360 degree hinges devices with dual KIOX010A + KIOX020A accelerometers
always have both a KIOX010A and a KIOX020A ACPI device (one for each
accel).
Theoretical some vendor may re-use some DSDT for a non-convertible
stripping out just the KIOX020A ACPI device from the DSDT. Check that
both ACPI devices are present to make the check more robust.
AUDIT_TRIM is expected to be idempotent, but multiple executions resulted
in a refcount underflow and use-after-free.
git bisect fingered commit fb041bb7c0a9 ("locking/refcount: Consolidate
implementations of refcount_t") but this patch with its more thorough
checking that wasn't in the x86 assembly code merely exposed a previously
existing tree refcount imbalance in the case of tree trimming code that
was refactored with prune_one() to remove a tree introduced in
commit 8432c7006297 ("audit: Simplify locking around untag_chunk()")
Move the put_tree() to cover only the prune_one() case.
Passes audit-testsuite and 3 passes of "auditctl -t" with at least one
directory watch.
Cc: Jan Kara <jack@suse.cz> Cc: Will Deacon <will@kernel.org> Cc: Alexander Viro <viro@zeniv.linux.org.uk> Cc: Seiji Nishikawa <snishika@redhat.com> Cc: stable@vger.kernel.org Fixes: 8432c7006297 ("audit: Simplify locking around untag_chunk()") Signed-off-by: Richard Guy Briggs <rgb@redhat.com> Reviewed-by: Jan Kara <jack@suse.cz>
[PM: reformatted/cleaned-up the commit description] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A common implementation of isatty(3) involves calling a ioctl passing
a dummy struct argument and checking whether the syscall failed --
bionic and glibc use TCGETS (passing a struct termios), and musl uses
TIOCGWINSZ (passing a struct winsize). If the FD is a socket, we will
copy sizeof(struct ifreq) bytes of data from the argument and return
-EFAULT if that fails. The result is that the isatty implementations
may return a non-POSIX-compliant value in errno in the case where part
of the dummy struct argument is inaccessible, as both struct termios
and struct winsize are smaller than struct ifreq (at least on arm64).
Although there is usually enough stack space following the argument
on the stack that this did not present a practical problem up to now,
with MTE stack instrumentation it's more likely for the copy to fail,
as the memory following the struct may have a different tag.
Fix the problem by adding an early check for whether the ioctl is a
valid socket ioctl, and return -ENOTTY if it isn't.
Fixes: 44c02a2c3dc5 ("dev_ioctl(): move copyin/copyout to callers") Link: https://linux-review.googlesource.com/id/I869da6cf6daabc3e4b7b82ac979683ba05e27d4d Signed-off-by: Peter Collingbourne <pcc@google.com> Cc: <stable@vger.kernel.org> # 4.19 Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after ubifs_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Fixes: ca7f85be8d6c ("ubifs: Add support for encrypted symlinks") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20210702065350.209646-5-ebiggers@kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after f2fs_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
The stat() family of syscalls report the wrong size for encrypted
symlinks, which has caused breakage in several userspace programs.
Fix this by calling fscrypt_symlink_getattr() after ext4_getattr() for
encrypted symlinks. This function computes the correct size by reading
and decrypting the symlink target (if it's not already cached).
For more details, see the commit which added fscrypt_symlink_getattr().
Add a helper function fscrypt_symlink_getattr() which will be called
from the various filesystems' ->getattr() methods to read and decrypt
the target of encrypted symlinks in order to report the correct st_size.
Detailed explanation:
As required by POSIX and as documented in various man pages, st_size for
a symlink is supposed to be the length of the symlink target.
Unfortunately, st_size has always been wrong for encrypted symlinks
because st_size is populated from i_size from disk, which intentionally
contains the length of the encrypted symlink target. That's slightly
greater than the length of the decrypted symlink target (which is the
symlink target that userspace usually sees), and usually won't match the
length of the no-key encoded symlink target either.
This hadn't been fixed yet because reporting the correct st_size would
require reading the symlink target from disk and decrypting or encoding
it, which historically has been considered too heavyweight to do in
->getattr(). Also historically, the wrong st_size had only broken a
test (LTP lstat03) and there were no known complaints from real users.
(This is probably because the st_size of symlinks isn't used too often,
and when it is, typically it's for a hint for what buffer size to pass
to readlink() -- which a slightly-too-large size still works for.)
However, a couple things have changed now. First, there have recently
been complaints about the current behavior from real users:
- Breakage in rpmbuild:
https://github.com/rpm-software-management/rpm/issues/1682
https://github.com/google/fscrypt/issues/305
- Breakage in toybox cpio:
https://www.mail-archive.com/toybox@lists.landley.net/msg07193.html
- Breakage in libgit2: https://issuetracker.google.com/issues/189629152
(on Android public issue tracker, requires login)
Second, we now cache decrypted symlink targets in ->i_link. Therefore,
taking the performance hit of reading and decrypting the symlink target
in ->getattr() wouldn't be as big a deal as it used to be, since usually
it will just save having to do the same thing later.
Also note that eCryptfs ended up having to read and decrypt symlink
targets in ->getattr() as well, to fix this same issue; see
commit 3a60a1686f0d ("eCryptfs: Decrypt symlink target for stat size").
So, let's just bite the bullet, and read and decrypt the symlink target
in ->getattr() in order to report the correct st_size. Add a function
fscrypt_symlink_getattr() which the filesystems will call to do this.
(Alternatively, we could store the decrypted size of symlinks on-disk.
But there isn't a great place to do so, and encryption is meant to hide
the original size to some extent; that property would be lost.)
The patch breaks userspace implementations (e.g. fdutils) and introduces
regressions in behaviour. Previously, it was possible to O_NDELAY open a
floppy device with no media inserted or with write protected media without
an error. Some userspace tools use this particular behavior for probing.
