There is another MSI board (1462:cc34) that has dual Realtek codecs,
and we need to apply the existing quirk for fixing the conflicts of
Master control.
This adds a new SND_PCI_QUIRK(...) and applies it to the Intel NUC 10
devices. This fixes the issue of the devices not having audio input and
output on the headset jack because the kernel does not recognize when
something is plugged in.
The new quirk was inspired by the quirk for the Intel NUC 8 devices, but
it turned out that the NUC 10 uses another pin. This information was
acquired by black box testing likely pins.
This applies a SND_PCI_QUIRK(...) to the Clevo NH55RZQ barebone. This
fixes the issue of the device not recognizing a pluged in microphone.
The device has both, a microphone only jack, and a speaker + microphone
combo jack. The combo jack already works. The microphone-only jack does
not recognize when a device is pluged in without this patch.
This patch adds the missing MODULE_DEVICE_TABLE definitions on different
Mediatek phy drivers which generates correct modalias for automatic loading
when these drivers are compiled as an external module.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Link: https://lore.kernel.org/r/20210203110631.686003-1-enric.balletbo@collabora.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ICANON case is a bit messy, since it has to look for the line
ending, and has special code to then suppress line ending characters if
they match the __DISABLED_CHAR. So it actually looks up the line ending
even past the point where it knows it won't copy it to the result
buffer.
That said, apart from all those odd legacy N_TTY ICANON cases, the
actual "should we continue copying" logic isn't really all that
complicated or different from the non-canon case. In fact, the lack of
"wait for at least N characters" arguably makes the repeat case slightly
simpler. It really just boils down to "there's more of the line to be
copied".
So add the necessarily trivial logic, and now the N_TTY case will give
long result lines even when in canon mode.
With the conversion to do the tty ldisc read operations in small chunks,
the n_tty line discipline became noticeably slower for throughput
oriented loads, because rather than read things in up to 2kB chunks, it
would return at most 64 bytes per read() system call.
The cost is mainly all in the "do system calls over and over", not
really in the new "copy to an extra kernel buffer".
This can be fixed by teaching the n_tty line discipline about the
"cookie continuation" model, which the chunking code supports because
things like hdlc need to be able to handle packets up to 64kB in size.
Doing that doesn't just get us back to the old performace, but to much
better performance: my stupid "copy 10MB of data over a pty" test
program is now almost twice as fast as it used to be (going down from
0.1s to 0.054s).
This is entirely because it now creates maximal chunks (which happens to
be "one byte less than one page" due to how we do the circular tty
buffers).
NOTE! This case only handles the simpler non-icanon case, which is the
one where people may care about throughput. I'm going to do the icanon
case later too, because while performance isn't a major issue for that,
there may be programs that think they'll always get a full line and
don't like the 64-byte chunking for that reason.
Such programs are arguably buggy (signals etc can cause random partial
results from tty reads anyway), and good programs will handle such
partial reads, but expecting everybody to write "good programs" has
never been a winning policy for the kernel..
When I converted the tty_ldisc_ops 'read()' function to take a kernel
pointer, I was a bit too aggressive about the ldisc returning EOVERFLOW.
Yes, we want to have EOVERFLOW override any partially read data (because
the whole point is that the buffer was too small for the whole packet,
and we don't want to see partial packets), but it shouldn't override a
previous EFAULT.
And in fact, it really is just EOVERFLOW that is special and should
throw away any partially read data, not "any error". Admittedly
EOVERFLOW is currently the only one that can happen for a continuation
read - and if the first read iteration returns an error we won't have this issue.
So this is more of a technicality, but let's just make the intent very
explicit, and re-organize the error handling a bit so that this is all
clearer.
We're not factoring in the start of the file for where to write and
read the swapfile, which leads to very unfortunate side effects of
writing where we should not be...
Fixes: dd6bd0d9c7db ("swap: use bdev_read_page() / bdev_write_page()") Signed-off-by: Jens Axboe <axboe@kernel.dk> Cc: Anthony Iliopoulos <ailiop@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 9e2369c06c8a18 ("xen: add helpers to allocate unpopulated
memory") foreign mappings are using guest physical addresses allocated
via ZONE_DEVICE functionality.
This will result in problems for the case of no balloon memory hotplug
being configured, as the p2m list will only cover the initial memory
size of the domain. Any ZONE_DEVICE allocated address will be outside
the p2m range and thus a mapping can't be established with that memory
address.
Fix that by extending the p2m size for that case. At the same time add
a check for a to be created mapping to be within the p2m limits in
order to detect errors early.
While changing a comment, remove some 32-bit leftovers.
Commit 3194a1746e8a ("xen-netback: don't "handle" error by BUG()")
dropped respective a BUG_ON() without noticing that with this the
variable's value wouldn't be consumed anymore. With gnttab_set_map_op()
setting all status fields to a non-zero value, in case of an error no
slot should have a status of GNTST_okay (zero).
Bailing immediately from set_foreign_p2m_mapping() upon a p2m updating
error leaves the full batch in an ambiguous state as far as the caller
is concerned. Instead flags respective slots as bad, unmapping what
was mapped there right away.
HYPERVISOR_grant_table_op()'s return value and the individual unmap
slots' status fields get used only for a one-time - there's not much we
can do in case of a failure.
