In commit a44be64bbecb ("ext4: don't clear SB_RDONLY when remounting
r/w until quota is re-enabled") we defer clearing tyhe SB_RDONLY flag
in struct super. However, we didn't defer when we checked sb_rdonly()
to determine the lazy itable init thread should be enabled, with the
next result that the lazy inode table initialization would not be
properly started. This can cause generic/231 to fail in ext4's
nojournal mode.
Fix this by moving when we decide to start or stop the lazy itable
init thread to after we clear the SB_RDONLY flag when we are
remounting the file system read/write.
Fixes a44be64bbecb ("ext4: don't clear SB_RDONLY when remounting r/w until...")
Copy the incoming @data comman to an internal buffer so that callers can
put SEV command buffers on the stack without running afoul of
CONFIG_VMAP_STACK=y, i.e. without bombing on vmalloc'd pointers. As of
today, the largest supported command takes a 68 byte buffer, i.e. pretty
much every command can be put on the stack. Because sev_cmd_mutex is
held for the entirety of a transaction, only a single bounce buffer is
required.
Use the internal buffer unconditionally, as the majority of in-kernel
users will soon switch to using the stack. At that point, checking
virt_addr_valid() becomes (negligible) overhead in most cases, and
supporting both paths slightly increases complexity. Since the commands
are all quite small, the cost of the copies is insignificant compared to
the latency of communicating with the PSP.
Allocate a full page for the buffer as opportunistic preparation for
SEV-SNP, which requires the command buffer to be in firmware state for
commands that trigger memory writes from the PSP firmware. Using a full
page now will allow SEV-SNP support to simply transition the page as
needed.
Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Borislav Petkov <bp@suse.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210406224952.4177376-5-seanjc@google.com> Reviewed-by: Brijesh Singh <brijesh.singh@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Ben Hutchings <benh@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARN on and reject SEV commands that provide a valid data pointer, but do
not have a known, non-zero length. And conversely, reject commands that
take a command buffer but none is provided (data is null).
Aside from sanity checking input, disallowing a non-null pointer without
a non-zero size will allow a future patch to cleanly handle vmalloc'd
data by copying the data to an internal __pa() friendly buffer.
Note, this also effectively prevents callers from using commands that
have a non-zero length and are not known to the kernel. This is not an
explicit goal, but arguably the side effect is a good thing from the
kernel's perspective.
Cc: Brijesh Singh <brijesh.singh@amd.com> Cc: Borislav Petkov <bp@suse.de> Cc: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210406224952.4177376-4-seanjc@google.com> Reviewed-by: Brijesh Singh <brijesh.singh@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Ben Hutchings <benh@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Hutchings [Sat, 27 May 2023 13:52:48 +0000 (15:52 +0200)]
scsi: dpt_i2o: Do not process completions with invalid addresses
adpt_isr() reads reply addresses from a hardware register, which
should always be within the DMA address range of the device's pool of
reply address buffers. In case the address is out of range, it tries
to muddle on, converting to a virtual address using bus_to_virt().
bus_to_virt() does not take DMA addresses, and it doesn't make sense
to try to handle the completion in this case. Ignore it and continue
looping to service the interrupt. If a completion has been lost then
the SCSI core should eventually time-out and trigger a reset.
There is no corresponding upstream commit, because this driver was
removed upstream.
Fixes: 67af2b060e02 ("[SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt ...") Signed-off-by: Ben Hutchings <benh@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
adpt_i2o_passthru() takes a user-provided message and passes it
through to the hardware with appropriate translation of addresses
and message IDs. It has a number of bugs:
- When a message requires scatter/gather, it doesn't verify that the
offset to the scatter/gather list is less than the message size.
- When a message requires scatter/gather, it overwrites the DMA
addresses with the user-space virtual addresses before unmapping the
DMA buffers.
- It reads the message from user memory multiple times. This allows
user-space to change the message and bypass validation.
- It assumes that the message is at least 4 words long, but doesn't
check that.
I tried fixing these, but even the maintainer of the corresponding
user-space in Debian doesn't have the hardware any more.
Instead, remove the pass-through ioctl (I2OUSRCMD) and supporting
code.
There is no corresponding upstream commit, because this driver was
removed upstream.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: 67af2b060e02 ("[SCSI] dpt_i2o: move from virt_to_bus/bus_to_virt ...") Signed-off-by: Ben Hutchings <benh@debian.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The meaning of the 'imply' keyword has changed recently, and neither the
old meaning (select the symbol if its dependencies are met) nor the new
meaning (enable it by default, but let the user set any other setting)
is what we want here.
Work around this by adding two more Kconfig options that lead to
the correct behavior: if DRM_RCAR_USE_CMM and DRM_RCAR_USE_LVDS
are enabled, that portion of the driver becomes usable, and no
configuration results in a link error.
This avoids a link failure:
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_crtc.o: in function `rcar_du_crtc_atomic_begin':
rcar_du_crtc.c:(.text+0x1444): undefined reference to `rcar_cmm_setup'
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_crtc.o: in function `rcar_du_crtc_atomic_enable':
rcar_du_crtc.c:(.text+0x14d4): undefined reference to `rcar_cmm_enable'
arm-linux-gnueabi-ld: rcar_du_crtc.c:(.text+0x1548): undefined reference to `rcar_cmm_setup'
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_crtc.o: in function `rcar_du_crtc_atomic_disable':
rcar_du_crtc.c:(.text+0x18b8): undefined reference to `rcar_cmm_disable'
arm-linux-gnueabi-ld: drivers/gpu/drm/rcar-du/rcar_du_kms.o: in function `rcar_du_modeset_init':
FIELD_GET() must only be used with a mask that is a compile-time
constant:
drivers/media/platform/ti-vpe/cal.h: In function 'cal_read_field':
include/linux/compiler_types.h:320:38: error: call to '__compiletime_assert_247' declared with attribute error: FIELD_GET: mask is not constant
include/linux/bitfield.h:46:3: note: in expansion of macro 'BUILD_BUG_ON_MSG'
46 | BUILD_BUG_ON_MSG(!__builtin_constant_p(_mask), \
| ^~~~~~~~~~~~~~~~
drivers/media/platform/ti-vpe/cal.h:220:9: note: in expansion of macro 'FIELD_GET'
220 | return FIELD_GET(mask, cal_read(cal, offset));
| ^~~~~~~~~
The problem here is that the function is not always inlined. Mark it
__always_inline to avoid the problem.
The TIS interrupt handler at least has to read and write the interrupt
status register. In case of SPI both operations result in a call to
tpm_tis_spi_transfer() which uses the bus_lock_mutex of the spi device
and thus must only be called from a sleepable context.