It's not the first time when we revert this patch. Previous revert is in
commit f2791e7eadf4 (Revert "floppy: refactor open() flags handling").
[CAUSE]
Commit a27a94c2b0c7 ("btrfs: Make btrfs_find_device_by_devspec return
btrfs_device directly") moves the "missing" device path check into
btrfs_rm_device().
But btrfs_rm_device() itself can have case where it only receives
@devid, with NULL as @device_path.
In that case, calling strcmp() on NULL will trigger the NULL pointer
dereference.
Before that commit, we handle the "missing" case inside
btrfs_find_device_by_devspec(), which will not check @device_path at all
if @devid is provided, thus no way to trigger the bug.
[FIX]
Before calling strcmp(), also make sure @device_path is not NULL.
Reserve GPIO pins 85-88 as these aren't meant to be accessible from the
application CPUs (causes reboot). Yet another fix similar to 9134586715e3, 5f8d3ab136d0, which is needed to allow angler to boot after 3edfb7bd76bd ("gpiolib: Show correct direction from the beginning").
Fixes: feeaf56ac78d ("arm64: dts: msm8994 SoC and Huawei Angler (Nexus 6P) support") Signed-off-by: Petr Vorel <petr.vorel@gmail.com> Reviewed-by: Konrad Dybcio <konrad.dybcio@somainline.org> Link: https://lore.kernel.org/r/20210415193913.1836153-1-petr.vorel@gmail.com Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a port leaves a VLAN-aware bridge, the current code does not clear
other ports' matrix field bit. If the bridge is later set to VLAN-unaware
mode, traffic in the bridge may leak to that port.
Remove the VLAN filtering check in mt7530_port_bridge_leave.
Fixes: 474a2ddaa192 ("net: dsa: mt7530: fix VLAN traffic leaks") Fixes: 83163f7dca56 ("net: dsa: mediatek: add VLAN support for MT7530") Signed-off-by: DENG Qingfang <dqfext@gmail.com> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some USB BT adapters don't satisfy the MTU requirement mentioned in
commit e848dbd364ac ("Bluetooth: btusb: Add support USB ALT 3 for WBS")
and have ALT 3 setting that produces no/garbled audio. Some adapters
with larger MTU were also reported to have problems with ALT 3.
Add a flag and check it and MTU before selecting ALT 3, falling back to
ALT 1. Enable the flag for Realtek, restoring the previous behavior for
non-Realtek devices.
Tested with USB adapters (mtu<72, no/garbled sound with ALT3, ALT1
works) BCM20702A1 0b05:17cb, CSR8510A10 0a12:0001, and (mtu>=72, ALT3
works) RTL8761BU 0bda:8771, Intel AX200 8087:0029 (after disabling
ALT6). Also got reports for (mtu>=72, ALT 3 reported to produce bad
audio) Intel 8087:0a2b.
Signed-off-by: Pauli Virtanen <pav@iki.fi> Fixes: e848dbd364ac ("Bluetooth: btusb: Add support USB ALT 3 for WBS") Tested-by: Michał Kępień <kernel@kempniu.pl> Tested-by: Jonathan Lampérth <jon@h4n.dev> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__tipc_sendmsg() is called to send SYN packet by either tipc_sendmsg()
or tipc_connect(). The difference is in tipc_connect(), it will call
tipc_wait_for_connect() after __tipc_sendmsg() to wait until connecting
is done. So there's no need to wait in __tipc_sendmsg() for this case.
This patch is to fix it by calling tipc_wait_for_connect() only when dlen
is not 0 in __tipc_sendmsg(), which means it's called by tipc_connect().
Note this also fixes the failure in tipcutils/test/ptts/:
# ./tipcTS &
# ./tipcTC 9
(hang)
Fixes: 36239dab6da7 ("tipc: fix implicit-connect for SYN+") Reported-by: Shuang Li <shuali@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Jon Maloy <jmaloy@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It turns out that the SIGIO/FASYNC situation is almost exactly the same
as the EPOLLET case was: user space really wants to be notified after
every operation.
Now, in a perfect world it should be sufficient to only notify user
space on "state transitions" when the IO state changes (ie when a pipe
goes from unreadable to readable, or from unwritable to writable). User
space should then do as much as possible - fully emptying the buffer or
what not - and we'll notify it again the next time the state changes.
But as with EPOLLET, we have at least one case (stress-ng) where the
kernel sent SIGIO due to the pipe being marked for asynchronous
notification, but the user space signal handler then didn't actually
necessarily read it all before returning (it read more than what was
written, but since there could be multiple writes, it could leave data
pending).
The user space code then expected to get another SIGIO for subsequent
writes - even though the pipe had been readable the whole time - and
would only then read more.
This is arguably a user space bug - and Colin King already fixed the
stress-ng code in question - but the kernel regression rules are clear:
it doesn't matter if kernel people think that user space did something
silly and wrong. What matters is that it used to work.
So if user space depends on specific historical kernel behavior, it's a
regression when that behavior changes. It's on us: we were silly to
have that non-optimal historical behavior, and our old kernel behavior
was what user space was tested against.
Because of how the FASYNC notification was tied to wakeup behavior, this
was first broken by commits f467a6a66419 and 1b6b26ae7053 ("pipe: fix
and clarify pipe read/write wakeup logic"), but at the time it seems
nobody noticed. Probably because the stress-ng problem case ends up
being timing-dependent too.
It was then unwittingly fixed by commit 3a34b13a88ca ("pipe: make pipe
writes always wake up readers") only to be broken again when by commit 3b844826b6c6 ("pipe: avoid unnecessary EPOLLET wakeups under normal
loads").
And at that point the kernel test robot noticed the performance
refression in the stress-ng.sigio.ops_per_sec case. So the "Fixes" tag
below is somewhat ad hoc, but it matches when the issue was noticed.
