In unprivileged Xen guests event handling can cause a deadlock with
Xen console handling. The evtchn_rwlock and the hvc_lock are taken in
opposite sequence in __hvc_poll() and in Xen console IRQ handling.
Normally this is no problem, as the evtchn_rwlock is taken as a reader
in both paths, but as soon as an event channel is being closed, the
lock will be taken as a writer, which will cause read_lock() to block:
read_lock(evtchn_rwlock)
spin_lock(hvc_lock)
write_lock(evtchn_rwlock)
[blocks]
spin_lock(hvc_lock)
[blocks]
read_lock(evtchn_rwlock)
[blocks due to writer waiting,
and not in_interrupt()]
This issue can be avoided by replacing evtchn_rwlock with RCU in
xen_free_irq(). Note that RCU is used only to delay freeing of the
irq_info memory. There is no RCU based dereferencing or replacement of
pointers involved.
In order to avoid potential races between removing the irq_info
reference and handling of interrupts, set the irq_info pointer to NULL
only when freeing its memory. The IRQ itself must be freed at that
time, too, as otherwise the same IRQ number could be allocated again
before handling of the old instance would have been finished.
This is XSA-441 / CVE-2023-34324.
Fixes: 54c9de89895e ("xen/events: add a new "late EOI" evtchn framework") Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Signed-off-by: Juergen Gross <jgross@suse.com> Reviewed-by: Julien Grall <jgrall@amazon.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Back in 2005, Kyle McMartin removed the 16-byte alignment for
ldcw semaphores on PA 2.0 machines (CONFIG_PA20). This broke
spinlocks on pre PA8800 processors. The main symptom was random
faults in mmap'd memory (e.g., gcc compilations, etc).
Unfortunately, the errata for this ldcw change is lost.
The issue is the 16-byte alignment required for ldcw semaphore
instructions can only be reduced to natural alignment when the
ldcw operation can be handled coherently in cache. Only PA8800
and PA8900 processors actually support doing the operation in
cache.
Aligning the spinlock dynamically adds two integer instructions
to each spinlock.
In case immediate MPA request processing fails, the newly
created endpoint unlinks the listening endpoint and is
ready to be dropped. This special case was not handled
correctly by the code handling the later TCP socket close,
causing a NULL dereference crash in siw_cm_work_handler()
when dereferencing a NULL listener. We now also cancel
the useless MPA timeout, if immediate MPA request
processing fails.
This patch furthermore simplifies MPA processing in general:
Scheduling a useless TCP socket read in sk_data_ready() upcall
is now surpressed, if the socket is already moved out of
TCP_ESTABLISHED state.
Fixes: 6c52fdc244b5 ("rdma/siw: connection management") Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com> Link: https://lore.kernel.org/r/20230905145822.446263-1-bmt@zurich.ibm.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since size of 'hdr' pointer and '*hdr' structure is equal on 64-bit
machines issue probably didn't cause any wrong behavior. But anyway,
fixing of typo is required.
Fixes: da0f60df7bd5 ("RDMA/uverbs: Prohibit write() calls with too small buffers") Co-developed-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com> Signed-off-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com> Signed-off-by: Konstantin Meskhidze <konstantin.meskhidze@huawei.com> Link: https://lore.kernel.org/r/20230905103258.1738246-1-konstantin.meskhidze@huawei.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following compilation error is false alarm as RDMA devices don't
have such large amount of ports to actually cause to format truncation.
drivers/infiniband/core/cma_configfs.c: In function ‘make_cma_ports’:
drivers/infiniband/core/cma_configfs.c:223:57: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
223 | snprintf(port_str, sizeof(port_str), "%u", i + 1);
| ^
drivers/infiniband/core/cma_configfs.c:223:17: note: ‘snprintf’ output between 2 and 11 bytes into a destination of size 10
223 | snprintf(port_str, sizeof(port_str), "%u", i + 1);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[5]: *** [scripts/Makefile.build:243: drivers/infiniband/core/cma_configfs.o] Error 1
Initialize the structure to 0 so that it's fields won't have random
values. For example fields like rec.traffic_class (as well as
rec.flow_label and rec.sl) is used to generate the user AH through:
cma_iboe_join_multicast
cma_make_mc_event
ib_init_ah_from_mcmember
And a random traffic_class causes a random IP DSCP in RoCEv2.
Fixes: b5de0c60cc30 ("RDMA/cma: Fix use after free race in roce multicast join") Signed-off-by: Mark Zhang <markzhang@nvidia.com> Link: https://lore.kernel.org/r/20230927090511.603595-1-markzhang@nvidia.com Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pinctrl_gpio_set_config() expects the GPIO number from the global GPIO
numberspace, not the controller-relative offset, which needs to be added
to the chip base.
In order to be sure that 'buff' is never truncated, its size should be
12, not 11.
When building with W=1, this fixes the following warnings:
drivers/infiniband/hw/mlx4/sysfs.c: In function ‘add_port_entries’:
drivers/infiniband/hw/mlx4/sysfs.c:268:34: error: ‘sprintf’ may write a terminating nul past the end of the destination [-Werror=format-overflow=]
268 | sprintf(buff, "%d", i);
| ^
drivers/infiniband/hw/mlx4/sysfs.c:268:17: note: ‘sprintf’ output between 2 and 12 bytes into a destination of size 11
268 | sprintf(buff, "%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/mlx4/sysfs.c:286:34: error: ‘sprintf’ may write a terminating nul past the end of the destination [-Werror=format-overflow=]
286 | sprintf(buff, "%d", i);
| ^
drivers/infiniband/hw/mlx4/sysfs.c:286:17: note: ‘sprintf’ output between 2 and 12 bytes into a destination of size 11
286 | sprintf(buff, "%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~
Smatch complains that the error path where "action" is invalid leaks
the "ce" allocation:
drivers/of/dynamic.c:935 of_changeset_action()
warn: possible memory leak of 'ce'
Fix this by doing the validation before the allocation.
Note that there is not any actual problem with upstream kernels. All
callers of of_changeset_action() are static inlines with fixed action
values.
Fixes: 914d9d831e61 ("of: dynamic: Refactor action prints to not use "%pOF" inside devtree_lock") Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/r/202309011059.EOdr4im9-lkp@intel.com/ Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/7dfaf999-30ad-491c-9615-fb1138db121c@moroto.mountain Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4dba12881f88 ("dm zoned: support arbitrary number of devices")
made the pointers to additional zoned devices to be stored in a
dynamically allocated dmz->ddev array. However, this array is not freed.
Rename dmz_put_zoned_device to dmz_put_zoned_devices and fix it to
free the dmz->ddev array when cleaning up zoned device information.
Remove NULL assignment for all dmz->ddev elements and just free the
dmz->ddev array instead.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4dba12881f88 ("dm zoned: support arbitrary number of devices") Cc: stable@vger.kernel.org Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: Mike Snitzer <snitzer@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EHL (Elkhart Lake) based platforms provide a OOB (Out of band)
service, which allows to wakup device when the system is in S5 (Soft-Off
state). This OOB service can be enabled/disabled from BIOS settings. When
enabled, the ISH device gets PME wake capability. To enable PME wakeup,
driver also needs to enable ACPI GPE bit.
On resume, BIOS will clear the wakeup bit. So driver need to re-enable it
in resume function to keep the next wakeup capability. But this BIOS
clearing of wakeup bit doesn't decrement internal OS GPE reference count,
so this reenabling on every resume will cause reference count to overflow.
