Due to inconsistencies in the way we manipulate compat GPRs, we have a
few issues today:
* For audit and tracing, where error codes are handled as a (native)
long, negative error codes are expected to be sign-extended to the
native 64-bits, or they may fail to be matched correctly. Thus a
syscall which fails with an error may erroneously be identified as
failing.
* For ptrace, *all* compat return values should be sign-extended for
consistency with 32-bit arm, but we currently only do this for
negative return codes.
* As we may transiently set the upper 32 bits of some compat GPRs while
in the kernel, these can be sampled by perf, which is somewhat
confusing. This means that where a syscall returns a pointer above 2G,
this will be sign-extended, but will not be mistaken for an error as
error codes are constrained to the inclusive range [-4096, -1] where
no user pointer can exist.
To fix all of these, we must consistently use helpers to get/set the
compat GPRs, ensuring that we never write the upper 32 bits of the
return code, and always sign-extend when reading the return code. This
patch does so, with the following changes:
* We re-organise syscall_get_return_value() to always sign-extend for
compat tasks, and reimplement syscall_get_error() atop. We update
syscall_trace_exit() to use syscall_get_return_value().
* We consistently use syscall_set_return_value() to set the return
value, ensureing the upper 32 bits are never set unexpectedly.
* As the core audit code currently uses regs_return_value() rather than
syscall_get_return_value(), we special-case this for
compat_user_mode(regs) such that this will do the right thing. Going
forward, we should try to move the core audit code over to
syscall_get_return_value().
Cc: <stable@vger.kernel.org> Reported-by: He Zhe <zhe.he@windriver.com> Reported-by: weiyuchen <weiyuchen3@huawei.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Will Deacon <will@kernel.org> Reviewed-by: Catalin Marinas <catalin.marinas@arm.com> Link: https://lore.kernel.org/r/20210802104200.21390-1-mark.rutland@arm.com Signed-off-by: Will Deacon <will@kernel.org>
[Mark: trivial conflict resolution for v5.10.y] Signed-off-by: Mark Rutland <mark.rutland@arm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm/amd/display: Only set default brightness for OLED
[Why]
We used to unconditionally set backlight path as AUX for panels capable
of backlight adjustment via DPCD in set default brightness.
[How]
This should be limited to OLED panel only since we control backlight via
PWM path for SDR mode in LCD HDR panel.
Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Camille Cho <Camille.Cho@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes some other code to only use aux for backlight control on
OLED panels. The commit message seems to indicate that PWM should
be used for SDR mode on HDR panels. Do something similar for
backlight control in general. This may need to be revisited if and
when HDR started to get used.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1438
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213715 Reviewed-by: Roman Li <Roman.Li@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Clang detected a problem with rc possibly being unitialized
(when length is zero) in a recently added fallocate code path.
Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When calling the 'ql_wait_for_drvr_lock' and 'ql_adapter_reset', the driver
has already acquired the spin lock, so the driver should not call 'ssleep'
in atomic context.
This bug can be fixed by using 'mdelay' instead of 'ssleep'.
Reported-by: Letu Ren <fantasquex@gmail.com> Signed-off-by: Letu Ren <fantasquex@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This issue was noticed while debugging a shutdown issue where some
secondary CPUs are not being shutdown correctly. A fix for that [1] requires
that secondary cpus be offlined using the cpu_online_mask so that the
stop operation is a no-op if CPU HOTPLUG is disabled. I, like the author in
[1] looked at the architectures and found that alpha is one of two
architectures that executes smp_send_stop() on all possible CPUs.
On alpha, smp_send_stop() sends an IPI to all possible CPUs but only needs
to send them to online CPUs.
Send the stop IPI to only the online CPUs.
[1] https://lkml.org/lkml/2020/1/10/250
Signed-off-by: Prarit Bhargava <prarit@redhat.com> Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Signed-off-by: Matt Turner <mattst88@gmail.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The list_for_each_entry() iterator, "vlan" in this code, can never be
NULL so the warning will never be printed.
Signed-off-by: Harshvardhan Jha <harshvardhan.jha@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add the fake bss just before the connect so that cfg80211_get_bss()
finds the virtual network.
As some code was duplicated, move it in a common function.
While verifying the leaf item that we read from the disk, reiserfs
doesn't check the directory items, this could cause a crash when we
read a directory item from the disk that has an invalid deh_location.
This patch adds a check to the directory items read from the disk that
does a bounds check on deh_location for the directory entries. Any
directory entry header with a directory entry offset greater than the
item length is considered invalid.
This is because 'root_inode' is initialized with wrong mode, and
it's i_op is set to 'reiserfs_special_inode_operations'. Thus add
check for 'root_inode' to fix the problem.
Data transfers are not required to be block aligned in memory, so they
span two pages. Fix this by splitting the call to >sff_data_xfer into
two for that case.
This has been broken since the initial libata import before the damn
of git, but was uncovered by the legacy ide driver removal.
Reported-by: kernel test robot <oliver.sang@intel.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/20210709130237.3730959-1-hch@lst.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Double enqueues in rt runqueues (list) have been reported while running
a simple test that spawns a number of threads doing a short sleep/run
pattern while being concurrently setscheduled between rt and fair class.
__sched_setscheduler() uses rt_effective_prio() to handle proper queuing
of priority boosted tasks that are setscheduled while being boosted.
rt_effective_prio() is however called twice per each
__sched_setscheduler() call: first directly by __sched_setscheduler()
before dequeuing the task and then by __setscheduler() to actually do
the priority change. If the priority of the pi_top_task is concurrently
being changed however, it might happen that the two calls return
different results. If, for example, the first call returned the same rt
priority the task was running at and the second one a fair priority, the
task won't be removed by the rt list (on_list still set) and then
enqueued in the fair runqueue. When eventually setscheduled back to rt
it will be seen as enqueued already and the WARNING/BUG be issued.
Fix this by calling rt_effective_prio() only once and then reusing the
return value. While at it refactor code as well for clarity. Concurrent
priority inheritance handling is still safe and will eventually converge
to a new state by following the inheritance chain(s).
