When at least one CPU runs in nohz_full mode, a dedicated timekeeper CPU
is guaranteed to stay online and to never stop its tick.
Meanwhile on some rare case, the dedicated timekeeper may be running
with interrupts disabled for a while, such as in stop_machine.
If jiffies stop being updated, a nohz_full CPU may end up endlessly
programming the next tick in the past, taking the last jiffies update
monotonic timestamp as a stale base, resulting in an tick storm.
Here is a scenario where it matters:
0) CPU 0 is the timekeeper and CPU 1 a nohz_full CPU.
1) A stop machine callback is queued to execute somewhere.
2) CPU 0 reaches MULTI_STOP_DISABLE_IRQ while CPU 1 is still in
MULTI_STOP_PREPARE. Hence CPU 0 can't do its timekeeping duty. CPU 1
can still take IRQs.
3) CPU 1 receives an IRQ which queues a timer callback one jiffy forward.
4) On IRQ exit, CPU 1 schedules the tick one jiffy forward, taking
last_jiffies_update as a base. But last_jiffies_update hasn't been
updated for 2 jiffies since the timekeeper has interrupts disabled.
5) clockevents_program_event(), which relies on ktime_get(), observes
that the expiration is in the past and therefore programs the min
delta event on the clock.
6) The tick fires immediately, goto 3)
7) Tick storm, the nohz_full CPU is drown and takes ages to reach
MULTI_STOP_DISABLE_IRQ, which is the only way out of this situation.
Solve this with unconditionally updating jiffies if the value is stale
on nohz_full IRQ entry. IRQs and other disturbances are expected to be
rare enough on nohz_full for the unconditional call to ktime_get() to
actually matter.
Reported-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Tested-by: Paul E. McKenney <paulmck@kernel.org> Link: https://lore.kernel.org/r/20211026141055.57358-2-frederic@kernel.org Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tick_nohz_stop_tick() stops the tick and high resolution timers are
disabled, then the clock event device is not put into ONESHOT_STOPPED
mode. This can lead to spurious timer interrupts with some clock event
device drivers that don't shut down entirely after firing.
Eliminate these by putting the device into ONESHOT_STOPPED mode at points
where it is not being reprogrammed. When there are no timers active, then
tick_program_event() with KTIME_MAX can be used to stop the device. When
there is a timer active, the device can be stopped at the next tick (any
new timer added by timers will reprogram the tick).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20220422141446.915024-1-npiggin@gmail.com Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some rare cases, the timekeeper CPU may be delaying its jiffies
update duty for a while. Known causes include:
* The timekeeper is waiting on stop_machine in a MULTI_STOP_DISABLE_IRQ
or MULTI_STOP_RUN state. Disabled interrupts prevent from timekeeping
updates while waiting for the target CPU to complete its
stop_machine() callback.
* The timekeeper vcpu has VMEXIT'ed for a long while due to some overload
on the host.
Detect and fix these situations with emergency timekeeping catchups.
Original-patch-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In blamed commit, I missed that get_dist_table() was allocating
memory using GFP_KERNEL, and acquiring qdisc lock to perform
the swap of newly allocated table with current one.
In this patch, get_dist_table() is allocating memory and
copy user data before we acquire the qdisc lock.
Then we perform swap operations while being protected by the lock.
Note that after this patch netem_change() no longer can do partial changes.
If an error is returned, qdisc conf is left unchanged.
Fixes: 2174a08db80d ("sch_netem: acquire qdisc lock in netem_change()") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Reviewed-by: Simon Horman <simon.horman@corigine.com> Link: https://lore.kernel.org/r/20230622181503.2327695-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
While performing certain power-off sequences, PCI drivers are called to
suspend and resume their underlying devices through PCI PM (power
management) interface. However the hardware does not support PCI PM
suspend/resume operations so system wide suspend/resume leads to bad MFW
(management firmware) state which causes various follow-up errors in driver
when communicating with the device/firmware.
To fix this driver implements PCI PM suspend handler to indicate
unsupported operation to the PCI subsystem explicitly, thus avoiding system
to go into suspended/standby mode.
fnic_clean_pending_aborts() was returning a non-zero value irrespective of
failure or success. This caused the caller of this function to assume that
the device reset had failed, even though it would succeed in most cases. As
a consequence, a successful device reset would escalate to host reset.
If device_add() returns error, the name allocated by dev_set_name() needs
be freed. As the comment of device_add() says, put_device() should be used
to decrease the reference count in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanp().
Fixes: ee959b00c335 ("SCSI: convert struct class_device to struct device") Signed-off-by: Zhu Wang <wangzhu9@huawei.com> Link: https://lore.kernel.org/r/20230803020230.226903-1-wangzhu9@huawei.com Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If device_add() returns error, the name allocated by dev_set_name() needs
be freed. As the comment of device_add() says, put_device() should be used
to give up the reference in the error path. So fix this by calling
put_device(), then the name can be freed in kobject_cleanp().
Fixes: c8806b6c9e82 ("snic: driver for Cisco SCSI HBA") Signed-off-by: Zhu Wang <wangzhu9@huawei.com> Acked-by: Narsimhulu Musini <nmusini@cisco.com> Link: https://lore.kernel.org/r/20230801111421.63651-1-wangzhu9@huawei.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hyper-V provides the ability to connect Fibre Channel LUNs to the host
system and present them in a guest VM as a SCSI device. I/O to the vFC
device is handled by the storvsc driver. The storvsc driver includes a
partial integration with the FC transport implemented in the generic
portion of the Linux SCSI subsystem so that FC attributes can be displayed
in /sys. However, the partial integration means that some aspects of vFC
don't work properly. Unfortunately, a full and correct integration isn't
practical because of limitations in what Hyper-V provides to the guest.
In particular, in the context of Hyper-V storvsc, the FC transport timeout
function fc_eh_timed_out() causes a kernel panic because it can't find the
rport and dereferences a NULL pointer. The original patch that added the
call from storvsc_eh_timed_out() to fc_eh_timed_out() is faulty in this
regard.
In many cases a timeout is due to a transient condition, so the situation
can be improved by just continuing to wait like with other I/O requests
issued by storvsc, and avoiding the guaranteed panic. For a permanent
failure, continuing to wait may result in a hung thread instead of a panic,
which again may be better.
So fix the panic by removing the storvsc call to fc_eh_timed_out(). This
allows storvsc to keep waiting for a response. The change has been tested
by users who experienced a panic in fc_eh_timed_out() due to transient
timeouts, and it solves their problem.
In the future we may want to deprecate the vFC functionality in storvsc
since it can't be fully fixed. But it has current users for whom it is
working well enough, so it should probably stay for a while longer.
Fixes: 3930d7309807 ("scsi: storvsc: use default I/O timeout handler for FC devices") Cc: stable@vger.kernel.org Signed-off-by: Michael Kelley <mikelley@microsoft.com> Link: https://lore.kernel.org/r/1690606764-79669-1-git-send-email-mikelley@microsoft.com Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(lightly modified commit message mostly by Linus Torvalds)
The parsing code for /proc/scsi/scsi is disgusting and broken. We should
have just used 'sscanf()' or something simple like that, but the logic may
actually predate our kernel sscanf library routine for all I know. It
certainly predates both git and BK histories.
And we can't change it to be something sane like that now, because the
string matching at the start is done case-insensitively, and the separator
parsing between numbers isn't done at all, so *any* separator will work,
including a possible terminating NUL character.
This interface is root-only, and entirely for legacy use, so there is
absolutely no point in trying to tighten up the parsing. Because any
separator has traditionally worked, it's entirely possible that people have
used random characters rather than the suggested space.
So don't bother to try to pretty it up, and let's just make a minimal patch
that can be back-ported and we can forget about this whole sorry thing for
another two decades.
Just make it at least not read past the end of the supplied data.
Link: https://lore.kernel.org/linux-scsi/b570f5fe-cb7c-863a-6ed9-f6774c219b88@cybernetics.com/ Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Martin K Petersen <martin.petersen@oracle.com> Cc: James Bottomley <jejb@linux.ibm.com> Cc: Willy Tarreau <w@1wt.eu> Cc: stable@kernel.org Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Signed-off-by: Tony Battersby <tonyb@cybernetics.com> Signed-off-by: Martin K Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We set cache_block_group_error if btrfs_cache_block_group() returns an
error, this is because we could end up not finding space to allocate and
mistakenly return -ENOSPC, and which could then abort the transaction
with the incorrect errno, and in the case of ENOSPC result in a
WARN_ON() that will trip up tests like generic/475.