Fix it for good (knock wood) by simply making the kill_fasync() case
separate from the wakeup case. FASYNC is quite rare, and we clearly
shouldn't even try to use the "avoid unnecessary wakeups" logic for it.
Link: https://lore.kernel.org/lkml/20210824151337.GC27667@xsang-OptiPlex-9020/ Fixes: 3b844826b6c6 ("pipe: avoid unnecessary EPOLLET wakeups under normal loads") Reported-by: kernel test robot <oliver.sang@intel.com> Tested-by: Oliver Sang <oliver.sang@intel.com> Cc: Eric Biederman <ebiederm@xmission.com> Cc: Colin Ian King <colin.king@canonical.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I had forgotten just how sensitive hackbench is to extra pipe wakeups,
and commit 3a34b13a88ca ("pipe: make pipe writes always wake up
readers") ended up causing a quite noticeable regression on larger
machines.
Now, hackbench isn't necessarily a hugely meaningful benchmark, and it's
not clear that this matters in real life all that much, but as Mel
points out, it's used often enough when comparing kernels and so the
performance regression shows up like a sore thumb.
It's easy enough to fix at least for the common cases where pipes are
used purely for data transfer, and you never have any exciting poll
usage at all. So set a special 'poll_usage' flag when there is polling
activity, and make the ugly "EPOLLET has crazy legacy expectations"
semantics explicit to only that case.
I would love to limit it to just the broken EPOLLET case, but the pipe
code can't see the difference between epoll and regular select/poll, so
any non-read/write waiting will trigger the extra wakeup behavior. That
is sufficient for at least the hackbench case.
Apart from making the odd extra wakeup cases more explicitly about
EPOLLET, this also makes the extra wakeup be at the _end_ of the pipe
write, not at the first write chunk. That is actually much saner
semantics (as much as you can call any of the legacy edge-triggered
expectations for EPOLLET "sane") since it means that you know the wakeup
will happen once the write is done, rather than possibly in the middle
of one.
[ For stable people: I'm putting a "Fixes" tag on this, but I leave it
up to you to decide whether you actually want to backport it or not.
It likely has no impact outside of synthetic benchmarks - Linus ]
Link: https://lore.kernel.org/lkml/20210802024945.GA8372@xsang-OptiPlex-9020/ Fixes: 3a34b13a88ca ("pipe: make pipe writes always wake up readers") Reported-by: kernel test robot <oliver.sang@intel.com> Tested-by: Sandeep Patil <sspatil@android.com> Tested-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In __init_el2_timers we initialize CNTHCTL_EL2.{EL1PCEN,EL1PCTEN} with a
RMW sequence, leaving all other bits UNKNOWN.
In general, we should initialize all bits in a register rather than
using an RMW sequence, since most bits are UNKNOWN out of reset, and as
new bits are added to the reigster their reset value might not result in
expected behaviour.
In the case of CNTHCTL_EL2, FEAT_ECV added a number of new control bits
in previously RES0 bits, which reset to UNKNOWN values, and may cause
issues for EL1 and EL0:
* CNTHCTL_EL2.ECV enables the CNTPOFF_EL2 offset (which itself resets to
an UNKNOWN value) at EL0 and EL1. Since the offset could reset to
distinct values across CPUs, when the control bit resets to 1 this
could break timekeeping generally.
* CNTHCTL_EL2.{EL1TVT,EL1TVCT} trap EL0 and EL1 accesses to the EL1
virtual timer/counter registers to EL2. When reset to 1, this could
cause unexpected traps to EL2.
Initializing these bits to zero avoids these problems, and all other
bits in CNTHCTL_EL2 other than EL1PCEN and EL1PCTEN can safely be reset
to zero.
This patch ensures we initialize CNTHCTL_EL2 accordingly, only setting
EL1PCEN and EL1PCTEN, and setting all other bits to zero.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Marc Zyngier <maz@kernel.org> Cc: Oliver Upton <oupton@google.com> Cc: Will Deacon <will@kernel.org> Reviewed-by: Oliver Upton <oupton@google.com> Acked-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20210818161535.52786-1-mark.rutland@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Function "dma_map_sg" is entitled to merge adjacent entries
and return a value smaller than what was passed as "nents".
Subsequently "ib_map_mr_sg" needs to work with this value ("sg_dma_len")
rather than the original "nents" parameter ("sg_len").
This old RDS bug was exposed and reliably causes kernel panics
(using RDMA operations "rds-stress -D") on x86_64 starting with:
commit c588072bba6b ("iommu/vt-d: Convert intel iommu driver to the iommu ops")
When booted with multiple displays attached, the EFI GOP driver on (at
least) Ampere, can leave DP links powered up that aren't being used to
display anything. This confuses our tracking of SOR routing, with the
likely result being a failed modeset and display engine hang.
Fix this by (ab?)using the DisableLT IED script to power-down the link,
restoring HW to a state the driver expects.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
Userspace should get back a copy of drm_wait_vblank that's been modified
even when drm_wait_vblank_ioctl returns a failure.
Rationale:
drm_wait_vblank_ioctl modifies the request and expects the user to read
it back. When the type is RELATIVE, it modifies it to ABSOLUTE and updates
the sequence to become current_vblank_count + sequence (which was
RELATIVE), but now it became ABSOLUTE.
drmWaitVBlank (in libdrm) expects this to be the case as it modifies
the request to be Absolute so it expects the sequence to would have been
updated.
The change is in compat_drm_wait_vblank, which is called by
drm_compat_ioctl. This change of copying the data back regardless of the
return number makes it en par with drm_ioctl, which always copies the
data before returning.
[How]
Return from the function after everything has been copied to user.
Fixes IGT:kms_flip::modeset-vs-vblank-race-interruptible
Tested on ChromeOS Trogdor(msm)
Inside blk_mq_queue_tag_busy_iter() we already grabbed request's
refcount before calling ->fn(), so needn't to grab it one more time
in blk_mq_check_expired().
