bel@theori.io> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix multiple W=1 kernel-doc warnings in i2c-rk3x.c:
drivers/i2c/busses/i2c-rk3x.c:83: warning: missing initial short description on line:
* struct i2c_spec_values:
drivers/i2c/busses/i2c-rk3x.c:139: warning: missing initial short description on line:
* struct rk3x_i2c_calced_timings:
drivers/i2c/busses/i2c-rk3x.c:162: warning: missing initial short description on line:
* struct rk3x_i2c_soc_data:
drivers/i2c/busses/i2c-rk3x.c:242: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Generate a START condition, which triggers a REG_INT_START interrupt.
drivers/i2c/busses/i2c-rk3x.c:261: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Generate a STOP condition, which triggers a REG_INT_STOP interrupt.
drivers/i2c/busses/i2c-rk3x.c:304: warning: expecting prototype for Setup a read according to i2c(). Prototype was for rk3x_i2c_prepare_read() instead
drivers/i2c/busses/i2c-rk3x.c:335: warning: expecting prototype for Fill the transmit buffer with data from i2c(). Prototype was for rk3x_i2c_fill_transmit_buf() instead
drivers/i2c/busses/i2c-rk3x.c:535: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Get timing values of I2C specification
drivers/i2c/busses/i2c-rk3x.c:552: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Calculate divider values for desired SCL frequency
drivers/i2c/busses/i2c-rk3x.c:713: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Calculate timing values for desired SCL frequency
drivers/i2c/busses/i2c-rk3x.c:963: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Setup I2C registers for an I2C operation specified by msgs, num.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If during iscsi_sw_tcp_session_create() iscsi_tcp_r2tpool_alloc() fails,
userspace could be accessing the host's ipaddress attr. If we then free the
session via iscsi_session_teardown() while userspace is still accessing the
session we will hit a use after free bug.
Set the tcp_sw_host->session after we have completed session creation and
can no longer fail.
Link: https://lore.kernel.org/r/20230117193937.21244-3-michael.christie@oracle.com Signed-off-by: Mike Christie <michael.christie@oracle.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Acked-by: Ding Hui <dinghui@sangfor.com.cn> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Calling spin_lock_irqsave() does not disable the interrupts on realtime
kernels, remove the warning and replace assert_spin_locked() with
lockdep_assert_held().
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20230110125310.55884-1-mlombard@redhat.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure that xdp_do_flush() is always executed before
napi_complete_done(). This is important for two reasons. First, a
redirect to an XSKMAP assumes that a call to xdp_do_redirect() from
napi context X on CPU Y will be followed by a xdp_do_flush() from the
same napi context and CPU. This is not guaranteed if the
napi_complete_done() is executed before xdp_do_flush(), as it tells
the napi logic that it is fine to schedule napi context X on another
CPU. Details from a production system triggering this bug using the
veth driver can be found following the first link below.
The second reason is that the XDP_REDIRECT logic in itself relies on
being inside a single NAPI instance through to the xdp_do_flush() call
for RCU protection of all in-kernel data structures. Details can be
found in the second link below.
When iterating on a linked list, a result of memremap is dereferenced
without checking it for NULL.
This patch adds a check that falls back on allocating a new page in
case memremap doesn't succeed.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 18df7577adae ("efi/memreserve: deal with memreserve entries in unmapped memory") Signed-off-by: Anton Gusev <aagusev@ispras.ru>
[ardb: return -ENOMEM instead of breaking out of the loop] Signed-off-by: Ard Biesheuvel <ardb@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log