Note that there's no GNTST_enomem or alike, so GNTST_general_error gets
used.
The map ops' handle fields get overwritten just to be on the safe side.
Open-iSCSI sends passthrough PDUs over netlink, but the kernel should be
verifying that the provided PDU header and data lengths fall within the
netlink message to prevent accessing beyond that in memory.
Cc: stable@vger.kernel.org Reported-by: Adam Nichols <adam@grimm-co.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the iSCSI parameters are exported back through sysfs, it should be
enforcing that they never are more than PAGE_SIZE (which should be more
than enough) before accepting updates through netlink.
Change all iSCSI sysfs attributes to use sysfs_emit().
Cc: stable@vger.kernel.org Reported-by: Adam Nichols <adam@grimm-co.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Protect the iSCSI transport handle, available in sysfs, by requiring
CAP_SYS_ADMIN to read it. Also protect the netlink socket by restricting
reception of messages to ones sent with CAP_SYS_ADMIN. This disables
normal users from being able to end arbitrary iSCSI sessions.
Cc: stable@vger.kernel.org Reported-by: Adam Nichols <adam@grimm-co.com> Reviewed-by: Chris Leech <cleech@redhat.com> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Acer One S1002 tablet is using an analog mic on IN1 and has
its jack-detect connected to JD2_IN4N, instead of using the default
IN3 for its internal mic and JD1_IN4P for jack-detect.
Note it is also using AIF2 instead of AIF1 which is somewhat unusual,
this is correctly advertised in the ACPI CHAN package, so the speakers
do work without the quirk.
Add a quirk for the mic and jack-detect settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210216213555.36555-5-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a DMI quirk for the Jumper EZpad 7 tablet, this tablet has
a jack-detect switch which reads 1/high when a jack is inserted,
rather then using the standard active-low setup which most
jack-detect switches use. All other settings are using the defaults.
Add a DMI-quirk setting the defaults + the BYT_RT5651_JD_NOT_INV
flags for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210216213555.36555-4-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Voyo Winpad A15 tablet uses a Bay Trail (non CR) SoC, so it is using
SSP2 (AIF1) and it mostly works with the defaults. But instead of using
DMIC1 it is using an analog mic on IN1, add a quirk for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210216213555.36555-3-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Estar Beauty HD MID 7316R tablet almost fully works with out default
settings. The only problem is that it has only 1 speaker so any sounds
only playing on the right channel get lost.
Add a quirk for this model using the default settings + MONO_SPEAKER.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210216213555.36555-2-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Hung tasks and RCU stall cases were reported on systems which were not
100% busy. Investigation of such unexpected cases (no sign of potential
starvation caused by tasks hogging the system) pointed out that the
periodic sched tick timer wasn't serviced anymore after a certain point
and that caused all machinery that depends on it (timers, RCU, etc.) to
stop working as well. This issues was however only reproducible if
HRTICK was enabled.
Looking at core dumps it was found that the rbtree of the hrtimer base
used also for the hrtick was corrupted (i.e. next as seen from the base
root and actual leftmost obtained by traversing the tree are different).
Same base is also used for periodic tick hrtimer, which might get "lost"
if the rbtree gets corrupted.
Much alike what described in commit 1f71addd34f4c ("tick/sched: Do not
mess with an enqueued hrtimer") there is a race window between
hrtimer_set_expires() in hrtick_start and hrtimer_start_expires() in
__hrtick_restart() in which the former might be operating on an already
queued hrtick hrtimer, which might lead to corruption of the base.
Use hrtick_start() (which removes the timer before enqueuing it back) to
ensure hrtick hrtimer reprogramming is entirely guarded by the base
lock, so that no race conditions can occur.
Signed-off-by: Juri Lelli <juri.lelli@redhat.com> Signed-off-by: Luis Claudio R. Goncalves <lgoncalv@redhat.com> Signed-off-by: Daniel Bristot de Oliveira <bristot@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Link: https://lkml.kernel.org/r/20210208073554.14629-2-juri.lelli@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
I had a kernel IRQ stack overflow on the mx3210 debian buildd machine. This patch increases the
64-bit IRQ stack size to 64 KB. The 64-bit stack size needs to be larger than the 32-bit stack
size since registers are twice as big.
Signed-off-by: John David Anglin <dave.anglin@bell.net> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Current driver create DMIC dai based on quirk for each platforms,
so we need to add quirk for new platforms. Now driver reports DMIC
number to machine driver and machine driver can create DMIC dai based
on this information. The old check is reserved for some platforms
may be failed to set the DMIC number in BIOS.
Reviewed-by: Bard Liao <bard.liao@intel.com> Signed-off-by: Rander Wang <rander.wang@intel.com> Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210208233336.59449-6-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Cascade Lake Xeon parts have the same model number as Skylake Xeon
parts, so they are tagged with the intel_pebs_isolation
quirk. However, as with Skylake Xeon H0 stepping parts, the PEBS
isolation issue is fixed in all microcode versions.
Add the Cascade Lake Xeon steppings (5, 6, and 7) to the
isolation_ucodes[] table so that these parts benefit from Andi's
optimization in commit 9b545c04abd4f ("perf/x86/kvm: Avoid unnecessary
work in guest filtering").
While doing error injection I would sometimes get a corrupt file system.
