This problem was reported on a SVM guest while executing kexec.
Kexec fails to load the new kernel when the PCID feature is enabled.
When kexec starts loading the new kernel, it starts the process by
resetting the vCPU's and then bringing each vCPU online one by one.
The vCPU reset is supposed to reset all the register states before the
vCPUs are brought online. However, the CR4 register is not reset during
this process. If this register is already setup during the last boot,
all the flags can remain intact. The X86_CR4_PCIDE bit can only be
enabled in long mode. So, it must be enabled much later in SMP
initialization. Having the X86_CR4_PCIDE bit set during SMP boot can
cause a boot failures.
Fix the issue by resetting the CR4 register in init_vmcb().
The Acer Aspire Switch 10E (SW3-016)'s keyboard-dock uses the same USB-ids
as the Acer One S1003 keyboard-dock. Yet they are not entirely the same:
1. The S1003 keyboard-dock has the same report descriptors as the
S1002 keyboard-dock (which has different USB-ids)
2. The Acer Aspire Switch 10E's keyboard-dock has different
report descriptors from the S1002/S1003 keyboard docks and it
sends 0x00880078 / 0x00880079 usage events when the touchpad is
toggled on/off (which is handled internally).
This means that all Acer kbd-docks handled by the hid-ite.c drivers
report their touchpad being toggled on/off through these custom
usage-codes with the exception of the S1003 dock, which likely is
a bug of that dock.
Add a QUIRK_TOUCHPAD_ON_OFF_REPORT quirk for the Aspire Switch 10E / S1003
usb-id so that the touchpad toggling will get reported to userspace on
the Aspire Switch 10E.
Since the Aspire Switch 10E's kbd-dock has different report-descriptors,
this also requires adding support for fixing those to ite_report_fixup().
Setting the quirk will also cause ite_report_fixup() to hit the
S1002/S1003 descriptors path on the S1003. Since the S1003 kbd-dock
never generates any input-reports for the fixed up part of the
descriptors this does not matter; and if there are versions out there
which do actually send input-reports for the touchpad-toggle then the
fixup should actually help to make things work.
This was tested on both an Acer Aspire Switch 10E and on an Acer One S1003.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit adds mixer quirks for the Pioneer DJM-900NXS2 mixer. This
device has 6 capture channels, 5 of them allow setting the signal
source. This adds controls for these, similar to the DJM-250Mk2.
However, playpack channels are not controllable via software like on the
250Mk2, as they can only be set manually on the mixing console.
Read-only controls showing the currently selected playback channels are
omitted.
This allows for N different devices to use the pioneer mixer quirk for
setting capture/record type and recording level. The impementation has
not changed much with the exception of an additional mask on
private_value to allow storing of a device index:
DEVICE MASK 0xff000000
GROUP_MASK 0x00ff0000
VALUE_MASK 0x0000ffff
This could be improved by changing the arrays of wValues for each
channel to contain named definitions (e.g. SND_DJM_CAP_LINE). It would
improve readability and perhaps would allow using the same array for
multiple channels. The channel number can be specified on the control
next to the wIndex.
Feedback is very much appreciated as I'm not the most proficient C
programmer but am learning as I go.
The PC_DBG_ECO_CNTL register on the Adreno A5xx family gets
programmed to some different values on a per-model basis.
At least, this is what we intend to do here;
Unfortunately, though, this register is being overwritten with a
static magic number, right after applying the GPU-specific
configuration (including the GPU-specific quirks) and that is
effectively nullifying the efforts.
Let's remove the redundant and wrong write to the PC_DBG_ECO_CNTL
register in order to retain the wanted configuration for the
target GPU.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org> Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org> Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Exynos needs scatterlist entries aligned to page size because it isn't
capable of transferring data contained in one DATA IN operation to seversal
areas in memory.
Some SoCs require a single scatterlist entry for smaller than page size,
i.e. 4KB. When dispatching commands with more than one scatterlist entry
under 4KB in size the following behavior is observed:
A command to read a block range is dispatched with two scatterlist entries
that are named AAA and BBB. After dispatching, the host builds two PRDT
entries and during transmission, device sends just one DATA IN because
device doesn't care about host DMA. The host then transfers the combined
amount of data from start address of the area named AAA. As a consequence,
the area that follows AAA in memory would be corrupted.
A dummy zero bit is sent preceding the data during a read transfer by the
Microchip 93LC46B eeprom (section 2.7 of[1]). This results in right shift
of data during a read. In order to ignore this bit a quirk can be added to
send an extra zero bit after the read address.
Add a quirk to ignore the zero bit sent before data by adding a zero bit
after the read address.
The UniPro specification states that attribute IDs of the following
parameters are vendor-specific so some SoCs could have no regions at the
defined addresses:
Flush during hibern8 is sufficient on MediaTek platforms, thus enable
UFSHCI_QUIRK_SKIP_MANUAL_WB_FLUSH_CTRL to skip enabling
fWriteBoosterBufferFlush during WriteBooster initialization.
increase_address_space() calls get_zeroed_page(gfp) under spin_lock with
disabled interrupts. gfp flags passed to increase_address_space() may allow
sleeping, so it comes to this:
BUG: sleeping function called from invalid context at mm/page_alloc.c:4342
in_atomic(): 1, irqs_disabled(): 1, pid: 21555, name: epdcbbf1qnhbsd8
Calling btrfs_qgroup_reserve_meta_prealloc from
btrfs_delayed_inode_reserve_metadata can result in flushing delalloc
while holding a transaction and delayed node locks. This is deadlock
prone. In the past multiple commits:
* ae5e070eaca9 ("btrfs: qgroup: don't try to wait flushing if we're
already holding a transaction")
* 6f23277a49e6 ("btrfs: qgroup: don't commit transaction when we already
hold the handle")
Tried to solve various aspects of this but this was always a
whack-a-mole game. Unfortunately those 2 fixes don't solve a deadlock
scenario involving btrfs_delayed_node::mutex. Namely, one thread
can call btrfs_dirty_inode as a result of reading a file and modifying
its atime:
To fully address those cases the complete fix is to never issue any
flushing while holding the transaction or the delayed node lock. This
patch achieves it by calling qgroup_reserve_meta directly which will
either succeed without flushing or will fail and return -EDQUOT. In the
latter case that return value is going to be propagated to
btrfs_dirty_inode which will fallback to start a new transaction. That's
fine as the majority of time we expect the inode will have
BTRFS_DELAYED_NODE_INODE_DIRTY flag set which will result in directly
copying the in-memory state.
Fixes: c53e9653605d ("btrfs: qgroup: try to flush qgroup space when we get -EDQUOT") CC: stable@vger.kernel.org # 5.10+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to commit 28187dc8ebd9 ("ARM: 9025/1: Kconfig: CPU_BIG_ENDIAN
depends on !LD_IS_LLD"), ld.lld prior to 13.0.0 does not properly
support aarch64 big endian, leading to the following build error when
CONFIG_CPU_BIG_ENDIAN is selected:
ld.lld: error: unknown emulation: aarch64linuxb
This has been resolved in LLVM 13. To avoid errors like this, only allow
CONFIG_CPU_BIG_ENDIAN to be selected if using ld.bfd or ld.lld 13.0.0
and newer.
