Commit b0b524f079a2 ("brcmfmac: use ISO3166 country code and 0 rev
as fallback") changes country setup to directly use ISO3166 country
codes if no more specific code is configured. This was done under
the assumption that brcmfmac firmwares can handle such simple
direct mapping from country codes to firmware ccode values.
Unfortunately this is not true for all chipset/firmware combinations.
E.g. BCM4359/9 devices stop working as access point with this change,
so revert the offending commit to avoid the regression.
Many users are reporting that the Samsung 860 and 870 SSD are having
various issues when combined with AMD/ATI (vendor ID 0x1002) SATA
controllers and only completely disabling NCQ helps to avoid these
issues.
Always disabling NCQ for Samsung 860/870 SSDs regardless of the host
SATA adapter vendor will cause I/O performance degradation with well
behaved adapters. To limit the performance impact to ATI adapters,
introduce the ATA_HORKAGE_NO_NCQ_ON_ATI flag to force disable NCQ
only for these adapters.
Also, two libata.force parameters (noncqati and ncqati) are introduced
to disable and enable the NCQ for the system which equipped with ATI
SATA adapter and Samsung 860 and 870 SSDs. The user can determine NCQ
function to be enabled or disabled according to the demand.
After verifying the chipset from the user reports, the issue appears
on AMD/ATI SB7x0/SB8x0/SB9x0 SATA Controllers and does not appear on
recent AMD SATA adapters. The vendor ID of ATI should be 0x1002.
Therefore, ATA_HORKAGE_NO_NCQ_ON_AMD was modified to
ATA_HORKAGE_NO_NCQ_ON_ATI.
perf_init_event tries multiple init callbacks and does not reset the
event state between tries. When x86_pmu_event_init runs, it
unconditionally sets the destroy callback to hw_perf_event_destroy. On
the next init attempt after x86_pmu_event_init, in perf_try_init_event,
if the pmu's capabilities includes PERF_PMU_CAP_NO_EXCLUDE, the destroy
callback will be run. However, if the next init didn't set the destroy
callback, hw_perf_event_destroy will be run (since the callback wasn't
reset).
Looking at other pmu init functions, the common pattern is to only set
the destroy callback on a successful init. Resetting the callback on
failure tries to replicate that pattern.
This was discovered after commit f11dd0d80555 ("perf/x86/amd/ibs: Extend
PERF_PMU_CAP_NO_EXCLUDE to IBS Op") when the second (and only second)
run of the perf tool after a reboot results in 0 samples being
generated. The extra run of hw_perf_event_destroy results in
active_events having an extra decrement on each perf run. The second run
has active_events == 0 and every subsequent run has active_events < 0.
When active_events == 0, the NMI handler will early-out and not record
any samples.
Intel PMU MSRs is in msrs_to_save_all[], so add AMD PMU MSRs to have a
consistent behavior between Intel and AMD when using KVM_GET_MSRS,
KVM_SET_MSRS or KVM_GET_MSR_INDEX_LIST.
We have to add legacy and new MSRs to handle guests running without
X86_FEATURE_PERFCTR_CORE.
When exiting SMM, pdpts are loaded again from the guest memory.
This fixes a theoretical bug, when exit from SMM triggers entry to the
nested guest which re-uses some of the migration
code which uses this flag as a workaround for a legacy userspace.
grow_halt_poll_ns() ignores values between 0 and
halt_poll_ns_grow_start (10000 by default). However,
when we shrink halt_poll_ns we may fall way below
halt_poll_ns_grow_start and endup with halt_poll_ns
values that don't make a lot of sense: like 1 or 9,
or 19.
The SMC64 calling convention passes a function identifier in w0 and its
parameters in x1-x17. Given this, there are two deviations in the
SMC64 call performed by the steal_time test: the function identifier is
assigned to a 64 bit register and the parameter is only 32 bits wide.
Align the call with the SMCCC by using a 32 bit register to handle the
function identifier and increasing the parameter width to 64 bits.
Suggested-by: Andrew Jones <drjones@redhat.com> Signed-off-by: Oliver Upton <oupton@google.com> Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-Id: <20210921171121.2148982-3-oupton@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the asan-stack parameter is only passed along if
CFLAGS_KASAN_SHADOW is not empty, which requires KASAN_SHADOW_OFFSET to
be defined in Kconfig so that the value can be checked. In RISC-V's
case, KASAN_SHADOW_OFFSET is not defined in Kconfig, which means that
asan-stack does not get disabled with clang even when CONFIG_KASAN_STACK
is disabled, resulting in large stack warnings with allmodconfig:
drivers/video/fbdev/omap2/omapfb/displays/panel-lgphilips-lb035q02.c:117:12: error: stack frame size (14400) exceeds limit (2048) in function 'lb035q02_connect' [-Werror,-Wframe-larger-than]
static int lb035q02_connect(struct omap_dss_device *dssdev)
^
1 error generated.
Ensure that the value of CONFIG_KASAN_STACK is always passed along to
the compiler so that these warnings do not happen when
CONFIG_KASAN_STACK is disabled.
Link: https://github.com/ClangBuiltLinux/linux/issues/1453
References: 6baec880d7a5 ("kasan: turn off asan-stack for clang-8 and earlier") Link: https://lkml.kernel.org/r/20210922205525.570068-1-nathan@kernel.org Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Marco Elver <elver@google.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Alexander Potapenko <glider@google.com> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Dmitry Vyukov <dvyukov@google.com> Cc: Nick Desaulniers <ndesaulniers@google.com> Cc: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Idle page tracking can also be used for process address space, not only
file mappings.
Without this change, using with '-i' option for process address space
encounters below errors reported.
$ sudo ./page-types -p $(pidof bash) -i
mark page idle: Bad file descriptor
mark page idle: Bad file descriptor
mark page idle: Bad file descriptor
mark page idle: Bad file descriptor
...