Fixes: 0782e63bc6fe ("sched: Handle priority boosted tasks proper in setscheduler()")
[squashed Peterz changes; added changelog] Reported-by: Mark Simmons <msimmons@redhat.com> Signed-off-by: Juri Lelli <juri.lelli@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20210803104501.38333-1-juri.lelli@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sparse reports a compile time warning when dereferencing an
__iomem pointer:
drivers/soc/ixp4xx/ixp4xx-qmgr.c:149:37: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:153:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:154:40: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:38: warning: dereference of noderef expression
drivers/soc/ixp4xx/ixp4xx-qmgr.c:174:44: warning: dereference of noderef expression
Use __raw_readl() here for consistency with the rest of the file.
This should really get converted to some proper accessor, as the
__raw functions are not meant to be used in drivers, but the driver
has used these since the start, so for the moment, let's only fix
the warning.
Reported-by: kernel test robot <lkp@intel.com> Fixes: d4c9e9fc9751 ("IXP42x: Add QMgr support for IXP425 rev. A0 processors.") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The register offset for SFC_DONE was missing a '0' at the end, causing
us to read from a non-existent register address. We only use this
register in error state dumps so the mistake hasn't caused any real
problems, but fixing it will hopefully make the error state dumps a bit
more useful for debugging.
We currently only enforce BW floors for a subset of nodes in a path.
All BCMs that need updating are queued in the pre_aggregate/aggregate
phase. The first set() commits all queued BCMs and subsequent set()
calls short-circuit without committing anything. Since the floor BW
isn't set in sum_avg/max_peak until set(), then some BCMs are committed
before their associated nodes reflect the floor.
Set the floor as each node is being aggregated. This ensures that all
all relevant floors are set before the BCMs are committed.
Fixes: 266cd33b5913 ("interconnect: qcom: Ensure that the floor bandwidth value is enforced") Signed-off-by: Mike Tipton <mdtipton@codeaurora.org> Link: https://lore.kernel.org/r/20210721175432.2119-4-mdtipton@codeaurora.org
[georgi: Removed unused variable] Signed-off-by: Georgi Djakov <djakov@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pre_aggregate callback isn't called in all cases before calling
aggregate. Add the missing calls so providers can rely on consistent
framework behavior.
Fixes: d3703b3e255f ("interconnect: Aggregate before setting initial bandwidth") Signed-off-by: Mike Tipton <mdtipton@codeaurora.org> Link: https://lore.kernel.org/r/20210721175432.2119-3-mdtipton@codeaurora.org Signed-off-by: Georgi Djakov <djakov@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial BW values may be used by providers to enforce floors. Zero
these values after sync-state so that providers know when to stop
enforcing them.
Fixes: b1d681d8d324 ("interconnect: Add sync state support") Signed-off-by: Mike Tipton <mdtipton@codeaurora.org> Link: https://lore.kernel.org/r/20210721175432.2119-2-mdtipton@codeaurora.org Signed-off-by: Georgi Djakov <djakov@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In meson_spicc_probe, the error handling code needs to clean up master
by calling spi_master_put, but the remove function does not have this
function call. This will lead to memory leak of spicc->master.
Reported-by: Dongliang Mu <mudongliangabcd@gmail.com> Fixes: 454fa271bc4e("spi: Add Meson SPICC driver") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Link: https://lore.kernel.org/r/20210720100116.1438974-1-mudongliangabcd@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The expression sizeof(**ptr) for the void **ptr is just 1 rather than
the size of a pointer. Fix this by using sizeof(*ptr).
Addresses-Coverity: ("Wrong sizeof argument") Fixes: e145d9a184f2 ("interconnect: Add devm_of_icc_get() as exported API for users") Signed-off-by: Colin Ian King <colin.king@canonical.com> Link: https://lore.kernel.org/r/20210730075408.19945-1-colin.king@canonical.com Signed-off-by: Georgi Djakov <djakov@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When compile-testing with 64-bit resource_size_t, gcc reports an invalid
printk format string:
In file included from include/linux/dma-mapping.h:7,
from drivers/soc/ixp4xx/ixp4xx-npe.c:15:
drivers/soc/ixp4xx/ixp4xx-npe.c: In function 'ixp4xx_npe_probe':
drivers/soc/ixp4xx/ixp4xx-npe.c:694:18: error: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' {aka 'long long unsigned int'} [-Werror=format=]
dev_info(dev, "NPE%d at 0x%08x-0x%08x not available\n",
Use the special %pR format string to print the resources.
We can avoid the expensive ISB instruction after reading the counter in
the vDSO gettime functions by creating a fake address hazard against a
dummy stack read, just like we do inside the kernel.
Take a signed 'long' instead of an 'unsigned long' for the number of
pages to add/subtract to the total number of pages used by the MMU. This
fixes a zero-extension bug on 32-bit kernels that effectively corrupts
the per-cpu counter used by the shrinker.
Per-cpu counters take a signed 64-bit value on both 32-bit and 64-bit
kernels, whereas kvm_mod_used_mmu_pages() takes an unsigned long and thus
an unsigned 32-bit value on 32-bit kernels. As a result, the value used
to adjust the per-cpu counter is zero-extended (unsigned -> signed), not
sign-extended (signed -> signed), and so KVM's intended -1 gets morphed to 4294967295 and effectively corrupts the counter.
This was found by a staggering amount of sheer dumb luck when running
kvm-unit-tests on a 32-bit KVM build. The shrinker just happened to kick
in while running tests and do_shrink_slab() logged an error about trying
to free a negative number of objects. The truly lucky part is that the
kernel just happened to be a slightly stale build, as the shrinker no
longer yells about negative objects as of commit 18bb473e5031 ("mm:
vmscan: shrink deferred objects proportional to priority").
vmscan: shrink_slab: mmu_shrink_scan+0x0/0x210 [kvm] negative objects to delete nr=-858993460
Fixes: bc8a3d8925a8 ("kvm: mmu: Fix overflow on kvm mmu page limit calculation") Cc: stable@vger.kernel.org Cc: Ben Gardon <bgardon@google.com> Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210804214609.1096003-1-seanjc@google.com> Reviewed-by: Jim Mattson <jmattson@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KVM creates a debugfs directory for each VM in order to store statistics
about the virtual machine. The directory name is built from the process
pid and a VM fd. While generally unique, it is possible to keep a
file descriptor alive in a way that causes duplicate directories, which
manifests as these messages:
[ 471.846235] debugfs: Directory '20245-4' with parent 'kvm' already present!
