When the TLS cipher suite uses CCM mode, including AES CCM and
SM4 CCM, the first byte of the B0 block is flags, and the real
IV starts from the second byte. The XOR operation of the IV and
rec_seq should be skip this byte, that is, add the iv_offset.
Fixes: f295b3ae9f59 ("net/tls: Add support of AES128-CCM based ciphers") Signed-off-by: Tianjia Zhang <tianjia.zhang@linux.alibaba.com> Cc: Vakul Garg <vakul.garg@nxp.com> Cc: stable@vger.kernel.org # v5.2+ Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit c8c3735997a3 ("parisc: Enhance detection of synchronous cr16
clocksources") I assumed that CPUs on the same physical core are syncronous.
While booting up the kernel on two different C8000 machines, one with a
dual-core PA8800 and one with a dual-core PA8900 CPU, this turned out to be
wrong. The symptom was that I saw a jump in the internal clocks printed to the
syslog and strange overall behaviour. On machines which have 4 cores (2
dual-cores) the problem isn't visible, because the current logic already marked
the cr16 clocksource unstable in this case.
This patch now marks the cr16 interval timers unstable if we have more than one
CPU in the system, and it fixes this issue.
In some very rare cases the init flow may fail. In many cases, this is
recoverable, so we can retry. Implement a loop to retry two more times
after the first attempt failed.
This can happen in two different situations, namely during probe and
during mac80211 start. For the first case, a simple loop is enough.
For the second case, we need to add a flag to prevent mac80211 from
trying to restart it as well, leaving full control with the driver.
Commit f45709df7731 ("serial: 8250: Don't touch RTS modem control while
in rs485 mode") sought to prevent user space from interfering with rs485
communication by ignoring a TIOCMSET ioctl() which changes RTS polarity.
It did so in serial8250_do_set_mctrl(), which turns out to be too deep
in the call stack: When a uart_port is opened, RTS polarity is set by
the rs485-aware function uart_port_dtr_rts(). It calls down to
serial8250_do_set_mctrl() and that particular RTS polarity change should
*not* be ignored.
The user-visible result is that on 8250_omap ports which use rs485 with
inverse polarity (RTS bit in MCR register is 1 to receive, 0 to send),
a newly opened port initially sets up RTS for sending instead of
receiving. That's because omap_8250_startup() sets the cached value
up->mcr to 0 and omap_8250_restore_regs() subsequently writes it to the
MCR register. Due to the commit, serial8250_do_set_mctrl() preserves
that incorrect register value:
Have pericom_do_set_divisor() use the uartclk instead of a hard coded
value to work with different speed crystals. Tested with 14.7456 and 24
MHz crystals.
Have pericom_do_set_divisor() always calculate the divisor rather than
call serial8250_do_set_divisor() for rates below baud_base.
Do not write registers or call serial8250_do_set_divisor() if valid
divisors could not be found.
Fixes: 6bf4e42f1d19 ("serial: 8250: Add support for higher baud rates to Pericom chips") Cc: stable <stable@vger.kernel.org> Signed-off-by: Jay Dolan <jay.dolan@accesio.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20211122120604.3909-3-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix error in table for PCI_DEVICE_ID_ACCESIO_PCIE_ICM_4S that caused it
and PCI_DEVICE_ID_ACCESIO_PCIE_ICM232_4 to be missing their fourth port.
Fixes: 78d3820b9bd3 ("serial: 8250_pci: Have ACCES cards that use the four port Pericom PI7C9X7954 chip use the pci_pericom_setup()") Cc: stable <stable@vger.kernel.org> Signed-off-by: Jay Dolan <jay.dolan@accesio.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20211122120604.3909-2-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 761ed4a94582 ("tty: serial_core: convert uart_close to use
tty_port_close") converted serial core to use tty_port_close() but
failed to notice that the transmit buffer still needs to be freed on
final close.
Not freeing the transmit buffer means that the buffer is no longer
cleared on next open so that any ioctl() waiting for the buffer to drain
might wait indefinitely (e.g. on termios changes) or that stale data can
end up being transmitted in case tx is restarted.
Furthermore, the buffer of any port that has been opened would leak on
driver unbind.
Note that the port lock is held when clearing the buffer pointer due to
the ldisc race worked around by commit a5ba1d95e46e ("uart: fix race
between uart_put_char() and uart_shutdown()").
Also note that the tty-port shutdown() callback is not called for
console ports so it is not strictly necessary to free the buffer page
after releasing the lock (cf. d72402145ace ("tty/serial: do not free
trasnmit buffer page under port lock")).
The current implementation uses 0 as lower limit for the baud rate
tolerance for tegra20 and tegra30 chips which causes isses on UART
initialization as soon as baud rate clock is lower than required even
when within the standard UART tolerance of +/- 4%.
This fix aligns the implementation with the initial commit description
of +/- 4% tolerance for tegra chips other than tegra186 and
tegra194.
The document 'ACPI for Arm Components 1.0' defines the following
_HID mappings:
-'Prime cell UART (PL011)': ARMH0011
-'SBSA UART': ARMHB000
Use the sbsa-uart driver when a device is described with
the 'ARMHB000' _HID.
Note:
PL011 devices currently use the sbsa-uart driver instead of the
uart-pl011 driver. Indeed, PL011 devices are not bound to a clock
in ACPI. It is not possible to change their baudrate.
The CONSOLE_POLLING mode is used for tools like k(g)db. In this kind of
setup, it is often sharing a serial device with the normal system console.
This is usually no problem because the polling helpers can consume input
values directly (when in kgdb context) and the normal Linux handlers can
only consume new input values after kgdb switched back.
This is not true anymore when RX DMA is enabled for UARTDM controllers.
Single input values can no longer be received correctly. Instead following
seems to happen:
* on 1. input, some old input is read (continuously)
* on 2. input, two old inputs are read (continuously)
* on 3. input, three old input values are read (continuously)
* on 4. input, 4 previous inputs are received
This repeats then for each group of 4 input values.
This behavior changes slightly depending on what state the controller was
when the first input was received. But this makes working with kgdb
basically impossible because control messages are always corrupted when
kgdboc tries to parse them.
RX DMA should therefore be off when CONSOLE_POLLING is enabled to avoid
these kind of problems. No such problem was noticed for TX DMA.
The trampoline_pgd only maps the 0xfffffff000000000-0xffffffffffffffff
range of kernel memory (with 4-level paging). This range contains the
kernel's text+data+bss mappings and the module mapping space but not the
direct mapping and the vmalloc area.
This is enough to get the application processors out of real-mode, but
for code that switches back to real-mode the trampoline_pgd is missing
important parts of the address space. For example, consider this code
from arch/x86/kernel/reboot.c, function machine_real_restart() for a
64-bit kernel:
The code switches to the trampoline_pgd, which unmaps the direct mapping
and also the kernel stack. The call to cr4_clear_bits() will find no
stack and crash the machine. The real_mode_header pointer below points
into the direct mapping, and dereferencing it also causes a crash.
