In case a guest isn't consuming incoming network traffic as fast as it
is coming in, xen-netback is buffering network packages in unlimited
numbers today. This can result in host OOM situations.
Commit f48da8b14d04ca8 ("xen-netback: fix unlimited guest Rx internal
queue and carrier flapping") meant to introduce a mechanism to limit
the amount of buffered data by stopping the Tx queue when reaching the
data limit, but this doesn't work for cases like UDP.
When hitting the limit don't queue further SKBs, but drop them instead.
In order to be able to tell Rx packages have been dropped increment the
rx_dropped statistics counter in this case.
It should be noted that the old solution to continue queueing SKBs had
the additional problem of an overflow of the 32-bit rx_queue_len value
would result in intermittent Tx queue enabling.
Commit 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when
not using GSO") introduced a security problem in netback, as an
interface would only be regarded to be stalled if no slot is available
in the rx queue ring page. In case the SKB at the head of the queued
requests will need more than one rx slot and only one slot is free the
stall detection logic will never trigger, as the test for that is only
looking for at least one slot to be free.
Fix that by testing for the needed number of slots instead of only one
slot being available.
In order to not have to take the rx queue lock that often, store the
number of needed slots in the queue data. As all SKB dequeue operations
happen in the rx queue kernel thread this is safe, as long as the
number of needed slots is accessed via READ/WRITE_ONCE() only and
updates are always done with the rx queue lock held.
Add a small helper for obtaining the number of free slots.
This is part of XSA-392
Fixes: 1d5d48523900a4b ("xen-netback: require fewer guest Rx slots when not using GSO") Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Xen console driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using a lateeoi event
channel.
For the normal domU initial console this requires the introduction of
bind_evtchn_to_irq_lateeoi() as there is no xenbus device available
at the time the event channel is bound to the irq.
As the decision whether an interrupt was spurious or not requires to
test for bytes having been read from the backend, move sending the
event into the if statement, as sending an event without having found
any bytes to be read is making no sense at all.
The Xen netfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
For being able to detect the case of no rx responses being added while
the carrier is down a new lock is needed in order to update and test
rsp_cons and the number of seen unconsumed responses atomically.
The Xen blkfront driver is still vulnerable for an attack via excessive
number of events sent by the backend. Fix that by using lateeoi event
channels.
This patch causes a Tx only workload to go to sleep even when it does
not have to, leading to misserable performance in skb mode. It fixed
one rare problem but created a much worse one, so this need to be
reverted while I try to craft a proper solution to the original
problem.
Fixes: bd0687c18e63 ("xsk: Do not sleep in poll() when need_wakeup set") Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20211217145646.26449-1-magnus.karlsson@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DAMON debugfs interface users were able to trigger warning by writing
some files with arbitrarily large 'count' parameter. The issue is fixed
with commit db7a347b26fe ("mm/damon/dbgfs: use '__GFP_NOWARN' for
user-specified size buffer allocation"). This commit adds a test case
for the issue in DAMON selftests to avoid future regressions.
Fix drivers/bus/ti-sysc.c:2494:13: error: variable 'error' set but not
used introduced by commit 9d881361206e ("bus: ti-sysc: Add quirk handling
for reinit on context lost").
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The latter invokes worker creation with the wqe->lock held, but that can
run into problems if we end up exiting and need to cancel the queued work.
syzbot caught this:
============================================
WARNING: possible recursive locking detected
5.16.0-rc4-syzkaller #0 Not tainted
--------------------------------------------
iou-wrk-6468/6471 is trying to acquire lock: ffff88801aa98018 (&wqe->lock){+.+.}-{2:2}, at: io_worker_cancel_cb+0xb7/0x210 fs/io-wq.c:187
but task is already holding lock: ffff88801aa98018 (&wqe->lock){+.+.}-{2:2}, at: io_wq_worker_sleeping+0xb6/0x140 fs/io-wq.c:700
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&wqe->lock);
lock(&wqe->lock);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by iou-wrk-6468/6471:
#0: ffff88801aa98018 (&wqe->lock){+.+.}-{2:2}, at: io_wq_worker_sleeping+0xb6/0x140 fs/io-wq.c:700
This commit marks accesses to the rcu_state.n_force_qs. These data
races are hard to make happen, but syzkaller was equal to the task.
Reported-by: syzbot+e08a83a1940ec3846cd5@syzkaller.appspotmail.com Acked-by: Marco Elver <elver@google.com> Signed-off-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We check IO_WQ_BIT_EXIT before attempting to create a new worker, and
wq exit cancels pending work if we have any. But it's possible to have
a race between the two, where creation checks exit finding it not set,
but we're in the process of exiting. The exit side will cancel pending
creation task_work, but there's a gap where we add task_work after we've
canceled existing creations at exit time.
Fix this by checking the EXIT bit post adding the creation task_work.
If it's set, run the same cancelation that exit does.
There's a small race here where the task_work could finish and drop
the worker itself, so that by the time that task_work_add() returns
with a successful addition we've already put the worker.
The worker callbacks clear this bit themselves, so we don't actually
need to manually clear it in the caller. Get rid of it.
In resp_mode_select() sanity check the block descriptor len to avoid UAF.
BUG: KASAN: use-after-free in resp_mode_select+0xa4c/0xb40 drivers/scsi/scsi_debug.c:2509
Read of size 1 at addr ffff888026670f50 by task scsicmd/15032
Change min_t() to use type "u32" instead of type "int" to avoid stack out
of bounds. With min_t() type "int" the values get sign extended and the
larger value gets used causing stack out of bounds.