Even though this should not happen in practice, it is more or less
expected in the case of KVM for testcases that call KVM_CREATE_VM and
close the resulting file descriptor repeatedly and in parallel.
When this happens, debugfs_create_dir() returns an error but
kvm_create_vm_debugfs() goes on to allocate stat data structs which are
later leaked. The slow memory leak was spotted by syzkaller, where it
caused OOM reports.
Since the issue only affects debugfs, do a lookup before calling
debugfs_create_dir, so that the message is downgraded and rate-limited.
While at it, ensure kvm->debugfs_dentry is NULL rather than an error
if it is not created. This fixes kvm_destroy_vm_debugfs, which was not
checking IS_ERR_OR_NULL correctly.
Cc: stable@vger.kernel.org Fixes: 536a6f88c49d ("KVM: Create debugfs dir and stat files for each VM") Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru> Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Once an exception has been injected, any side effects related to
the exception (such as setting CR2 or DR6) have been taked place.
Therefore, once KVM sets the VM-entry interruption information
field or the AMD EVENTINJ field, the next VM-entry must deliver that
exception.
Pending interrupts are processed after injected exceptions, so
in theory it would not be a problem to use KVM_INTERRUPT when
an injected exception is present. However, DOSEMU is using
run->ready_for_interrupt_injection to detect interrupt windows
and then using KVM_SET_SREGS/KVM_SET_REGS to inject the
interrupt manually. For this to work, the interrupt window
must be delayed after the completion of the previous event
injection.
Similar to [1], this patch fixes the same bug in raid10. Also cleanup the
comments.
[1] commit 2417b9869b81 ("md/raid1: properly indicate failure when ending
a failed write request") Cc: stable@vger.kernel.org Fixes: 7cee6d4e6035 ("md/raid10: end bio when the device faulty") Signed-off-by: Wei Shuyu <wsy@dogben.com> Acked-by: Guoqing Jiang <jiangguoqing@kylinos.cn> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That splat later went away with commit 81e2073c175b ("genirq: Disable
interrupts for force threaded handlers"), which got backported to
-stable. However, when running an -rt kernel, the splat still
exists. Moreover, quoting Thomas Gleixner [1]
But 3d5bfbd97163 ("gpio: mpc8xxx: change the gpio interrupt flags.")
has nothing to do with that:
"Delete the interrupt IRQF_NO_THREAD flags in order to gpio interrupts
can be threaded to allow high-priority processes to preempt."
This changelog is blatantly wrong. In mainline forced irq threads
have always been invoked with softirqs disabled, which obviously
makes them non-preemptible.
So the patch didn't even do what its commit log said.
Based on this patch from TI v5.4 tree which is based on hwmod data
which are now removed:
| ARM: AM43xx: hwmod: Move RNG to a GP only links table
|
| On non-GP devices the RNG is controlled by the secure-side software,
| like in DRA7xx hwmod we should not control this IP when we are not
| a GP device.
|
| Signed-off-by: Andrew F. Davis <afd@ti.com>
Cc: stable@vger.kernel.org # v5.10+ Signed-off-by: Kevin Hilman <khilman@baylibre.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During the driver loading process, the 'dev' field was not assigned, but
the 'dev' field was referenced in the subsequent 'i82092aa_set_mem_map'
function.
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> CC: <stable@vger.kernel.org>
[linux@dominikbrodowski.net: shorten commit message, add Cc to stable] Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The attribute-translator has to take in mind maxtype, that is
xfrm_link::nla_max. When it is set, attributes are not of xfrm_attr_type_t.
Currently, they can be only XFRMA_SPD_MAX (message XFRM_MSG_NEWSPDINFO),
their UABI is the same for 64/32-bit, so just copy them.
Thanks to YueHaibing for reporting this:
In xfrm_user_rcv_msg_compat() if maxtype is not zero and less than
XFRMA_MAX, nlmsg_parse_deprecated() do not initialize attrs array fully.
xfrm_xlate32() will access uninit 'attrs[i]' while iterating all attrs
array.
xfrm_bydst_resize() calls synchronize_rcu() while holding
hash_resize_mutex. But then on PREEMPT_RT configurations,
xfrm_policy_lookup_bytype() may acquire that mutex while running in an
RCU read side critical section. This results in a deadlock.
In fact the scope of hash_resize_mutex is way beyond the purpose of
xfrm_policy_lookup_bytype() to just fetch a coherent and stable policy
for a given destination/direction, along with other details.
The lower level net->xfrm.xfrm_policy_lock, which among other things
protects per destination/direction references to policy entries, is
enough to serialize and benefit from priority inheritance against the
write side. As a bonus, it makes it officially a per network namespace
synchronization business where a policy table resize on namespace A
shouldn't block a policy lookup on namespace B.
Fixes: 77cc278f7b20 (xfrm: policy: Use sequence counters with associated lock) Cc: stable@vger.kernel.org Cc: Ahmed S. Darwish <a.darwish@linutronix.de> Cc: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Varad Gautam <varad.gautam@suse.com> Cc: Steffen Klassert <steffen.klassert@secunet.com> Cc: Herbert Xu <herbert@gondor.apana.org.au> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot reported KCSAN data races vs. timer_base::timer_running being set to
NULL without holding base::lock in expire_timers().
This looks innocent and most reads are clearly not problematic, but
Frederic identified an issue which is:
int data = 0;
void timer_func(struct timer_list *t)
{
data = 1;
}
CPU 0 CPU 1
------------------------------ --------------------------
base = lock_timer_base(timer, &flags); raw_spin_unlock(&base->lock);
if (base->running_timer != timer) call_timer_fn(timer, fn, baseclk);
ret = detach_if_pending(timer, base, true); base->running_timer = NULL;
raw_spin_unlock_irqrestore(&base->lock, flags); raw_spin_lock(&base->lock);
x = data;
If the timer has previously executed on CPU 1 and then CPU 0 can observe
base->running_timer == NULL and returns, assuming the timer has completed,
but it's not guaranteed on all architectures. The comment for
del_timer_sync() makes that guarantee. Moving the assignment under
base->lock prevents this.
For non-RT kernel it's performance wise completely irrelevant whether the
store happens before or after taking the lock. For an RT kernel moving the
store under the lock requires an extra unlock/lock pair in the case that
there is a waiter for the timer, but that's not the end of the world.