However there's the case where multiple threads can be racing, one
thread gets the proper error, and the other thread doesn't actually call
btrfs_cache_block_group(), it instead sees ->cached ==
BTRFS_CACHE_ERROR. Again the result is the same, we fail to allocate
our space and return -ENOSPC. Instead we need to set
cache_block_group_error to -EIO in this case to make sure that if we do
not make our allocation we get the appropriate error returned back to
the caller.
CC: stable@vger.kernel.org # 4.14+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[BUG]
Syzbot reported a crash that an ASSERT() got triggered inside
prepare_to_merge().
That ASSERT() makes sure the reloc tree is properly pointed back by its
subvolume tree.
[CAUSE]
After more debugging output, it turns out we had an invalid reloc tree:
BTRFS error (device loop1): reloc tree mismatch, root 8 has no reloc root, expect reloc root key (-8, 132, 8) gen 17
Note the above root key is (TREE_RELOC_OBJECTID, ROOT_ITEM,
QUOTA_TREE_OBJECTID), meaning it's a reloc tree for quota tree.
But reloc trees can only exist for subvolumes, as for non-subvolume
trees, we just COW the involved tree block, no need to create a reloc
tree since those tree blocks won't be shared with other trees.
Only subvolumes tree can share tree blocks with other trees (thus they
have BTRFS_ROOT_SHAREABLE flag).
Thus this new debug output proves my previous assumption that corrupted
on-disk data can trigger that ASSERT().
[FIX]
Besides the dedicated fix and the graceful exit, also let tree-checker to
check such root keys, to make sure reloc trees can only exist for subvolumes.
[BUG]
Syzbot reported a crash that an ASSERT() got triggered inside
prepare_to_merge().
[CAUSE]
The root cause of the triggered ASSERT() is we can have a race between
quota tree creation and relocation.
This leads us to create a duplicated quota tree in the
btrfs_read_fs_root() path, and since it's treated as fs tree, it would
have ROOT_SHAREABLE flag, causing us to create a reloc tree for it.
The bug itself is fixed by a dedicated patch for it, but this already
taught us the ASSERT() is not something straightforward for
developers.
[ENHANCEMENT]
Instead of using an ASSERT(), let's handle it gracefully and output
extra info about the mismatch reloc roots to help debug.
Also with the above ASSERT() removed, we can trigger ASSERT(0)s inside
merge_reloc_roots() later.
Also replace those ASSERT(0)s with WARN_ON()s.
extent_write_cache_pages stops writing pages as soon as nr_to_write hits
zero. That is the right thing for opportunistic writeback, but incorrect
for data integrity writeback, which needs to ensure that no dirty pages
are left in the range. Thus only stop the writeback for WB_SYNC_NONE
if nr_to_write hits 0.
This is a port of write_cache_pages changes in commit 05fe478dd04e
("mm: write_cache_pages integrity fix").
Note that I've only trigger the problem with other changes to the btrfs
writeback code, but this condition seems worthwhile fixing anyway.
CC: stable@vger.kernel.org # 4.14+ Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Reviewed-by: David Sterba <dsterba@suse.com>
[ updated comment ] Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rather than leaving the DMA unmapping of the login buffers to the
login response handler, move this work into the login release functions.
Previously, these functions were only used for freeing the allocated
buffers. This could lead to issues if there are more than one
outstanding login buffer requests, which is possible if a login request
times out.
If a login request times out, then there is another call to send login.
The send login function makes a call to the login buffer release
function. In the past, this freed the buffers but did not DMA unmap.
Therefore, the VIOS could still write to the old login (now freed)
buffer. It is for this reason that it is a good idea to leave the DMA
unmap call to the login buffers release function.
Since the login buffer release functions now handle DMA unmapping,
remove the duplicate DMA unmapping in handle_login_rsp().
Fixes: dff515a3e71d ("ibmvnic: Harden device login requests") Signed-off-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230809221038.51296-3-nnac123@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the LOGIN CRQ fails to send then we must DMA unmap the response
buffer. Previously, if the CRQ failed then the memory was freed without
DMA unmapping.
Fixes: c98d9cc4170d ("ibmvnic: send_login should check for crq errors") Signed-off-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230809221038.51296-2-nnac123@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ensure that all offsets in a login response buffer are within the size
of the allocated response buffer. Any offsets or lengths that surpass
the allocation are likely the result of an incomplete response buffer.
In these cases, a full reset is necessary.
When attempting to login, the ibmvnic device will allocate a response
buffer and pass a reference to the VIOS. The VIOS will then send the
ibmvnic device a LOGIN_RSP CRQ to signal that the buffer has been filled
with data. If the ibmvnic device does not get a response in 20 seconds,
the old buffer is freed and a new login request is sent. With 2
outstanding requests, any LOGIN_RSP CRQ's could be for the older
login request. If this is the case then the login response buffer (which
is for the newer login request) could be incomplete and contain invalid
data. Therefore, we must enforce strict sanity checks on the response
buffer values.
Testing has shown that the `off_rxadd_buff_size` value is filled in last
by the VIOS and will be the smoking gun for these circumstances.
Until VIOS can implement a mechanism for tracking outstanding response
buffers and a method for mapping a LOGIN_RSP CRQ to a particular login
response buffer, the best ibmvnic can do in this situation is perform a
full reset.
Fixes: dff515a3e71d ("ibmvnic: Harden device login requests") Signed-off-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230809221038.51296-1-nnac123@linux.ibm.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device is in error state, marked by the flag
MLX5_DEVICE_STATE_INTERNAL_ERROR, the HW and PCI may not be accessible
and so clock update work should be skipped. Furthermore, such access
through PCI in error state, after calling mlx5_pci_disable_device() can
result in failing to recover from pci errors.
When querying eswitch functions 0 is a valid number of host VFs. After
introducing ARM SRIOV falling through to getting the max value from PCI
results in using the total VFs allowed on the ARM for the host.
Fixes: 86eec50beaf3 ("net/mlx5: Support querying max VFs from device"); Signed-off-by: Daniel Jurgens <danielj@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When 'mcf_edma' is allocated, some space is allocated for a
flexible array at the end of the struct. 'chans' item are allocated, that is
to say 'pdata->dma_channels'.
Then, this number of item is stored in 'mcf_edma->n_chans'.
A few lines later, if 'mcf_edma->n_chans' is 0, then a default value of 64
is set.
This ends to no space allocated by devm_kzalloc() because chans was 0, but
64 items are read and/or written in some not allocated memory.
Change the logic to define a default value before allocating the memory.
A netlink dump callback can return a positive number to signal that more
information needs to be dumped or zero to signal that the dump is
complete. In the second case, the core netlink code will append the
NLMSG_DONE message to the skb in order to indicate to user space that
the dump is complete.
The nexthop bucket dump callback always returns a positive number if
nexthop buckets were filled in the provided skb, even if the dump is
complete. This means that a dump will span at least two recvmsg() calls
as long as nexthop buckets are present. In the last recvmsg() call the
dump callback will not fill in any nexthop buckets because the previous
call indicated that the dump should restart from the last dumped nexthop
ID plus one.
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id 10 group 1 type resilient buckets 2
# strace -e sendto,recvmsg -s 5 ip nexthop bucket
sendto(3, [[{nlmsg_len=24, nlmsg_type=RTM_GETNEXTHOPBUCKET, nlmsg_flags=NLM_F_REQUEST|NLM_F_DUMP, nlmsg_seq=1691396980, nlmsg_pid=0}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], {nlmsg_len=0, nlmsg_type=0 /* NLMSG_??? */, nlmsg_flags=0, nlmsg_seq=0, nlmsg_pid=0}], 152, 0, NULL, 0) = 152
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 128
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[[{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396980, nlmsg_pid=347}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], [{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396980, nlmsg_pid=347}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}]], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 128
id 10 index 0 idle_time 6.66 nhid 1
id 10 index 1 idle_time 6.66 nhid 1
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 20
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[{nlmsg_len=20, nlmsg_type=NLMSG_DONE, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396980, nlmsg_pid=347}, 0], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 20
+++ exited with 0 +++
This behavior is both inefficient and buggy. If the last nexthop to be
dumped had the maximum ID of 0xffffffff, then the dump will restart from
0 (0xffffffff + 1) and never end:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id $((2**32-1)) group 1 type resilient buckets 2
# ip nexthop bucket
id 4294967295 index 0 idle_time 5.55 nhid 1
id 4294967295 index 1 idle_time 5.55 nhid 1
id 4294967295 index 0 idle_time 5.55 nhid 1
id 4294967295 index 1 idle_time 5.55 nhid 1
[...]