So first disable and reenable ACPI GPE bit using acpi_disable_gpe().
Currently, when hb_interval is changed by users, it won't take effect
until the next expiry of hb timer. As the default value is 30s, users
have to wait up to 30s to wait its hb_interval update to work.
This becomes pretty bad in containers where a much smaller value is
usually set on hb_interval. This patch improves it by resetting the
hb timer immediately once the value of hb_interval is updated by users.
Note that we don't address the already existing 'problem' when sending
a heartbeat 'on demand' if one hb has just been sent(from the timer)
mentioned in:
During the 4-way handshake, the transport's state is set to ACTIVE in
sctp_process_init() when processing INIT_ACK chunk on client or
COOKIE_ECHO chunk on server.
when processing COOKIE_ECHO on 192.168.1.2, as it's in COOKIE_WAIT state,
sctp_sf_do_dupcook_b() is called by sctp_sf_do_5_2_4_dupcook() where it
creates a new association and sets its transport to ACTIVE then updates
to the old association in sctp_assoc_update().
However, in sctp_assoc_update(), it will skip the transport update if it
finds a transport with the same ipaddr already existing in the old asoc,
and this causes the old asoc's transport state not to move to ACTIVE
after the handshake.
This means if DATA retransmission happens at this moment, it won't be able
to enter PF state because of the check 'transport->state == SCTP_ACTIVE'
in sctp_do_8_2_transport_strike().
This patch fixes it by updating the transport in sctp_assoc_update() with
sctp_assoc_add_peer() where it updates the transport state if there is
already a transport with the same ipaddr exists in the old asoc.
This commit fixes poor delayed ACK behavior that can cause poor TCP
latency in a particular boundary condition: when an application makes
a TCP socket write that is an exact multiple of the MSS size.
The problem is that there is painful boundary discontinuity in the
current delayed ACK behavior. With the current delayed ACK behavior,
we have:
(1) If an app reads data when > 1*MSS is unacknowledged, then
tcp_cleanup_rbuf() ACKs immediately because of:
(2) If an app reads all received data, and the packets were < 1*MSS,
and either (a) the app is not ping-pong or (b) we received two
packets < 1*MSS, then tcp_cleanup_rbuf() ACKs immediately beecause
of:
(3) *However*: if an app reads exactly 1*MSS of data,
tcp_cleanup_rbuf() does not send an immediate ACK. This is true
even if the app is not ping-pong and the 1*MSS of data had the PSH
bit set, suggesting the sending application completed an
application write.
Thus if the app is not ping-pong, we have this painful case where
>1*MSS gets an immediate ACK, and <1*MSS gets an immediate ACK, but a
write whose last skb is an exact multiple of 1*MSS can get a 40ms
delayed ACK. This means that any app that transfers data in one
direction and takes care to align write size or packet size with MSS
can suffer this problem. With receive zero copy making 4KB MSS values
more common, it is becoming more common to have application writes
naturally align with MSS, and more applications are likely to
encounter this delayed ACK problem.
The fix in this commit is to refine the delayed ACK heuristics with a
simple check: immediately ACK a received 1*MSS skb with PSH bit set if
the app reads all data. Why? If an skb has a len of exactly 1*MSS and
has the PSH bit set then it is likely the end of an application
write. So more data may not be arriving soon, and yet the data sender
may be waiting for an ACK if cwnd-bound or using TX zero copy. Thus we
set ICSK_ACK_PUSHED in this case so that tcp_cleanup_rbuf() will send
an ACK immediately if the app reads all of the data and is not
ping-pong. Note that this logic is also executed for the case where
len > MSS, but in that case this logic does not matter (and does not
hurt) because tcp_cleanup_rbuf() will always ACK immediately if the
app reads data and there is more than an MSS of unACKed data.
This commit fixes quick-ack counting so that it only considers that a
quick-ack has been provided if we are sending an ACK that newly
acknowledges data.
The code was erroneously using the number of data segments in outgoing
skbs when deciding how many quick-ack credits to remove. This logic
does not make sense, and could cause poor performance in
request-response workloads, like RPC traffic, where requests or
responses can be multi-segment skbs.
When a TCP connection decides to send N quick-acks, that is to
accelerate the cwnd growth of the congestion control module
controlling the remote endpoint of the TCP connection. That quick-ack
decision is purely about the incoming data and outgoing ACKs. It has
nothing to do with the outgoing data or the size of outgoing data.
And in particular, an ACK only serves the intended purpose of allowing
the remote congestion control to grow the congestion window quickly if
the ACK is ACKing or SACKing new data.
The fix is simple: only count packets as serving the goal of the
quickack mechanism if they are ACKing/SACKing new data. We can tell
whether this is the case by checking inet_csk_ack_scheduled(), since
we schedule an ACK exactly when we are ACKing/SACKing new data.
Fixes: fc6415bcb0f5 ("[TCP]: Fix quick-ack decrementing with TSO.") Signed-off-by: Neal Cardwell <ncardwell@google.com> Reviewed-by: Yuchung Cheng <ycheng@google.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20231001151239.1866845-1-ncardwell.sw@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
It seems that tipc_crypto_key_revoke() could be be invoked by
wokequeue tipc_crypto_work_rx() under process context and
timer/rx callback under softirq context, thus the lock acquisition
on &tx->lock seems better use spin_lock_bh() to prevent possible
deadlock.
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
The STM32MP1 keeps clk_rx enabled during suspend, and therefore the
driver does not enable the clock in stm32_dwmac_init() if the device was
suspended. The problem is that this same code runs on STM32 MCUs, which
do disable clk_rx during suspend, causing the clock to never be
re-enabled on resume.
This patch adds a variant flag to indicate that clk_rx remains enabled
during suspend, and uses this to decide whether to enable the clock in
stm32_dwmac_init() if the device was suspended.
This approach fixes this specific bug with limited opportunity for
unintended side-effects, but I have a follow up patch that will refactor
the clock configuration and hopefully make it less error prone.
Fixes: 6528e02cc9ff ("net: ethernet: stmmac: add adaptation for stm32mp157c.") Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Link: https://lore.kernel.org/r/20230927175749.1419774-1-ben.wolsieffer@hefring.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Due to a small omission, the offload_failed flag is missing from ipv4
fibmatch results. Make sure it is set correctly.
The issue can be witnessed using the following commands:
echo "1 1" > /sys/bus/netdevsim/new_device
ip link add dummy1 up type dummy
ip route add 192.0.2.0/24 dev dummy1
echo 1 > /sys/kernel/debug/netdevsim/netdevsim1/fib/fail_route_offload
ip route add 198.51.100.0/24 dev dummy1
ip route
# 192.168.15.0/24 has rt_trap
# 198.51.100.0/24 has rt_offload_failed
ip route get 192.168.15.1 fibmatch
# Result has rt_trap
ip route get 198.51.100.1 fibmatch
# Result differs from the route shown by `ip route`, it is missing
# rt_offload_failed
ip link del dev dummy1
echo 1 > /sys/bus/netdevsim/del_device
Fixes: 36c5100e859d ("IPv4: Add "offload failed" indication to routes") Signed-off-by: Benjamin Poirier <bpoirier@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20230926182730.231208-1-bpoirier@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
nft_rbtree_gc_elem() walks back and removes the end interval element that
comes before the expired element.
There is a small chance that we've cached this element as 'rbe_ge'.
If this happens, we hold and test a pointer that has been queued for
freeing.