The reason this does not crash always is only that kernel mappings are
global and the CR3 switch does not flush those mappings. But if theses
mappings are not in the TLB already, the above code will crash before it
can jump to the real-mode stub.
Extend the trampoline_pgd to contain all kernel mappings to prevent
these crashes and to make code which runs on this page-table more
robust.
There are cases that the TSC clocksource is wrongly judged as unstable by
the clocksource watchdog mechanism which tries to validate the TSC against
HPET, PM_TIMER or jiffies. While there is hardly a general reliable way to
check the validity of a watchdog, Thomas Gleixner proposed [1]:
"I'm inclined to lift that requirement when the CPU has:
After two decades of horrors we're finally at a point where TSC seems
to be halfway reliable and less abused by BIOS tinkerers. TSC_ADJUST
was really key as we can now detect even small modifications reliably
and the important point is that we can cure them as well (not pretty
but better than all other options)."
As feature #3 X86_FEATURE_NONSTOP_TSC_S3 only exists on several generations
of Atom processorz, and is always coupled with X86_FEATURE_CONSTANT_TSC
and X86_FEATURE_NONSTOP_TSC, skip checking it, and also be more defensive
to use maximal 2 sockets.
The check is done inside tsc_init() before registering 'tsc-early' and
'tsc' clocksources, as there were cases that both of them had been
wrongly judged as unreliable.
For more background of tsc/watchdog, there is a good summary in [2]
[tglx} Update vs. jiffies:
On systems where the only remaining clocksource aside of TSC is jiffies
there is no way to make this work because that creates a circular
dependency. Jiffies accuracy depends on not missing a periodic timer
interrupt, which is not guaranteed. That could be detected by TSC, but as
TSC is not trusted this cannot be compensated. The consequence is a
circulus vitiosus which results in shutting down TSC and falling back to
the jiffies clocksource which is even more unreliable.
The TSC_ADJUST register is checked every time a CPU enters idle state, but
Thomas Gleixner mentioned there is still a caveat that a system won't enter
idle [1], either because it's too busy or configured purposely to not enter
idle.
Setup a periodic timer (every 10 minutes) to make sure the check is
happening on a regular base.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
This change makes TCPM to wait in SNK_DEBOUNCED state until
CC1 and CC2 pins is SNK.Open for at least tPDDebounce. Previously,
TCPM resets the port if vbus is not present in PD_T_PS_SOURCE_ON.
This causes TCPM to loop continuously when connected to a
faulty power source that does not present vbus. Waiting in
SNK_DEBOUNCED also ensures that TCPM is adherant to
"4.5.2.2.4.2 Exiting from AttachWait.SNK State" requirements.
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d3564f ("xhci: Fix command ring pointer corruption while aborting a command") Cc: stable@vger.kernel.org Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
caused by `c->vc_cell_height' not having been initialized. This has
only started to trigger with commit 860dafa90259 ("vt: Fix character
height handling with VT_RESIZEX"), however the ultimate offender is
commit 50ec42edd978 ("[PATCH] Detaching fbcon: fix vgacon to allow
retaking of the console").
Said commit has added a call to `vc_resize' whenever `vgacon_init' is
called with the `init' argument set to 0, which did not happen before.
And the call is made before a key vgacon boot parameter retrieved in
`vgacon_startup' has been propagated in `vgacon_init' for `vc_resize' to
use to the console structure being worked on. Previously the parameter
was `c->vc_font.height' and now it is `c->vc_cell_height'.
In this particular scenario the registration of fbcon has failed and vt
resorts to vgacon. Now fbcon does have initialized `c->vc_font.height'
somehow, unlike `c->vc_cell_height', which is why this code did not
crash before, but either way the boot parameters should have been copied
to the console structure ahead of the call to `vc_resize' rather than
afterwards, so that first the call has a chance to use them and second
they do not change the console structure to something possibly different
from what was used by `vc_resize'.
Move the propagation of the vgacon boot parameters ahead of the call to
`vc_resize' then. Adjust the comment accordingly.
Fixes: 50ec42edd978 ("[PATCH] Detaching fbcon: fix vgacon to allow retaking of the console") Cc: stable@vger.kernel.org # v2.6.18+ Reported-by: Wim Osterholt <wim@djo.tudelft.nl> Reported-by: Pavel V. Panteleev <panteleev_p@mcst.ru> Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk> Link: https://lore.kernel.org/r/alpine.DEB.2.21.2110252317110.58149@angie.orcam.me.uk Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On newer debian releases the debian-provided "installkernel" script is
installed in /usr/sbin. Fix the kernel install.sh script to look for the
script in this directory as well.
Default KBUILD_IMAGE to $(boot)/bzImage if a self-extracting
(CONFIG_PARISC_SELF_EXTRACT=y) kernel is to be built.
This fixes the bindeb-pkg make target.
18ec54fdd6d18 ("x86/speculation: Prepare entry code for Spectre v1 swapgs mitigations")
added FENCE_SWAPGS_{KERNEL|USER}_ENTRY for conditional SWAPGS. In
paranoid_entry(), it uses only FENCE_SWAPGS_KERNEL_ENTRY for both
branches. This is because the fence is required for both cases since the
CR3 write is conditional even when PTI is enabled.
But
96b2371413e8f ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry")
changed the order of SWAPGS and the CR3 write. And it missed the needed
FENCE_SWAPGS_KERNEL_ENTRY for the user gsbase case.
Add it back by changing the branches so that FENCE_SWAPGS_KERNEL_ENTRY
can cover both branches.
[ bp: Massage, fix typos, remove obsolete comment while at it. ]
Fixes: 96b2371413e8f ("x86/entry/64: Switch CR3 before SWAPGS in paranoid entry") Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com> Signed-off-by: Borislav Petkov <bp@suse.de> Link: https://lkml.kernel.org/r/20211126101209.8613-2-jiangshanlai@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
SWAPGS is used only for interrupts coming from user mode or for
returning to user mode. So there is no reason to use the PARAVIRT
framework, as it can easily be replaced by an ALTERNATIVE depending
on X86_FEATURE_XENPV.
There are several instances using the PV-aware SWAPGS macro in paths
which are never executed in a Xen PV guest. Replace those with the
plain swapgs instruction. For SWAPGS_UNSAFE_STACK the same applies.
Commit d81ae8aac85c ("sched/uclamp: Fix initialization of struct
uclamp_rq") introduced a bug where uclamp_max of the rq is not reset to
match the woken up task's uclamp_max when the rq is idle.