While we are here, the indentation of this symbol used spaces since its
introduction in commit a872013d6d03 ("arm64: kconfig: allow
CPU_BIG_ENDIAN to be selected"). Change it to tabs to be consistent with
kernel coding style.
The kernel test robot reported multiple linkage problems like this:
hppa64-linux-ld: init/main.o(.init.text+0x56c): cannot reach printk
init/main.o: in function `unknown_bootoption':
(.init.text+0x56c): relocation truncated to fit: R_PARISC_PCREL22F against
symbol `printk' defined in .text.unlikely section in kernel/printk/printk.o
There are two ways to solve it:
a) Enable the -mlong-call compiler option (CONFIG_MLONGCALLS),
b) Add long branch stub support in 64-bit linker.
While b) is the long-term solution, this patch works around the issue by
automatically enabling the CONFIG_MLONGCALLS option when
CONFIG_COMPILE_TEST is set, which indicates that a non-production kernel
(e.g. 0-day kernel) is built.
My 2TB SKC2000 showed the exact same symptoms that were provided
in 538e4a8c57 ("nvme-pci: avoid the deepest sleep state on
Kingston A2000 SSDs"), i.e. a complete NVME lockup that needed
cold boot to get it back.
According to some sources, the A2000 is simply a rebadged
SKC2000 with a slightly optimized firmware.
Adding the SKC2000 PCI ID to the quirk list with the same workaround
as the A2000 made my laptop survive a 5 hours long Yocto bootstrap
buildfest which reliably triggered the SSD lockup previously.
Signed-off-by: Zoltán Böszörményi <zboszor@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to v4l2 request api specifications, it's allowed to skip
control if its content isn't changed for performance reasons. Cedrus
driver predates that, so it has implemented mechanism to check if all
required controls are included in one request.
Conform to specifications with removing that mechanism.
Note that this mechanism with static required flag isn't very good
anyway because need for control is usually signaled in other controls.
[ 97.866748] a.out/2890 is trying to acquire lock:
[ 97.867829] ffff8881046763e8 (&ctx->uring_lock){+.+.}-{3:3}, at:
io_wq_submit_work+0x155/0x240
[ 97.869735]
[ 97.869735] but task is already holding lock:
[ 97.871033] ffff88810dfe0be8 (&ctx->uring_lock){+.+.}-{3:3}, at:
__x64_sys_io_uring_enter+0x3f0/0x5b0
[ 97.873074]
[ 97.873074] other info that might help us debug this:
[ 97.874520] Possible unsafe locking scenario:
[ 97.874520]
[ 97.875845] CPU0
[ 97.876440] ----
[ 97.877048] lock(&ctx->uring_lock);
[ 97.877961] lock(&ctx->uring_lock);
[ 97.878881]
[ 97.878881] *** DEADLOCK ***
[ 97.878881]
[ 97.880341] May be due to missing lock nesting notation
[ 97.880341]
[ 97.881952] 1 lock held by a.out/2890:
[ 97.882873] #0: ffff88810dfe0be8 (&ctx->uring_lock){+.+.}-{3:3}, at:
__x64_sys_io_uring_enter+0x3f0/0x5b0
[ 97.885108]
[ 97.885108] stack backtrace:
[ 97.890457] Call Trace:
[ 97.891121] dump_stack+0xac/0xe3
[ 97.891972] __lock_acquire+0xab6/0x13a0
[ 97.892940] lock_acquire+0x2c3/0x390
[ 97.894894] __mutex_lock+0xae/0x9f0
[ 97.901101] io_wq_submit_work+0x155/0x240
[ 97.902112] io_wq_cancel_cb+0x162/0x490
[ 97.904126] io_async_find_and_cancel+0x3b/0x140
[ 97.905247] io_issue_sqe+0x86d/0x13e0
[ 97.909122] __io_queue_sqe+0x10b/0x550
[ 97.913971] io_queue_sqe+0x235/0x470
[ 97.914894] io_submit_sqes+0xcce/0xf10
[ 97.917872] __x64_sys_io_uring_enter+0x3fb/0x5b0
[ 97.921424] do_syscall_64+0x2d/0x40
[ 97.922329] entry_SYSCALL_64_after_hwframe+0x44/0xa9
While holding uring_lock, e.g. from inline execution, async cancel
request may attempt cancellations through io_wq_submit_work, which may
try to grab a lock. Delay it to task_work, so we do it from a clean
context and don't have to worry about locking.
Cc: <stable@vger.kernel.org> # 5.5+ Fixes: c07e6719511e ("io_uring: hold uring_lock while completing failed polled io in io_wq_submit_work()") Reported-by: Abaci <abaci@linux.alibaba.com> Reported-by: Hao Xu <haoxu@linux.alibaba.com> Signed-off-by: Pavel Begunkov <asml.silence@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Saving one lock/unlock for io-wq is not super important, but adds some
ugliness in the code. More important, atomic decs not turning it to zero
for some archs won't give the right ordering/barriers so the
io_steal_work() may pretty easily get subtly and completely broken.
Return back 2-step io-wq work exchange and clean it up.
We currently split the close into two, in case we have a ->flush op
that we can't safely handle from non-blocking context. This requires
us to flag the op as uncancelable if we do need to punt it async, and
that means special handling for just this op type.
Use __close_fd_get_file() and grab the files lock so we can get the file
and check if we need to go async in one atomic operation. That gets rid
of the need for splitting this into two steps, and hence the need for
IO_WQ_WORK_NO_CANCEL.
We park SQPOLL task before going into io_uring_cancel_files(), so the
task won't run task_works including those that might be important for
the cancellation passes. In this case it's io_poll_remove_one(), which
frees requests via io_put_req_deferred().
Unpark it for while waiting, it's ok as we disable submissions
beforehand, so no new requests will be generated.
Files and task cancellations go over same steps trying to cancel
requests in io-wq, poll, etc. Deduplicate it with a helper.
note: new io_uring_try_cancel_requests() is former
__io_uring_cancel_task_requests() with files passed as an agrument and
flushing overflowed requests.
The handling of the generic_serial_bus (I2C) and GPIO op_regions in
acpi_ev_address_space_dispatch() passes a number of extra parameters
to the address-space handler through the address-space Context pointer
(instead of using more function parameters).
The Context is shared between threads, so if multiple threads try to
call the handler for the same address-space at the same time, then
a second thread could change the parameters of a first thread while
the handler is running for the first thread.