Meantime remove extra request expire check in blk_mq_check_expired().
Cc: Keith Busch <kbusch@kernel.org> Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Reviewed-by: John Garry <john.garry@huawei.com> Link: https://lore.kernel.org/r/20210811155202.629575-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Asus TP200s / E205SA 360 degree hinges 2-in-1 supports reporting
SW_TABLET_MODE info through the ASUS_WMI_DEVID_LID_FLIP WMI device-id.
Add a quirk to enable this.
Unfortunately we have been unable to find a reliable way to detect if
and how SW_TABLET_MODE reporting is supported, so we are relying on
DMI quirks for this.
Add a module-option to specify the SW_TABLET_MODE method so that this can
be easily tested without needing to rebuild the kernel.
As __vringh_iov() traverses a descriptor chain, it populates
each descriptor entry into either read or write vring iov
and increments that iov's ->used member. So, as we iterate
over a descriptor chain, at any point, (riov/wriov)->used
value gives the number of descriptor enteries available,
which are to be read or written by the device. As all read
iovs must precede the write iovs, wiov->used should be zero
when we are traversing a read descriptor. Current code checks
for wiov->i, to figure out whether any previous entry in the
current descriptor chain was a write descriptor. However,
iov->i is only incremented, when these vring iovs are consumed,
at a later point, and remain 0 in __vringh_iov(). So, correct
the check for read and write descriptor order, to use
wiov->used.
Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org> Link: https://lore.kernel.org/r/1624591502-4827-1-git-send-email-neeraju@codeaurora.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Do not call vDPA drivers' callbacks with vq indicies larger than what
the drivers indicate that they support. vDPA drivers do not bounds
check the indices.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com> Link: https://lore.kernel.org/r/20210701114652.21956-1-vincent.whitchurch@axis.com Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When a virtio pci device undergo surprise removal (aka async removal in
PCIe spec), mark the device as broken so that any upper layer drivers can
abort any outstanding operation.
When a virtio net pci device undergo surprise removal which is used by a
NetworkManager, a below call trace was observed.
Currently vq->broken field is read by virtqueue_is_broken() in busy
loop in one context by virtnet_send_command().
vq->broken is set to true in other process context by
virtio_break_device(). Reader and writer are accessing it without any
synchronization. This may lead to a compiler optimization which may
result to optimize reading vq->broken only once.
Hence, force reading vq->broken on each invocation of
virtqueue_is_broken() and also force writing it so that such
update is visible to the readers.
It is a theoretical fix that isn't yet encountered in the field.
Some products (So) may have two different types of products
with different mac-type that are otherwise equivalent, and
have the same PNVM data, so the PNVM file will contain two
(or perhaps later more) HW-type TLVs. Accept the file and
use the data section that contains any matching entry.
The probe was manually passing NULL instead of dev to devm_clk_hw_register.
This caused a Unable to handle kernel NULL pointer dereference error.
Fix this by passing 'dev'.
Signed-off-by: Adam Ford <aford173@gmail.com> Fixes: a20a40a8bbc2 ("clk: renesas: rcar-usb2-clock-sel: Fix error handling in .probe()") Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Stephen Boyd <sboyd@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
push_rt_task() attempts to move the currently running task away if the
next runnable task has migration disabled and therefore is pinned on the
current CPU.
The current task is retrieved via get_push_task() which only checks for
nr_cpus_allowed == 1, but does not check whether the task has migration
disabled and therefore cannot be moved either. The consequence is a
pointless invocation of the migration thread which correctly observes
that the task cannot be moved.
Return NULL if the task has migration disabled and cannot be moved to
another CPU.
Fixes: a7c81556ec4d3 ("sched: Fix migrate_disable() vs rt/dl balancing") Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Link: https://lkml.kernel.org/r/20210826133738.yiotqbtdaxzjsnfj@linutronix.de Signed-off-by: Sasha Levin <sashal@kernel.org>
The u32 variable pci_dword is being masked with 0x1fffffff and then left
shifted 23 places. The shift is a u32 operation,so a value of 0x200 or
more in pci_dword will overflow the u32 and only the bottow 32 bits
are assigned to addr. I don't believe this was the original intent.
Fix this by casting pci_dword to a resource_size_t to ensure no
overflow occurs.
Note that the mask and 12 bit left shift operation does not need this
because the mask SNR_IMC_MMIO_MEM0_MASK and shift is always a 32 bit
value.
Fixes: ee49532b38dd ("perf/x86/intel/uncore: Add IMC uncore support for Snow Ridge")
Addresses-Coverity: ("Unintentional integer overflow") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Reviewed-by: Kan Liang <kan.liang@linux.intel.com> Link: https://lore.kernel.org/r/20210706114553.28249-1-colin.king@canonical.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the endpoint completion callback is call right after the ep_enabled flag
is cleared and before usb_ep_dequeue() is call, we could do a double free
on the request and the associated buffer.
Fix this by clearing ep_enabled after all the endpoint requests have been
dequeued.
Fixes: b60189e0392f ("net: stmmac: Integrate EST with TAPRIO scheduler API") Cc: <stable@vger.kernel.org> # 5.10.x Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add a mutex lock to protect est structure parameters so that the
EST parameters can be updated by other threads.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
It turned out that the change from the reverted commit breaks the ACPI
based rpi's because it causes the 100Mhz max clock to be overridden to the
return from sdhci_iproc_get_max_clock(), which is 0 because there isn't a
OF/DT based clock device.
Reported-by: Jeremy Linton <jeremy.linton@arm.com> Fixes: 419dd626e357 ("mmc: sdhci-iproc: Set SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN on BCM2711") Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The commit 71f642833284 ("ACPI: utils: Fix reference counting in
for_each_acpi_dev_match()") moved adev assignment outside of error
path and hence made acpi_dev_put(sensor->adev) a no-op. We still
need to drop reference count on error path, and to achieve that,
replace sensor->adev by locally assigned adev.
