When FIFO reaches near full state, device will issue pause frame.
If pause slot is enabled(set to 1), in this time, device will issue
pause frame only once. But if pause slot is disabled(set to 0), device
will keep sending pause frames until FIFO reaches near empty state.
When pause slot is disabled, if there is no one to handle receive
packets, device FIFO will reach near full state and keep sending
pause frames. That will impact entire local area network.
This issue can be reproduced in Chromebox (not Chromebook) in
developer mode running a test image (and v5.10 kernel):
1) ping -f $CHROMEBOX (from workstation on same local network)
2) run "powerd_dbus_suspend" from command line on the $CHROMEBOX
3) ping $ROUTER (wait until ping fails from workstation)
Takes about ~20-30 seconds after step 2 for the local network to
stop working.
Fix this issue by enabling pause slot to only send pause frame once
when FIFO reaches near full state.
Fixes: f1bce4ad2f1c ("r8169: add support for RTL8125") Reported-by: Grant Grundler <grundler@chromium.org> Tested-by: Grant Grundler <grundler@chromium.org> Cc: stable@vger.kernel.org Signed-off-by: ChunHao Lin <hau@realtek.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com> Link: https://lore.kernel.org/r/20231129155350.5843-1-hau@realtek.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dev_coredumpm() creates a devcoredump device and adds it
to the core kernel framework which eventually end up
sending uevent to the user space and later creates a
symbolic link to the failed device. An application
running in userspace may be interested in this symbolic
link to get the name of the failed device.
In a issue scenario, once uevent sent to the user space
it start reading '/sys/class/devcoredump/devcdX/failing_device'
to get the actual name of the device which might not been
created and it is in its path of creation.
To fix this, suppress sending uevent till the failing device
symbolic link gets created and send uevent once symbolic
link is created successfully.
In following scenario(diagram), when one thread X running dev_coredumpm()
adds devcd device to the framework which sends uevent notification to
userspace and another thread Y reads this uevent and call to
devcd_data_write() which eventually try to delete the queued timer that
is not initialized/queued yet.
So, debug object reports some warning and in the meantime, timer is
initialized and queued from X path. and from Y path, it gets reinitialized
again and timer->entry.pprev=NULL and try_to_grab_pending() stucks.
To fix this, introduce mutex and a boolean flag to serialize the behaviour.
cpu0(X) cpu1(Y)
dev_coredump() uevent sent to user space
device_add() ======================> user space process Y reads the
uevents writes to devcd fd
which results into writes to
devcd_data_write()
mod_delayed_work()
try_to_grab_pending()
del_timer()
debug_assert_init()
INIT_DELAYED_WORK()
schedule_delayed_work()
debug_object_fixup()
timer_fixup_assert_init()
timer_setup()
do_init_timer()
/*
Above call reinitializes
the timer to
timer->entry.pprev=NULL
and this will be checked
later in timer_pending() call.
*/
timer_pending()
!hlist_unhashed_lockless(&timer->entry)
!h->pprev
/*
del_timer() checks h->pprev and finds
it to be NULL due to which
try_to_grab_pending() stucks.
*/
Deduplication isn't supported on cifs, but cifs doesn't reject it, instead
treating it as extent duplication/cloning. This can cause generic/304 to go
silly and run for hours on end.
Fix cifs to indicate EOPNOTSUPP if REMAP_FILE_DEDUP is set in
->remap_file_range().
Note that it's unclear whether or not commit b073a08016a1 is meant to cause
cifs to return an error if REMAP_FILE_DEDUP.
Fixes: b073a08016a1 ("cifs: fix that return -EINVAL when do dedupe operation") Cc: stable@vger.kernel.org Suggested-by: Dave Chinner <david@fromorbit.com>
cc: Xiaoli Feng <fengxiaoli0714@gmail.com>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Darrick Wong <darrick.wong@oracle.com>
cc: fstests@vger.kernel.org
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org Link: https://lore.kernel.org/r/3876191.1701555260@warthog.procyon.org.uk/ Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As pointed out by many, the disk_super structure is NOT initialized
before it is dereferenced in the function
fs/btrfs/disk-io.c:open_ctree() that this commit adds, so something went
wrong here.
STOP command does not guarantee to wait while busy, but subsequent command
MMC_CMDQ_TASK_MGMT to discard the queue will fail if the card is busy, so
be sure to wait by employing mmc_poll_for_busy().
Fixes: 72a5af554df8 ("mmc: core: Add support for handling CQE requests") Cc: stable@vger.kernel.org Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Avri Altman <avri.altman@wdc.com> Reviewed-by: Christian Loehle <christian.loehle@arm.com> Link: https://lore.kernel.org/r/20231103084720.6886-4-adrian.hunter@intel.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dgpu_disable attribute was not documented, this adds the
required documentation.
Fixes: 98829e84dc67 ("asus-wmi: Add dgpu disable method") Signed-off-by: Luke D. Jones <luke@ljones.dev> Link: https://lore.kernel.org/r/20220812222509.292692-2-luke@ljones.dev Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 1ea0d3b46798 ("platform/x86: asus-wmi: Simplify tablet-mode-switch
handling") unified the asus-wmi tablet-switch handling, but it did not take
into account that the value returned for the kbd_dock_devid WMI method is
inverted where as the other ones are not inverted.
This causes asus-wmi to report an inverted tablet-switch state for devices
which use the kbd_dock_devid, which causes libinput to ignore touchpad
events while the affected T10x model 2-in-1s are docked.
Add inverting of the return value in the kbd_dock_devid case to fix this.
Otherwise set elements can be deactivated twice which will cause a crash.
Reported-by: Xingyuan Mo <hdthky0@gmail.com> Fixes: 3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "NET_DM" generic netlink family notifies drop locations over the
"events" multicast group. This is problematic since by default generic
netlink allows non-root users to listen to these notifications.
Fix by adding a new field to the generic netlink multicast group
structure that when set prevents non-root users or root without the
'CAP_SYS_ADMIN' capability (in the user namespace owning the network
namespace) from joining the group. Set this field for the "events"
group. Use 'CAP_SYS_ADMIN' rather than 'CAP_NET_ADMIN' because of the
nature of the information that is shared over this group.
Note that the capability check in this case will always be performed
against the initial user namespace since the family is not netns aware
and only operates in the initial network namespace.
A new field is added to the structure rather than using the "flags"
field because the existing field uses uAPI flags and it is inappropriate
to add a new uAPI flag for an internal kernel check. In net-next we can
rework the "flags" field to use internal flags and fold the new field
into it. But for now, in order to reduce the amount of changes, add a
new field.
Since the information can only be consumed by root, mark the control
plane operations that start and stop the tracing as root-only using the
'GENL_ADMIN_PERM' flag.
The "psample" generic netlink family notifies sampled packets over the
"packets" multicast group. This is problematic since by default generic
netlink allows non-root users to listen to these notifications.
Fix by marking the group with the 'GENL_UNS_ADMIN_PERM' flag. This will
prevent non-root users or root without the 'CAP_NET_ADMIN' capability
(in the user namespace owning the network namespace) from joining the
group.
