The decision whether to enable a wake irq during suspend can not be done
based on the runtime PM state directly as a driver may use wake irqs
without implementing runtime PM. Such drivers specifically leave the
state set to the default 'suspended' and the wake irq is thus never
enabled at suspend.
Add a new wake irq flag to track whether a dedicated wake irq has been
enabled at runtime suspend and therefore must not be enabled at system
suspend.
Note that pm_runtime_enabled() can not be used as runtime PM is always
disabled during late suspend.
Fixes: 69728051f5bf ("PM / wakeirq: Fix unbalanced IRQ enable for wakeirq") Cc: 4.16+ <stable@vger.kernel.org> # 4.16+ Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the dedicated wake IRQ is level trigger, and it uses the
device's low-power status as the wakeup source, that means if the
device is not in low-power state, the wake IRQ will be triggered
if enabled; For this case, need enable the wake IRQ after running
the device's ->runtime_suspend() which make it enter low-power state.
e.g.
Assume the wake IRQ is a low level trigger type, and the wakeup
signal comes from the low-power status of the device.
The wakeup signal is low level at running time (0), and becomes
high level when the device enters low-power state (runtime_suspend
(1) is called), a wakeup event at (2) make the device exit low-power
state, then the wakeup signal also becomes low level.
if enable the wake IRQ before running runtime_suspend during (0),
a wake IRQ will arise, it causes resume immediately;
it works if enable wake IRQ ( e.g. at (3) or (4)) after running
->runtime_suspend().
This patch introduces a new status WAKE_IRQ_DEDICATED_REVERSE to
optionally support enabling wake IRQ after running ->runtime_suspend().
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 8527beb12087 ("PM: sleep: wakeirq: fix wake irq arming") Signed-off-by: Sasha Levin <sashal@kernel.org>
The soundwire subsystem uses two completion structures that allow
drivers to wait for soundwire device to become enumerated on the bus and
initialised by their drivers, respectively.
The code implementing the signalling is currently broken as it does not
signal all current and future waiters and also uses the wrong
reinitialisation function, which can potentially lead to memory
corruption if there are still waiters on the queue.
Not signalling future waiters specifically breaks sound card probe
deferrals as codec drivers can not tell that the soundwire device is
already attached when being reprobed. Some codec runtime PM
implementations suffer from similar problems as waiting for enumeration
during resume can also timeout despite the device already having been
enumerated.
In typical use cases, the peripheral becomes pm_runtime active as a
result of the ALSA/ASoC framework starting up a DAI. The parent/child
hierarchy guarantees that the manager device will be fully resumed
beforehand.
There is however a corner case where the manager device may become
pm_runtime active, but without ALSA/ASoC requesting any functionality
from the peripherals. In this case, the hardware peripheral device
will report as ATTACHED and its initialization routine will be
executed. If this initialization routine initiates any sort of
deferred processing, there is a possibility that the manager could
suspend without the peripheral suspend sequence being invoked: from
the pm_runtime framework perspective, the peripheral is *already*
suspended.
To avoid such disconnects between hardware state and pm_runtime state,
this patch adds an asynchronous pm_request_resume() upon successful
attach/initialization which will result in the proper resume/suspend
sequence to be followed on the peripheral side.
To allow running rseq and KVM's rseq selftests as statically linked
binaries, initialize the various "trampoline" pointers to point directly
at the expect glibc symbols, and skip the dlysm() lookups if the rseq
size is non-zero, i.e. the binary is statically linked *and* the libc
registered its own rseq.
Define weak versions of the symbols so as not to break linking against
libc versions that don't support rseq in any capacity.
The KVM selftests in particular are often statically linked so that they
can be run on targets with very limited runtime environments, i.e. test
machines.
Fixes: 233e667e1ae3 ("selftests/rseq: Uplift rseq selftests for compatibility with glibc-2.35") Cc: Aaron Lewis <aaronlewis@google.com> Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230721223352.2333911-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When checking for libc rseq support in the library constructor, don't
only depend on the symbols presence, check that the registration was
completed.
This targets a scenario where the libc has rseq support but it is not
wired for the current architecture in 'bits/rseq.h', we want to fallback
to our internal registration mechanism.
Signed-off-by: Michael Jeanson <mjeanson@efficios.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Link: https://lore.kernel.org/r/20220614154830.1367382-4-mjeanson@efficios.com
Stable-dep-of: 3bcbc20942db ("selftests/rseq: Play nice with binaries statically linked against glibc 2.35+") Signed-off-by: Sasha Levin <sashal@kernel.org>
When hactive is not aligned to 8 pixels, it is aligned accordingly and
hfront porch needs to be reduced the same amount. Unfortunately the front
porch is set to the difference rather than reducing it. There are some
Samsung TVs which can't cope with a front porch of instead of 70.
altmap->free includes the entire free space from which altmap blocks
can be allocated. So when checking whether the kernel is doing altmap
block free, compute the boundary correctly, otherwise memory hotunplug
can fail.
Fixes: 9ef34630a461 ("powerpc/mm: Fallback to RAM if the altmap is unusable") Signed-off-by: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230724181320.471386-1-aneesh.kumar@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
'op-cs' is copied in 'fun->mchip_number' which is used to access the
'mchip_offsets' and the 'rnb_gpio' arrays.
These arrays have NAND_MAX_CHIPS elements, so the index must be below this
limit.
Fix the sanity check in order to avoid the NAND_MAX_CHIPS value. This
would lead to out-of-bound accesses.
Currently, read/write_page_hwecc() and read/write_page_raw() are not
aligned: there is a mismatch in the OOB bytes which are not
read/written at the same offset in both cases (raw vs. hwecc).
This is a real problem when relying on the presence of the Page
Addresses (PA) when using the NAND chip as a boot device, as the
BootROM expects additional data in the OOB area at specific locations.
Rockchip boot blocks are written per 4 x 512 byte sectors per page.
Each page with boot blocks must have a page address (PA) pointer in OOB
to the next page. Pages are written in a pattern depending on the NAND chip ID.
Generate boot block page address and pattern for hwecc in user space
and copy PA data to/from the already reserved last 4 bytes before ECC
in the chip->oob_poi data layout.
Align the different helpers. This change breaks existing jffs2 users.
Fixes: 058e0e847d54 ("mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others") Signed-off-by: Johan Jonker <jbx6244@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/5e782c08-862b-51ae-47ff-3299940928ca@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Rockchip boot blocks are written per 4 x 512 byte sectors per page.