It also causes spurious insertion failures:
$ cat test-testcases-sets-0044interval_overlap_0.1/testout.log
Error: Could not process rule: File exists
add element t s { 0 - 2 }
^^^^^^
Failed to insert 0 - 2 given:
table ip t {
set s {
type inet_service
flags interval,timeout
timeout 2s
gc-interval 2s
}
}
The set (rbtree) is empty. The 'failure' doesn't happen on next attempt.
Reason is that when we try to insert, the tree may hold an expired
element that collides with the range we're adding.
While we do evict/erase this element, we can trip over this check:
if (rbe_ge && nft_rbtree_interval_end(rbe_ge) && nft_rbtree_interval_end(new))
return -ENOTEMPTY;
rbe_ge was erased by the synchronous gc, we should not have done this
check. Next attempt won't find it, so retry results in successful
insertion.
Restart in-kernel to avoid such spurious errors.
Such restart are rare, unless userspace intentionally adds very large
numbers of elements with very short timeouts while setting a huge
gc interval.
Even in this case, this cannot loop forever, on each retry an existing
element has been removed.
As the caller is holding the transaction mutex, its impossible
for a second entity to add more expiring elements to the tree.
After this it also becomes feasible to remove the async gc worker
and perform all garbage collection from the commit path.
Fixes: c9e6978e2725 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
In SCTP_CID_INIT processing:
- clear ct->proto.sctp.init[!dir] if ct->proto.sctp.init[dir] &&
ct->proto.sctp.init[!dir]. (Scenario E)
- set ct->proto.sctp.init[dir].
In SCTP_CID_INIT_ACK processing:
- drop it if !ct->proto.sctp.init[!dir] && ct->proto.sctp.vtag[!dir] &&
ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario B, Scenario C)
- drop it if ct->proto.sctp.init[dir] && ct->proto.sctp.init[!dir] &&
ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario A)
In SCTP_CID_COOKIE_ACK processing:
- clear ct->proto.sctp.init[dir] and ct->proto.sctp.init[!dir].
(Scenario D)
Also, it's important to allow the ct state to move forward with cookie_echo
and cookie_ack from the opposite dir for the collision scenarios.
There are also other Scenarios where it should allow the packet through,
addressed by the processing above:
Scenario C: new CT is created by INIT_ACK.
Scenario D: start INIT on the existing ESTABLISHED ct.
Scenario E: start INIT after the old collision on the existing ESTABLISHED
ct.
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
(both side are stopped, then start new connection again in hours)
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 242308742]
In some OVS environments the TCP pseudo header checksum may need to be
recomputed. Currently this is only done when the interface instance is
configured for "Trunk Mode". We found the issue also occurs in some
Kubernetes environments, these environments do not use "Trunk Mode",
therefor the condition is removed.
Performance tests with this change show only a fractional decrease in
throughput (< 0.2%).
Fixes: 7525de2516fb ("ibmveth: Set CHECKSUM_PARTIAL if NULL TCP CSUM.") Signed-off-by: David Wilder <dwilder@us.ibm.com> Reviewed-by: Nick Child <nnac123@linux.ibm.com> Reviewed-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This accidentally returns success, but it should return a negative error
code.
Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Reviewed-by: Roger Quadros <rogerq@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
This issue is caused because usbnet_read_cmd() reads less bytes than requested
(zero byte in the reproducer). In this case, 'buf' is not properly filled.
This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads
less bytes than requested.
Fixes: d0cad871703b ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver") Reported-and-tested-by: syzbot+6966546b78d050bb0b5d@syzkaller.appspotmail.com Closes: https://syzkaller.appspot.com/bug?extid=6966546b78d050bb0b5d Signed-off-by: Shigeru Yoshida <syoshida@redhat.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20230923173549.3284502-1-syoshida@redhat.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Since commit 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:
mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done
This board does not have an EEPROM attached to the switch though.
This problem is well explained by Andrew Lunn:
"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.
The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.
However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.
We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:
bit 15 is:
EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
operation (see EEOp below). Only one EEPROM operation can be
executing at one time so this bit must be zero before setting it to
a one. When the requested EEPROM operation completes this bit will
automatically be cleared to a zero. The transition of this bit from
a one to a zero can be used to generate an interrupt (the EEInt in
Global 1, offset 0x00).
and more interesting is bit 11:
Register Loader Running. This bit is set to one whenever the
register loader is busy executing instructions contained in the
EEPROM."
Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.
Fixes: 23d775f12dcd ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset") Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Fabio Estevam <festevam@denx.de> Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
When device_add() fails, ptp_ocp_dev_release() will be called
after put_device(). Therefore, it seems that the
ptp_ocp_dev_release() before put_device() is redundant.
Fixes: 773bda964921 ("ptp: ocp: Expose various resources on the timecard.") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Reviewed-by: Vadim Feodrenko <vadim.fedorenko@linux.dev> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Including the transhdrlen in length is a problem when the packet is
partially filled (e.g. something like send(MSG_MORE) happened previously)
when appending to an IPv4 or IPv6 packet as we don't want to repeat the
transport header or account for it twice. This can happen under some
circumstances, such as splicing into an L2TP socket.
The symptom observed is a warning in __ip6_append_data():
WARNING: CPU: 1 PID: 5042 at net/ipv6/ip6_output.c:1800 __ip6_append_data.isra.0+0x1be8/0x47f0 net/ipv6/ip6_output.c:1800
that occurs when MSG_SPLICE_PAGES is used to append more data to an already
partially occupied skbuff. The warning occurs when 'copy' is larger than
the amount of data in the message iterator. This is because the requested
length includes the transport header length when it shouldn't. This can be
triggered by, for example:
Fix this by only adding transhdrlen into the length if the write queue is
empty in l2tp_ip6_sendmsg(), analogously to how UDP does things.
l2tp_ip_sendmsg() looks like it won't suffer from this problem as it builds
the UDP packet itself.
Fixes: a32e0eec7042 ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6") Reported-by: syzbot+62cbf263225ae13ff153@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/0000000000001c12b30605378ce8@google.com/ Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric Dumazet <edumazet@google.com>
cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: David Ahern <dsahern@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: netdev@vger.kernel.org
cc: bpf@vger.kernel.org
cc: syzkaller-bugs@googlegroups.com Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While looking at a related syzbot report involving neigh_periodic_work(),
I found that I forgot to add an annotation when deleting an
RCU protected item from a list.
Readers use rcu_deference(*np), we need to use either
rcu_assign_pointer() or WRITE_ONCE() on writer side
to prevent store tearing.
I use rcu_assign_pointer() to have lockdep support,
this was the choice made in neigh_flush_dev().
Fixes: 767e97e1e0db ("neigh: RCU conversion of struct neighbour") Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@kernel.org> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Without this 'else' statement, an "usb" name goes into two handlers:
the first/previous 'if' statement _AND_ the for-loop over 'devtable',
but the latter is useless as it has no 'usb' device_id entry anyway.
Tested with allmodconfig before/after patch; no changes to *.mod.c:
git checkout v6.6-rc3
make -j$(nproc) allmodconfig
make -j$(nproc) olddefconfig
make -j$(nproc)
find . -name '*.mod.c' | cpio -pd /tmp/before
# apply patch
make -j$(nproc)
find . -name '*.mod.c' | cpio -pd /tmp/after
diff -r /tmp/before/ /tmp/after/
# no difference
Fixes: acbef7b76629 ("modpost: fix module autoloading for OF devices with generic compatible property") Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
With a SOCKMAP/SOCKHASH map and an sk_msg program user can steer messages
sent from one TCP socket (s1) to actually egress from another TCP
socket (s2):
There is a hard-coded assumption in the call-chain, that the egress
socket (s2) is a TCP socket.