To ensure this request a threaded interrupt handler.
Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com> Tested-by: Michael Niewöhner <linux@mniewoehner.de> Tested-by: Jarkko Sakkinen <jarkko@kernel.org> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when regmap_raw_write() splits the data, it uses the
max_raw_write value defined for the bus. For any bus that includes
the target register address in the max_raw_write value, the chunked
transmission will always exceed the maximum transmission length.
To avoid this problem, subtract the length of the register and the
padding from the maximum transmission.
Commit ac4e97abce9b8 ("scatterlist: sg_set_buf() argument must be in linear
mapping") checks that both the signature and the digest reside in the
linear mapping area.
However, more recently commit ba14a194a434c ("fork: Add generic vmalloced
stack support") made it possible to move the stack in the vmalloc area,
which is not contiguous, and thus not suitable for sg_set_buf() which needs
adjacent pages.
Always make a copy of the signature and digest in the same buffer used to
store the key and its parameters, and pass them to sg_init_one(). Prefer it
to conditionally doing the copy if necessary, to keep the code simple. The
buffer allocated with kmalloc() is in the linear mapping area.
Increment vcpu->stat.exits when handling a fastpath VM-Exit without
going through any part of the "slow" path. Not bumping the exits stat
can result in wildly misleading exit counts, e.g. if the primary reason
the guest is exiting is to program the TSC deadline timer.
Note that the size 1024 corresponds to the size of the test firmware
buffer. The actual number of the buffers leaked is around 70-110,
depending on the test run.
The cause of the leak is the following:
request_partial_firmware_into_buf() and request_firmware_into_buf()
provided firmware buffer isn't released on release_firmware(), we
have allocated it and we are responsible for deallocating it manually.
This is introduced in a number of context where previously only
release_firmware() was called, which was insufficient.
Reported-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Fixes: 7feebfa487b92 ("test_firmware: add support for request_firmware_into_buf") Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Dan Carpenter <error27@gmail.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Luis Chamberlain <mcgrof@kernel.org> Cc: Russ Weight <russell.h.weight@intel.com> Cc: Tianfei zhang <tianfei.zhang@intel.com> Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Zhengchao Shao <shaozhengchao@huawei.com> Cc: Colin Ian King <colin.i.king@gmail.com> Cc: linux-kernel@vger.kernel.org Cc: Kees Cook <keescook@chromium.org> Cc: Scott Branden <sbranden@broadcom.com> Cc: Luis R. Rodriguez <mcgrof@kernel.org> Cc: linux-kselftest@vger.kernel.org Cc: stable@vger.kernel.org # v5.4 Signed-off-by: Mirsad Goran Todorovac <mirsad.todorovac@alu.unizg.hr> Link: https://lore.kernel.org/r/20230509084746.48259-3-mirsad.todorovac@alu.unizg.hr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BUG: KASAN: null-ptr-deref in soft_cursor+0x384/0x6b4 drivers/video/fbdev/core/softcursor.c:70
Read of size 16 at addr 0000000000000200 by task kworker/u4:1/12
Treat i_data_sem for ea_inodes as being in their own lockdep class to
avoid lockdep complaints about ext4_setattr's use of inode_lock() on
normal inodes potentially causing lock ordering with i_data_sem on
ea_inodes in ext4_xattr_inode_write(). However, ea_inodes will be
operated on by ext4_setattr(), so this isn't a problem.
An ea_inode stores the value of an extended attribute; it can not have
extended attributes itself, or this will cause recursive nightmares.
Add a check in ext4_iget() to make sure this is the case.
If the ea_inode has been pushed out of the inode cache while there is
still a reference in the mb_cache, the lockdep subclass will not be
set on the inode, which can lead to some lockdep false positives.
Add a new flag, EXT4_IGET_EA_INODE which indicates whether the inode
is expected to have the EA_INODE flag or not. If the flag is not
set/clear as expected, then fail the iget() operation and mark the
file system as corrupted.
This commit also makes the ext4_iget() always perform the
is_bad_inode() check even when the inode is already inode cache. This
allows us to remove the is_bad_inode() check from the callers of
ext4_iget() in the ea_inode code.
Selftests are supposed to run on any kernels, including the old ones not
supporting MPTCP.
A new check is then added to make sure MPTCP is supported. If not, the
test stops and is marked as "skipped". Note that this check can also
mark the test as failed if 'SELFTESTS_MPTCP_LIB_EXPECT_ALL_FEATURES' env
var is set to 1: by doing that, we can make sure a test is not being
skipped by mistake.
A new shared file is added here to be able to re-used the same check in
the different selftests we have.
Link: https://github.com/multipath-tcp/mptcp_net-next/issues/368 Fixes: 048d19d444be ("mptcp: add basic kselftest for mptcp") Cc: stable@vger.kernel.org Acked-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All callers of trace_probe_primary_from_call() check the return
value to be non NULL. However, the function returns
list_first_entry(&tpe->probes, ...) which can never be NULL.
Additionally, it does not check for the list being possibly empty,
possibly causing a type confusion on empty lists.
Use list_first_entry_or_null() which solves both problems.
Link: https://lore.kernel.org/linux-trace-kernel/20230128-list-entry-null-check-v1-1-8bde6a3da2ef@diag.uniroma1.it/ Fixes: 60d53e2c3b75 ("tracing/probe: Split trace_event related data from trace_probe") Signed-off-by: Pietro Borrello <borrello@diag.uniroma1.it> Reviewed-by: Steven Rostedt (Google) <rostedt@goodmis.org> Acked-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Acked-by: Mukesh Ojha <quic_mojha@quicinc.com> Cc: stable@vger.kernel.org Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Linux Kernel currently only requires make v3.82 while the grouped
target functionality requires make v4.3. Removed the grouped target
introduced in 4ce1f694eb5d ("selinux: ensure av_permissions.h is
built when needed") as well as the multiple header file targets in
the make rule. This effectively reverts the problem commit.
We will revisit this change when make >= 4.3 is required by the rest
of the kernel.