Each page with boot blocks must have a page address (PA) pointer in OOB
to the next page.
The currently advertised free OOB area starts at offset 6, like
if 4 PA bytes were located right after the BBM. This is wrong as the
PA bytes are located right before the ECC bytes.
Fix the layout by allowing access to all bytes between the BBM and the
PA bytes instead of reserving 4 bytes right after the BBM.
This change breaks existing jffs2 users.
Fixes: 058e0e847d54 ("mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others") Signed-off-by: Johan Jonker <jbx6244@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/d202f12d-188c-20e8-f2c2-9cc874ad4d22@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Ext2 has fields in superblock reserved for subblock allocation support.
However that never landed. Drop the many years dead code.
Reported-by: syzbot+af5e10f73dbff48f70af@syzkaller.appspotmail.com Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reconfigure / remount code takes a lot of effort to protect
filesystem's reconfiguration code from racing writes on remounting
read-only. However during remounting read-only filesystem to read-write
mode userspace writes can start immediately once we clear SB_RDONLY
flag. This is inconvenient for example for ext4 because we need to do
some writes to the filesystem (such as preparation of quota files)
before we can take userspace writes so we are clearing SB_RDONLY flag
before we are fully ready to accept userpace writes and syzbot has found
a way to exploit this [1]. Also as far as I'm reading the code
the filesystem remount code was protected from racing writes in the
legacy mount path by the mount's MNT_READONLY flag so this is relatively
new problem. It is actually fairly easy to protect remount read-write
from racing writes using sb->s_readonly_remount flag so let's just do
that instead of having to workaround these races in the filesystem code.
Signed-off-by: Jan Kara <jack@suse.cz>
Message-Id: <20230615113848.8439-1-jack@suse.cz> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug is caused by the fact that usbnet trusts the bulk endpoint
addresses its probe routine receives in the driver_info structure, and
it does not check to see that these endpoints actually exist and have
the expected type and directions.
The fix is simply to add such a check.
Reported-and-tested-by: syzbot+63ee658b9a100ffadbe2@syzkaller.appspotmail.com Closes: https://lore.kernel.org/linux-usb/000000000000a56e9105d0cec021@google.com/ Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/ea152b6d-44df-4f8a-95c6-4db51143dcc1@rowland.harvard.edu Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
l2cap_sock_release(sk) frees sk. However, sk's children are still alive
and point to the already free'd sk's address.
To fix this, l2cap_sock_release(sk) also cleans sk's children.
==================================================================
BUG: KASAN: use-after-free in l2cap_sock_ready_cb+0xb7/0x100 net/bluetooth/l2cap_sock.c:1650
Read of size 8 at addr ffff888104617aa8 by task kworker/u3:0/276
The buggy address belongs to the object at ffff888104617800
which belongs to the cache kmalloc-1k of size 1024
The buggy address is located 680 bytes inside of
1024-byte region [ffff888104617800, ffff888104617c00)
Ack: This bug is found by FuzzBT with a modified Syzkaller. Other
contributors are Ruoyu Wu and Hui Peng. Signed-off-by: Sungwoo Kim <iam@sung-woo.kim> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 20ea1e7d13c1 ("file: always lock position for
FMODE_ATOMIC_POS") we ended up always taking the file pos lock, because
pidfd_getfd() could get a reference to the file even when it didn't have
an elevated file count due to threading of other sharing cases.
But Mateusz Guzik reports that the extra locking is actually measurable,
so let's re-introduce the optimization, and only force the locking for
directory traversal.
Directories need the lock for correctness reasons, while regular files
only need it for "POSIX semantics". Since pidfd_getfd() is about
debuggers etc special things that are _way_ outside of POSIX, we can
relax the rules for that case.
The root cause is the same as commit 436901649731 ("bpf: cpumap: Fix memory
leak in cpu_map_update_elem"). The kthread is stopped prematurely by
kthread_stop() in cpu_map_kthread_stop(), and kthread() doesn't call
cpu_map_kthread_run() at all but XDP program has already queued some
frames or skbs into ptr_ring. So when __cpu_map_ring_cleanup() checks
the ptr_ring, it will find it was not emptied and report a warning.
An alternative fix is to use __cpu_map_ring_cleanup() to drop these
pending frames or skbs when kthread_stop() returns -EINTR, but it may
confuse the user, because these frames or skbs have been handled
correctly by XDP program. So instead of dropping these frames or skbs,
just make sure the per-cpu kthread is running before
__cpu_map_entry_alloc() returns.
After apply the fix, the error handle for kthread_stop() will be
unnecessary because it will always return 0, so just remove it.
Fixes: 6710e1126934 ("bpf: introduce new bpf cpu map type BPF_MAP_TYPE_CPUMAP") Signed-off-by: Hou Tao <houtao1@huawei.com> Reviewed-by: Pu Lehui <pulehui@huawei.com> Acked-by: Jesper Dangaard Brouer <hawk@kernel.org> Link: https://lore.kernel.org/r/20230729095107.1722450-2-houtao@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
O_TMPFILE is actually __O_TMPFILE|O_DIRECTORY. This means that the old
fast-path check for RESOLVE_CACHED would reject all users passing
O_DIRECTORY with -EAGAIN, when in fact the intended test was to check
for __O_TMPFILE.
We received report [1] of kernel crash, which is caused by
using nesting protection without disabled preemption.
The bpf_event_output can be called by programs executed by
bpf_prog_run_array_cg function that disabled migration but
keeps preemption enabled.
This can cause task to be preempted by another one inside the
nesting protection and lead eventually to two tasks using same
perf_sample_data buffer and cause crashes like:
Due to rbd_try_acquire_lock() effectively swallowing all but
EBLOCKLISTED error from rbd_try_lock() ("request lock anyway") and
rbd_request_lock() returning ETIMEDOUT error not only for an actual
notify timeout but also when the lock owner doesn't respond, a busy
loop inside of rbd_acquire_lock() between rbd_try_acquire_lock() and
rbd_request_lock() is possible.
Requesting the lock on EBUSY error (returned by get_lock_owner_info()
if an incompatible lock or invalid lock owner is detected) makes very
little sense. The same goes for ETIMEDOUT error (might pop up pretty
much anywhere if osd_request_timeout option is set) and many others.
Just fail I/O requests on rbd_dev->acquiring_list immediately on any
error from rbd_try_lock().