However in commit 122e6c79efe1 ("sock_map: Update sock type checks for
UDP") we have enabled redirects to non-TCP sockets. This was done for the
sake of BPF sk_skb programs. There was no indention to support sk_msg
send-to-egress use case.
As a result, attempts to send-to-egress through a non-TCP socket lead to a
crash due to invalid downcast from sock to tcp_sock:
Reject selecting a non-TCP sockets as redirect target from a BPF sk_msg
program to prevent the crash. When attempted, user will receive an EACCES
error from send/sendto/sendmsg() syscall.
Fixes: 122e6c79efe1 ("sock_map: Update sock type checks for UDP") Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20230920102055.42662-1-jakub@cloudflare.com Signed-off-by: Sasha Levin <sashal@kernel.org>
If the NFS4CLNT_RUN_MANAGER flag got set just before we cleared
NFS4CLNT_MANAGER_RUNNING, then we might have won the race against
nfs4_schedule_state_manager(), and are responsible for handling the
recovery situation.
Fixes: aeabb3c96186 ("NFSv4: Fix a NFSv4 state manager deadlock") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Changing the direct dependencies of IMA_BLACKLIST_KEYRING and
IMA_LOAD_X509 caused them to no longer depend on IMA, but a
a configuration without IMA results in link failures:
arm-linux-gnueabi-ld: security/integrity/iint.o: in function `integrity_load_keys':
iint.c:(.init.text+0xd8): undefined reference to `ima_load_x509'
aarch64-linux-ld: security/integrity/digsig_asymmetric.o: in function `asymmetric_verify':
digsig_asymmetric.c:(.text+0x104): undefined reference to `ima_blacklist_keyring'
Adding explicit dependencies on IMA would fix this, but a more reliable
way to do this is to enclose the entire Kconfig file in an 'if IMA' block.
This also allows removing the existing direct dependencies.
The following call trace shows a deadlock issue due to recursive locking of
mutex "device_mutex". First lock acquire is in target_for_each_device() and
second in target_free_device().
The removal of IMA_TRUSTED_KEYRING made IMA_LOAD_X509
and IMA_BLACKLIST_KEYRING unavailable because the latter
two depend on the former. Since IMA_TRUSTED_KEYRING was
deprecated in favor of INTEGRITY_TRUSTED_KEYRING use it
as a dependency for the two Kconfigs affected by the
deprecation.
When regcache_rbtree_write() creates a new rbtree_node it was passing the
wrong bit number to regcache_rbtree_set_register(). The bit number is the
offset __in number of registers__, but in the case of creating a new block
regcache_rbtree_write() was not dividing by the address stride to get the
number of registers.
Fix this by dividing by map->reg_stride.
Compare with regcache_rbtree_read() where the bit is checked.
This bug meant that the wrong register was marked as present. The register
that was written to the cache could not be read from the cache because it
was not marked as cached. But a nearby register could be marked as having
a cached value even if it was never written to the cache.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com> Fixes: 3f4ff561bc88 ("regmap: rbtree: Make cache_present bitmap per node") Link: https://lore.kernel.org/r/20230922153711.28103-1-rf@opensource.cirrus.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On MT76x0, LNA gain should be applied for both external and internal LNA.
On MT76x2, LNA gain should be treated as 0 for external LNA.
Move the LNA type based logic to mt76x2 in order to fix mt76x0.
Fixes: 2daa67588f34 ("mt76x0: unify lna_gain parsing") Reported-by: Shiji Yang <yangshiji66@outlook.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230919194747.31647-1-nbd@nbd.name Signed-off-by: Sasha Levin <sashal@kernel.org>
Process the result of hdlc_open() and call uhdlc_close()
in case of an error. It is necessary to pass the error
code up the control flow, similar to a possible
error in request_irq().
Also add a hdlc_close() call to the uhdlc_close()
because the comment to hdlc_close() says it must be called
by the hardware driver when the HDLC device is being closed
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: c19b6d246a35 ("drivers/net: support hdlc function for QE-UCC") Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru> Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Only skip the code path trying to access the rfc1042 headers when the
buffer is too small, so the driver can still process packets without
rfc1042 headers.
Fixes: 119585281617 ("wifi: mwifiex: Fix OOB and integer underflow when rx packets") Signed-off-by: Pin-yen Lin <treapking@chromium.org> Acked-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Matthew Wang <matthewmwang@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20230908104308.1546501-1-treapking@chromium.org Signed-off-by: Sasha Levin <sashal@kernel.org>
A few lines above, space is kzalloc()'ed for:
sizeof(struct iwl_nvm_data) +
sizeof(struct ieee80211_channel) +
sizeof(struct ieee80211_rate)
'mvm->nvm_data' is a 'struct iwl_nvm_data', so it is fine.
At the end of this structure, there is the 'channels' flex array.
Each element is of type 'struct ieee80211_channel'.
So only 1 element is allocated in this array.
When doing:
mvm->nvm_data->bands[0].channels = mvm->nvm_data->channels;
We point at the first element of the 'channels' flex array.
So this is fine.
However, when doing:
mvm->nvm_data->bands[0].bitrates =
(void *)((u8 *)mvm->nvm_data->channels + 1);
because of the "(u8 *)" cast, we add only 1 to the address of the beginning
of the flex array.
It is likely that we want point at the 'struct ieee80211_rate' allocated
just after.
Remove the spurious casting so that the pointer arithmetic works as
expected.
The iwl_fw_ini_error_dump_range structure has conflicting alignment
requirements for the inner union and the outer struct:
In file included from drivers/net/wireless/intel/iwlwifi/fw/dbg.c:9:
drivers/net/wireless/intel/iwlwifi/fw/error-dump.h:312:2: error: field within 'struct iwl_fw_ini_error_dump_range' is less aligned than 'union iwl_fw_ini_error_dump_range::(anonymous at drivers/net/wireless/intel/iwlwifi/fw/error-dump.h:312:2)' and is usually due to 'struct iwl_fw_ini_error_dump_range' being packed, which can lead to unaligned accesses [-Werror,-Wunaligned-access]
union {
As the original intention was apparently to make the entire structure
unaligned, mark the innermost members the same way so the union
becomes packed as well.
There exists mtd devices with zero erasesize, which will trigger a
divide-by-zero exception while attaching ubi device.
Fix it by refusing attaching if mtd's erasesize is 0.
On some systems with Navi3x dGPU will attempt to use BACO for runtime
PM but fails to resume properly. This is because on these systems
the root port goes into D3cold which is incompatible with BACO.
This happens because in this case dGPU is connected to a bridge between
root port which causes BOCO detection logic to fail. Fix the intent of
the logic by looking at root port, not the immediate upstream bridge for
_PR3.
Cc: stable@vger.kernel.org Suggested-by: Jun Ma <Jun.Ma2@amd.com> Tested-by: David Perry <David.Perry@amd.com> Fixes: b10c1c5b3a4e ("drm/amdgpu: add check for ACPI power resources") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Callers of sock_sendmsg(), and similarly kernel_sendmsg(), in kernel
space may observe their value of msg_name change in cases where BPF
sendmsg hooks rewrite the send address. This has been confirmed to break
NFS mounts running in UDP mode and has the potential to break other
systems.