An example of this race hitting is the Lenovo Yoga Tablet2 1015L,
where there are both attrib_bytes accesses and attrib_byte accesses
to the same address-space. The attrib_bytes access stores the number
of bytes to transfer in Context->access_length. Where as for the
attrib_byte access the number of bytes to transfer is always 1 and
field_obj->Field.access_length is unused (so 0). Both types of
accesses racing from different threads leads to the following problem:
1. Thread a. starts an attrib_bytes access, stores a non 0 value
from field_obj->Field.access_length in Context->access_length
2. Thread b. starts an attrib_byte access, stores 0 in
Context->access_length
3. Thread a. calls i2c_acpi_space_handler() (under Linux). Which
sees that the access-type is ACPI_GSB_ACCESS_ATTRIB_MULTIBYTE
and calls acpi_gsb_i2c_read_bytes(..., Context->access_length)
4. At this point Context->access_length is 0 (set by thread b.)
rather then the field_obj->Field.access_length value from thread a.
This 0 length reads leads to the following errors being logged:
i2c i2c-0: adapter quirk: no zero length (addr 0x0078, size 0, read)
i2c i2c-0: i2c read 0 bytes from client@0x78 starting at reg 0x0 failed, error: -95
Note this is just an example of the problems which this race can cause.
There are likely many more (sporadic) problems caused by this race.
This commit adds a new context_mutex to struct acpi_object_addr_handler
and makes acpi_ev_address_space_dispatch() take that mutex when
using the shared Context to pass extra parameters to an address-space
handler, fixing this race.
Note the new mutex must be taken *after* exiting the interpreter,
therefor the existing acpi_ex_exit_interpreter() call is moved to above
the code which stores the extra parameters in the Context.
Link: https://github.com/acpica/acpica/commit/c9e01169 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Bob Moore <robert.moore@intel.com> Signed-off-by: Erik Kaneda <erik.kaneda@intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Armin reported that after referenced commit his RTL8105e is dead when
resuming from suspend and machine runs on battery. This patch has been
confirmed to fix the issue.
Fixes: e80bd76fbf56 ("r8169: work around power-saving bug on some chip versions") Reported-by: Armin Wolf <W_Armin@gmx.de> Tested-by: Armin Wolf <W_Armin@gmx.de> Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit db68ce10c4f0a27c ("new helper: uaccess_kernel()") replaced
segment_eq(get_fs(), KERNEL_DS) with uaccess_kernel(). But the correct
method for tomoyo to check whether current is a kernel thread in order
to assume that kernel threads are privileged for socket operations was
(current->flags & PF_KTHREAD). Now that uaccess_kernel() became 0 on x86,
tomoyo has to fix this problem. Do like commit 942cb357ae7d9249 ("Smack:
Handle io_uring kernel thread privileges") does.
We need to use sector_t for zone_sectors, or it would set the zone size
to zero when the size >= 4GB (= 2^24 sectors) by shifting the
zone_sectors value by SECTOR_SHIFT. We're assuming zones sizes up to
8GiB.
Fixes: 5b316468983d ("btrfs: get zone information of zoned block devices") Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As per Intel vt-d spec, Rev 3.0 (section 10.4.45 "Virtual Command Response
Register"), the status code of "No PASID available" error in response to
the Allocate PASID command is 2, not 1. The same for "Invalid PASID" error
in response to the Free PASID command.
We will otherwise see confusing kernel log under the command failure from
guest side. Fix it.
The lazy IOTLB flushing setup leaves a time window, in which the device
can still access some system memory, which has already been unmapped by
the device driver. It's not suitable for untrusted devices. A malicious
device might use this to attack the system by obtaining data that it
shouldn't obtain.
Fixes: c588072bba6b5 ("iommu/vt-d: Convert intel iommu driver to the iommu ops") Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20210225061454.2864009-1-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 25938c73cd79 ("iommu/tegra-smmu: Rework tegra_smmu_probe_device()")
removed certain hack in the tegra_smmu_probe() by relying on IOMMU core to
of_xlate SMMU's SID per device, so as to get rid of tegra_smmu_find() and
tegra_smmu_configure() that are typically done in the IOMMU core also.
This approach works for both existing devices that have DT nodes and other
devices (like PCI device) that don't exist in DT, on Tegra210 and Tegra3
upon testing. However, Page Fault errors are reported on tegra124-Nyan:
After debugging, I found that the mentioned commit changed some function
callback sequence of tegra-smmu's, resulting in enabling SMMU for display
client before display driver gets initialized. I couldn't reproduce exact
same issue on Tegra210 as Tegra124 (arm-32) differs at arch-level code.
Actually this Page Fault is a known issue, as on most of Tegra platforms,
display gets enabled by the bootloader for the splash screen feature, so
it keeps filling the framebuffer memory. A proper fix to this issue is to
1:1 linear map the framebuffer memory to IOVA space so the SMMU will have
the same address as the physical address in its page table. Yet, Thierry
has been working on the solution above for a year, and it hasn't merged.
Therefore, let's partially revert the mentioned commit to fix the errors.
The reason why we do a partial revert here is that we can still set priv
in ->of_xlate() callback for PCI devices. Meanwhile, devices existing in
DT, like display, will go through tegra_smmu_configure() at the stage of
bus_set_iommu() when SMMU gets probed(), as what it did before we merged
the mentioned commit.
Once we have the linear map solution for framebuffer memory, this change
can be cleaned away.
[Big thank to Guillaume who reported and helped debugging/verification]
The copy_to_user() function returns the number of bytes remaining but
we want to return -EFAULT to the user if it can't complete the copy.
The "st" variable only holds zero on success or negative error codes on
failure so the type should be int.
Fixes: 36f988e978f8 ("rsxx: Adding in debugfs entries.") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
Sergei and John both reported that ia64 failed to boot in 5.11, and it
was related to signals. Turns out the ia64 signal handling is a bit odd,
it doesn't check the return value of get_signal() for whether there's a
signal to deliver or not. With the introduction of TIF_NOTIFY_SIGNAL,
then task_work could trigger it.
Fix it by only calling handle_signal() if we actually have a real signal
to deliver. This brings it in line with all other archs, too.
Fixes: b269c229b0e8 ("ia64: add support for TIF_NOTIFY_SIGNAL") Reported-by: Sergei Trofimovich <slyich@gmail.com> Reported-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de> Tested-by: Sergei Trofimovich <slyich@gmail.com> Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
On little endian system, Use aarch64_be(gcc v7.3) downloaded from
linaro.org to build image with CONFIG_CPU_BIG_ENDIAN = y,
CONFIG_FTRACE = y, CONFIG_DYNAMIC_FTRACE = y.
gcc will create symbols of _mcount but recordmcount can not create
mcount_loc for *.o.
aarch64_be-linux-gnu-objdump -r fs/namei.o | grep mcount 00000000000000d0 R_AARCH64_CALL26 _mcount
... 0000000000007190 R_AARCH64_CALL26 _mcount
The reason is than funciton arm64_is_fake_mcount can not work correctly.