Cc: stable@vger.kernel.org # 588159009d5b: rbd: retrieve and check lock owner twice before blocklisting Cc: stable@vger.kernel.org Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On DBDC devices the first (internal) phy is only capable of using
2.4 GHz band, and the 5 GHz band is exposed via a separate phy object,
so avoid the false advertising.
Reported-by: Rani Hod <rani.hod@gmail.com> Closes: https://github.com/openwrt/openwrt/pull/12361 Fixes: 7660a1bd0c22 ("mt76: mt7615: register ext_phy if DBDC is detected") Cc: stable@vger.kernel.org Signed-off-by: Paul Fertser <fercerpav@gmail.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230605073408.8699-1-fercerpav@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 66b2c338adce initializes the "sk_uid" field in the protocol socket
(struct sock) from the "/dev/tapX" device node's owner UID. Per original
commit 86741ec25462 ("net: core: Add a UID field to struct sock.",
2016-11-04), that's wrong: the idea is to cache the UID of the userspace
process that creates the socket. Commit 86741ec25462 mentions socket() and
accept(); with "tap", the action that creates the socket is
open("/dev/tapX").
Therefore the device node's owner UID is irrelevant. In most cases,
"/dev/tapX" will be owned by root, so in practice, commit 66b2c338adce has
no observable effect:
- before, "sk_uid" would be zero, due to undefined behavior
(CVE-2023-1076),
- after, "sk_uid" would be zero, due to "/dev/tapX" being owned by root.
What matters is the (fs)UID of the process performing the open(), so cache
that in "sk_uid".
Cc: Eric Dumazet <edumazet@google.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Pietro Borrello <borrello@diag.uniroma1.it> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Fixes: 66b2c338adce ("tap: tap_open(): correctly initialize socket uid")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2173435 Signed-off-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a096ccca6e50 initializes the "sk_uid" field in the protocol socket
(struct sock) from the "/dev/net/tun" device node's owner UID. Per
original commit 86741ec25462 ("net: core: Add a UID field to struct
sock.", 2016-11-04), that's wrong: the idea is to cache the UID of the
userspace process that creates the socket. Commit 86741ec25462 mentions
socket() and accept(); with "tun", the action that creates the socket is
open("/dev/net/tun").
Therefore the device node's owner UID is irrelevant. In most cases,
"/dev/net/tun" will be owned by root, so in practice, commit a096ccca6e50
has no observable effect:
- before, "sk_uid" would be zero, due to undefined behavior
(CVE-2023-1076),
- after, "sk_uid" would be zero, due to "/dev/net/tun" being owned by root.
What matters is the (fs)UID of the process performing the open(), so cache
that in "sk_uid".
Cc: Eric Dumazet <edumazet@google.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: Pietro Borrello <borrello@diag.uniroma1.it> Cc: netdev@vger.kernel.org Cc: stable@vger.kernel.org Fixes: a096ccca6e50 ("tun: tun_chr_open(): correctly initialize socket uid")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2173435 Signed-off-by: Laszlo Ersek <lersek@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is incorrect to calculate number of OOB bytes for ECC engine using
some "already known" ECC step size (1024 bytes here). Number of such
bytes for ECC engine must be whole OOB except 2 bytes for bad block
marker, while proper ECC step size and strength will be selected by
ECC logic.
tx58cxgxsxraix_ecc_get_status() is using on-stack buffer
for SPINAND_GET_FEATURE_OP() output. It is not suitable
for DMA needs of spi-mem.
Fix this by using the spi-mem operations dedicated buffer
spinand->scratchbuf.
See
spinand->scratchbuf:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/mtd/spinand.h?h=v6.3#n418
spi_mem_check_op():
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/spi/spi-mem.c?h=v6.3#n199
The call stack shown below is a scenario in the Linux 4.19 kernel.
Allocating memory failed where exfat fs use kmalloc_array due to
system memory fragmentation, while the u-disk was inserted without
recognition.
Devices such as u-disk using the exfat file system are pluggable and
may be insert into the system at any time.
However, long-term running systems cannot guarantee the continuity of
physical memory. Therefore, it's necessary to address this issue.
Under certain circumstances, an integer division by 0 which faults, can
leave stale quotient data from a previous division operation on Zen1
microarchitectures.
Do a dummy division 0/1 before returning from the #DE exception handler
in order to avoid any leaks of potentially sensitive data.
Flushing the dirty buffer may take a long time if the cluster is
overloaded or if there is network issue. So we should ping the
MDSs periodically to keep alive, else the MDS will blocklist
the kclient.
The SL-A300, B500/5600, and C700 devices no longer auto-load because of
"usbnet: Remove over-broad module alias from zaurus."
This patch adds IDs for those 3 devices.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217632 Fixes: 16adf5d07987 ("usbnet: Remove over-broad module alias from zaurus.") Signed-off-by: Ross Maynard <bids.7405@bigpond.com> Cc: stable@vger.kernel.org Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/69b5423b-2013-9fc9-9569-58e707d9bafb@bigpond.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the cluster becomes unavailable, ceph_osdc_notify() may hang even
with osd_request_timeout option set because linger_notify_finish_wait()
waits for MWatchNotify NOTIFY_COMPLETE message with no associated OSD
request in flight -- it's completely asynchronous.
Introduce an additional timeout, derived from the specified notify
timeout. While at it, switch both waits to killable which is more
correct.
Cc: stable@vger.kernel.org Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn> Reviewed-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Hyper-V host is queried to get the max transfer size that it supports,
and this value is used to set max_sectors for the synthetic SCSI
controller. However, this max transfer size may be too large for virtual
Fibre Channel devices, which are limited to 512 Kbytes. If a larger
transfer size is used with a vFC device, Hyper-V always returns an error,
and storvsc logs a message like this where the SRB status and SCSI status
are both zero:
Storage devices are free to send RSCNs, e.g. for internal state changes. If
this happens on all connected paths, zfcp risks temporarily losing all
paths at the same time. This has strong requirements on multipath
configuration such as "no_path_retry queue".
Avoid such situations by deferring fc_rport blocking until after the ADISC
response, when any actual state change of the remote port became clear.
The already existing port recovery triggers explicitly block the fc_rport.
The triggers are: on ADISC reject or timeout (typical cable pull case), and
on ADISC indicating that the remote port has changed its WWPN or
the port is meanwhile no longer open.
As a side effect, this also removes a confusing direct function call to
another work item function zfcp_scsi_rport_work() instead of scheduling
that other work item. It was probably done that way to have the rport block
side effect immediate and synchronous to the caller.