BUG: KASAN: stack-out-of-bounds in memcpy include/linux/fortify-string.h:191 [inline]
BUG: KASAN: stack-out-of-bounds in sg_copy_buffer+0x1de/0x240 lib/scatterlist.c:976
Read of size 127 at addr ffff888072607128 by task syz-executor.7/18707
If the size arg to kcalloc() is zero, it returns ZERO_SIZE_PTR. Because of
that, for a following NULL pointer check to work on the returned pointer,
kcalloc() must not be called with the size arg equal to zero. Return early
without error before the kcalloc() call if size arg is zero.
BUG: KASAN: null-ptr-deref in memcpy include/linux/fortify-string.h:191 [inline]
BUG: KASAN: null-ptr-deref in sg_copy_buffer+0x138/0x240 lib/scatterlist.c:974
Write of size 4 at addr 0000000000000010 by task syz-executor.1/22789
Syzbot triggered the following warning in ovl_workdir_create() ->
ovl_create_real():
if (!err && WARN_ON(!newdentry->d_inode)) {
The reason is that the cgroup2 filesystem returns from mkdir without
instantiating the new dentry.
Weird filesystems such as this will be rejected by overlayfs at a later
stage during setup, but to prevent such a warning, call ovl_mkdir_real()
directly from ovl_workdir_create() and reject this case early.
Since mxl111sf_* devices call mxl111sf_ctrl_msg() in ->frontend_attach()
internally we need to initialize state->msg_lock before
frontend_attach(). To achieve it, ->probe() call added to all mxl111sf_*
devices, which will simply initiaize mutex.
Reported-and-tested-by: syzbot+5ca0bf339f13c4243001@syzkaller.appspotmail.com Fixes: 8572211842af ("[media] mxl111sf: convert to new DVB USB") Signed-off-by: Pavel Skripkin <paskripkin@gmail.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USBDEVFS_CONTROL and USBDEVFS_BULK ioctls invoke
usb_start_wait_urb(), which contains an uninterruptible wait with a
user-specified timeout value. If timeout value is very large and the
device being accessed does not respond in a reasonable amount of time,
the kernel will complain about "Task X blocked for more than N
seconds", as found in testing by syzbot:
To fix this problem, this patch replaces usbfs's calls to
usb_control_msg() and usb_bulk_msg() with special-purpose code that
does essentially the same thing (as recommended in the comment for
usb_start_wait_urb()), except that it always uses a killable wait and
it uses GFP_KERNEL rather than GFP_NOIO.
Reported-and-tested-by: syzbot+ada0f7d3d9fd2016d927@syzkaller.appspotmail.com Suggested-by: Oliver Neukum <oneukum@suse.com> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/20210903175312.GA468440@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The verifier checks that PTR_TO_BTF_ID pointer is either valid or NULL,
but it cannot distinguish IS_ERR pointer from valid one.
When offset is added to IS_ERR pointer it may become small positive
value which is a user address that is not handled by extable logic
and has to be checked for at the runtime.
Tighten BPF_PROBE_MEM pointer check code to prevent this case.
Fixes: 4c5de127598e ("bpf: Emit explicit NULL pointer checks for PROBE_LDX instructions.") Reported-by: Lorenzo Fontana <lorenzo.fontana@elastic.co> Signed-off-by: Alexei Starovoitov <ast@kernel.org> Acked-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a single reg version of maybe_emit_mod() and factor out
common code in more cases.
Signed-off-by: Jie Meng <jmeng@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Song Liu <songliubraving@fb.com> Link: https://lore.kernel.org/bpf/20211006194135.608932-1-jmeng@fb.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not sleep in poll() when the need_wakeup flag is set. When this
flag is set, the application needs to explicitly wake up the driver
with a syscall (poll, recvmsg, sendmsg, etc.) to guarantee that Rx
and/or Tx processing will be processed promptly. But the current code
in poll(), sleeps first then wakes up the driver. This means that no
driver processing will occur (baring any interrupts) until the timeout
has expired.
Fix this by checking the need_wakeup flag first and if set, wake the
driver and return to the application. Only if need_wakeup is not set
should the process sleep if there is a timeout set in the poll() call.
Fixes: 77cd0d7b3f25 ("xsk: add support for need_wakeup flag in AF_XDP rings") Reported-by: Keith Wiles <keith.wiles@intel.com> Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Link: https://lore.kernel.org/bpf/20211214102607.7677-1-magnus.karlsson@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The relevant datasheet [1] specifies nonstandard limits for the bit timing
parameters. While it is unclear what the exact effect of violating these
limits is, it seems like a good idea to adhere to the documentation.
[1] Intel Atom® x6000E Series, and Intel® Pentium® and Celeron® N and J
Series Processors for IoT Applications Datasheet,
Volume 2 (Book 3 of 3), July 2021, Revision 001
Livepatching a loaded module involves applying relocations through
apply_relocate_add(), which attempts to write to read-only memory when
CONFIG_STRICT_MODULE_RWX=y. Work around this by performing these
writes through the text poke area by using patch_instruction().
R_PPC_REL24 is the only relocation type generated by the kpatch-build
userspace tool or klp-convert kernel tree that I observed applying a
relocation to a post-init module.
A more comprehensive solution is planned, but using patch_instruction()
for R_PPC_REL24 on should serve as a sufficient fix.
This does have a performance impact, I observed ~15% overhead in
module_load() on POWER8 bare metal with checksum verification off.