Fixes: 71f642833284 ("ACPI: utils: Fix reference counting in for_each_acpi_dev_match()")
Depends-on: fc68f42aa737 ("ACPI: fix NULL pointer dereference") Reported-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, when query PFC configuration by dcbtool, driver will return
PFC enable status based on TC. As all priorities are mapped to TC0 by
default, if TC0 is enabled, then all priorities mapped to TC0 will be
shown as enabled status when query PFC setting, even though some
priorities have never been set.
for example:
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:off 1:off 2:off 3:off 4:off 5:off 6:off 7:off
$ dcb pfc set dev eth0 prio-pfc 0:on 1:on 2:on 3:on
$ dcb pfc show dev eth0
pfc-cap 4 macsec-bypass off delay 0
prio-pfc 0:on 1:on 2:on 3:on 4:on 5:on 6:on 7:on
To fix this problem, just returns user's PFC config parameter saved in
driver.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
VLAN list should not be added duplicate VLAN node, otherwise it would
cause "add failed" when restore VLAN from VLAN list, so this patch adds
VLAN ID check before adding node into VLAN list.
In bond 4, when the link goes down and up repeatedly, the bond may get an
unknown speed, and then this port can not work.
The driver notify netif_carrier_on() before update the link state, when the
bond receive carrier on, will query the speed of the port, if the query
operation happens before updating the link state, will get an unknown
speed. So need to notify netif_carrier_on() after update the link state.
After the cmdq registers are cleared, the firmware may take time to
clear out possible left over commands in the cmdq. Driver must release
cmdq memory only after firmware has completed processing of left over
commands.
Fixes: 232d0d55fca6 ("net: hns3: uninitialize command queue while unloading PF driver") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a PF is bonded to a virtual machine and the virtual machine exits
unexpectedly, some hardware resource cannot be cleared. In this case,
loading driver may cause exceptions. Therefore, the hardware resource
needs to be cleared when the driver is loaded.
Currently when device is moved between network namespaces using
RTM_NEWLINK message type and one of netns attributes (FLA_NET_NS_PID,
IFLA_NET_NS_FD, IFLA_TARGET_NETNSID) but w/o specifying IFLA_IFNAME, and
target namespace already has device with same name, userspace will get
EINVAL what is confusing and makes debugging harder.
Fix it so that userspace gets more appropriate EEXIST instead what makes
debugging much easier.
Before:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 66:90:b5:d5:78:69 brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 6e:c6:1f:15:20:8d brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: Invalid argument
After:
# ./ifname.sh
+ ip netns add ns0
+ ip netns exec ns0 ip link add l0 type dummy
+ ip netns exec ns0 ip link show l0
8: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 1e:4a:72:e3:e3:8f brd ff:ff:ff:ff:ff:ff
+ ip link add l0 type dummy
+ ip link show l0
10: l0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether f2:fc:fe:2b:7d:a6 brd ff:ff:ff:ff:ff:ff
+ ip link set l0 netns ns0
RTNETLINK answers: File exists
The problem is that do_setlink() passes its `char *ifname` argument,
that it gets from a caller, to __dev_change_net_namespace() as is (as
`const char *pat`), but semantics of ifname and pat can be different.
, i.e. do_setlink() gets ifname pointer that is always valid no matter
if user specified IFLA_IFNAME or not and then do_setlink() passes this
ifname pointer as is to __dev_change_net_namespace() as pat argument.
But the pat (pattern) in __dev_change_net_namespace() is used as:
net/core/dev.c
11198 err = -EEXIST;
11199 if (__dev_get_by_name(net, dev->name)) {
11200 /* We get here if we can't use the current device name */
11201 if (!pat)
11202 goto out;
11203 err = dev_get_valid_name(net, dev, pat);
11204 if (err < 0)
11205 goto out;
11206 }
As the result the `goto out` path on line 11202 is neven taken and
instead of returning EEXIST defined on line 11198,
__dev_change_net_namespace() returns an error from dev_get_valid_name()
and this, in turn, will be EINVAL for ifname[0] = '\0' set earlier.
Fixes: d8a5ec672768 ("[NET]: netlink support for moving devices between network namespaces.") Signed-off-by: Andrey Ignatov <rdna@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Traffic schedules can only be started up to eight seconds within the
future. Therefore, the driver periodically checks every two seconds whether the
admin base time provided by the user is inside that window. If so the schedule
is started. Otherwise the check is deferred.
However, according to the programming manual the look ahead window size should
be four - not eight - seconds. By using the proposed value of four seconds
starting a schedule at a specified admin base time actually works as expected.
Fixes: 24dfc6eb39b2 ("net: dsa: hellcreek: Add TAPRIO offloading support") Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently the gate control list which is programmed into the hardware is
incorrect resulting in wrong traffic schedules. The problem is the loop
variables are incremented before they are referenced. Therefore, move the
increment to the end of the loop.
Fixes: 24dfc6eb39b2 ("net: dsa: hellcreek: Add TAPRIO offloading support") Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When adapter init fails, the blocked freelist bitmap is already freed
up and should not be touched. So, move the bitmap zeroing closer to
where it was successfully allocated. Also handle adapter init failure
unwind path immediately and avoid setting up RDMA memory windows.
Fixes: 5b377d114f2b ("cxgb4: Add debugfs facility to inject FL starvation") Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A group of security researchers brought to our attention
the weakness of hash function used in rt6_exception_hash()
Lets use siphash instead of Jenkins Hash, to considerably
reduce security risks.
Following patch deals with IPv4.
Fixes: 35732d01fe31 ("ipv6: introduce a hash table to store dst cache") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Keyu Man <kman001@ucr.edu> Cc: Wei Wang <weiwan@google.com> Cc: Martin KaFai Lau <kafai@fb.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the attempt to reserve a slot fails, we currently leak the XPT_BUSY
flag on the socket. Among other things, this make it impossible to close
the socket.