Fix by adjusting the dump callback to return zero when the dump is
complete. After the fix only one recvmsg() call is made and the
NLMSG_DONE message is appended to the RTM_NEWNEXTHOPBUCKET responses:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id $((2**32-1)) group 1 type resilient buckets 2
# strace -e sendto,recvmsg -s 5 ip nexthop bucket
sendto(3, [[{nlmsg_len=24, nlmsg_type=RTM_GETNEXTHOPBUCKET, nlmsg_flags=NLM_F_REQUEST|NLM_F_DUMP, nlmsg_seq=1691396737, nlmsg_pid=0}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], {nlmsg_len=0, nlmsg_type=0 /* NLMSG_??? */, nlmsg_flags=0, nlmsg_seq=0, nlmsg_pid=0}], 152, 0, NULL, 0) = 152
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=NULL, iov_len=0}], msg_iovlen=1, msg_controllen=0, msg_flags=MSG_TRUNC}, MSG_PEEK|MSG_TRUNC) = 148
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[{iov_base=[[{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396737, nlmsg_pid=350}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], [{nlmsg_len=64, nlmsg_type=RTM_NEWNEXTHOPBUCKET, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396737, nlmsg_pid=350}, {family=AF_UNSPEC, data="\x00\x00\x00\x00\x00"...}], [{nlmsg_len=20, nlmsg_type=NLMSG_DONE, nlmsg_flags=NLM_F_MULTI, nlmsg_seq=1691396737, nlmsg_pid=350}, 0]], iov_len=32768}], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 148
id 4294967295 index 0 idle_time 6.61 nhid 1
id 4294967295 index 1 idle_time 6.61 nhid 1
+++ exited with 0 +++
Note that if the NLMSG_DONE message cannot be appended because of size
limitations, then another recvmsg() will be needed, but the core netlink
code will not invoke the dump callback and simply reply with a
NLMSG_DONE message since it knows that the callback previously returned
zero.
Add a test that fails before the fix:
# ./fib_nexthops.sh -t basic_res
[...]
TEST: Maximum nexthop ID dump [FAIL]
[...]
And passes after it:
# ./fib_nexthops.sh -t basic_res
[...]
TEST: Maximum nexthop ID dump [ OK ]
[...]
Fixes: 8a1bbabb034d ("nexthop: Add netlink handlers for bucket dump") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20230808075233.3337922-4-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
rtm_dump_nexthop_bucket_nh() is used to dump nexthop buckets belonging
to a specific resilient nexthop group. The function returns a positive
return code (the skb length) upon both success and failure.
The above behavior is problematic. When a complete nexthop bucket dump
is requested, the function that walks the different nexthops treats the
non-zero return code as an error. This causes buckets belonging to
different resilient nexthop groups to be dumped using different buffers
even if they can all fit in the same buffer:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id 10 group 1 type resilient buckets 1
# ip nexthop add id 20 group 1 type resilient buckets 1
# strace -e recvmsg -s 0 ip nexthop bucket
[...]
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[...], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 64
id 10 index 0 idle_time 10.27 nhid 1
[...]
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[...], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 64
id 20 index 0 idle_time 6.44 nhid 1
[...]
Fix by only returning a non-zero return code when an error occurred and
restarting the dump from the bucket index we failed to fill in. This
allows buckets belonging to different resilient nexthop groups to be
dumped using the same buffer:
# ip link add name dummy1 up type dummy
# ip nexthop add id 1 dev dummy1
# ip nexthop add id 10 group 1 type resilient buckets 1
# ip nexthop add id 20 group 1 type resilient buckets 1
# strace -e recvmsg -s 0 ip nexthop bucket
[...]
recvmsg(3, {msg_name={sa_family=AF_NETLINK, nl_pid=0, nl_groups=00000000}, msg_namelen=12, msg_iov=[...], msg_iovlen=1, msg_controllen=0, msg_flags=0}, 0) = 128
id 10 index 0 idle_time 30.21 nhid 1
id 20 index 0 idle_time 26.7 nhid 1
[...]
While this change is more of a performance improvement change than an
actual bug fix, it is a prerequisite for a subsequent patch that does
fix a bug.
Fixes: 8a1bbabb034d ("nexthop: Add netlink handlers for bucket dump") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20230808075233.3337922-3-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A netlink dump callback can return a positive number to signal that more
information needs to be dumped or zero to signal that the dump is
complete. In the second case, the core netlink code will append the
NLMSG_DONE message to the skb in order to indicate to user space that
the dump is complete.
The nexthop dump callback always returns a positive number if nexthops
were filled in the provided skb, even if the dump is complete. This
means that a dump will span at least two recvmsg() calls as long as
nexthops are present. In the last recvmsg() call the dump callback will
not fill in any nexthops because the previous call indicated that the
dump should restart from the last dumped nexthop ID plus one.
This behavior is both inefficient and buggy. If the last nexthop to be
dumped had the maximum ID of 0xffffffff, then the dump will restart from
0 (0xffffffff + 1) and never end:
# ip nexthop add id $((2**32-1)) blackhole
# ip nexthop
id 4294967295 blackhole
id 4294967295 blackhole
[...]
Fix by adjusting the dump callback to return zero when the dump is
complete. After the fix only one recvmsg() call is made and the
NLMSG_DONE message is appended to the RTM_NEWNEXTHOP response:
Note that if the NLMSG_DONE message cannot be appended because of size
limitations, then another recvmsg() will be needed, but the core netlink
code will not invoke the dump callback and simply reply with a
NLMSG_DONE message since it knows that the callback previously returned
zero.
Add a test that fails before the fix:
# ./fib_nexthops.sh -t basic
[...]
TEST: Maximum nexthop ID dump [FAIL]
[...]
And passes after it:
# ./fib_nexthops.sh -t basic
[...]
TEST: Maximum nexthop ID dump [ OK ]
[...]
Fixes: ab84be7e54fc ("net: Initial nexthop code") Reported-by: Petr Machata <petrm@nvidia.com> Closes: https://lore.kernel.org/netdev/87sf91enuf.fsf@nvidia.com/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20230808075233.3337922-2-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some configure flow of hns3 driver, for example, change mtu, it will
disable MAC through firmware before configuration. But firmware disables
MAC asynchronously. The rx traffic may be not stopped in this case.
So fixes it by waiting until mac link is down.
Fixes: a9775bb64aa7 ("net: hns3: fix set and get link ksettings issue") Signed-off-by: Jie Wang <wangjie125@huawei.com> Signed-off-by: Jijie Shao <shaojijie@huawei.com> Reviewed-by: Leon Romanovsky <leonro@nvidia.com> Link: https://lore.kernel.org/r/20230807113452.474224-4-shaojijie@huawei.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the AR8032 part does not support wol, remove related callbacks
from it.
Fixes: 5800091a2061 ("net: phy: at803x: add support for AR8032 PHY") Signed-off-by: Li Yang <leoyang.li@nxp.com> Cc: David Bauer <mail@david-bauer.net> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixing the ODP registration flow to set the iova correctly.
The calculation in ib_umem_num_dma_blocks() function assumes the iova of
the umem is set correctly.
When iova is not set, the calculation in ib_umem_num_dma_blocks() is
equivalent to length/page_size, which is true only when memory is aligned.
For unaligned memory, iova must be set for the ALIGN() in the
ib_umem_num_dma_blocks() to take effect and return a correct value.
mlx5_ib uses ib_umem_num_dma_blocks() to decide the mkey size to use for
the MR. Without this fix, when registering unaligned ODP MR, a wrong
size mkey might be chosen and this might cause the UMR to fail.
Userspace should not be able to trigger DRM_ERROR messages to spam the
logs; especially not through atomic commit parameters which are
completely legitimate for userspace to attempt.
During hotplug remove it is possible that the update counters work
might be pending, and may run after memory has been freed.
Cancel the update counters work before freeing memory.
Fixes: 7724105686e7 ("IB/hfi1: add driver files") Signed-off-by: Douglas Miller <doug.miller@cornelisnetworks.com> Signed-off-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Link: https://lore.kernel.org/r/169099756100.3927190.15284930454106475280.stgit@awfm-02.cornelisnetworks.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change in iavf_fdir_is_dup_fltr adds a spinlock around a loop which
iterates over all filters and looks for a duplicate. The filter can be
removed from list and freed from memory at the same time it's being
compared. All other places where filters are deleted are already
protected with spinlock.
The remaining changes protect adapter->fdir_active_fltr variable so now
all its uses are under a spinlock.