Fixes: a2fa0aede07c ("[SCSI] zfcp: Block FC transport rports early on errors") Cc: stable@vger.kernel.org #v2.6.30+ Reviewed-by: Benjamin Block <bblock@linux.ibm.com> Reviewed-by: Fedor Loshakov <loshakov@linux.ibm.com> Signed-off-by: Steffen Maier <maier@linux.ibm.com> Link: https://lore.kernel.org/r/20230724145156.3920244-1-maier@linux.ibm.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever tcpm_new() reclaims an old entry, tcpm_suck_dst()
would overwrite data that could be read from tcp_fastopen_cache_get()
or tcp_metrics_fill_info().
We need to acquire fastopen_seqlock to maintain consistency.
For newly allocated objects, tcpm_new() can switch to kzalloc()
to avoid an extra fastopen_seqlock acquisition.
Fixes: 1fe4c481ba63 ("net-tcp: Fast Open client - cookie cache") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Yuchung Cheng <ycheng@google.com> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20230802131500.1478140-7-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Instead of changing write_pnet() and read_pnet() and potentially
hurt performance, add the needed READ_ONCE()/WRITE_ONCE()
in tm_net() and tcpm_new().
Fixes: 849e8a0ca8d5 ("tcp_metrics: Add a field tcpm_net and verify it matches on lookup") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20230802131500.1478140-6-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Because v4 and v6 families use separate inetpeer trees (respectively
net->ipv4.peers and net->ipv6.peers), inetpeer_addr_cmp(a, b) assumes
a & b share the same family.
tcp_metrics use a common hash table, where entries can have different
families.
We must therefore make sure to not call inetpeer_addr_cmp()
if the families do not match.
Fixes: d39d14ffa24c ("net: Add helper function to compare inetpeer addresses") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com> Link: https://lore.kernel.org/r/20230802131500.1478140-2-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When both supported and previous version have the same major version,
and the firmwares are missing, the driver ends in a loop requesting the
same (previous) version over and over again:
[ 76.327413] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
[ 76.339802] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.352162] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.364502] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.376848] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.389183] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.401522] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.413860] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
[ 76.426199] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.0.img firmware, fall-back to previous 4.0 version
...
Fix this by inverting the check to that we aren't yet at the previous
version, and also check the minor version.
This also catches the case where both versions are the same, as it was
after commit bb5dbf2cc64d ("net: marvell: prestera: add firmware v4.0
support").
With this fix applied:
[ 88.499622] Prestera DX 0000:01:00.0: missing latest mrvl/prestera/mvsw_prestera_fw-v4.1.img firmware, fall-back to previous 4.0 version
[ 88.511995] Prestera DX 0000:01:00.0: failed to request previous firmware: mrvl/prestera/mvsw_prestera_fw-v4.0.img
[ 88.522403] Prestera DX: probe of 0000:01:00.0 failed with error -2
In the cited commit, new type of FS_TYPE_PRIO_CHAINS fs_prio was added
to support multiple parallel namespaces for multi-chains. And we skip
all the flow tables under the fs_node of this type unconditionally,
when searching for the next or previous flow table to connect for a
new table.
As this search function is also used for find new root table when the
old one is being deleted, it will skip the entire FS_TYPE_PRIO_CHAINS
fs_node next to the old root. However, new root table should be chosen
from it if there is any table in it. Fix it by skipping only the flow
tables in the same FS_TYPE_PRIO_CHAINS fs_node when finding the
closest FT for a fs_node.
Besides, complete the connecting from FTs of previous priority of prio
because there should be multiple prevs after this fs_prio type is
introduced. And also the next FT should be chosen from the first flow
table next to the prio in the same FS_TYPE_PRIO_CHAINS fs_prio, if
this prio is the first child.
Fixes: 328edb499f99 ("net/mlx5: Split FDB fast path prio to multiple namespaces") Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Reviewed-by: Paul Blakey <paulb@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/7a95754df479e722038996c97c97b062b372591f.1690803944.git.leonro@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As find_closest_ft_recursive is called to find the closest FT, the
first parameter of find_closest_ft can be changed from fs_prio to
fs_node. Thus this function is extended to find the closest FT for the
nodes of any type, not only prios, but also the sub namespaces.
The nexthop code expects a 31 bit hash, such as what is returned by
fib_multipath_hash() and rt6_multipath_hash(). Passing the 32 bit hash
returned by skb_get_hash() can lead to problems related to the fact that
'int hash' is a negative number when the MSB is set.
In the case of hash threshold nexthop groups, nexthop_select_path_hthr()
will disproportionately select the first nexthop group entry. In the case
of resilient nexthop groups, nexthop_select_path_res() may do an out of
bounds access in nh_buckets[], for example:
hash = -912054133
num_nh_buckets = 2
bucket_index = 65535
Fix this problem by ensuring the MSB of hash is 0 using a right shift - the
same approach used in fib_multipath_hash() and rt6_multipath_hash().
Fixes: 1274e1cc4226 ("vxlan: ecmp support for mac fdb entries") Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When setup a vlan device on dev pim6reg, DAD ns packet may sent on reg_vif_xmit().
reg_vif_xmit()
ip6mr_cache_report()
skb_push(skb, -skb_network_offset(pkt));//skb_network_offset(pkt) is 4
And skb_push declared as:
void *skb_push(struct sk_buff *skb, unsigned int len);
skb->data -= len;
//0xffff88805f86a84c - 0xfffffffc = 0xffff887f5f86a850
skb->data is set to 0xffff887f5f86a850, which is invalid mem addr, lead to skb_push() fails.
Fixes: 14fb64e1f449 ("[IPV6] MROUTE: Support PIM-SM (SSM).") Signed-off-by: Yue Haibing <yuehaibing@huawei.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
dev_close() and dev_open() are issued to change the interface state to DOWN
or UP (dev->flags IFF_UP). When the netdev is set DOWN it loses e.g its
Ipv6 addresses and routes. We don't want this in cases of device recovery
(triggered by hardware or software) or when the qeth device is set
offline.
Setting a qeth device offline or online and device recovery actions call
netif_device_detach() and/or netif_device_attach(). That will reset or
set the LOWER_UP indication i.e. change the dev->state Bit
__LINK_STATE_PRESENT. That is enough to e.g. cause bond failovers, and
still preserves the interface settings that are handled by the network
stack.
Don't call dev_open() nor dev_close() from the qeth device driver. Let the
network stack handle this.