Fixes: 82011c80b3ec ("SUNRPC: Move svc_xprt_received() call sites") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: J. Bruce Fields <bfields@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the change() function decreases the value of 'nstrict', we must take
into account that packets might be already enqueued on a class that flips
from 'strict' to 'quantum': otherwise that class will not be added to the
bandwidth-sharing list. Then, a call to ets_qdisc_reset() will attempt to
do list_del(&alist) with 'alist' filled with zero, hence the NULL pointer
dereference.
For classes flipping from 'strict' to 'quantum', initialize an empty list
and eventually add it to the bandwidth-sharing list, if there are packets
already enqueued. In this way, the kernel will:
a) prevent crashing as described above.
b) avoid retaining the backlog packets (for an arbitrarily long time) in
case no packet is enqueued after a change from 'strict' to 'quantum'.
Reported-by: Hangbin Liu <liuhangbin@gmail.com> Fixes: dcc68b4d8084 ("net: sch_ets: Add a new Qdisc") Signed-off-by: Davide Caratti <dcaratti@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to increment the ucounts reference counter befor security_prepare_creds()
because this function may fail and abort_creds() will try to decrement
this reference.
According to Armada XP datasheet bit at 0 position is corresponding for
TxInProg indication.
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network unit") Signed-off-by: Maxim Kiselev <bigunclemax@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
A successful 'xge_mdio_config()' call should be balanced by a corresponding
'xge_mdio_remove()' call in the error handling path of the probe, as
already done in the remove function.
Update the error handling path accordingly.
Fixes: ea8ab16ab225 ("drivers: net: xgene-v2: Add MDIO support") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Validate csum_start in gre_handle_offloads before we call _gre_xmit so
that we do not crash later when the csum_start value is used in the
lco_csum function call.
This patch deals with ipv4 code.
Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Reported-by: syzbot+ff8e1b9f2f36481e2efc@syzkaller.appspotmail.com Signed-off-by: Shreyansh Chouhan <chouhan.shreyansh630@gmail.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
On new platforms, the NVM is read-only. Attempting to update the NVM
is causing a lockup to occur. Do not attempt to write to the NVM
on platforms where it's not supported.
Emit an error message when the NVM checksum is invalid.
We should decode the latency and the max_latency before directly compare.
The latency should be presented as lat_enc = scale x value:
lat_enc_d = (lat_enc & 0x0x3ff) x (1U << (5*((max_ltr_enc & 0x1c00)
>> 10)))
Fixes: cf8fb73c23aa ("e1000e: add support for LTR on I217/I218") Suggested-by: Yee Li <seven.yi.lee@gmail.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Use num_tx_queues rather than the IGC_MAX_TX_QUEUES fixed number 4 when
iterating over tx_ring queue since instantiated queue count could be
less than 4 where on-line cpu count is less than 4.
Fixes: ec50a9d437f0 ("igc: Add support for taprio offloading") Signed-off-by: Toshiki Nishioka <toshiki.nishioka@intel.com> Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Tested-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Acked-by: Sasha Neftin <sasha.neftin@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After unplug thunderbolt dock with i225, pciehp interrupt is triggered,
remove call will read/write mmio address which is already disconnected,
then cause page fault and make system hang.
Fixes: 13b5b7fd6a4a ("igc: Add support for Tx/Rx rings") Fixes: b03c49cde61f ("igc: Save PTP time before a reset") Signed-off-by: Aaron Ma <aaron.ma@canonical.com> Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
- restore the behavior in enable_net_traffic() to avoid regressions - Jakub
Kicinski;
- hurried up and removed redundant assignment in pegasus_open() before yet
another checker complains;
Fixes: 8a160e2e9aeb ("net: usb: pegasus: Check the return value of get_geristers() and friends;") Reported-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Petko Manolov <petko.manolov@konsulko.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The devlink dev info command reports version information about the
device and firmware running on the board. This includes the "board.id"
field which is supposed to represent an identifier of the board design.
The ice driver uses the Product Board Assembly identifier for this.
In some cases, the PBA is not present in the NVM. If this happens,
devlink dev info will fail with an error. Instead, modify the
ice_info_pba function to just exit without filling in the context
buffer. This will cause the board.id field to be skipped. Log a dev_dbg
message in case someone wants to confirm why board.id is not showing up
for them.
Fixes: e961b679fb0b ("ice: add board identifier info to devlink .info_get") Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Tested-by: Tony Brelinski <tonyx.brelinski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20210819223451.245613-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
rxe_mcast_add_grp_elem() in rxe_mcast.c calls rxe_alloc() while holding
spinlocks which in turn calls kzalloc(size, GFP_KERNEL) which is
incorrect. This patch replaces rxe_alloc() by rxe_alloc_locked() which
uses GFP_ATOMIC. This bug was caused by the below mentioned commit and
failing to handle the need for the atomic allocate.
Fixes: 4276fd0dddc9 ("RDMA/rxe: Remove RXE_POOL_ATOMIC") Link: https://lore.kernel.org/r/20210813210625.4484-1-rpearsonhpe@gmail.com Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Bob Pearson <rpearsonhpe@gmail.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The fixed commit removes all rtnl_lock() and rtnl_unlock() calls in
function bnxt_re_dev_init(), but forgets to remove a rtnl_unlock() in the
error handling path of bnxt_re_register_netdev(), which may cause a
deadlock. This bug is suggested by a static analysis tool.