Reported-by: syzbot+aa7c2385d46c5eba0b89@syzkaller.appspotmail.com Reported-by: syzbot+abea4558531bae1ba9fe@syzkaller.appspotmail.com Fixes: 030dcdd197d7 ("timers: Prepare support for PREEMPT_RT") Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Link: https://lore.kernel.org/r/87lfea7gw8.fsf@nanos.tec.linutronix.de Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The performance reporting driver added cpu hotplug
feature but it didn't add pmu migration call in cpu
offline function.
This can create an issue incase the current designated
cpu being used to collect fme pmu data got offline,
as based on current code we are not migrating fme pmu to
new target cpu. Because of that perf will still try to
fetch data from that offline cpu and hence we will not
get counter data.
Patch fixed this issue by adding pmu_migrate_context call
in fme_perf_offline_cpu function.
This attempts to fix a bug found with a serial port card which uses
an MCS9922 chip, one of the 4 models for which MSI-X interrupts are
currently supported. I don't possess such a card, and i'm not
experienced with the serial subsystem, so this patch is based on what
i think i found as a likely reason for failure, based on walking the
user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg
output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003)
[ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2
[ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003)
[ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2
...
[ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
[ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
...
This suggests to me that the serial driver wants to register and share a
MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does
not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the
serial port driver means to share the irq, and this mismatch ends in some
failed irq init?
With this setup, data reception works very unreliable, with dropped data,
already at a transmission rate of only a 16 Bytes chunk every 1/120th of
a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to
mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
Disabling the use of MSI interrupts for the serial port pci card did
fix the reliability problems. The user executed the following sequence
of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers
[ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers
[ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2
[ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when
using MSI irq's. Note that all i know for sure is that disabling MSI
irq's fixed the problem for the user, so this patch could be wrong and
is untested. Please review with caution, keeping this in mind.
Elkhart Lake UARTs are PCI enumerated Synopsys DesignWare v4.0+ UART
integrated with Intel iDMA 32-bit DMA controller. There is a specific
driver to handle them, i.e. 8250_lpss. Hence, disable 8250_pci
enumeration for these UARTs.
Fixes: 1b91d97c66ef ("serial: 8250_lpss: Add ->setup() for Elkhart Lake ports") Fixes: 4f912b898dc2 ("serial: 8250_lpss: Enable HS UART on Elkhart Lake") Cc: stable <stable@vger.kernel.org> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20210713101739.36962-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct big-endian accesses to the CBUS UART, a Malta on-board discrete
TI16C550C part wired directly to the system controller's device bus, and
do not use byte swapping with the 32-bit accesses to the device.
The CBUS is used for devices such as the boot flash memory needed early
on in system bootstrap even before PCI has been initialised. Therefore
it uses the system controller's device bus, which follows the endianness
set with the CPU, which means no byte-swapping is ever required for data
accesses to CBUS, unlike with PCI.
The CBUS UART uses the UPIO_MEM32 access method, that is the `readl' and
`writel' MMIO accessors, which on the MIPS platform imply byte-swapping
with PCI systems. Consequently the wrong byte lane is accessed with the
big-endian configuration and the UART is not correctly accessed.
As it happens the UPIO_MEM32BE access method makes use of the `ioread32'
and `iowrite32' MMIO accessors, which still use `readl' and `writel'
respectively, however they byte-swap data passed, effectively cancelling
swapping done with the accessors themselves and making it suitable for
the CBUS UART.
Make the CBUS UART switch between UPIO_MEM32 and UPIO_MEM32BE then,
based on the endianness selected. With this change in place the device
is correctly recognised with big-endian Malta at boot, along with the
Super I/O devices behind PCI:
Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
printk: console [ttyS0] enabled
printk: bootconsole [uart8250] disabled
serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A
Fixes: e7c4782f92fc ("[MIPS] Put an end to <asm/serial.h>'s long and annyoing existence") Cc: stable@vger.kernel.org # v2.6.23+ Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260524430.37803@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Cc: stable@vger.kernel.org # v2.6.12+ Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
The Tegra serial driver always prints an error message when enabling the
FIFO for devices that have support for checking the FIFO enable status.
Fix this by displaying the error message, only when an error occurs.
Finally, update the error message to make it clear that enabling the
FIFO failed and display the error code.
Commit b5776e7524af ("ext4: fix potential htree index checksum
corruption) removed a required restart when multiple levels of index
nodes need to be split. Fix this to avoid directory htree corruptions
when using the large_dir feature.
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
The driver uses a zero-length i2c-read request for type detection so
update the control-request code to use usb_sndctrlpipe() in this case.
Note that actually trying to read the i2c register in question does not
work as the register might not exist (e.g. depending on the demodulator)
as reported by Eero Lehtinen <debiangamer2@gmail.com>.
Reported-by: syzbot+faf11bbadc5a372564da@syzkaller.appspotmail.com Reported-by: Eero Lehtinen <debiangamer2@gmail.com> Tested-by: Eero Lehtinen <debiangamer2@gmail.com> Fixes: d0f232e823af ("[media] rtl28xxu: add heuristic to detect chip type") Cc: stable@vger.kernel.org # 4.0 Cc: Antti Palosaari <crope@iki.fi> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_range_map is freed to early, which might cause an oops when
a driver probe fails.
Call trace:
is_free_buddy_page+0xe4/0x1d4
__free_pages+0x2c/0x88
dma_free_contiguous+0x64/0x80
dma_direct_free+0x38/0xb4
dma_free_attrs+0x88/0xa0
dmam_release+0x28/0x34
release_nodes+0x78/0x8c
devres_release_all+0xa8/0x110
really_probe+0x118/0x2d0
__driver_probe_device+0xc8/0xe0
driver_probe_device+0x54/0xec
__driver_attach+0xe0/0xf0
bus_for_each_dev+0x7c/0xc8
driver_attach+0x30/0x3c
bus_add_driver+0x17c/0x1c4
driver_register+0xc0/0xf8
__platform_driver_register+0x34/0x40
...
This issue is introduced by commit d0243bbd5dd3 ("drivers core:
Free dma_range_map when driver probe failed"). It frees
dma_range_map before the call to devres_release_all, which is too
early. The solution is to free dma_range_map only after
devres_release_all.