Fixes: c35717c71e98 ("powerpc: Set ARCH_HAS_STRICT_MODULE_RWX") Cc: stable@vger.kernel.org # v5.14+ Reported-by: Joe Lawrence <joe.lawrence@redhat.com> Signed-off-by: Russell Currey <ruscur@russell.cc> Tested-by: Joe Lawrence <joe.lawrence@redhat.com>
[mpe: Check return codes from patch_instruction()] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/20211214121248.777249-1-mpe@ellerman.id.au Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fixed commit attempts to get the output file descriptor even if the
file was never opened e.g.
$ perf record uname
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB perf.data (7 samples) ]
$ perf inject -i perf.data --vm-time-correlation=dry-run
Segmentation fault (core dumped)
$ gdb --quiet perf
Reading symbols from perf...
(gdb) r inject -i perf.data --vm-time-correlation=dry-run
Starting program: /home/ahunter/bin/perf inject -i perf.data --vm-time-correlation=dry-run
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/x86_64-linux-gnu/libthread_db.so.1".
Program received signal SIGSEGV, Segmentation fault.
__GI___fileno (fp=0x0) at fileno.c:35
35 fileno.c: No such file or directory.
(gdb) bt
#0 __GI___fileno (fp=0x0) at fileno.c:35
#1 0x00005621e48dd987 in perf_data__fd (data=0x7fff4c68bd08) at util/data.h:72
#2 perf_data__fd (data=0x7fff4c68bd08) at util/data.h:69
#3 cmd_inject (argc=<optimized out>, argv=0x7fff4c69c1f0) at builtin-inject.c:1017
#4 0x00005621e4936783 in run_builtin (p=0x5621e4ee6878 <commands+600>, argc=4, argv=0x7fff4c69c1f0) at perf.c:313
#5 0x00005621e4897d5c in handle_internal_command (argv=<optimized out>, argc=<optimized out>) at perf.c:365
#6 run_argv (argcp=<optimized out>, argv=<optimized out>) at perf.c:409
#7 main (argc=4, argv=0x7fff4c69c1f0) at perf.c:539
(gdb)
Fixes: 0ae03893623dd1dd ("perf tools: Pass a fd to perf_file_header__read_pipe()") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Riccardo Mancini <rickyman7@gmail.com> Cc: stable@vger.kernel.org Link: http://lore.kernel.org/lkml/20211213084829.114772-3-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fixed commit attempts to close inject.output even if it was never
opened e.g.
$ perf record uname
Linux
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.002 MB perf.data (7 samples) ]
$ perf inject -i perf.data --vm-time-correlation=dry-run
Segmentation fault (core dumped)
$ gdb --quiet perf
Reading symbols from perf...
(gdb) r inject -i perf.data --vm-time-correlation=dry-run
Starting program: /home/ahunter/bin/perf inject -i perf.data --vm-time-correlation=dry-run
[Thread debugging using libthread_db enabled]
Using host libthread_db library "/lib/x86_64-linux-gnu/libthread_db.so.1".
Program received signal SIGSEGV, Segmentation fault.
0x00007eff8afeef5b in _IO_new_fclose (fp=0x0) at iofclose.c:48
48 iofclose.c: No such file or directory.
(gdb) bt
#0 0x00007eff8afeef5b in _IO_new_fclose (fp=0x0) at iofclose.c:48
#1 0x0000557fc7b74f92 in perf_data__close (data=data@entry=0x7ffcdafa6578) at util/data.c:376
#2 0x0000557fc7a6b807 in cmd_inject (argc=<optimized out>, argv=<optimized out>) at builtin-inject.c:1085
#3 0x0000557fc7ac4783 in run_builtin (p=0x557fc8074878 <commands+600>, argc=4, argv=0x7ffcdafb6a60) at perf.c:313
#4 0x0000557fc7a25d5c in handle_internal_command (argv=<optimized out>, argc=<optimized out>) at perf.c:365
#5 run_argv (argcp=<optimized out>, argv=<optimized out>) at perf.c:409
#6 main (argc=4, argv=0x7ffcdafb6a60) at perf.c:539
(gdb)
Fixes: 02e6246f5364d526 ("perf inject: Close inject.output on exit") Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Riccardo Mancini <rickyman7@gmail.com> Cc: stable@vger.kernel.org Link: http://lore.kernel.org/lkml/20211213084829.114772-2-adrian.hunter@intel.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Per HiFive Unmatched schematics, the card detect signal of the
micro SD card is connected to gpio pin #15, which should be
reflected in the DT via the <gpios> property, as described in
Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt.
Per HiFive Unleashed schematics, the card detect signal of the
micro SD card is connected to gpio pin #11, which should be
reflected in the DT via the <gpios> property, as described in
Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt.
Optimistic spinning needs to be terminated when the spinning waiter is not
longer the top waiter on the lock, but the condition is negated. It
terminates if the waiter is the top waiter, which is defeating the whole
purpose.
mount.cifs can pass a device with multiple delimiters in it. This will
cause rename(2) to fail with ENOENT.
V2:
- Make sanitize_path more readable.
- Fix multiple delimiters between UNC and prepath.
- Avoid a memory leak if a bad user starts putting a lot of delimiters
in the path on purpose.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=2031200 Fixes: 24e0a1eff9e2 ("cifs: switch to new mount api") Cc: stable@vger.kernel.org # 5.11+ Acked-by: Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by: Thiago Rafael Becker <trbecker@gmail.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even after commit e1d7ba873555 ("time: Always make sure wall_to_monotonic
isn't positive") it is still possible to make wall_to_monotonic positive
by running the following code:
The reason is that the second parameter of timespec64_compare(), ts_delta,
may be unnormalized because the delta is calculated with an open coded
substraction which causes the comparison of tv_sec to yield the wrong
result:
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866") Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com> Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The donation calculation logic assumes that the donor has non-zero
after-donation hweight, so the lowest active hweight a donating cgroup can
have is 2 so that it can donate 1 while keeping the other 1 for itself.