Fixes: d4560150cb47 ("s390/qeth: call dev_close() during recovery") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The dcbnl_bcn_setcfg uses erroneous policy to parse tb[DCB_ATTR_BCN],
which is introduced in commit 859ee3c43812 ("DCB: Add support for DCB
BCN"). Please see the comment in below code
static int dcbnl_bcn_setcfg(...)
{
...
ret = nla_parse_nested_deprecated(..., dcbnl_pfc_up_nest, .. )
// !!! dcbnl_pfc_up_nest for attributes
// DCB_PFC_UP_ATTR_0 to DCB_PFC_UP_ATTR_ALL in enum dcbnl_pfc_up_attrs
...
for (i = DCB_BCN_ATTR_RP_0; i <= DCB_BCN_ATTR_RP_7; i++) {
// !!! DCB_BCN_ATTR_RP_0 to DCB_BCN_ATTR_RP_7 in enum dcbnl_bcn_attrs
...
value_byte = nla_get_u8(data[i]);
...
}
...
for (i = DCB_BCN_ATTR_BCNA_0; i <= DCB_BCN_ATTR_RI; i++) {
// !!! DCB_BCN_ATTR_BCNA_0 to DCB_BCN_ATTR_RI in enum dcbnl_bcn_attrs
...
value_int = nla_get_u32(data[i]);
...
}
...
}
That is, the nla_parse_nested_deprecated uses dcbnl_pfc_up_nest
attributes to parse nlattr defined in dcbnl_pfc_up_attrs. But the
following access code fetch each nlattr as dcbnl_bcn_attrs attributes.
By looking up the associated nla_policy for dcbnl_bcn_attrs. We can find
the beginning part of these two policies are "same".
Therefore, the current code is buggy and this
nla_parse_nested_deprecated could overflow the dcbnl_pfc_up_nest and use
the adjacent nla_policy to parse attributes from DCB_BCN_ATTR_BCNA_0.
Hence use the correct policy dcbnl_bcn_nest to parse the nested
tb[DCB_ATTR_BCN] TLV.
Fixes: 859ee3c43812 ("DCB: Add support for DCB BCN") Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230801013248.87240-1-linma@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
As documented in acd7aaf51b20 ("netsec: ignore 'phy-mode' device
property on ACPI systems") the SocioNext SynQuacer platform ships with
firmware defining the PHY mode as RGMII even though the physical
configuration of the PHY is for TX and RX delays. Since bbc4d71d63549bc
("net: phy: realtek: fix rtl8211e rx/tx delay config") this has caused
misconfiguration of the PHY, rendering the network unusable.
This was worked around for ACPI by ignoring the phy-mode property but
the system is also used with DT. For DT instead if we're running on a
SynQuacer force a working PHY mode, as well as the standard EDK2
firmware with DT there are also some of these systems that use u-boot
and might not initialise the PHY if not netbooting. Newer firmware
imagaes for at least EDK2 are available from Linaro so print a warning
when doing this.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver") Signed-off-by: Mark Brown <broonie@kernel.org> Acked-by: Ard Biesheuvel <ardb@kernel.org> Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20230731-synquacer-net-v3-1-944be5f06428@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
in korina_probe(), the return value of clk_prepare_enable()
should be checked since it might fail. we can use
devm_clk_get_optional_enabled() instead of devm_clk_get_optional()
and clk_prepare_enable() to automatically handle the error.
Fixes: e4cd854ec487 ("net: korina: Get mdio input clock via common clock framework") Signed-off-by: Yuanjun Gong <ruc_gongyuanjun@163.com> Link: https://lore.kernel.org/r/20230731090535.21416-1-ruc_gongyuanjun@163.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Most kernel functions return negative error codes but some irq functions
return zero on error. In this code irq_of_parse_and_map(), returns zero
and platform_get_irq() returns negative error codes. We need to handle
both cases appropriately.
Fixes: 8425c41d1ef7 ("net: ll_temac: Extend support to non-device-tree platforms") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Acked-by: Esben Haabendal <esben@geanix.com> Reviewed-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Harini Katakam <harini.katakam@amd.com> Link: https://lore.kernel.org/r/3d0aef75-06e0-45a5-a2a6-2cc4738d4143@moroto.mountain Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
dev_err() can be replace with dev_err_probe() which will check if error
code is -EPROBE_DEFER.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: ef45e8400f5b ("net: ll_temac: fix error checking of irq_of_parse_and_map()") Signed-off-by: Sasha Levin <sashal@kernel.org>
Disabling preemption in sock_map_sk_acquire conflicts with GFP_ATOMIC
allocation later in sk_psock_init_link on PREEMPT_RT kernels, since
GFP_ATOMIC might sleep on RT (see bpf: Make BPF and PREEMPT_RT co-exist
patchset notes for details).
This causes calling bpf_map_update_elem on BPF_MAP_TYPE_SOCKMAP maps to
BUG (sleeping function called from invalid context) on RT kernels.
preempt_disable was introduced together with lock_sk and rcu_read_lock
in commit 99ba2b5aba24e ("bpf: sockhash, disallow bpf_tcp_close and update
in parallel"), probably to match disabled migration of BPF programs, and
is no longer necessary.
Remove preempt_disable to fix BUG in sock_map_update_common on RT.
When route4_change() is called on an existing filter, the whole
tcf_result struct is always copied into the new instance of the filter.
This causes a problem when updating a filter bound to a class,
as tcf_unbind_filter() is always called on the old instance in the
success path, decreasing filter_cnt of the still referenced class
and allowing it to be deleted, leading to a use-after-free.
Fix this by no longer copying the tcf_result struct from the old filter.
Fixes: 1109c00547fc ("net: sched: RCU cls_route") Reported-by: valis <sec@valis.email> Reported-by: Bing-Jhong Billy Jheng <billy@starlabs.sg> Signed-off-by: valis <sec@valis.email> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Victor Nogueira <victor@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: M A Ramdhan <ramdhan@starlabs.sg> Link: https://lore.kernel.org/r/20230729123202.72406-4-jhs@mojatatu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When fw_change() is called on an existing filter, the whole
tcf_result struct is always copied into the new instance of the filter.
This causes a problem when updating a filter bound to a class,
as tcf_unbind_filter() is always called on the old instance in the
success path, decreasing filter_cnt of the still referenced class
and allowing it to be deleted, leading to a use-after-free.
Fix this by no longer copying the tcf_result struct from the old filter.