The code was relying on rq->uclamp_max initialized to zero, so on first
enqueue
if (uc_se->value > READ_ONCE(uc_rq->value))
WRITE_ONCE(uc_rq->value, uc_se->value);
}
was actually resetting it. But since commit d81ae8aac85c changed the
default to 1024, this no longer works. And since rq->uclamp_flags is
also initialized to 0, neither above code path nor uclamp_idle_reset()
update the rq->uclamp_max on first wake up from idle.
This is only visible from first wake up(s) until the first dequeue to
idle after enabling the static key. And it only matters if the
uclamp_max of this task is < 1024 since only then its uclamp_max will be
effectively ignored.
Fix it by properly initializing rq->uclamp_flags = UCLAMP_FLAG_IDLE to
ensure uclamp_idle_reset() is called which then will update the rq
uclamp_max value as expected.
In the native case, PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is the
trampoline stack. But XEN pv doesn't use trampoline stack, so
PER_CPU_VAR(cpu_tss_rw + TSS_sp0) is also the kernel stack.
In that case, source and destination stacks are identical, which means
that reusing swapgs_restore_regs_and_return_to_usermode() in XEN pv
would cause %rsp to move up to the top of the kernel stack and leave the
IRET frame below %rsp.
This is dangerous as it can be corrupted if #NMI / #MC hit as either of
these events occurring in the middle of the stack pushing would clobber
data on the (original) stack.
And, with XEN pv, swapgs_restore_regs_and_return_to_usermode() pushing
the IRET frame on to the original address is useless and error-prone
when there is any future attempt to modify the code.
[ bp: Massage commit message. ]
Fixes: 7f2590a110b8 ("x86/entry/64: Use a per-CPU trampoline stack for IDT entries") Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com> Link: https://lkml.kernel.org/r/20211126101209.8613-4-jiangshanlai@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
removed a CR3 write in the faulting path of load_gs_index().
But the path's FENCE_SWAPGS_USER_ENTRY has no fence operation if PTI is
enabled, see spectre_v1_select_mitigation().
Rather, it depended on the serializing CR3 write of SWITCH_TO_KERNEL_CR3
and since it got removed, add a FENCE_SWAPGS_KERNEL_ENTRY call to make
sure speculation is blocked.
Properly type the operands being passed to __put_user()/__get_user().
Otherwise, these routines truncate data for dependent instructions
(e.g., INSW) and only read/write one byte.
This has been tested by sending a string with REP OUTSW to a port and
then reading it back in with REP INSW on the same port.
Previous behavior was to only send and receive the first char of the
size. For example, word operations for "abcd" would only read/write
"ac". With change, the full string is now written and read back.
Fixes: f980f9c31a923 (x86/sev-es: Compile early handler code into kernel image) Signed-off-by: Michael Sterritt <sterritt@google.com> Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Marc Orr <marcorr@google.com> Reviewed-by: Peter Gonda <pgonda@google.com> Reviewed-by: Joerg Roedel <jroedel@suse.de> Link: https://lkml.kernel.org/r/20211119232757.176201-1-sterritt@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The error paths in the prepare_vmcs02() function are supposed to set
*entry_failure_code but this path does not. It leads to using an
uninitialized variable in the caller.
Fixes: 71f7347025bf ("KVM: nVMX: Load GUEST_IA32_PERF_GLOBAL_CTRL MSR on VM-Entry") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Message-Id: <20211130125337.GB24578@kili> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
dmesg will report a #GP warning from an unchecked MSR access
error on MSR_F15H_PERF_CTLx.
This is because according to APM (Revision: 4.03) Figure 13-7,
the bits [35:32] of AMD PerfEvtSeln register is a part of the
event select encoding, which extends the EVENT_SELECT field
from 8 bits to 12 bits.
Opportunistically update pmu->reserved_bits for reserved bit 19.
Reported-by: Jim Mattson <jmattson@google.com> Fixes: ca724305a2b0 ("KVM: x86/vPMU: Implement AMD vPMU code for KVM") Signed-off-by: Like Xu <likexu@tencent.com>
Message-Id: <20211118130320.95997-1-likexu@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At the late production stages new dev ids were introduced. These are
now in production, so its important for the driver to recognize these.
And also fix the board caps for AQC115C adapter.
Fixes: b3f0c79cba206 ("net: atlantic: A2 hw_ops skeleton") Signed-off-by: Nikita Danilov <ndanilov@aquantia.com> Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 2.5G is advertised, N-Base should be advertised against the T-base
caps. N5G is out of use in baseline code and driver should treat both 5G
and N5G (and also 2.5G and N2.5G) equally from user perspective.
Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops") Signed-off-by: Nikita Danilov <ndanilov@aquantia.com> Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The max waiting period (of 1 ms) while reading the data from FW shared
buffer is too small for certain types of data (e.g., stats). There's a
chance that FW could be updating buffer at the same time and driver
would be unsuccessful in reading data. Firmware manual recommends to
have 1 sec timeout to fix this issue.
Fixes: 5cfd54d7dc186 ("net: atlantic: minimal A2 fw_ops") Signed-off-by: Dmitry Bogdanov <dbezrukov@marvell.com> Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In particular, we need to ensure all the necessary blocks are switched
to 64b mode (a5xx+) otherwise the high bits of the address of the BO to
snapshot state into will be ignored, resulting in:
Fixes: 4f776f4511c7 ("drm/msm/gpu: Convert the GPU show function to use the GPU state") Signed-off-by: Rob Clark <robdclark@chromium.org> Link: https://lore.kernel.org/r/20211108180122.487859-1-robdclark@gmail.com Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 142639a52a01 ("drm/msm/a6xx: fix crashstate capture for
A650") we changed a6xx_get_gmu_registers() to read 3 sets of
registers. Unfortunately, we didn't change the memory allocation for
the array. That leads to a KASAN warning (this was on the chromeos-5.4
kernel, which has the problematic commit backported to it):
BUG: KASAN: slab-out-of-bounds in _a6xx_get_gmu_registers+0x144/0x430
Write of size 8 at addr ffffff80c89432b0 by task A618-worker/209
CPU: 5 PID: 209 Comm: A618-worker Tainted: G W 5.4.156-lockdep #22
Hardware name: Google Lazor Limozeen without Touchscreen (rev5 - rev8) (DT)
Call trace:
dump_backtrace+0x0/0x248
show_stack+0x20/0x2c
dump_stack+0x128/0x1ec
print_address_description+0x88/0x4a0
__kasan_report+0xfc/0x120
kasan_report+0x10/0x18
__asan_report_store8_noabort+0x1c/0x24
_a6xx_get_gmu_registers+0x144/0x430
a6xx_gpu_state_get+0x330/0x25d4
msm_gpu_crashstate_capture+0xa0/0x84c
recover_worker+0x328/0x838
kthread_worker_fn+0x32c/0x574
kthread+0x2dc/0x39c
ret_from_fork+0x10/0x18
When smc_close_final() returns error, the return code overwrites by
kernel_sock_shutdown() in smc_close_active(). The return code of
smc_close_final() is more important than kernel_sock_shutdown(), and it
will pass to userspace directly.