Earlier, we only donated from cgroups with sizable surpluses so this
condition was always true. However, with the precise donation algorithm
implemented, f1de2439ec43 ("blk-iocost: revamp donation amount
determination") made the donation amount calculation exact enabling even low
hweight cgroups to donate.
This means that in rare occasions, a cgroup with active hweight of 1 can
enter donation calculation triggering the following warning and then a
divide-by-zero oops.
Fix it by excluding cgroups w/ active hweight < 2 from donating. Excluding
these extreme low hweight donations shouldn't affect work conservation in
any meaningful way.
The function btrfs_scan_one_device() calls blkdev_get_by_path() and
blkdev_put() to get and release its target block device. However, when
btrfs_sb_log_location_bdev() fails, blkdev_put() is not called and the
block device is left without clean up. This triggered failure of fstests
generic/085. Fix the failure path of btrfs_sb_log_location_bdev() to
call blkdev_put().
Fixes: 12659251ca5df ("btrfs: implement log-structured superblock for ZONED mode") CC: stable@vger.kernel.org # 5.15+ Reviewed-by: Nikolay Borisov <nborisov@suse.com> Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Filipe reported a hang when we have errors on btrfs. This turned out to
be a side-effect of my fix c2e39305299f01 ("btrfs: clear extent buffer
uptodate when we fail to write it") which made it so we clear
EXTENT_BUFFER_UPTODATE on an eb when we fail to write it out.
Below is a paste of Filipe's analysis he got from using drgn to debug
the hang
"""
btree readahead code calls read_extent_buffer_pages(), sets ->io_pages to
a value while writeback of all pages has not yet completed:
--> writeback for the first 3 pages finishes, we clear
EXTENT_BUFFER_UPTODATE from eb on the first page when we get an
error.
--> at this point eb->io_pages is 1 and we cleared Uptodate bit from the
first 3 pages
--> read_extent_buffer_pages() does not see EXTENT_BUFFER_UPTODATE() so
it continues, it's able to lock the pages since we obviously don't
hold the pages locked during writeback
--> read_extent_buffer_pages() then computes 'num_reads' as 3, and sets
eb->io_pages to 3, since only the first page does not have Uptodate
bit set at this point
--> writeback for the remaining page completes, we ended decrementing
eb->io_pages by 1, resulting in eb->io_pages == 2, and therefore
never calling end_extent_buffer_writeback(), so
EXTENT_BUFFER_WRITEBACK remains in the eb's flags
--> of course, when the read bio completes, it doesn't and shouldn't
call end_extent_buffer_writeback()
--> we should clear EXTENT_BUFFER_UPTODATE only after all pages of
the eb finished writeback? or maybe make the read pages code
wait for writeback of all pages of the eb to complete before
checking which pages need to be read, touch ->io_pages, submit
read bio, etc
writeback bit never cleared means we can hang when aborting a
transaction, at:
This is a problem because our writes are not synchronized with reads in
any way. We clear the UPTODATE flag and then we can easily come in and
try to read the EB while we're still waiting on other bio's to
complete.
We have two options here, we could lock all the pages, and then check to
see if eb->io_pages != 0 to know if we've already got an outstanding
write on the eb.
Or we can simply check to see if we have WRITE_ERR set on this extent
buffer. We set this bit _before_ we clear UPTODATE, so if the read gets
triggered because we aren't UPTODATE because of a write error we're
guaranteed to have WRITE_ERR set, and in this case we can simply return
-EIO. This will fix the reported hang.
Reported-by: Filipe Manana <fdmanana@suse.com> Fixes: c2e39305299f01 ("btrfs: clear extent buffer uptodate when we fail to write it") CC: stable@vger.kernel.org # 5.4+ Reviewed-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When creating a subvolume, at create_subvol(), we allocate an anonymous
device and later call btrfs_get_new_fs_root(), which in turn just calls
btrfs_get_root_ref(). There we call btrfs_init_fs_root() which assigns
the anonymous device to the root, but if after that call there's an error,
when we jump to 'fail' label, we call btrfs_put_root(), which frees the
anonymous device and then returns an error that is propagated back to
create_subvol(). Than create_subvol() frees the anonymous device again.
When this happens, if the anonymous device was not reallocated after
the first time it was freed with btrfs_put_root(), we get a kernel
message like the following:
(...)
[13950.282466] BTRFS: error (device dm-0) in create_subvol:663: errno=-5 IO failure
[13950.283027] ida_free called for id=65 which is not allocated.
[13950.285974] BTRFS info (device dm-0): forced readonly
(...)
If the anonymous device gets reallocated by another btrfs filesystem
or any other kernel subsystem, then bad things can happen.
So fix this by setting the root's anonymous device to 0 at
btrfs_get_root_ref(), before we call btrfs_put_root(), if an error
happened.
Fixes: 2dfb1e43f57dd3 ("btrfs: preallocate anon block device at first phase of snapshot creation") CC: stable@vger.kernel.org # 5.10+ Reviewed-by: Qu Wenruo <wqu@suse.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Line 1169 (#3) allocates a memory chunk for victim_name by kmalloc(),
but when the function returns in line 1184 (#4) victim_name allocated
by line 1169 (#3) is not freed, which will lead to a memory leak.