Cc: stable@vger.kernel.org Fixes: 4ce1f694eb5d ("selinux: ensure av_permissions.h is built when needed") Reported-by: Erwan Velu <e.velu@criteo.com> Reported-by: Luiz Capitulino <luizcap@amazon.com> Tested-by: Luiz Capitulino <luizcap@amazon.com> Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When compiling on a MIPS 64-bit machine we get these warnings:
In file included from ./arch/mips/include/asm/cacheflush.h:13,
from ./include/linux/cacheflush.h:5,
from ./include/linux/highmem.h:8,
from ./include/linux/bvec.h:10,
from ./include/linux/blk_types.h:10,
from ./include/linux/blkdev.h:9,
from fs/btrfs/disk-io.c:7:
fs/btrfs/disk-io.c: In function ‘csum_tree_block’:
fs/btrfs/disk-io.c:100:34: error: array subscript 1 is above array bounds of ‘struct page *[1]’ [-Werror=array-bounds]
100 | kaddr = page_address(buf->pages[i]);
| ~~~~~~~~~~^~~
./include/linux/mm.h:2135:48: note: in definition of macro ‘page_address’
2135 | #define page_address(page) lowmem_page_address(page)
| ^~~~
cc1: all warnings being treated as errors
We can check if i overflows to solve the problem. However, this doesn't make
much sense, since i == 1 and num_pages == 1 doesn't execute the body of the loop.
In addition, i < num_pages can also ensure that buf->pages[i] will not cross
the boundary. Unfortunately, this doesn't help with the problem observed here:
gcc still complains.
To fix this add a compile-time condition for the extent buffer page
array size limit, which would eventually lead to eliminating the whole
for loop.
CC: stable@vger.kernel.org # 5.10+ Signed-off-by: pengfuyuan <pengfuyuan@kylinos.cn> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
LPUART IP now has two known bugs, one is that CTS has higher priority
than the break signal, which causes the break signal sending through
UARTCTRL_SBK may impacted by the CTS input if the HW flow control is
enabled. It exists on all platforms we support in this driver.
So we add a workaround patch for this issue: commit c4c81db5cf8b
("tty: serial: fsl_lpuart: disable the CTS when send break signal").
Another IP bug is i.MX8QM LPUART may have an additional break character
being sent after SBK was cleared. It may need to add some delay between
clearing SBK and re-enabling CTS to ensure that the SBK latch are
completely cleared.
But we found that during the delay period before CTS is enabled, there
is still a risk that Bluetooth data in TX FIFO may be sent out during
this period because of break off and CTS disabled(even if BT sets CTS
line deasserted, data is still sent to BT).
Due to this risk, we have to drop the CTS-disabling workaround for SBK
bugs, use TXINV seems to be a better way to replace SBK feature and
avoid above risk. Also need to disable the transmitter to prevent any
data from being sent out during break, then invert the TX line to send
break. Then disable the TXINV when turn off break and re-enable
transmitter.
Fixes: c4c81db5cf8b ("tty: serial: fsl_lpuart: disable the CTS when send break signal") Cc: stable <stable@kernel.org> Signed-off-by: Sherry Sun <sherry.sun@nxp.com> Link: https://lore.kernel.org/r/20230519094751.28948-1-sherry.sun@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may get an empty response with zero length at the beginning of
the driver start and get following UBSAN error. Since there is no
content(SDRT_NONE) for the response, just return and skip the response
handling to avoid this problem.
Test pass : SDIO wifi throughput test with this patch
drivers/net/ethernet/sun/cassini.c:1316:29: error: comparison between two arrays [-Werror=array-compare]
drivers/net/ethernet/sun/cassini.c:3783:34: error: comparison between two arrays [-Werror=array-compare]
Note that 2 arrays should be compared by comparing of their addresses:
note: use ‘&cas_prog_workaroundtab[0] == &cas_prog_null[0]’ to compare the addresses
Signed-off-by: Martin Liska <mliska@suse.cz> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the concept of checking for dangling pointers to local variables
at function exit is really interesting, the gcc-12 implementation is not
compatible with reality, and results in false positives.
For example, gcc sees us putting things on a local list head allocated
on the stack, which involves exactly those kinds of pointers to the
local stack entry:
In function ‘__list_add’,
inlined from ‘list_add_tail’ at include/linux/list.h:102:2,
inlined from ‘rebuild_snap_realms’ at fs/ceph/snap.c:434:2:
include/linux/list.h:74:19: warning: storing the address of local variable ‘realm_queue’ in ‘*&realm_27(D)->rebuild_item.prev’ [-Wdangling-pointer=]
74 | new->prev = prev;
| ~~~~~~~~~~^~~~~~
But then gcc - understandably - doesn't really understand the big
picture how the doubly linked list works, so doesn't see how we then end
up emptying said list head in a loop and the pointer we added has been
removed.
Gcc also complains about us (intentionally) using this as a way to store
a kind of fake stack trace, eg
drivers/acpi/acpica/utdebug.c:40:38: warning: storing the address of local variable ‘current_sp’ in ‘acpi_gbl_entry_stack_pointer’ [-Wdangling-pointer=]
40 | acpi_gbl_entry_stack_pointer = ¤t_sp;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
which is entirely reasonable from a compiler standpoint, and we may want
to change those kinds of patterns, but not not.
So this is one of those "it would be lovely if the compiler were to
complain about us leaving dangling pointers to the stack", but not this
way.
In builds with -Warray-bounds, casts from smaller objects to larger
objects will produce warnings. These can be overly conservative, but since
-Warray-bounds has been finding legitimate bugs, it is desirable to turn
it on globally. Instead of casting a u32 to a larger object, redefine
the u32 portion of the header to a separate struct that can be used for
both u32 operations and the distinct header fields. Silences this warning:
drivers/net/wireless/ath/ath6kl/htc_mbox.c: In function 'htc_wait_for_ctrl_msg':
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2275:20: error: array subscript 'struct htc_frame_hdr[0]' is partly outside array bounds of 'u32[1]' {aka 'unsigned int[1]'} [-Werror=array-bounds]
2275 | if (htc_hdr->eid != ENDPOINT_0)
| ^~
drivers/net/wireless/ath/ath6kl/htc_mbox.c:2264:13: note: while referencing 'look_ahead'
2264 | u32 look_ahead;
| ^~~~~~~~~~
This change results in no executable instruction differences.
Address of a field inside a struct can't possibly be null; gcc-12 warns
about this.