Link: https://lkml.kernel.org/r/20210917032826.10669-1-changbin.du@gmail.com Signed-off-by: Changbin Du <changbin.du@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
rq_qos framework is only applied on request based driver, so:
1) rq_qos_done_bio() needn't to be called for bio based driver
2) rq_qos_done_bio() needn't to be called for bio which isn't tracked,
such as bios ended from error handling code.
Especially in bio_endio():
1) request queue is referred via bio->bi_bdev->bd_disk->queue, which
may be gone since request queue refcount may not be held in above two
cases
2) q->rq_qos may be freed in blk_cleanup_queue() when calling into
__rq_qos_done_bio()
Fix the potential kernel panic by not calling rq_qos_ops->done_bio if
the bio isn't tracked. This way is safe because both ioc_rqos_done_bio()
and blkcg_iolatency_done_bio() are nop if the bio isn't tracked.
Reported-by: Yu Kuai <yukuai3@huawei.com> Cc: tj@kernel.org Signed-off-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Christoph Hellwig <hch@lst.de> Acked-by: Tejun Heo <tj@kernel.org> Link: https://lore.kernel.org/r/20210924110704.1541818-1-ming.lei@redhat.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Sasha Levin <sashal@kernel.org>
If we have a lot of threads and rings, the tctx list can get quite big.
This is especially true if we keep creating new threads and rings.
Likewise for the provided buffers list. Be nice and insert a conditional
reschedule point while iterating the nodes for deletion.
Don't perform unaligned loads in __get_next() and __peek_nbyte_next() as
these are forms of undefined behavior:
"A pointer to an object or incomplete type may be converted to a pointer
to a different object or incomplete type. If the resulting pointer
is not correctly aligned for the pointed-to type, the behavior is
undefined."
fs/smbfs_client/smb2pdu.c:2425 create_sd_buf()
warn: struct type mismatch 'smb3_acl vs cifs_acl'
Pointed out by Dan Carpenter via smatch code analysis tool
Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Geert reported that the GIC driver locks up on a Renesas system
since 005c34ae4b44f085 ("irqchip/gic: Atomically update affinity")
fixed the driver to use writeb_relaxed() instead of writel_relaxed().
As it turns out, the interconnect used on this system mandates
32bit wide accesses for all MMIO transactions, even if the GIC
architecture specifically mandates for some registers to be byte
accessible. Gahhh...
Work around the issue by crudly detecting the offending system,
and falling back to an inefficient RMW+lock implementation.
Setting SCSI logging level with error=3, we saw some errors from enclosues:
[108017.360833] ses 0:0:9:0: tag#641 Done: NEEDS_RETRY Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK cmd_age=0s
[108017.360838] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427778] ses 0:0:9:0: Power-on or device reset occurred
[108017.427784] ses 0:0:9:0: tag#641 Done: SUCCESS Result: hostbyte=DID_OK driverbyte=DRIVER_OK cmd_age=0s
[108017.427788] ses 0:0:9:0: tag#641 CDB: Receive Diagnostic 1c 01 01 00 20 00
[108017.427791] ses 0:0:9:0: tag#641 Sense Key : Unit Attention [current]
[108017.427793] ses 0:0:9:0: tag#641 Add. Sense: Bus device reset function occurred
[108017.427801] ses 0:0:9:0: Failed to get diagnostic page 0x1
[108017.427804] ses 0:0:9:0: Failed to bind enclosure -19
[108017.427895] ses 0:0:10:0: Attached Enclosure device
[108017.427942] ses 0:0:10:0: Attached scsi generic sg18 type 13
Retry if the Send/Receive Diagnostic commands complete with a transient
error status (NOT_READY or UNIT_ATTENTION with ASC 0x29).
Link: https://lore.kernel.org/r/1631849061-10210-2-git-send-email-wenxiong@linux.ibm.com Reviewed-by: Brian King <brking@linux.ibm.com> Reviewed-by: James Bottomley <jejb@linux.ibm.com> Signed-off-by: Wen Xiong <wenxiong@linux.ibm.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Some devices can have some thermal sensors disabled from the
factory. The current two irq handler functions check all the sensor by
default and the check if the sensor was actually registered is
wrong. The tzd is actually never set if the registration fails hence
the IS_ERR check is wrong.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> Reviewed-by: Matthias Kaehlcke <mka@chromium.org> Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20210907212543.20220-1-ansuelsmth@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
To avoid race between time out and tear down, in tear down process,
first we quiesce the queue, and then delete the timer and cancel
the time out work for the queue.
This patch merges the admin and io sync ops into the queue teardown logic
as shown in the RDMA patch 3017013dcc "nvme-rdma: avoid race between time
out and tear down". There is no teardown_lock in nvme-fc.
Signed-off-by: James Smart <jsmart2021@gmail.com> Tested-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: Daniel Wagner <dwagner@suse.de> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In case the number of hardware queues changes, we need to update the
tagset and the mapping of ctx to hctx first.
If we try to create and connect the I/O queues first, this operation
will fail (target will reject the connect call due to the wrong number
of queues) and hence we bail out of the recreate function. Then we
will to try the very same operation again, thus we don't make any
progress.
Signed-off-by: Daniel Wagner <dwagner@suse.de> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com> Reviewed-by: Hannes Reinecke <hare@suse.de> Reviewed-by: James Smart <jsmart2021@gmail.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
While the hypervisor hasn't been enforcing this, we would still better
avoid issuing requests with GFNs not aligned to the requested order.
Instead of altering the value also in the call to panic(), drop it
there for being static and hence easy to determine without being part
of the panic message.
While working on XSA-361 and its follow-ups, I failed to spot another
place where the kernel mapping part of an operation was not treated the
same as the user space part. Detect and propagate errors and add a 2nd
pr_debug().