Fix it by keeping both return codes, if smc_close_final() raises an
error, return it or kernel_sock_shutdown()'s.
Link: https://lore.kernel.org/linux-s390/1f67548e-cbf6-0dce-82b5-10288a4583bd@linux.ibm.com/ Fixes: 606a63c9783a ("net/smc: Ensure the active closing peer first closes clcsock") Suggested-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Tony Lu <tonylu@linux.alibaba.com> Reviewed-by: Wen Gu <guwen@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct an error where setting /proc/sys/net/rds/tcp/rds_tcp_rcvbuf would
instead modify the socket's sk_sndbuf and would leave sk_rcvbuf untouched.
Fixes: c6a58ffed536 ("RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket") Signed-off-by: William Kucharski <william.kucharski@oracle.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
smc_lgr_cleanup_early() meant to delete the link
group from the link group list, but it deleted
the list head by mistake.
This may cause memory corruption since we didn't
remove the real link group from the list and later
memseted the link group structure.
We got a list corruption panic when testing:
Fixes: a0a62ee15a829 ("net/smc: separate locks for SMCD and SMCR link group lists") Signed-off-by: Dust Li <dust.li@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before commit faa041a40b9f ("ipv4: Create cleanup helper for fib_nh")
changes to net->ipv4.fib_num_tclassid_users were protected by RTNL.
After the change, this is no longer the case, as free_fib_info_rcu()
runs after rcu grace period, without rtnl being held.
Fixes: faa041a40b9f ("ipv4: Create cleanup helper for fib_nh") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: David Ahern <dsahern@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 28712 Comm: syz-executor.0 Tainted: G W 5.16.0-rc1-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Link: https://lore.kernel.org/r/20211130170155.2331929-1-eric.dumazet@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit c55211892f46 ("dpaa2-eth: support PTP Sync packet one-step
timestamping") forgets to destroy workqueue at the end of remove
function.
Fix this by adding destroy_workqueue before fsl_mc_portal_free and
free_netdev.
Fixes: c55211892f46 ("dpaa2-eth: support PTP Sync packet one-step timestamping") Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'bitmap_fill()' fills a bitmap one 'long' at a time.
It is likely that an exact number of bits is expected.
Use 'bitmap_set()' instead in order not to set unexpected bits.
Fixes: e531f76757eb ("net: mvpp2: handle cases where more CPUs are available than s/w threads") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On most systems request for IRQ 0 will fail, phylib will print an error message
and fall back to polling. To fix this set the phydev->irq to PHY_POLL if no IRQ
is available.
Fixes: cc89c323a30e ("lan78xx: Use irq_domain for phy interrupt from USB Int. EP") Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Sven Schuchmann <schuchmann@schleissheimer.de> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Need to call rxrpc_put_local() for peer candidate before kfree() as it
holds a ref to rxrpc_local.
[DH: v2: Changed to abstract the peer freeing code out into a function]
Fixes: 9ebeddef58c4 ("rxrpc: rxrpc_peer needs to hold a ref on the rxrpc_local record") Signed-off-by: Eiichi Tsukata <eiichi.tsukata@nutanix.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Link: https://lore.kernel.org/all/20211121041608.133740-2-eiichi.tsukata@nutanix.com/ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the AHUB driver accordingly.
Fixes: 16e1bcc2caf4 ("ASoC: tegra: Add Tegra210 based AHUB driver") Signed-off-by: Sameer Pujar <spujar@nvidia.com> Suggested-by: Jaroslav Kysela <perex@perex.cz> Suggested-by: Mark Brown <broonie@kernel.org> Reviewed-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/1637219231-406-12-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the DSPK driver accordingly.
Fixes: 327ef6470266 ("ASoC: tegra: Add Tegra186 based DSPK driver") Suggested-by: Jaroslav Kysela <perex@perex.cz> Suggested-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sameer Pujar <spujar@nvidia.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/1637219231-406-11-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the DMIC driver accordingly.
Fixes: 8c8ff982e9e2 ("ASoC: tegra: Add Tegra210 based DMIC driver") Suggested-by: Jaroslav Kysela <perex@perex.cz> Suggested-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sameer Pujar <spujar@nvidia.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/1637219231-406-10-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the I2S driver accordingly.
Fixes: c0bfa98349d1 ("ASoC: tegra: Add Tegra210 based I2S driver") Suggested-by: Jaroslav Kysela <perex@perex.cz> Suggested-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sameer Pujar <spujar@nvidia.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/1637219231-406-9-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kcontrol put callback is expected to return 1 when there is change
in HW or when the update is acknowledged by driver. This would ensure
that change notifications are sent to subscribed applications. Update
the ADMAIF driver accordingly.
Fixes: f74028e159bb ("ASoC: tegra: Add Tegra210 based ADMAIF driver") Suggested-by: Jaroslav Kysela <perex@perex.cz> Suggested-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sameer Pujar <spujar@nvidia.com> Reviewed-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/1637219231-406-8-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 37f4ca907c46 ("mt76: mt7915: register per-phy HE capabilities for each interface") Fixes: e57b7901469f ("mt76: add mac80211 driver for MT7915 PCIe-based chipsets") Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org> Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/ddae419a740f1fb9e48afd432035e9f394f512ee.1637239456.git.lorenzo@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In mlx4_en_try_alloc_resources(), mlx4_en_copy_priv() is called and
tmp->tx_cq will be freed on the error path of mlx4_en_copy_priv().
After that mlx4_en_alloc_resources() is called and there is a dereference
of &tmp->tx_cq[t][i] in mlx4_en_alloc_resources(), which could lead to
a use after free problem on failure of mlx4_en_copy_priv().
Fix this bug by adding a check of mlx4_en_copy_priv()
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_MLX4_EN=m show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: ec25bc04ed8e ("net/mlx4_en: Add resilience in low memory systems") Signed-off-by: Zhou Qingyang <zhou1615@umn.edu> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20211130164438.190591-1-zhou1615@umn.edu Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When branch target identifiers are in use, code reachable via an
indirect branch requires a BTI landing pad at the branch target site.
When building FTRACE_WITH_REGS atop patchable-function-entry, we miss
BTIs at the start start of the `ftrace_caller` and `ftrace_regs_caller`
trampolines, and when these are called from a module via a PLT (which
will use a `BR X16`), we will encounter a BTI failure, e.g.
Fix this by adding the required `BTI C`, as we only require these to be
reachable via BL for direct calls or BR X16/X17 for PLTs. For now, these
are open-coded in the function prologue, matching the style of the
`__hwasan_tag_mismatch` trampoline.
In future we may wish to consider adding a new SYM_CODE_START_*()
variant which has an implicit BTI.
