When resuming from low power, the driver attempts to restore the
configuration of some pins. This is done by a call to:
stm32_pinctrl_restore_gpio_regs(struct stm32_pinctrl *pctl, u32 pin)
where 'pin' must be a valid pin value (i.e. matching some 'groups->pin').
Fix the current implementation which uses some wrong 'pin' value.
tglx notes:
This function [futex_detect_cmpxchg] is only needed when an
architecture has to runtime discover whether the CPU supports it or
not. ARM has unconditional support for this, so the obvious thing to
do is the below.
Fixes linkage failure from Clang randconfigs:
kernel/futex.o:(.text.fixup+0x5c): relocation truncated to fit: R_ARM_JUMP24 against `.init.text'
and boot failures for CONFIG_THUMB2_KERNEL.
We have the same LAN controller on different PCHs. Separate TGP board
type from SPT which will allow for specific fixes to be applied for
TGP platforms.
Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by: Sasha Neftin <sasha.neftin@intel.com> Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de> Tested-by: Mark Pearson <markpearson@lenovo.com> Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reported-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com Signed-off-by: Yanfei Xu <yanfei.xu@windriver.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
BPF test infra has some hacks in place which kzalloc() a socket and perform
minimum init via sock_net_set() and sock_init_data(). As a result, the sk's
skcd->cgroup is NULL since it didn't go through proper initialization as it
would have been the case from sk_alloc(). Rather than re-adding a NULL test
in sock_cgroup_ptr() just for this, use sk_{alloc,free}() pair for the test
socket. The latter also allows to get rid of the bpf_sk_storage_free() special
case.
Fixes: 8520e224f547 ("bpf, cgroups: Fix cgroup v2 fallback on v1/v2 mixed mode") Fixes: b7a1848e8398 ("bpf: add BPF_PROG_TEST_RUN support for flow dissector") Fixes: 2cb494a36c98 ("bpf: add tests for direct packet access from CGROUP_SKB") Reported-by: syzbot+664b58e9a40fbb2cec71@syzkaller.appspotmail.com Reported-by: syzbot+33f36d0754d4c5c0e102@syzkaller.appspotmail.com Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Tested-by: syzbot+664b58e9a40fbb2cec71@syzkaller.appspotmail.com Tested-by: syzbot+33f36d0754d4c5c0e102@syzkaller.appspotmail.com Link: https://lore.kernel.org/bpf/20210927123921.21535-2-daniel@iogearbox.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 2a671f77ee49 ("s390/pci: fix use after free of zpci_dev")
the reference count of a zpci_dev is incremented between
pcibios_add_device() and pcibios_release_device() which was supposed to
prevent the zpci_dev from being freed while the common PCI code has
access to it. It was missed however that the handling of zPCI
availability events assumed that once zpci_zdev_put() was called no
later availability event would still see the device. With the previously
mentioned commit however this assumption no longer holds and we must
make sure that we only drop the initial long-lived reference the zPCI
subsystem holds exactly once.
Do so by introducing a zpci_device_reserved() function that handles when
a device is reserved. Here we make sure the zpci_dev will not be
considered for further events by removing it from the zpci_list.
This also means that the device actually stays in the
ZPCI_FN_STATE_RESERVED state between the time we know it has been
reserved and the final reference going away. We thus need to consider it
a real state instead of just a conceptual state after the removal. The
final cleanup of PCI resources, removal from zbus, and destruction of
the IOMMU stays in zpci_release_device() to make sure holders of the
reference do see valid data until the release.
Fixes: 2a671f77ee49 ("s390/pci: fix use after free of zpci_dev") Cc: stable@vger.kernel.org Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's currently safe to call zpci_cleanup_bus_resources() even if the
resources were never created but it makes no sense so check
zdev->has_resources before we call zpci_cleanup_bus_resources() in
zpci_release_device().
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Acked-by: Pierre Morel <pmorel@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit ea2f0f77538c ("scsi: core: Cap scsi_host cmd_per_lun at
can_queue"), a 416-CPU VM running on Hyper-V hangs during boot because the
hv_storvsc driver sets scsi_driver.can_queue to an integer value that
exceeds SHRT_MAX, and hence scsi_add_host_with_dma() sets
shost->cmd_per_lun to a negative "short" value.
Use min_t(int, ...) to work around the issue.
Link: https://lore.kernel.org/r/20211008043546.6006-1-decui@microsoft.com Fixes: ea2f0f77538c ("scsi: core: Cap scsi_host cmd_per_lun at can_queue") Cc: stable@vger.kernel.org Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Reviewed-by: Ming Lei <ming.lei@redhat.com> Reviewed-by: John Garry <john.garry@huawei.com> Signed-off-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a mistake in commit 2be7828c9fefc ("get rid of autofs_getpath()")
that affects kernels from v5.13.0, basically missed because of me not
fully testing the change for Al.
The problem is that the hash calculation for the wait name qstr hasn't
been updated to account for the change to use dentry_path_raw(). This
prevents the correct matching an existing wait resulting in multiple
notifications being sent to the daemon for the same mount which must
not occur.
The problem wasn't discovered earlier because it only occurs when
multiple processes trigger a request for the same mount concurrently
so it only shows up in more aggressive testing.
Fixes: 2be7828c9fefc ("get rid of autofs_getpath()") Cc: stable@vger.kernel.org Signed-off-by: Ian Kent <raven@themaw.net> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KMB only supports single resolution(1080p), this commit checks for
1920x1080x60 or 1920x1080x59 in crtc_mode_valid.
Also, modes with vfp < 4 are not supported in KMB display. This change
prunes display modes with vfp < 4.
v2: added vfp check
Fixes: 7f7b96a8a0a1 ("drm/kmb: Add support for KeemBay Display") Co-developed-by: Edmund Dea <edmund.j.dea@intel.com> Signed-off-by: Edmund Dea <edmund.j.dea@intel.com> Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com> Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link:https://patchwork.freedesktop.org/patch/msgid/20211013233632.471892-2-anitha.chrisanthus@intel.com Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both multipath and bonding events are changing the HW LAG state
independently.
Handling one of the features events while the other is already
enabled can cause unwanted behavior, for example handling
bonding event while multipath enabled will disable the lag and
cause multipath to stop working.
Fix it by ignoring bonding event while in multipath and ignoring FIB
events while in bonding mode.
Fixes: 544fe7c2e654 ("net/mlx5e: Activate HW multipath and handle port affinity based on FIB events") Signed-off-by: Maor Dickman <maord@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com> Reviewed-by: Mark Bloch <mbloch@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
If a netdev is removed from the lag the lag should be destroyed.
With downstream patches this might trigger a reconfiguration of
representors on a different eswitch and such we don't have the proper
locking to so from this path. Move the destruction to be done by the
workqueue.
As the destruction won't affect the netdev side it okay to do so.
The RDMA side will be reconfigured and it already coded to handle such
reconfiguration.
Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Mark Zhang <markzhang@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
rx unused desc is the desc that need attatching new buffer
before refilling to hw to receive new packet, the number of
desc need attatching new buffer is calculated using next_to_use
and next_to_clean. when next_to_use == next_to_clean, currently
hns3 driver assumes that all the desc has the buffer attatched,
but 'next_to_use == next_to_clean' also means all the desc need
attatching new buffer if hw has comsumed all the desc and the
driver has not attatched any buffer to the desc yet.
This patch adds 'refill' in desc_cb to indicate whether a new
buffer has been refilled to a desc.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit f1a0a376ca0c ("sched/core: Initialize the idle task with
preemption disabled") removed the init_idle() call from
idle_thread_get(). This was the sole call-path on hotplug that resets
the Shadow Call Stack (scs) Stack Pointer (sp).
Not resetting the scs-sp leads to scs overflow after enough hotplug
cycles. Therefore add an explicit scs_task_reset() to the hotplug code
to make sure the scs-sp does get reset on hotplug.
Fixes: f1a0a376ca0c ("sched/core: Initialize the idle task with preemption disabled") Signed-off-by: Woody Lin <woodylin@google.com>
[peterz: Changelog] Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Valentin Schneider <valentin.schneider@arm.com> Link: https://lore.kernel.org/r/20211012083521.973587-1-woodylin@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Decrease nr_thps counter in file's mapping to ensure that the page cache
won't be dropped excessively on file write access if page has been
already split.
I've tried a test scenario running a big binary, kernel remaps it with
THPs, then force a THP split with /sys/kernel/debug/split_huge_pages.
During any further open of that binary with O_RDWR or O_WRITEONLY kernel
drops page cache for it, because of non-zero thps counter.
Link: https://lkml.kernel.org/r/20211012120237.2600-1-m.szyprowski@samsung.com Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Fixes: 09d91cda0e82 ("mm,thp: avoid writes to file with THP in pagecache") Fixes: 06d3eff62d9d ("mm/thp: fix node page state in split_huge_page_to_list()") Acked-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reviewed-by: Yang Shi <shy828301@gmail.com> Cc: <sfoon.kim@samsung.com> Cc: Song Liu <songliubraving@fb.com> Cc: Rik van Riel <riel@surriel.com> Cc: "Kirill A . Shutemov" <kirill.shutemov@linux.intel.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: Hillf Danton <hdanton@sina.com> Cc: Hugh Dickins <hughd@google.com> Cc: William Kucharski <william.kucharski@oracle.com> Cc: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change the == to a != to avoid leaking the fcport structure or freeing
unallocated memory.
Link: https://lore.kernel.org/r/20211012191834.90306-2-jgu@purestorage.com Fixes: 8c0eb596baa5 ("[SCSI] qla2xxx: Fix a memory leak in an error path of qla2x00_process_els()") Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Joy Gu <jgu@purestorage.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The validation on the length of incoming packets performed in
storvsc_on_channel_callback() does not apply to unsolicited packets with ID
of 0 sent by Hyper-V. Adjust the validation for such unsolicited packets.
Link: https://lore.kernel.org/r/20211007122828.469289-1-parri.andrea@gmail.com Fixes: 91b1b640b834b2 ("scsi: storvsc: Validate length of incoming packet in storvsc_on_channel_callback()") Reported-by: Dexuan Cui <decui@microsoft.com> Reviewed-by: Michael Kelley <mikelley@microsoft.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 9e67600ed6b8 ("scsi: iscsi: Fix race condition between login and
sync thread") we meant to add a check where before we call ->set_param() we
make sure the iscsi_cls_connection is bound. The problem is that between
versions 4 and 5 of the patch the deletion of the unchecked set_param()
call was dropped so we ended up with 2 calls. As a result we can still hit
a crash where we access the unbound connection on the first call.
This patch removes that first call.
Fixes: 9e67600ed6b8 ("scsi: iscsi: Fix race condition between login and sync thread") Link: https://lore.kernel.org/r/20211010161904.60471-1-michael.christie@oracle.com Reviewed-by: Lee Duncan <lduncan@suse.com> Reviewed-by: Li Feng <fengli@smartx.com> Signed-off-by: Mike Christie <michael.christie@oracle.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On i.MX7S and i.MX8M* (but not i.MX6*) the pwrkey device has an
associated clock. Accessing the registers requires that this clock is
enabled. Binding the driver on at least i.MX7S and i.MX8MP while not
having the clock enabled results in a complete hang of the machine.
(This usually only happens if snvs_pwrkey is built as a module and the
rtc-snvs driver isn't already bound because at bootup the required clk
is on and only gets disabled when the clk framework disables unused clks
late during boot.)
This completes the fix in commit 135be16d3505 ("ARM: dts: imx7s: add
snvs clock to pwrkey").
The `cpu` argument of perf_evsel__read() must specify the cpu index.
perf_cpu_map__for_each_cpu() is for iterating the cpu number (not index)
and is thus not appropriate for use with perf_evsel__read().
So, if there is an offline CPU, the cpu number specified in the argument
may point out of range because the cpu number and the cpu index are
different.
io_mutex is taken by spi_setup() and spi-mux's .setup() callback calls
spi_setup() which results in a nested lock of io_mutex.
add_lock is taken by spi_add_device(). The device_add() call in there
can result in calling spi-mux's .probe() callback which registers its
own spi controller which in turn results in spi_add_device() being
called again.
To fix this initialize the controller's locks already in
spi_alloc_controller() to give spi_mux_probe() a chance to set the
lockdep subclass.
Currently we have a global spi_add_lock which we take when adding new
devices so that we can check that we're not trying to reuse a chip
select that's already controlled. This means that if the SPI device is
itself a SPI controller and triggers the instantiation of further SPI
devices we trigger a deadlock as we try to register and instantiate
those devices while in the process of doing so for the parent controller
and hence already holding the global spi_add_lock. Since we only care
about concurrency within a single SPI bus move the lock to be per
controller, avoiding the deadlock.
This can be easily triggered in the case of spi-mux.
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The snd_hdac_bus_reset_link() contains logic to clear STATESTS register
before performing controller reset. This code dates back to an old
bugfix in commit e8a7f136f5ed ("[ALSA] hda-intel - Improve HD-audio
codec probing robustness"). Originally the code was added to
azx_reset().
The code was moved around in commit a41d122449be ("ALSA: hda - Embed bus
into controller object") and ended up to snd_hdac_bus_reset_link() and
called primarily via snd_hdac_bus_init_chip().
The logic to clear STATESTS is correct when snd_hdac_bus_init_chip() is
called when controller is not in reset. In this case, STATESTS can be
cleared. This can be useful e.g. when forcing a controller reset to retry
codec probe. A normal non-power-on reset will not clear the bits.
However, this old logic is problematic when controller is already in
reset. The HDA specification states that controller must be taken out of
reset before writing to registers other than GCTL.CRST (1.0a spec,
3.3.7). The write to STATESTS in snd_hdac_bus_reset_link() will be lost
if the controller is already in reset per the HDA specification mentioned.
This has been harmless on older hardware. On newer generation of Intel
PCIe based HDA controllers, if configured to report issues, this write
will emit an unsupported request error. If ACPI Platform Error Interface
(APEI) is enabled in kernel, this will end up to kernel log.