Fix get_run_delay() to check fscanf() return value to get rid of the
following warning. When fscanf() fails return MIN_RUN_DELAY_NS from
get_run_delay(). Move MIN_RUN_DELAY_NS from steal_time.c to test_util.h
so get_run_delay() and steal_time.c can use it.
lib/test_util.c: In function ‘get_run_delay’:
lib/test_util.c:316:2: warning: ignoring return value of ‘fscanf’ declared with attribute ‘warn_unused_result’ [-Wunused-result]
316 | fscanf(fp, "%ld %ld ", &val[0], &val[1]);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix get_trans_hugepagesz() to check fscanf() return value to get rid
of the following warning:
lib/test_util.c: In function ‘get_trans_hugepagesz’:
lib/test_util.c:138:2: warning: ignoring return value of ‘fscanf’ declared with attribute ‘warn_unused_result’ [-Wunused-result]
138 | fscanf(f, "%ld", &size);
| ^~~~~~~~~~~~~~~~~~~~~~~
Fix get_warnings_count() to check fscanf() return value to get rid
of the following warning:
x86_64/mmio_warning_test.c: In function ‘get_warnings_count’:
x86_64/mmio_warning_test.c:85:2: warning: ignoring return value of ‘fscanf’ declared with attribute ‘warn_unused_result’ [-Wunused-result]
85 | fscanf(f, "%d", &warnings);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
LKP/0Day reported some building errors about kvm, and errors message
are not always same:
- lib/x86_64/processor.c:1083:31: error: ‘KVM_CAP_NESTED_STATE’ undeclared
(first use in this function); did you mean ‘KVM_CAP_PIT_STATE2’?
- lib/test_util.c:189:30: error: ‘MAP_HUGE_16KB’ undeclared (first use
in this function); did you mean ‘MAP_HUGE_16GB’?
Although kvm relies on the khdr, they still be built in parallel when -j
is specified. In this case, it will cause compiling errors.
Here we mark target khdr as NOTPARALLEL to make it be always built
first.
CC: Philip Li <philip.li@intel.com> Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
1. Add missing configuration of the SM RR registers in the DMA_IF.
2. Remove HBW range that doesn't belong.
3. Add entire gap + DBG area, from end of TPC7 to end of entire
DBG space.
As collective wait operation is required only when NIC ports are
available, we disable the option to submit a CS in case all the ports
are disabled, which is the current situation in the upstream driver.
Due to FLR scenario when running inside a VM, we must not use indirect
MSI because it might cause some issues on VM destroy.
In a VM we use single MSI mode in contrary to multi MSI mode which is
used in bare-metal.
Hence direct MSI should be used in single MSI mode only.
testusb' application which uses 'usbtest' driver reports 'unknown speed'
from the function 'find_testdev'. The variable 'entry->speed' was not
updated from the application. The IOCTL mentioned in the FIXME comment can
only report whether the connection is low speed or not. Speed is read using
the IOCTL USBDEVFS_GET_SPEED which reports the proper speed grade. The
call is implemented in the function 'handle_testdev' where the file
descriptor was availble locally. Sample output is given below where 'high
speed' is printed as the connected speed.
sudo ./testusb -a
high speed /dev/bus/usb/001/011 0
/dev/bus/usb/001/011 test 0, 0.000015 secs
/dev/bus/usb/001/011 test 1, 0.194208 secs
/dev/bus/usb/001/011 test 2, 0.077289 secs
/dev/bus/usb/001/011 test 3, 0.170604 secs
/dev/bus/usb/001/011 test 4, 0.108335 secs
/dev/bus/usb/001/011 test 5, 2.788076 secs
/dev/bus/usb/001/011 test 6, 2.594610 secs
/dev/bus/usb/001/011 test 7, 2.905459 secs
/dev/bus/usb/001/011 test 8, 2.795193 secs
/dev/bus/usb/001/011 test 9, 8.372651 secs
/dev/bus/usb/001/011 test 10, 6.919731 secs
/dev/bus/usb/001/011 test 11, 16.372687 secs
/dev/bus/usb/001/011 test 12, 16.375233 secs
/dev/bus/usb/001/011 test 13, 2.977457 secs
/dev/bus/usb/001/011 test 14 --> 22 (Invalid argument)
/dev/bus/usb/001/011 test 17, 0.148826 secs
/dev/bus/usb/001/011 test 18, 0.068718 secs
/dev/bus/usb/001/011 test 19, 0.125992 secs
/dev/bus/usb/001/011 test 20, 0.127477 secs
/dev/bus/usb/001/011 test 21 --> 22 (Invalid argument)
/dev/bus/usb/001/011 test 24, 4.133763 secs
/dev/bus/usb/001/011 test 27, 2.140066 secs
/dev/bus/usb/001/011 test 28, 2.120713 secs
/dev/bus/usb/001/011 test 29, 0.507762 secs
After a device is initialized via device_initialize() it should be freed
via put_device(). sd_probe() currently gets this wrong, fix it up.
Link: https://lore.kernel.org/r/20210906090112.531442-1-ming.lei@redhat.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Ming Lei <ming.lei@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Device manager releases device-specific resources when a driver
disconnects from a device, devm_memunmap_pages and
devm_release_mem_region calls in svm_migrate_fini are redundant.
It causes below warning trace after patch "drm/amdgpu: Split
amdgpu_device_fini into early and late", so remove function
svm_migrate_fini.
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If svm migration init failed to create pgmap for device memory, set
pgmap type to 0 to disable device SVM support capability.
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Guenter reported [1] that the pci_iounmap() changes remain problematic,
with sparc64 allnoconfig and tinyconfig still not building due to the
header file changes and confusion with the arch-specific pci_iounmap()
implementation.
I'm pretty convinced that sparc should just use GENERIC_IOMAP instead of
doing its own thing, since it turns out that the sparc64 version of
pci_iounmap() is somewhat buggy (see [2]). But in the meantime, this
just fixes the build by avoiding the trivial re-definition of the empty
case.