When ftrace is built atop mcount, the trampolines are marked with
SYM_FUNC_START(), and so get an implicit BTI. We may need to change
these over to SYM_CODE_START() in future for RELIABLE_STACKTRACE, in
case we need to apply special care aroud the return address being
rewritten.
Fixes: 97fed779f2a6 ("arm64: bti: Provide Kconfig for kernel mode BTI") Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Mark Brown <broonie@kernel.org> Cc: Will Deacon <will@kernel.org> Reviewed-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20211129135709.2274019-1-mark.rutland@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On ARM v6 and later, we define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
because the ordinary load/store instructions (ldr, ldrh, ldrb) can
tolerate any misalignment of the memory address. However, load/store
double and load/store multiple instructions (ldrd, ldm) may still only
be used on memory addresses that are 32-bit aligned, and so we have to
use the CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS macro with care, or we
may end up with a severe performance hit due to alignment traps that
require fixups by the kernel. Testing shows that this currently happens
with clang-13 but not gcc-11. In theory, any compiler version can
produce this bug or other problems, as we are dealing with undefined
behavior in C99 even on architectures that support this in hardware,
see also https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100363.
Fortunately, the get_unaligned() accessors do the right thing: when
building for ARMv6 or later, the compiler will emit unaligned accesses
using the ordinary load/store instructions (but avoid the ones that
require 32-bit alignment). When building for older ARM, those accessors
will emit the appropriate sequence of ldrb/mov/orr instructions. And on
architectures that can truly tolerate any kind of misalignment, the
get_unaligned() accessors resolve to the leXX_to_cpup accessors that
operate on aligned addresses.
Since the compiler will in fact emit ldrd or ldm instructions when
building this code for ARM v6 or later, the solution is to use the
unaligned accessors unconditionally on architectures where this is
known to be fast. The _aligned version of the hash function is
however still needed to get the best performance on architectures
that cannot do any unaligned access in hardware.
This new version avoids the undefined behavior and should produce
the fastest hash on all architectures we support.
There are various problems related to netlink notifications for mpls route
changes in response to interfaces being deleted:
* delete interface of only nexthop
DELROUTE notification is missing RTA_OIF attribute
* delete interface of non-last nexthop
NEWROUTE notification is missing entirely
* delete interface of last nexthop
DELROUTE notification is missing nexthop
All of these problems stem from the fact that existing routes are modified
in-place before sending a notification. Restructure mpls_ifdown() to avoid
changing the route in the DELROUTE cases and to create a copy in the
NEWROUTE case.
Fixes: f8efb73c97e2 ("mpls: multipath route support") Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In qlcnic_83xx_add_rings(), the indirect function of
ahw->hw_ops->alloc_mbx_args will be called to allocate memory for
cmd.req.arg, and there is a dereference of it in qlcnic_83xx_add_rings(),
which could lead to a NULL pointer dereference on failure of the
indirect function like qlcnic_83xx_alloc_mbx_args().
Fix this bug by adding a check of alloc_mbx_args(), this patch
imitates the logic of mbx_cmd()'s failure handling.
This bug was found by a static analyzer. The analysis employs
differential checking to identify inconsistent security operations
(e.g., checks or kfrees) between two code paths and confirms that the
inconsistent operations are not recovered in the current function or
the callers, so they constitute bugs.
Note that, as a bug found by static analysis, it can be a false
positive or hard to trigger. Multiple researchers have cross-reviewed
the bug.
Builds with CONFIG_QLCNIC=m show no new warnings, and our
static analyzer no longer warns about this code.
Steffen reported a TCP stream corruption for HTTP requests
served by the apache web-server using a cifs mount-point
and memory mapping the relevant file.
The root cause is quite similar to the one addressed by
commit 20eb4f29b602 ("net: fix sk_page_frag() recursion from
memory reclaim"). Here the nested access to the task page frag
is caused by a page fault on the (mmapped) user-space memory
buffer coming from the cifs file.
The page fault handler performs an smb transaction on a different
socket, inside the same process context. Since sk->sk_allaction
for such socket does not prevent the usage for the task_frag,
the nested allocation modify "under the hood" the page frag
in use by the outer sendmsg call, corrupting the stream.
The overall relevant stack trace looks like the following:
The cifs filesystem rightfully sets sk_allocations to GFP_NOFS,
we can avoid the nesting using the sk page frag for allocation
lacking the __GFP_FS flag. Do not define an additional mm-helper
for that, as this is strictly tied to the sk page frag usage.
v1 -> v2:
- use a stricted sk_page_frag() check instead of reordering the
code (Eric)
Reported-by: Steffen Froemer <sfroemer@redhat.com> Fixes: 5640f7685831 ("net: use a per task frag allocator") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix section mismatch warnings in xtsonic. The first one appears to be
bogus and after fixing the second one, the first one is gone.
WARNING: modpost: vmlinux.o(.text+0x529adc): Section mismatch in reference from the function sonic_get_stats() to the function .init.text:set_reset_devices()
The function sonic_get_stats() references
the function __init set_reset_devices().
This is often because sonic_get_stats lacks a __init
annotation or the annotation of set_reset_devices is wrong.
WARNING: modpost: vmlinux.o(.text+0x529b3b): Section mismatch in reference from the function xtsonic_probe() to the function .init.text:sonic_probe1()
The function xtsonic_probe() references
the function __init sonic_probe1().
This is often because xtsonic_probe lacks a __init
annotation or the annotation of sonic_probe1 is wrong.
Fixes: 74f2a5f0ef64 ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Finn Thain <fthain@telegraphics.com.au> Cc: Chris Zankel <chris@zankel.net> Cc: linux-xtensa@linux-xtensa.org Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Acked-by: Max Filippov <jcmvbkbc@gmail.com> Link: https://lore.kernel.org/r/20211130063947.7529-1-rdunlap@infradead.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CBUS transfers have always been atomic, but after commit 63b96983a5dd
("i2c: core: introduce callbacks for atomic transfers") we started to see
warnings during e.g. poweroff as the atomic callback is not explicitly set.
Fix that.
Fixes the following WARNING seen during Nokia N810 power down:
[ 786.570617] reboot: Power down
[ 786.573913] ------------[ cut here ]------------
[ 786.578826] WARNING: CPU: 0 PID: 672 at drivers/i2c/i2c-core.h:40 i2c_smbus_xfer+0x100/0x110
[ 786.587799] No atomic I2C transfer handler for 'i2c-2'
Fixes: 63b96983a5dd ("i2c: core: introduce callbacks for atomic transfers") Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
While handling an error during transfer (ex: NACK), it could
happen that the driver has already written data into TXDR
before the transfer get stopped.
This commit add TXDR Flush after end of transfer in case of error to
avoid sending a wrong data on any other slave upon next transfer.
Use 2-factor argument form kvcalloc() instead of kvzalloc().