Fixes: e35a8ee5993b ("net: sched: fw use RCU") Reported-by: valis <sec@valis.email> Reported-by: Bing-Jhong Billy Jheng <billy@starlabs.sg> Signed-off-by: valis <sec@valis.email> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Victor Nogueira <victor@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: M A Ramdhan <ramdhan@starlabs.sg> Link: https://lore.kernel.org/r/20230729123202.72406-3-jhs@mojatatu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When u32_change() is called on an existing filter, the whole
tcf_result struct is always copied into the new instance of the filter.
This causes a problem when updating a filter bound to a class,
as tcf_unbind_filter() is always called on the old instance in the
success path, decreasing filter_cnt of the still referenced class
and allowing it to be deleted, leading to a use-after-free.
Fix this by no longer copying the tcf_result struct from the old filter.
Fixes: de5df63228fc ("net: sched: cls_u32 changes to knode must appear atomic to readers") Reported-by: valis <sec@valis.email> Reported-by: M A Ramdhan <ramdhan@starlabs.sg> Signed-off-by: valis <sec@valis.email> Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Victor Nogueira <victor@mojatatu.com> Reviewed-by: Pedro Tammela <pctammela@mojatatu.com> Reviewed-by: M A Ramdhan <ramdhan@starlabs.sg> Link: https://lore.kernel.org/r/20230729123202.72406-2-jhs@mojatatu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reason for the warning is twofold. One is due to the kthread
cpu_map_kthread_run() is stopped prematurely. Another one is
__cpu_map_ring_cleanup() doesn't handle skb mode and treats skbs in
ptr_ring as XDP frames.
Prematurely-stopped kthread will be fixed by the preceding patch and
ptr_ring will be empty when __cpu_map_ring_cleanup() is called. But
as the comments in __cpu_map_ring_cleanup() said, handling and freeing
skbs in ptr_ring as well to "catch any broken behaviour gracefully".
Fixes: 11941f8a8536 ("bpf: cpumap: Implement generic cpumap") Signed-off-by: Hou Tao <houtao1@huawei.com> Acked-by: Jesper Dangaard Brouer <hawk@kernel.org> Link: https://lore.kernel.org/r/20230729095107.1722450-3-houtao@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 4cfd5779bd6e ("taprio: Add support for txtime-assist mode") Reported-by: syzkaller <syzkaller@googlegroups.com> Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Co-developed-by: Eric Dumazet <edumazet@google.com> Co-developed-by: Pedro Tammela <pctammela@mojatatu.com> Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In a prior commit I forgot that sk_getsockopt() reads
sk->sk_ll_usec without holding a lock.
Fixes: 0dbffbb5335a ("net: annotate data race around sk_ll_usec") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
sk_getsockopt() runs locklessly, thus we need to annotate the read
of sk->sk_peek_off.
While we are at it, add corresponding annotations to sk_set_peek_off()
and unix_set_peek_off().
Fixes: b9bb53f3836f ("sock: convert sk_peek_offset functions to WRITE_ONCE") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In a prior commit, I forgot to change sk_getsockopt()
when reading sk->sk_rcvbuf locklessly.
Fixes: ebb3b78db7bf ("tcp: annotate sk->sk_rcvbuf lockless reads") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In a prior commit, I forgot to change sk_getsockopt()
when reading sk->sk_sndbuf locklessly.
Fixes: e292f05e0df7 ("tcp: annotate sk->sk_sndbuf lockless reads") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In a prior commit, I forgot to change sk_getsockopt()
when reading sk->sk_rcvlowat locklessly.
Fixes: eac66402d1c3 ("net: annotate sk->sk_rcvlowat lockless reads") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
sk_getsockopt() runs locklessly. This means sk->sk_max_pacing_rate
can be read while other threads are changing its value.
Fixes: 62748f32d501 ("net: introduce SO_MAX_PACING_RATE") Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix this by making caller to provide the context whether it could be in
atomic context flow or not when getting stats from QED driver.
QED driver based on the context provided decide to schedule out or not
when acquiring the PTT BAR window.
We faced the BUG_ON() while getting vport stats, but according to the
code same issue could happen for fcoe and iscsi statistics as well, so
fixing them too.
Fixes: 6c75424612a7 ("qed: Add support for NCSI statistics.") Fixes: 1e128c81290a ("qed: Add support for hardware offloaded FCoE.") Fixes: 2f2b2614e893 ("qed: Provide iSCSI statistics to management") Cc: Sudarsana Kalluru <skalluru@marvell.com> Cc: David Miller <davem@davemloft.net> Cc: Manish Chopra <manishc@marvell.com> Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
As &hc->lock is acquired by both timer _hfcpci_softirq() and hardirq
hfcpci_int(), the timer should disable irq before lock acquisition
otherwise deadlock could happen if the timmer is preemtped by the hadr irq.
A match entry is uniquely identified with an "address" or "path" in the
form of: hashtable ID(12b):bucketid(8b):nodeid(12b).
When creating table match entries all of hash table id, bucket id and
node (match entry id) are needed to be either specified by the user or
reasonable in-kernel defaults are used. The in-kernel default for a table id is
0x800(omnipresent root table); for bucketid it is 0x0. Prior to this fix there
was none for a nodeid i.e. the code assumed that the user passed the correct
nodeid and if the user passes a nodeid of 0 (as Mingi Cho did) then that is what
was used. But nodeid of 0 is reserved for identifying the table. This is not
a problem until we dump. The dump code notices that the nodeid is zero and
assumes it is referencing a table and therefore references table struct
tc_u_hnode instead of what was created i.e match entry struct tc_u_knode.
Ming does an equivalent of:
tc filter add dev dummy0 parent 10: prio 1 handle 0x1000 \
protocol ip u32 match ip src 10.0.0.1/32 classid 10:1 action ok
Essentially specifying a table id 0, bucketid 1 and nodeid of zero
Tableid 0 is remapped to the default of 0x800.
Bucketid 1 is ignored and defaults to 0x00.
Nodeid was assumed to be what Ming passed - 0x000
dumping before fix shows:
~$ tc filter ls dev dummy0 parent 10:
filter protocol ip pref 1 u32 chain 0
filter protocol ip pref 1 u32 chain 0 fh 800: ht divisor 1
filter protocol ip pref 1 u32 chain 0 fh 800: ht divisor -30591
Note that the last line reports a table instead of a match entry
(you can tell this because it says "ht divisor...").
As a result of reporting the wrong data type (misinterpretting of struct
tc_u_knode as being struct tc_u_hnode) the divisor is reported with value
of -30591. Ming identified this as part of the heap address
(physmap_base is 0xffff8880 (-30591 - 1)).