When re-entering the main loop of xenvif_tx_check_gop() a 2nd time, the
special considerations for the head of the SKB no longer apply. Don't
mistakenly report ERROR to the frontend for the first entry in the list,
even if - from all I can tell - this shouldn't matter much as the overall
transmit will need to be considered failed anyway.
Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Paul Durrant <paul@xen.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
MDIO-attached devices might have interrupts and other things that might
need quiesced when we kexec into a new kernel. Things are even more
creepy when those interrupt lines are shared, and in that case it is
absolutely mandatory to disable all interrupt sources.
Moreover, MDIO devices might be DSA switches, and DSA needs its own
shutdown method to unlink from the DSA master, which is a new
requirement that appeared after commit 2f1e8ea726e9 ("net: dsa: link
interfaces with the DSA master to get rid of lockdep warnings").
So introduce a ->shutdown method in the MDIO device driver structure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When we get an error flushing one device, during a super block commit, we
record the error in the device structure, in the field 'last_flush_error'.
This is used to later check if we should error out the super block commit,
depending on whether the number of flush errors is greater than or equals
to the maximum tolerated device failures for a raid profile.
However if we get a transient device flush error, unmount the filesystem
and later try to mount it, we can fail the mount because we treat that
past error as critical and consider the device is missing. Even if it's
very likely that the error will happen again, as it's probably due to a
hardware related problem, there may be cases where the error might not
happen again. One example is during testing, and a test case like the
new generic/648 from fstests always triggers this. The test cases
generic/019 and generic/475 also trigger this scenario, but very
sporadically.
When this happens we get an error like this:
$ mount /dev/sdc /mnt
mount: /mnt wrong fs type, bad option, bad superblock on /dev/sdc, missing codepage or helper program, or other error.
$ dmesg
(...)
[12918.886926] BTRFS warning (device sdc): chunk 13631488 missing 1 devices, max tolerance is 0 for writable mount
[12918.888293] BTRFS warning (device sdc): writable mount is not allowed due to too many missing devices
[12918.890853] BTRFS error (device sdc): open_ctree failed
The failure happens because when btrfs_check_rw_degradable() is called at
mount time, or at remount from RO to RW time, is sees a non zero value in
a device's ->last_flush_error attribute, and therefore considers that the
device is 'missing'.
Fix this by setting a device's ->last_flush_error to zero when we close a
device, making sure the error is not seen on the next mount attempt. We
only need to track flush errors during the current mount, so that we never
commit a super block if such errors happened.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a BUG_ON() in btrfs_csum_one_bio() to catch code logic error.
It has indeed caught several bugs during subpage development.
But the BUG_ON() itself will bring down the whole system which is
an overkill.
Replace it with a WARN() and exit gracefully, so that it won't crash the
whole system while we can still catch the code logic error.
Signed-off-by: Qu Wenruo <wqu@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the back channel enters SEQ4_STATUS_CB_PATH_DOWN state, the client
recovers by sending BIND_CONN_TO_SESSION but the server fails to recover
the back channel and leaves it as NFSD4_CB_DOWN.
Fix by enhancing nfsd4_bind_conn_to_session to probe the back channel
by calling nfsd4_probe_callback.
Signed-off-by: Dai Ngo <dai.ngo@oracle.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add info for getting the firmware directly from the UEFI for the Chuwi Hi10
Plus (CWI527), so that the user does not need to manually install the
firmware in /lib/firmware/silead.
This change will make the touchscreen on these devices work OOTB,
without requiring any manual setup.
Also tweak the min and width/height values a bit for more accurate position
reporting.
Add touchscreen info for the Chuwi HiBook (CWI514) tablet. This includes
info for getting the firmware directly from the UEFI, so that the user does
not need to manually install the firmware in /lib/firmware/silead.
This change will make the touchscreen on these devices work OOTB,
without requiring any manual setup.
afs_d_revalidate() should only be validating the directory entry it is
given and the directory to which that belongs; it shouldn't be validating
the inode/vnode to which that dentry points. Besides, validation need to
be done even if we don't call afs_d_revalidate() - which might be the case
if we're starting from a file descriptor.
In order for afs_d_revalidate() to be fixed, validation points must be
added in some other places. Certain directory operations, such as
afs_unlink(), already check this, but not all and not all file operations
either.
Note that the validation of a vnode not only checks to see if the
attributes we have are correct, but also gets a promise from the server to
notify us if that file gets changed by a third party.
Add the following checks:
- Check the vnode we're going to make a hard link to.
- Check the vnode we're going to move/rename.
- Check the vnode we're going to read from.
- Check the vnode we're going to write to.
- Check the vnode we're going to sync.
- Check the vnode we're going to make a mapped page writable for.
Some of these aren't strictly necessary as we're going to perform a server
operation that might get the attributes anyway from which we can determine
if something changed - though it might not get us a callback promise.
Previously zero length transfers submitted to the Rokchip SPI driver would
time out in the SPI layer. This happens because the SPI peripheral does
not trigger a transfer completion interrupt for zero length transfers.
Fix that by completing zero length transfers immediately at start of
transfer.
The objtool warning that the kvm instruction emulation code triggered
wasn't very useful:
arch/x86/kvm/emulate.o: warning: objtool: __ex_table+0x4: don't know how to handle reloc symbol type: kvm_fastop_exception
in that it helpfully tells you which symbol name it had trouble figuring
out the relocation for, but it doesn't actually say what the unknown
symbol type was that triggered it all.
In this case it was because of missing type information (type 0, aka
STT_NOTYPE), but on the whole it really should just have printed that
out as part of the message.
Because if this warning triggers, that's very much the first thing you
want to know - why did reloc2sec_off() return failure for that symbol?
So rather than just saying you can't handle some type of symbol without
saying what the type _was_, just print out the type number too.
Check the return of init_srcu_struct(), which can fail due to OOM, when
initializing the page track mechanism. Lack of checking leads to a NULL
pointer deref found by a modified syzkaller.