Fixes: 527691bf0682 ("iavf: Support IPv4 Flow Director filters") Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com> Tested-by: Rafal Romanowski <rafal.romanowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230807205011.3129224-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using the syzkaller repro with reduced packet size it was discovered
that XDP_PACKET_HEADROOM is not checked in tun_can_build_skb(),
although pad may be incremented in tun_build_skb(). This may end up
with exceeding the PAGE_SIZE limit in tun_build_skb().
Jason Wang <jasowang@redhat.com> proposed to count XDP_PACKET_HEADROOM
always (e.g. without rcu_access_pointer(tun->xdp_prog)) in
tun_can_build_skb() since there's a window during which XDP program
might be attached between tun_can_build_skb() and tun_build_skb().
BUG_ON(!vlan_info) is triggered in unregister_vlan_dev() with
following testcase:
# ip netns add ns1
# ip netns exec ns1 ip link add bond0 type bond mode 0
# ip netns exec ns1 ip link add bond_slave_1 type veth peer veth2
# ip netns exec ns1 ip link set bond_slave_1 master bond0
# ip netns exec ns1 ip link add link bond_slave_1 name vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link add link bond0 name bond0_vlan10 type vlan id 10 protocol 802.1ad
# ip netns exec ns1 ip link set bond_slave_1 nomaster
# ip netns del ns1
The logical analysis of the problem is as follows:
1. create ETH_P_8021AD protocol vlan10 for bond_slave_1:
register_vlan_dev()
vlan_vid_add()
vlan_info_alloc()
__vlan_vid_add() // add [ETH_P_8021AD, 10] vid to bond_slave_1
2. create ETH_P_8021AD protocol bond0_vlan10 for bond0:
register_vlan_dev()
vlan_vid_add()
__vlan_vid_add()
vlan_add_rx_filter_info()
if (!vlan_hw_filter_capable(dev, proto)) // condition established because bond0 without NETIF_F_HW_VLAN_STAG_FILTER
return 0;
if (netif_device_present(dev))
return dev->netdev_ops->ndo_vlan_rx_add_vid(dev, proto, vid); // will be never called
// The slaves of bond0 will not refer to the [ETH_P_8021AD, 10] vid.
3. detach bond_slave_1 from bond0:
__bond_release_one()
vlan_vids_del_by_dev()
list_for_each_entry(vid_info, &vlan_info->vid_list, list)
vlan_vid_del(dev, vid_info->proto, vid_info->vid);
// bond_slave_1 [ETH_P_8021AD, 10] vid will be deleted.
// bond_slave_1->vlan_info will be assigned NULL.
4. delete vlan10 during delete ns1:
default_device_exit_batch()
dev->rtnl_link_ops->dellink() // unregister_vlan_dev() for vlan10
vlan_info = rtnl_dereference(real_dev->vlan_info); // real_dev of vlan10 is bond_slave_1
BUG_ON(!vlan_info); // bond_slave_1->vlan_info is NULL now, bug is triggered!!!
Add S-VLAN tag related features support to bond driver. So the bond driver
will always propagate the VLAN info to its slaves.
Fix a refcount underflow problem reported by syzbot that can happen
when a system is running out of memory. If xp_alloc_tx_descs() fails,
and it can only fail due to not having enough memory, then the error
path is triggered. In this error path, the refcount of the pool is
decremented as it has incremented before. However, the reference to
the pool in the socket was not nulled. This means that when the socket
is closed later, the socket teardown logic will think that there is a
pool attached to the socket and try to decrease the refcount again,
leading to a refcount underflow.
I chose this fix as it involved adding just a single line. Another
option would have been to move xp_get_pool() and the assignment of
xs->pool to after the if-statement and using xs_umem->pool instead of
xs->pool in the whole if-statement resulting in somewhat simpler code,
but this would have led to much more churn in the code base perhaps
making it harder to backport.
Fixes: ba3beec2ec1d ("xsk: Fix possible crash when multiple sockets are created") Reported-by: syzbot+8ada0057e69293a05fd4@syzkaller.appspotmail.com Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com> Link: https://lore.kernel.org/r/20230809142843.13944-1-magnus.karlsson@gmail.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
value changed: 0x0000000000000000 -> 0x0000000020000081
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 19 Comm: ksoftirqd/1 Not tainted 6.4.0-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 05/27/2023
Fixes: 69e3c75f4d54 ("net: TX_RING and packet mmap") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Link: https://lore.kernel.org/r/20230803145600.2937518-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When booting a kernel with CONFIG_MISDN_DSP=y and CONFIG_CFI_CLANG=y,
there is a failure when dsp_cmx_send() is called indirectly from
call_timer_fn():
The function pointer prototype that call_timer_fn() expects is
void (*fn)(struct timer_list *)
whereas dsp_cmx_send() has a parameter type of 'void *', which causes
the control flow integrity checks to fail because the parameter types do
not match.
Change dsp_cmx_send()'s parameter type to be 'struct timer_list' to
match the expected prototype. The argument is unused anyways, so this
has no functional change, aside from avoiding the CFI failure.
Reported-by: kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202308020936.58787e6c-oliver.sang@intel.com Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Sami Tolvanen <samitolvanen@google.com> Reviewed-by: Kees Cook <keescook@chromium.org> Fixes: e313ac12eb13 ("mISDN: Convert timers to use timer_setup()") Link: https://lore.kernel.org/r/20230802-fix-dsp_cmx_send-cfi-failure-v1-1-2f2e79b0178d@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
strp_done is only called when psock->progs.stream_parser is not NULL,
but stream_parser was set to NULL by sk_psock_stop_strp(), called
by sk_psock_drop() earlier. So, strp_done can never be called.
Introduce SK_PSOCK_RX_ENABLED to mark whether there is strp on psock.
Change the condition for calling strp_done from judging whether
stream_parser is set to judging whether this flag is set. This flag is
only set once when strp_init() succeeds, and will never be cleared later.
Fixes: c0d95d3380ee ("bpf, sockmap: Re-evaluate proto ops when psock is removed from sockmap") Signed-off-by: Xu Kuohai <xukuohai@huawei.com> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/r/20230804073740.194770-3-xukuohai@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sock_map_del_link() operates on both SOCKMAP and SOCKHASH, although
both types have member named "progs", the offset of "progs" member in
these two types is different, so "progs" should be accessed with the
real map type.
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface") Signed-off-by: Xu Kuohai <xukuohai@huawei.com> Reviewed-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/r/20230804073740.194770-2-xukuohai@huaweicloud.com Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xdp->frame_sz > PAGE_SIZE check was introduced in commit c8741e2bfe87
("xdp: Allow bpf_xdp_adjust_tail() to grow packet size"). But Jesper
Dangaard Brouer <jbrouer@redhat.com> noted that after introducing the
xdp_init_buff() which all XDP driver use - it's safe to remove this
check. The original intend was to catch cases where XDP drivers have
not been updated to use xdp.frame_sz, but that is not longer a concern
(since xdp_init_buff).
Running the initial syzkaller repro it was discovered that the
contiguous physical memory allocation is used for both xdp paths in
tun_get_user(), e.g. tun_build_skb() and tun_alloc_skb(). It was also
stated by Jesper Dangaard Brouer <jbrouer@redhat.com> that XDP can
work on higher order pages, as long as this is contiguous physical
memory (e.g. a page).
The test checks that filters that match on source or destination MAC
were only hit once. A host can send more than one packet with a given
source or destination MAC, resulting in failures.
Fix by relaxing the success criterion and instead check that the filters
were not hit zero times. Using tc_check_at_least_x_packets() is also an
option, but it is not available in older kernels.
The default timeout for selftests is 45 seconds, but it is not enough
for forwarding selftests which can takes minutes to finish depending on
the number of tests cases:
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# TEST: IGMPv2 report 239.10.10.10 [ OK ]
# TEST: IGMPv2 leave 239.10.10.10 [ OK ]
# TEST: IGMPv3 report 239.10.10.10 is_include [ OK ]
# TEST: IGMPv3 report 239.10.10.10 include -> allow [ OK ]
#
not ok 1 selftests: net/forwarding: bridge_igmp.sh # TIMEOUT 45 seconds
Fix by switching off the timeout and setting it to 0. A similar change
was done for BPF selftests in commit 6fc5916cc256 ("selftests: bpf:
Switch off timeout").
Fixes: 81573b18f26d ("selftests/net/forwarding: add Makefile to install tests") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/8d149f8c-818e-d141-a0ce-a6bae606bc22@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-3-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As explained in [1], the forwarding selftests are meant to be run with
either physical loopbacks or veth pairs. The interfaces are expected to
be specified in a user-provided forwarding.config file or as command
line arguments. By default, this file is not present and the tests fail:
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
[...]