Ido Schimmel [Mon, 11 Dec 2023 12:37:38 +0000 (14:37 +0200)]
genetlink: add CAP_NET_ADMIN test for multicast bind
This is a partial backport of upstream commit 4d54cc32112d ("mptcp:
avoid lock_fast usage in accept path"). It is only a partial backport
because the patch in the link below was erroneously squash-merged into
upstream commit 4d54cc32112d ("mptcp: avoid lock_fast usage in accept
path"). Below is the original patch description from Florian Westphal:
"
genetlink sets NL_CFG_F_NONROOT_RECV for its netlink socket so anyone can
subscribe to multicast messages.
rtnetlink doesn't allow this unconditionally, rtnetlink_bind() restricts
bind requests to CAP_NET_ADMIN for a few groups.
This allows to set GENL_UNS_ADMIN_PERM flag on genl mcast groups to
mandate CAP_NET_ADMIN.
This will be used by the upcoming mptcp netlink event facility which
exposes the token (mptcp connection identifier) to userspace.
"
When I added support to allow generic netlink multicast groups to be
restricted to subscribers with CAP_NET_ADMIN I was unaware that a
genl_bind implementation already existed in the past.
It was reverted due to ABBA deadlock:
1. ->netlink_bind gets called with the table lock held.
2. genetlink bind callback is invoked, it grabs the genl lock.
But when a new genl subsystem is (un)registered, these two locks are
taken in reverse order.
One solution would be to revert again and add a comment in genl
referring 1e82a62fec613, "genetlink: remove genl_bind").
This would need a second change in mptcp to not expose the raw token
value anymore, e.g. by hashing the token with a secret key so userspace
can still associate subflow events with the correct mptcp connection.
However, Paolo Abeni reminded me to double-check why the netlink table is
locked in the first place.
I can't find one. netlink_bind() is already called without this lock
when userspace joins a group via NETLINK_ADD_MEMBERSHIP setsockopt.
Same holds for the netlink_unbind operation.
Digging through the history, commit f773608026ee1
("netlink: access nlk groups safely in netlink bind and getname")
expanded the lock scope.
commit 3a20773beeeeade ("net: netlink: cap max groups which will be considered in netlink_bind()")
... removed the nlk->ngroups access that the lock scope
extension was all about.
Reduce the lock scope again and always call ->netlink_bind without
the table lock.
The Fixes tag should be vs. the patch mentioned in the link below,
but that one got squash-merged into the patch that came earlier in the
series.
Fixes: 4d54cc32112d8d ("mptcp: avoid lock_fast usage in accept path") Link: https://lore.kernel.org/mptcp/20210213000001.379332-8-mathew.j.martineau@linux.intel.com/T/#u Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Xin Long <lucien.xin@gmail.com> Cc: Johannes Berg <johannes.berg@intel.com> Cc: Sean Tranchetti <stranche@codeaurora.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
File reference cycles have caused lots of problems for io_uring
in the past, and it still doesn't work exactly right and races with
unix_stream_read_generic(). The safest fix would be to completely
disallow sending io_uring files via sockets via SCM_RIGHT, so there
are no possible cycles invloving registered files and thus rendering
SCM accounting on the io_uring side unnecessary.
vgabios is passed from firmware to kernel on Loongson64 systems.
Sane firmware will keep this pointer in reserved memory space
passed from the firmware but insane firmware keeps it in low
memory before kernel entry that is not reserved.
Previously kernel won't try to allocate memory from low memory
before kernel entry on boot, but after converting to memblock
it will do that.
Fix by resversing those memory on early boot.
Cc: stable@vger.kernel.org Fixes: a94e4f24ec83 ("MIPS: init: Drop boot_mem_map") Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the CMMA state needs to be reset, the no-dat bit also needs to be
reset. Failure to do so could cause issues in the guest, since the
guest expects the bit to be cleared after a reset.
Starting RX DMA on THRI interrupt is too early because TX may not have
finished yet.
This change is inspired by commit 90b8596ac460 ("serial: 8250: Prevent
starting up DMA Rx on THRI interrupt") and fixes DMA issues I had with
an AM62 SoC that is using the 8250 OMAP variant.
Cc: stable@vger.kernel.org Fixes: c26389f998a8 ("serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs") Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com> Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com> Link: https://lore.kernel.org/r/20231101171431.16495-1-rwahl@gmx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes commit 439c7183e5b9 ("serial: 8250: 8250_omap: Disable RX
interrupt after DMA enable") which unfortunately set the
UART_HAS_RHR_IT_DIS bit in the UART_OMAP_IER2 register and never
cleared it.
This device has a silicon bug that makes it report a timeout interrupt
but no data in the FIFO.
The datasheet states the following in the errata section 18.1.4:
"If the host reads the receive FIFO at the same time as a
time-out interrupt condition happens, the host might read 0xCC
(time-out) in the Interrupt Indication Register (IIR), but bit 0
of the Line Status Register (LSR) is not set (means there is no
data in the receive FIFO)."
The errata description seems to indicate it concerns only polled mode of
operation when reading bit 0 of the LSR register. However, tests have
shown and NXP has confirmed that the RXLVL register also yields 0 when
the bug is triggered, and hence the IRQ driven implementation in this
driver is equally affected.
This bug has hit us on production units and when it does, sc16is7xx_irq()
would spin forever because sc16is7xx_port_irq() keeps seeing an
interrupt in the IIR register that is not cleared because the driver
does not call into sc16is7xx_handle_rx() unless the RXLVL register
reports at least one byte in the FIFO.
Fix this by always reading one byte from the FIFO when this condition
is detected in order to clear the interrupt. This approach was
confirmed to be correct by NXP through their support channels.
Tested by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Since there is no guarantee that the memory returned by
dma_alloc_coherent() is associated with a 'struct page', using the
architecture specific phys_to_page() is wrong, but using
virt_to_page() would be as well.
Stop using sg lists altogether and just use the *_single() functions
instead. This also simplifies the code a bit since the scatterlists in
this driver always have only one entry anyway.
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
gc: Add a commit log from the initial thread:
https://lore.kernel.org/lkml/86db0fe5-930d-4cbb-bd7d-03367da38951@app.fastmail.com/
Use consistent names for dma buffers
When typec_altmode_put_partner is called by a plug altmode upon release,
the port altmode the plug belongs to will not remove its reference to the
plug. The check to see if the altmode being released evaluates against the
released altmode's partner instead of the calling altmode itself, so change
adev in typec_altmode_put_partner to properly refer to the altmode being
released.
typec_altmode_set_partner is not run for port altmodes, so also add a check
in typec_altmode_release to prevent typec_altmode_put_partner() calls on
port altmode release.
Fixes: 8a37d87d72f0 ("usb: typec: Bus type for alternate modes") Cc: stable@vger.kernel.org Signed-off-by: RD Babiera <rdbabiera@google.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20231129192349.1773623-2-rdbabiera@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling runtime pm as default for all AMD xHC 1.1 controllers caused
regression. An initial attempt to fix those was done in commit a5d6264b638e
("xhci: Enable RPM on controllers that support low-power states") but new
issues are still seen.