This is because I was injecting errors at btrfs_search_slot, but would
only do it one time per stack. This uncovered a problem in
commit_fs_roots, where if we get an error we would just break. However
we're in a nested loop, the first loop being a loop to find all the
dirty fs roots, and then subsequent root updates would succeed clearing
the error value.
This isn't likely to happen in real scenarios, however we could
potentially get a random ENOMEM once and then not again, and we'd end up
with a corrupted file system. Fix this by moving the error checking
around a bit to the main loop, as this is the only place where something
will fail, and return the error as soon as it occurs.
With this patch my reproducer no longer corrupts the file system.
Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some Bay Trail systems:
1. Use a non CR version of the Bay Trail SoC
2. Contain at least 6 interrupt resources so that the
platform_get_resource(pdev, IORESOURCE_IRQ, 5) check to workaround
non CR systems which list their IPC IRQ at index 0 despite being
non CR does not work
3. Despite 1. and 2. still have their IPC IRQ at index 0 rather then 5
Add a DMI quirk table to check for the few known models with this issue,
so that the right IPC IRQ index is used on these systems.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210120214957.140232-5-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As with most Pioneer devices, the device descriptor is vendor specific
and as such, the number of channels, the PCM format, endpoints and
sample rate need to be specified. This device has 8 inputs and 8 outputs
and a sample rate of 48000 only. The PCM format is S24_3LE like other
devices.
There seems to be an appetite for reducing duplication amongs these
Pioneer patches but again, I feel this is a step to be taken after
support has been added as it's not completely clear where the
commonalities are.
Like the DJM-750, ensure that the format control message is passed to
the device when opening a stream. It seems as though fmt->sync_ep is not
always set when this function is called hence the passing of the value
at the call site. If this can be fixed, fmt->sync_up should be used as
the wvalue.
There doesn't seem to be a "cpu_to_le24" type function defined hence for
the open code but I did see a similar thing done in Bluez lib. Perhaps
we can get these definitions defined in byteorder.h. See hci_cpu_to_le24
in include/net/bluetooth/hci.h:2543 for similar usage.
If reconnect failed after start io queues, the queues will be unquiesced
and new requests continue to be delivered. Reconnection error handling
process directly free queues without cancel suspend requests. The
suppend request will time out, and then crash due to use the queue
after free.
Add sync queues and cancel suppend requests for reconnection error
handling.
A crash happens when inject failed reconnection.
If reconnect failed after start io queues, the queues will be unquiesced
and new requests continue to be delivered. Reconnection error handling
process directly free queues without cancel suspend requests. The
suppend request will time out, and then crash due to use the queue
after free.
Add sync queues and cancel suppend requests for reconnection error
handling.
[Why]
If the BIOS table is invalid or corrupt then get_i2c_info can fail
and we dereference a NULL pointer.
[How]
Check that ddc_pin is not NULL before using it and log an error if it
is because this is unexpected.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Eric Yang <eric.yang2@amd.com> Acked-by: Anson Jacob <anson.jacob@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This adds the Pioneer DJ DJM-750 to the quirks table and ensures
skip_pioneer_sync_ep() is (also) called: this device uses the vendor
ID of 0x08e4 (I'm not sure why they use multiple vendor IDs but many
just like to be awkward it seems).
Playback on all 8 channels works. I'll likely keep this working in the
future and submit futher patches and improvements as necessary.
Some devices, like mini PCs/media/top-set boxes do not have any speakers
at all, an example of the is the Mele PCG03 Mini PC.
Add a new BYT_RT5640_NO_SPEAKERS quirk-flag which when sets does not add
speaker routes and modifies the components and the (optional) long_name
strings to reflect that there are no speakers.
Cc: Rasmus Porsager <rasmus@beat.dk> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210109210119.159032-2-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
RX 5600 XT Pulse advertises support for BAR 0 being 256MB, 512MB,
or 1GB, but it also supports 2GB, 4GB, and 8GB. Add a rebar
size quirk so that the BAR 0 is big enough to cover complete VARM.
Similar to commit <b82175750131>("drm/amdgpu: fix IH overflow on Vega10 v2").
When an ring buffer overflow happens the appropriate bit is set in the WPTR
register which is also written back to memory. But clearing the bit in the
WPTR doesn't trigger another memory writeback.
So what can happen is that we end up processing the buffer overflow over and
over again because the bit is never cleared. Resulting in a random system
lockup because of an infinite loop in an interrupt handler.
Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Defang Bo <bodefang@126.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most callers check for non-zero return, and assume it's -ECHILD (which
it always will be). One caller uses the actual error return. Clean this
up and make it fully consistent, by having unlazy_walk() return a bool
instead. Rename it to try_to_unlazy() and return true on success, and
failure on error. That's easier to read.
No functional changes in this patch.
Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The signed long type used for printing the number of bytes processed in
tcrypt benchmarks limits the range to -/+ 2 GiB, which is not sufficient
to cover the performance of common accelerated ciphers such as AES-NI
when benchmarked with sec=1. So switch to u64 instead.
While at it, fix up a missing printk->pr_cont conversion in the AEAD
benchmark.
ac_classify() expects a struct sk_buff* as its second argument, which is
a member of struct tx_complete_data. priv happens to be a pointer to
struct tx_complete_data, so passing it directly to ac_classify() leads
to wrong behaviour and occasional panics.