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# Command line is not complete. Try option "help"
# Failed to create netif
not ok 1 selftests: net/forwarding: bridge_igmp.sh # exit=1
[...]
Fix by skipping a test if interfaces are not provided either via the
configuration file or command line arguments.
# make -C tools/testing/selftests TARGETS=net/forwarding run_tests
[...]
TAP version 13
1..102
# timeout set to 45
# selftests: net/forwarding: bridge_igmp.sh
# SKIP: Cannot create interface. Name not specified
ok 1 selftests: net/forwarding: bridge_igmp.sh # SKIP
[1] tools/testing/selftests/net/forwarding/README
Fixes: 81573b18f26d ("selftests/net/forwarding: add Makefile to install tests") Reported-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Closes: https://lore.kernel.org/netdev/856d454e-f83c-20cf-e166-6dc06cbc1543@alu.unizg.hr/ Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-2-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A handful of tests require physical loopbacks to be used instead of veth
pairs. Add a helper that these tests will invoke in order to be skipped
when executed with veth pairs.
Fixes: 64916b57c0b1 ("selftests: forwarding: Add speed and auto-negotiation test") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Tested-by: Mirsad Todorovac <mirsad.todorovac@alu.unizg.hr> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nikolay Aleksandrov <razor@blackwall.org> Link: https://lore.kernel.org/r/20230808141503.4060661-7-idosch@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3bcbc20942db ("selftests/rseq: Play nice with binaries statically
linked against glibc 2.35+") which is now in Linus' tree introduced uses
of __weak but did nothing to ensure that a definition is provided for it
resulting in build failures for the rseq tests:
rseq.c:41:1: error: unknown type name '__weak'
__weak ptrdiff_t __rseq_offset;
^
rseq.c:41:17: error: expected ';' after top level declarator
__weak ptrdiff_t __rseq_offset;
^
;
rseq.c:42:1: error: unknown type name '__weak'
__weak unsigned int __rseq_size;
^
rseq.c:43:1: error: unknown type name '__weak'
__weak unsigned int __rseq_flags;
Fix this by using the definition from tools/include compiler.h.
Fixes: 3bcbc20942db ("selftests/rseq: Play nice with binaries statically linked against glibc 2.35+") Signed-off-by: Mark Brown <broonie@kernel.org>
Message-Id: <20230804-kselftest-rseq-build-v1-1-015830b66aa9@kernel.org> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original commit adding that check tried to protect the kenrel against
a potential invalid NULL pointer access.
However we call nouveau_connector_detect_depth once without a native_mode
set on purpose for non LVDS connectors and this broke DP support in a few
cases.
Cc: Olaf Skibbe <news@kravcenko.com> Cc: Lyude Paul <lyude@redhat.com> Closes: https://gitlab.freedesktop.org/drm/nouveau/-/issues/238 Closes: https://gitlab.freedesktop.org/drm/nouveau/-/issues/245 Fixes: 20a2ce87fbaf8 ("drm/nouveau/dp: check for NULL nv_connector->native_mode") Signed-off-by: Karol Herbst <kherbst@redhat.com> Reviewed-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230805101813.2603989-1-kherbst@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This might confuse users who are not aware of 5-level paging and expect
all userspace addresses to be under the 47-bit border.
So far problem has only been triggered with ASLR disabled, although it
may also occur with ASLR enabled if the layout is randomized in a just
right way.
The problem happens due to custom placement for the VMAs in the VDSO
code: vdso_addr() tries to place them above the stack and checks the
result against TASK_SIZE_MAX, which is wrong. TASK_SIZE_MAX is set to
the 56-bit border on 5-level paging machines. Use DEFAULT_MAP_WINDOW
instead.
Fixes: b569bab78d8d ("x86/mm: Prepare to expose larger address space to userspace") Reported-by: Yingcong Wu <yingcong.wu@intel.com> Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/all/20230803151609.22141-1-kirill.shutemov%40linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
provided a fix for the Zen2 VZEROUPPER data corruption bug affecting
a range of CPU models, but the AMD Custom APU 0405 found on SteamDeck
was not listed, although it is clearly affected by the vulnerability.
Add this CPU variant to the Zenbleed erratum list, in order to
unconditionally enable the fallback fix until a proper microcode update
is available.
The assertion added to verify the difference in bits set of the
addresses of srso_untrain_ret_alias() and srso_safe_ret_alias() would fail
to link in LLVM's ld.lld linker with the following error:
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:210: at least one side of
the expression must be absolute
ld.lld: error: ./arch/x86/kernel/vmlinux.lds:211: at least one side of
the expression must be absolute
Use ABSOLUTE to evaluate the expression referring to at least one of the
symbols so that LLD can evaluate the linker script.
Also, add linker version info to the comment about XOR being unsupported
in either ld.bfd or ld.lld until somewhat recently.
Do not transition to SNK_UNATTACHED state when receiving vsafe0v event
while in SNK_HARD_RESET_WAIT_VBUS. Ignore VBUS off events as well as
in some platforms VBUS off can be signalled more than once.
[143515.364753] Requesting mux state 1, usb-role 2, orientation 2
[143515.365520] pending state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_SINK_ON @ 650 ms [rev3 HARD_RESET]
[143515.632281] CC1: 0 -> 0, CC2: 3 -> 0 [state SNK_HARD_RESET_SINK_OFF, polarity 1, disconnected]
[143515.637214] VBUS on
[143515.664985] VBUS off
[143515.664992] state change SNK_HARD_RESET_SINK_OFF -> SNK_HARD_RESET_WAIT_VBUS [rev3 HARD_RESET]
[143515.665564] VBUS VSAFE0V
[143515.665566] state change SNK_HARD_RESET_WAIT_VBUS -> SNK_UNATTACHED [rev3 HARD_RESET]
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() because last_role is same
as current role. This happens since last_role gets initialised
to zero during the probe.
To avoid this, add a new flag initial_detection into struct
usb_conn_info, which prevents bailing out during initial
detection.
Cc: <stable@vger.kernel.org> # 5.4 Fixes: 4602f3bff266 ("usb: common: add USB GPIO based connection detection driver") Signed-off-by: Prashanth K <quic_prashk@quicinc.com> Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/1690880632-12588-1-git-send-email-quic_prashk@quicinc.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If dwc3 is runtime suspended we defer processing the event buffer
until resume, by setting the pending_events flag. Set this flag before
triggering resume to avoid race with the runtime resume callback.
While handling the pending events, in addition to checking the event
buffer we also need to process it. Handle this by explicitly calling
dwc3_thread_interrupt(). Also balance the runtime pm get() operation
that triggered this processing.
Syzbot got KMSAN to complain about access to an uninitialized value in
the alauda subdriver of usb-storage:
BUG: KMSAN: uninit-value in alauda_transport+0x462/0x57f0
drivers/usb/storage/alauda.c:1137
CPU: 0 PID: 12279 Comm: usb-storage Not tainted 5.3.0-rc7+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x191/0x1f0 lib/dump_stack.c:113
kmsan_report+0x13a/0x2b0 mm/kmsan/kmsan_report.c:108
__msan_warning+0x73/0xe0 mm/kmsan/kmsan_instr.c:250
alauda_check_media+0x344/0x3310 drivers/usb/storage/alauda.c:460
The problem is that alauda_check_media() doesn't verify that its USB
transfer succeeded before trying to use the received data. What
should happen if the transfer fails isn't entirely clear, but a
reasonably conservative approach is to pretend that no media is
present.
A similar problem exists in a usb_stor_dbg() call in
alauda_get_media_status(). In this case, when an error occurs the
call is redundant, because usb_stor_ctrl_transfer() already will print
a debugging message.
Finally, unrelated to the uninitialized memory access, is the fact
that alauda_check_media() performs DMA to a buffer on the stack.
Fortunately usb-storage provides a general purpose DMA-able buffer for
uses like this. We'll use it instead.
ASPM Mode is ASPM_MODE_CFG need to judge the value of clkreq_0
to set HIGH or LOW, if the ASPM Mode is ASPM_MODE_REG
always set to HIGH during the initialization.
In binder_init(), the destruction of binder_alloc_shrinker_init() is not
performed in the wrong path, which will cause memory leaks. So this commit
introduces binder_alloc_shrinker_exit() and calls it in the wrong path to
fix that.