Revert this to get those AMD xHC 1.1 systems working
This patch went to stable an needs to be reverted from there as well.
The commit 89ff3dfac604 ("usb: gadget: f_hid: fix f_hidg lifetime vs
cdev") has introduced a bug that leads to hid device corruption after
the replug operation.
Reverse device managed memory allocation for the report descriptor
to fix the issue.
Tested:
This change was tested on the AMD EthanolX CRB server with the BMC
based on the OpenBMC distribution. The BMC provides KVM functionality
via the USB gadget device:
- before: KVM page refresh results in a broken USB device,
- after: KVM page refresh works without any issues.
If gpio_set_transitory() fails, we should free the GPIO again. Most
notably, the flag FLAG_REQUESTED has previously been set in
gpiod_request_commit(), and should be reset on failure.
To my knowledge, this does not affect any current users, since the
gpio_set_transitory() mainly returns 0 and -ENOTSUPP, which is converted
to 0. However the gpio_set_transitory() function calles the .set_config()
function of the corresponding GPIO chip and there are some GPIO drivers in
which some (unlikely) branches return other values like -EPROBE_DEFER,
and -EINVAL. In these cases, the above mentioned FLAG_REQUESTED would not
be reset, which results in the pin being blocked until the next reboot.
Budimir noted that perf_event_validate_size() only checks the size of
the newly added event, even though the sizes of all existing events
can also change due to not all events having the same read_format.
When we attach the new event, perf_group_attach(), we do re-compute
the size for all events.
Sometimes we want to know an accurate number of samples even if it's
lost. Currenlty PERF_RECORD_LOST is generated for a ring-buffer which
might be shared with other events. So it's hard to know per-event
lost count.
Add event->lost_samples field and PERF_FORMAT_LOST to retrieve it from
userspace.
Original-patch-by: Jiri Olsa <jolsa@redhat.com> Signed-off-by: Namhyung Kim <namhyung@kernel.org> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20220616180623.1358843-1-namhyung@kernel.org
Stable-dep-of: 382c27f4ed28 ("perf: Fix perf_event_validate_size()") Signed-off-by: Sasha Levin <sashal@kernel.org>
When the ring buffer is being resized, it can cause side effects to the
running tracer. For instance, there's a race with irqsoff tracer that
swaps individual per cpu buffers between the main buffer and the snapshot
buffer. The resize operation modifies the main buffer and then the
snapshot buffer. If a swap happens in between those two operations it will
break the tracer.
Simply stop the running tracer before resizing the buffers and enable it
again when finished.
Link: https://lkml.kernel.org/r/20231205220010.748996423@goodmis.org Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Fixes: 3928a8a2d9808 ("ftrace: make work with new ring buffer") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently we can resize trace ringbuffer by writing a value into file
'buffer_size_kb', then by reading the file, we get the value that is
usually what we wrote. However, this value may be not actual size of
trace ring buffer because of the round up when doing resize in kernel,
and the actual size would be more useful.
There's a race where if an event is discarded from the ring buffer and an
interrupt were to happen at that time and insert an event, the time stamp
is still used from the discarded event as an offset. This can screw up the
timings.
If the event is going to be discarded, set the "before_stamp" to zero.
When a new event comes in, it compares the "before_stamp" with the
"write_stamp" and if they are not equal, it will insert an absolute
timestamp. This will prevent the timings from getting out of sync due to
the discarded event.
Link: https://lore.kernel.org/linux-trace-kernel/20231206100244.5130f9b3@gandalf.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Fixes: 6f6be606e763f ("ring-buffer: Force before_stamp and write_stamp to be different on discard") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang static analyzer complains that value stored to 'rets' is never
read.Let 'buf_len = -EOVERFLOW' to make sure we can return '-EOVERFLOW'.
Fixes: 8c8d964ce90f ("mei: move hbuf_depth from the mei device to the hw modules") Signed-off-by: Su Hui <suhui@nfschina.com> Link: https://lore.kernel.org/r/20231120095523.178385-2-suhui@nfschina.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reserved memory for scp had node name "scp_mem_region" and also
without unit-address: change the name to "memory@(address)".
This fixes a unit_address_vs_reg warning.
Fix a unit_address_vs_reg warning for the USB VBUS fixed regulators
by renaming the regulator nodes from regulator@{0,1} to regulator-usb-p0
and regulator-usb-p1.
In some potential instances the reference count on struct packet_sock
could be saturated and cause overflows which gets the kernel a bit
confused. To prevent this, move to a 64-bit atomic reference count on
64-bit architectures to prevent the possibility of this type to overflow.
Because we can not handle saturation, using refcount_t is not possible
in this place. Maybe someday in the future if it changes it could be
used. Also, instead of using plain atomic64_t, use atomic_long_t instead.
32-bit machines tend to be memory-limited (i.e. anything that increases
a reference uses so much memory that you can't actually get to 2**32
references). 32-bit architectures also tend to have serious problems
with 64-bit atomics. Hence, atomic_long_t is the more natural solution.
Reported-by: "The UK's National Cyber Security Centre (NCSC)" <security@ncsc.gov.uk> Co-developed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable@kernel.org Reviewed-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20231201131021.19999-1-daniel@iogearbox.net Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Function trace_buffered_event_disable() is responsible for freeing pages
backing buffered events and this process can run concurrently with
trace_event_buffer_lock_reserve().
The following race is currently possible:
* Function trace_buffered_event_disable() is called on CPU 0. It
increments trace_buffered_event_cnt on each CPU and waits via
synchronize_rcu() for each user of trace_buffered_event to complete.
* After synchronize_rcu() is finished, function
trace_buffered_event_disable() has the exclusive access to
trace_buffered_event. All counters trace_buffered_event_cnt are at 1
and all pointers trace_buffered_event are still valid.
* At this point, on a different CPU 1, the execution reaches
trace_event_buffer_lock_reserve(). The function calls
preempt_disable_notrace() and only now enters an RCU read-side
critical section. The function proceeds and reads a still valid
pointer from trace_buffered_event[CPU1] into the local variable
"entry". However, it doesn't yet read trace_buffered_event_cnt[CPU1]
which happens later.
* Function trace_buffered_event_disable() continues. It frees
trace_buffered_event[CPU1] and decrements
trace_buffered_event_cnt[CPU1] back to 0.
* Function trace_event_buffer_lock_reserve() continues. It reads and
increments trace_buffered_event_cnt[CPU1] from 0 to 1. This makes it
believe that it can use the "entry" that it already obtained but the
pointer is now invalid and any access results in a use-after-free.
Fix the problem by making a second synchronize_rcu() call after all
trace_buffered_event values are set to NULL. This waits on all potential
users in trace_event_buffer_lock_reserve() that still read a previous
pointer from trace_buffered_event.