There was strange error handling logic in case of fw load failure. For
some reason fw loader callback was doing clean up stuff when fw is not
available. I don't see any reason behind doing this. Since this driver
doesn't have EEPROM firmware let's just disconnect it in case of fw load
failure. Doing clean up stuff in 2 different place which can run
concurently is not good idea and syzbot found 2 bugs related to this
strange approach.
So, in this pacth I deleted all clean up code from fw callback and made
a call to device_release_driver() under device_lock(parent) in case of fw
load failure. This approach is more generic and it defend driver from UAF
bugs, since all clean up code is moved to one place.
This patch is preparation for following patch for error handling
refactoring.
flush_scheduled_work() takes (wq_completion)events lock and
it can lead to deadlock when r871xu_dev_remove() is called from workqueue.
To avoid deadlock sutiation we can change flush_scheduled_work() call to
flush_work() call for all possibly scheduled works in this driver,
since next patch adds device_release_driver() in case of fw load failure.
dma-buf backed shared memory cannot be reliably freed and unregistered
during a kexec operation even when tee_shm_free() is called on the shm
from a .shutdown hook. The problem occurs because dma_buf_put() calls
fput() which then uses task_work_add(), with the TWA_RESUME parameter,
to queue tee_shm_release() to be called before the current task returns
to user mode. However, the current task never returns to user mode
before the kexec completes so the memory is never freed nor
unregistered.
Use tee_shm_alloc_kernel_buf() to avoid dma-buf backed shared memory
allocation so that tee_shm_free() can directly call tee_shm_release().
This will ensure that the shm can be freed and unregistered during a
kexec operation.
Fix a hung task issue, seen when booting the kdump kernel, that is
caused by all of the secure world threads being in a permanent suspended
state:
INFO: task swapper/0:1 blocked for more than 120 seconds.
Not tainted 5.4.83 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
swapper/0 D 0 1 0 0x00000028
Call trace:
__switch_to+0xc8/0x118
__schedule+0x2e0/0x700
schedule+0x38/0xb8
schedule_timeout+0x258/0x388
wait_for_completion+0x16c/0x4b8
optee_cq_wait_for_completion+0x28/0xa8
optee_disable_shm_cache+0xb8/0xf8
optee_probe+0x560/0x61c
platform_drv_probe+0x58/0xa8
really_probe+0xe0/0x338
driver_probe_device+0x5c/0xf0
device_driver_attach+0x74/0x80
__driver_attach+0x64/0xe0
bus_for_each_dev+0x84/0xd8
driver_attach+0x30/0x40
bus_add_driver+0x188/0x1e8
driver_register+0x64/0x110
__platform_driver_register+0x54/0x60
optee_driver_init+0x20/0x28
do_one_initcall+0x54/0x24c
kernel_init_freeable+0x1e8/0x2c0
kernel_init+0x18/0x118
ret_from_fork+0x10/0x18
The invoke_fn hook returned OPTEE_SMC_RETURN_ETHREAD_LIMIT, indicating
that the secure world threads were all in a suspended state at the time
of the kernel crash. This intermittently prevented the kdump kernel from
booting, resulting in a failure to collect the kernel dump.
Make kernel dump collection more reliable on systems utilizing OP-TEE by
refusing to load the driver under the kdump kernel.
Adds a new function tee_shm_alloc_kernel_buf() to allocate shared memory
from a kernel driver. This function can later be made more lightweight
by unnecessary dma-buf export.
The shm cache could contain invalid addresses if
optee_disable_shm_cache() was not called from the .shutdown hook of the
previous kernel before a kexec. These addresses could be unmapped or
they could point to mapped but unintended locations in memory.
Clear the shared memory cache, while being careful to not translate the
addresses returned from OPTEE_SMC_DISABLE_SHM_CACHE, during driver
initialization. Once all pre-cache shm objects are removed, proceed with
enabling the cache so that we know that we can handle cached shm objects
with confidence later in the .shutdown hook.
When the function_graph tracer is in use, arch_stack_walk() may unwind
the stack incorrectly, erroneously reporting itself, missing the final
entry which is being traced, and reporting all traced entries between
these off-by-one from where they should be.
When ftrace hooks a function return, the original return address is
saved to the fgraph ret_stack, and the return address in the LR (or the
function's frame record) is replaced with `return_to_handler`.
When arm64's unwinder encounter frames returning to `return_to_handler`,
it finds the associated original return address from the fgraph ret
stack, assuming the most recent `ret_to_hander` entry on the stack
corresponds to the most recent entry in the fgraph ret stack, and so on.
When arch_stack_walk() is used to dump the current task's stack, it
starts from the caller of arch_stack_walk(). However, arch_stack_walk()
can be traced, and so may push an entry on to the fgraph ret stack,
leaving the fgraph ret stack offset by one from the expected position.
This can be seen when dumping the stack via /proc/self/stack, where
enabling the graph tracer results in an unexpected
`stack_trace_save_tsk` entry at the start of the trace, and `el0_svc`
missing form the end of the trace.
This patch fixes this by marking arch_stack_walk() as notrace, as we do
for all other functions on the path to ftrace_graph_get_ret_stack().
While a few helper functions are not marked notrace, their calls/returns
are balanced, and will have no observable effect when examining the
fgraph ret stack.
It is possible for an exeption boundary to cause a similar offset if the
return address of the interrupted context was in the LR. Fixing those
cases will require some more substantial rework, and is left for
subsequent patches.
Cc: <stable@vger.kernel.org> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Madhavan T. Venkataraman <madvenka@linux.microsoft.com> Cc: Mark Brown <broonie@kernel.org> Cc: Will Deacon <will@kernel.org> Reviwed-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20210802164845.45506-3-mark.rutland@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
----> [ delayed here on one CPU (e.g. vcpu preempted by the host) ]
static_call(tp_func_##name)(__data, args); \
} \
} while (0)
It has loaded the tp->funcs of the old callback, so it will try to use the old
data. This can be fixed by adding a RCU sync anywhere in the 1->0->1
transition chain.
On a N->2->1 transition, we need an rcu-sync because you may have a
sequence of 3->2->1 (or 1->2->1) where the element 0 data is unchanged
between 2->1, but was changed from 3->2 (or from 1->2), which may be
observed by the static call. This can be fixed by adding an
unconditional RCU sync in transition 2->1.
Note, this fixes a correctness issue at the cost of adding a tremendous
performance regression to the disabling of tracepoints.