Link: https://github.com/KSPP/linux/issues/162 Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
[Jason: Gustavo's link above is for KSPP, but this isn't actually a
security fix, as table_size is bounded to 8192 anyway, and gcc realizes
this, so the codegen comes out to be about the same.] Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we're being delivered packets from multiple CPUs so quickly that the
ring lock is contended for CPU tries, then it's safe to assume that the
queue is near capacity anyway, so just drop the packet rather than
spinning. This helps deal with multicore DoS that can interfere with
data path performance. It _still_ does not completely fix the issue, but
it again chips away at it.
Reported-by: Streun Fabio <fstreun@student.ethz.ch> Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently the spinlock on incoming_handshake's skb_queue is highly
contended, and a torrent of handshake or cookie packets can bring the
data plane to its knees, simply by virtue of enqueueing the handshake
packets to be processed asynchronously. So, we try switching this to a
ring buffer to hopefully have less lock contention. This alleviates the
problem somewhat, though it still isn't perfect, so future patches will
have to improve this further. However, it at least doesn't completely
diminish the data plane.
Reported-by: Streun Fabio <fstreun@student.ethz.ch> Reported-by: Joel Wanner <joel.wanner@inf.ethz.ch> Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each peer's endpoint contains a dst_cache entry that takes a reference
to another netdev. When the containing namespace exits, we take down the
socket and prevent future sockets from being created (by setting
creating_net to NULL), which removes that potential reference on the
netns. However, it doesn't release references to the netns that a netdev
cached in dst_cache might be taking, so the netns still might fail to
exit. Since the socket is gimped anyway, we can simply clear all the
dst_caches (by way of clearing the endpoint src), which will release all
references.
However, the current dst_cache_reset function only releases those
references lazily. But it turns out that all of our usages of
wg_socket_clear_peer_endpoint_src are called from contexts that are not
exactly high-speed or bottle-necked. For example, when there's
connection difficulty, or when userspace is reconfiguring the interface.
And in particular for this patch, when the netns is exiting. So for
those cases, it makes more sense to call dst_release immediately. For
that, we add a small helper function to dst_cache.
This patch also adds a test to netns.sh from Hangbin Liu to ensure this
doesn't regress.
Tested-by: Hangbin Liu <liuhangbin@gmail.com> Reported-by: Xiumei Mu <xmu@redhat.com> Cc: Toke Høiland-Jørgensen <toke@redhat.com> Cc: Paolo Abeni <pabeni@redhat.com> Fixes: 900575aa33a3 ("wireguard: device: avoid circular netns references") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DEBUG_PI_LIST was renamed to DEBUG_PLIST since 8e18faeac3 ("lib/plist:
rename DEBUG_PI_LIST to DEBUG_PLIST").
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com> Fixes: 8e18faeac3e4 ("lib/plist: rename DEBUG_PI_LIST to DEBUG_PLIST") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We previously removed the restriction on looping to self, and then added
a test to make sure the kernel didn't blow up during a routing loop. The
kernel didn't blow up, thankfully, but on certain architectures where
skb fragmentation is easier, such as ppc64, the skbs weren't actually
being discarded after a few rounds through. But the test wasn't catching
this. So actually test explicitly for massive increases in tx to see if
we have a routing loop. Note that the actual loop problem will need to
be addressed in a different commit.
Fixes: b673e24aad36 ("wireguard: socket: remove errant restriction on looping to self") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A __rcu annotation got lost during refactoring, which caused sparse to
become enraged.
Fixes: bf7b042dc62a ("wireguard: allowedips: free empty intermediate nodes when removing single node") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The selftests currently parse the kernel log at the end to track
potential memory leaks. With these tests now reading off the end of the
buffer, due to recent optimizations, some creation messages were lost,
making the tests think that there was a free without an alloc. Fix this
by increasing the kernel log size.
Fixes: 24b70eeeb4f4 ("wireguard: use synchronize_net rather than synchronize_rcu") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When comparing two strings for the "onmatch" histogram trigger, fields
that are strings use string comparisons, which do not care about being
signed or not.
Do not fail to match two string fields if one is unsigned char array and
the other is a signed char array.
Link: https://lore.kernel.org/all/20211129123043.5cfd687a@gandalf.local.home/ Cc: stable@vgerk.kernel.org Cc: Tom Zanussi <zanussi@kernel.org> Cc: Yafang Shao <laoar.shao@gmail.com> Fixes: b05e89ae7cf3b ("tracing: Accept different type for synthetic event fields") Reviewed-by: Masami Hiramatsu <mhiramatsu@kernel.org> Reported-by: Sven Schnelle <svens@linux.ibm.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
INVLPG operates on guest virtual address, which are represented by
vcpu->arch.walk_mmu. In nested virtualization scenarios,
kvm_mmu_invlpg() was using the wrong MMU structure; if L2's invlpg were
emulated by L0 (in practice, it hardly happen) when nested two-dimensional
paging is enabled, the call to ->tlb_flush_gva() would be skipped and
the hardware TLB entry would not be invalidated.
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20211124122055.64424-5-jiangshanlai@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having a signed (1 << 31) constant for TCR_EL2_RES1 and CPTR_EL2_TCPAC
causes the upper 32-bit to be set to 1 when assigning them to a 64-bit
variable. Bit 32 in TCR_EL2 is no longer RES0 in ARMv8.7: with FEAT_LPA2
it changes the meaning of bits 49:48 and 9:8 in the stage 1 EL2 page
table entries. As a result of the sign-extension, a non-VHE kernel can
no longer boot on a model with ARMv8.7 enabled.
CPTR_EL2 still has the top 32 bits RES0 but we should preempt any future
problems
Make these top bit constants unsigned as per commit df655b75c43f
("arm64: KVM: Avoid setting the upper 32 bits of VTCR_EL2 to 1").
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Reported-by: Chris January <Chris.January@arm.com> Cc: <stable@vger.kernel.org> Cc: Will Deacon <will@kernel.org> Cc: Marc Zyngier <maz@kernel.org> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20211125152014.2806582-1-catalin.marinas@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, checks for whether VT-d PI can be used refer to the current
status of the feature in the current vCPU; or they more or less pick
vCPU 0 in case a specific vCPU is not available.
However, these checks do not attempt to synchronize with changes to
the IRTE. In particular, there is no path that updates the IRTE when
APICv is re-activated on vCPU 0; and there is no path to wakeup a CPU
that has APICv disabled, if the wakeup occurs because of an IRTE
that points to a posted interrupt.
To fix this, always go through the VT-d PI path as long as there are
assigned devices and APICv is available on both the host and the VM side.
Since the relevant condition was copied over three times, take the hint
and factor it into a separate function.