For instance, it can be triggered by running these two commands in
parallel:
$ while true; do
echo hist:key=id.syscall:val=hitcount > \
/sys/kernel/debug/tracing/events/raw_syscalls/sys_enter/trigger;
done
$ stress-ng --sysinfo $(nproc)
The warning indicates that the current ring_buffer_per_cpu is not in the
committing state. It happens because the active ring_buffer_event
doesn't actually come from the ring_buffer_per_cpu but is allocated from
trace_buffered_event.
The bug is in function trace_buffered_event_disable() where the
following normally happens:
* The code invokes disable_trace_buffered_event() via
smp_call_function_many() and follows it by synchronize_rcu(). This
increments the per-CPU variable trace_buffered_event_cnt on each
target CPU and grants trace_buffered_event_disable() the exclusive
access to the per-CPU variable trace_buffered_event.
* Maintenance is performed on trace_buffered_event, all per-CPU event
buffers get freed.
* The code invokes enable_trace_buffered_event() via
smp_call_function_many(). This decrements trace_buffered_event_cnt and
releases the access to trace_buffered_event.
A problem is that smp_call_function_many() runs a given function on all
target CPUs except on the current one. The following can then occur:
* Task X executing trace_buffered_event_disable() runs on CPU 0.
* The control reaches synchronize_rcu() and the task gets rescheduled on
another CPU 1.
* The RCU synchronization finishes. At this point,
trace_buffered_event_disable() has the exclusive access to all
trace_buffered_event variables except trace_buffered_event[CPU0]
because trace_buffered_event_cnt[CPU0] is never incremented and if the
buffer is currently unused, remains set to 0.
* A different task Y is scheduled on CPU 0 and hits a trace event. The
code in trace_event_buffer_lock_reserve() sees that
trace_buffered_event_cnt[CPU0] is set to 0 and decides the use the
buffer provided by trace_buffered_event[CPU0].
* Task X continues its execution in trace_buffered_event_disable(). The
code incorrectly frees the event buffer pointed by
trace_buffered_event[CPU0] and resets the variable to NULL.
* Task Y writes event data to the now freed buffer and later detects the
created inconsistency.
The issue is observable since commit dea499781a11 ("tracing: Fix warning
in trace_buffered_event_disable()") which moved the call of
trace_buffered_event_disable() in __ftrace_event_enable_disable()
earlier, prior to invoking call->class->reg(.. TRACE_REG_UNREGISTER ..).
The underlying problem in trace_buffered_event_disable() is however
present since the original implementation in commit 0fc1b09ff1ff
("tracing: Use temp buffer when filtering events").
Fix the problem by replacing the two smp_call_function_many() calls with
on_each_cpu_mask() which invokes a given callback on all CPUs.
It use to be that only the top level instance had a snapshot buffer (for
latency tracers like wakeup and irqsoff). When stopping a tracer in an
instance would not disable the snapshot buffer. This could have some
unintended consequences if the irqsoff tracer is enabled.
Consolidate the tracing_start/stop() with tracing_start/stop_tr() so that
all instances behave the same. The tracing_start/stop() functions will
just call their respective tracing_start/stop_tr() with the global_array
passed in.
Link: https://lkml.kernel.org/r/20231205220011.041220035@goodmis.org Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Andrew Morton <akpm@linux-foundation.org> Fixes: 6d9b3fa5e7f6 ("tracing: Move tracing_max_latency into trace_array") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It use to be that only the top level instance had a snapshot buffer (for
latency tracers like wakeup and irqsoff). The update of the ring buffer
size would check if the instance was the top level and if so, it would
also update the snapshot buffer as it needs to be the same as the main
buffer.
Now that lower level instances also has a snapshot buffer, they too need
to update their snapshot buffer sizes when the main buffer is changed,
otherwise the following can be triggered:
All addresses printed by checkstack have an extra incorrect 0 appended at
the end.
This was introduced with commit 677f1410e058 ("scripts/checkstack.pl: don't
display $dre as different entity"): since then the address is taken from
the line which contains the function name, instead of the line which
contains stack consumption. E.g. on s390:
So the used regex which matches spaces and hexadecimal numbers to extract
an address now matches a different substring. Subsequently replacing spaces
with 0 appends a zero at the and, instead of replacing leading spaces.
Fix this by using the proper regex, and simplify the code a bit.
If nilfs2 reads a disk image with corrupted segment usage metadata, and
its segment usage information is marked as an error for the segment at the
write location, nilfs_sufile_set_segment_usage() can trigger WARN_ONs
during log writing.
Segments newly allocated for writing with nilfs_sufile_alloc() will not
have this error flag set, but this unexpected situation will occur if the
segment indexed by either nilfs->ns_segnum or nilfs->ns_nextnum (active
segment) was marked in error.
Fix this issue by inserting a sanity check to treat it as a file system
corruption.
Since error returns are not allowed during the execution phase where
nilfs_sufile_set_segment_usage() is used, this inserts the sanity check
into nilfs_sufile_mark_dirty() which pre-reads the buffer containing the
segment usage record to be updated and sets it up in a dirty state for
writing.
In addition, nilfs_sufile_set_segment_usage() is also called when
canceling log writing and undoing segment usage update, so in order to
avoid issuing the same kernel warning in that case, in case of
cancellation, avoid checking the error flag in
nilfs_sufile_set_segment_usage().
When mounting a filesystem image with a block size larger than the page
size, nilfs2 repeatedly outputs long error messages with stack traces to
the kernel log, such as the following:
This overloads the system logger. And to make matters worse, it sometimes
crashes the kernel with a memory access violation.
This is because the return value of the sb_set_blocksize() call, which
should be checked for errors, is not checked.
The latter issue is due to out-of-buffer memory being accessed based on a
large block size that caused sb_set_blocksize() to fail for buffers read
with the initial minimum block size that remained unupdated in the
super_block structure.
Since nilfs2 mkfs tool does not accept block sizes larger than the system
page size, this has been overlooked. However, it is possible to create
this situation by intentionally modifying the tool or by passing a
filesystem image created on a system with a large page size to a system
with a smaller page size and mounting it.
Fix this issue by inserting the expected error handling for the call to
sb_set_blocksize().
The pcm state can be SNDRV_PCM_STATE_DISCONNECTED at disconnect
callback, and there is not an entry of SNDRV_PCM_STATE_DISCONNECTED
in snd_pcm_state_names.
This patch adds the missing entry to resolve this issue.
cat /proc/asound/card2/pcm0p/sub0/status
That results in stack traces like the following:
The timer nodes declare compatibility with "fsl,imx6sx-gpt", which
itself is compatible with "fsl,imx6dl-gpt". Switch the fallback
compatible from "fsl,imx6sx-gpt" to "fsl,imx6dl-gpt".
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure. Ensure the allocation was successful
by checking the pointer validity.
Release the id allocated in 'mmdc_pmu_init' when 'devm_kasprintf'
return NULL
When an error occurs in the for loop of beiscsi_init_wrb_handle(), we
should free phwi_ctxt->be_wrbq before returning an error code to prevent
potential memleak.