There is a similar snippet of code in this function as allocating a memory
chunk for victim_name in line 1104 (#1) as well as releasing the memory
in line 1116 (#2).
We should kfree() victim_name when the return value of backref_in_log()
is less than zero and before the function returns in line 1184 (#4).
Cc: stable@vger.kernel.org Fixes: 69c4a42d72eb ("lsm,selinux: add new hook to compare new mount to an existing mount") Signed-off-by: Scott Mayhew <smayhew@redhat.com>
[PM: cleanup/line-wrap the backtrace] Signed-off-by: Paul Moore <paul@paul-moore.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When generalising GPIO support and adding support for CP2102N, the GPIO
registration for some CP2105 devices accidentally broke. Specifically,
when all the pins of a port are in "modem" mode, and thus unavailable
for GPIO use, the GPIO chip would now be registered without having
initialised the number of GPIO lines. This would in turn be rejected by
gpiolib and some errors messages would be printed (but importantly probe
would still succeed).
Fix this by initialising the number of GPIO lines before registering the
GPIO chip.
Note that as for the other device types, and as when all CP2105 pins are
muxed for LED function, the GPIO chip is registered also when no pins
are available for GPIO use.
When listening for notifications through netlink of a new interface being
registered, sporadically, it is possible for the MAC to be read as zero.
The zero MAC address lasts a short period of time and then switches to a
valid random MAC address.
This causes problems for netd in Android, which assumes that the interface
is malfunctioning and will not use it.
In the good case we get this log:
InterfaceController::getCfg() ifName usb0
hwAddr 92:a8:f0:73:79:5b ipv4Addr 0.0.0.0 flags 0x1002
In the error case we get these logs:
InterfaceController::getCfg() ifName usb0
hwAddr 00:00:00:00:00:00 ipv4Addr 0.0.0.0 flags 0x1002
The reason for the issue is the order in which the interface is setup,
it is first registered through register_netdev() and after the MAC
address is set.
Fixed by first setting the MAC address of the net_device and after that
calling register_netdev().
Fixes: bcd4a1c40bee885e ("usb: gadget: u_ether: construct with default values and add setters/getters") Cc: stable@vger.kernel.org Signed-off-by: Marian Postevca <posteuca@mutex.one> Link: https://lore.kernel.org/r/20211204214912.17627-1-posteuca@mutex.one Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In current design, when the tcpm port is unregisterd, the kthread_worker
will be destroyed in the last step. Inside the kthread_destroy_worker(),
the worker will flush all the works and wait for them to end. However, if
one of the works calls hrtimer_start(), this hrtimer will be pending until
timeout even though tcpm port is removed. Once the hrtimer timeout, many
strange kernel dumps appear.
Thus, we can first complete kthread_destroy_worker(), then cancel all the
hrtimers. This will guarantee that no hrtimer is pending at the end.
Fixes: 3ed8e1c2ac99 ("usb: typec: tcpm: Migrate workqueue to RT priority for processing events")
cc: <stable@vger.kernel.org> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Signed-off-by: Xu Yang <xu.yang_2@nxp.com> Link: https://lore.kernel.org/r/20211209101507.499096-1-xu.yang_2@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch puts content of cdnsp_gadget_pullup function inside
spin_lock_irqsave and spin_lock_restore section.
This construction is required here to keep the data consistency,
otherwise some data can be changed e.g. from interrupt context.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") Reported-by: Ken (Jian) He <jianhe@ambarella.com>
cc: <stable@vger.kernel.org> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Reviewed-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20211214045527.26823-1-pawell@gli-login.cadence.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch restrict calling of cdnsp_died function during removing modules
or software disconnect.
This function was called because after transition controller to HALT
state the driver starts handling the deferred interrupt.
In this case such interrupt can be simple ignored.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: <stable@vger.kernel.org> Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Link: https://lore.kernel.org/r/20211210112945.660-1-pawell@gli-login.cadence.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch fixes incorrect status for control request.
Without this fix all usb_request objects were returned to upper drivers
with usb_reqest->status field set to -EINPROGRESS.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
cc: <stable@vger.kernel.org> Reported-by: Ken (Jian) He <jianhe@ambarella.com> Reviewed-by: Peter Chen <peter.chen@kernel.org> Signed-off-by: Pawel Laszczak <pawell@cadence.com> Link: https://lore.kernel.org/r/20211207091838.39572-1-pawell@gli-login.cadence.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masking all unused MSI-X entries is done to ensure that a crash kernel
starts from a clean slate, which correponds to the reset state of the
device as defined in the PCI-E specificion 3.0 and later:
Vector Control for MSI-X Table Entries
--------------------------------------
"00: Mask bit: When this bit is set, the function is prohibited from
sending a message using this MSI-X Table entry.
...
This bit’s state after reset is 1 (entry is masked)."
A Marvell NVME device fails to deliver MSI interrupts after trying to
enable MSI-X interrupts due to that masking. It seems to take the MSI-X
mask bits into account even when MSI-X is disabled.
While not specification compliant, this can be cured by moving the masking
into the success path, so that the MSI-X table entries stay in device reset
state when the MSI-X setup fails.
[ tglx: Move it into the success path, add comment and amend changelog ]
Fixes: aa8092c1d1f1 ("PCI/MSI: Mask all unused MSI-X entries") Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: linux-pci@vger.kernel.org Cc: Bjorn Helgaas <bhelgaas@google.com> Cc: Michal Simek <michal.simek@xilinx.com> Cc: Marek Vasut <marex@denx.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211210161025.3287927-1-sr@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PCI_MSIX_FLAGS_MASKALL is set in the MSI-X control register at MSI-X
interrupt setup time. It's cleared on success, but the error handling path
only clears the PCI_MSIX_FLAGS_ENABLE bit.