Before this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m0.778s
user 0m0.000s
sys 0m0.061s
After this commit:
# trace-cmd start -e all
# time trace-cmd start -p nop
real 0m10.593s
user 0m0.017s
sys 0m0.259s
A follow up fix will introduce a more lightweight scheme based on RCU
get_state and cond_sync, that will return the performance back to what it
was. As both this change and the lightweight versions are complex on their
own, for bisecting any issues that this may cause, they are kept as two
separate changes.
Link: https://lkml.kernel.org/r/20210805132717.23813-3-mathieu.desnoyers@efficios.com Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/ Cc: stable@vger.kernel.org Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: Stefan Metzmacher <metze@samba.org> Fixes: d25e37d89dd2 ("tracepoint: Optimize using static_call()") Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On transition from 2->1 callees, we should be comparing .data rather
than .func, because the same callback can be registered twice with
different data, and what we care about here is that the data of array
element 0 is unchanged to skip rcu sync.
Link: https://lkml.kernel.org/r/20210805132717.23813-2-mathieu.desnoyers@efficios.com Link: https://lore.kernel.org/io-uring/4ebea8f0-58c9-e571-fd30-0ce4f6f09c70@samba.org/ Cc: stable@vger.kernel.org Cc: Ingo Molnar <mingo@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: "Paul E. McKenney" <paulmck@kernel.org> Cc: Stefan Metzmacher <metze@samba.org> Fixes: 547305a64632 ("tracepoint: Fix out of sync data passing by static caller") Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The event_trace_add_tracer() can fail. In this case, it leads to a crash
in start_creating with below call stack. Handle the error scenario
properly in trace_array_create_dir.
Since the string type can not be the target of the addition / subtraction
operation, it must be rejected. Without this fix, the string type silently
converted to digits.
Link: https://lkml.kernel.org/r/162742654278.290973.1523000673366456634.stgit@devnote2 Cc: stable@vger.kernel.org Fixes: 100719dcef447 ("tracing: Add simple expression support to hist triggers") Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When working on my user space applications, I found a bug in the synthetic
event code where the automated synthetic event field was not matching the
event field calculation it was attached to. Looking deeper into it, it was
because the calculation hist_field was not given a size.
The synthetic event fields are matched to their hist_fields either by
having the field have an identical string type, or if that does not match,
then the size and signed values are used to match the fields.
The problem arose when I tried to match a calculation where the fields
were "unsigned int". My tool created a synthetic event of type "u32". But
it failed to match. The string was:
Adding debugging into the kernel, I found that the size of "diff" was 0.
And since it was given "unsigned int" as a type, the histogram fallback
code used size and signed. The signed matched, but the size of u32 (4) did
not match zero, and the event failed to be created.
This can be worse if the field you want to match is not one of the
acceptable fields for a synthetic event. As event fields can have any type
that is supported in Linux, this can cause an issue. For example, if a
type is an enum. Then there's no way to use that with any calculations.
Have the calculation field simply take on the size of what it is
calculating.
Link: https://lkml.kernel.org/r/20210730171951.59c7743f@oasis.local.home Cc: Tom Zanussi <zanussi@kernel.org> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: stable@vger.kernel.org Fixes: 100719dcef447 ("tracing: Add simple expression support to hist triggers") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 77271ce4b2c0 ("tracing: Add irq, preempt-count and need resched info
to default trace output"), the default trace output format has been changed to:
<idle>-0 [009] d.h. 22420.068695: _raw_spin_lock_irqsave <-hrtimer_interrupt
<idle>-0 [000] ..s. 22420.068695: _nohz_idle_balance <-run_rebalance_domains
<idle>-0 [011] d.h. 22420.068695: account_process_tick <-update_process_times
The draw_functrace.py(introduced in v2.6.28) can't parse the new version format trace_func,
So we need modify draw_functrace.py to adapt the new version trace output format.
Link: https://lkml.kernel.org/r/20210611022107.608787-1-suhui@zeku.com Cc: stable@vger.kernel.org Fixes: 77271ce4b2c0 tracing: Add irq, preempt-count and need resched info to default trace output Signed-off-by: Hui Su <suhui@zeku.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clk_bulk_get_all() allocates an array of struct clk_bulk data for us
(unlike clk_bulk_get()), so we need to free it. Let's use the
clk_bulk_put_all() helper.
kmemleak complains, on an RK3399 Gru/Kevin system:
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
When receiving FRS and Sourcing_Vbus events from low-level drivers, keep
other events which come a bit earlier so that they will not be ignored
in the event handler.
Fixes: 8dc4bd073663 ("usb: typec: tcpm: Add support for Sink Fast Role SWAP(FRS)") Cc: stable <stable@vger.kernel.org> Cc: Badhri Jagan Sridharan <badhri@google.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Reviewed-by: Badhri Jagan Sridharan <badhri@google.com> Signed-off-by: Kyle Tso <kyletso@google.com> Link: https://lore.kernel.org/r/20210803091314.3051302-1-kyletso@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SAMA7G5 suspending ports will cut the access to OHCI registers and
any subsequent access to them will lead to CPU being blocked trying to
access that memory. Same thing happens on resume: if OHCI memory is
accessed before resuming ports the CPU will block on that access. The
OCHI memory is accessed on suspend/resume though
ohci_suspend()/ohci_resume().
The USB HID standard declares mandatory support for GET_IDLE and SET_IDLE
requests for Boot Keyboard. Most hosts can handle their absence, but others
like some old/strange UEFIs and BIOSes consider this a critical error
and refuse to work with f_hid.
This primitive implementation of saving and returning idle is sufficient
to meet the requirements of the standard and these devices.
For delayed status phase, the usb_gadget->state was set
to USB_STATE_ADDRESS and it has never been updated to
USB_STATE_CONFIGURED.
Patch updates the gadget state to correct USB_STATE_CONFIGURED.
As a result of this bug the controller was not able to enter to
Test Mode while using MSC function.
The usb_add_gadget_udc will add a new gadget to the udc class
driver list. Not calling usb_del_gadget_udc in error branch
will result in residual gadget entry in the udc driver list.
We fix it by calling usb_del_gadget_udc to clean it when error
return.