Since there is only one caller of wilc_wlan_txq_add_net_pkt and it
already knows the type behind this pointer, and the structure is already
in the header file, change the function signature to use the real type
instead of void* in order to prevent confusion.
The Voyo winpad A15 tablet contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
rcmfmac4330-sdio.To be filled by O.E.M.-To be filled by O.E.M..txt
as nvram file which is a bit too generic.
Add a DMI quirk so that a unique and clearly identifiable nvram file name
is used on the Voyo winpad A15 tablet.
While preparing a matching linux-firmware update I noticed that the nvram
is identical to the nvram used on the Prowise-PT301 tablet, so the new DMI
quirk entry simply points to the already existing Prowise-PT301 nvram file.
The Predia Basic tablet contains quite generic names in the sys_vendor and
product_name DMI strings, without this patch brcmfmac will try to load:
brcmfmac43340-sdio.Insyde-CherryTrail.txt as nvram file which is a bit
too generic.
Add a DMI quirk so that a unique and clearly identifiable nvram file name
is used on the Predia Basic tablet.
It's possible that the length passed to ipa_header_size_encoded()
is larger than what can be represented by the HDR_LEN field alone
(starting with IPA v4.5). If we attempted that, u32_encode_bits()
would trigger a build-time error.
Avoid this problem by masking off high-order bits of the value
encoded as the lower portion of the header length.
The same sort of problem exists in ipa_metadata_offset_encoded(),
so implement the same fix there.
Signed-off-by: Alex Elder <elder@linaro.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some devices, e.g. the RTL8723BS bluetooth part, some USB attached devices,
completely drop from the bus on a system-suspend. These devices will
have their driver unbound and rebound on resume (when the dropping of
the bus gets detected) and will show up as a new HCI after resume.
These devices do not benefit from the suspend / resume handling work done
by the hci_suspend_notifier. At best this unnecessarily adds some time to
the suspend/resume time. But this may also actually cause problems, if the
code doing the driver unbinding runs after the pm-notifier then the
hci_suspend_notifier code will try to talk to a device which is now in
an uninitialized state.
This commit adds a new HCI_QUIRK_NO_SUSPEND_NOTIFIER quirk which allows
drivers to opt-out of the hci_suspend_notifier when they know beforehand
that their device will be fully re-initialized / reprobed on resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Ubiquiti U-Fiber Instant SFP GPON module has nonsensical information
stored in its EEPROM. It claims to support all transceiver types including
10G Ethernet. Clear all claimed modes and set only 1000baseX_Full, which is
the only one supported.
This module has also phys_id set to SFF, and the SFP subsystem currently
does not allow to use SFP modules detected as SFFs. Add exception for this
module so it can be detected as supported.
This change finally allows to detect and use SFP GPON module Ubiquiti
U-Fiber Instant on Linux system.
EEPROM content of this SFP module is (where XX is serial number):
00: 02 04 0b ff ff ff ff ff ff ff ff 03 0c 00 14 c8 ???........??.??
10: 00 00 00 00 55 42 4e 54 20 20 20 20 20 20 20 20 ....UBNT
20: 20 20 20 20 00 18 e8 29 55 46 2d 49 4e 53 54 41 .??)UF-INSTA
30: 4e 54 20 20 20 20 20 20 34 20 20 20 05 1e 00 36 NT 4 ??.6
40: 00 06 00 00 55 42 4e 54 XX XX XX XX XX XX XX XX .?..UBNTXXXXXXXX
50: 20 20 20 20 31 34 30 31 32 33 20 20 60 80 02 41 140123 `??A
[84977.840894] ath10k_snoc a000000.wifi: wmi mgmt tx queue is full
[84977.840913] ath10k_snoc a000000.wifi: failed to transmit packet, dropping: -28
[84977.840924] ath10k_snoc a000000.wifi: failed to submit frame: -28
[84977.840932] ath10k_snoc a000000.wifi: failed to transmit frame: -28
This issue is caused by race condition between skb_dequeue and
__skb_queue_tail. The queue of ‘wmi_mgmt_tx_queue’ is protected by a
different lock: ar->data_lock vs list->lock, the result is no protection.
So when ath10k_mgmt_over_wmi_tx_work() and ath10k_mac_tx_wmi_mgmt()
running concurrently on different CPUs, there appear to be a rare corner
cases when the queue length is 1,
If the instruction ‘next = skb->next’ is executed before
‘WRITE_ONCE(prev->next, newsk)’, newsk will be lost, as CPUx get the
old ‘next’ pointer, but the length is still added by one. The final
result is the length of the queue will reach the maximum value but
the queue is empty.
So remove ar->data_lock, and use 'skb_queue_tail' instead of
'__skb_queue_tail' to prevent the potential race condition. Also switch
to use skb_queue_len_lockless, in case we queue a few SKBs simultaneously.
pktgen create threads for all online cpus and bond these threads to
relevant cpu repecivtily. when this thread firstly be woken up, it
will compare cpu currently running with the cpu specified at the time
of creation and if the two cpus are not equal, BUG_ON() will take effect
causing panic on the system.
Notice that these threads could be migrated to other cpus before start
running because of the cpu hotplug after these threads have created. so the
BUG_ON() used here seems unreasonable and we can replace it with WARN_ON()
to just printf a warning other than panic the system.