That's incorrect as the reset state of the PCI_MSIX_FLAGS_MASKALL bit is
zero. That can be observed via lspci:
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.
Fixes: a415083a11cc ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS") Cc: stable <stable@vger.kernel.org> Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com> Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com> Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting that an unprivileged user who logged in from tty
console can crash the system using a reproducer shown below [1], for
n_hdlc_tty_wakeup() is synchronously calling n_hdlc_send_frames().
int main(int argc, char *argv[])
{
const int disc = 0xd;
ioctl(1, TIOCSETD, &disc);
while (1) {
ioctl(1, TCXONC, 0);
write(1, "", 1);
ioctl(1, TCXONC, 1); /* Kernel panic - not syncing: scheduling while atomic */
}
}
----------
Linus suspected that "struct tty_ldisc"->ops->write_wakeup() must not
sleep, and Jiri confirmed it from include/linux/tty_ldisc.h. Thus, defer
n_hdlc_send_frames() from n_hdlc_tty_wakeup() to a WQ context like
net/nfc/nci/uart.c does.
Link: https://syzkaller.appspot.com/bug?extid=5f47a8cea6a12b77a876 Reported-by: syzbot <syzbot+5f47a8cea6a12b77a876@syzkaller.appspotmail.com> Cc: stable <stable@vger.kernel.org> Analyzed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com> Suggested-by: Linus Torvalds <torvalds@linux-foundation.org> Confirmed-by: Jiri Slaby <jirislaby@kernel.org> Reviewed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Link: https://lore.kernel.org/r/40de8b7e-a3be-4486-4e33-1b1d1da452f8@i-love.sakura.ne.jp Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ability to write to MSR_IA32_PERF_CAPABILITIES from the host should
not depend on guest visible CPUID entries, even if just to allow
creating/restoring guest MSRs and CPUIDs in any sequence.
Fixes: 27461da31089 ("KVM: x86/pmu: Support full width counting") Suggested-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20211216165213.338923-3-vkuznets@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
This change causes boot lockups when using "arlyprintk=xdbc" because
ktime can not be used at this point in time in the boot process. Also,
it is not needed for very small delays like this.
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
When CONFIG_FSL_PMC is set to n, no value is assigned to cpu_up_prepare
in the mpc85xx_pm_ops structure. As a result, oops is triggered in
smp_85xx_start_cpu().
The libbpf CI reported occasional failure in btf_skc_cls_ingress:
test_syncookie:FAIL:Unexpected syncookie states gen_cookie:80326634 recv_cookie:0
bpf prog error at line 97
"error at line 97" means the bpf prog cannot find the listening socket
when the final ack is received. It then skipped processing
the syncookie in the final ack which then led to "recv_cookie:0".
The problem is the userspace program did not do accept() and went
ahead to close(listen_fd) before the kernel (and the bpf prog) had
a chance to process the final ack.
The fix is to add accept() call so that the userspace will wait for
the kernel to finish processing the final ack first before close()-ing
everything.
Fixes: 9a856cae2217 ("bpf: selftest: Add test_btf_skc_cls_ingress") Reported-by: Andrii Nakryiko <andrii@kernel.org> Signed-off-by: Martin KaFai Lau <kafai@fb.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20211216191630.466151-1-kafai@fb.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The prog - start_of_ldx is the offset before the faulting ldx to the location
after it, so this will be used to adjust pt_regs->ip for jumping over it and
continuing, and with old temp it would have been fixed up to the wrong offset,
causing crash.
Fixes: 4c5de127598e ("bpf: Emit explicit NULL pointer checks for PROBE_LDX instructions.") Signed-off-by: Alexei Starovoitov <ast@kernel.org> Reviewed-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Return code is not set to an error code in load_other_segments() when
of_kexec_alloc_and_setup_fdt() call returns a NULL dtb. This results
in status success (return code set to 0) being returned from
load_other_segments().
Set return code to -EINVAL if of_kexec_alloc_and_setup_fdt() returns
NULL dtb.
Signed-off-by: Lakshmi Ramasubramanian <nramas@linux.microsoft.com> Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: ac10be5cdbfa ("arm64: Use common of_kexec_alloc_and_setup_fdt()") Link: https://lore.kernel.org/r/20211210010121.101823-1-nramas@linux.microsoft.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix afs_add_open_map() to check that the vnode isn't already on the list
when it adds it. It's possible that afs_drop_open_mmap() decremented
the cb_nr_mmap counter, but hadn't yet got into the locked section to
remove it.
Also vnode->cb_mmap_link should be initialised, so fix that too.
The descriptor list is a shared resource across all of the transmit queues, and
the locking mechanism used today only protects concurrency across a given
transmit queue between the transmit and reclaiming. This creates an opportunity
for the SYSTEMPORT hardware to work on corrupted descriptors if we have
multiple producers at once which is the case when using multiple transmit
queues.
This was particularly noticeable when using multiple flows/transmit queues and
it showed up in interesting ways in that UDP packets would get a correct UDP
header checksum being calculated over an incorrect packet length. Similarly TCP
packets would get an equally correct checksum computed by the hardware over an
incorrect packet length.