Reported-by: TCS Robot <tcs_robot@tencent.com> Signed-off-by: Haimin Zhang <tcs_kernel@tencent.com>
Message-Id: <1630636626-12262-1-git-send-email-tcs_kernel@tencent.com>
[Move the call towards the beginning of kvm_arch_init_vm. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xts_crypt() code doesn't call kernel_fpu_end() after calling
kernel_fpu_begin() if walk.nbytes is 0. The correct behavior should be
not calling kernel_fpu_begin() if walk.nbytes is 0.
'kvmalloc()' is a convenience function for people who want to do a
kmalloc() but fall back on vmalloc() if there aren't enough physically
contiguous pages, or if the allocation is larger than what kmalloc()
supports.
However, let's make sure it doesn't get _too_ easy to do crazy things
with it. In particular, don't allow big allocations that could be due
to integer overflow or underflow. So make sure the allocation size fits
in an 'int', to protect against trivial integer conversion issues.
Syzbot reported slab-out-of-bounds Write bug in hid-betopff driver.
The problem is the driver assumes the device must have an input report but
some malicious devices violate this assumption.
So this patch checks hid_device's input is non empty before it's been used.
There are two invocation sites of hso_free_net_device. After
refactoring hso_create_net_device, this parameter is useless.
Remove the bailout in the hso_free_net_device and change the invocation
sites of this function.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
[Backport this cleanup patch to 5.10 and 5.14 in order to keep the
codebase consistent with the 4.14/4.19/5.4 patchseries] Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a nuisance when CONFIG_WERROR is set, so drop the variable
declaration since the code that used it was removed.
../arch/nios2/kernel/setup.c: In function 'setup_arch':
../arch/nios2/kernel/setup.c:152:13: warning: unused variable 'dram_start' [-Wunused-variable]
152 | int dram_start;
Fixes: 7f7bc20bc41a ("nios2: Don't use _end for calculating min_low_pfn") Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Reported-by: kernel test robot <lkp@intel.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Cc: Andreas Oetken <andreas.oetken@siemens.com> Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
up->corkflag field can be read or written without any lock.
Annotate accesses to avoid possible syzbot/KCSAN reports.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the actual_length calculation is performed unsigned, packets
shorter than 7 bytes (e.g. packets without data or otherwise truncated)
or non-received packets ("zero" bytes) can cause buffer overflow.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214437 Fixes: 42337b9d4d958("HID: add driver for U2F Zero built-in LED and RNG") Signed-off-by: Andrej Shadura <andrew.shadura@collabora.co.uk> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error path in ext4_fill_super forget to flush s_error_work before
journal destroy, and it may trigger the follow bug since
flush_stashed_error_work can run concurrently with journal destroy
without any protection for sbi->s_journal.
static int start_this_handle(...)
BUG_ON(journal->j_flags & JBD2_UNMOUNT); <---- Trigger this
Besides, after we enable fast commit, ext4_fc_replay can add work to
s_error_work but return success, so the latter journal destroy in
ext4_load_journal can trigger this problem too.
Fix this problem with two steps:
1. Call ext4_commit_super directly in ext4_handle_error for the case
that called from ext4_fc_replay
2. Since it's hard to pair the init and flush for s_error_work, we'd
better add a extras flush_work before journal destroy in
ext4_fill_super
Besides, this patch will call ext4_commit_super in ext4_handle_error for
any nojournal case too. But it seems safe since the reason we call
schedule_work was that we should save error info to sb through journal
if available. Conversely, for the nojournal case, it seems useless delay
commit superblock to s_error_work.
Fixes: c92dc856848f ("ext4: defer saving error info from atomic context") Fixes: 2d01ddc86606 ("ext4: save error info to sb through journal if available") Cc: stable@kernel.org Signed-off-by: yangerkun <yangerkun@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Link: https://lore.kernel.org/r/20210924093917.1953239-1-yangerkun@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When ext4_htree_fill_tree() fails, ext4_dx_readdir() can run into an
infinite loop since if info->last_pos != ctx->pos this will reset the
directory scan and reread the failing entry. For example:
1. a dx_dir which has 3 block, block 0 as dx_root block, block 1/2 as
leaf block which own the ext4_dir_entry_2
2. block 1 read ok and call_filldir which will fill the dirent and update
the ctx->pos
3. block 2 read fail, but we has already fill some dirent, so we will
return back to userspace will a positive return val(see ksys_getdents64)
4. the second ext4_dx_readdir will reset the world since info->last_pos
!= ctx->pos, and will also init the curr_hash which pos to block 1
5. So we will read block1 too, and once block2 still read fail, we can
only fill one dirent because the hash of the entry in block1(besides
the last one) won't greater than curr_hash
6. this time, we forget update last_pos too since the read for block2
will fail, and since we has got the one entry, ksys_getdents64 can
return success
7. Latter we will trapped in a loop with step 4~6
Cc: stable@kernel.org Signed-off-by: yangerkun <yangerkun@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Signed-off-by: Theodore Ts'o <tytso@mit.edu> Link: https://lore.kernel.org/r/20210914111415.3921954-1-yangerkun@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the call to ext4_map_blocks() fails due to an corrupted file
system, ext4_ext_replay_set_iblocks() can get stuck in an infinite
loop. This could be reproduced by running generic/526 with a file
system that has inline_data and fast_commit enabled. The system will
repeatedly log to the console:
EXT4-fs warning (device dm-3): ext4_block_to_path:105: block 1074800922 > max in inode 131076
With this patch, generic/526 still fails, but system is no longer
locking up in a tight loop. It's likely the root casue is that
fast_commit replay is corrupting file systems with inline_data, and we
probably need to add better error handling in the fast commit replay
code path beyond what is done here, which essentially just breaks the
infinite loop without reporting the to the higher levels of the code.