Signed-off-by: Adam Borowski <kilobyte@angband.pl> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GCC 11 (incorrectly[1]) assumes that literal values cast to (void *)
should be treated like a NULL pointer with an offset, and raises
diagnostics when doing bounds checking under -Warray-bounds. GCC 12
got "smarter" about finding these:
In function 'rdfs8',
inlined from 'vga_recalc_vertical' at /srv/code/arch/x86/boot/video-mode.c:124:29,
inlined from 'set_mode' at /srv/code/arch/x86/boot/video-mode.c:163:3:
/srv/code/arch/x86/boot/boot.h:114:9: warning: array subscript 0 is outside array bounds of 'u8[0]' {aka 'unsigned char[]'} [-Warray-bounds]
114 | asm volatile("movb %%fs:%1,%0" : "=q" (v) : "m" (*(u8 *)addr));
| ^~~
This has been solved in other places[2] already by using the recently
added absolute_pointer() macro. Do the same here.
For devices not attached to a port multiplier and managed directly by
libata, the device number passed to ata_find_dev() must always be lower
than the maximum number of devices returned by ata_link_max_devices().
That is 1 for SATA devices or 2 for an IDE link with master+slave
devices. This device number is the SCSI device ID which matches these
constraints as the IDs are generated per port and so never exceed the
maximum number of devices for the link being used.
However, for libsas managed devices, SCSI device IDs are assigned per
struct scsi_host, leading to device IDs for SATA devices that can be
well in excess of libata per-link maximum number of devices. This
results in ata_find_dev() to always return NULL for libsas managed
devices except for the first device of the target scsi_host with ID
(device number) equal to 0. This issue is visible by executing the
hdparm utility, which fails. E.g.:
hdparm -i /dev/sdX
/dev/sdX:
HDIO_GET_IDENTITY failed: No message of desired type
Fix this by rewriting ata_find_dev() to ignore the device number for
non-PMP attached devices with a link with at most 1 device, that is SATA
devices. For these, the device number 0 is always used to
return the correct pointer to the struct ata_device of the port link.
This change excludes IDE master/slave setups (maximum number of devices
per link is 2) and port-multiplier attached devices. Also, to be
consistant with the fact that SCSI device IDs and channel numbers used
as device numbers are both unsigned int, change the devno argument of
ata_find_dev() to unsigned int.
Reported-by: Xingui Yang <yangxingui@huawei.com> Fixes: 41bda9c98035 ("libata-link: update hotplug to handle PMP links") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Jason Yan <yanaijie@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc 13 may assign another type to enumeration constants than gcc 12. Split
the large enum at the top of source file stex.c such that the type of the
constants used in time expressions is changed back to the same type chosen
by gcc 12. This patch suppresses compiler warnings like this one:
In file included from ./include/linux/bitops.h:7,
from ./include/linux/kernel.h:22,
from drivers/scsi/stex.c:13:
drivers/scsi/stex.c: In function ‘stex_common_handshake’:
./include/linux/typecheck.h:12:25: error: comparison of distinct pointer types lacks a cast [-Werror]
12 | (void)(&__dummy == &__dummy2); \
| ^~
./include/linux/jiffies.h:106:10: note: in expansion of macro ‘typecheck’
106 | typecheck(unsigned long, b) && \
| ^~~~~~~~~
drivers/scsi/stex.c:1035:29: note: in expansion of macro ‘time_after’
1035 | if (time_after(jiffies, before + MU_MAX_DELAY * HZ)) {
| ^~~~~~~~~~
See also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=107405.
Cc: stable@vger.kernel.org Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested Signed-off-by: Bart Van Assche <bvanassche@acm.org> Link: https://lore.kernel.org/r/20230529195034.3077-1-bvanassche@acm.org Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The channel's rpmsg object allows new invocations to be made. After old
invocations are already interrupted, the driver shouldn't try to invoke
anymore. Invalidating the rpmsg at the end of the driver removal
function makes it easy to cause a race condition in userspace. Even
closing a file descriptor before the driver finishes its cleanup can
cause an invocation via fastrpc_release_current_dsp_process() and
subsequent timeout.
Invalidate the channel before the invocations are interrupted to make
sure that no invocations can be created to hang after the device closes.
Fixes: c68cfb718c8f ("misc: fastrpc: Add support for context Invoke method") Cc: stable <stable@kernel.org> Signed-off-by: Richard Acayan <mailingradian@gmail.com> Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20230523152550.438363-5-srinivas.kandagatla@linaro.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return value is initialized as -1, or -EPERM. The completion of an
invocation implies that the return value is set appropriately, but
"Permission denied" does not accurately describe the outcome of the
invocation. Set the invocation's return value to a more appropriate
"Broken pipe", as the cleanup breaks the driver's connection with rpmsg.
While exercising the unbind path, with the current implementation
the functionfs_unbind would be calling which waits for the ffs->mutex
to be available, however within the same time ffs_ep0_read is invoked
& if no setup packets are pending, it will invoke function
wait_event_interruptible_exclusive_locked_irq which by definition waits
for the ev.count to be increased inside the same mutex for which
functionfs_unbind is waiting.
This creates deadlock situation because the functionfs_unbind won't
get the lock until ev.count is increased which can only happen if
the caller ffs_func_unbind can proceed further.
Commit 28d1a7ac2a0d ("iio: dac: Add AD5758 support") adds the config AD5758
and the corresponding driver ad5758.c. In the Makefile, the ad5758 driver
is however included when AD5755 is selected, not when AD5758 is selected.
Probably, this was simply a mistake that happened by copy-and-paste and
forgetting to adjust the actual line. Surprisingly, no one has ever noticed
that this driver is actually only included when AD5755 is selected and that
the config AD5758 has actually no effect on the build.
The AD7192 provides a specific channel configuration where both negative
and positive inputs are connected to AIN2. This was represented in the
ad7192 driver as a IIO channel with .channel = 2 and .extended_name set
to "shorted".
The problem with this approach, is that the driver provided two IIO
channels with the identifier .channel = 2; one "shorted" and the other
not. This goes against the IIO ABI, as a channel identifier should be
unique.
Address this issue by changing "shorted" channels to being differential
instead, with channel 2 vs. itself, as we're actually measuring AIN2 vs.
itself.
Note that the fix tag is for the commit that moved the driver out of
staging. The bug existed before that, but backporting would become very
complex further down and unlikely to happen.
