There are race conditions that may lead to inet6_dev refcount underflow
in xfrm6_dst_destroy() and rt6_uncached_list_flush_dev().
One of the refcount underflow bugs is shown below:
(cpu 1) | (cpu 2)
xfrm6_dst_destroy() |
... |
in6_dev_put() |
| rt6_uncached_list_flush_dev()
... | ...
| in6_dev_put()
rt6_uncached_list_del() | ...
... |
xfrm6_dst_destroy() calls rt6_uncached_list_del() after in6_dev_put(),
so rt6_uncached_list_flush_dev() has a chance to call in6_dev_put()
again for the same inet6_dev.
Fix it by moving in6_dev_put() after rt6_uncached_list_del() in
xfrm6_dst_destroy().
The code pattern of memcpy(dst, src, strlen(src)) is almost always
wrong. In this case it is wrong because it leaves memory uninitialized
if it is less than sizeof(ni->name), and overflows ni->name when longer.
Normally strtomem_pad() could be used here, but since ni->name is a
trailing array in struct hci_mon_new_index, compilers that don't support
-fstrict-flex-arrays=3 can't tell how large this array is via
__builtin_object_size(). Instead, open-code the helper and use sizeof()
since it will work correctly.
Additionally mark ni->name as __nonstring since it appears to not be a
%NUL terminated C string.
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Cc: Edward AD <twuufnxlz@gmail.com> Cc: Marcel Holtmann <marcel@holtmann.org> Cc: Johan Hedberg <johan.hedberg@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: linux-bluetooth@vger.kernel.org Cc: netdev@vger.kernel.org Fixes: 18f547f3fc07 ("Bluetooth: hci_sock: fix slab oob read in create_monitor_event") Link: https://lore.kernel.org/lkml/202310110908.F2639D3276@keescook/ Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Looks like the driver sleep pins configuration is unusable. Adding the
sleep pins causes the usb phy to not respond. We need to use the default
pins in probe, and only set sleep pins at phy_mdm6600_device_power_off().
As the modem can also be booted to a serial port mode for firmware
flashing, let's make the pin changes limited to probe and remove. For
probe, we get the default pins automatically. We only need to set the
sleep pins in phy_mdm6600_device_power_off() to prevent the modem from
waking up because the gpio line glitches.
If it turns out that we need a separate state for phy_mdm6600_power_on()
and phy_mdm6600_power_off(), we can use the pinctrl idle state.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Cc: Sebastian Reichel <sre@kernel.org> Fixes: 2ad2af081622 ("phy: mapphone-mdm6600: Improve phy related runtime PM calls") Signed-off-by: Tony Lindgren <tony@atomide.com> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Link: https://lore.kernel.org/r/20230913060433.48373-3-tony@atomide.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit d644e0d79829 ("phy: mapphone-mdm6600: Fix PM error handling in
phy_mdm6600_probe") caused a regression where we now unconditionally
disable runtime PM at the end of the probe while it is only needed on
errors.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Miaoqian Lin <linmq006@gmail.com> Cc: Pavel Machek <pavel@ucw.cz> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Fixes: d644e0d79829 ("phy: mapphone-mdm6600: Fix PM error handling in phy_mdm6600_probe") Signed-off-by: Tony Lindgren <tony@atomide.com> Link: https://lore.kernel.org/r/20230913060433.48373-1-tony@atomide.com Signed-off-by: Vinod Koul <vkoul@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Free the "priv" pointer before returning the error code.
Fixes: 90eb6b59d311 ("ASoC: pxa-ssp: add support for an external clock in devicetree") Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/84ac2313-1420-471a-b2cb-3269a2e12a7c@moroto.mountain Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We found a glitch when configuring the pad as output high. To avoid this
glitch, move the data value setting before direction config in the
function vf610_gpio_direction_output().
Map 0x2a to KEY_SELECTIVE_SCREENSHOT mirroring how similar hotkeys
are mapped on other laptops.
PrintScreem and CapsLock are also reported as normal PS/2 keyboard events,
map these event codes to KE_IGNORE to avoid "Unknown key code 0x%x\n" log
messages.
Reported-by: James John <me@donjajo.com> Closes: https://lore.kernel.org/platform-driver-x86/a2c441fe-457e-44cf-a146-0ecd86b037cf@donjajo.com/ Closes: https://bbs.archlinux.org/viewtopic.php?pid=2123716 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20231017090725.38163-4-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before this commit all the NOTIFY_BRNDOWN_MIN - NOTIFY_BRNDOWN_MAX
aka 0x20 - 0x2e events were mapped to 0x20.