Fixes: c2b777a95923 ("RDMA/bnxt_re: Refactor device add/remove functionalities") Link: https://lore.kernel.org/r/20210816085531.12167-1-dinghao.liu@zju.edu.cn Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Acked-by: Selvin Xavier <selvin.xavier@broadcom.com> Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
kmalloc_array() is called to allocate memory for tx->descp. If it fails,
the function __sdma_txclean() is called:
__sdma_txclean(dd, tx);
However, in the function __sdma_txclean(), tx-descp is dereferenced if
tx->num_desc is not zero:
sdma_unmap_desc(dd, &tx->descp[0]);
To fix this possible null-pointer dereference, assign the return value of
kmalloc_array() to a local variable descp, and then assign it to tx->descp
if it is not NULL. Otherwise, go to enomem.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Link: https://lore.kernel.org/r/20210806133029.194964-1-islituo@gmail.com Reported-by: TOTE Robot <oslab@tsinghua.edu.cn> Signed-off-by: Tuo Li <islituo@gmail.com> Tested-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Acked-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix the below crash when deleting a slave from the unaffiliated list
twice. First time when the slave is bound to the master and the second
when the slave is unloaded.
Fix it by checking if slave is unaffiliated (doesn't have ib device)
before removing from the list.
blk_mq_run_hw_queues
^^^^^^ dispatch IO, q_usage_counter will reduce to zero
blk_mq_unfreeze_queue
^^^^^ mq_freeze_depth--
To fix this, we need to run queue before rescanning device when the device
state changes to SDEV_RUNNING.
Link: https://lore.kernel.org/r/20210824025921.3277629-1-lijinlin3@huawei.com Fixes: f0f82e2476f6 ("scsi: core: Fix capacity set to zero after offlinining device") Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Li Jinlin <lijinlin3@huawei.com> Signed-off-by: Qiu Laibin <qiulaibin@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During a USB cable disconnect, or soft disconnect scenario, a pending
SETUP transaction may not be completed, leading to the following
error:
dwc3 a600000.dwc3: timed out waiting for SETUP phase
If this occurs, then the entire pullup disable routine is skipped and
proper cleanup and halting of the controller does not complete.
Instead of returning an error (which is ignored from the UDC
perspective), allow the pullup disable routine to continue, which
will also handle disabling of EP0/1. This will end any active
transfers as well. Ensure to clear any delayed_status also, as the
timeout could happen within the STATUS stage.
Fixes: bb0147364850 ("usb: dwc3: gadget: don't clear RUN/STOP when it's invalid to do so") Cc: <stable@vger.kernel.org> Reviewed-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Acked-by: Felipe Balbi <balbi@kernel.org> Signed-off-by: Wesley Cheng <wcheng@codeaurora.org> Link: https://lore.kernel.org/r/20210825042855.7977-1-wcheng@codeaurora.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't depend on the TRB's HWO bit to determine if the TRB ring is
"full". A TRB is only available when the driver had processed it, not
when the controller consumed and relinquished the TRB's ownership to the
driver. Otherwise, the driver may overwrite unprocessed TRBs. This can
happen when many transfer events accumulate and the system is slow to
process them and/or when there are too many small requests.
If a request is in the started_list, that means there is one or more
unprocessed TRBs remained. Check this instead of the TRB's HWO bit
whether the TRB ring is full.
If the port is going to send Discover_Identity Message, vdm_sm_running
flag was intentionally set before entering Ready States in order to
avoid the conflict because the port and the port partner might start
AMS at almost the same time after entering Ready States.
However, the original design has a problem. When the port is doing
DR_SWAP from Device to Host, it raises the flag. Later in the
tcpm_send_discover_work, the flag blocks the procedure of sending the
Discover_Identity and it might never be cleared until disconnection.
Since there exists another flag send_discover representing that the port
is going to send Discover_Identity or not, it is enough to use that flag
to prevent the conflict. Also change the timing of the set/clear of
vdm_sm_running to indicate whether the VDM SM is actually running or
not.
The recent attempt to handle an unknown ROM state in the commit d143825baf15 ("usb: renesas-xhci: Fix handling of unknown ROM state")
resulted in a regression and reverted later by the commit 44cf53602f5a
("Revert "usb: renesas-xhci: Fix handling of unknown ROM state"").
The problem of the former fix was that it treated the failure of
firmware loading as a fatal error. Since the firmware files aren't
included in the standard linux-firmware tree, most users don't have
them, hence they got the non-working system after that. The revert
fixed the regression, but also it didn't make the firmware loading
triggered even on the devices that do need it. So we need still a fix
for them.
This is another attempt to handle the unknown ROM state. Like the
previous fix, this also tries to load the firmware when ROM shows
unknown state. In this patch, however, the failure of a firmware
loading (such as a missing firmware file) isn't handled as a fatal
error any longer when ROM has been already detected, but it falls back
to the ROM mode like before. The error is returned only when no ROM
is detected and the firmware loading failed.
Along with it, for simplifying the code flow, the detection and the
check of ROM is factored out from renesas_fw_check_running() and done
in the caller side, renesas_xhci_check_request_fw(). It avoids the
redundant ROM checks.
The patch was tested on Lenovo Thinkpad T14 gen (BIOS 1.34). Also it
was confirmed that no regression is seen on another Thinkpad T14
machine that has worked without the patch, too.
These devices do not appear to send a zero-length packet when the
transfer size is a multiple of the bulk-endpoint max-packet size. This
means that incoming data may not be processed by the driver until a
short packet is received or the receive buffer is full.
Revert back to using endpoint-sized receive buffers to avoid stalled
reads.
schedule_delayed_work does not push back the work if it was already
scheduled before, so amdgpu_device_delay_enable_gfx_off ran ~100 ms
after the first time GFXOFF was disabled and re-enabled, even if GFXOFF
was disabled and re-enabled again during those 100 ms.
This resulted in frame drops / stutter with the upcoming mutter 41
release on Navi 14, due to constantly enabling GFXOFF in the HW and
disabling it again (for getting the GPU clock counter).