Fixes: b581f748cce0 ("staging: iio: adc: ad7192: move out of staging") Signed-off-by: Paul Cercueil <paul@crapouillou.net> Co-developed-by: Alisa Roman <alisa.roman@analog.com> Signed-off-by: Alisa Roman <alisa.roman@analog.com> Reviewed-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20230330102100.17590-1-paul@crapouillou.net Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The i2c_master_send() returns number of sent bytes on success,
or negative on error. The suspend/resume callbacks expect zero
on success and non-zero on error. Adapt the return value of the
i2c_master_send() to the expectation of the suspend and resume
callbacks, including proper validation of the return value.
Fixes: 55707294c4eb ("iio: light: Add support for vishay vcnl4035") Signed-off-by: Frank Li <Frank.Li@nxp.com> Link: https://lore.kernel.org/r/20230501143605.1615549-1-Frank.Li@nxp.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Timestamp reset is not done in the correct place. It must be done
before enabling buffer. The reason is that interrupt timestamping
is always happening when the chip is on, even if the
corresponding sensor is off. When the sensor restarts, timestamp
is wrong if you don't do a reset first.
If high bit is set to 1 in ((data[3] & 0x0f << 28), after all arithmetic
operations and integer promotions are done, high bits in
wacom->serial[idx] will be filled with 1s as well.
Avoid this, albeit unlikely, issue by specifying left operand's __u64
type for the right operand.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
the order of three init operation:
1.mxs_lradc_adc_trigger_init
2.iio_triggered_buffer_setup
3.mxs_lradc_adc_hw_init
thus, the order of three cleanup operation should be:
1.mxs_lradc_adc_hw_stop
2.iio_triggered_buffer_cleanup
3.mxs_lradc_adc_trigger_remove
we exchange the order of two cleanup operations,
introducing the following differences:
1.if mxs_lradc_adc_trigger_init fails, returns directly;
2.if trigger_init succeeds but iio_triggered_buffer_setup fails,
goto err_trig and remove the trigger.
In addition, we also reorder the unwind that goes on in the
remove() callback to match the new ordering.
Fixes: 6dd112b9f85e ("iio: adc: mxs-lradc: Add support for ADC driver") Signed-off-by: Jiakai Luo <jkluo@hust.edu.cn> Reviewed-by: Dongliang Mu <dzm91@hust.edu.cn> Link: https://lore.kernel.org/r/20230422133407.72908-1-jkluo@hust.edu.cn Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_PROC_FS is disabled, the function declarations for some
procfs functions are hidden, but the definitions are still build,
as shown by this compiler warning:
net/atm/resources.c:403:7: error: no previous prototype for 'atm_dev_seq_start' [-Werror=missing-prototypes]
net/atm/resources.c:409:6: error: no previous prototype for 'atm_dev_seq_stop' [-Werror=missing-prototypes]
net/atm/resources.c:414:7: error: no previous prototype for 'atm_dev_seq_next' [-Werror=missing-prototypes]
Add another #ifdef to leave these out of the build.
Two functions are defined and used in pcm_oss.c but also optionally
used from io.c, with an optional prototype. If CONFIG_SND_PCM_OSS_PLUGINS
is disabled, this causes a warning as the functions are not static
and have no prototype:
sound/core/oss/pcm_oss.c:1235:19: error: no previous prototype for 'snd_pcm_oss_write3' [-Werror=missing-prototypes]
sound/core/oss/pcm_oss.c:1266:19: error: no previous prototype for 'snd_pcm_oss_read3' [-Werror=missing-prototypes]
Avoid this by making the prototypes unconditional.
gcc with W=1 and ! CONFIG_NF_NAT
net/netfilter/nf_conntrack_netlink.c:3463:32: error:
‘exp_nat_nla_policy’ defined but not used [-Werror=unused-const-variable=]
3463 | static const struct nla_policy exp_nat_nla_policy[CTA_EXPECT_NAT_MAX+1] = {
| ^~~~~~~~~~~~~~~~~~
net/netfilter/nf_conntrack_netlink.c:2979:33: error:
‘any_addr’ defined but not used [-Werror=unused-const-variable=]
2979 | static const union nf_inet_addr any_addr;
| ^~~~~~~~
These variables use is controlled by CONFIG_NF_NAT, so should their definitions.
Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
clang warns about an unpacked structure inside of a packed one:
drivers/net/wireless/broadcom/b43/b43.h:654:4: error: field data within 'struct b43_iv' is less aligned than 'union (unnamed union at /home/arnd/arm-soc/drivers/net/wireless/broadcom/b43/b43.h:651:2)' and is usually due to 'struct b43_iv' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
The problem here is that the anonymous union has the default alignment
from its members, apparently because the original author mixed up the
placement of the __packed attribute by placing it next to the struct
member rather than the union definition. As the struct itself is
also marked as __packed, there is no need to mark its members, so just
move the annotation to the inner type instead.
As Michael noted, the same problem is present in b43legacy, so
change both at the same time.
If scsi_dispatch_cmd() failed, the SCSI command was not sent to the target,
scsi_queue_rq() would return BLK_STS_RESOURCE and the related request would
be requeued. The timeout of this request would not fire, no one would
increase iodone_cnt.
The above flow would result the iodone_cnt smaller than iorequest_cnt. So
decrease the iorequest_cnt if dispatch failed to workaround the issue.
Signed-off-by: Wenchao Hao <haowenchao2@huawei.com> Reported-by: Ming Lei <ming.lei@redhat.com> Closes: https://lore.kernel.org/r/ZF+zB+bB7iqe0wGd@ovpn-8-17.pek2.redhat.com Link: https://lore.kernel.org/r/20230515070156.1790181-3-haowenchao2@huawei.com Reviewed-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When using rtl8192cu with rtl8xxxu driver to connect wifi, there is a
probability of failure, which shows "authentication with ... timed out".
Through debugging, it was found that the RCR register has been inexplicably
modified to an incorrect value, resulting in the nic not being able to
receive authenticated frames.
To fix this problem, add regrcr in rtl8xxxu_priv struct, and store
the RCR value every time the register is written, and use it the next
time the register need to be modified.
Key blobs for the IOCTLs PKEY_KBLOB2PROTK[23] may contain clear key
material. Zeroize the copies of these keys in kernel memory after
creating the protected key.