In pm sleep-resume context, while the btusb device rebinds, it enters
hci_unregister_dev(), whilst there is a possibility of hdev receiving
PM_POST_SUSPEND suspend_notifier event, leading to generation of msg
frames. When hci_unregister_dev() completes, i.e. hdev context is
destroyed/freed, those intermittently sent msg frames cause memory
leak.
BUG details:
Below is stack trace of thread that enters hci_unregister_dev(), marks
the hdev flag HCI_UNREGISTER to 1, and then goes onto to wait on notifier
lock - refer unregister_pm_notifier().
Below is stack trace of thread executing hci_suspend_notifier() which
processes the PM_POST_SUSPEND event, while the unbinding thread is
waiting on lock.
We can currently get a "command execute failure 19" error on beacon loss
if the signal is weak:
wlcore: Beacon loss detected. roles:0xff
wlcore: Connection loss work (role_id: 0).
...
wlcore: ERROR command execute failure 19
...
WARNING: CPU: 0 PID: 1552 at drivers/net/wireless/ti/wlcore/main.c:803
...
(wl12xx_queue_recovery_work.part.0 [wlcore])
(wl12xx_cmd_role_start_sta [wlcore])
(wl1271_op_bss_info_changed [wlcore])
(ieee80211_prep_connection [mac80211])
Error 19 is defined as CMD_STATUS_WRONG_NESTING from the wlcore firmware,
and seems to mean that the firmware no longer wants to see the quirk
handling for WLCORE_QUIRK_START_STA_FAILS done.
This quirk got added with commit 18eab430700d ("wlcore: workaround
start_sta problem in wl12xx fw"), and it seems that this already got fixed
in the firmware long time ago back in 2012 as wl18xx never had this quirk
in place to start with.
As we no longer even support firmware that early, to me it seems that it's
safe to just drop WLCORE_QUIRK_START_STA_FAILS to fix the error. Looks
like earlier firmware got disabled back in 2013 with commit 0e284c074ef9
("wl12xx: increase minimum singlerole firmware version required").
If it turns out we still need WLCORE_QUIRK_START_STA_FAILS with any
firmware that the driver works with, we can simply revert this patch and
add extra checks for firmware version used.
With this fix wlcore reconnects properly after a beacon loss.
The constant 20 makes the font sum computation signed which can lead to
sign extensions and signed wraps. It's not much of a problem as we build
with -fno-strict-overflow. But if we ever decide not to, be ready, so
switch the constant to unsigned.
The System Controller Firmware (SCFW) is a low-level system function
which runs on a dedicated Cortex-M core to provide power, clock, and
resource management. It exists on some i.MX8 processors. e.g. i.MX8QM
(QM, QP), and i.MX8QX (QXP, DX). SCU driver manages the IPC interface
between host CPU and the SCU firmware running on M4.
For i.MX8QM, stop mode request is controlled by System Controller Unit(SCU)
firmware, this patch introduces FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW quirk
for this function.
On this system the M.2 PCIe WiFi card isn't detected after reboot, only
after cold boot. reboot=pci fixes this behavior. In [0] the same issue
is described, although on another system and with another Intel WiFi
card. In case it's relevant, both systems have Celeron CPUs.
Add a PCI reboot quirk on affected systems until a more generic fix is
available.
When fw_core_add_address_handler() fails, we need to destroy
the port by tty_port_destroy(). Also we need to unregister
the address handler by fw_core_remove_address_handler() on
failure.
It happened "Kernel panic - not syncing: hung_task: blocked tasks" when
test simulate crash and ifconfig down/rmmod meanwhile.
Test steps:
1.Test commands, either can reproduce the hang for PCIe, SDIO and SNOC.
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash;sleep 0.05;ifconfig wlan0 down
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash;rmmod ath10k_sdio
echo hw-restart > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash;rmmod ath10k_pci
2. dmesg:
[ 5622.548630] ath10k_sdio mmc1:0001:1: simulating soft firmware crash
[ 5622.655995] ieee80211 phy0: Hardware restart was requested
[ 5776.355164] INFO: task shill:1572 blocked for more than 122 seconds.
[ 5776.355687] INFO: task kworker/1:2:24437 blocked for more than 122 seconds.
[ 5776.359812] Kernel panic - not syncing: hung_task: blocked tasks
[ 5776.359836] CPU: 1 PID: 55 Comm: khungtaskd Tainted: G W 4.19.86 #137
[ 5776.359846] Hardware name: MediaTek krane sku176 board (DT)
[ 5776.359855] Call trace:
[ 5776.359868] dump_backtrace+0x0/0x170
[ 5776.359881] show_stack+0x20/0x2c
[ 5776.359896] dump_stack+0xd4/0x10c
[ 5776.359916] panic+0x12c/0x29c
[ 5776.359937] hung_task_panic+0x0/0x50
[ 5776.359953] kthread+0x120/0x130
[ 5776.359965] ret_from_fork+0x10/0x18
[ 5776.359986] SMP: stopping secondary CPUs
[ 5776.360012] Kernel Offset: 0x141ea00000 from 0xffffff8008000000
[ 5776.360026] CPU features: 0x0,2188200c
[ 5776.360035] Memory Limit: none
The test command run simulate_fw_crash firstly and it call into
ath10k_sdio_hif_stop from ath10k_core_restart, then napi_disable
is called and bit NAPI_STATE_SCHED is set. After that, function
ath10k_sdio_hif_stop is called again from ath10k_stop by command
"ifconfig wlan0 down" or "rmmod ath10k_sdio", then command blocked.