Fix the code in snd_hdac_bus_reset_link() to only clear the STATESTS if
the function is called when controller is not in reset. Otherwise
clearing the bits is not possible and should be skipped.
The comment decribing the IPC timeout hadn't been updated when the
actual timeout was changed from 3 to 5 seconds in
commit a7d53dbbc70a ("platform/x86: intel_scu_ipc: Increase virtual
timeout from 3 to 5 seconds") .
Since the value is anyway updated to 10s now, take this opportunity to
update the value in the comment too.
Signed-off-by: Prashant Malani <pmalani@chromium.org> Cc: Benson Leung <bleung@chromium.org> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Link: https://lore.kernel.org/r/20210928101932.2543937-4-pmalani@chromium.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit a7d53dbbc70a ("platform/x86: intel_scu_ipc: Increase virtual
timeout from 3 to 5 seconds") states that the recommended timeout range
is 5-10 seconds. Adjust the timeout value to the higher of those i.e 10
seconds, to account for situations where the 5 seconds is insufficient
for disconnect command success.
Signed-off-by: Prashant Malani <pmalani@chromium.org> Cc: Benson Leung <bleung@chromium.org> Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com> Link: https://lore.kernel.org/r/20210928101932.2543937-3-pmalani@chromium.org Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
On SPEAr3xx, ethernet driver is not compatible with the SPEAr600
one.
Indeed, SPEAr3xx uses an earlier version of this IP (v3.40) and
needs some driver tuning compare to SPEAr600.
The v3.40 IP support was added to stmmac driver and this patch
fixes this issue and use the correct compatible string for
SPEAr3xx
Signed-off-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
dwmac 3.40a is an old ip version that can be found on SPEAr3xx soc.
Signed-off-by: Herve Codina <herve.codina@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently inode_in_dir() ignores errors returned from
btrfs_lookup_dir_index_item() and from btrfs_lookup_dir_item(), treating
any errors as if the directory entry does not exists in the fs/subvolume
tree, which is obviously not correct, as we can get errors such as -EIO
when reading extent buffers while searching the fs/subvolume's tree.
Fix that by making inode_in_dir() return the errors and making its only
caller, add_inode_ref(), deal with returned errors as well.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It seems that a few recent AMD systems show the codec configuration
errors at the early boot, while loading the driver at a later stage
works magically. Although the root cause of the error isn't clear,
it's certainly not bad to allow retrying the codec probe in such a
case if that helps.
This patch adds the capability for retrying the probe upon codec probe
errors on the certain AMD platforms. The probe_work is changed to a
delayed work, and at the secondary call, it'll jump to the codec
probing.
Note that, not only adding the re-probing, this includes the behavior
changes in the codec configuration function. Namely,
snd_hda_codec_configure() won't unregister the codec at errors any
longer. Instead, its caller, azx_codec_configure() unregisters the
codecs with the probe failures *if* any codec has been successfully
configured. If all codec probe failed, it doesn't unregister but let
it re-probed -- which is the most case we're seeing and this patch
tries to improve.
Even if the driver doesn't re-probe or give up, it will go to the
"free-all" error path, hence the leftover codecs shall be disabled /
deleted in anyway.
The libelf implementation from elftoolchain has a safety check in
gelf_update_rel[a] to check that the data corresponds to a section
that has type SHT_REL[A] [0]. If the relocation is updated before
the section header is updated with the proper type, this check
fails.
To fix this, update the section header first, before the relocations.
Previously, the section size was calculated in elf_rebuild_reloc_section
by counting the number of entries in the reloc_list. However, we
now need the size during elf_write so instead keep a running total
and add to it for every new relocation.
The structleak plugin causes the stack frame size to grow immensely:
lib/bitfield_kunit.c: In function 'test_bitfields_constants':
lib/bitfield_kunit.c:93:1: error: the frame size of 7440 bytes is larger than 2048 bytes [-Werror=frame-larger-than=]
The structleak plugin causes the stack frame size to grow immensely when
used with KUnit:
../drivers/base/test/property-entry-test.c:492:1: warning: the frame size of 2832 bytes is larger than 2048 bytes [-Wframe-larger-than=]
../drivers/base/test/property-entry-test.c:322:1: warning: the frame size of 2080 bytes is larger than 2048 bytes [-Wframe-larger-than=]
../drivers/base/test/property-entry-test.c:250:1: warning: the frame size of 4976 bytes is larger than 2048 bytes [-Wframe-larger-than=]
../drivers/base/test/property-entry-test.c:115:1: warning: the frame size of 3280 bytes is larger than 2048 bytes [-Wframe-larger-than=]
The structleak plugin causes the stack frame size to grow immensely when
used with KUnit:
../drivers/iio/test/iio-test-format.c: In function ‘iio_test_iio_format_value_fixedpoint’:
../drivers/iio/test/iio-test-format.c:98:1: warning: the frame size of 2336 bytes is larger than 2048 bytes [-Wframe-larger-than=]
I've seen some crashes in our crash reporting that *look* like multiple
threads stomping on each other while communicating with GMU. So wrap
all those paths in a lock.
Signed-off-by: Rob Clark <robdclark@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reference counting issue happens in the normal path of
kfree_at_end(). When kunit_alloc_and_get_resource() is invoked, the
function forgets to handle the returned resource object, whose refcount
increased inside, causing a refcount leak.
Fix this issue by calling kunit_alloc_resource() instead of
kunit_alloc_and_get_resource().
Fixed the following when applying:
Shuah Khan <skhan@linuxfoundation.org>
CHECK: Alignment should match open parenthesis
+ kunit_alloc_resource(test, NULL, kfree_res_free, GFP_KERNEL,
(void *)to_free);
Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Reviewed-by: Daniel Latypov <dlatypov@google.com> Reviewed-by: Brendan Higgins <brendanhiggins@google.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When updating mmu->pkru_mask, the value can only be added but it isn't
reset in advance. This will make mmu->pkru_mask keep the stale data.
Fix this issue.
Fixes: 2d344105f57c ("KVM, pkeys: introduce pkru_mask to cache conditions") Signed-off-by: Chenyi Qiang <chenyi.qiang@intel.com>
Message-Id: <20211021071022.1140-1-chenyi.qiang@intel.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the max tx size supported by the hw is calculated by
using the max BD num supported by the hw. According to the hw
user manual, the max tx size is fixed value for both non-TSO and
TSO skb.
This patch updates the max tx size according to the manual.
Fixes: 8ae10cfb5089("net: hns3: support tx-scatter-gather-fraglist feature") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mxsfb->crtc.funcs may already be NULL when unloading the driver,
in which case calling mxsfb_irq_disable() via drm_irq_uninstall() from
mxsfb_unload() leads to NULL pointer dereference.
Since all we care about is masking the IRQ and mxsfb->base is still
valid, just use that to clear and mask the IRQ.