The SYSTEMPORT hardware maintains an internal descriptor list that it re-arranges
when the driver produces a new descriptor anytime it writes to the
WRITE_PORT_{HI,LO} registers, there is however some delay in the hardware to
re-organize its descriptors and it is possible that concurrent TX queues
eventually break this internal allocation scheme to the point where the
length/status part of the descriptor gets used for an incorrect data buffer.
The fix is to impose a global serialization for all TX queues in the short
section where we are writing to the WRITE_PORT_{HI,LO} registers which solves
the corruption even with multiple concurrent TX queues being used.
In nginx/wrk benchmark, there's a hung problem with high probability
on case likes that: (client will last several minutes to exit)
server: smc_run nginx
client: smc_run wrk -c 10000 -t 1 http://server
Client hangs with the following backtrace:
0 [ffffa7ce8Of3bbf8] __schedule at ffffffff9f9eOd5f
1 [ffffa7ce8Of3bc88] schedule at ffffffff9f9eløe6
2 [ffffa7ce8Of3bcaO] schedule_timeout at ffffffff9f9e3f3c
3 [ffffa7ce8Of3bd2O] wait_for_common at ffffffff9f9el9de
4 [ffffa7ce8Of3bd8O] __flush_work at ffffffff9fOfeOl3
5 [ffffa7ce8øf3bdfO] smc_release at ffffffffcO697d24 [smc]
6 [ffffa7ce8Of3be2O] __sock_release at ffffffff9f8O2e2d
7 [ffffa7ce8Of3be4ø] sock_close at ffffffff9f8ø2ebl
8 [ffffa7ce8øf3be48] __fput at ffffffff9f334f93
9 [ffffa7ce8Of3be78] task_work_run at ffffffff9flOlff5
10 [ffffa7ce8Of3beaO] do_exit at ffffffff9fOe5Ol2
11 [ffffa7ce8Of3bflO] do_group_exit at ffffffff9fOe592a
12 [ffffa7ce8Of3bf38] __x64_sys_exit_group at ffffffff9fOe5994
13 [ffffa7ce8Of3bf4O] do_syscall_64 at ffffffff9f9d4373
14 [ffffa7ce8Of3bfsO] entry_SYSCALL_64_after_hwframe at ffffffff9fa0007c
This issue dues to flush_work(), which is used to wait for
smc_connect_work() to finish in smc_release(). Once lots of
smc_connect_work() was pending or all executing work dangling,
smc_release() has to block until one worker comes to free, which
is equivalent to wait another smc_connnect_work() to finish.
In order to fix this, There are two changes:
1. For those idle smc_connect_work(), cancel it from the workqueue; for
executing smc_connect_work(), waiting for it to finish. For that
purpose, replace flush_work() with cancel_work_sync().
2. Since smc_connect() hold a reference for passive closing, if
smc_connect_work() has been cancelled, release the reference.
Fixes: 24ac3a08e658 ("net/smc: rebuild nonblocking connect") Reported-by: Tony Lu <tonylu@linux.alibaba.com> Tested-by: Dust Li <dust.li@linux.alibaba.com> Reviewed-by: Dust Li <dust.li@linux.alibaba.com> Reviewed-by: Tony Lu <tonylu@linux.alibaba.com> Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Link: https://lore.kernel.org/r/1639571361-101128-1-git-send-email-alibuda@linux.alibaba.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When printing netdev features %pNF already takes care of the 0x prefix,
remove the explicit one.
Fixes: 6413139dfc64 ("skbuff: increase verbosity when dumping skb data") Signed-off-by: Gal Pressman <gal@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
KASAN reports an out-of-bounds read in rk_gmac_setup on the line:
while (ops->regs[i]) {
This happens for most platforms since the regs flexible array member is
empty, so the memory after the ops structure is being read here. It
seems that mostly this happens to contain zero anyway, so we get lucky
and everything still works.
To avoid adding redundant data to nearly all the ops structures, add a
new flag to indicate whether the regs field is valid and avoid this loop
when it is not.
Fixes: 3bb3d6b1c195 ("net: stmmac: Add RK3566/RK3568 SoC support") Signed-off-by: John Keeping <john@metanate.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Packet sockets may switch ring versions. Avoid misinterpreting state
between versions, whose fields share a union. rx_owner_map is only
allocated with a packet ring (pg_vec) and both are swapped together.
If pg_vec is NULL, meaning no packet ring was allocated, then neither
was rx_owner_map. And the field may be old state from a tpacket_v3.
Fixes: 61fad6816fc1 ("net/packet: tpacket_rcv: avoid a producer race condition") Reported-by: Syzbot <syzbot+1ac0994a0a0c55151121@syzkaller.appspotmail.com> Signed-off-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20211215143937.106178-1-willemdebruijn.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
since it may cause a potential kernel information leak issue, as follows:
1. nsim_bpf_map_alloc calls nsim_map_alloc_elem to allocate elements for
a new map.
2. nsim_map_alloc_elem uses kmalloc to allocate map's value, but doesn't
zero it.
3. A user application can use IOCTL BPF_MAP_LOOKUP_ELEM to get specific
element's information in the map.
4. The kernel function map_lookup_elem will call bpf_map_copy_value to get
the information allocated at step-2, then use copy_to_user to copy to the
user buffer.
This can only leak information for an array map.
Fixes: 395cacb5f1a0 ("netdevsim: bpf: support fake map offload") Suggested-by: Jakub Kicinski <kuba@kernel.org> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com> Link: https://lore.kernel.org/r/20211215111530.72103-1-tcs.kernel@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db7272798 ("ixgbe: Introduce function to control MDIO speed") Signed-off-by: Cyril Novikov <cnovikov@lynx.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:
However, the suppression was not documented at all, nor was how to
enable NBASE-T support.