This mapping is causing issues on new laptop models which actually
send 0x2b events for printscreen presses and 0x2c events for
capslock presses, which get translated into spurious brightness-down
presses.
The plan is disable the 0x11-0x2e special mapping on laptops
where asus-wmi does not register a backlight-device to avoid
the spurious brightness-down keypresses. New laptops always send
0x2e for brightness-down presses, change the special internal
ASUS_WMI_BRN_DOWN value from 0x20 to 0x2e to match this in
preparation for fixing the spurious brightness-down presses.
This change does not have any functional impact since all
of 0x20 - 0x2e is mapped to ASUS_WMI_BRN_DOWN first and only
then checked against the keymap code and the new 0x2e
value is still in the 0x20 - 0x2e range.
Reported-by: James John <me@donjajo.com> Closes: https://lore.kernel.org/platform-driver-x86/a2c441fe-457e-44cf-a146-0ecd86b037cf@donjajo.com/ Closes: https://bbs.archlinux.org/viewtopic.php?pid=2123716 Signed-off-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20231017090725.38163-2-hdegoede@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If platform_profile_register() fails, the driver does not propagate
the error, but instead probes successfully. This means when the driver
unbinds, the a warning might be issued by platform_profile_remove().
Fix this by propagating the error back to the caller of
surface_platform_profile_probe().
Compile-tested only.
Fixes: b78b4982d763 ("platform/surface: Add platform profile driver") Signed-off-by: Armin Wolf <W_Armin@gmx.de> Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> Tested-by: Maximilian Luz <luzmaximilian@gmail.com> Link: https://lore.kernel.org/r/20231014235449.288702-1-W_Armin@gmx.de Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If name_show() is non unique, this test will try to install a kprobe on this
function which should fail returning EADDRNOTAVAIL.
On kernel where name_show() is not unique, this test is skipped.
Since the fixed commits both zdev->iommu_bitmap and zdev->lazy_bitmap
are allocated as vzalloc(zdev->iommu_pages / 8). The problem is that
zdev->iommu_bitmap is a pointer to unsigned long but the above only
yields an allocation that is a multiple of sizeof(unsigned long) which
is 8 on s390x if the number of IOMMU pages is a multiple of 64.
This in turn is the case only if the effective IOMMU aperture is
a multiple of 64 * 4K = 256K. This is usually the case and so didn't
cause visible issues since both the virt_to_phys(high_memory) reduced
limit and hardware limits use nice numbers.
Under KVM, and in particular with QEMU limiting the IOMMU aperture to
the vfio DMA limit (default 65535), it is possible for the reported
aperture not to be a multiple of 256K however. In this case we end up
with an iommu_bitmap whose allocation is not a multiple of
8 causing bitmap operations to access it out of bounds.
Sadly we can't just fix this in the obvious way and use bitmap_zalloc()
because for large RAM systems (tested on 8 TiB) the zdev->iommu_bitmap
grows too large for kmalloc(). So add our own bitmap_vzalloc() wrapper.
This might be a candidate for common code, but this area of code will
be replaced by the upcoming conversion to use the common code DMA API on
s390 so just add a local routine.
Fixes: 224593215525 ("s390/pci: use virtual memory for iommu bitmap") Fixes: 13954fd6913a ("s390/pci_dma: improve lazy flush for unmap") Cc: stable@vger.kernel.org Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com> Signed-off-by: Vasily Gorbik <gor@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because group consistency is non-atomic between parent (filedesc) and children
(inherited) events, it is possible for PERF_FORMAT_GROUP read() to try and sum
non-matching counter groups -- with non-sensical results.
Add group_generation to distinguish the case where a parent group removes and
adds an event and thus has the same number, but a different configuration of
events as inherited groups.
This became a problem when commit fa8c269353d5 ("perf/core: Invert
perf_read_group() loops") flipped the order of child_list and sibling_list.
Previously it would iterate the group (sibling_list) first, and for each
sibling traverse the child_list. In this order, only the group composition of
the parent is relevant. By flipping the order the group composition of the
child (inherited) events becomes an issue and the mis-match in group
composition becomes evident.
That said; even prior to this commit, while reading of a group that is not
equally inherited was not broken, it still made no sense.
(Ab)use ECHILD as error return to indicate issues with child process group
composition.
acpi_register_gsi() should return a negative value in case of failure.