Signed-off-by: Qi Zheng <zhengqi.arch@bytedance.com> Acked-by: Carlos Llamas <cmllamas@google.com> Fixes: f2517eb76f1f ("android: binder: Add global lru shrinker to binder") Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20230625154937.64316-1-qi.zheng@linux.dev Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The affected lines were resulting in a NULL pointer dereference on our
platform because the device tree contained the following list of
compatible strings:
Since the driver doesn't declare a compatible string "ti,ina232", the OF
matching succeeds on "ti,ina231". But the I2C device ID info is
populated via the first compatible string, cf. modalias population in
of_i2c_get_board_info(). Since there is no "ina232" entry in the legacy
I2C device ID table either, the struct i2c_device_id *id pointer in the
probe function is NULL.
Fix this by using the already populated type variable instead, which
points to the proper driver data. Since the name is also wanted, add a
generic one to the ina2xx_config table.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk> Fixes: c43a102e67db ("iio: ina2xx: add support for TI INA2xx Power Monitors") Link: https://lore.kernel.org/r/20230619141239.2257392-1-alvin@pqrs.dk Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The struct cros_ec_command contains several integer fields and a
trailing array. An allocation size neglecting the integer fields can
lead to buffer overrun.
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org> Signed-off-by: Yiyuan Guo <yguoaz@gmail.com> Fixes: 974e6f02e27e ("iio: cros_ec_sensors_core: Add common functions for the ChromeOS EC Sensor Hub.") Link: https://lore.kernel.org/r/20230630143719.1513906-1-yguoaz@gmail.com Cc: <Stable@vger.kerenl.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
O_TMPFILE is actually __O_TMPFILE|O_DIRECTORY. This means that the old
check for whether RESOLVE_CACHED can be used would incorrectly think
that O_DIRECTORY could not be used with RESOLVE_CACHED.
sk_assign is failing on an s390x machine running Debian "bookworm" for
2 reasons: legacy server_map definition and uninitialized addrlen in
recvfrom() call.
Fix by adding a new-style server_map definition and dropping addrlen
(recvfrom() allows NULL values for src_addr and addrlen).
Since the test should support tc built without libbpf, build the prog
twice: with the old-style definition and with the new-style definition,
then select the right one at runtime. This could be done at compile
time too, but this would not be cross-compilation friendly.
Insn 180 is a call to 'do_bind'. The call's return value is also the return value
for the program. Since do_bind() returns 0/1, so it is legitimate for compiler to
optimize 'return do_bind(ctx) ? 1 : 0' to 'return do_bind(ctx)'. However, such
optimization breaks verifier as the return value of 'do_bind()' is marked as any
scalar which violates the requirement of prog return value 0/1.
There are two ways to fix this problem, (1) changing 'return 1' in do_bind() to
e.g. 'return 10' so the compiler has to do 'do_bind(ctx) ? 1 :0', or (2)
suggested by Andrii, marking do_bind() with __weak attribute so the compiler
cannot make any assumption on do_bind() return value.
This patch adopted adding __weak approach which is simpler and more resistant
to potential compiler optimizations.
test_align selftest relies on BPF verifier log emitting register states
for specific instructions in expected format. Unfortunately, BPF
verifier precision backtracking log interferes with such expectations.
And instruction on which precision propagation happens sometimes don't
output full expected register states. This does indeed look like
something to be improved in BPF verifier, but is beyond the scope of
this patch set.
So to make test_align a bit more robust, inject few dummy R4 = R5
instructions which capture desired state of R5 and won't have precision
tracking logs on them. This fixes tests until we can improve BPF
verifier output in the presence of precision tracking.
Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/r/20221104163649.121784-7-andrii@kernel.org Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Stable-dep-of: ecdf985d7615 ("bpf: track immediate values written to stack by BPF_ST instruction") Signed-off-by: Pu Lehui <pulehui@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Exploit the property of about-to-be-checkpointed state to be able to
forget all precise markings up to that point even more aggressively. We
now clear all potentially inherited precise markings right before
checkpointing and branching off into child state. If any of children
states require precise knowledge of any SCALAR register, those will be
propagated backwards later on before this state is finalized, preserving
correctness.
There is a single selftests BPF program change, but tremendous one: 25x
reduction in number of verified instructions and states in
trace_virtqueue_add_sgs.
Cilium results are more modest, but happen across wider range of programs.
SELFTESTS RESULTS
=================
$ ./veristat -C -e file,prog,insns,states ~/imprecise-early-results.csv ~/imprecise-aggressive-results.csv | grep -v '+0'
File Program Total insns (A) Total insns (B) Total insns (DIFF) Total states (A) Total states (B) Total states (DIFF)
------------------- ----------------------- --------------- --------------- ------------------ ---------------- ---------------- -------------------
loop6.bpf.linked1.o trace_virtqueue_add_sgs 398057 15114 -382943 (-96.20%) 8717 336 -8381 (-96.15%)
------------------- ----------------------- --------------- --------------- ------------------ ---------------- ---------------- -------------------
Setting reg->precise to true in current state is not necessary from
correctness standpoint, but it does pessimise the whole precision (or
rather "imprecision", because that's what we want to keep as much as
possible) tracking. Why is somewhat subtle and my best attempt to
explain this is recorded in an extensive comment for __mark_chain_precise()
function. Some more careful thinking and code reading is probably required
still to grok this completely, unfortunately. Whiteboarding and a bunch
of extra handwaiving in person would be even more helpful, but is deemed
impractical in Git commit.
Next patch pushes this imprecision property even further, building on top of
the insights described in this patch.
End results are pretty nice, we get reduction in number of total instructions
and states verified due to a better states reuse, as some of the states are now
more generic and permissive due to less unnecessary precise=true requirements.
Slight regression in test_tc_dtime.bpf.linked1.o/ingress_fwdns_prio101
is left for a follow up, there might be some more precision-related bugs
in existing BPF verifier logic.
Stop forcing precise=true for SCALAR registers when BPF program has any
subprograms. Current restriction means that any BPF program, as soon as
it uses subprograms, will end up not getting any of the precision
tracking benefits in reduction of number of verified states.
This patch keeps the fallback mark_all_scalars_precise() behavior if
precise marking has to cross function frames. E.g., if subprogram
requires R1 (first input arg) to be marked precise, ideally we'd need to
backtrack to the parent function and keep marking R1 and its
dependencies as precise. But right now we give up and force all the
SCALARs in any of the current and parent states to be forced to
precise=true. We can lift that restriction in the future.
But this patch fixes two issues identified when trying to enable
precision tracking for subprogs.
First, prevent "escaping" from top-most state in a global subprog. While
with entry-level BPF program we never end up requesting precision for
R1-R5 registers, because R2-R5 are not initialized (and so not readable
in correct BPF program), and R1 is PTR_TO_CTX, not SCALAR, and so is
implicitly precise. With global subprogs, though, it's different, as
global subprog a) can have up to 5 SCALAR input arguments, which might
get marked as precise=true and b) it is validated in isolation from its
main entry BPF program. b) means that we can end up exhausting parent
state chain and still not mark all registers in reg_mask as precise,
which would lead to verifier bug warning.
To handle that, we need to consider two cases. First, if the very first
state is not immediately "checkpointed" (i.e., stored in state lookup
hashtable), it will get correct first_insn_idx and last_insn_idx
instruction set during state checkpointing. As such, this case is
already handled and __mark_chain_precision() already handles that by
just doing nothing when we reach to the very first parent state.
st->parent will be NULL and we'll just stop. Perhaps some extra check
for reg_mask and stack_mask is due here, but this patch doesn't address
that issue.
More problematic second case is when global function's initial state is
immediately checkpointed before we manage to process the very first
instruction. This is happening because when there is a call to global
subprog from the main program the very first subprog's instruction is
marked as pruning point, so before we manage to process first
instruction we have to check and checkpoint state. This patch adds
a special handling for such "empty" state, which is identified by having
st->last_insn_idx set to -1. In such case, we check that we are indeed
validating global subprog, and with some sanity checking we mark input
args as precise if requested.
Note that we also initialize state->first_insn_idx with correct start
insn_idx offset. For main program zero is correct value, but for any
subprog it's quite confusing to not have first_insn_idx set. This
doesn't have any functional impact, but helps with debugging and state
printing. We also explicitly initialize state->last_insns_idx instead of
relying on is_state_visited() to do this with env->prev_insns_idx, which
will be -1 on the very first instruction. This concludes necessary
changes to handle specifically global subprog's precision tracking.
Second identified problem was missed handling of BPF helper functions
that call into subprogs (e.g., bpf_loop and few others). From precision
tracking and backtracking logic's standpoint those are effectively calls
into subprogs and should be called as BPF_PSEUDO_CALL calls.