Reviewed-by: Harald Freudenberger <freude@linux.ibm.com> Signed-off-by: Holger Dengler <dengler@linux.ibm.com> Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using a semaphore in the wait_event*() condition is no good idea.
It hits a kernel WARN_ON() at prepare_to_wait_event() like:
do not call blocking ops when !TASK_RUNNING; state=1 set at
prepare_to_wait_event+0x6d/0x690
For avoiding the potential deadlock, rewrite to an open-coded loop
instead. Unlike the loop in wait_event*(), this uses wait_woken()
after the condition check, hence the task state stays consistent.
A race condition may occur between the .disconnect function, which
is called when the device is disconnected, and the dvb_device_open()
function, which is called when the device node is open()ed.
This results in several types of UAFs.
The root cause of this is that you use the dvb_device_open() function,
which does not implement a conditional statement
that checks 'dvbnet->exit'.
So, add 'remove_mutex` to protect 'dvbnet->exit' and use
locked_dvb_net_open() function to check 'dvbnet->exit'.
The driver will match mostly by DT table (even thought there is regular
ID table) so there is little benefit in of_match_ptr (this also allows
ACPI matching via PRP0001, even though it might not be relevant here).
This also fixes !CONFIG_OF error:
drivers/media/dvb-frontends/mn88443x.c:782:34: error: ‘mn88443x_of_match’ defined but not used [-Werror=unused-const-variable=]
Since dvb_frontend_detach() is not called in ttusb_dec_exit_dvb(),
which is called when the device is disconnected, dvb_frontend_free()
is not finally called.
This causes a memory leak just by repeatedly plugging and
unplugging the device.
Fix this issue by adding dvb_frontend_detach() to ttusb_dec_exit_dvb().
The function of "dvb_ca_en50221_write_data" at source/drivers/media
/dvb-core/dvb_ca_en50221.c is used for two cases.
The first case is for writing APDU data in the function of
"dvb_ca_en50221_io_write" at source/drivers/media/dvb-core/
dvb_ca_en50221.c.
The second case is for writing the host link buf size on the
Command Register in the function of "dvb_ca_en50221_link_init"
at source/drivers/media/dvb-core/dvb_ca_en50221.c.
In the second case, there exists a bug like following.
In the function of the "dvb_ca_en50221_link_init",
after a TV host calculates the host link buf_size,
the TV host writes the calculated host link buf_size on the
Size Register.
Accroding to the en50221 Spec (the page 60 of
https://dvb.org/wp-content/uploads/2020/02/En50221.V1.pdf),
before this writing operation, the "SW(CMDREG_SW)" flag in the
Command Register should be set. We can see this setting operation
in the function of the "dvb_ca_en50221_link_init" like below.
...
if ((ret = ca->pub->write_cam_control(ca->pub, slot,
CTRLIF_COMMAND, IRQEN | CMDREG_SW)) != 0)
return ret;
...
But, after that, the real writing operation is implemented using
the function of the "dvb_ca_en50221_write_data" in the function of
"dvb_ca_en50221_link_init", and the "dvb_ca_en50221_write_data"
includes the function of "ca->pub->write_cam_control",
and the function of the "ca->pub->write_cam_control" in the
function of the "dvb_ca_en50221_wrte_data" does not include
"CMDREG_SW" flag like below.
...
if ((status = ca->pub->write_cam_control(ca->pub, slot,
CTRLIF_COMMAND, IRQEN | CMDREG_HC)) != 0)
...
In the above source code, we can see only the "IRQEN | CMDREG_HC",
but we cannot see the "CMDREG_SW".
The "CMDREG_SW" flag which was set in the function of the
"dvb_ca_en50221_link_init" was rollbacked by the follwoing function
of the "dvb_ca_en50221_write_data".
This is a bug. and this bug causes that the calculated host link buf_size
is not properly written in the CI module.
Through this patch, we fix this bug.
IRQ handler netup_spi_interrupt() takes spinlock spi->lock. The lock
is initialized in netup_spi_init(). However, irq handler is registered
before initializing the lock.
Spinlock dma->lock and i2c->lock suffer from the same problem.
Fix this by registering the irq at the end of probe.
In su3000_read_mac_address, if i2c_transfer fails to execute two
messages, array mac address will not be initialized. Without handling
such error, later in function dvb_usb_adapter_dvb_init, proposed_mac
is accessed before initialization.
Fix this error by returning a negative value if message execution fails.
In digitv_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach digitv_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen. We add
check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In rtl28xxu_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach rtl28xxu_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen.
We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a
("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In ce6230_i2c_master_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach ce6230_i2c_master_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen. We add
check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In ec168_i2c_xfer, msg is controlled by user. When msg[i].buf is null
and msg[i].len is zero, former checks on msg[i].buf would be passed.
If accessing msg[i].buf[0] without sanity check, null pointer deref
would happen. We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()")
In az6027_i2c_xfer, msg is controlled by user. When msg[i].buf is null,
commit 0ed554fd769a ("media: dvb-usb: az6027: fix null-ptr-deref in
az6027_i2c_xfer()") fix the null-ptr-deref bug when msg[i].addr is 0x99.
However, null-ptr-deref also happens when msg[i].addr is 0xd0 and 0xc0.
We add check on msg[i].len to prevent null-ptr-deref.
In dvb_demux.c, some logics exist which compare the expected
continuity counter and the real continuity counter. If they
are not matched each other, both of the expected continuity
counter and the real continuity counter should be printed.
But there exists a bug that the expected continuity counter
is not correctly printed. The expected continuity counter is
replaced with the real countinuity counter + 1 so that
the epected continuity counter is not correclty printed.
This is wrong. This bug is fixed.
Apply a workaround for what appears to be a hardware quirk.
The problem seems to happen when enabling "whole chip power" (bit D7
register R6) for the very first time after the chip receives power. If
either "output" (D4) or "DAC" (D3) aren't powered on at that time,
playback becomes very distorted later on.
This happens on the Google Chameleon v3, as well as on a ZYBO Z7-10:
https://ez.analog.com/audio/f/q-a/543726/solved-ssm2603-right-output-offset-issue/480229
I suspect this happens only when using an external MCLK signal (which
is the case for both of these boards).