A symbol of _mcount in *.o compiled with big endian compiler likes:
00 00 00 2d 00 00 01 1b
w(rp->r_info) will return 0x2d instead of 0x011b. Because w() takes
uint32_t as parameter, which truncates rp->r_info.
Use w8() instead w() to read relp->r_info
Link: https://lkml.kernel.org/r/20210222135840.56250-1-chenjun102@huawei.com Fixes: ea0eada45632 ("recordmcount: only record relocation of type R_AARCH64_CALL26 on arm64.") Acked-by: Will Deacon <will@kernel.org> Signed-off-by: Chen Jun <chenjun102@huawei.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Multiple bug reports report issues with the SOF and SST drivers when
dealing with single microphone cases.
We currently read the DMIC array information unconditionally but we
don't check that the configuration type is actually a mic array.
When the DMIC link does not rely on a mic array configuration, the
recommendation is to check the format information to infer the maximum
number of channels, and map this to the number of microphones.
This leaves a potential for a mismatch between actual microphones
available in hardware and what the ACPI table contains, but we have no
other source of information.
Note that single microphone configurations can alternatively be
handled with a 'mic array' configuration along with a 'vendor-defined'
geometry.
Currently the mask operation on variable conf is just 3 bits so
the switch statement case value of 8 is unreachable dead code.
The function daio_mgr_dao_init can be passed a 4 bit value,
function dao_rsc_init calls it with conf set to:
conf = (desc->msr & 0x7) | (desc->passthru << 3);
so clearly when desc->passthru is set to 1 then conf can be
at least 8.
Unlike many other structure types defined in the crypto API, the
'shash_desc' structure is permitted to live on the stack, which
implies its contents may not be accessed by DMA masters. (This is
due to the fact that the stack may be located in the vmalloc area,
which requires a different virtual-to-physical translation than the
one implemented by the DMA subsystem)
Our definition of CRYPTO_MINALIGN_ATTR is based on ARCH_KMALLOC_MINALIGN,
which may take DMA constraints into account on architectures that support
non-cache coherent DMA such as ARM and arm64. In this case, the value is
chosen to reflect the largest cacheline size in the system, in order to
ensure that explicit cache maintenance as required by non-coherent DMA
masters does not affect adjacent, unrelated slab allocations. On arm64,
this value is currently set at 128 bytes.
This means that applying CRYPTO_MINALIGN_ATTR to struct shash_desc is both
unnecessary (as it is never used for DMA), and undesirable, given that it
wastes stack space (on arm64, performing the alignment costs 112 bytes in
the worst case, and the hole between the 'tfm' and '__ctx' members takes
up another 120 bytes, resulting in an increased stack footprint of up to
232 bytes.) So instead, let's switch to the minimum SLAB alignment, which
does not take DMA constraints into account.
Optional Forward Error Correction (FEC) code in dm-verity uses
Reed-Solomon code and should support roots from 2 to 24.
The error correction parity bytes (of roots lengths per RS block) are
stored on a separate device in sequence without any padding.
Currently, to access FEC device, the dm-verity-fec code uses dm-bufio
client with block size set to verity data block (usually 4096 or 512
bytes).
Because this block size is not divisible by some (most!) of the roots
supported lengths, data repair cannot work for partially stored parity
bytes.
This fix changes FEC device dm-bufio block size to "roots << SECTOR_SHIFT"
where we can be sure that the full parity data is always available.
(There cannot be partial FEC blocks because parity must cover whole
sectors.)
Because the optional FEC starting offset could be unaligned to this
new block size, we have to use dm_bufio_set_sector_offset() to
configure it.
The problem is easily reproduced using veritysetup, e.g. for roots=13:
# create an erasure that should be always repairable with this roots setting
dd if=/dev/zero of=data.img conv=notrunc bs=1 count=8 seek=4088 status=none
# try to read it through dm-verity
veritysetup open data.img test hash.img --fec-device=fec.img --fec-roots=13 $(cat roothash)
dd if=/dev/mapper/test of=/dev/null bs=4096 status=noxfer
# wait for possible recursive recovery in kernel
udevadm settle
veritysetup close test
With this fix, errors are properly repaired.
device-mapper: verity-fec: 7:1: FEC 0: corrected 8 errors
...
Without it, FEC code usually ends on unrecoverable failure in RS decoder:
device-mapper: verity-fec: 7:1: FEC 0: failed to correct: -74
...
This problem is present in all kernels since the FEC code's
introduction (kernel 4.5).
It is thought that this problem is not visible in Android ecosystem
because it always uses a default RS roots=2.
Depends-on: a14e5ec66a7a ("dm bufio: subtract the number of initial sectors in dm_bufio_get_device_size") Signed-off-by: Milan Broz <gmazyland@gmail.com> Tested-by: Jérôme Carretero <cJ-ko@zougloub.eu> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Cc: stable@vger.kernel.org # 4.5+ Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dm_bufio_get_device_size returns the device size in blocks. Before
returning the value, we must subtract the nubmer of starting
sectors. The number of starting sectors may not be divisible by block
size.
Note that currently, no target is using dm_bufio_set_sector_offset and
dm_bufio_get_device_size simultaneously, so this change has no effect.
However, an upcoming dm-verity-fec fix needs this change.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Reviewed-by: Milan Broz <gmazyland@gmail.com> Cc: stable@vger.kernel.org Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
which is due to the driver doing poll_wait() twice on the same
wait_queue_head. That is perfectly valid, but from checking the rest
of the kernel tree, it's the only driver that does this.
We can handle this just fine, we just need to ignore the second addition
as we'll get woken just fine on the first one.
Part of the logic of the new time stamp code depends on the before_stamp and
the write_stamp to be different if the write_stamp does not match the last
event on the buffer, as it will be used to calculate the delta of the next
event written on the buffer.
The discard logic depends on this, as the next event to come in needs to
inject a full timestamp as it can not rely on the last event timestamp in
the buffer because it is unknown due to events after it being discarded. But
by changing the write_stamp back to the time before it, it forces the next
event to use a full time stamp, instead of relying on it.
The issue came when a full time stamp was used for the event, and
rb_time_delta() returns zero in that case. The update to the write_stamp
(which subtracts delta) made it not change. Then when the event is removed
from the buffer, because the before_stamp and write_stamp still match, the
next event written would calculate its delta from the write_stamp, but that
would be wrong as the write_stamp is of the time of the event that was
discarded.
In the case that the delta change being made to write_stamp is zero, set the
before_stamp to zero as well, and this will force the next event to inject a
full timestamp and not use the current write_stamp.
Cc: stable@vger.kernel.org Fixes: a389d86f7fd09 ("ring-buffer: Have nested events still record running time stamp") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because the PM-runtime status of the device is not updated in
__rpm_callback(), attempts to suspend the suppliers of the given
device triggered by rpm_put_suppliers() called by it may fail.