This patch:
1) Creates a new function called __sock_sendmsg() with same logic as the
old sock_sendmsg() function.
2) Replaces calls to sock_sendmsg() made by __sys_sendto() and
__sys_sendmsg() with __sock_sendmsg() to avoid an unnecessary copy,
as these system calls are already protected.
3) Modifies sock_sendmsg() so that it makes a copy of msg_name if
present before passing it down the stack to insulate callers from
changes to the send address.
Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/ Fixes: 1cedee13d25a ("bpf: Hooks for sys_sendmsg") Cc: stable@vger.kernel.org Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jordan Rife <jrife@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0bdf399342c5 ("net: Avoid address overwrite in kernel_connect")
ensured that kernel_connect() will not overwrite the address parameter
in cases where BPF connect hooks perform an address rewrite. This change
replaces direct calls to sock->ops->connect() in net with kernel_connect()
to make these call safe.
Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/ Fixes: d74bad4e74ee ("bpf: Hooks for sys_connect") Cc: stable@vger.kernel.org Reviewed-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Jordan Rife <jrife@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a TLV encoding scheme, the Length part represents the length after
the header containing the values for type and length. In this case,
`tlv_len` should be:
Notice that the `- 1` accounts for the one-element array `bitmap`, which
1-byte size is already included in `sizeof(*tlv_rxba)`.
So, if the above is correct, there is a double-counting of some members
in `struct mwifiex_ie_types_rxba_sync`, when `tlv_buf_left` and `tmp`
are calculated:
The above reflects the desired change: avoid counting 13 too many bytes;
which is the total size of the double-counted members in
`struct mwifiex_ie_types_rxba_sync`:
The flexible structure (a structure that contains a flexible-array member
at the end) `qed_ll2_tx_packet` is nested within the second layer of
`struct qed_ll2_info`:
The problem is that member `cbs` in `struct qed_ll2_info` is placed just
after an object of type `struct qed_ll2_tx_queue`, which is in itself
an implicit flexible structure, which by definition ends in a flexible
array member, in this case `bds_set`. This causes an undefined behavior
bug at run-time when dynamic memory is allocated for `bds_set`, which
could lead to a serious issue if `cbs` in `struct qed_ll2_info` is
overwritten by the contents of `bds_set`. Notice that the type of `cbs`
is a structure full of function pointers (and a cookie :) ):
Fix this by moving the declaration of `cbs` to the middle of its
containing structure `qed_ll2_info`, preventing it from being
overwritten by the contents of `bds_set` at run-time.
This bug was introduced in 2017, when `bds_set` was converted to a
one-element array, and started to be used as a Variable Length Object
(VLO) at run-time.
Fixes: f5823fe6897c ("qed: Add ll2 option to limit the number of bds per packet") Cc: stable@vger.kernel.org Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/ZQ+Nz8DfPg56pIzr@work Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the while loop of vringh_iov_xfer(), `partlen` could be 0 if one of
the `iov` has 0 lenght.
In this case, we should skip the iov and go to the next one.
But calling vringh_kiov_advance() with 0 lenght does not cause the
advancement, since it returns immediately if asked to advance by 0 bytes.
Let's restore the code that was there before commit b8c06ad4d67d
("vringh: implement vringh_kiov_advance()"), avoiding using
vringh_kiov_advance().
Fixes: b8c06ad4d67d ("vringh: implement vringh_kiov_advance()") Cc: stable@vger.kernel.org Reported-by: Jason Wang <jasowang@redhat.com> Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When device_register() fails, zfcp_port_release() will be called after
put_device(). As a result, zfcp_ccw_adapter_put() will be called twice: one
in zfcp_port_release() and one in the error path after device_register().
So the reference on the adapter object is doubly put, which may lead to a
premature free. Fix this by adjusting the error tag after
device_register().
Fixes: f3450c7b9172 ("[SCSI] zfcp: Replace local reference counting with common kref") Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Link: https://lore.kernel.org/r/20230923103723.10320-1-dinghao.liu@zju.edu.cn Acked-by: Benjamin Block <bblock@linux.ibm.com> Cc: stable@vger.kernel.org # v2.6.33+ Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marek writes:
The commit message states 'Cc: stable@vger.kernel.org # v5.18+'
and the commit should only be applied to Linux 5.18.y and newer,
on anything older it breaks PLL configuration due to missing
prerequisite patches.
Reported-by: Marek Vasut <marex@denx.de> Cc: Ahmad Fatoum <a.fatoum@pengutronix.de> Cc: Marco Felsch <m.felsch@pengutronix.de> Cc: Abel Vesa <abel.vesa@linaro.org> Link: https://lore.kernel.org/r/4e5fa5b2-66b8-8f0b-ccb9-c2b774054e4e@denx.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For blk-mq, queue release handler is usually called after
blk_mq_freeze_queue_wait() returns. However, the
q_usage_counter->release() handler may not be run yet at that time, so
this can cause a use-after-free.
Fix the issue by moving percpu_ref_exit() into blk_free_queue_rcu().
Since ->release() is called with rcu read lock held, it is agreed that
the race should be covered in caller per discussion from the two links.
rbd_dev_refresh() has been holding header_rwsem across header and
parent info read-in unnecessarily for ages. With commit 870611e4877e
("rbd: get snapshot context after exclusive lock is ensured to be
held"), the potential for deadlocks became much more real owning to
a) header_rwsem now nesting inside lock_rwsem and b) rw_semaphores
not allowing new readers after a writer is registered.
For example, assuming that I/O request 1, I/O request 2 and header
read-in request all target the same OSD:
1. I/O request 1 comes in and gets submitted
2. watch error occurs
3. rbd_watch_errcb() takes lock_rwsem for write, clears owner_cid and
releases lock_rwsem
4. after reestablishing the watch, rbd_reregister_watch() calls
rbd_dev_refresh() which takes header_rwsem for write and submits
a header read-in request
5. I/O request 2 comes in: after taking lock_rwsem for read in
__rbd_img_handle_request(), it blocks trying to take header_rwsem
for read in rbd_img_object_requests()
6. another watch error occurs
7. rbd_watch_errcb() blocks trying to take lock_rwsem for write
8. I/O request 1 completion is received by the messenger but can't be
processed because lock_rwsem won't be granted anymore
9. header read-in request completion can't be received, let alone
processed, because the messenger is stranded
Change rbd_dev_refresh() to take header_rwsem only for actually
updating rbd_dev->header. Header and parent info read-in don't need
any locking.
Cc: stable@vger.kernel.org # 0b035401c570: rbd: move rbd_dev_refresh() definition Cc: stable@vger.kernel.org # 510a7330c82a: rbd: decouple header read-in from updating rbd_dev->header Cc: stable@vger.kernel.org # c10311776f0a: rbd: decouple parent info read-in from updating rbd_dev Cc: stable@vger.kernel.org Fixes: 870611e4877e ("rbd: get snapshot context after exclusive lock is ensured to be held") Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn> Signed-off-by: Sasha Levin <sashal@kernel.org>
Unlike header read-in, parent info read-in is already decoupled in
get_parent_info(), but it's buried in rbd_dev_v2_parent_info() along
with the processing logic.
Separate the initial read-in and update read-in logic into
rbd_dev_setup_parent() and rbd_dev_update_parent() respectively and
have rbd_dev_v2_parent_info() just populate struct parent_image_info
(i.e. what get_parent_info() did). Some existing QoI issues, like
flatten of a standalone clone being disregarded on refresh, remain.