Here are some experiments run on a Google Chameleon v3. These were run
in userspace using a wrapper around the i2cset utility:
ssmset() {
i2cset -y 0 0x1a $(($1*2)) $2
}
For each of the following sequences, we apply power to the ssm2603
chip, set the configuration registers R0-R5 and R7-R8, run the selected
sequence, and check for distortions on playback.
ssmset 0x09 0x01 # core
ssmset 0x06 0x1f # chip
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x06 0x1f # chip
ssmset 0x09 0x01 # core
ssmset 0x06 0x07 # out, dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x0f # chip, out
ssmset 0x06 0x07 # dac
NOT OK
ssmset 0x09 0x01 # core
ssmset 0x06 0x17 # chip, dac
ssmset 0x06 0x07 # out
NOT OK
For each of the following sequences, we apply power to the ssm2603
chip, run the selected sequence, issue a reset with R15, configure
R0-R5 and R7-R8, run one of the NOT OK sequences from above, and check
for distortions.
A bunch of TI's codecs have binding schemas which force #sound-dai-cells
to one despite those codecs only having a single DAI. Allow for bindings
with zero DAI cells and deprecate the former non-zero value.
This change ensures that if configured in the policy, the if_id set in
the policy and secpath states match during the inbound policy check.
Without this, there is potential for ambiguity where entries in the
secpath differing by only the if_id could be mismatched.
Notably, this is checked in the outbound direction when resolving
templates to SAs, but not on the inbound path when matching SAs and
policies.
Test: Tested against Android kernel unit tests & CTS Signed-off-by: Benedict Wong <benedictwong@google.com> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On slow CPU (FPGA/QEMU emulated) printing overrun messages from
interrupt handler to uart console may leads to more overrun errors.
So use dev_err_ratelimited to limit the number of error messages.
The debugfs_create_dir function returns ERR_PTR in case of error, and the
only correct way to check if an error occurred is 'IS_ERR' inline function.
This patch will replace the null-comparison with IS_ERR.
On corrupt gfs2 file systems the evict code can try to reference the
journal descriptor structure, jdesc, after it has been freed and set to
NULL. The sequence of events is:
init_journal()
...
fail_jindex:
gfs2_jindex_free(sdp); <------frees journals, sets jdesc = NULL
if (gfs2_holder_initialized(&ji_gh))
gfs2_glock_dq_uninit(&ji_gh);
fail:
iput(sdp->sd_jindex); <--references jdesc in evict_linked_inode
evict()
gfs2_evict_inode()
evict_linked_inode()
ret = gfs2_trans_begin(sdp, 0, sdp->sd_jdesc->jd_blocks);
<------references the now freed/zeroed sd_jdesc pointer.
The call to gfs2_trans_begin is done because the truncate_inode_pages
call can cause gfs2 events that require a transaction, such as removing
journaled data (jdata) blocks from the journal.
This patch fixes the problem by adding a check for sdp->sd_jdesc to
function gfs2_evict_inode. In theory, this should only happen to corrupt
gfs2 file systems, when gfs2 detects the problem, reports it, then tries
to evict all the system inodes it has read in up to that point.
Reported-by: Yang Lan <lanyang0908@gmail.com> Signed-off-by: Bob Peterson <rpeterso@redhat.com> Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adding proper support for V4L2_FIELD_ALTERNATE it was missed that
this field format should trigger an interrupt for each field, not just
for the whole frame. Fix this by marking it as progressive in the
capture setup, which will then select the correct interrupt mode.
Tested on both Gen2 and Gen3 with the result of a doubling of the frame
rate for V4L2_FIELD_ALTERNATE. From a PAL video source the frame rate is
now 50, which is expected for alternate field capture.
When unwind instruction is 0xb2,the subsequent instructions
are uleb128 bytes.
For now,it uses only the first uleb128 byte in code.
For vsp increments of 0x204~0x400,use one uleb128 byte like below:
0xc06a00e4 <unwind_test_work>: 0x80b27fac
Compact model index: 0
0xb2 0x7f vsp = vsp + 1024
0xac pop {r4, r5, r6, r7, r8, r14}
For vsp increments larger than 0x400,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x01 vsp = vsp + 1032
0xac pop {r4, r5, r6, r7, r8, r14}
The unwind works well since the decoded uleb128 byte is also 0x81.
For vsp increments larger than 0x600,use two uleb128 bytes like below:
0xc06a00e4 <unwind_test_work>: @0xc0cc9e0c
Compact model index: 1
0xb2 0x81 0x02 vsp = vsp + 1544
0xac pop {r4, r5, r6, r7, r8, r14}
In this case,the decoded uleb128 result is 0x101(vsp=0x204+(0x101<<2)).
While the uleb128 used in code is 0x81(vsp=0x204+(0x81<<2)).
The unwind aborts at this frame since it gets incorrect vsp.
To fix this,add uleb128 decode to cover all the above case.
Signed-off-by: Haibo Li <haibo.li@mediatek.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the sibling keys check fails before we move keys from one sibling
leaf to another, we are not aborting the transaction - we leave that to
some higher level caller of btrfs_search_slot() (or anything else that
uses it to insert items into a b+tree).
This means that the transaction abort will provide a stack trace that
omits the b+tree modification call chain. So change this to immediately
abort the transaction and therefore get a more useful stack trace that
shows us the call chain in the bt+tree modification code.
It's also important to immediately abort the transaction just in case
some higher level caller is not doing it, as this indicates a very
serious corruption and we should stop the possibility of doing further
damage.
Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a user can make copy_from_user() fail, there is a potential for
UAF/DF due to a lack of locking around the allocation, use and freeing
of the data buffers.
This issue is not theoretical. I managed to author a POC for it:
Add a set of HD Audio PCI IDS, and the HDMI codec vendor IDs for
Glenfly Gpus.
- In default_bdl_pos_adj, set bdl to 128 as Glenfly Gpus have hardware
limitation, need to increase hdac interrupt interval.
- In azx_first_init, enable polling mode for Glenfly Gpu. When the codec
complete the command, it sends interrupt and writes response entries to
memory, howerver, the write requests sometimes are not actually
synchronized to memory when driver handle hdac interrupt on Glenfly Gpus.
If the RIRB status is not updated in the interrupt handler,
azx_rirb_get_response keeps trying to recevie a response from rirb until
1s timeout. Enabling polling mode for Glenfly Gpu can fix the issue.
- In patch_gf_hdmi, set Glenlfy Gpu Codec's no_sticky_stream as it need
driver to do actual clean-ups for the linked codec when switch from one
codec to another.