The fix is to ensure that when table entry matches are added and no
nodeid is specified (i.e nodeid == 0) then we get the next available
nodeid from the table's pool.
After the fix, this is what the dump shows:
$ tc filter ls dev dummy0 parent 10:
filter protocol ip pref 1 u32 chain 0
filter protocol ip pref 1 u32 chain 0 fh 800: ht divisor 1
filter protocol ip pref 1 u32 chain 0 fh 800::800 order 2048 key ht 800 bkt 0 flowid 10:1 not_in_hw
match 0a000001/ffffffff at 12
action order 1: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
Reported-by: Mingi Cho <mgcho.minic@gmail.com> Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://lore.kernel.org/r/20230726135151.416917-1-jhs@mojatatu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are totally 9 ndo_bridge_setlink handlers in the current kernel,
which are 1) bnxt_bridge_setlink, 2) be_ndo_bridge_setlink 3)
i40e_ndo_bridge_setlink 4) ice_bridge_setlink 5)
ixgbe_ndo_bridge_setlink 6) mlx5e_bridge_setlink 7)
nfp_net_bridge_setlink 8) qeth_l2_bridge_setlink 9) br_setlink.
By investigating the code, we find that 1-7 parse and use nlattr
IFLA_BRIDGE_MODE but 3 and 4 forget to do the nla_len check. This can
lead to an out-of-attribute read and allow a malformed nlattr (e.g.,
length 0) to be viewed as a 2 byte integer.
To avoid such issues, also for other ndo_bridge_setlink handlers in the
future. This patch adds the nla_len check in rtnl_bridge_setlink and
does an early error return if length mismatches. To make it works, the
break is removed from the parsing for IFLA_BRIDGE_FLAGS to make sure
this nla_for_each_nested iterates every attribute.
Fixes: b1edc14a3fbf ("ice: Implement ice_bridge_getlink and ice_bridge_setlink") Fixes: 51616018dd1b ("i40e: Add support for getlink, setlink ndo ops") Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Lin Ma <linma@zju.edu.cn> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://lore.kernel.org/r/20230726075314.1059224-1-linma@zju.edu.cn Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The nla_for_each_nested parsing in function bpf_sk_storage_diag_alloc
does not check the length of the nested attribute. This can lead to an
out-of-attribute read and allow a malformed nlattr (e.g., length 0) to
be viewed as a 4 byte integer.
This patch adds an additional check when the nlattr is getting counted.
This makes sure the latter nla_get_u32 can access the attributes with
the correct length.
Fixes: 1ed4d92458a9 ("bpf: INET_DIAG support in bpf_sk_storage") Suggested-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Lin Ma <linma@zju.edu.cn> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Link: https://lore.kernel.org/r/20230725023330.422856-1-linma@zju.edu.cn Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
when mlx5_cmd_exec failed in mlx5dr_cmd_create_reformat_ctx, the memory
pointed by 'in' is not released, which will cause memory leak. Move memory
release after mlx5_cmd_exec.
Commit 9fb6c9b3fea1 ("s390/sthyi: add cache to store hypervisor info")
added cache handling for store hypervisor info. This also changed the
possible return code for sthyi_fill().
Instead of only returning a condition code like the sthyi instruction would
do, it can now also return a negative error value (-ENOMEM). handle_styhi()
was not changed accordingly. In case of an error, the negative error value
would incorrectly injected into the guest PSW.
Add proper error handling to prevent this, and update the comment which
describes the possible return values of sthyi_fill().
Fixes: 9fb6c9b3fea1 ("s390/sthyi: add cache to store hypervisor info") Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com> Link: https://lore.kernel.org/r/20230727182939.2050744-1-hca@linux.ibm.com Signed-off-by: Heiko Carstens <hca@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Compiling big-endian targets with Clang produces the diagnostic:
fs/namei.c:2173:13: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
} while (!(has_zero(a, &adata, &constants) | has_zero(b, &bdata, &constants)));
~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
||
fs/namei.c:2173:13: note: cast one or both operands to int to silence this warning
It appears that when has_zero was introduced, two definitions were
produced with different signatures (in particular different return
types).
Looking at the usage in hash_name() in fs/namei.c, I suspect that
has_zero() is meant to be invoked twice per while loop iteration; using
logical-or would not update `bdata` when `a` did not have zeros. So I
think it's preferred to always return an unsigned long rather than a
bool than update the while loop in hash_name() to use a logical-or
rather than bitwise-or.
[ Also changed powerpc version to do the same - Linus ]
For SOMs with an onboard PHY, the RESET_N pull-up resistor is
currently deactivated in the pinmux configuration. When the pinmux
code selects the GPIO function for this pin, with a default direction
of input, this prevents the RESET_N pin from being taken to the proper
3.3V level (deasserted), and this results in the PHY being not
detected since it is held in reset.
Taken from RESET_N pin description in ADIN13000 datasheet:
This pin requires a 1K pull-up resistor to AVDD_3P3.
Activate the pull-up resistor to fix the issue.
Fixes: ade0176dd8a0 ("arm64: dts: imx8mn-var-som: Add Variscite VAR-SOM-MX8MN System on Module") Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Both MMU-600 and MMU-700 have similar errata around TLB invalidation
while both stages of translation are active, which will need some
consideration once nesting support is implemented. For now, though,
it's very easy to make our implicit lack of nesting support explicit
for those cases, so they're less likely to be missed in future.
In certain cases we may want to refuse to allow nested translation even
when both stages are implemented, so let's add an explicit feature for
nesting support which we can control in its own right. For now this
merely serves as documentation, but it means a nice convenient check
will be ready and waiting for the future nesting code.
To work around MMU-700 erratum 2812531 we need to ensure that certain
sequences of commands cannot be issued without an intervening sync. In
practice this falls out of our current command-batching machinery
anyway - each batch only contains a single type of invalidation command,
and ends with a sync. The only exception is when a batch is sufficiently
large to need issuing across multiple command queue slots, wherein the
earlier slots will not contain a sync and thus may in theory interleave
with another batch being issued in parallel to create an affected
sequence across the slot boundary.
Since MMU-700 supports range invalidate commands and thus we will prefer
to use them (which also happens to avoid conditions for other errata),
I'm not entirely sure it's even possible for a single high-level
invalidate call to generate a batch of more than 63 commands, but for
the sake of robustness and documentation, wire up an option to enforce
that a sync is always inserted for every slot issued.