To fix this, call cancel_delayed_work_sync when the disable count
transitions from 0 to 1, and only schedule the delayed work on the
reverse transition, not if the disable count was already 0. This makes
sure the delayed work doesn't run at unexpected times, and allows it to
be lock-free.
v2:
* Use cancel_delayed_work_sync & mutex_trylock instead of
mod_delayed_work.
v3:
* Make amdgpu_device_delay_enable_gfx_off lock-free (Christian König)
v4:
* Fix race condition between amdgpu_gfx_off_ctrl incrementing
adev->gfx.gfx_off_req_count and amdgpu_device_delay_enable_gfx_off
checking for it to be 0 (Evan Quan)
Cc: stable@vger.kernel.org Reviewed-by: Evan Quan <evan.quan@amd.com> Reviewed-by: Lijo Lazar <lijo.lazar@amd.com> # v3 Acked-by: Christian König <christian.koenig@amd.com> # v3 Signed-off-by: Michel Dänzer <mdaenzer@redhat.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drm_dp_dpcd_read/write already has debug error message.
Drop redundant error messages which gives false
status even if correct value is read in drm_dp_dpcd_read().
v2: -Added fixes tag (Ankit)
v3: -Fixed build error (CI)
Fixes: 9488a030ac91 ("drm/i915: Add support for enabling link status and recovery") Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com> Cc: Imre Deak <imre.deak@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Cc: José Roberto de Souza <jose.souza@intel.com> Cc: Manasi Navare <manasi.d.navare@intel.com> Cc: Sean Paul <seanpaul@chromium.org> Cc: Uma Shankar <uma.shankar@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: <stable@vger.kernel.org> # v5.12+ Reviewed-by: Jani Nikula <jani.nikula@intel.com> Signed-off-by: Swati Sharma <swati2.sharma@intel.com> Signed-off-by: Jani Nikula <jani.nikula@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20210812131107.5531-1-swati2.sharma@intel.com
(cherry picked from commit b6dfa416172939edaa46a5a647457b94c6d94119) Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A small race exists between intel_gt_retire_requests_timeout and
intel_timeline_exit which could result in the syncmap not getting
free'd. Rather than work to hard to seal this race, simply cleanup the
syncmap on fini.
After free xsk_pool, there is possibility that napi polling is still
running in the middle, thus causes a kernel crash due to kernel NULL
pointer dereference of rx_q->xsk_pool and tx_q->xsk_pool.
Fix this by changing the XDP pool setup sequence to:
1. disable napi before free xsk_pool
2. enable napi after init xsk_pool
The following kernel panic is observed without this patch:
[BUG]
It's no longer possible to create compressed inline extent after commit f2165627319f ("btrfs: compression: don't try to compress if we don't
have enough pages").
[CAUSE]
For compression code, there are several possible reasons we have a range
that needs to be compressed while it's no more than one page.
- Compressed inline write
The data is always smaller than one sector and the test lacks the
condition to properly recognize a non-inline extent.
- Compressed subpage write
For the incoming subpage compressed write support, we require page
alignment of the delalloc range.
And for 64K page size, we can compress just one page into smaller
sectors.
For those reasons, the requirement for the data to be more than one page
is not correct, and is already causing regression for compressed inline
data writeback. The idea of skipping one page to avoid wasting CPU time
could be revisited in the future.
[FIX]
Fix it by reverting the offending commit.
Reported-by: Zygo Blaxell <ce3g8jdj@umail.furryterror.org> Link: https://lore.kernel.org/linux-btrfs/afa2742.c084f5d6.17b6b08dffc@tnonline.net Fixes: f2165627319f ("btrfs: compression: don't try to compress if we don't have enough pages") CC: stable@vger.kernel.org # 4.4+ Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If offline_pages failed after lru_cache_disable(), it forgot to do
lru_cache_enable() in error path. So we would have lru cache disabled
permanently in this case.
Link: https://lkml.kernel.org/r/20210821094246.10149-3-linmiaohe@huawei.com Fixes: d479960e44f2 ("mm: disable LRU pagevec during the migration temporarily") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Oscar Salvador <osalvador@suse.de> Reviewed-by: Naoya Horiguchi <naoya.horiguchi@nec.com> Cc: Chris Goldsworthy <cgoldswo@codeaurora.org> Cc: Michal Hocko <mhocko@suse.com> Cc: Minchan Kim <minchan@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 66f24fa766e3 ("mm: drop redundant ARCH_ENABLE_SPLIT_PMD_PTLOCK")
broke PMD split page table lock for powerpc.
It selects the non-existent config ARCH_ENABLE_PMD_SPLIT_PTLOCK in
arch/powerpc/platforms/Kconfig.cputype, but clearly intended to
select ARCH_ENABLE_SPLIT_PMD_PTLOCK (notice the word swapping!), as
that commit did for all other architectures.
Fix it by selecting the correct symbol ARCH_ENABLE_SPLIT_PMD_PTLOCK.
Fixes: 66f24fa766e3 ("mm: drop redundant ARCH_ENABLE_SPLIT_PMD_PTLOCK") Cc: stable@vger.kernel.org # v5.13+ Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com> Reviewed-by: Daniel Axtens <dja@axtens.net>
[mpe: Reword change log to make it clear this is a bug fix] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20210819113954.17515-3-lukas.bulwahn@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value of FP registers in the core dump file comes from the
thread.fstate. However, kernel saves the FP registers to the thread.fstate
only before scheduling out the process. If no process switch happens
during the exception handling process, kernel will not have a chance to
save the latest value of FP registers to thread.fstate. It will cause the
value of FP registers in the core dump file may be incorrect. To solve this
problem, this patch force lets kernel save the FP register into the
thread.fstate if the target task_struct equals the current.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com> Reviewed-by: Jisheng Zhang <jszhang@kernel.org> Fixes: b8c8a9590e4f ("RISC-V: Add FP register ptrace support for gdb.") Cc: stable@vger.kernel.org Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the schema fixups are applied to 'select' the result is a single
entry is required for a match, but that will never match as there should
be 2 entries. Also, a 'select' schema should have the widest possible
match, so use 'contains' which matches the compatible string(s) in any
position and not just the first position.