This patch takes the least intrusive way and just checks against a short
list of current BPF helpers that do call subprogs, encapsulated in
is_callback_calling_function() function. But to prevent accidentally
forgetting to add new BPF helpers to this "list", we also do a sanity
check in __check_func_call, which has to be called for each such special
BPF helper, to validate that BPF helper is indeed recognized as
callback-calling one. This should catch any missed checks in the future.
Adding some special flags to be added in function proto definitions
seemed like an overkill in this case.
With the above changes, it's possible to remove forceful setting of
reg->precise to true in __mark_reg_unknown, which turns on precision
tracking both inside subprogs and entry progs that have subprogs. No
warnings or errors were detected across all the selftests, but also when
validating with veristat against internal Meta BPF objects and Cilium
objects. Further, in some BPF programs there are noticeable reduction in
number of states and instructions validated due to more effective
precision tracking, especially benefiting syncookie test.
During unmount process of nilfs2, nothing holds nilfs_root structure after
nilfs2 detaches its writer in nilfs_detach_log_writer(). Previously,
nilfs_evict_inode() could cause use-after-free read for nilfs_root if
inodes are left in "garbage_list" and released by nilfs_dispose_list at
the end of nilfs_detach_log_writer(), and this bug was fixed by commit 9b5a04ac3ad9 ("nilfs2: fix use-after-free bug of nilfs_root in
nilfs_evict_inode()").
However, it turned out that there is another possibility of UAF in the
call path where mark_inode_dirty_sync() is called from iput():
This can happen after commit 0ae45f63d4ef ("vfs: add support for a
lazytime mount option"), which changed iput() to call
mark_inode_dirty_sync() on its final reference if i_state has I_DIRTY_TIME
flag and i_nlink is non-zero.
This issue appears after commit 28a65b49eb53 ("nilfs2: do not write dirty
data after degenerating to read-only") when using the syzbot reproducer,
but the issue has potentially existed before.
Fix this issue by adding a "purging flag" to the nilfs structure, setting
that flag while disposing the "garbage_list" and checking it in
__nilfs_mark_inode_dirty().
Unlike commit 9b5a04ac3ad9 ("nilfs2: fix use-after-free bug of nilfs_root
in nilfs_evict_inode()"), this patch does not rely on ns_writer to
determine whether to skip operations, so as not to break recovery on
mount. The nilfs_salvage_orphan_logs routine dirties the buffer of
salvaged data before attaching the log writer, so changing
__nilfs_mark_inode_dirty() to skip the operation when ns_writer is NULL
will cause recovery write to fail. The purpose of using the cleanup-only
flag is to allow for narrowing of such conditions.
Link: https://lkml.kernel.org/r/20230728191318.33047-1-konishi.ryusuke@gmail.com Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: syzbot+74db8b3087f293d3a13a@syzkaller.appspotmail.com Closes: https://lkml.kernel.org/r/000000000000b4e906060113fd63@google.com Fixes: 0ae45f63d4ef ("vfs: add support for a lazytime mount option") Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: <stable@vger.kernel.org> # 4.0+ Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the pthread allocation for each array item is based on the size
of a pthread_t pointer and should be the size of the pthread_t structure,
so the allocation is under-allocating the correct size. Fix this by using
the size of each element in the pthreads array.
Static analysis cppcheck reported:
tools/testing/radix-tree/regression1.c:180:2: warning: Size of pointer
'threads' used instead of size of its data. [pointerSize]
Link: https://lkml.kernel.org/r/20230727160930.632674-1-colin.i.king@gmail.com Fixes: 1366c37ed84b ("radix tree test harness") Signed-off-by: Colin Ian King <colin.i.king@gmail.com> Cc: Konstantin Khlebnikov <koct9i@gmail.com> Cc: Matthew Wilcox (Oracle) <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't set predefined degamma curve to cursor plane if the cursor
attribute flag is not set. Applying a degamma curve to the cursor by
default breaks userspace expectation. Checking the flag before
performing any color transformation prevents too dark cursor gamma in
DCN3+ on many Linux desktop environment (KDE Plasma, GNOME,
wlroots-based, etc.) as reported at:
- https://gitlab.freedesktop.org/drm/amd/-/issues/1513
This is the same approach followed by DCN2 drivers where the issue is
not present.
Fixes: 03f54d7d3448 ("drm/amd/display: Add DCN3 DPP") Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1513 Signed-off-by: Melissa Wen <mwen@igalia.com> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Tested-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dma-buf backend is supposed to provide its own vm_ops, but some
implementation just have nothing special to do and leave vm_ops
untouched, probably expecting this field to be zero initialized (this
is the case with the system_heap implementation for instance).
Let's reset vma->vm_ops to NULL to keep things working with these
implementations.
Fixes: 26d3ac3cb04d ("drm/shmem-helpers: Redirect mmap for imported dma-buf") Cc: <stable@vger.kernel.org> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Reported-by: Roman Stratiienko <r.stratiienko@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> Tested-by: Roman Stratiienko <r.stratiienko@gmail.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20230724112610.60974-1-boris.brezillon@collabora.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a lurking bug where Fragment Shader Helper Invocations can't load
from memory. But this is actually required in OpenGL and is causing random
hangs or failures in random shaders.
It is unknown how widespread this issue is, but shaders hitting this can
end up with infinite loops.
We enable those only on all Kepler and newer GPUs where we use our own
Firmware.
Nvidia's firmware provides a way to set a kernelspace controlled list of
mmio registers in the gr space from push buffers via MME macros.
v2: drop code for gm200 and newer.
Cc: Ben Skeggs <bskeggs@redhat.com> Cc: David Airlie <airlied@gmail.com> Cc: nouveau@lists.freedesktop.org Cc: stable@vger.kernel.org # 4.19+ Signed-off-by: Karol Herbst <kherbst@redhat.com> Reviewed-by: Dave Airlie <airlied@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230622152017.2512101-1-kherbst@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Section 2.1 of the Platform Specification [1] states:
Unless otherwise specified by a given I/O device, I/O devices are on
ordering channel 0 (i.e., they are point-to-point strongly ordered).
which is not sufficient to guarantee that a readX() by a hart completes
before a subsequent delay() on the same hart (cf. memory-barriers.txt,
"Kernel I/O barrier effects").
Set the I(nput) bit in __io_ar() to restore the ordering, align inline
comments.
pl330_pause() does not set anything to indicate paused condition which
causes pl330_tx_status() to return DMA_IN_PROGRESS. This breaks 8250
DMA flush after the fix in commit 57e9af7831dc ("serial: 8250_dma: Fix
DMA Rx rearm race"). The function comment for pl330_pause() claims
pause is supported but resume is not which is enough for 8250 DMA flush
to work as long as DMA status reports DMA_PAUSED when appropriate.
Add PAUSED state for descriptor and mark BUSY descriptors with PAUSED
in pl330_pause(). Return DMA_PAUSED from pl330_tx_status() when the
descriptor is PAUSED.
The upcoming (and nearly finalized):
https://datatracker.ietf.org/doc/draft-collink-6man-pio-pflag/
will update the IPv6 RA to include a new flag in the PIO field,
which will serve as a hint to perform DHCPv6-PD.
As we don't want DHCPv6 related logic inside the kernel, this piece of
information needs to be exposed to userspace. The simplest option is to
simply expose the entire PIO through the already existing mechanism.
Even without this new flag, the already existing PIO R (router address)
flag (from RFC6275) cannot AFAICT be handled entirely in kernel,
and provides useful information that should be exposed to userspace
(the router's global address, for use by Mobile IPv6).
Also cc'ing stable@ for inclusion in LTS, as while technically this is
not quite a bugfix, and instead more of a feature, it is absolutely
trivial and the alternative is manually cherrypicking into all Android
Common Kernel trees - and I know Greg will ask for it to be sent in via
LTS instead...
Cc: Jen Linkova <furry@google.com> Cc: Lorenzo Colitti <lorenzo@google.com> Cc: David Ahern <dsahern@gmail.com> Cc: YOSHIFUJI Hideaki / 吉藤英明 <yoshfuji@linux-ipv6.org> Cc: stable@vger.kernel.org Signed-off-by: Maciej Żenczykowski <maze@google.com> Link: https://lore.kernel.org/r/20230807102533.1147559-1-maze@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conversion from big-endian to native is done in a common function
mmc_app_send_scr(). Converting in moxart_transfer_pio() is extra.