Fixes: ae1ed00932819 ("drm: mxsfb: Stop using DRM simple display pipeline helper") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Abrecht <public@danielabrecht.ch> Cc: Emil Velikov <emil.l.velikov@gmail.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Sam Ravnborg <sam@ravnborg.org> Cc: Stefan Agner <stefan@agner.ch> Signed-off-by: Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20211016210446.171616-1-marex@denx.de Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The refactoring in commit bb18a6777465 ("KVM: SEV: Acquire
vcpu mutex when updating VMSA") left behind the assignment to
svm->vcpu.arch.guest_state_protected; add it back.
Signed-off-by: Peter Gonda <pgonda@google.com>
[Delta between v2 and v3 of Peter's patch, which had already been
committed; the commit message is my own. - Paolo] Fixes: bb18a6777465 ("KVM: SEV: Acquire vcpu mutex when updating VMSA") Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When I added IGMPv3 support I decided to follow the RFC for computing
the GMI dynamically:
" 8.4. Group Membership Interval
The Group Membership Interval is the amount of time that must pass
before a multicast router decides there are no more members of a
group or a particular source on a network.
This value MUST be ((the Robustness Variable) times (the Query
Interval)) plus (one Query Response Interval)."
But that actually is inconsistent with how the bridge used to compute it
for IGMPv2, where it was user-configurable that has a correct default value
but it is up to user-space to maintain it. This would make it consistent
with the other timer values which are also maintained correct by the user
instead of being dynamically computed. It also changes back to the previous
user-expected GMI behaviour for IGMPv3 queries which were supported before
IGMPv3 was added. Note that to properly compute it dynamically we would
need to add support for "Robustness Variable" which is currently missing.
Reported-by: Hangbin Liu <liuhangbin@gmail.com> Fixes: 0436862e417e ("net: bridge: mcast: support for IGMPv3/MLDv2 ALLOW_NEW_SOURCES report") Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During this process, the kernel thread would call detach_capi_ctr()
to detach a register controller. if the controller
was not attached yet, detach_capi_ctr() would
trigger an array-index-out-bounds bug.
[ 46.866069][ T6479] UBSAN: array-index-out-of-bounds in
drivers/isdn/capi/kcapi.c:483:21
[ 46.867196][ T6479] index -1 is out of range for type 'capi_ctr *[32]'
[ 46.867982][ T6479] CPU: 1 PID: 6479 Comm: kcmtpd_ctr_0 Not tainted
5.15.0-rc2+ #8
[ 46.869002][ T6479] Hardware name: QEMU Standard PC (i440FX + PIIX,
1996), BIOS 1.14.0-2 04/01/2014
[ 46.870107][ T6479] Call Trace:
[ 46.870473][ T6479] dump_stack_lvl+0x57/0x7d
[ 46.870974][ T6479] ubsan_epilogue+0x5/0x40
[ 46.871458][ T6479] __ubsan_handle_out_of_bounds.cold+0x43/0x48
[ 46.872135][ T6479] detach_capi_ctr+0x64/0xc0
[ 46.872639][ T6479] cmtp_session+0x5c8/0x5d0
[ 46.873131][ T6479] ? __init_waitqueue_head+0x60/0x60
[ 46.873712][ T6479] ? cmtp_add_msgpart+0x120/0x120
[ 46.874256][ T6479] kthread+0x147/0x170
[ 46.874709][ T6479] ? set_kthread_struct+0x40/0x40
[ 46.875248][ T6479] ret_from_fork+0x1f/0x30
[ 46.875773][ T6479]
The nci_core_conn_close_rsp_packet() function will release the conn_info
with given conn_id. However, it needs to set the rf_conn_info to NULL to
prevent other routines like nci_rf_intf_activated_ntf_packet() to trigger
the UAF.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Lin Ma <linma@zju.edu.cn> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
complete_emulator_pio_in can expect that vcpu->arch.pio has been filled in,
and therefore does not need the size and count arguments. This makes things
nicer when the function is called directly from a complete_userspace_io
callback.
No functional change intended.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
emulator_pio_in handles both the case where the data is pending in
vcpu->arch.pio.count, and the case where I/O has to be done via either
an in-kernel device or a userspace exit. For SEV-ES we would like
to split these, to identify clearly the moment at which the
sev_pio_data is consumed. To this end, create two different
functions: __emulator_pio_in fills in vcpu->arch.pio.count, while
complete_emulator_pio_in clears it and releases vcpu->arch.pio.data.
Because this patch has to be backported, things are left a bit messy.
kernel_pio() operates on vcpu->arch.pio, which leads to emulator_pio_in()
having with two calls to complete_emulator_pio_in(). It will be fixed
in the next release.
While at it, remove the unused void* val argument of emulator_pio_in_out.
The function currently hardcodes vcpu->arch.pio_data as the
source/destination buffer, which sucks but will be fixed after the more
severe SEV-ES buffer overflow.
No functional change intended.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kvm_x86_sync_pir_to_irr callback can sometimes set KVM_REQ_EVENT.
If that happens exactly at the time that an exit is handled as
EXIT_FASTPATH_REENTER_GUEST, vcpu_enter_guest will go incorrectly
through the loop that calls kvm_x86_run, instead of processing
the request promptly.
Fixes: 379a3c8ee444 ("KVM: VMX: Optimize posted-interrupt delivery for timer fastpath") Cc: stable@vger.kernel.org Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently emulator_pio_in clears vcpu->arch.pio.count twice if
emulator_pio_in_out performs kernel PIO. Move the clear into
emulator_pio_out where it is actually necessary.
No functional change intended.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size of the GHCB scratch area is limited to 16 KiB (GHCB_SCRATCH_AREA_LIMIT),
so there is no need for it to be a u64. This fixes a build error on 32-bit
systems:
i686-linux-gnu-ld: arch/x86/kvm/svm/sev.o: in function `sev_es_string_io:
sev.c:(.text+0x110f): undefined reference to `__udivdi3'
The PIO scratch buffer is larger than a single page, and therefore
it is not possible to copy it in a single step to vcpu->arch/pio_data.
Bound each call to emulator_pio_in/out to a single page; keep
track of how many I/O operations are left in vcpu->arch.sev_pio_count,
so that the operation can be restarted in the complete_userspace_io
callback.
For OUT, this means that the previous kvm_sev_es_outs implementation
becomes an iterator of the loop, and we can consume the sev_pio_data
buffer before leaving to userspace.
For IN, instead, consuming the buffer and decreasing sev_pio_count
is always done in the complete_userspace_io callback, because that
is when the memcpy is done into sev_pio_data.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Reported-by: Felix Wilhelm <fwilhelm@google.com> Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The size of the data in the scratch buffer is not divided by the size of
each port I/O operation, so vcpu->arch.pio.count ends up being larger
than it should be by a factor of size.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Acked-by: Tom Lendacky <thomas.lendacky@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few very small cleanups to the functions, smushed together because
the patch is already very small like this:
- inline emulator_pio_in_emulated and emulator_pio_out_emulated,
since we already have the vCPU
- remove the data argument and pull setting vcpu->arch.sev_pio_data into
the caller
- remove unnecessary clearing of vcpu->arch.pio.count when
emulation is done by the kernel (and therefore vcpu->arch.pio.count
is already clear on exit from emulator_pio_in and emulator_pio_out).