It is blocked by napi_synchronize, napi_disable will set bit with
NAPI_STATE_SCHED, and then napi_synchronize will enter dead loop
becuase bit NAPI_STATE_SCHED is set by napi_disable.
function of napi_synchronize
static inline void napi_synchronize(const struct napi_struct *n)
{
if (IS_ENABLED(CONFIG_SMP))
while (test_bit(NAPI_STATE_SCHED, &n->state))
msleep(1);
else
barrier();
}
function of napi_disable
void napi_disable(struct napi_struct *n)
{
might_sleep();
set_bit(NAPI_STATE_DISABLE, &n->state);
while (test_and_set_bit(NAPI_STATE_SCHED, &n->state))
msleep(1);
while (test_and_set_bit(NAPI_STATE_NPSVC, &n->state))
msleep(1);
The original fixed-link.txt allowed a pause property for fixed link.
This has been missed in the conversion to yaml format.
Fixes: 9d3de3c58347 ("dt-bindings: net: Add YAML schemas for the generic Ethernet options") Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/E1l6W2G-0002Ga-0O@rmk-PC.armlinux.org.uk Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_ifsioc_locked() is called with only RCU read lock, so when
there is a parallel writer changing the mac address, it could
get a partially updated mac address, as shown below:
Close this race condition by guarding them with a RW semaphore,
like netdev_get_name(). We can not use seqlock here as it does not
allow blocking. The writers already take RTNL anyway, so this does
not affect the slow path. To avoid bothering existing
dev_set_mac_address() callers in drivers, introduce a new wrapper
just for user-facing callers on ioctl and rtnetlink paths.
Note, bonding also changes slave mac addresses but that requires
a separate patch due to the complexity of bonding code.
Fixes: 3710becf8a58 ("net: RCU locking for simple ioctl()") Reported-by: "Gong, Sishuai" <sishuai@purdue.edu> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Cong Wang <cong.wang@bytedance.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the psample netlink skb is allocated with a size that does
not account for the nested 'PSAMPLE_ATTR_TUNNEL' attribute and the
padding required for the 64-bit attribute 'PSAMPLE_TUNNEL_KEY_ATTR_ID'.
This can result in failure to add attributes to the netlink skb due
to insufficient tail room. The following error message is printed to
the kernel log: "Could not create psample log message".
Fix this by adjusting the allocation size to take into account the
nested attribute and the padding.
In IEC 62439-3 EntryForgetTime is defined with a value of 400 ms. When a
node does not send any frame within this time, the sequence number check
for can be ignored. This solves communication issues with Cisco IE 2000
in Redbox mode.
Fixes: f421436a591d ("net/hsr: Add support for the High-availability Seamless Redundancy protocol (HSRv0)") Signed-off-by: Marco Wenzel <marco.wenzel@a-eberle.de> Reviewed-by: George McCollister <george.mccollister@gmail.com> Tested-by: George McCollister <george.mccollister@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210224094653.1440-1-marco.wenzel@a-eberle.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2 bytes of the MTU are reserved for Atheros DSA tag, but DSA core
has already handled that since commit dc0fe7d47f9f.
Remove the unnecessary reservation.
Support also transmitting frames using the custom "8899 A"
4 byte tag.
Qingfang came up with the solution: we need to pad the
ethernet frame to 60 bytes using eth_skb_pad(), then the
switch will happily accept frames with custom tags.
Cc: Mauri Sandberg <sandberg@mailfence.com> Reported-by: DENG Qingfang <dqfext@gmail.com> Fixes: efd7fe68f0c6 ("net: dsa: tag_rtl4_a: Implement Realtek 4 byte A tag") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looking through patchwork I don't see that there was any consensus to
use switchdev notifiers only in case of netlink provided port flags but
not sysfs (as a sort of deprecation, punishment or anything like that),
so we should probably keep the user interface consistent in terms of
functionality.
Fixes: 3922285d96e7 ("net: bridge: Add support for offloading port attributes") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the msk is closed before sending or receiving any data,
no DATA_FIN is generated, instead an MPC ack packet is
crafted out.
In the above scenario, the MPTCP protocol creates and sends a
pure ack and such packets matches also the criteria for an
MPC ack and the protocol tries first to insert MPC options,
leading to the described error.
This change addresses the issue by avoiding the insertion of an
MPC option for DATA_FIN packets or if the sub-flow is not
established.
To avoid doing multiple times the same test, fetch the data_fin
flag in a bool variable and pass it to both the interested
helpers.
Fixes: 6d0060f600ad ("mptcp: Write MPTCP DSS headers to outgoing data packets") Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MPJ subflows are not exposed as fds to user spaces. As such,
incoming MPJ subflows are removed from the accept queue by
tcp_check_req()/tcp_get_cookie_sock().
Later tcp_child_process() invokes subflow_data_ready() on the
parent socket regardless of the subflow kind, leading to poll
wakeups even if the later accept will block.