Fix this by making __rpm_callback() update the device's status to
RPM_SUSPENDED before calling rpm_put_suppliers() if the current
status of the device is RPM_SUSPENDING and the callback just invoked
by it has returned 0 (success).
While at it, modify the code in __rpm_callback() to always check
the device's PM-runtime status under its PM lock.
Link: https://lore.kernel.org/linux-pm/CAPDyKFqm06KDw_p8WXsM4dijDbho4bb6T4k50UqqvR1_COsp8g@mail.gmail.com/ Fixes: 21d5c57b3726 ("PM / runtime: Use device links") Reported-by: Elaine Zhang <zhangqing@rock-chips.com> Diagnosed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Tested-by: Elaine Zhang <zhangiqng@rock-chips.com> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Cc: 4.10+ <stable@vger.kernel.org> # 4.10+ Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we have smack enabled, during the creation of a directory smack may
attempt to add a "smack transmute" xattr on the inode, which results in
the following warning and trace:
This happens because at btrfs_mkdir() we call d_instantiate_new() while
holding a transaction handle, which results in the following call chain:
btrfs_mkdir()
trans = btrfs_start_transaction(root, 5);
d_instantiate_new()
smack_d_instantiate()
__vfs_setxattr()
btrfs_setxattr_trans()
btrfs_start_transaction()
start_transaction()
WARN_ON()
--> a tansaction start has TRANS_EXTWRITERS
set in its type
h->orig_rsv = h->block_rsv
h->block_rsv = NULL
btrfs_end_transaction(trans)
Besides the warning triggered at start_transaction, we set the handle's
block_rsv to NULL which may cause some surprises later on.
So fix this by making btrfs_setxattr_trans() not start a transaction when
we already have a handle on one, stored in current->journal_info, and use
that handle. We are good to use the handle because at btrfs_mkdir() we did
reserve space for the xattr and the inode item.
If btrfs_qgroup_reserve_data returns an error (i.e quota limit reached)
the handling logic directly goes to the 'out' label without first
unlocking the extent range between lockstart, lockend. This results in
deadlocks as other processes try to lock the same extent.
Fixes: a7f8b1c2ac21 ("btrfs: file: reserve qgroup space after the hole punch range is locked") CC: stable@vger.kernel.org # 5.10+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The intended logic of the check is to catch cases where the desired
free_space_tree setting doesn't match the mounted setting, and the
remount is anything but ro->rw. However, it makes the mistake of
checking equality on a masked integer (btrfs_test_opt) against a boolean
(btrfs_fs_compat_ro).
If you run the reproducer:
$ mount -o space_cache=v2 dev mnt
$ mount -o remount,ro mnt
you would expect no warning, because the remount is not attempting to
change the free space tree setting, but we do see the warning.
To fix this, add explicit bool type casts to the condition.
I tested a variety of transitions:
sudo mount -o space_cache=v2 /dev/vg0/lv0 mnt/lol
(fst enabled)
mount -o remount,ro mnt/lol
(no warning, no fst change)
sudo mount -o remount,rw,space_cache=v1,clear_cache
(no warning, ro->rw)
sudo mount -o remount,rw,space_cache=v2 mnt
(warning, rw->rw with change)
sudo mount -o remount,ro mnt
(no warning, no fst change)
sudo mount -o remount,rw,space_cache=v2 mnt
(no warning, no fst change)
Reported-by: Chris Murphy <lists@colorremedies.com> CC: stable@vger.kernel.org # 5.11 Signed-off-by: Boris Burkov <boris@bur.io> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Following commit f218ea6c4792 ("btrfs: delayed-inode: Remove wrong
qgroup meta reservation calls") this function now reserves num_bytes,
rather than the fixed amount of nodesize. As such this requires the
same amount to be freed in case of failure. Fix this by adjusting
the amount we are freeing.
Fixes: f218ea6c4792 ("btrfs: delayed-inode: Remove wrong qgroup meta reservation calls") CC: stable@vger.kernel.org # 4.19+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The problem is we're copying "inherit" from user space but we don't
necessarily know that we're copying enough data for a 64 byte
struct. Then the next problem is that 'inherit' has a variable size
array at the end, and we have to verify that array is the size we
expected.
Fixes: 6f72c7e20dba ("Btrfs: add qgroup inheritance") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During allocation the allocator will try to allocate an extent using
cluster policy. Once the current cluster is exhausted it will remove the
entry under btrfs_free_cluster::lock and subsequently acquire
btrfs_free_space_ctl::tree_lock to dispose of the already-deleted entry
and adjust btrfs_free_space_ctl::total_bitmap. This poses a problem
because there exists a race condition between removing the entry under
one lock and doing the necessary accounting holding a different lock
since extent freeing only uses the 2nd lock. This can result in the
following situation:
T1: T2:
btrfs_alloc_from_cluster insert_into_bitmap <holds tree_lock>
if (entry->bytes == 0) if (block_group && !list_empty(&block_group->cluster_list)) {
rb_erase(entry)
spin_unlock(&cluster->lock);
(total_bitmaps is still 4) spin_lock(&cluster->lock);
<doesn't find entry in cluster->root>
spin_lock(&ctl->tree_lock); <goes to new_bitmap label, adds
<blocked since T2 holds tree_lock> <a new entry and calls add_new_bitmap>
recalculate_thresholds <crashes,
due to total_bitmaps
becoming 5 and triggering
an ASSERT>
To fix this ensure that once depleted, the cluster entry is deleted when
both cluster lock and tree locks are held in the allocator (T1), this
ensures that even if there is a race with a concurrent
insert_into_bitmap call it will correctly find the entry in the cluster
and add the new space to it.
CC: <stable@vger.kernel.org> # 4.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tree checker checks the extent ref hash at read and write time to
make sure we do not corrupt the file system. Generally extent
references go inline, but if we have enough of them we need to make an
item, which looks like
However if key.offset collide with an unrelated extent reference we'll
simply key.offset++ until we get something that doesn't collide.
Obviously this doesn't match at tree checker time, and thus we error
while writing out the transaction. This is relatively easy to
reproduce, simply do something like the following
xfs_io -f -c "pwrite 0 1M" file
offset=2
for i in {0..10000}
do
xfs_io -c "reflink file 0 ${offset}M 1M" file
offset=$(( offset + 2 ))
done
And the sync will error out because we'll abort the transaction. The
magic values above are used because they generate hash collisions with
the first file in the main subvol.
The fix for this is to remove the hash value check from tree checker, as
we have no idea which offset ours should belong to.
Reported-by: Tuomas Lähdekorpi <tuomas.lahdekorpi@gmail.com> Fixes: 0785a9aacf9d ("btrfs: tree-checker: Add EXTENT_DATA_REF check") CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ add comment] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using the NO_HOLES feature, if we clone a file range that spans only
a hole into a range that is at or beyond the current i_size of the
destination file, we end up not setting the full sync runtime flag on the
inode. As a result, if we then fsync the destination file and have a power
failure, after log replay we can end up exposing stale data instead of
having a hole for that range.