No functional change intended.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will be using this field for OUTS emulation as well, in case the
data that is pushed via OUTS spans more than one page. In that case,
there will be a need to save the data pointer across exits to userspace.
So, change the name to something that refers to any kind of PIO.
Also spell out what it is used for, namely SEV-ES.
No functional change intended.
Cc: stable@vger.kernel.org Fixes: 7ed9abfe8e9f ("KVM: SVM: Support string IO operations for an SEV-ES guest") Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flush the destination page before invoking RECEIVE_UPDATE_DATA, as the
PSP encrypts the data with the guest's key when writing to guest memory.
If the target memory was not previously encrypted, the cache may contain
dirty, unecrypted data that will persist on non-coherent systems.
Fixes: 15fb7de1a7f5 ("KVM: SVM: Add KVM_SEV_RECEIVE_UPDATE_DATA command") Cc: stable@vger.kernel.org Cc: Peter Gonda <pgonda@google.com> Cc: Marc Orr <marcorr@google.com> Cc: Tom Lendacky <thomas.lendacky@amd.com> Cc: Brijesh Singh <brijesh.singh@amd.com> Signed-off-by: Masahiro Kozuka <masa.koz@kozuka.jp>
[sean: converted bug report to changelog] Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210914210951.2994260-3-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit c300ab9f08df ("KVM: x86: Replace late check_nested_events() hack with
more precise fix") there is no longer the certainty that check_nested_events()
tries to inject an external interrupt vmexit to L1 on every call to vcpu_enter_guest.
Therefore, even in that case we need to set KVM_REQ_EVENT. This ensures
that inject_pending_event() is called, and from there kvm_check_nested_events().
Fixes: c300ab9f08df ("KVM: x86: Replace late check_nested_events() hack with more precise fix") Cc: stable@vger.kernel.org Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmem_cache_free_bulk() will call memcg_slab_free_hook() for all objects
when doing bulk free. So we shouldn't call memcg_slab_free_hook() again
for bulk free to avoid incorrect memcg slab count.
Link: https://lkml.kernel.org/r/20210916123920.48704-6-linmiaohe@huawei.com Fixes: d1b2cf6cb84a ("mm: memcg/slab: uncharge during kmem_cache_free_bulk()") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Bharata B Rao <bharata@linux.ibm.com> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Faiyaz Mohammed <faiyazm@codeaurora.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Pekka Enberg <penberg@kernel.org> Cc: Roman Gushchin <guro@fb.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When sysfs_slab_add failed, we shouldn't call debugfs_slab_add() for s
because s will be freed soon. And slab_debugfs_fops will use s later
leading to a use-after-free.
Link: https://lkml.kernel.org/r/20210916123920.48704-5-linmiaohe@huawei.com Fixes: 64dd68497be7 ("mm: slub: move sysfs slab alloc/free interfaces to debugfs") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Bharata B Rao <bharata@linux.ibm.com> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Faiyaz Mohammed <faiyazm@codeaurora.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Pekka Enberg <penberg@kernel.org> Cc: Roman Gushchin <guro@fb.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If object's reuse is delayed, it will be excluded from the reconstructed
freelist. But we forgot to adjust the cnt accordingly. So there will
be a mismatch between reconstructed freelist depth and cnt. This will
lead to free_debug_processing() complaining about freelist count or a
incorrect slub inuse count.
Link: https://lkml.kernel.org/r/20210916123920.48704-3-linmiaohe@huawei.com Fixes: c3895391df38 ("kasan, slub: fix handling of kasan_slab_free hook") Signed-off-by: Miaohe Lin <linmiaohe@huawei.com> Reviewed-by: Vlastimil Babka <vbabka@suse.cz> Cc: Andrey Konovalov <andreyknvl@gmail.com> Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com> Cc: Bharata B Rao <bharata@linux.ibm.com> Cc: Christoph Lameter <cl@linux.com> Cc: David Rientjes <rientjes@google.com> Cc: Faiyaz Mohammed <faiyazm@codeaurora.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Kees Cook <keescook@chromium.org> Cc: Pekka Enberg <penberg@kernel.org> Cc: Roman Gushchin <guro@fb.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In isa206_idle_insn_mayloss() we store various registers into the stack
red zone, which is allowed.
However inside the IDLE_STATE_ENTER_SEQ_NORET macro we save r2 again,
to 0(r1), which corrupts the stack back chain.
We used to do the same in isa206_idle_insn_mayloss() itself, but we
fixed that in 73287caa9210 ("powerpc64/idle: Fix SP offsets when saving
GPRs"), however we missed that the macro also corrupts the back chain.
Corrupting the back chain is bad for debuggability but doesn't
necessarily cause a bug.
However we recently changed the stack handling in some KVM code, and it
now relies on the stack back chain being valid when it returns. The
corruption causes that code to return with r1 pointing somewhere in
kernel data, at some point LR is restored from the stack and we branch
to NULL or somewhere else invalid.
Only affects Power8 hosts running KVM guests, with dynamic_mt_modes
enabled (which it is by default).
The fixes tag below points to the commit that changed the KVM stack
handling, exposing this bug. The actual corruption of the back chain has
always existed since 948cf67c4726 ("powerpc: Add NAP mode support on
Power7 in HV mode").
We call idle_kvm_start_guest() from power7_offline() if the thread has
been requested to enter KVM. We pass it the SRR1 value that was returned
from power7_idle_insn() which tells us what sort of wakeup we're
processing.
Depending on the SRR1 value we pass in, the KVM code might enter the
guest, or it might return to us to do some host action if the wakeup
requires it.
If idle_kvm_start_guest() is able to handle the wakeup, and enter the
guest it is supposed to indicate that by returning a zero SRR1 value to
us.
That was the behaviour prior to commit 10d91611f426 ("powerpc/64s:
Reimplement book3s idle code in C"), however in that commit the
handling of SRR1 was reworked, and the zeroing behaviour was lost.
Returning from idle_kvm_start_guest() without zeroing the SRR1 value can
confuse the host offline code, causing the guest to crash and other
weirdness.
In commit 10d91611f426 ("powerpc/64s: Reimplement book3s idle code in
C") kvm_start_guest() became idle_kvm_start_guest(). The old code
allocated a stack frame on the emergency stack, but didn't use the
frame to store anything, and also didn't store anything in its caller's
frame.
idle_kvm_start_guest() on the other hand is written more like a normal C
function, it creates a frame on entry, and also stores CR/LR into its
callers frame (per the ABI). The problem is that there is no caller
frame on the emergency stack.
The emergency stack for a given CPU is allocated with:
So emergency_sp actually points to the first address above the emergency
stack allocation for a given CPU, we must not store above it without
first decrementing it to create a frame. This is different to the
regular kernel stack, paca->kstack, which is initialised to point at an
initial frame that is ready to use.
idle_kvm_start_guest() stores the backchain, CR and LR all of which
write outside the allocation for the emergency stack. It then creates a
stack frame and saves the non-volatile registers. Unfortunately the
frame it creates is not large enough to fit the non-volatiles, and so
the saving of the non-volatile registers also writes outside the
emergency stack allocation.