Make rbd_dev_header_info() populate a passed struct rbd_image_header
instead of rbd_dev->header and introduce rbd_dev_update_header() for
updating mutable fields in rbd_dev->header upon refresh. The initial
read-in of both mutable and immutable fields in rbd_dev_image_probe()
passes in rbd_dev->header so no update step is required there.
rbd_init_layout() is now called directly from rbd_dev_image_probe()
instead of individually in format 1 and format 2 implementations.
Move rbd_dev_refresh() definition further down to avoid having to
move struct parent_image_info definition in the next commit. This
spares some forward declarations too.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
[idryomov@gmail.com: backport to 5.10-6.1: context] Signed-off-by: Sasha Levin <sashal@kernel.org>
Although io-pgtable's non-leaf invalidations are always for full tables,
I missed that SVA also uses non-leaf invalidations, while being at the
mercy of whatever range the MMU notifier throws at it. This means it
definitely wants the previous TTL fix as well, since it also doesn't
know exactly which leaf level(s) may need invalidating, but it can also
give us less-aligned ranges wherein certain corners may lead to building
an invalid command where TTL, Num and Scale are all 0. It should be fine
to handle this by over-invalidating an extra page, since falling back to
a non-range command opens up a whole can of errata-flavoured worms.
When io-pgtable unmaps a whole table, rather than waste time walking it
to find the leaf entries to invalidate exactly, it simply expects
.tlb_flush_walk with nominal last-level granularity to invalidate any
leaf entries at higher intermediate levels as well. This works fine with
page-based invalidation, but with range commands we need to be careful
with the TTL hint - unconditionally setting it based on the given level
3 granule means that an invalidation for a level 1 table would strictly
not be required to affect level 2 block entries. It's easy to comply
with the expected behaviour by simply not setting the TTL hint for
non-leaf invalidations, so let's do that.
Accessing AA64MMFR1_EL1 is expensive in KVM guests, since it is emulated
in the hypervisor. In fact, ARM documentation mentions some feature
registers are not supposed to be accessed frequently by the OS, and
therefore should be emulated for guests [1].
Commit 0388f9c74330 ("arm64: mm: Implement
arch_wants_old_prefaulted_pte()") introduced a read of this register in
the page fault path. But, even when the feature of setting faultaround
pages with the old flag is disabled for a given cpu, we are still paying
the cost of checking the register on every pagefault. This results in an
explosion of vmexit events in KVM guests, which directly impacts the
performance of virtualized workloads. For instance, running kernbench
yields a 15% increase in system time solely due to the increased vmexit
cycles.
This patch avoids the extra cost by using the sanitized cached value.
It should be safe to do so, since this register mustn't change for a
given cpu.
The 'bytes' info in file 'per_cpu/cpu<X>/stats' means the number of
bytes in cpu buffer that have not been consumed. However, currently
after consuming data by reading file 'trace_pipe', the 'bytes' info
was not changed as expected.
The root cause is incorrect stat on cpu_buffer->read_bytes. To fix it:
1. When stat 'read_bytes', account consumed event in rb_advance_reader();
2. When stat 'entries_bytes', exclude the discarded padding event which
is smaller than minimum size because it is invisible to reader. Then
use rb_page_commit() instead of BUF_PAGE_SIZE at where accounting for
page-based read/remove/overrun.
Also correct the comments of ring_buffer_bytes_cpu() in this patch.
Link: https://lore.kernel.org/linux-trace-kernel/20230921125425.1708423-1-zhengyejian1@huawei.com Cc: stable@vger.kernel.org Fixes: c64e148a3be3 ("trace: Add ring buffer stats to measure rate of events") Signed-off-by: Zheng Yejian <zhengyejian1@huawei.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The comment refers to mm/slob.c which is being removed. It comes from
commit ed56829cb319 ("ring_buffer: reset buffer page when freeing") and
according to Steven the borrowed code was a page mapcount and mapping
reset, which was later removed by commit e4c2ce82ca27 ("ring_buffer:
allocate buffer page pointer"). Thus the comment is not accurate anyway,
remove it.
Commit 4dc73c679114 reintroduces the deadlock that was fixed by commit aeabb3c96186 ("NFSv4: Fix a NFSv4 state manager deadlock") because it
prevents the setup of new threads to handle reboot recovery, while the
older recovery thread is stuck returning delegations.
Fixes: 4dc73c679114 ("NFSv4: keep state manager thread active if swap is enabled") Cc: stable@vger.kernel.org Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 4dc73c679114 ("NFSv4: keep state manager thread active if swap is enabled") Signed-off-by: Benjamin Coddington <bcodding@redhat.com> Reviewed-by: NeilBrown <neilb@suse.de> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Stable-dep-of: 956fd46f97d2 ("NFSv4: Fix a state manager thread deadlock regression") Signed-off-by: Sasha Levin <sashal@kernel.org>
Tegra audio graph card has many DAI links which connects internal
AHUB modules and external audio codecs. Since these are DPCM links,
hw_params() call in the machine driver happens for each connected
BE link and PLLA is updated every time. This is not really needed
for all links as only I/O link DAIs derive respective clocks from
PLLA_OUT0 and thus from PLLA. Hence add checks to limit the clock
updates to DAIs over I/O links.
This found to be fixing a DMIC clock discrepancy which is suspected
to happen because of back to back quick PLLA and PLLA_OUT0 rate
updates. This was observed on Jetson TX2 platform where DMIC clock
ended up with unexpected value.
Fixes: 202e2f774543 ("ASoC: tegra: Add audio graph based card driver") Cc: stable@vger.kernel.org Signed-off-by: Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1694098945-32760-3-git-send-email-spujar@nvidia.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Make sure that the device is not runtime suspended before explicitly
disabling the clocks on probe failure and on driver unbind to avoid a
clock enable-count imbalance.
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Jakub Kicinski says:
We've got some new kdoc warnings here:
net/netfilter/nft_set_pipapo.c:1557: warning: Function parameter or member '_set' not described in 'pipapo_gc'
net/netfilter/nft_set_pipapo.c:1557: warning: Excess function parameter 'set' description in 'pipapo_gc'
include/net/netfilter/nf_tables.h:577: warning: Function parameter or member 'dead' not described in 'nft_set'
Fixes: 5f68718b34a5 ("netfilter: nf_tables: GC transaction API to avoid race with control plane") Fixes: f6c383b8c31a ("netfilter: nf_tables: adapt set backend to use GC transaction API") Reported-by: Jakub Kicinski <kuba@kernel.org> Closes: https://lore.kernel.org/netdev/20230810104638.746e46f1@kernel.org/ Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The elf-fdpic loader hard sets the process personality to either
PER_LINUX_FDPIC for true elf-fdpic binaries or to PER_LINUX for normal ELF
binaries (in this case they would be constant displacement compiled with
-pie for example). The problem with that is that it will lose any other
bits that may be in the ELF header personality (such as the "bug
emulation" bits).
On the ARM architecture the ADDR_LIMIT_32BIT flag is used to signify a
normal 32bit binary - as opposed to a legacy 26bit address binary. This
matters since start_thread() will set the ARM CPSR register as required
based on this flag. If the elf-fdpic loader loses this bit the process
will be mis-configured and crash out pretty quickly.