Fixes: a7909b396ba7 ("[SCSI] be2iscsi: Fix dynamic CID allocation Mechanism in driver") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20231123081941.24854-1-dinghao.liu@zju.edu.cn Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function trace_buffered_event_disable() produces an unexpected warning
when the previous call to trace_buffered_event_enable() fails to
allocate pages for buffered events.
The situation can occur as follows:
* The counter trace_buffered_event_ref is at 0.
* The soft mode gets enabled for some event and
trace_buffered_event_enable() is called. The function increments
trace_buffered_event_ref to 1 and starts allocating event pages.
* The allocation fails for some page and trace_buffered_event_disable()
is called for cleanup.
* Function trace_buffered_event_disable() decrements
trace_buffered_event_ref back to 0, recognizes that it was the last
use of buffered events and frees all allocated pages.
* The control goes back to trace_buffered_event_enable() which returns.
The caller of trace_buffered_event_enable() has no information that
the function actually failed.
* Some time later, the soft mode is disabled for the same event.
Function trace_buffered_event_disable() is called. It warns on
"WARN_ON_ONCE(!trace_buffered_event_ref)" and returns.
Buffered events are just an optimization and can handle failures. Make
trace_buffered_event_enable() exit on the first failure and left any
cleanup later to when trace_buffered_event_disable() is called.
When wm_adsp_buffer_read() fails, we should free buf->regions.
Otherwise, the callers of wm_adsp_buffer_populate() will
directly free buf on failure, which makes buf->regions a leaked
memory.
Fixes: a792af69b08f ("ASoC: wm_adsp: Refactor compress stream initialisation") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> Link: https://lore.kernel.org/r/20231204074158.12026-1-dinghao.liu@zju.edu.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
"If an error occurs while obtaining the meter reading or if the value
is not available then an Integer with all bits set is returned"
Since the "integer" is 32 bits in case of the ACPI power meter,
userspace will get a power reading of 2^32 * 1000 miliwatts (~4.29 MW)
in case of such an error. This was discovered due to a lm_sensors
bugreport (https://github.com/lm-sensors/lm-sensors/issues/460).
Fix this by returning -ENODATA instead.
Tested-by: <urbinek@gmail.com> Fixes: de584afa5e18 ("hwmon driver for ACPI 4.0 power meters") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Link: https://lore.kernel.org/r/20231124182747.13956-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As we chain the WR during write request: memory registration,
rdma write, local invalidate, if only the last WR fail to send due
to send queue overrun, the server can send back the reply, while
client mark the req->in_use to false in case of error in rtrs_clt_req
when error out from rtrs_post_rdma_write_sg.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Signed-off-by: Jack Wang <jinpu.wang@ionos.com> Reviewed-by: Md Haris Iqbal <haris.iqbal@ionos.com> Signed-off-by: Grzegorz Prajsner <grzegorz.prajsner@ionos.com> Link: https://lore.kernel.org/r/20231120154146.920486-8-haris.iqbal@ionos.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Expand the reg size for the vdec node to include cache/performance
registers the rkvdec driver writes to. Also add missing clocks to the
related power-domain.
Fixes: cbd7214402ec ("arm64: dts: rockchip: Define the rockchip Video Decoder node on rk3399") Signed-off-by: Alex Bee <knaerzche@gmail.com> Signed-off-by: Jonas Karlman <jonas@kwiboo.se> Link: https://lore.kernel.org/r/20231105233630.3927502-10-jonas@kwiboo.se Signed-off-by: Heiko Stuebner <heiko@sntech.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently supplicant dependent optee device enumeration only registers
devices whenever tee-supplicant is invoked for the first time. But it
forgets to remove devices when tee-supplicant daemon stops running and
closes its context gracefully. This leads to following error for fTPM
driver during reboot/shutdown:
Fix this by adding an attribute for supplicant dependent devices so that
the user-space service can detect and detach supplicant devices before
closing the supplicant:
$ for dev in /sys/bus/tee/devices/*; do if [[ -f "$dev/need_supplicant" && -f "$dev/driver/unbind" ]]; \
then echo $(basename "$dev") > $dev/driver/unbind; fi done
Reported-by: Jan Kiszka <jan.kiszka@siemens.com> Closes: https://github.com/OP-TEE/optee_os/issues/6094 Fixes: 5f178bb71e3a ("optee: enable support for multi-stage bus enumeration") Signed-off-by: Sumit Garg <sumit.garg@linaro.org> Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Acked-by: Jerome Forissier <jerome.forissier@linaro.org>
[jw: fixed up Date documentation] Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch is based on a detailed report and ideas from Yepeng Pan
and Christian Rossow.
ACK seq validation is currently following RFC 5961 5.2 guidelines:
The ACK value is considered acceptable only if
it is in the range of ((SND.UNA - MAX.SND.WND) <= SEG.ACK <=
SND.NXT). All incoming segments whose ACK value doesn't satisfy the
above condition MUST be discarded and an ACK sent back. It needs to
be noted that RFC 793 on page 72 (fifth check) says: "If the ACK is a
duplicate (SEG.ACK < SND.UNA), it can be ignored. If the ACK
acknowledges something not yet sent (SEG.ACK > SND.NXT) then send an
ACK, drop the segment, and return". The "ignored" above implies that
the processing of the incoming data segment continues, which means
the ACK value is treated as acceptable. This mitigation makes the
ACK check more stringent since any ACK < SND.UNA wouldn't be
accepted, instead only ACKs that are in the range ((SND.UNA -
MAX.SND.WND) <= SEG.ACK <= SND.NXT) get through.
This can be refined for new (and possibly spoofed) flows,
by not accepting ACK for bytes that were never sent.
This greatly improves TCP security at a little cost.
I added a Fixes: tag to make sure this patch will reach stable trees,
even if the 'blamed' patch was adhering to the RFC.
tp->bytes_acked was added in linux-4.2
Following packetdrill test (courtesy of Yepeng Pan) shows
the issue at hand:
// when window scale is set to 14 the window size can be extended to
// 65535 * (2^14) = 1073725440. Linux would accept an ACK packet
// with ack number in (Server_ISN+1-1073725440. Server_ISN+1)
// ,though this ack number acknowledges some data never
// sent by the server.
// For the established connection, we send an ACK packet,
// the ack packet uses ack number 1 - 1073725300 + 2^32,
// where 2^32 is used to wrap around.
// Note: we used 1073725300 instead of 1073725440 to avoid possible
// edge cases.
// 1 - 1073725300 + 2^32 = 3221241997
// Oops, old kernels happily accept this packet.
+0 < . 1:1001(1000) ack 3221241997 win 65535
// After the kernel fix the following will be replaced by a challenge ACK,
// and prior malicious frame would be dropped.