The end result is that we corrupt whatever is at 0-24 bytes, and 112-248
bytes above the emergency stack allocation.
In practice this has gone unnoticed because the memory immediately above
the emergency stack happens to be used for other stack allocations,
either another CPUs mc_emergency_sp or an IRQ stack. See the order of
calls to irqstack_early_init() and emergency_stack_init().
The low addresses of another stack are the top of that stack, and so are
only used if that stack is under extreme pressue, which essentially
never happens in practice - and if it did there's a high likelyhood we'd
crash due to that stack overflowing.
Still, we shouldn't be corrupting someone else's stack, and it is purely
luck that we aren't corrupting something else.
To fix it we save CR/LR into the caller's frame using the existing r1 on
entry, we then create a SWITCH_FRAME_SIZE frame (which has space for
pt_regs) on the emergency stack with the backchain pointing to the
existing stack, and then finally we switch to the new frame on the
emergency stack.
In commit fda31c50292a ("signal: avoid double atomic counter
increments for user accounting") Linus made a clever optimization to
how rlimits and the struct user_struct. Unfortunately that
optimization does not work in the obvious way when moved to nested
rlimits. The problem is that the last decrement of the per user
namespace per user sigpending counter might also be the last decrement
of the sigpending counter in the parent user namespace as well. Which
means that simply freeing the leaf ucount in __free_sigqueue is not
enough.
Maintain the optimization and handle the tricky cases by introducing
inc_rlimit_get_ucounts and dec_rlimit_put_ucounts.
By moving the entire optimization into functions that perform all of
the work it becomes possible to ensure that every level is handled
properly.
The new function inc_rlimit_get_ucounts returns 0 on failure to
increment the ucount. This is different than inc_rlimit_ucounts which
increments the ucounts and returns LONG_MAX if the ucount counter has
exceeded it's maximum or it wrapped (to indicate the counter needs to
decremented).
I wish we had a single user to account all pending signals to across
all of the threads of a process so this complexity was not necessary
Cc: stable@vger.kernel.org Fixes: d64696905554 ("Reimplement RLIMIT_SIGPENDING on top of ucounts")
v1: https://lkml.kernel.org/r/87mtnavszx.fsf_-_@disp2133 Link: https://lkml.kernel.org/r/87fssytizw.fsf_-_@disp2133 Reviewed-by: Alexey Gladkov <legion@kernel.org> Tested-by: Rune Kleveland <rune.kleveland@infomedia.dk> Tested-by: Yu Zhao <yuzhao@google.com> Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of leaking the ucounts in new if alloc_ucounts fails, store
the result of alloc_ucounts into a temporary variable, which is later
assigned to new->ucounts.
Cc: stable@vger.kernel.org Fixes: 905ae01c4ae2 ("Add a reference to ucounts for each cred") Link: https://lkml.kernel.org/r/87pms2s0v8.fsf_-_@disp2133 Tested-by: Yu Zhao <yuzhao@google.com> Reviewed-by: Alexey Gladkov <legion@kernel.org> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The purpose of inc_rlimit_ucounts and dec_rlimit_ucounts in commit_creds
is to change which rlimit counter is used to track a process when the
credentials changes.
Use the same test for both to guarantee the tracking is correct.
Cc: stable@vger.kernel.org Fixes: 21d1c5e386bc ("Reimplement RLIMIT_NPROC on top of ucounts") Link: https://lkml.kernel.org/r/87v91us0w4.fsf_-_@disp2133 Tested-by: Yu Zhao <yuzhao@google.com> Reviewed-by: Alexey Gladkov <legion@kernel.org> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting cred->ucounts in cred_alloc_blank does not make sense. The
uid and user_ns are deliberately not set in cred_alloc_blank but
instead the setting is delayed until key_change_session_keyring.
So move dealing with ucounts into key_change_session_keyring as well.
Unfortunately that movement of get_ucounts adds a new failure mode to
key_change_session_keyring. I do not see anything stopping the parent
process from calling setuid and changing the relevant part of it's
cred while keyctl_session_to_parent is running making it fundamentally
necessary to call get_ucounts in key_change_session_keyring. Which
means that the new failure mode cannot be avoided.
A failure of key_change_session_keyring results in a single threaded
parent keeping it's existing credentials. Which results in the parent
process not being able to access the session keyring and whichever
keys are in the new keyring.
Further get_ucounts is only expected to fail if the number of bits in
the refernece count for the structure is too few.
Since the code has no other way to report the failure of get_ucounts
and because such failures are not expected to be common add a WARN_ONCE
to report this problem to userspace.
Between the WARN_ONCE and the parent process not having access to
the keys in the new session keyring I expect any failure of get_ucounts
will be noticed and reported and we can find another way to handle this
condition. (Possibly by just making ucounts->count an atomic_long_t).
Cc: stable@vger.kernel.org Fixes: 905ae01c4ae2 ("Add a reference to ucounts for each cred") Link: https://lkml.kernel.org/r/7k0ias0uf.fsf_-_@disp2133 Tested-by: Yu Zhao <yuzhao@google.com> Reviewed-by: Alexey Gladkov <legion@kernel.org> Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary
dsa_port's and call mt7530_port_disable for non-existent ports.
Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in
port_enable/disable is no longer required.
Cc: stable@vger.kernel.org Signed-off-by: DENG Qingfang <dqfext@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
c3df5fb57fe8 ("cgroup: rstat: fix A-A deadlock on 32bit around
u64_stats_sync") made u64_stats updates irq-safe to avoid A-A deadlocks.
Unfortunately, the conversion missed one in blk_cgroup_bio_start(). Fix it.
Commit 1d25684e2251 ("ASoC: nau8824: Fix open coded prefix handling")
replaced the nau8824_dapm_enable_pin() helper with direct calls to
snd_soc_dapm_enable_pin(), but the helper was using
snd_soc_dapm_force_enable_pin() and not forcing the MICBIAS + SAR
supplies on breaks headphone vs headset and button-press detection.
Replace the snd_soc_dapm_enable_pin() calls with
snd_soc_dapm_force_enable_pin() to fix this.
Cc: stable@vger.kernel.org Fixes: 1d25684e2251 ("ASoC: nau8824: Fix open coded prefix handling") Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20210929201512.460360-1-hdegoede@redhat.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The put callback of a kcontrol is supposed to return 1 when the value
is changed, and this will be notified to user-space. However, some
DAPM kcontrols always return 0 (except for errors), hence the
user-space misses the update of a control value.
This patch corrects the behavior by properly returning 1 when the
value gets updated.
Reported-and-tested-by: Hans de Goede <hdegoede@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/20211006141712.2439-1-tiwai@suse.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per discussion at: https://github.com/szszoke/sennheiser-gsp670-pulseaudio-profile/issues/13
The GSP670 has 2 playback and 1 recording device that by default are
detected in an incompatible order for alsa. This may have been done to make
it compatible for the console by the manufacturer and only affects the
latest firmware which uses its own ID.
This quirk will resolve this by reordering the channels.
Check for a NULL page->mapping before dereferencing the mapping in
page_is_secretmem(), as the page's mapping can be nullified while gup()
is running, e.g. by reclaim or truncation.