When ext4_insert_delayed block receives and recovers from an error from
ext4_es_insert_delayed_block(), e.g., ENOMEM, it does not release the
space it has reserved for that block insertion as it should. One effect
of this bug is that s_dirtyclusters_counter is not decremented and
remains incorrectly elevated until the file system has been unmounted.
This can result in premature ENOSPC returns and apparent loss of free
space.
Another effect of this bug is that
/sys/fs/ext4/<dev>/delayed_allocation_blocks can remain non-zero even
after syncfs has been executed on the filesystem.
Besides, add check for s_dirtyclusters_counter when inode is going to be
evicted and freed. s_dirtyclusters_counter can still keep non-zero until
inode is written back in .evict_inode(), and thus the check is delayed
to .destroy_inode().
Now EXT4_FC_TAG_ADD_RANGE uses ext4_extent to track the
newly-added blocks, but the limit on the max value of
ee_len field is ignored, and it can lead to BUG_ON as
shown below when running command "fallocate -l 128M file"
on a fast_commit-enabled fs:
We should use unsigned long long rather than loff_t to avoid
overflow in ext4_max_bitmap_size() for comparison before returning.
w/o this patch sbi->s_bitmap_maxbytes was becoming a negative
value due to overflow of upper_limit (with has_huge_files as true)
Below is a quick test to trigger it on a 64KB pagesize system.
sudo mkfs.ext4 -b 65536 -O ^has_extents,^64bit /dev/loop2
sudo mount /dev/loop2 /mnt
sudo echo "hello" > /mnt/hello -> This will error out with
"echo: write error: File too large"
Registration of the ipoctal tty devices is unlikely to fail, but if it
ever does, make sure not to deregister a never registered tty device
(and dereference a NULL pointer) when the driver is later unbound.
The tty driver name is used also after registering the driver and must
specifically not be allocated on the stack to avoid leaking information
to user space (or triggering an oops).
Drivers should not try to encode topology information in the tty device
name but this one snuck in through staging without anyone noticing and
another driver has since copied this malpractice.
Fixing the ABI is a separate issue, but this at least plugs the security
hole.
Fixes: ba4dc61fe8c5 ("Staging: ipack: add support for IP-OCTAL mezzanine board") Cc: stable@vger.kernel.org # 3.5 Acked-by: Samuel Iglesias Gonsalvez <siglesias@igalia.com> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20210917114622.5412-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Where,
* Indentation denotes "child of" parent in previous line.
* X -> Y denotes X is consumer of Y based on firmware (Eg: DT).
We have cyclic dependency: device-A -> device-C -> device-B -> device-A
fw_devlink current treats device-C -> device-B dependency as an invalid
dependency and doesn't enforce it but leaves the rest of the
dependencies as is.
While the current behavior is necessary, it is not sufficient if the
false dependency in this example is actually device-A -> device-C. When
this is the case, device-C will correctly probe defer waiting for
device-B to be added, but device-A will be incorrectly probe deferred by
fw_devlink waiting on device-C to probe successfully. Due to this, none
of the devices in the cycle will end up probing.
To fix this, we need to go relax all the dependencies in the cycle like
we already do in the other instances where fw_devlink detects cycles.
A real world example of this was reported[1] and analyzed[2].
In commit b212921b13bd ("elf: don't use MAP_FIXED_NOREPLACE for elf
executable mappings") we still leave MAP_FIXED_NOREPLACE in place for
load_elf_interp.
Unfortunately, this will cause kernel to fail to start with:
1 (init): Uhuuh, elf segment at 00003ffff7ffd000 requested but the memory is mapped already
Failed to execute /init (error -17)
The reason is that the elf interpreter (ld.so) has overlapping segments.
readelf -l ld-2.31.so
Program Headers:
Type Offset VirtAddr PhysAddr
FileSiz MemSiz Flags Align
LOAD 0x0000000000000000 0x0000000000000000 0x0000000000000000
0x000000000002c94c 0x000000000002c94c R E 0x10000
LOAD 0x000000000002dae0 0x000000000003dae0 0x000000000003dae0
0x00000000000021e8 0x0000000000002320 RW 0x10000
LOAD 0x000000000002fe00 0x000000000003fe00 0x000000000003fe00
0x00000000000011ac 0x0000000000001328 RW 0x10000
The reason for this problem is the same as described in commit ad55eac74f20 ("elf: enforce MAP_FIXED on overlaying elf segments").
Not only executable binaries, elf interpreters (e.g. ld.so) can have
overlapping elf segments, so we better drop MAP_FIXED_NOREPLACE and go
back to MAP_FIXED in load_elf_interp.
Fixes: 4ed28639519c ("fs, elf: drop MAP_FIXED usage from elf_map") Cc: <stable@vger.kernel.org> # v4.19 Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Michal Hocko <mhocko@suse.com> Signed-off-by: Chen Jingwen <chenjingwen6@huawei.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some apple controllers use the command id as an index to implementation
specific data structures and will fail if the value is out of bounds.
The nvme driver's recently introduced command sequence number breaks
this controller.
Provide a quirk so these spec incompliant controllers can function as
before. The driver will not have the ability to detect bad completions
when this quirk is used, but we weren't previously checking this anyway.
The quirk bit was selected so that it can readily apply to stable.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=214509 Cc: Sven Peter <sven@svenpeter.dev> Reported-by: Orlando Chamberlain <redecorating@protonmail.com> Reported-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Tested-by: Sven Peter <sven@svenpeter.dev> Link: https://lore.kernel.org/r/20210927154306.387437-1-kbusch@kernel.org Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The recent change to make objtool aware of more symbol relocation types
(commit 24ff65257375: "objtool: Teach get_alt_entry() about more
relocation types") also added another check, and resulted in this
objtool warning when building kvm on x86:
arch/x86/kvm/emulate.o: warning: objtool: __ex_table+0x4: don't know how to handle reloc symbol type: kvm_fastop_exception
The reason seems to be that kvm_fastop_exception() is marked as a global
symbol, which causes the relocation to ke kept around for objtool. And
at the same time, the kvm_fastop_exception definition (which is done as
an inline asm statement) doesn't actually set the type of the global,
which then makes objtool unhappy.