The other aspect is that the relative order of DVM commands cannot be
controlled, so DVM cannot be used. Again that is already the status quo,
but since we have at least defined ARM_SMMU_FEAT_BTM, we can explicitly
disable it for documentation purposes even if it's not wired up anywhere
yet.
MMU-600 versions prior to r1p0 fail to correctly generate a WFE wakeup
event when the command queue transitions fom full to non-full. We can
easily work around this by simply hiding the SEV capability such that we
fall back to polling for space in the queue - since MMU-600 implements
MSIs we wouldn't expect to need SEV for sync completion either, so this
should have little to no impact.
Arm Neoverse-N2 and Cortex-A710 cores are affected by an erratum where
the trbe, under some circumstances, might write upto 64bytes to an
address after the Limit as programmed by the TRBLIMITR_EL1.LIMIT.
This might -
- Corrupt a page in the ring buffer, which may corrupt trace from a
previous session, consumed by userspace.
- Hit the guard page at the end of the vmalloc area and raise a fault.
To keep the handling simpler, we always leave the last page from the
range, which TRBE is allowed to write. This can be achieved by ensuring
that we always have more than a PAGE worth space in the range, while
calculating the LIMIT for TRBE. And then the LIMIT pointer can be
adjusted to leave the PAGE (TRBLIMITR.LIMIT -= PAGE_SIZE), out of the
TRBE range while enabling it. This makes sure that the TRBE will only
write to an area within its allowed limit (i.e, [head-head+size]) and
we do not have to handle address faults within the driver.
Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Leo Yan <leo.yan@linaro.org> Cc: Will Deacon <will@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20211019163153.3692640-5-suzuki.poulose@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arm Neoverse-N2 (#2067961) and Cortex-A710 (#2054223) suffers
from errata, where a TSB (trace synchronization barrier)
fails to flush the trace data completely, when executed from
a trace prohibited region. In Linux we always execute it
after we have moved the PE to trace prohibited region. So,
we can apply the workaround every time a TSB is executed.
The work around is to issue two TSB consecutively.
NOTE: This errata is defined as LOCAL_CPU_ERRATUM, implying
that a late CPU could be blocked from booting if it is the
first CPU that requires the workaround. This is because we
do not allow setting a cpu_hwcaps after the SMP boot. The
other alternative is to use "this_cpu_has_cap()" instead
of the faster system wide check, which may be a bit of an
overhead, given we may have to do this in nvhe KVM host
before a guest entry.
Cc: Will Deacon <will@kernel.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Mike Leach <mike.leach@linaro.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Anshuman Khandual <anshuman.khandual@arm.com> Cc: Marc Zyngier <maz@kernel.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Link: https://lore.kernel.org/r/20211019163153.3692640-4-suzuki.poulose@arm.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever a shutdown is invoked, free irqs only and keep mlx5_irq
synthetic wrapper intact in order to avoid use-after-free on
system shutdown.
for example:
==================================================================
BUG: KASAN: use-after-free in _find_first_bit+0x66/0x80
Read of size 8 at addr ffff88823fc0d318 by task kworker/u192:0/13608
The buggy address belongs to the object at ffff88823fc0d300
which belongs to the cache kmalloc-192 of size 192
The buggy address is located 24 bytes inside of
192-byte region [ffff88823fc0d300, ffff88823fc0d3c0)
Reported-by: Frederick Lawler <fred@cloudflare.com> Link: https://lore.kernel.org/netdev/be5b9271-7507-19c5-ded1-fa78f1980e69@cloudflare.com Signed-off-by: Shay Drory <shayd@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
[hardik: Refer to the irqn member of the mlx5_irq struct, instead of
the msi_map, since we don't have upstream v6.4 commit 235a25fe28de
("net/mlx5: Modify struct mlx5_irq to use struct msi_map")].
[hardik: Refer to the pf_pool member of the mlx5_irq_table struct,
instead of pcif_pool, since we don't have upstream v6.4 commit 8bebfd767909 ("net/mlx5: Improve naming of pci function vectors")]. Signed-off-by: Hardik Garg <hargar@linux.microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous commit made all cqring waits marked as iowait, as a way to
improve performance for short schedules with pending IO. However, for
use cases that have a special reaper thread that does nothing but
wait on events on the ring, this causes a cosmetic issue where we
know have one core marked as being "busy" with 100% iowait.
While this isn't a grave issue, it is confusing to users. Rather than
always mark us as being in iowait, gate setting of current->in_iowait
to 1 by whether or not the waiting task has pending requests.
Due to the way the GDS and SRSO patches flowed into the stable tree, it
was a 50% chance that the merge of the which value GDS and SRSO should
be. Of course, I lost that bet, and chose the opposite of what Linus
chose in commit 64094e7e3118 ("Merge tag 'gds-for-linus-2023-08-01' of
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip")
Fix this up by switching the values to match what is now in Linus's tree
as that is the correct value to mirror.
It is possible that a guest can send a packet that contains a head + 18
slots and yet has a len <= XEN_NETBACK_TX_COPY_LEN. This causes nr_slots
to underflow in xenvif_get_requests() which then causes the subsequent
loop's termination condition to be wrong, causing a buffer overrun of
queue->tx_map_ops.
Rework the code to account for the extra frag_overflow slots.
This is CVE-2023-34319 / XSA-432.
Fixes: ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area") Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com> Reviewed-by: Paul Durrant <paul@xen.org> Reviewed-by: Wei Liu <wei.liu@kernel.org> Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SBPB bit in MSR_IA32_PRED_CMD is supported only after a microcode
patch has been applied so set X86_FEATURE_SBPB only then. Otherwise,
guests would attempt to set that bit and #GP on the MSR write.
While at it, make SMT detection more robust as some guests - depending
on how and what CPUID leafs their report - lead to cpu_smt_control
getting set to CPU_SMT_NOT_SUPPORTED but SRSO_NO should be set for any
guest incarnation where one simply cannot do SMT, for whatever reason.
Set X86_FEATURE_RETHUNK when enabling the SRSO mitigation so that
generated code (e.g., ftrace, static call, eBPF) generates "jmp
__x86_return_thunk" instead of RET.
Add the option to flush IBPB only on VMEXIT in order to protect from
malicious guests but one otherwise trusts the software that runs on the
hypervisor.
Add the option to mitigate using IBPB on a kernel entry. Pull in the
Retbleed alternative so that the IBPB call from there can be used. Also,
if Retbleed mitigation is done using IBPB, the same mitigation can and
must be used here.
projects / linux-stable / log