Modify elf-fdpic loader personality setting so that it preserves the upper
three bytes by using the SET_PERSONALITY macro to set it. This macro in
the generic case sets PER_LINUX and preserves the upper bytes.
Architectures can override this for their specific use case, and ARM does
exactly this.
The problem shows up quite easily running under qemu using the ARM
architecture, but not necessarily on all types of real ARM hardware. If
the underlying ARM processor does not support the legacy 26-bit addressing
mode then everything will work as expected.
Link: https://lkml.kernel.org/r/20230907011808.2985083-1-gerg@kernel.org Fixes: 1bde925d23547 ("fs/binfmt_elf_fdpic.c: provide NOMMU loader for regular ELF binaries") Signed-off-by: Greg Ungerer <gerg@kernel.org> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christian Brauner <brauner@kernel.org> Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Greg Ungerer <gerg@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On certain SATA controllers, softreset fails after wakeup from S2RAM with
the message "softreset failed (1st FIS failed)", sometimes resulting in
drives not being detected again. With the increased timeout, this issue
is avoided. Instead, "softreset failed (device not ready)" is now
logged 1-2 times; this later failure seems to cause fewer problems
however, and the drives are detected reliably once they've spun up and
the probe is retried.
The issue was observed with the primary SATA controller of the QNAP
TS-453B, which is an "Intel Corporation Celeron/Pentium Silver Processor
SATA Controller [8086:31e3] (rev 06)" integrated in the Celeron J4125 CPU,
and the following drives:
The SATA controller seems to be more relevant to this issue than the
drives, as the same drives are always detected reliably on the secondary
SATA controller on the same board (an ASMedia 106x) without any "softreset
failed" errors even without the increased timeout.
Fixes: e7d3ef13d52a ("libata: change drive ready wait after hard reset to 5s") Cc: stable@vger.kernel.org Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
libsas does its own domain based power management of ports. For such
ports, libata should not use a device type defining power management
operations as executing these operations for suspend/resume in addition
to libsas calls to ata_sas_port_suspend() and ata_sas_port_resume() is
not necessary (and likely dangerous to do, even though problems are not
seen currently).
Introduce the new ata_port_sas_type device_type for ports managed by
libsas. This new device type is used in ata_tport_add() and is defined
without power management operations.
Fixes: 2fcbdcb4c802 ("[SCSI] libata: export ata_port suspend/resume infrastructure for sas") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: John Garry <john.g.garry@oracle.com> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever an ATA adapter driver is removed (e.g. rmmod),
ata_port_detach() is called repeatedly for all the adapter ports to
remove (unload) the devices attached to the port and delete the port
device itself. Removing of devices is done using libata EH with the
ATA_PFLAG_UNLOADING port flag set. This causes libata EH to execute
ata_eh_unload() which disables all devices attached to the port.
ata_port_detach() finishes by calling scsi_remove_host() to remove the
scsi host associated with the port. This function will trigger the
removal of all scsi devices attached to the host and in the case of
disks, calls to sd_shutdown() which will flush the device write cache
and stop the device. However, given that the devices were already
disabled by ata_eh_unload(), the synchronize write cache command and
start stop unit commands fail. E.g. running "rmmod ahci" with first
removing sd_mod results in error messages like:
The function ata_port_request_pm() checks the port flag
ATA_PFLAG_PM_PENDING and calls ata_port_wait_eh() if this flag is set to
ensure that power management operations for a port are not scheduled
simultaneously. However, this flag check is done without holding the
port lock.
Fix this by taking the port lock on entry to the function and checking
the flag under this lock. The lock is released and re-taken if
ata_port_wait_eh() needs to be called. The two WARN_ON() macros checking
that the ATA_PFLAG_PM_PENDING flag was cleared are removed as the first
call is racy and the second one done without holding the port lock.
Fixes: 5ef41082912b ("ata: add ata port system PM callbacks") Cc: stable@vger.kernel.org Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by: Bart Van Assche <bvanassche@acm.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alex reported that running ssh over IPv6 does not work with
Thunderbolt/USB4 networking driver. The reason for that is that driver
should call skb_is_gso() before calling skb_is_gso_v6(), and it should
not return false after calculates the checksum successfully. This probably
was a copy paste error from the original driver where it was done properly.
Reported-by: Alex Balcanquall <alex@alexbal.com> Fixes: e69b6c02b4c3 ("net: Add support for networking over Thunderbolt cable") Cc: stable@vger.kernel.org Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcus and Satya reported an issue where BTF_ID macro generates same
symbol in separate objects and that breaks final vmlinux link.
ld.lld: error: ld-temp.o <inline asm>:14577:1: symbol
'__BTF_ID__struct__cgroup__624' is already defined
This can be triggered under specific configs when __COUNTER__ happens to
be the same for the same symbol in two different translation units,
which is already quite unlikely to happen.
Add __LINE__ number suffix to make BTF_ID symbol more unique, which is
not a complete fix, but it would help for now and meanwhile we can work
on better solution as suggested by Andrii.
Marcus and Satya reported an issue where BTF_ID macro generates same
symbol in separate objects and that breaks final vmlinux link.
ld.lld: error: ld-temp.o <inline asm>:14577:1: symbol
'__BTF_ID__struct__cgroup__624' is already defined
This can be triggered under specific configs when __COUNTER__ happens to
be the same for the same symbol in two different translation units,
which is already quite unlikely to happen.
Add __LINE__ number suffix to make BTF_ID symbol more unique, which is
not a complete fix, but it would help for now and meanwhile we can work
on better solution as suggested by Andrii.
A user reported some issues with smaller file systems that get very
full. While investigating this issue I noticed that df wasn't showing
100% full, despite having 0 chunk space and having < 1MiB of available
metadata space.
This turns out to be an overflow issue, we're doing:
to determine if there's not enough space to make metadata allocations,
which overflows if total_available_metadata_space is < 4M. Fix this by
checking to see if our available space is greater than the 4M threshold.
This makes df properly report 100% usage on the file system.
CC: stable@vger.kernel.org # 4.14+ Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was discovered that the ring buffer polling was incorrectly stating
that read would not block, but that's because polling did not take into
account that reads will block if the "buffer-percent" was set. Instead,
the ring buffer polling would say reads would not block if there was any
data in the ring buffer. This was incorrect behavior from a user space
point of view. This was fixed by commit 42fb0a1e84ff by having the polling
code check if the ring buffer had more data than what the user specified
"buffer percent" had.
The problem now is that the polling code did not register itself to the
writer that it wanted to wait for a specific "full" value of the ring
buffer. The result was that the writer would wake the polling waiter
whenever there was a new event. The polling waiter would then wake up, see
that there's not enough data in the ring buffer to notify user space and
then go back to sleep. The next event would wake it up again.
Before the polling fix was added, the code would wake up around 100 times
for a hackbench 30 benchmark. After the "fix", due to the constant waking
of the writer, it would wake up over 11,0000 times! It would never leave
the kernel, so the user space behavior was still "correct", but this
definitely is not the desired effect.
To fix this, have the polling code add what it's waiting for to the
"shortest_full" variable, to tell the writer not to wake it up if the
buffer is not as full as it expects to be.
Note, after this fix, it appears that the waiter is now woken up around 2x
the times it was before (~200). This is a tremendous improvement from the
11,000 times, but I will need to spend some time to see why polling is
more aggressive in its wakeups than the read blocking code.