The minimal fix is to just not mark kvm_fastop_exception as being a
global symbol. It's only used in that one compilation unit anyway, so
it was always pointless. That's how all the other local exception table
labels are done.
I'm not entirely happy about the kinds of games that the kvm code plays
with doing its own exception handling, and the fact that it confused
objtool is most definitely a symptom of the code being a bit too subtle
and ad-hoc. But at least this trivial one-liner makes objtool no longer
upset about what is going on.
Fixes: 24ff65257375 ("objtool: Teach get_alt_entry() about more relocation types") Link: https://lore.kernel.org/lkml/CAHk-=wiZwq-0LknKhXN4M+T8jbxn_2i9mcKpO+OaBSSq_Eh7tg@mail.gmail.com/ Cc: Borislav Petkov <bp@suse.de> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Sean Christopherson <seanjc@google.com> Cc: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Wanpeng Li <wanpengli@tencent.com> Cc: Jim Mattson <jmattson@google.com> Cc: Joerg Roedel <joro@8bytes.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The P10 (temp sensor version 0x10) doesn't do the same VRM status
reporting that was used on P9. It just reports the temperature, so
drop the check for VRM fru type in the sysfs show function, and don't
set the name to "alarm".
Fixes: db4919ec86 ("hwmon: (occ) Add new temperature sensor type") Signed-off-by: Eddie James <eajames@linux.ibm.com> Link: https://lore.kernel.org/r/20210929153604.14968-1-eajames@linux.ibm.com Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit a7b359fc6a37 ("sched/fair: Correctly insert cfs_rq's to
list on unthrottle") we add cfs_rqs with no runnable tasks but not fully
decayed into the load (leaf) list. We may ignore adding some ancestors
and therefore breaking tmp_alone_branch invariant. This broke LTP test
cfs_bandwidth01 and it was partially fixed in commit fdaba61ef8a2
("sched/fair: Ensure that the CFS parent is added after unthrottling").
I noticed the named test still fails even with the fix (but with low
probability, 1 in ~1000 executions of the test). The reason is when
bailing out of unthrottle_cfs_rq early, we may miss adding ancestors of
the unthrottled cfs_rq, thus, not joining tmp_alone_branch properly.
Fix this by adding ancestors if we notice the unthrottled cfs_rq was
added to the load list.
Fixes: a7b359fc6a37 ("sched/fair: Correctly insert cfs_rq's to list on unthrottle") Signed-off-by: Michal Koutný <mkoutny@suse.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Vincent Guittot <vincent.guittot@linaro.org> Reviewed-by: Odin Ugedal <odin@uged.al> Link: https://lore.kernel.org/r/20210917153037.11176-1-mkoutny@suse.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Occasionally objtool encounters symbol (as opposed to section)
relocations in .altinstructions. Typically they are the alternatives
written by elf_add_alternative() as encountered on a noinstr
validation run on vmlinux after having already ran objtool on the
individual .o files.
Basically this is the counterpart of commit 44f6a7c0755d ("objtool:
Fix seg fault with Clang non-section symbols"), because when these new
assemblers (binutils now also does this) strip the section symbols,
elf_add_reloc_to_insn() is forced to emit symbol based relocations.
As such, teach get_alt_entry() about different relocation types.
Jann Horn reported that SO_PEERCRED and SO_PEERGROUPS implementations
are racy, as af_unix can concurrently change sk_peer_pid and sk_peer_cred.
In order to fix this issue, this patch adds a new spinlock that needs
to be used whenever these fields are read or written.
Jann also pointed out that l2cap_sock_get_peer_pid_cb() is currently
reading sk->sk_peer_pid which makes no sense, as this field
is only possibly set by AF_UNIX sockets.
We will have to clean this in a separate patch.
This could be done by reverting b48596d1dc25 "Bluetooth: L2CAP: Add get_peer_pid callback"
or implementing what was truly expected.
Fixes: 109f6e39fa07 ("af_unix: Allow SO_PEERCRED to work across namespaces.") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: Jann Horn <jannh@google.com> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When STMMAC is paired with Energy-Efficient Ethernet(EEE) capable PHY,
and the PHY is advertising EEE by default, we need to enable EEE on the
xPCS side too, instead of having user to manually trigger the enabling
config via ethtool.
Fixed this by adding xpcs_config_eee() call in stmmac_eee_init().
Fixes: 7617af3d1a5e ("net: pcs: Introducing support for DWC xpcs Energy Efficient Ethernet") Cc: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com> Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Patch that refactored fl_walk() to use idr_for_each_entry_continue_ul()
also removed rcu protection of individual filters which causes following
use-after-free when filter is deleted concurrently. Fix fl_walk() to obtain
rcu read lock while iterating and taking the filter reference and temporary
release the lock while calling arg->fn() callback that can sleep.
KASAN trace:
[ 352.773640] ==================================================================
[ 352.775041] BUG: KASAN: use-after-free in fl_walk+0x159/0x240 [cls_flower]
[ 352.776304] Read of size 4 at addr ffff8881c8251480 by task tc/2987
When EEE support was added to the 28nm EPHY it was assumed that it would
be able to support the standard clause 45 over clause 22 register access
method. It turns out that the PHY does not support that, which is the
very reason for using the indirect shadow mode 2 bank 3 access method.
Implement {read,write}_mmd to allow the standard PHY library routines
pertaining to EEE querying and configuration to work correctly on these
PHYs. This forces us to implement a __phy_set_clr_bits() function that
does not grab the MDIO bus lock since the PHY driver's {read,write}_mmd
functions are always called with that lock held.
Fixes: 83ee102a6998 ("net: phy: bcm7xxx: add support for 28nm EPHY") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the firmware compatible features are enabled in PF driver
initialization process, but they are not disabled in PF driver
deinitialization process and firmware keeps these features in enabled
status.