If the device is already in the runtime suspended state, any call to
the pullup routine will issue a runtime resume on the DWC3 core
device. If the USB gadget is disabling the pullup, then avoid having
to issue a runtime resume, as DWC3 gadget has already been
halted/stopped.
This fixes an issue where the following condition occurs:
This leads to a situation where the DWC3 gadget is not properly
stopped, as the runtime resume would have re-enabled EP0 and event
interrupts, and since we avoided the DWC3 gadget suspend, these
resources were never disabled.
The change to restore the autosuspend from the disabled state uses a
wrong check: namely, it should have been the exact comparison of the
quirk_type instead of the bitwise and (&). Otherwise it matches
wrongly with the other quirk types.
Although re-enabling the autosuspend for the already enabled device
shouldn't matter much, it's better to fix the unbalanced call.
The issue on Acer SWIFT SF314-56 is that headset microphone doesn't work.
The following quirk fixed headset microphone issue. The fixup was found by trial and error.
Note that the fixup of SF314-54/55 (ALC256_FIXUP_ACER_HEADSET_MIC) was not successful on my SF314-56.
This use-after-free happens when a fw_priv object has been freed but
hasn't been removed from the pending list (pending_fw_head). The next
time fw_load_sysfs_fallback tries to insert into the list, it ends up
accessing the pending_list member of the previously freed fw_priv.
The root cause here is that all code paths that abort the fw load
don't delete it from the pending list. For example:
To fix this, delete the fw_priv from the list in __fw_set_state() if
the new state is DONE or ABORTED. This way, all aborts will remove
the fw_priv from the list. Accordingly, remove calls to list_del_init
that were being made before calling fw_state_(aborted|done).
Also, in fw_load_sysfs_fallback, don't add the fw_priv to the pending
list if it is already aborted. Instead, just jump out and return early.
Fixes: bcfbd3523f3c ("firmware: fix a double abort case with fw_load_sysfs_fallback") Cc: stable <stable@vger.kernel.org> Reported-by: syzbot+de271708674e2093097b@syzkaller.appspotmail.com Tested-by: syzbot+de271708674e2093097b@syzkaller.appspotmail.com Reviewed-by: Shuah Khan <skhan@linuxfoundation.org> Acked-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Anirudh Rayabharam <mail@anirudhrb.com> Link: https://lore.kernel.org/r/20210728085107.4141-3-mail@anirudhrb.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only motivation for using -EAGAIN in commit 0542ad88fbdd81bb
("firmware loader: Fix _request_firmware_load() return val for fw load
abort") was to distinguish the error from -ENOMEM, and so there is no
real reason in keeping it. -EAGAIN is typically used to tell the
userspace to try something again and in this case re-using the sysfs
loading interface cannot be retried when a timeout happens, so the
return value is also bogus.
-ETIMEDOUT is received when the wait times out and returning that
is much more telling of what the reason for the failure was. So, just
propagate that instead of returning -EAGAIN.
The chip supports high transfer rates, but with the small default buffers
(64 bytes read), some entire blocks are regularly lost. This typically
happens at 1.5 Mbps (which is the default speed on Rockchip devices) when
used as a console to access U-Boot where the output of the "help" command
misses many lines and where "printenv" mangles the environment.
The FTDI driver doesn't suffer at all from this. One difference is that
it uses 512 bytes rx buffers and 256 bytes tx buffers. Adopting these
values completely resolved the issue, even the output of "dmesg" is
reliable. I preferred to leave the Tx value unchanged as it is not
involved in this issue, while a change could increase the risk of
triggering the same issue with other devices having too small buffers.
I verified that it backports well (and works) at least to 5.4. It's of
low importance enough to be dropped where it doesn't trivially apply
anymore.
rcu: INFO: rcu_preempt self-detected stall on CPU
rcu: 1-...!: (2 ticks this GP) idle=d92/1/0x4000000000000000
softirq=25390/25392 fqs=3
(t=12164 jiffies g=31645 q=43226)
rcu: rcu_preempt kthread starved for 12162 jiffies! g31645 f0x0
RCU_GP_WAIT_FQS(5) ->state=0x0 ->cpu=0
rcu: Unless rcu_preempt kthread gets sufficient CPU time,
OOM is now expected behavior.
rcu: RCU grace-period kthread stack dump:
task:rcu_preempt state:R running task
...........
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: unknown status received: -71
usbtmc 3-1:0.0: usb_submit_urb failed: -19
The function usbtmc_interrupt() resubmits urbs when the error status
of an urb is -EPROTO. In systems using the dummy_hcd usb controller
this can result in endless interrupt loops when the usbtmc device is
disconnected from the host system.
Since host controller drivers already try to recover from transmission
errors, there is no need to resubmit the urb or try other solutions
to repair the error situation.
In case of errors the INT pipe just stops to wait for further packets.
Fixes: dbf3e7f654c0 ("Implement an ioctl to support the USMTMC-USB488 READ_STATUS_BYTE operation") Cc: stable@vger.kernel.org Reported-by: syzbot+e2eae5639e7203360018@syzkaller.appspotmail.com Signed-off-by: Qiang.zhang <qiang.zhang@windriver.com> Acked-by: Guido Kiener <guido.kiener@rohde-schwarz.com> Link: https://lore.kernel.org/r/20210723004334.458930-1-qiang.zhang@windriver.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is hitting might_sleep() warning at hci_sock_dev_event() due to
calling lock_sock() with rw spinlock held [1].
It seems that history of this locking problem is a trial and error.
Commit b40df5743ee8 ("[PATCH] bluetooth: fix socket locking in
hci_sock_dev_event()") in 2.6.21-rc4 changed bh_lock_sock() to
lock_sock() as an attempt to fix lockdep warning.
Then, commit 4ce61d1c7a8e ("[BLUETOOTH]: Fix locking in
hci_sock_dev_event().") in 2.6.22-rc2 changed lock_sock() to
local_bh_disable() + bh_lock_sock_nested() as an attempt to fix the
sleep in atomic context warning.
Then, commit 4b5dd696f81b ("Bluetooth: Remove local_bh_disable() from
hci_sock.c") in 3.3-rc1 removed local_bh_disable().
Then, commit e305509e678b ("Bluetooth: use correct lock to prevent UAF
of hdev object") in 5.13-rc5 again changed bh_lock_sock_nested() to
lock_sock() as an attempt to fix CVE-2021-3573.