Double conversion on a LE system returns an incorrect SCR value,
leads to errors:
mmc0: unrecognised SCR structure version 8
Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver") Signed-off-by: Sergei Antonov <saproj@gmail.com> Cc: Jonas Jensen <jonas.jensen@gmail.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230627120549.2400325-1-saproj@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the allowedips self-test, nodes are inserted into the tree, but it
generated an even amount of nodes, but for checking maximum node depth,
there is of course the root node, which makes the total number
necessarily odd. With two few nodes added, it never triggered the
maximum depth check like it should have. So, add 129 nodes instead of
128 nodes, and do so with a more straightforward scheme, starting with
all the bits set, and shifting over one each time. Then increase the
maximum depth to 129, and choose a better name for that variable to
make it clear that it represents depth as opposed to bits.
Cc: stable@vger.kernel.org Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Link: https://lore.kernel.org/r/20230807132146.2191597-2-Jason@zx2c4.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are multiple smb2_ea_info buffers in FILE_FULL_EA_INFORMATION request
from client. ksmbd find next smb2_ea_info using ->NextEntryOffset of
current smb2_ea_info. ksmbd need to validate buffer length Before
accessing the next ea. ksmbd should check buffer length using buf_len,
not next variable. next is the start offset of current ea that got from
previous ea.
Cc: stable@vger.kernel.org Reported-by: zdi-disclosures@trendmicro.com # ZDI-CAN-21598 Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 2b9b8f3b68ed ("ksmbd: validate command payload size"), except
for SMB2_OPLOCK_BREAK_HE command, the request size of other commands
is not checked, it's not expected. Fix it by add check for request
size of other commands.
Cc: stable@vger.kernel.org Fixes: 2b9b8f3b68ed ("ksmbd: validate command payload size") Acked-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Long Li <leo.lilong@huawei.com> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The decision whether to enable a wake irq during suspend can not be done
based on the runtime PM state directly as a driver may use wake irqs
without implementing runtime PM. Such drivers specifically leave the
state set to the default 'suspended' and the wake irq is thus never
enabled at suspend.
Add a new wake irq flag to track whether a dedicated wake irq has been
enabled at runtime suspend and therefore must not be enabled at system
suspend.
Note that pm_runtime_enabled() can not be used as runtime PM is always
disabled during late suspend.
Fixes: 69728051f5bf ("PM / wakeirq: Fix unbalanced IRQ enable for wakeirq") Cc: 4.16+ <stable@vger.kernel.org> # 4.16+ Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Tony Lindgren <tony@atomide.com> Tested-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the dedicated wake IRQ is level trigger, and it uses the
device's low-power status as the wakeup source, that means if the
device is not in low-power state, the wake IRQ will be triggered
if enabled; For this case, need enable the wake IRQ after running
the device's ->runtime_suspend() which make it enter low-power state.
e.g.
Assume the wake IRQ is a low level trigger type, and the wakeup
signal comes from the low-power status of the device.
The wakeup signal is low level at running time (0), and becomes
high level when the device enters low-power state (runtime_suspend
(1) is called), a wakeup event at (2) make the device exit low-power
state, then the wakeup signal also becomes low level.
if enable the wake IRQ before running runtime_suspend during (0),
a wake IRQ will arise, it causes resume immediately;
it works if enable wake IRQ ( e.g. at (3) or (4)) after running
->runtime_suspend().
This patch introduces a new status WAKE_IRQ_DEDICATED_REVERSE to
optionally support enabling wake IRQ after running ->runtime_suspend().
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 8527beb12087 ("PM: sleep: wakeirq: fix wake irq arming") Signed-off-by: Sasha Levin <sashal@kernel.org>
The soundwire subsystem uses two completion structures that allow
drivers to wait for soundwire device to become enumerated on the bus and
initialised by their drivers, respectively.
The code implementing the signalling is currently broken as it does not
signal all current and future waiters and also uses the wrong
reinitialisation function, which can potentially lead to memory
corruption if there are still waiters on the queue.
Not signalling future waiters specifically breaks sound card probe
deferrals as codec drivers can not tell that the soundwire device is
already attached when being reprobed. Some codec runtime PM
implementations suffer from similar problems as waiting for enumeration
during resume can also timeout despite the device already having been
enumerated.
In typical use cases, the peripheral becomes pm_runtime active as a
result of the ALSA/ASoC framework starting up a DAI. The parent/child
hierarchy guarantees that the manager device will be fully resumed
beforehand.
There is however a corner case where the manager device may become
pm_runtime active, but without ALSA/ASoC requesting any functionality
from the peripherals. In this case, the hardware peripheral device
will report as ATTACHED and its initialization routine will be
executed. If this initialization routine initiates any sort of
deferred processing, there is a possibility that the manager could
suspend without the peripheral suspend sequence being invoked: from
the pm_runtime framework perspective, the peripheral is *already*
suspended.
To avoid such disconnects between hardware state and pm_runtime state,
this patch adds an asynchronous pm_request_resume() upon successful
attach/initialization which will result in the proper resume/suspend
sequence to be followed on the peripheral side.
To allow running rseq and KVM's rseq selftests as statically linked
binaries, initialize the various "trampoline" pointers to point directly
at the expect glibc symbols, and skip the dlysm() lookups if the rseq
size is non-zero, i.e. the binary is statically linked *and* the libc
registered its own rseq.
Define weak versions of the symbols so as not to break linking against
libc versions that don't support rseq in any capacity.
The KVM selftests in particular are often statically linked so that they
can be run on targets with very limited runtime environments, i.e. test
machines.
Fixes: 233e667e1ae3 ("selftests/rseq: Uplift rseq selftests for compatibility with glibc-2.35") Cc: Aaron Lewis <aaronlewis@google.com> Cc: kvm@vger.kernel.org Cc: stable@vger.kernel.org Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20230721223352.2333911-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When checking for libc rseq support in the library constructor, don't
only depend on the symbols presence, check that the registration was
completed.
This targets a scenario where the libc has rseq support but it is not
wired for the current architecture in 'bits/rseq.h', we want to fallback
to our internal registration mechanism.
Signed-off-by: Michael Jeanson <mjeanson@efficios.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Link: https://lore.kernel.org/r/20220614154830.1367382-4-mjeanson@efficios.com
Stable-dep-of: 3bcbc20942db ("selftests/rseq: Play nice with binaries statically linked against glibc 2.35+") Signed-off-by: Sasha Levin <sashal@kernel.org>
When hactive is not aligned to 8 pixels, it is aligned accordingly and
hfront porch needs to be reduced the same amount. Unfortunately the front
porch is set to the difference rather than reducing it. There are some
Samsung TVs which can't cope with a front porch of instead of 70.
altmap->free includes the entire free space from which altmap blocks
can be allocated. So when checking whether the kernel is doing altmap
block free, compute the boundary correctly, otherwise memory hotunplug
can fail.
Fixes: 9ef34630a461 ("powerpc/mm: Fallback to RAM if the altmap is unusable") Signed-off-by: "Aneesh Kumar K.V" <aneesh.kumar@linux.ibm.com> Reviewed-by: David Hildenbrand <david@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://msgid.link/20230724181320.471386-1-aneesh.kumar@linux.ibm.com Signed-off-by: Sasha Levin <sashal@kernel.org>
'op-cs' is copied in 'fun->mchip_number' which is used to access the
'mchip_offsets' and the 'rnb_gpio' arrays.
These arrays have NAND_MAX_CHIPS elements, so the index must be below this
limit.
Fix the sanity check in order to avoid the NAND_MAX_CHIPS value. This
would lead to out-of-bound accesses.
Currently, read/write_page_hwecc() and read/write_page_raw() are not
aligned: there is a mismatch in the OOB bytes which are not
read/written at the same offset in both cases (raw vs. hwecc).
This is a real problem when relying on the presence of the Page
Addresses (PA) when using the NAND chip as a boot device, as the
BootROM expects additional data in the OOB area at specific locations.
Rockchip boot blocks are written per 4 x 512 byte sectors per page.
Each page with boot blocks must have a page address (PA) pointer in OOB
to the next page. Pages are written in a pattern depending on the NAND chip ID.
Generate boot block page address and pattern for hwecc in user space
and copy PA data to/from the already reserved last 4 bytes before ECC
in the chip->oob_poi data layout.
Align the different helpers. This change breaks existing jffs2 users.
Fixes: 058e0e847d54 ("mtd: rawnand: rockchip: NFC driver for RK3308, RK2928 and others") Signed-off-by: Johan Jonker <jbx6244@gmail.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/linux-mtd/5e782c08-862b-51ae-47ff-3299940928ca@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log