In this case, if load an old PF driver (for example, in VM) which not
support the firmware compatible features, firmware will still send mailbox
message to PF when link status changed and PF will print
"un-supported mailbox message, code = 201".
To fix this problem, disable these firmware compatible features in PF
driver deinitialization process.
Fixes: ed8fb4b262ae ("net: hns3: add link change event report") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, the rx vlan filter will always be disabled before selftest and
be enabled after selftest as the rx vlan filter feature is fixed on in
old device earlier than V3.
However, this feature is not fixed in some new devices and it can be
disabled by user. In this case, it is wrong if rx vlan filter is enabled
after selftest. So fix it.
Fixes: bcc26e8dc432 ("net: hns3: remove unused code in hns3_self_test()") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch reconstructs function hns3_self_test to reduce the code
cycle complexity and make code more concise.
Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, if function adds an existing unicast mac address, eventhough
driver will not add this address into hardware, but it will return 0 in
function hclge_add_uc_addr_common(). It will cause the state of this
unicast mac address is ACTIVE in driver, but it should be in TO-ADD state.
To fix this problem, function hclge_add_uc_addr_common() returns -EEXIST
if mac address is existing, and delete two error log to avoid printing
them all the time after this modification.
Fixes: 72110b567479 ("net: hns3: return 0 and print warning when hit duplicate MAC") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
HCLGE_FLAG_MQPRIO_ENABLE is supposed to set when enable
multiple TCs with tc mqprio, and HCLGE_FLAG_DCB_ENABLE is
supposed to set when enable multiple TCs with ets. But
the driver mixed the flags when updating the tm configuration.
Furtherly, PFC should be available when HCLGE_FLAG_MQPRIO_ENABLE
too, so remove the unnecessary limitation.
Fixes: 5a5c90917467 ("net: hns3: add support for tc mqprio offload") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
For destroy mqprio is irreversible in stack, so it's unnecessary
to rollback the tc configuration when destroy mqprio failed.
Otherwise, it may cause the configuration being inconsistent
between driver and netstack.
As the failure is usually caused by reset, and the driver will
restore the configuration after reset, so it can keep the
configuration being consistent between driver and hardware.
Fixes: 5a5c90917467 ("net: hns3: add support for tc mqprio offload") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, in function hns3_nic_set_real_num_queue(), the
driver doesn't report the queue count and offset for disabled
tc. If user enables multiple TCs, but only maps user
priorities to partial of them, it may cause the queue range
of the unmapped TC being displayed abnormally.
Fix it by removing the tc enable checking, ensure the queue
count is not zero.
With this change, the tc_en is useless now, so remove it.
Fixes: a75a8efa00c5 ("net: hns3: Fix tc setup when netdev is first up") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
hns3_nic_net_open() is not allowed to called repeatly, but there
is no checking for this. When doing device reset and setup tc
concurrently, there is a small oppotunity to call hns3_nic_net_open
repeatedly, and cause kernel bug by calling napi_enable twice.
The calltrace information is like below:
[ 3078.222780] ------------[ cut here ]------------
[ 3078.230255] kernel BUG at net/core/dev.c:6991!
[ 3078.236224] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 3078.243431] Modules linked in: hns3 hclgevf hclge hnae3 vfio_iommu_type1 vfio_pci vfio_virqfd vfio pv680_mii(O)
[ 3078.258880] CPU: 0 PID: 295 Comm: kworker/u8:5 Tainted: G O 5.14.0-rc4+ #1
[ 3078.269102] Hardware name: , BIOS KpxxxFPGA 1P B600 V181 08/12/2021
[ 3078.276801] Workqueue: hclge hclge_service_task [hclge]
[ 3078.288774] pstate: 60400009 (nZCv daif +PAN -UAO -TCO BTYPE=--)
[ 3078.296168] pc : napi_enable+0x80/0x84
tc qdisc sho[w 3d0e7v8 .e3t0h218 79] lr : hns3_nic_net_open+0x138/0x510 [hns3]
Once hns3_nic_net_open() is excute success, the flag
HNS3_NIC_STATE_DOWN will be cleared. So add checking for this
flag, directly return when HNS3_NIC_STATE_DOWN is no set.
Fixes: e888402789b9 ("net: hns3: call hns3_nic_net_open() while doing HNAE3_UP_CLIENT") Signed-off-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The ixgbe driver currently generates a NULL pointer dereference with
some machine (online cpus < 63). This is due to the fact that the
maximum value of num_xdp_queues is nr_cpu_ids. Code is in
"ixgbe_set_rss_queues"".
Here's how the problem repeats itself:
Some machine (online cpus < 63), And user set num_queues to 63 through
ethtool. Code is in the "ixgbe_set_channels",
adapter->ring_feature[RING_F_FDIR].limit = count;
It becomes 63.
When user use xdp, "ixgbe_set_rss_queues" will set queues num.
adapter->num_rx_queues = rss_i;
adapter->num_tx_queues = rss_i;
adapter->num_xdp_queues = ixgbe_xdp_queues(adapter);
And rss_i's value is from
f = &adapter->ring_feature[RING_F_FDIR];
rss_i = f->indices = f->limit;
So "num_rx_queues" > "num_xdp_queues", when run to "ixgbe_xdp_setup",
for (i = 0; i < adapter->num_rx_queues; i++)
if (adapter->xdp_ring[i]->xsk_umem)
So I fix ixgbe_max_channels so that it will not allow a setting of queues
to be higher than the num_online_cpus(). And when run to ixgbe_xdp_setup,
take the smaller value of num_rx_queues and num_xdp_queues.
Fixes: 4a9b32f30f80 ("ixgbe: fix potential RX buffer starvation for AF_XDP") Signed-off-by: Feng Zhou <zhoufeng.zf@bytedance.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log