+0 > . 1:1(0) ack 1001
Fixes: 354e4aa391ed ("tcp: RFC 5961 5.2 Blind Data Injection Attack Mitigation") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Yepeng Pan <yepeng.pan@cispa.de> Reported-by: Christian Rossow <rossow@cispa.de> Acked-by: Neal Cardwell <ncardwell@google.com> Link: https://lore.kernel.org/r/20231205161841.2702925-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
A concurrently running sock_orphan() may NULL the sk_socket pointer in
between check and deref. Follow other users (like nft_meta.c for
instance) and acquire sk_callback_lock before dereferencing sk_socket.
Fixes: 0265ab44bacc ("[NETFILTER]: merge ipt_owner/ip6t_owner in xt_owner") Reported-by: Jann Horn <jannh@google.com> Signed-off-by: Phil Sutter <phil@nwl.cc> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a xge port just connect with an optical module and no fiber,
it may have a fake link up because there may be interference on
the hardware. This patch adds an anti-shake to avoid the problem.
And the time of anti-shake is base on tests.
Fixes: b917078c1c10 ("net: hns: Add ACPI support to check SFP present") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In ipgre_xmit(), skb_pull() may fail even if pskb_inet_may_pull() returns
true. For example, applications can use PF_PACKET to create a malformed
packet with no IP header. This type of packet causes a problem such as
uninit-value access.
This patch ensures that skb_pull() can pull the required size by checking
the skb with pskb_network_may_pull() before skb_pull().
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Suman Ghosh <sumang@marvell.com> Link: https://lore.kernel.org/r/20231202161441.221135-1-syoshida@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently ionic_dim_work() is incorrect when in
split interrupt mode. This is because the interrupt
rate is only being changed for the Rx side even for
dim running on Tx. Fix this by using the qcq from
the container_of macro. Also, introduce some local
variables for a bit of cleanup.
Our friendly kernel test robot has reminded us that with a new
check we have a warning about a potential string truncation.
In this case it really doesn't hurt anything, but it is worth
addressing especially since there really is no reason to reserve
so many bytes for our queue names. It seems that cutting the
queue name buffer length in half stops the complaint.
Fixes: c06107cabea3 ("ionic: more ionic name tweaks") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202311300201.lO8v7mKU-lkp@intel.com/ Signed-off-by: Shannon Nelson <shannon.nelson@amd.com> Reviewed-by: Brett Creeley <brett.creeley@amd.com> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20231204192234.21017-2-shannon.nelson@amd.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When flow_indr_dev_register() fails, bnxt_init_tc will free
bp->tc_info through kfree(). However, the caller function
bnxt_init_one() will ignore this failure and call
bnxt_shutdown_tc() on failure of bnxt_dl_register(), where
a use-after-free happens. Fix this issue by setting
bp->tc_info to NULL after kfree().
Fixes: 627c89d00fb9 ("bnxt_en: flow_offload: offload tunnel decap rules via indirect callbacks") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com> Link: https://lore.kernel.org/r/20231204024004.8245-1-dinghao.liu@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 3a2c6ced90e1 ("i40e: Add a check to see if MFS is set") added
a warning message that reports unexpected size of port's MFS (max
frame size) value. This message use for the port number local
variable 'i' that is wrong.
In i40e_probe() this 'i' variable is used only to iterate VSIs
to find FDIR VSI:
<code>
...
/* if FDIR VSI was set up, start it now */
for (i = 0; i < pf->num_alloc_vsi; i++) {
if (pf->vsi[i] && pf->vsi[i]->type == I40E_VSI_FDIR) {
i40e_vsi_open(pf->vsi[i]);
break;
}
}
...
</code>
So the warning message use for the port number index of FDIR VSI
if this exists or pf->num_alloc_vsi if not.
Fix the message by using 'pf->hw.port' for the port number.
Fixes: 3a2c6ced90e1 ("i40e: Add a check to see if MFS is set") Signed-off-by: Ivan Vecera <ivecera@redhat.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Probe of Sohard Arcnet cards fails,
if 2 or more cards are installed in a system.
See kernel log:
[ 2.759203] arcnet: arcnet loaded
[ 2.763648] arcnet:com20020: COM20020 chipset support (by David Woodhouse et al.)
[ 2.770585] arcnet:com20020_pci: COM20020 PCI support
[ 2.772295] com20020 0000:02:00.0: enabling device (0000 -> 0003)
[ 2.772354] (unnamed net_device) (uninitialized): PLX-PCI Controls
...
[ 3.071301] com20020 0000:02:00.0 arc0-0 (uninitialized): PCI COM20020: station FFh found at F080h, IRQ 101.
[ 3.071305] com20020 0000:02:00.0 arc0-0 (uninitialized): Using CKP 64 - data rate 2.5 Mb/s
[ 3.071534] com20020 0000:07:00.0: enabling device (0000 -> 0003)
[ 3.071581] (unnamed net_device) (uninitialized): PLX-PCI Controls
...
[ 3.369501] com20020 0000:07:00.0: Led pci:green:tx:0-0 renamed to pci:green:tx:0-0_1 due to name collision
[ 3.369535] com20020 0000:07:00.0: Led pci:red:recon:0-0 renamed to pci:red:recon:0-0_1 due to name collision
[ 3.370586] com20020 0000:07:00.0 arc0-0 (uninitialized): PCI COM20020: station E1h found at C000h, IRQ 35.
[ 3.370589] com20020 0000:07:00.0 arc0-0 (uninitialized): Using CKP 64 - data rate 2.5 Mb/s
[ 3.370608] com20020: probe of 0000:07:00.0 failed with error -5
commit 5ef216c1f848 ("arcnet: com20020-pci: add rotary index support")
changes the device name of all COM20020 based PCI cards,
even if only some cards support this:
snprintf(dev->name, sizeof(dev->name), "arc%d-%d", dev->dev_id, i);
The error happens because all Sohard Arcnet cards would be called arc0-0,
since the Sohard Arcnet cards don't have a PLX rotary coder.
I.e. EAE Arcnet cards have a PLX rotary coder,
which sets the first decimal, ensuring unique devices names.
This patch adds two new card feature flags to indicate
which cards support LEDs and the PLX rotary coder.
For EAE based cards the names still depend on the PLX rotary coder
(untested, since missing EAE hardware).
For Sohard based cards, this patch will result in devices
being called arc0, arc1, ... (tested).
Signed-off-by: Thomas Reichinger <thomas.reichinger@sohard.de> Fixes: 5ef216c1f848 ("arcnet: com20020-pci: add rotary index support") Link: https://lore.kernel.org/r/20231130113503.6812-1-thomas.reichinger@sohard.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are two issues when handling error case in com20020pci_probe()
1. priv might be not initialized yet when calling com20020pci_remove()
from com20020pci_probe(), since the priv is set at the very last but it
can jump to error handling in the middle and priv remains NULL.
2. memory leak - the net device is allocated in alloc_arcdev but not
properly released if error happens in the middle of the big for loop
Signed-off-by: Tong Zhang <ztong0001@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 6b17a597fc2f ("arcnet: restoring support for multiple Sohard Arcnet cards") Signed-off-by: Sasha Levin <sashal@kernel.org>
The secure boot state of the BlueField SoC is represented by two bits:
0 = production state
1 = secure boot enabled
2 = non-secure (secure boot disabled)
3 = RMA state
There is also a single bit to indicate whether production keys or
development keys are being used when secure boot is enabled.