Address the issue by double-checking the queue state before
waking the user-space.
Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/164 Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Fixes: f296234c98a8 ("mptcp: Add handling of incoming MP_JOIN requests") Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tcp_rmem[1] has been changed to 131072, we should update the documentation
to reflect this.
Fixes: a337531b942b ("tcp: up initial rmem to 128KB and SYN rwin to around 64KB") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Zhibin Liu <zhibinliu@google.com> Cc: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not need to wait for REG_MR completion, so remove the
SIGNAL flag.
Fixes: 9cb837480424 ("RDMA/rtrs: server: main functionality") Link: https://lore.kernel.org/r/20201217141915.56989-18-jinpu.wang@cloud.ionos.com Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We may want to add new flags, so it's better to use bitmask to check flags.
Fixes: 6a98d71daea1 ("RDMA/rtrs: client: main functionality") Link: https://lore.kernel.org/r/20201217141915.56989-17-jinpu.wang@cloud.ionos.com Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com> Signed-off-by: Gioh Kim <gi-oh.kim@cloud.ionos.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For HB, there is no need to generate signal for completion.
Also remove a comment accordingly.
Fixes: c0894b3ea69d ("RDMA/rtrs: core: lib functions shared between client and server modules") Link: https://lore.kernel.org/r/20201217141915.56989-16-jinpu.wang@cloud.ionos.com Signed-off-by: Jack Wang <jinpu.wang@cloud.ionos.com> Reported-by: Gioh Kim <gi-oh.kim@cloud.ionos.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
follow_pfn() doesn't make sure that we're using the correct page
protections, get the pte with follow_pte() so that we can test
protections and get the pfn from the pte.
Fixes: 5cbf3264bc71 ("vfio/type1: Fix VA->PA translation for PFNMAP VMAs in vaddr_get_pfn()") Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Cornelia Huck <cohuck@redhat.com> Reviewed-by: Peter Xu <peterx@redhat.com> Signed-off-by: Alex Williamson <alex.williamson@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code would unnecessarily expand the address range. Consider
one example, (start, end) = (1G-2M, 3G+2M), and (vm_start, vm_end) =
(1G-4M, 3G+4M), the expected adjustment should be keep (1G-2M, 3G+2M)
without expand. But the current result will be (1G-4M, 3G+4M). Actually,
the range (1G-4M, 1G) and (3G, 3G+4M) would never been involved in pmd
sharing.
After this patch, we will check that the vma span at least one PUD aligned
size and the start,end range overlap the aligned range of vma.
With above example, the aligned vma range is (1G, 3G), so if (start, end)
range is within (1G-4M, 1G), or within (3G, 3G+4M), then no adjustment to
both start and end. Otherwise, we will have chance to adjust start
downwards or end upwards without exceeding (vm_start, vm_end).
Mike:
: The 'adjusted range' is used for calls to mmu notifiers and cache(tlb)
: flushing. Since the current code unnecessarily expands the range in some
: cases, more entries than necessary would be flushed. This would/could
: result in performance degradation. However, this is highly dependent on
: the user runtime. Is there a combination of vma layout and calls to
: actually hit this issue? If the issue is hit, will those entries
: unnecessarily flushed be used again and need to be unnecessarily reloaded?
Link: https://lkml.kernel.org/r/20210104081631.2921415-1-lixinhai.lxh@gmail.com Fixes: 75802ca66354 ("mm/hugetlb: fix calculation of adjust_range_if_pmd_sharing_possible") Signed-off-by: Li Xinhai <lixinhai.lxh@gmail.com> Suggested-by: Mike Kravetz <mike.kravetz@oracle.com> Reviewed-by: Mike Kravetz <mike.kravetz@oracle.com> Cc: Peter Xu <peterx@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There exists a race where we can be attempting to create a new nbd
configuration while a previous configuration is going down, both
configured with DESTROY_ON_DISCONNECT. Normally devices all have a
reference of 1, as they won't be cleaned up until the module is torn
down. However with DESTROY_ON_DISCONNECT we'll make sure that there is
only 1 reference (generally) on the device for the config itself, and
then once the config is dropped, the device is torn down.
The race that exists looks like this
TASK1 TASK2
nbd_genl_connect()
idr_find()
refcount_inc_not_zero(nbd)
* count is 2 here ^^
nbd_config_put()
nbd_put(nbd) (count is 1)
setup new config
check DESTROY_ON_DISCONNECT
put_dev = true
if (put_dev) nbd_put(nbd)
* free'd here ^^
In nbd_genl_connect() we assume that the nbd ref count will be 2,
however clearly that won't be true if the nbd device had been setup as
DESTROY_ON_DISCONNECT with its prior configuration. Fix this by getting
rid of the runtime flag to check if we need to mess with the nbd device
refcount, and use the device NBD_DESTROY_ON_DISCONNECT flag to check if
we need to adjust the ref counts. This was reported by syzkaller with
the following kasan dump
BUG: KASAN: use-after-free in instrument_atomic_read include/linux/instrumented.h:71 [inline]
BUG: KASAN: use-after-free in atomic_read include/asm-generic/atomic-instrumented.h:27 [inline]
BUG: KASAN: use-after-free in refcount_dec_not_one+0x71/0x1e0 lib/refcount.c:76
Read of size 4 at addr ffff888143bf71a0 by task systemd-udevd/8451
At early boot stage, we have a whole PGDIR to map the kernel, so there
is no need to restrict the early mapping size to 128MB. Removing this
define also allows us to simplify some compile time logic.