Doing a 'cat /dev/watchdog0' with menz069_wdt as watchdog0 will result in
a NULL pointer dereference.
This happens because we're passing the wrong pointer to
watchdog_register_device(). Fix this by getting rid of the static
watchdog_device structure and use the one embedded into the driver's
per-instance private data.
marvell_nfc_setup_interface() uses the frequency retrieved from the
clock associated with the nand interface to determine the timings that
will be used. By changing the NAND frequency select without reflecting
this in the clock configuration this means that the timings calculated
don't correctly meet the requirements of the NAND chip. This hasn't been
an issue up to now because of a different bug that was stopping the
timings being updated after they were initially set.
When new timing values are calculated in marvell_nfc_setup_interface()
ensure that they will be applied in marvell_nfc_select_target() by
clearing the selected_chip pointer.
A switch held in reset by default needs to wait longer until we can
reliably detect it.
An issue was observed when testing on the Marvell 88E6393X (Link Street).
The driver failed to detect the switch on some upstarts. Increasing the
wait time after reset deactivation solves this issue.
The updated wait time is now also the same as the wait time in the
mv88e6xxx_hardware_reset function.
Fixes: 7b75e49de424 ("net: dsa: mv88e6xxx: wait after reset deactivation") Signed-off-by: Andreas Svensson <andreas.svensson@axis.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230530145223.1223993-1-andreas.svensson@axis.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we send two TCA_FLOWER_KEY_ENC_OPTS_GENEVE packets and their total
size is 252 bytes(key->enc_opts.len = 252) then
key->enc_opts.len = opt->length = data_len / 4 = 0 when the third
TCA_FLOWER_KEY_ENC_OPTS_GENEVE packet enters fl_set_geneve_opt. This
bypasses the next bounds check and results in an out-of-bounds.
Fixes: 0a6e77784f49 ("net/sched: allow flower to match tunnel options") Signed-off-by: Hangyu Hua <hbh25y@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Reviewed-by: Pieter Jansen van Vuuren <pieter.jansen-van-vuuren@amd.com> Link: https://lore.kernel.org/r/20230531102805.27090-1-hbh25y@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
During driver load it reads embedded_cpu bit from initialization
segment, but the initialization segment is readable only after
initialization bit is cleared.
Move the call to mlx5_read_embedded_cpu() right after initialization bit
cleared.
Syzkaller got the following report:
BUG: KASAN: use-after-free in sk_setup_caps+0x621/0x690 net/core/sock.c:2018
Read of size 8 at addr ffff888027f82780 by task syz-executor276/3255
The function sk_setup_caps (called by ip6_sk_dst_store_flow->
ip6_dst_store) referenced already freed memory as this memory was
freed by parallel task in udpv6_sendmsg->ip6_sk_dst_lookup_flow->
sk_dst_check.
The reason for this race condition is: sk_setup_caps() keeps using
the dst after transferring the ownership to the dst cache.
Found by Linux Verification Center (linuxtesting.org) with syzkaller.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Vladislav Efanov <VEfanov@ispras.ru> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The current code for the length calculation wrongly truncates the reported
length of the groups array, causing an under report of the subscribed
groups. To fix this, use 'BITS_TO_BYTES()' which rounds up the
division by 8.
Fixes: b42be38b2778 ("netlink: add API to retrieve all group memberships") Signed-off-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230529153335.389815-1-pctammela@mojatatu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When use the following command to test:
1)ip link add bond0 type bond
2)ip link set bond0 up
3)tc qdisc add dev bond0 root handle ffff: mq
4)tc qdisc replace dev bond0 parent ffff:fff1 handle ffff: mq
This is because when mq is added for the first time, qdiscs in mq is set
to NULL in mq_attach(). Therefore, when replacing mq after adding mq, we
need to initialize qdiscs in the mq before continuing to graft. Otherwise,
it will couse NULL pointer dereference issue in mq_attach(). And the same
issue will occur in the attach functions of mqprio, taprio and htb.
ffff:fff1 means that the repalce qdisc is ingress. Ingress does not allow
any qdisc to be attached. Therefore, ffff:fff1 is incorrectly used, and
the command should be dropped.
Currently, after creating an ingress (or clsact) Qdisc and grafting it
under TC_H_INGRESS (TC_H_CLSACT), it is possible to graft it again under
e.g. a TBF Qdisc:
$ ip link add ifb0 type ifb
$ tc qdisc add dev ifb0 handle 1: root tbf rate 20kbit buffer 1600 limit 3000
$ tc qdisc add dev ifb0 clsact
$ tc qdisc link dev ifb0 handle ffff: parent 1:1
$ tc qdisc show dev ifb0
qdisc tbf 1: root refcnt 2 rate 20Kbit burst 1600b lat 560.0ms
qdisc clsact ffff: parent ffff:fff1 refcnt 2
^^^^^^^^
clsact's refcount has increased: it is now grafted under both
TC_H_CLSACT and 1:1.
ingress and clsact Qdiscs should only be used under TC_H_INGRESS
(TC_H_CLSACT). Prohibit regrafting them.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: 1f211a1b929c ("net, sched: add clsact qdisc") Tested-by: Pedro Tammela <pctammela@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Vlad Buslov <vladbu@nvidia.com> Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently it is possible to add e.g. an HTB Qdisc under ffff:fff1
(TC_H_INGRESS, TC_H_CLSACT):
$ ip link add name ifb0 type ifb
$ tc qdisc add dev ifb0 parent ffff:fff1 htb
$ tc qdisc add dev ifb0 clsact
Error: Exclusivity flag on, cannot modify.
$ drgn
...
>>> ifb0 = netdev_get_by_name(prog, "ifb0")
>>> qdisc = ifb0.ingress_queue.qdisc_sleeping
>>> print(qdisc.ops.id.string_().decode())
htb
>>> qdisc.flags.value_() # TCQ_F_INGRESS
2
Only allow ingress and clsact Qdiscs under ffff:fff1. Return -EINVAL
for everything else. Make TCQ_F_INGRESS a static flag of ingress and
clsact Qdiscs.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Fixes: 1f211a1b929c ("net, sched: add clsact qdisc") Tested-by: Pedro Tammela <pctammela@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Vlad Buslov <vladbu@nvidia.com> Signed-off-by: Peilin Ye <peilin.ye@bytedance.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log