Suggested-by: Sean Christopherson <seanjc@google.com> Cc: stable@vger.kernel.org Reviewed-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Reviewed-by: David Matlack <dmatlack@google.com>
Message-Id: <20211123004311.2954158-5-pbonzini@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flush the current VPID when handling KVM_REQ_TLB_FLUSH_GUEST instead of
always flushing vpid01. Any TLB flush that is triggered when L2 is
active is scoped to L2's VPID (if it has one), e.g. if L2 toggles CR4.PGE
and L1 doesn't intercept PGE writes, then KVM's emulation of the TLB
flush needs to be applied to L2's VPID.
Reported-by: Lai Jiangshan <jiangshanlai+lkml@gmail.com> Fixes: 07ffaf343e34 ("KVM: nVMX: Sync all PGDs on nested transition with shadow paging") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20211125014944.536398-2-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reject userspace memslots whose size exceeds the storage capacity of an
"unsigned long". KVM's uAPI takes the size as u64 to support large slots
on 64-bit hosts, but does not account for the size being truncated on
32-bit hosts in various flows. The access_ok() check on the userspace
virtual address in particular casts the size to "unsigned long" and will
check the wrong number of bytes.
KVM doesn't actually support slots whose size doesn't fit in an "unsigned
long", e.g. KVM's internal kvm_memory_slot.npages is an "unsigned long",
not a "u64", and misc arch specific code follows that behavior.
Fixes: fa3d315a4ce2 ("KVM: Validate userspace_addr of memslot when registered") Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Message-Id: <20211104002531.1176691-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[Why]
When trying to lightup two 4k60 non-DSC displays behind a branch device
that supports DSC we can't lightup both at once due to bandwidth
limitations - each requires 48 VCPI slots but we only have 63.
[How]
The workaround already exists in the code but is guarded by a CONFIG
that cannot be set by the user and shouldn't need to be.
Check for specific branch device IDs to device whether to enable
the workaround for multiple display scenarios.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com> Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel leaks memory when a `fib` rule is present in IPv6 nftables
firewall rules and a suppress_prefix rule is present in the IPv6 routing
rules (used by certain tools such as wg-quick). In such scenarios, every
incoming packet will leak an allocation in `ip6_dst_cache` slab cache.
After some hours of `bpftrace`-ing and source code reading, I tracked
down the issue to ca7a03c41753 ("ipv6: do not free rt if
FIB_LOOKUP_NOREF is set on suppress rule").
The problem with that change is that the generic `args->flags` always have
`FIB_LOOKUP_NOREF` set[1][2] but the IPv6-specific flag
`RT6_LOOKUP_F_DST_NOREF` might not be, leading to `fib6_rule_suppress` not
decreasing the refcount when needed.
How to reproduce:
- Add the following nftables rule to a prerouting chain:
meta nfproto ipv6 fib saddr . mark . iif oif missing drop
This can be done with:
sudo nft create table inet test
sudo nft create chain inet test test_chain '{ type filter hook prerouting priority filter + 10; policy accept; }'
sudo nft add rule inet test test_chain meta nfproto ipv6 fib saddr . mark . iif oif missing drop
- Run:
sudo ip -6 rule add table main suppress_prefixlength 0
- Watch `sudo slabtop -o | grep ip6_dst_cache` to see memory usage increase
with every incoming ipv6 packet.
This patch exposes the protocol-specific flags to the protocol
specific `suppress` function, and check the protocol-specific `flags`
argument for RT6_LOOKUP_F_DST_NOREF instead of the generic
FIB_LOOKUP_NOREF when decreasing the refcount, like this.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215105 Fixes: ca7a03c41753 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule") Cc: stable@vger.kernel.org Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Trying to remove the fsl-sata module in the PPC64 GNU/Linux
leads to the following warning:
------------[ cut here ]------------
remove_proc_entry: removing non-empty directory 'irq/69',
leaking at least 'fsl-sata[ff0221000.sata]'
WARNING: CPU: 3 PID: 1048 at fs/proc/generic.c:722
.remove_proc_entry+0x20c/0x220
IRQMASK: 0
NIP [c00000000033826c] .remove_proc_entry+0x20c/0x220
LR [c000000000338268] .remove_proc_entry+0x208/0x220
Call Trace:
.remove_proc_entry+0x208/0x220 (unreliable)
.unregister_irq_proc+0x104/0x140
.free_desc+0x44/0xb0
.irq_free_descs+0x9c/0xf0
.irq_dispose_mapping+0x64/0xa0
.sata_fsl_remove+0x58/0xa0 [sata_fsl]
.platform_drv_remove+0x40/0x90
.device_release_driver_internal+0x160/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
---[ end trace 0ea876d4076908f5 ]---
The driver creates the mapping by calling irq_of_parse_and_map(),
so it also has to dispose the mapping. But the easy way out is to
simply use platform_get_irq() instead of irq_of_parse_map(). Also
we should adapt return value checking and propagate error values.
In this case the mapping is not managed by the device but by
the of core, so the device has not to dispose the mapping.
Fixes: faf0b2e5afe7 ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller") Cc: stable@vger.kernel.org Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the `rmmod sata_fsl.ko` command is executed in the PPC64 GNU/Linux,
a bug is reported:
==================================================================
BUG: Unable to handle kernel data access on read at 0x80000800805b502c
Oops: Kernel access of bad area, sig: 11 [#1]
NIP [c0000000000388a4] .ioread32+0x4/0x20
LR [80000000000c6034] .sata_fsl_port_stop+0x44/0xe0 [sata_fsl]
Call Trace:
.free_irq+0x1c/0x4e0 (unreliable)
.ata_host_stop+0x74/0xd0 [libata]
.release_nodes+0x330/0x3f0
.device_release_driver_internal+0x178/0x2c0
.driver_detach+0x64/0xd0
.bus_remove_driver+0x70/0xf0
.driver_unregister+0x38/0x80
.platform_driver_unregister+0x14/0x30
.fsl_sata_driver_exit+0x18/0xa20 [sata_fsl]
.__se_sys_delete_module+0x1ec/0x2d0
.system_call_exception+0xfc/0x1f0
system_call_common+0xf8/0x200
==================================================================
The triggering of the BUG is shown in the following stack:
The iounmap(host_priv->hcr_base) and kfree(host_priv) functions should
not be executed in drv->remove. These functions should be executed in
host_stop after port_stop. Therefore, we move these functions to the
new function sata_fsl_host_stop and bind the new function to host_stop.
Fixes: faf0b2e5afe7 ("drivers/ata: add support to Freescale 3.0Gbps SATA Controller") Cc: stable@vger.kernel.org Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com> Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jann Horn points out that there is another possible race wrt Unix domain
socket garbage collection, somewhat reminiscent of the one fixed in
commit cbcf01128d0a ("af_unix: fix garbage collect vs MSG_PEEK").
See the extended comment about the garbage collection requirements added
to unix_peek_fds() by that commit for details.