This fixes large kernel mappings with a size greater than 128MB, as it
is the case for syzbot kernels whose size was just ~130MB.
Note that on rv64, for now, we are then limited to PGDIR size for early
mapping as we can't use PGD mappings (see [1]). That should be enough
given the relative small size of syzbot kernels compared to PGDIR_SIZE
which is 1GB.
The mptcp_worker tries to update the MPTCP retransmission timer
even if such timer is not currently scheduled.
The mptcp_rtx_head() return value is bogus: we can have enqueued
data not yet transmitted. The above may additionally cause spurious,
unneeded MPTCP-level retransmissions.
Fix the issue adding an explicit clearing of the rtx queue before
trying to retransmit and checking for unacked data.
Additionally drop an unneeded timer stop call and the unused
mptcp_rtx_tail() helper.
Reported-by: Christoph Paasch <cpaasch@apple.com> Fixes: 6e628cd3a8f7 ("mptcp: use mptcp release_cb for delayed tasks") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid the assumption that ksize(kmalloc(S)) == ksize(kmalloc(S)): when
cloning an skb, save and restore truesize after pskb_expand_head(). This
can occur if the allocator decides to service an allocation of the same
size differently (e.g. use a different size class, or pass the
allocation on to KFENCE).
Because truesize is used for bookkeeping (such as sk_wmem_queued), a
modified truesize of a cloned skb may result in corrupt bookkeeping and
relevant warnings (such as in sk_stream_kill_queues()).
syzbot is reporting that tomoyo's quota check is racy [1]. But this check
is tolerant of some degree of inaccuracy. Thus, teach KCSAN to ignore
this data race.
syzbot found WARNINGs in several smackfs write operations where
bytes count is passed to memdup_user_nul which exceeds
GFP MAX_ORDER. Check count size if bigger than PAGE_SIZE.
Per smackfs doc, smk_write_net4addr accepts any label or -CIPSO,
smk_write_net6addr accepts any label or -DELETE. I couldn't find
any general rule for other label lengths except SMK_LABELLEN,
SMK_LONGLABEL, SMK_CIPSOMAX which are documented.
Let's constrain, in general, smackfs label lengths for PAGE_SIZE.
Although fuzzer crashes write to smackfs/netlabel on 0x400000 length.
Here is a quick way to reproduce the WARNING:
python -c "print('A' * 0x400000)" > /sys/fs/smackfs/netlabel
An assert failure is triggered by syzkaller test due to
ATTR_KILL_PRIV is not cleared before xfs_setattr_size.
As ATTR_KILL_PRIV is not checked/used by xfs_setattr_size,
just remove it from the assert.
Signed-off-by: Yumei Huang <yuhuang@redhat.com> Reviewed-by: Brian Foster <bfoster@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Darrick J. Wong <djwong@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot discovered that the probe error handling doesn't clean up the
resources allocated in zr364xx_board_init(). There are several
related bugs in this code so I have re-written the error handling.
1) Introduce a new function zr364xx_board_uninit() which cleans up
the resources in zr364xx_board_init().
2) In zr364xx_board_init() if the call to zr364xx_start_readpipe()
fails then release the "cam->buffer.frame[i].lpvbits" memory
before returning. This way every function either allocates
everything successfully or it cleans up after itself.
3) Re-write the probe function so that each failure path goto frees
the most recent allocation. That way we don't free anything
before it has been allocated and we can also verify that
everything is freed.
4) Originally, in the probe function the "cam->v4l2_dev.release"
pointer was set to "zr364xx_release" near the start but I moved
that assignment to the end, after everything had succeeded. The
release function was never actually called during the probe cleanup
process, but with this change I wanted to make it clear that we
don't want to call zr364xx_release() until everything is
allocated successfully.
Next I re-wrote the zr364xx_release() function. Ideally this would
have been a simple matter of copy and pasting the cleanup code from
probe and adding an additional call to video_unregister_device(). But
there are a couple quirks to note.
1) The probe function does not call videobuf_mmap_free() and I don't
know where the videobuf_mmap is allocated. I left the code as-is to
avoid introducing a bug in code I don't understand.
2) The zr364xx_board_uninit() has a call to zr364xx_stop_readpipe()
which is a change from the original behavior with regards to
unloading the driver. Calling zr364xx_stop_readpipe() on a stopped
pipe is not a problem so this is safe and is potentially a bugfix.
Reported-by: syzbot+b4d54814b339b5c6bbd4@syzkaller.appspotmail.com Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dlfb_alloc_urb_list function is called in dlfb_usb_probe function,
after that if an error occurs, the dlfb_free_urb_list function need to
be called.
The try_invoke_on_locked_down_task() function currently requires
that interrupts be enabled, but it is called with interrupts
disabled from rcu_print_task_stall(), resulting in an "IRQs not
enabled as expected" diagnostic. This commit therefore updates
try_invoke_on_locked_down_task() to use raw_spin_lock_irqsave() instead
of raw_spin_lock_irq(), thus allowing use from either context.
projects / linux-stable / log