Properly document the NBASE-T suppression and how to enable NBASE-T
support.
Fixes: a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support") Reported-by: Robert Schlabbach <robert_s@gmx.net> Signed-off-by: Robert Schlabbach <robert_s@gmx.net> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
Fixes: d4e0fe01a38a0 (igbvf: add new driver to support 82576 virtual functions) Reported-by: Zheyu Ma <zheyuma97@gmail.com> Signed-off-by: Letu Ren <fantasquex@gmail.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not.
In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.
Fixes: 25cd5a391478 ("ARM: tegra: Add speedo-based process identification") Link: https://github.com/ClangBuiltLinux/linux/issues/1488 Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
__mptcp_push_pending() may call mptcp_flush_join_list() with subflow
socket lock held. If such call hits mptcp_sockopt_sync_all() then
subsequently __mptcp_sockopt_sync() could try to lock the subflow
socket for itself, causing a deadlock.
Fix the issue by using __mptcp_flush_join_list() instead of plain
mptcp_flush_join_list() inside __mptcp_push_pending(), as suggested by
Florian. The sockopt sync will be deferred to the workqueue.
The mptcp ULP extension relies on sk->sk_sock_kern being set correctly:
It prevents setsockopt(fd, IPPROTO_TCP, TCP_ULP, "mptcp", 6); from
working for plain tcp sockets (any userspace-exposed socket).
But in case of fallback, accept() can return a plain tcp sk.
In such case, sk is still tagged as 'kernel' and setsockopt will work.
This will crash the kernel, The subflow extension has a NULL ctx->conn
mptcp socket:
BUG: KASAN: null-ptr-deref in subflow_data_ready+0x181/0x2b0
Call Trace:
tcp_data_ready+0xf8/0x370
[..]
Fixes: cf7da0d66cc1 ("mptcp: Create SUBFLOW socket for incoming connections") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver has to check if it does not accidentally put the timestamp in
the SKB before previous timestamp gets overwritten.
Timestamp values in the PHY are read only and do not get cleared except
at hardware reset or when a new timestamp value is captured.
The cached_tstamp field is used to detect the case where a new timestamp
has not yet been captured, ensuring that we avoid sending stale
timestamp data to the stack.
Fixes: ea9b847cda64 ("ice: enable transmit timestamps for E810 devices") Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Change the division in ice_ptp_adjfine from div_u64 to div64_u64.
div_u64 is used when the divisor is 32 bit but in this case incval is
64 bit and it caused incorrect calculations and incval adjustments.
Fixes: 06c16d89d2cb ("ice: register 1588 PTP clock device object for E810 devices") Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com> Tested-by: Gurucharan G <gurucharanx.g@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
We need to return EOPNOTSUPP for the unsupported mpls action type when
setup the flow action.
In the original implement, we will return 0 for the unsupported mpls
action type, actually we do not setup it and the following actions
to the flow action entry.
Fixes: 9838b20a7fb2 ("net: sched: take rtnl lock in tc_setup_flow_action()") Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The above issue is due to previous incorrect implementation of
tc_del_vlan_flow(), shown below, that uses flow_cls_offload_flow_rule()
to get struct flow_rule *rule which is no longer valid for tc filter
delete operation.
So, to ensure tc_del_vlan_flow() deletes the right VLAN cls record for
earlier configured RX queue (configured by hw_tc) in tc_add_vlan_flow(),
this patch introduces stmmac_rfs_entry as driver-side flow_cls_offload
record for 'RX frame steering' tc flower, currently used for VLAN
priority. The implementation has taken consideration for future extension
to include other type RX frame steering such as EtherType based.
v2:
- Clean up overly extensive backtrace and rewrite git message to better
explain the kernel NULL pointer issue.
Fixes: 0e039f5cf86c ("net: stmmac: add RX frame steering based on VLAN priority in tc flower") Tested-by: Kurt Kanzenbach <kurt@linutronix.de> Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
We should be doing the HE capabilities lookup based on the full
interface type so if P2P doesn't have HE but client has it doesn't
get confused. Fix that.
The function cfg80211_reg_can_beacon_relax() expects wiphy
mutex to be held when it is being called. However, when
reg_leave_invalid_chans() is called the mutex is not held.
Fix it by acquiring the lock before calling the function.
When we call ieee80211_agg_start_txq(), that will in turn call
schedule_and_wake_txq(). Called from ieee80211_stop_tx_ba_cb()
this is done under sta->lock, which leads to certain circular
lock dependencies, as reported by Chris Murphy:
https://lore.kernel.org/r/CAJCQCtSXJ5qA4bqSPY=oLRMbv-irihVvP7A2uGutEbXQVkoNaw@mail.gmail.com
In general, ieee80211_agg_start_txq() is usually not called
with sta->lock held, only in this one place. But it's always
called with sta->ampdu_mlme.mtx held, and that's therefore
clearly sufficient.
Change ieee80211_stop_tx_ba_cb() to also call it without the
sta->lock held, by factoring it out of ieee80211_remove_tid_tx()
(which is only called in this one place).
This breaks the locking chain and makes it less likely that
we'll have similar locking chain problems in the future.
Fixes: ba8c3d6f16a1 ("mac80211: add an intermediate software queue implementation") Reported-by: Chris Murphy <lists@colorremedies.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Link: https://lore.kernel.org/r/iwlwifi.20211202152554.f519884c8784.I555fef8e67d93fff3d9a304886c4a9f8b322e591@changeid Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log