The race comes from how we can locklessly look up a file descriptor just
as it is in the process of being closed, and with the right artificial
timing (Jann added a few strategic 'mdelay(500)' calls to do that), the
Unix domain socket garbage collector could see the reference count
decrement of the close() happen before fget() took its reference to the
file and the file was attached onto a new file descriptor.
This is all (intentionally) correct on the 'struct file *' side, with
RCU lookups and lockless reference counting very much part of the
design. Getting that reference count out of order isn't a problem per
se.
But the garbage collector can get confused by seeing this situation of
having seen a file not having any remaining external references and then
seeing it being attached to an fd.
In commit cbcf01128d0a ("af_unix: fix garbage collect vs MSG_PEEK") the
fix was to serialize the file descriptor install with the garbage
collector by taking and releasing the unix_gc_lock.
That's not really an option here, but since this all happens when we are
in the process of looking up a file descriptor, we can instead simply
just re-check that the file hasn't been closed in the meantime, and just
re-do the lookup if we raced with a concurrent close() of the same file
descriptor.
When running without MIO support, with pci=nomio or for devices which
are not MIO-capable the zPCI subsystem generates pseudo-MMIO addresses
to allow access to PCI BARs via MMIO based Linux APIs even though the
platform uses function handles and BAR numbers.
This is done by stashing an index into our global IOMAP array which
contains the function handle in the 16 most significant bits of the
addresses returned by ioremap() always setting the most significant bit.
On the other hand the MIO addresses assigned by the platform for use,
while requiring special instructions, allow PCI access with virtually
mapped physical addresses. Now the problem is that these MIO addresses
and our own pseudo-MMIO addresses may overlap, while functionally this
would not be a problem by itself this overlap is detected by common code
as both address types are added as resources in the iomem_resource tree.
This leads to the overlapping resource claim of either the MIO capable
or non-MIO capable devices with being rejected.
Since PCI is tightly coupled to the use of the iomem_resource tree, see
for example the code for request_mem_region(), we can't reasonably get
rid of the overlap being detected by keeping our pseudo-MMIO addresses
out of the iomem_resource tree.
Instead let's move the range used by our own pseudo-MMIO addresses by
starting at (1UL << 62) and only using addresses below (1UL << 63) thus
avoiding the range currently used for MIO addresses.
Fixes: c7ff0e918a7c ("s390/pci: deal with devices that have no support for MIO instructions") Cc: stable@vger.kernel.org # 5.3+ Reviewed-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I hot added a CPU, I found 'cpufreq' directory was not created
below /sys/devices/system/cpu/cpuX/.
It is because get_cpu_device() failed in add_cpu_dev_symlink().
cpufreq_add_dev() is the .add_dev callback of a CPU subsys interface.
It will be called when the CPU device registered into the system.
The call chain is as follows:
Currently when removing an ipmi_user the removal is deferred as a work on
the system's workqueue. Although this guarantees the free operation will
occur in non atomic context, it can race with the ipmi_msghandler module
removal (see [1]) . In case a remove_user work is scheduled for removal
and shortly after ipmi_msghandler module is removed we can end up in a
situation where the module is removed fist and when the work is executed
the system crashes with :
BUG: unable to handle page fault for address: ffffffffc05c3450
PF: supervisor instruction fetch in kernel mode
PF: error_code(0x0010) - not-present page
because the pages of the module are gone. In cleanup_ipmi() there is no
easy way to detect if there are any pending works to flush them before
removing the module. This patch creates a separate workqueue and schedules
the remove_work works on it. When removing the module the workqueue is
drained when destroyed to avoid the race.
As reported by Exuvo is possible that we have lot's of EPROTO errors
during device start i.e. firmware load. But after that device works
correctly. Hence marking device gone by few EPROTO errors done by
commit e383c70474db ("rt2x00: check number of EPROTO errors") caused
regression - Exuvo device stop working after kernel update. To fix
disable the check during device start.
The 'kprobe::data_size' is unsigned, thus it can not be negative. But if
user sets it enough big number (e.g. (size_t)-8), the result of 'data_size
+ sizeof(struct kretprobe_instance)' becomes smaller than sizeof(struct
kretprobe_instance) or zero. In result, the kretprobe_instance are
allocated without enough memory, and kretprobe accesses outside of
allocated memory.
To avoid this issue, introduce a max limitation of the
kretprobe::data_size. 4KB per instance should be OK.
IPCB/IP6CB need to be initialized when processing outbound v4 or v6 pkts
in the codepath of vrf device xmit function so that leftover garbage
doesn't cause futher code that uses the CB to incorrectly process the
pkt.
One occasion of the issue might occur when MPLS route uses the vrf
device as the outgoing device such as when the route is added using "ip
-f mpls route add <label> dev <vrf>" command.
The problems seems to exist since day one. Hence I put the day one
commits on the Fixes tags.
Fixes: 193125dbd8eb ("net: Introduce VRF device driver") Fixes: 35402e313663 ("net: Add IPv6 support to VRF device") Cc: stable@vger.kernel.org Signed-off-by: Stephen Suryaputra <ssuryaextr@gmail.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20211130162637.3249-1-ssuryaextr@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit ddfd9dcf270c ("ACPI: PM: Add acpi_[un]register_wakeup_handler()")
added new functions for drivers to use during the s2idle wakeup path, but
didn't add stubs for when CONFIG_ACPI wasn't set.
Add those stubs in for other drivers to be able to use.
Fixes: ddfd9dcf270c ("ACPI: PM: Add acpi_[un]register_wakeup_handler()") Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Link: https://lore.kernel.org/r/20211101014853.6177-1-mario.limonciello@amd.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Possible recursive locking is detected by lockdep when SMC
falls back to TCP. The corresponding warnings are as follows:
============================================
WARNING: possible recursive locking detected
5.16.0-rc1+ #18 Tainted: G E
--------------------------------------------
wrk/1391 is trying to acquire lock: ffff975246c8e7d8 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0x109/0x250 [smc]
but task is already holding lock: ffff975246c8f918 (&ei->socket.wq.wait){..-.}-{3:3}, at: smc_switch_to_fallback+0xfe/0x250 [smc]
other info that might help us debug this:
Possible unsafe locking scenario:
The nested locking in smc_switch_to_fallback() is considered to
possibly cause a deadlock because smc_wait->lock and clc_wait->lock
are the same type of lock. But actually it is safe so far since
there is no other place trying to obtain smc_wait->lock when
clc_wait->lock is held. So the patch replaces spin_lock() with
spin_lock_nested() to avoid false report by lockdep.
Link: https://lkml.org/lkml/2021/11/19/962 Fixes: 2153bd1e3d3d ("Transfer remaining wait queue entries during fallback") Reported-by: syzbot+e979d3597f48262cb4ee@syzkaller.appspotmail.com Signed-off-by: Wen Gu <guwen@linux.alibaba.com> Acked-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log