Link: https://lore.kernel.org/linux-trace-kernel/20230929180113.01c2cae3@rorschach.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Fixes: 42fb0a1e84ff ("tracing/ring-buffer: Have polling block on watermark") Reported-by: Julia Lawall <julia.lawall@inria.fr> Tested-by: Julia Lawall <julia.lawall@inria.fr> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The no-MMU implementation of /proc/<pid>/map doesn't normally release
the mmap read lock, because it uses !IS_ERR_OR_NULL(_vml) to determine
whether to release the lock. Since _vml is NULL when the end of the
mappings is reached, the lock is not released.
Reading /proc/1/maps twice doesn't cause a hang because it only
takes the read lock, which can be taken multiple times and therefore
doesn't show any problem if the lock isn't released. Instead, you need
to perform some operation that attempts to take the write lock after
reading /proc/<pid>/maps. To actually reproduce the bug, compile the
following code as 'proc_maps_bug':
Without this patch, mmap() will hang and the command will never
complete.
This code was incorrectly adapted from the MMU implementation, which at
the time released the lock in m_next() before returning the last entry.
The MMU implementation has diverged further from the no-MMU version since
then, so this patch brings their locking and error handling into sync,
fixing the bug and hopefully avoiding similar issues in the future.
The problem this commit is intended to fix was comprehensively fixed
in commit 7de62bc09fe6 ("SUNRPC dont update timeout value on connection
reset").
Since then, this commit has been preventing the correct timeout of soft
mounted requests.
Cc: stable@vger.kernel.org # 5.9.x: 09252177d5f9: SUNRPC: Handle major timeout in xprt_adjust_timeout() Cc: stable@vger.kernel.org # 5.9.x: 7de62bc09fe6: SUNRPC dont update timeout value on connection reset Cc: stable@vger.kernel.org # 5.9.x Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is unionized with the actual link flags, so they can of course be
set and they will be evaluated further down. If not we fail any LINKAT
that has to set option flags.
Fixes: cf30da90bc3a ("io_uring: add support for IORING_OP_LINKAT") Cc: stable@vger.kernel.org Reported-by: Thomas Leonard <talex5@gmail.com> Link: https://github.com/axboe/liburing/issues/955 Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During RCU-boost testing with the TREE03 rcutorture config, I found that
after a few hours, the machine locks up.
On tracing, I found that there is a live lock happening between 2 CPUs.
One CPU has an RT task running, while another CPU is being offlined
which also has an RT task running. During this offlining, all threads
are migrated. The migration thread is repeatedly scheduled to migrate
actively running tasks on the CPU being offlined. This results in a live
lock because select_fallback_rq() keeps picking the CPU that an RT task
is already running on only to get pushed back to the CPU being offlined.
It is anyway pointless to pick CPUs for pushing tasks to if they are
being offlined only to get migrated away to somewhere else. This could
also add unwanted latency to this task.
Fix these issues by not selecting CPUs in RT if they are not 'active'
for scheduling, using the cpu_active_mask. Other parts in core.c already
use cpu_active_mask to prevent tasks from being put on CPUs going
offline.
With this fix I ran the tests for days and could not reproduce the
hang. Without the patch, I hit it in a few hours.
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org> Signed-off-by: Ingo Molnar <mingo@kernel.org> Tested-by: Paul E. McKenney <paulmck@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230923011409.3522762-1-joel@joelfernandes.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initial booting is setting the task flag to idle (PF_IDLE) by the call
path sched_init() -> init_idle(). Having the task idle and calling
call_rcu() in kernel/rcu/tiny.c means that TIF_NEED_RESCHED will be
set. Subsequent calls to any cond_resched() will enable IRQs,
potentially earlier than the IRQ setup has completed. Recent changes
have caused just this scenario and IRQs have been enabled early.
This causes a warning later in start_kernel() as interrupts are enabled
before they are fully set up.
Fix this issue by setting the PF_IDLE flag later in the boot sequence.
Although the boot task was marked as idle since (at least) d80e4fda576d,
I am not sure that it is wrong to do so. The forced context-switch on
idle task was introduced in the tiny_rcu update, so I'm going to claim
this fixes 5f6130fa52ee.
Fixes: 5f6130fa52ee ("tiny_rcu: Directly force QS when call_rcu_[bh|sched]() on idle_task") Signed-off-by: Liam R. Howlett <Liam.Howlett@oracle.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/linux-mm/CAMuHMdWpvpWoDa=Ox-do92czYRvkok6_x6pYUH+ZouMcJbXy+Q@mail.gmail.com/ Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For REPORT SUPPORTED OPERATION CODES command, the service action field is
defined as bits 0-4 in the second byte in the CDB. Bits 5-7 in the second
byte are reserved.
Only look at the service action field in the second byte when determining
if the MAINTENANCE IN opcode is a REPORT SUPPORTED OPERATION CODES command.
This matches how we only look at the service action field in the second
byte when determining if the SERVICE ACTION IN(16) opcode is a READ
CAPACITY(16) command (reserved bits 5-7 in the second byte are ignored).
Fixes: 7b2030942859 ("libata: Add support for SCT Write Same") Cc: stable@vger.kernel.org Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chain binding only requires the rule addition/insertion command within
the same transaction. Removal of rules from chain bindings within the
same transaction makes no sense, userspace does not utilize this
feature. Replace nft_chain_is_bound() check to nft_chain_binding() in
rule deletion commands. Replace command implies a rule deletion, reject
this command too.
Rule flush command can also safely rely on this nft_chain_binding()
check because unbound chains are not allowed since 62e1e94b246e
("netfilter: nf_tables: reject unbound chain set before commit phase").
Fixes: d0e2c7de92c7 ("netfilter: nf_tables: add NFT_CHAIN_BINDING") Reported-by: Kevin Rich <kevinrich1337@gmail.com> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In nilfs_gccache_submit_read_data(), brelse(bh) is called to drop the
reference count of bh when the call to nilfs_dat_translate() fails. If
the reference count hits 0 and its owner page gets unlocked, bh may be
freed. However, bh->b_page is dereferenced to put the page after that,
which may result in a use-after-free bug. This patch moves the release
operation after unlocking and putting the page.
NOTE: The function in question is only called in GC, and in combination
with current userland tools, address translation using DAT does not occur
in that function, so the code path that causes this issue will not be
executed. However, it is possible to run that code path by intentionally
modifying the userland GC library or by calling the GC ioctl directly.
[konishi.ryusuke@gmail.com: NOTE added to the commit log] Link: https://lkml.kernel.org/r/1543201709-53191-1-git-send-email-bianpan2016@163.com Link: https://lkml.kernel.org/r/20230921141731.10073-1-konishi.ryusuke@gmail.com Fixes: a3d93f709e89 ("nilfs2: block cache for garbage collection") Signed-off-by: Pan Bian <bianpan2016@163.com> Reported-by: Ferry Meng <mengferry@linux.alibaba.com> Closes: https://lkml.kernel.org/r/20230818092022.111054-1-mengferry@linux.alibaba.com Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the leaf driver wants to use IRQ polling (irq = 0) and
IIR register shows that an interrupt happened in the 8250 hardware
the IRQ data can be NULL. In such a case we need to skip the wake
event as we came to this path from the timer interrupt and quite
likely system is already awake.
Without this fix we have got an Oops:
serial8250: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A
...
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: 0010:serial8250_handle_irq+0x7c/0x240
Call Trace:
? serial8250_handle_irq+0x7c/0x240
? __pfx_serial8250_timeout+0x10/0x10
projects / linux-stable / log