Link: https://lkml.kernel.org/r/20211007231502.3552715-1-seanjc@google.com Fixes: 1507f51255c9 ("mm: introduce memfd_secret system call to create "secret" memory areas") Signed-off-by: Sean Christopherson <seanjc@google.com> Reported-by: Darrick J. Wong <djwong@kernel.org> Reported-by: Stephen <stephenackerman16@gmail.com> Tested-by: Darrick J. Wong <djwong@kernel.org> Reviewed-by: David Hildenbrand <david@redhat.com> Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we open a file without read access and then pass the fd to a syscall
whose implementation calls kernel_read_file_from_fd(), we get a warning
from __kernel_read():
if (WARN_ON_ONCE(!(file->f_mode & FMODE_READ)))
This currently affects both finit_module() and kexec_file_load(), but it
could affect other syscalls in the future.
Link: https://lkml.kernel.org/r/20211007220110.600005-1-willy@infradead.org Fixes: b844f0ecbc56 ("vfs: define kernel_copy_file_from_fd()") Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org> Reported-by: Hao Sun <sunhao.th@gmail.com> Reviewed-by: Kees Cook <keescook@chromium.org> Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Mimi Zohar <zohar@linux.ibm.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6e7b64b9dd6d ("elfcore: fix building with clang") introduces
special handling for two architectures, ia64 and User Mode Linux.
However, the wrong name, i.e., CONFIG_UM, for the intended Kconfig
symbol for User-Mode Linux was used.
Although the directory for User Mode Linux is ./arch/um; the Kconfig
symbol for this architecture is called CONFIG_UML.
Luckily, ./scripts/checkkconfigsymbols.py warns on non-existing configs:
UM
Referencing files: include/linux/elfcore.h
Similar symbols: UML, NUMA
Correct the name of the config to the intended one.
syzbot reported access to unitialized memory in mbind() [1]
Issue came with commit bda420b98505 ("numa balancing: migrate on fault
among multiple bound nodes")
This commit added a new bit in MPOL_MODE_FLAGS, but only checked valid
combination (MPOL_F_NUMA_BALANCING can only be used with MPOL_BIND) in
do_set_mempolicy()
This patch moves the check in sanitize_mpol_flags() so that it is also
used by mbind()
A race is possible when a process exits, its VMAs are removed by
exit_mmap() and at the same time userfaultfd_writeprotect() is called.
The race was detected by KASAN on a development kernel, but it appears
to be possible on vanilla kernels as well.
Use mmget_not_zero() to prevent the race as done in other userfaultfd
operations.
Link: https://lkml.kernel.org/r/20210921200247.25749-1-namit@vmware.com Fixes: 63b2d4174c4ad ("userfaultfd: wp: add the writeprotect API to userfaultfd ioctl") Signed-off-by: Nadav Amit <namit@vmware.com> Tested-by: Li Wang <liwang@redhat.com> Reviewed-by: Peter Xu <peterx@redhat.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It can be easily reproduced when global thp enabled, which is the
default for RHEL.
It's also known as a side effect of commit 0db282ba2c12 ("selftest: use
mmap instead of posix_memalign to allocate memory", 2021-07-23), which
is imho right itself on using mmap() to make sure the addresses will be
untagged even on arm.
The problem is, for each test we allocate buffers using two
allocate_area() calls. We assumed these two buffers won't affect each
other, however they could, because mmap() could have found that the two
buffers are near each other and having the same VMA flags, so they got
merged into one VMA.
It won't be a big problem if thp is not enabled, but when thp is
agressively enabled it means when initializing the src buffer it could
accidentally setup part of the dest buffer too when there's a shared THP
that overlaps the two regions. Then some of the dest buffer won't be
able to be trapped by userfaultfd missing mode, then it'll cause memory
corruption as described.
To fix it, do release_pages() after initializing the src buffer.
Since the previous two release_pages() calls are after
uffd_test_ctx_clear() which will unmap all the buffers anyway (which is
stronger than release pages; as unmap() also tear town pgtables), drop
them as they shouldn't really be anything useful.
We can mark the Fixes tag upon 0db282ba2c12 as it's reported to only
happen there, however the real "Fixes" IMHO should be 8ba6e8640844, as
before that commit we'll always do explicit release_pages() before
registration of uffd, and 8ba6e8640844 changed that logic by adding
extra unmap/map and we didn't release the pages at the right place.
Meanwhile I don't have a solid glue anyway on whether posix_memalign()
could always avoid triggering this bug, hence it's safer to attach this
fix to commit 8ba6e8640844.
Link: https://lkml.kernel.org/r/20210923232512.210092-1-peterx@redhat.com Fixes: 8ba6e8640844 ("userfaultfd/selftests: reinitialize test context in each test")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1994931 Signed-off-by: Peter Xu <peterx@redhat.com> Reported-by: Li Wang <liwan@redhat.com> Tested-by: Li Wang <liwang@redhat.com> Reviewed-by: Axel Rasmussen <axelrasmussen@google.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Nadav Amit <nadav.amit@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with kernel 5.11 built with CONFIG_FORTIFY_SOURCE mouting an
ocfs2 filesystem with either o2cb or pcmk cluster stack fails with the
trace below. Problem seems to be that strings for cluster stack and
cluster name are not guaranteed to be null terminated in the disk
representation, while strlcpy assumes that the source string is always
null terminated. This causes a read outside of the source string
triggering the buffer overflow detection.
Commit 6dbf7bb55598 ("fs: Don't invalidate page buffers in
block_write_full_page()") uncovered a latent bug in ocfs2 conversion
from inline inode format to a normal inode format.
The code in ocfs2_convert_inline_data_to_extents() attempts to zero out
the whole cluster allocated for file data by grabbing, zeroing, and
dirtying all pages covering this cluster. However these pages are
beyond i_size, thus writeback code generally ignores these dirty pages
and no blocks were ever actually zeroed on the disk.
This oversight was fixed by commit 693c241a5f6a ("ocfs2: No need to zero
pages past i_size.") for standard ocfs2 write path, inline conversion
path was apparently forgotten; the commit log also has a reasoning why
the zeroing actually is not needed.
After commit 6dbf7bb55598, things became worse as writeback code stopped
invalidating buffers on pages beyond i_size and thus these pages end up
with clean PageDirty bit but with buffers attached to these pages being
still dirty. So when a file is converted from inline format, then
writeback triggers, and then the file is grown so that these pages
become valid, the invalid dirtiness state is preserved,
mark_buffer_dirty() does nothing on these pages (buffers are already
dirty) but page is never written back because it is clean. So data
written to these pages is lost once pages are reclaimed.
After unmounting and mounting the fs again, you can observe that end of
'ocfs2_file' has lost its contents.
Fix the problem by not doing the pointless zeroing during conversion
from inline format similarly as in the standard write path.