This single bit (specified by MLXBF_BOOTCTL_SB_DEV_MASK) only has
meaning if secure boot state equals 1 (secure boot enabled).
The secure boot states are as follows:
- “GA secured” is when secure boot is enabled with official production keys.
- “Secured (development)” is when secure boot is enabled with development keys.
Without this fix “GA Secured” is displayed on development cards which is
misleading. This patch updates the logic in "lifecycle_state_show()" to
handle the case where the SoC is configured for secure boot and is using
development keys.
Fixes: 79e29cb8fbc5c ("platform/mellanox: Add bootctl driver for Mellanox BlueField Soc") Reviewed-by: Khalil Blaiech <kblaiech@nvidia.com> Signed-off-by: David Thompson <davthompson@nvidia.com> Link: https://lore.kernel.org/r/20231130183515.17214-1-davthompson@nvidia.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 1ce09e899d28 ("hyperv: Add support for setting MAC from within guests") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: K. Y. Srinivasan <kys@microsoft.com> Cc: Wei Liu <wei.liu@kernel.org> Cc: Dexuan Cui <decui@microsoft.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Simon Horman <horms@kernel.org> # build-tested Reviewed-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/20231130055853.19069-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
All the mailbox messages sent to AF needs to be guarded
by mutex lock. Add the missing lock in otx2_get_pauseparam
function.
Fixes: 75f36270990c ("octeontx2-pf: Support to enable/disable pause frames via ethtool") Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Many of the DT kerneldoc comments are lacking a 'Return' section. Let's
add the section in cases we have a description of return values. There's
still some cases where the return values are not documented.
The indentation of the kerneldoc comments affects the output formatting.
Leading tabs in particular don't work, sections need to be indented
under the section header, and several code blocks are reformatted.
drivers/of/base.c:315: warning: Function parameter or member 'cpun' not described in '__of_find_n_match_cpu_property'
drivers/of/base.c:315: warning: Function parameter or member 'prop_name' not described in '__of_find_n_match_cpu_property'
drivers/of/base.c:315: warning: Function parameter or member 'cpu' not described in '__of_find_n_match_cpu_property'
drivers/of/base.c:315: warning: Function parameter or member 'thread' not described in '__of_find_n_match_cpu_property'
drivers/of/base.c:315: warning: expecting prototype for property holds the physical id of the(). Prototype was for __of_find_n_match_cpu_property() instead
drivers/of/base.c:1139: warning: Function parameter or member 'match' not described in 'of_find_matching_node_and_match'
drivers/of/base.c:1779: warning: Function parameter or member 'np' not described in '__of_add_property'
drivers/of/base.c:1779: warning: Function parameter or member 'prop' not described in '__of_add_property'
drivers/of/base.c:1800: warning: Function parameter or member 'np' not described in 'of_add_property'
drivers/of/base.c:1800: warning: Function parameter or member 'prop' not described in 'of_add_property'
drivers/of/base.c:1849: warning: Function parameter or member 'np' not described in 'of_remove_property'
drivers/of/base.c:1849: warning: Function parameter or member 'prop' not described in 'of_remove_property'
drivers/of/base.c:2137: warning: Function parameter or member 'dn' not described in 'of_console_check'
drivers/of/base.c:2137: warning: Function parameter or member 'name' not described in 'of_console_check'
drivers/of/base.c:2137: warning: Function parameter or member 'index' not described in 'of_console_check'
Cc: Rob Herring <robh+dt@kernel.org> Cc: Frank Rowand <frowand.list@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: devicetree@vger.kernel.org Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20210318104036.3175910-5-lee.jones@linaro.org
Stable-dep-of: d79972789d17 ("of: dynamic: Fix of_reconfig_get_state_change() return value documentation") Signed-off-by: Sasha Levin <sashal@kernel.org>
asus-nb-wmi calls i8042_install_filter() in some cases, but it never
calls i8042_remove_filter(). This means that a dangling pointer to
the filter function is left after rmmod leading to crashes.
Fix this by moving the i8042-filter installation to the shared
asus-wmi code and also remove it from the shared code on driver unbind.
Fixes: b5643539b825 ("platform/x86: asus-wmi: Filter buggy scan codes on ASUS Q500A") Cc: Oleksij Rempel <linux@rempel-privat.de> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20231120154235.610808-2-hdegoede@redhat.com Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Simplify tablet-mode-switch handling:
1. The code is the same for all variants, the only difference is the
dev_id and notify event code. Store the dev_id + code in struct asus_wmi
and unify the handling
2. Make the new unified asus_wmi_tablet_mode_get_state() check dev_id has
been set and make it a no-op when not set. This allows calling it
unconditionally at resume/restore time
3. Simplify the tablet_mode_sw module-param handling, this also allows
selecting the new lid-flip-rog type through the module-param.
Add quirk for ASUS ROG X13 Flow 2-in-1 to enable tablet mode with
lid flip (all screen rotations).
Signed-off-by: Luke D. Jones <luke@ljones.dev> Link: https://lore.kernel.org/r/20220813092753.6635-2-luke@ljones.dev Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stable-dep-of: b52cbca22cbf ("platform/x86: asus-wmi: Move i8042 filter install to shared asus-wmi code") Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to multiple types of tablet/lidflip, the existing code for
handling these events is refactored to use an enum for each type.
Signed-off-by: Luke D. Jones <luke@ljones.dev> Link: https://lore.kernel.org/r/20220813092753.6635-1-luke@ljones.dev Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stable-dep-of: b52cbca22cbf ("platform/x86: asus-wmi: Move i8042 filter install to shared asus-wmi code") Signed-off-by: Sasha Levin <sashal@kernel.org>
In Windows the ASUS Armory Crate program can enable or disable the
dGPU via a WMI call. This functions much the same as various Linux
methods in software where the dGPU is removed from the device tree.
However the WMI call saves the state of dGPU (enabled or not) and
this then changes the dGPU visibility in Linux with no way for
Linux users to re-enable it. We expose the WMI method so users can
see and change the dGPU ACPI state.
Signed-off-by: Luke D. Jones <luke@ljones.dev> Link: https://lore.kernel.org/r/20210807023656.25020-3-luke@ljones.dev Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stable-dep-of: b52cbca22cbf ("platform/x86: asus-wmi: Move i8042 filter install to shared asus-wmi code") Signed-off-by: Sasha Levin <sashal@kernel.org>
The Asus TP200s / E205SA 360 degree hinges 2-in-1 supports reporting
SW_TABLET_MODE info through the ASUS_WMI_DEVID_LID_FLIP WMI device-id.
Add a quirk to enable this.
Unfortunately we have been unable to find a reliable way to detect if
and how SW_TABLET_MODE reporting is supported, so we are relying on
DMI quirks for this.