This difficulty comes from current implementation that
hci_sock_dev_event(HCI_DEV_UNREG) is responsible for dropping all
references from sockets because hci_unregister_dev() immediately
reclaims resources as soon as returning from
hci_sock_dev_event(HCI_DEV_UNREG).
But the history suggests that hci_sock_dev_event(HCI_DEV_UNREG) was not
doing what it should do.
Therefore, instead of trying to detach sockets from device, let's accept
not detaching sockets from device at hci_sock_dev_event(HCI_DEV_UNREG),
by moving actual cleanup of resources from hci_unregister_dev() to
hci_cleanup_dev() which is called by bt_host_release() when all
references to this unregistered device (which is a kobject) are gone.
Since hci_sock_dev_event(HCI_DEV_UNREG) no longer resets
hci_pi(sk)->hdev, we need to check whether this device was unregistered
and return an error based on HCI_UNREGISTER flag. There might be subtle
behavioral difference in "monitor the hdev" functionality; please report
if you found something went wrong due to this patch.
Link: https://syzkaller.appspot.com/bug?extid=a5df189917e79d5e59c9 Reported-by: syzbot <syzbot+a5df189917e79d5e59c9@syzkaller.appspotmail.com> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Fixes: e305509e678b ("Bluetooth: use correct lock to prevent UAF of hdev object") Acked-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If queue is dying while iolatency_set_limit() is in progress,
blk_get_queue() won't increment the refcount of the queue. However,
blk_put_queue() will still decrement the refcount later, which will
cause the refcout to be unbalanced.
Thus error out in such case to fix the problem.
Fixes: 8c772a9bfc7c ("blk-iolatency: fix IO hang due to negative inflight counter") Signed-off-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Tejun Heo <tj@kernel.org> Link: https://lore.kernel.org/r/20210805124645.543797-1-yukuai3@huawei.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch says:
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3518 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
drivers/net/ethernet/neterion/vxge/vxge-main.c:3520 vxge_device_unregister() error: Using vdev after free_{netdev,candev}(dev);
Since vdev pointer is netdev private data accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Fixes: 6cca200362b4 ("vxge: cleanup probe error paths") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Syzbot reported uninit value pegasus_probe(). The problem was in missing
error handling.
get_interrupt_interval() internally calls read_eprom_word() which can
fail in some cases. For example: failed to receive usb control message.
These cases should be handled to prevent uninit value bug, since
read_eprom_word() will not initialize passed stack variable in case of
internal failure.
Set the error code if bnx2x_alloc_fw_stats_mem() fails. The current
code returns success.
Fixes: ad5afc89365e ("bnx2x: Separate VF and PF logic") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When cross compiling a MIPS kernel on a BSD based HOSTCC leads
to errors like
SYNC include/config/auto.conf.cmd - due to: .config
egrep: empty (sub)expression
UPD include/config/kernel.release
HOSTCC scripts/dtc/dtc.o - due to target missing
It turns out that egrep uses this egrep pattern:
(|MINOR_|PATCHLEVEL_)
This is not valid syntax or gives undefined results according
to POSIX 9.5.3 ERE Grammar
It seems to be silently accepted by the Linux egrep implementation
while a BSD host complains.
Such patterns can be replaced by a transformation like
"(|p1|p2)" -> "(p1|p2)?"
Fixes: 48c35b2d245f ("[MIPS] There is no __GNUC_MAJOR__") Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
According to comment in qdisc_alloc(), sch->seqlock's lockdep
class key should be set to qdisc_tx_busylock, due to possible
type error, sch->busylock's lockdep class key is set to
qdisc_tx_busylock, which is duplicated because sch->busylock's
lockdep class key is already set in qdisc_alloc().
So fix it by replacing sch->busylock with sch->seqlock.
Fixes: 96009c7d500e ("sched: replace __QDISC_STATE_RUNNING bit with a spin lock") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case of this switch we work with 32bit registers on top of 16bit
bus. Some registers (for example access to forwarding database) have
trigger bit on the first 16bit half of request and the result +
configuration of request in the second half. Without this patch, we would
trigger database operation and overwrite result in one run.
To make it work properly, we should do the second part of transfer
before the first one is done.
So far, this rule seems to work for all registers on this switch.
Fixes: ec6698c272de ("net: dsa: add support for Atheros AR9331 built-in switch") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20210803063746.3600-1-o.rempel@pengutronix.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The patch fixing the returned value of ip6_skb_dst_mtu (int -> unsigned
int) was rebased between its initial review and the version applied. In
the meantime fade56410c22 was applied, which added a new variable (int)
used as the returned value. This lead to a mismatch between the function
prototype and the variable used as the return value.
Fixes: 40fc3054b458 ("net: ipv6: fix return value of ip6_skb_dst_mtu") Cc: Vadim Fedorenko <vfedorenko@novek.ru> Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Pauseframe control is set to symmetric mode by default on the NFP.
Pause frames can not be configured through ethtool now, but ethtool can
report the supported mode.
Fixes: 265aeb511bd5 ("nfp: add support for .get_link_ksettings()") Signed-off-by: Fei Qin <fei.qin@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 58acd1009226 ("sctp: update active_key for asoc when old key is
being replaced"), sctp_auth_asoc_init_active_key() is called to update
the active_key right after the old key is deleted and before the new key
is added, and it caused that the active_key could be found with the key_id.
In Ying Xu's testing, the BUG_ON in sctp_auth_asoc_init_active_key() was
triggered:
So fix it by moving the active_key update after sh_keys is added.
Fixes: 58acd1009226 ("sctp: update active_key for asoc when old key is being replaced") Reported-by: Ying Xu <yinxu@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixing a typo that causes a cache entry to shrink immediately after adding
to it new MRs if the entry size exceeds the high limit. In doing so, the
cache misses its purpose to prevent the creation of new mkeys on the
runtime by using the cached ones.
Fixes: b9358bdbc713 ("RDMA/mlx5: Fix locking in MR cache work queue") Link: https://lore.kernel.org/r/fcb546986be346684a016f5ca23a0567399145fa.1627370131.git.leonro@nvidia.com Signed-off-by: Aharon Landau <aharonl@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Replace pci_enable_device() with pcim_enable_device(),
pci_disable_device() and pci_release_regions() will be
called in release automatically.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wang Hai <wanghai38@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>