The conditions for this to happen are the following:
1) We have a file with a size of, for example, 1280K;
2) There is a written (non-prealloc) extent for the file range from 1024K
to 1280K with a length of 256K;
3) This particular file extent layout is durably persisted, so that the
existing superblock persisted on disk points to a subvolume root where
the file has that exact file extent layout and state;
4) The file is truncated to a smaller size, to an offset lower than the
start offset of its last extent, for example to 800K. The truncate sets
the full sync runtime flag on the inode;
6) Fsync the file to log it and clear the full sync runtime flag;
7) Clone a region that covers only a hole (implicit hole due to NO_HOLES)
into the file with a destination offset that starts at or beyond the
256K file extent item we had - for example to offset 1024K;
8) Since the clone operation does not find extents in the source range,
we end up in the if branch at the bottom of btrfs_clone() where we
punch a hole for the file range starting at offset 1024K by calling
btrfs_replace_file_extents(). There we end up not setting the full
sync flag on the inode, because we don't know we are being called in
a clone context (and not fallocate's punch hole operation), and
neither do we create an extent map to represent a hole because the
requested range is beyond eof;
9) A further fsync to the file will be a fast fsync, since the clone
operation did not set the full sync flag, and therefore it relies on
modified extent maps to correctly log the file layout. But since
it does not find any extent map marking the range from 1024K (the
previous eof) to the new eof, it does not log a file extent item
for that range representing the hole;
10) After a power failure no hole for the range starting at 1024K is
punched and we end up exposing stale data from the old 256K extent.
Turning this into exact steps:
$ mkfs.btrfs -f -O no-holes /dev/sdi
$ mount /dev/sdi /mnt
# Create our test file with 3 extents of 256K and a 256K hole at offset
# 256K. The file has a size of 1280K.
$ xfs_io -f -s \
-c "pwrite -S 0xab -b 256K 0 256K" \
-c "pwrite -S 0xcd -b 256K 512K 256K" \
-c "pwrite -S 0xef -b 256K 768K 256K" \
-c "pwrite -S 0x73 -b 256K 1024K 256K" \
/mnt/sdi/foobar
# Make sure it's durably persisted. We want the last committed super
# block to point to this particular file extent layout.
sync
# Now truncate our file to a smaller size, falling within a position of
# the second extent. This sets the full sync runtime flag on the inode.
# Then fsync the file to log it and clear the full sync flag from the
# inode. The third extent is no longer part of the file and therefore
# it is not logged.
$ xfs_io -c "truncate 800K" -c "fsync" /mnt/foobar
# Now do a clone operation that only clones the hole and sets back the
# file size to match the size it had before the truncate operation
# (1280K).
$ xfs_io \
-c "reflink /mnt/foobar 256K 1024K 256K" \
-c "fsync" \
/mnt/foobar
# File data before power failure:
$ od -A d -t x1 /mnt/foobar 0000000 ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab
* 0262144 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
* 0524288 cd cd cd cd cd cd cd cd cd cd cd cd cd cd cd cd
* 0786432 ef ef ef ef ef ef ef ef ef ef ef ef ef ef ef ef
* 0819200 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
* 1310720
<power fail>
# Mount the fs again to replay the log tree.
$ mount /dev/sdi /mnt
# File data after power failure:
$ od -A d -t x1 /mnt/foobar 0000000 ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab ab
* 0262144 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
* 0524288 cd cd cd cd cd cd cd cd cd cd cd cd cd cd cd cd
* 0786432 ef ef ef ef ef ef ef ef ef ef ef ef ef ef ef ef
* 0819200 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
* 1048576 73 73 73 73 73 73 73 73 73 73 73 73 73 73 73 73
* 1310720
The range from 1024K to 1280K should correspond to a hole but instead it
points to stale data, to the 256K extent that should not exist after the
truncate operation.
The issue does not exists when not using NO_HOLES, because for that case
we use file extent items to represent holes, these are found and copied
during the loop that iterates over extents at btrfs_clone(), and that
causes btrfs_replace_file_extents() to be called with a non-NULL
extent_info argument and therefore set the full sync runtime flag on the
inode.
So fix this by making the code that deals with a trailing hole during
cloning, at btrfs_clone(), to set the full sync flag on the inode, if the
range starts at or beyond the current i_size.
A test case for fstests will follow soon.
Backporting notes: for kernel 5.4 the change goes to ioctl.c into
btrfs_clone before the last call to btrfs_punch_hole_range.
CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a snapshot we check if the current number of swap files, in
the root, is non-zero, and if it is, we error out and warn that we can not
create the snapshot because there are active swap files.
However this is racy because when a task started activation of a swap
file, another task might have started already snapshot creation and might
have seen the counter for the number of swap files as zero. This means
that after the swap file is activated we may end up with a snapshot of the
same root successfully created, and therefore when the first write to the
swap file happens it has to fall back into COW mode, which should never
happen for active swap files.
Basically what can happen is:
1) Task A starts snapshot creation and enters ioctl.c:create_snapshot().
There it sees that root->nr_swapfiles has a value of 0 so it continues;
2) Task B enters btrfs_swap_activate(). It is not aware that another task
started snapshot creation but it did not finish yet. It increments
root->nr_swapfiles from 0 to 1;
3) Task B checks that the file meets all requirements to be an active
swap file - it has NOCOW set, there are no snapshots for the inode's
root at the moment, no file holes, no reflinked extents, etc;
4) Task B returns success and now the file is an active swap file;
5) Task A commits the transaction to create the snapshot and finishes.
The swap file's extents are now shared between the original root and
the snapshot;
6) A write into an extent of the swap file is attempted - there is a
snapshot of the file's root, so we fall back to COW mode and therefore
the physical location of the extent changes on disk.
So fix this by taking the snapshot lock during swap file activation before
locking the extent range, as that is the order in which we lock these
during buffered writes.
Fixes: ed46ff3d42378 ("Btrfs: support swap files") CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we active a swap file, at btrfs_swap_activate(), we acquire the
exclusive operation lock to prevent the physical location of the swap
file extents to be changed by operations such as balance and device
replace/resize/remove. We also call there can_nocow_extent() which,
among other things, checks if the block group of a swap file extent is
currently RO, and if it is we can not use the extent, since a write
into it would result in COWing the extent.
However we have no protection against a scrub operation running after we
activate the swap file, which can result in the swap file extents to be
COWed while the scrub is running and operating on the respective block
group, because scrub turns a block group into RO before it processes it
and then back again to RW mode after processing it. That means an attempt
to write into a swap file extent while scrub is processing the respective
block group, will result in COWing the extent, changing its physical
location on disk.