[akpm@linux-foundation.org: fix whitespace, per Joseph]
Link: https://lkml.kernel.org/r/20210930095405.21433-1-jack@suse.cz Fixes: 6dbf7bb55598 ("fs: Don't invalidate page buffers in block_write_full_page()") Signed-off-by: Jan Kara <jack@suse.cz> Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com> Tested-by: Joseph Qi <joseph.qi@linux.alibaba.com> Acked-by: Gang He <ghe@suse.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Jun Piao <piaojun@huawei.com> Cc: "Markov, Andrey" <Markov.Andrey@Dell.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While writing an email explaining the "bit = 0" logic for a discussion on
making ftrace_test_recursion_trylock() disable preemption, I discovered a
path that makes the "not do the logic if bit is zero" unsafe.
The recursion logic is done in hot paths like the function tracer. Thus,
any code executed causes noticeable overhead. Thus, tricks are done to try
to limit the amount of code executed. This included the recursion testing
logic.
Having recursion testing is important, as there are many paths that can
end up in an infinite recursion cycle when tracing every function in the
kernel. Thus protection is needed to prevent that from happening.
Because it is OK to recurse due to different running context levels (e.g.
an interrupt preempts a trace, and then a trace occurs in the interrupt
handler), a set of bits are used to know which context one is in (normal,
softirq, irq and NMI). If a recursion occurs in the same level, it is
prevented*.
Then there are infrastructure levels of recursion as well. When more than
one callback is attached to the same function to trace, it calls a loop
function to iterate over all the callbacks. Both the callbacks and the
loop function have recursion protection. The callbacks use the
"ftrace_test_recursion_trylock()" which has a "function" set of context
bits to test, and the loop function calls the internal
trace_test_and_set_recursion() directly, with an "internal" set of bits.
If an architecture does not implement all the features supported by ftrace
then the callbacks are never called directly, and the loop function is
called instead, which will implement the features of ftrace.
Since both the loop function and the callbacks do recursion protection, it
was seemed unnecessary to do it in both locations. Thus, a trick was made
to have the internal set of recursion bits at a more significant bit
location than the function bits. Then, if any of the higher bits were set,
the logic of the function bits could be skipped, as any new recursion
would first have to go through the loop function.
This is true for architectures that do not support all the ftrace
features, because all functions being traced must first go through the
loop function before going to the callbacks. But this is not true for
architectures that support all the ftrace features. That's because the
loop function could be called due to two callbacks attached to the same
function, but then a recursion function inside the callback could be
called that does not share any other callback, and it will be called
directly.
i.e.
traced_function_1: [ more than one callback tracing it ]
call loop_func
loop_func:
trace_recursion set internal bit
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
traced_function_2: [ only traced by above callback ]
call callback
callback:
trace_recursion [ skipped because internal bit is set, return 0 ]
call traced_function_2
[ wash, rinse, repeat, BOOM! out of shampoo! ]
Thus, the "bit == 0 skip" trick is not safe, unless the loop function is
call for all functions.
Since we want to encourage architectures to implement all ftrace features,
having them slow down due to this extra logic may encourage the
maintainers to update to the latest ftrace features. And because this
logic is only safe for them, remove it completely.
[*] There is on layer of recursion that is allowed, and that is to allow
for the transition between interrupt context (normal -> softirq ->
irq -> NMI), because a trace may occur before the context update is
visible to the trace recursion logic.
Link: https://lore.kernel.org/all/609b565a-ed6e-a1da-f025-166691b5d994@linux.alibaba.com/ Link: https://lkml.kernel.org/r/20211018154412.09fcad3c@gandalf.local.home Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: "James E.J. Bottomley" <James.Bottomley@hansenpartnership.com> Cc: Helge Deller <deller@gmx.de> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Paul Walmsley <paul.walmsley@sifive.com> Cc: Palmer Dabbelt <palmer@dabbelt.com> Cc: Albert Ou <aou@eecs.berkeley.edu> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Borislav Petkov <bp@alien8.de> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Jiri Kosina <jikos@kernel.org> Cc: Miroslav Benes <mbenes@suse.cz> Cc: Joe Lawrence <joe.lawrence@redhat.com> Cc: Colin Ian King <colin.king@canonical.com> Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org> Cc: Nicholas Piggin <npiggin@gmail.com> Cc: Jisheng Zhang <jszhang@kernel.org> Cc: =?utf-8?b?546L6LSH?= <yun.wang@linux.alibaba.com> Cc: Guo Ren <guoren@kernel.org> Cc: stable@vger.kernel.org Fixes: edc15cafcbfa3 ("tracing: Avoid unnecessary multiple recursion checks") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, we check the wb_err too early for directories, before all of
the unsafe child requests have been waited on. In order to fix that we
need to check the mapping->wb_err later nearer to the end of ceph_fsync.
We also have an overly-complex method for tracking errors after
blocklisting. The errors recorded in cleanup_session_requests go to a
completely separate field in the inode, but we end up reporting them the
same way we would for any other error (in fsync).
There's no real benefit to tracking these errors in two different
places, since the only reporting mechanism for them is in fsync, and
we'd need to advance them both every time.
Given that, we can just remove i_meta_err, and convert the places that
used it to instead just use mapping->wb_err instead. That also fixes
the original problem by ensuring that we do a check_and_advance of the
wb_err at the end of the fsync op.
Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/52864 Reported-by: Patrick Donnelly <pdonnell@redhat.com> Signed-off-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently when mounting, we may end up finding an existing superblock
that corresponds to a blocklisted MDS client. This means that the new
mount ends up being unusable.
If we've found an existing superblock with a client that is already
blocklisted, and the client is not configured to recover on its own,
fail the match. Ditto if the superblock has been forcibly unmounted.
While we're in here, also rename "other" to the more conventional "fsc".
The receiver should abort TP if 'total message size' in TP.CM_RTS and
TP.CM_BAM is less than 9 or greater than 1785 [1], but currently the
j1939 stack only checks the upper bound and the receiver will accept
the following broadcast message:
When the session state is J1939_SESSION_DONE, j1939_tp_rxtimer() will
give an alert "rx timeout, send abort", but do nothing actually. Move
the alert into session active judgment condition, it is more
reasonable.
One of the scenarios is that j1939_tp_rxtimer() execute followed by
j1939_xtp_rx_abort_one(). After j1939_xtp_rx_abort_one(), the session
state is J1939_SESSION_DONE, then j1939_tp_rxtimer() give an alert.
Fixes: 9d71dd0c7009 ("can: add support of SAE J1939 protocol") Link: https://lore.kernel.org/all/20210906094219.95924-1-william.xuanziyang@huawei.com Cc: stable@vger.kernel.org Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com> Acked-by: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When isotp_sendmsg() concurrent, tx.state of all TX processes can be
ISOTP_IDLE. The conditions so->tx.state != ISOTP_IDLE and
wq_has_sleeper(&so->wait) can not protect TX buffer from being
accessed by multiple TX processes.
We can use cmpxchg() to try to modify tx.state to ISOTP_SENDING firstly.
If the modification of the previous process succeed, the later process
must wait tx.state to ISOTP_IDLE firstly. Thus, we can ensure TX buffer
is accessed by only one process at the same time. And we should also
restore the original tx.state at the subsequent error processes.
projects / linux-stable / log