Add a module-option to specify the SW_TABLET_MODE method so that this can
be easily tested without needing to rebuild the kernel.
The UX360CA has a WMI device id 0x00060062, which reports whether the
lid is flipped in tablet mode (1) or in normal laptop mode (0).
Add a quirk (quirk_asus_use_lid_flip_devid) for devices on which this
WMI device should be used to figure out the SW_TABLET_MODE state, as
opposed to the quirk_asus_use_kbd_dock_devid.
Additionally, the device needs to be queried on resume and restore
because the firmware does not generate an event if the laptop is put to
sleep while in tablet mode, flipped to normal mode, and later awoken.
It is assumed other UX360* models have the same WMI device. As such, the
quirk is applied to devices with DMI_MATCH(DMI_PRODUCT_NAME, "UX360").
More devices with this feature need to be tested and added accordingly.
The reason for using an allowlist via the quirk mechanism is that the new
WMI device (0x00060062) is also present on some models which do not have
a 360 degree hinge (at least FX503VD and GL503VD from Hans' DSTS
collection) and therefore its presence cannot be relied on.
Signed-off-by: Samuel Čavoj <samuel@cavoj.net> Cc: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20201020220944.1075530-1-samuel@cavoj.net Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Stable-dep-of: b52cbca22cbf ("platform/x86: asus-wmi: Move i8042 filter install to shared asus-wmi code") Signed-off-by: Sasha Levin <sashal@kernel.org>
The variable "chunk_ptr" should be a pointer pointing
to a struct drm_amdgpu_cs_chunk instead of to a pointer
of that.
Signed-off-by: YuanShang <YuanShang.Mao@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, sym_validate_range() duplicates the range string using
xstrdup(), which is overwritten by a subsequent sym_calc_value() call.
It results in a memory leak.
Instead, only the pointer should be copied.
Below is a test case, with a summary from Valgrind.
[Test Kconfig]
config FOO
int "foo"
range 10 20
[Test .config]
CONFIG_FOO=0
[Before]
LEAK SUMMARY:
definitely lost: 3 bytes in 1 blocks
indirectly lost: 0 bytes in 0 blocks
possibly lost: 0 bytes in 0 blocks
still reachable: 17,465 bytes in 21 blocks
suppressed: 0 bytes in 0 blocks
[After]
LEAK SUMMARY:
definitely lost: 0 bytes in 0 blocks
indirectly lost: 0 bytes in 0 blocks
possibly lost: 0 bytes in 0 blocks
still reachable: 17,462 bytes in 20 blocks
suppressed: 0 bytes in 0 blocks
This change moves [rt]x_dropped counters to tg3_napi so that they can be
updated by a single writer, race-free.
Signed-off-by: Alex Pakhunov <alexey.pakhunov@spacex.com> Signed-off-by: Vincent Wong <vincent.wong2@spacex.com> Reviewed-by: Michael Chan <michael.chan@broadcom.com> Link: https://lore.kernel.org/r/20231113182350.37472-1-alexey.pakhunov@spacex.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Linkui Xiao reported that there's a race condition when ipset swap and destroy is
called, which can lead to crash in add/del/test element operations. Swap then
destroy are usual operations to replace a set with another one in a production
system. The issue can in some cases be reproduced with the script:
Swap replaces hash_ip1 with hash_ip2 and then destroy removes hash_ip2 which
is the original hash_ip1. ip_set_test was called on hash_ip1 and because destroy
removed it, hash_net_kadt crashes.
The fix is to force ip_set_swap() to wait for all readers to finish accessing the
old set pointers by calling synchronize_rcu().
The first version of the patch was written by Linkui Xiao <xiaolinkui@kylinos.cn>.
v2: synchronize_rcu() is moved into ip_set_swap() in order not to burden
ip_set_destroy() unnecessarily when all sets are destroyed.
v3: Florian Westphal pointed out that all netfilter hooks run with rcu_read_lock() held
and em_ipset.c wraps the entire ip_set_test() in rcu read lock/unlock pair.
So there's no need to extend the rcu read locked area in ipset itself.
When running on a many core ARM64 server, errors were
happening in the ISR that looked like corrupted memory. These
corruptions would fix themselves if small delays were inserted
in the ISR. Errors reported by the driver included "i2c_designware
APMC0D0F:00: i2c_dw_xfer_msg: invalid target address" and
"i2c_designware APMC0D0F:00:controller timed out" during
in-band IPMI SSIF stress tests.
The problem was determined to be memory writes in the driver were not
becoming visible to all cores when execution rapidly shifted between
cores, like when a register write immediately triggers an ISR.
Processors with weak memory ordering, like ARM64, make no
guarantees about the order normal memory writes become globally
visible, unless barrier instructions are used to control ordering.
To solve this, regmap accessor functions configured by this driver
were changed to use non-relaxed forms of the low-level register
access functions, which include a barrier on platforms that require
it. This assures memory writes before a controller register access are
visible to all cores. The community concluded defaulting to correct
operation outweighed defaulting to the small performance gains from
using relaxed access functions. Being a low speed device added weight to
this choice of default register access behavior.
Signed-off-by: Jan Bottorff <janb@os.amperecomputing.com> Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com> Tested-by: Serge Semin <fancer.lancer@gmail.com> Reviewed-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
2b8272ff4a70 ("cpu/hotplug: Prevent self deadlock on CPU hot-unplug")
solved the straight forward CPU hotplug deadlock vs. the scheduler
bandwidth timer. Yu discovered a more involved variant where a task which
has a bandwidth timer started on the outgoing CPU holds a lock and then
gets throttled. If the lock required by one of the CPU hotplug callbacks
the hotplug operation deadlocks because the unthrottling timer event is not
handled on the dying CPU and can only be recovered once the control CPU
reaches the hotplug state which pulls the pending hrtimers from the dead
CPU.
Solve this by pushing the hrtimers away from the dying CPU in the dying
callbacks. Nothing can queue a hrtimer on the dying CPU at that point because
all other CPUs spin in stop_machine() with interrupts disabled and once the
operation is finished the CPU is marked offline.
Reported-by: Yu Liao <liaoyu15@huawei.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Liu Tie <liutie4@huawei.com> Link: https://lore.kernel.org/r/87a5rphara.ffs@tglx Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit fixes a bug in commit 9ed9895370ae ("driver core: Functional
dependencies tracking support") where the device link status was
incorrectly updated in the driver unbind path before all the device's
resources were released.
Fixes: 9ed9895370ae ("driver core: Functional dependencies tracking support") Cc: stable <stable@kernel.org> Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Closes: https://lore.kernel.org/all/20231014161721.f4iqyroddkcyoefo@pengutronix.de/ Signed-off-by: Saravana Kannan <saravanak@google.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Mark Brown <broonie@kernel.org> Cc: Matti Vaittinen <mazziesaccount@gmail.com> Cc: James Clark <james.clark@arm.com> Acked-by: "Rafael J. Wysocki" <rafael@kernel.org> Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20231018013851.3303928-1-saravanak@google.com Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log