Fix this by making sure that block groups that have extents that are used
by active swap files can not be turned into RO mode, therefore making it
not possible for a scrub to turn them into RO mode. When a scrub finds a
block group that can not be turned to RO due to the existence of extents
used by swap files, it proceeds to the next block group and logs a warning
message that mentions the block group was skipped due to active swap
files - this is the same approach we currently use for balance.
Fixes: ed46ff3d42378 ("Btrfs: support swap files") CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Anand Jain <anand.jain@oracle.com> Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a qstripe is required an extra page is allocated and mapped. There
were 3 problems:
1) There is no corresponding call of kunmap() for the qstripe page.
2) There is no reason to map the qstripe page more than once if the
number of bits set in rbio->dbitmap is greater than one.
3) There is no reason to map the parity page and unmap it each time
through the loop.
The page memory can continue to be reused with a single mapping on each
iteration by raid6_call.gen_syndrome() without remapping. So map the
page for the duration of the loop.
Similarly, improve the algorithm by mapping the parity page just 1 time.
Fixes: 5a6ac9eacb49 ("Btrfs, raid56: support parity scrub on raid56") CC: stable@vger.kernel.org # 4.4.x: c17af96554a8: btrfs: raid56: simplify tracking of Q stripe presence CC: stable@vger.kernel.org # 4.4.x Signed-off-by: Ira Weiny <ira.weiny@intel.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's wrong calling btrfs_put_block_group in
__btrfs_return_cluster_to_free_space if the block group passed is
different than the block group the cluster represents. As this means the
cluster doesn't have a reference to the passed block group. This results
in double put and a use-after-free bug.
Fix this by simply bailing if the block group we passed in does not
match the block group on the cluster.
Fixes: fa9c0d795f7b ("Btrfs: rework allocation clustering") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is shown with Samsung Chromebook Pro (Caroline) with TPM 1.2
(SLB 9670):
[ 4.324298] TPM returned invalid status
[ 4.324806] WARNING: CPU: 2 PID: 1 at drivers/char/tpm/tpm_tis_core.c:275 tpm_tis_status+0x86/0x8f
Background
==========
TCG PC Client Platform TPM Profile (PTP) Specification, paragraph 6.1 FIFO
Interface Locality Usage per Register, Table 39 Register Behavior Based on
Locality Setting for FIFO - a read attempt to TPM_STS_x Registers returns
0xFF in case of lack of locality.
The fix
=======
Decorate tpm_get_timeouts() with request_locality() and release_locality().
Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()") Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Laurent Bigonville <bigon@debian.org> Cc: stable@vger.kernel.org Reported-by: Lukasz Majczak <lma@semihalf.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is shown with Samsung Chromebook Pro (Caroline) with TPM 1.2
(SLB 9670):
[ 4.324298] TPM returned invalid status
[ 4.324806] WARNING: CPU: 2 PID: 1 at drivers/char/tpm/tpm_tis_core.c:275 tpm_tis_status+0x86/0x8f
Background
==========
TCG PC Client Platform TPM Profile (PTP) Specification, paragraph 6.1 FIFO
Interface Locality Usage per Register, Table 39 Register Behavior Based on
Locality Setting for FIFO - a read attempt to TPM_STS_x Registers returns
0xFF in case of lack of locality.
The fix
=======
Decorate tpm_tis_gen_interrupt() with request_locality() and
release_locality().
Cc: Laurent Bigonville <bigon@debian.org> Cc: James Bottomley <James.Bottomley@HansenPartnership.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: stable@vger.kernel.org Fixes: a3fbfae82b4c ("tpm: take TPM chip power gating out of tpm_transmit()") Signed-off-by: Lukasz Majczak <lma@semihalf.com> Signed-off-by: Jarkko Sakkinen <jarkko@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent fix for the hw constraints for implicit feedback streams
via commit e4ea77f8e53f ("ALSA: usb-audio: Always apply the hw
constraints for implicit fb sync") added the check of the matching
endpoints and whether those EPs are already opened. This is needed
and correct, per se, even for the normal streams without the implicit
feedback, as the endpoint setup is exclusive.
However, it's reported that there seem applications that behave in
unexpected ways to update the hw_params without clearing the previous
setup via hw_free, and those hit a problem now: then hw_params is
called with still the previous EP setup kept, hence it's restricted
with the previous own setup. Although the obvious fix is to call
snd_pcm_hw_free() API in the application side, it's a kind of
unwelcome change.
This patch tries to ease the situation: in the endpoint check, we add
a couple of more conditions and now skip the endpoint that is being
used only by the stream in question itself. That is, in addition to
the presence check of ep (ep->cur_audiofmt is non-NULL), when the
following conditions are met, we skip such an ep:
- ep->opened == 1, and
- ep->cur_audiofmt == subs->cur_audiofmt.
subs->cur_audiofmt is non-NULL only if it's a re-setup of hw_params,
and ep->cur_audiofmt points to the currently set up parameters. So if
those match, it must be this stream itself.
Some USB audio firmware seem to report broken dB values for the volume
controls, and this screws up applications like PulseAudio who blindly
trusts the given data. For example, Edifier G2000 reports a PCM
volume from -128dB to -127dB, and this results in barely inaudible
sound.
This patch adds a sort of sanity check at parsing the dB values in
USB-audio driver and disables the dB reporting if the range looks
bogus. Here, we assume -96dB as the bottom line of the max dB.
Note that, if one can figure out that proper dB range later, it can be
patched in the mixer maps.
The commit 93db51d06b32 ("ALSA: usb-audio: Check valid altsetting at
parsing rates for UAC2/3") changed the behavior of the function
set_sample_rate_v2v3() slightly to treat the inconsistent sample rate
as an error. It was done by assumption that the sample rate
validation should have been done at the parser phase as implemented in
that patch. But the validation is later selectively enabled only for
certain devices as it causes a regression (the commit fe773b8711e3
"ALSA: usb-audio: workaround for iface reset issue"), and now the
inconsistency surfaced as a fatal error while it worked in the past as
is, as reported for FiiO M3K DAC.
For recovering from the regression, change set_sample_rate_v2v3()
again to ignore the sample rate difference as non-error.
The Corsair Virtuoso SE RGB Wireless is a USB headset with a mic and a
sidetone feature. Assign the Corsair Virtuoso name map to the SE product
ids as well, in order to label its mixer appropriately and allow
userspace to pick the correct volume controls.
The Acer SWIFT Swift SF314-54/55 laptops with ALC256 cannot detect
both the headset mic and the internal mic. Introduce new fixup
to enable the jack sense and the headset mic. However, the internal
mic actually connects to Intel SST audio. It still needs Intel SST
support to make internal mic capture work.
Signed-off-by: Chris Chiu <chris.chiu@canonical.com> Acked-by: Jian-Hong Pan <jhp@endlessos.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20210226010440.8474-1-chris.chiu@canonical.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is another MSI board (1462:cc34) that has dual Realtek codecs,
and we need to apply the existing quirk for fixing the conflicts of
Master control.
This adds a new SND_PCI_QUIRK(...) and applies it to the Intel NUC 10
devices. This fixes the issue of the devices not having audio input and
output on the headset jack because the kernel does not recognize when
something is plugged in.
The new quirk was inspired by the quirk for the Intel NUC 8 devices, but
it turned out that the NUC 10 uses another pin. This information was
acquired by black box testing likely pins.
This applies a SND_PCI_QUIRK(...) to the Clevo NH55RZQ barebone. This
fixes the issue of the device not recognizing a pluged in microphone.
The device has both, a microphone only jack, and a speaker + microphone
combo jack. The combo jack already works. The microphone-only jack does
not recognize when a device is pluged in without this patch.
This patch adds the missing MODULE_DEVICE_TABLE definitions on different
Mediatek phy drivers which generates correct modalias for automatic loading
when these drivers are compiled as an external module.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com> Link: https://lore.kernel.org/r/20210203110631.686003-1-enric.balletbo@collabora.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ICANON case is a bit messy, since it has to look for the line
ending, and has special code to then suppress line ending characters if
they match the __DISABLED_CHAR. So it actually looks up the line ending
even past the point where it knows it won't copy it to the result
buffer.
That said, apart from all those odd legacy N_TTY ICANON cases, the
actual "should we continue copying" logic isn't really all that
complicated or different from the non-canon case. In fact, the lack of
"wait for at least N characters" arguably makes the repeat case slightly
simpler. It really just boils down to "there's more of the line to be
copied".
So add the necessarily trivial logic, and now the N_TTY case will give
long result lines even when in canon mode.
With the conversion to do the tty ldisc read operations in small chunks,
the n_tty line discipline became noticeably slower for throughput
oriented loads, because rather than read things in up to 2kB chunks, it
would return at most 64 bytes per read() system call.
The cost is mainly all in the "do system calls over and over", not
really in the new "copy to an extra kernel buffer".
This can be fixed by teaching the n_tty line discipline about the
"cookie continuation" model, which the chunking code supports because
things like hdlc need to be able to handle packets up to 64kB in size.
Doing that doesn't just get us back to the old performace, but to much
better performance: my stupid "copy 10MB of data over a pty" test
program is now almost twice as fast as it used to be (going down from
0.1s to 0.054s).
This is entirely because it now creates maximal chunks (which happens to
be "one byte less than one page" due to how we do the circular tty
buffers).
NOTE! This case only handles the simpler non-icanon case, which is the
one where people may care about throughput. I'm going to do the icanon
case later too, because while performance isn't a major issue for that,
there may be programs that think they'll always get a full line and
don't like the 64-byte chunking for that reason.
Such programs are arguably buggy (signals etc can cause random partial
results from tty reads anyway), and good programs will handle such
partial reads, but expecting everybody to write "good programs" has
never been a winning policy for the kernel..
When I converted the tty_ldisc_ops 'read()' function to take a kernel
pointer, I was a bit too aggressive about the ldisc returning EOVERFLOW.
Yes, we want to have EOVERFLOW override any partially read data (because
the whole point is that the buffer was too small for the whole packet,
and we don't want to see partial packets), but it shouldn't override a
previous EFAULT.
And in fact, it really is just EOVERFLOW that is special and should
throw away any partially read data, not "any error". Admittedly
EOVERFLOW is currently the only one that can happen for a continuation
read - and if the first read iteration returns an error we won't have this issue.
So this is more of a technicality, but let's just make the intent very
explicit, and re-organize the error handling a bit so that this is all
clearer.
We're not factoring in the start of the file for where to write and
read the swapfile, which leads to very unfortunate side effects of
writing where we should not be...
Fixes: dd6bd0d9c7db ("swap: use bdev_read_page() / bdev_write_page()") Signed-off-by: Jens Axboe <axboe@kernel.dk> Cc: Anthony Iliopoulos <ailiop@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 9e2369c06c8a18 ("xen: add helpers to allocate unpopulated
memory") foreign mappings are using guest physical addresses allocated
via ZONE_DEVICE functionality.
This will result in problems for the case of no balloon memory hotplug
being configured, as the p2m list will only cover the initial memory
size of the domain. Any ZONE_DEVICE allocated address will be outside
the p2m range and thus a mapping can't be established with that memory
address.
Fix that by extending the p2m size for that case. At the same time add
a check for a to be created mapping to be within the p2m limits in
order to detect errors early.
While changing a comment, remove some 32-bit leftovers.
Commit 3194a1746e8a ("xen-netback: don't "handle" error by BUG()")
dropped respective a BUG_ON() without noticing that with this the
variable's value wouldn't be consumed anymore. With gnttab_set_map_op()
setting all status fields to a non-zero value, in case of an error no
slot should have a status of GNTST_okay (zero).
Bailing immediately from set_foreign_p2m_mapping() upon a p2m updating
error leaves the full batch in an ambiguous state as far as the caller
is concerned. Instead flags respective slots as bad, unmapping what
was mapped there right away.
HYPERVISOR_grant_table_op()'s return value and the individual unmap
slots' status fields get used only for a one-time - there's not much we
can do in case of a failure.
Note that there's no GNTST_enomem or alike, so GNTST_general_error gets
used.
The map ops' handle fields get overwritten just to be on the safe side.
Open-iSCSI sends passthrough PDUs over netlink, but the kernel should be
verifying that the provided PDU header and data lengths fall within the
netlink message to prevent accessing beyond that in memory.
Cc: stable@vger.kernel.org Reported-by: Adam Nichols <adam@grimm-co.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the iSCSI parameters are exported back through sysfs, it should be
enforcing that they never are more than PAGE_SIZE (which should be more
than enough) before accepting updates through netlink.
Change all iSCSI sysfs attributes to use sysfs_emit().
Cc: stable@vger.kernel.org Reported-by: Adam Nichols <adam@grimm-co.com> Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Chris Leech <cleech@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Protect the iSCSI transport handle, available in sysfs, by requiring
CAP_SYS_ADMIN to read it. Also protect the netlink socket by restricting
reception of messages to ones sent with CAP_SYS_ADMIN. This disables
normal users from being able to end arbitrary iSCSI sessions.
Cc: stable@vger.kernel.org Reported-by: Adam Nichols <adam@grimm-co.com> Reviewed-by: Chris Leech <cleech@redhat.com> Reviewed-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Lee Duncan <lduncan@suse.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Acer One S1002 tablet is using an analog mic on IN1 and has
its jack-detect connected to JD2_IN4N, instead of using the default
IN3 for its internal mic and JD1_IN4P for jack-detect.
Note it is also using AIF2 instead of AIF1 which is somewhat unusual,
this is correctly advertised in the ACPI CHAN package, so the speakers
do work without the quirk.
Add a quirk for the mic and jack-detect settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Link: https://lore.kernel.org/r/20210216213555.36555-5-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log