Currently, it returns the return value from irq_create_fwspec_mapping().
However, irq_create_fwspec_mapping() returns 0 for failure. Fix the
issue by returning -EINVAL if irq_create_fwspec_mapping() returns zero.
Fixes: d44fa3d46079 ("ACPI: Add support for ResourceSource/IRQ domain mapping") Cc: 4.11+ <stable@vger.kernel.org> # 4.11+ Signed-off-by: Sunil V L <sunilvl@ventanamicro.com>
[ rjw: Rename a new local variable ] Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patches fixes commit 51d674a5e488 "NFSv4.1: use
EXCHGID4_FLAG_USE_PNFS_DS for DS server", purpose of that
commit was to mark EXCHANGE_ID to the DS with the appropriate
flag.
However, connection to MDS can return both EXCHGID4_FLAG_USE_PNFS_DS
and EXCHGID4_FLAG_USE_PNFS_MDS set but previous patch would only
remember the USE_PNFS_DS and for the 2nd EXCHANGE_ID send that
to the MDS.
Instead, just mark the pnfs path exclusively.
Fixes: 51d674a5e488 ("NFSv4.1: use EXCHGID4_FLAG_USE_PNFS_DS for DS server") Signed-off-by: Olga Kornievskaia <kolga@netapp.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are not allowed to call pnfs_mark_matching_lsegs_return() without
also holding a reference to the layout header, since doing so could lead
to the reference count going to zero when we call
pnfs_layout_remove_lseg(). This again can lead to a hang when we get to
nfs4_evict_inode() and are unable to clear the layout pointer.
pnfs_layout_return_unused_byserver() is guilty of this behaviour, and
has been seen to trigger the refcount warning prior to a hang.
Fixes: b6d49ecd1081 ("NFSv4: Fix a pNFS layout related use-after-free race when freeing the inode") Cc: stable@vger.kernel.org Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OEMID is an 8-bit binary number rather than 16-bit as the current code
parses for. The OEMID occupies bits [111:104] in the CID register, see the
eMMC spec JESD84-B51 paragraph 7.2.3. It seems that the 16-bit comes from
the legacy MMC specs (v3.31 and before).
Let's fix the parsing by simply move to use 8-bit instead of 16-bit. This
means we ignore the impact on some of those old MMC cards that may be out
there, but on the other hand this shouldn't be a problem as the OEMID seems
not be an important feature for these cards.
tuning only support in 4-bit mode or 8 bit mode, so in 1-bit mode,
need to hold retuning.
Find this issue when use manual tuning method on imx93. When system
resume back, SDIO WIFI try to switch back to 4 bit mode, first will
trigger retuning, and all tuning command failed.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: dfa13ebbe334 ("mmc: host: Add facility to support re-tuning") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20230830093922.3095850-1-haibo.chen@nxp.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the exact mapping type driver was not available, the old
physmap_of_core driver fell back to mapping the region as ROM.
Unfortunately this feature was lost when the DT and pdata cases were
merged. Revive this useful feature.
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: Michal Simek <michal.simek@amd.com> Cc: stable@vger.kernel.org Fixes: 88ffef1b65cf ("mtd: rawnand: arasan: Support the hardware BCH ECC engine") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Acked-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-2-miquel.raynal@bootlin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
The NAND core complies with the ONFI specification, which itself
mentions that after any program or erase operation, a status check
should be performed to see whether the operation was finished *and*
successful.
The NAND core offers helpers to finish a page write (sending the
"PAGE PROG" command, waiting for the NAND chip to be ready again, and
checking the operation status). But in some cases, advanced controller
drivers might want to optimize this and craft their own page write
helper to leverage additional hardware capabilities, thus not always
using the core facilities.
Some drivers, like this one, do not use the core helper to finish a page
write because the final cycles are automatically managed by the
hardware. In this case, the additional care must be taken to manually
perform the final status check.
Let's read the NAND chip status at the end of the page write helper and
return -EIO upon error.
Cc: Michal Simek <michal.simek@amd.com> Cc: stable@vger.kernel.org Fixes: 08d8c62164a3 ("mtd: rawnand: pl353: Add support for the ARM PL353 SMC NAND controller") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Tested-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/linux-mtd/20230717194221.229778-3-miquel.raynal@bootlin.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_get_valid_name() overwrites the netdev's name on success.
This makes it hard to use in prepare-commit-like fashion,
where we do validation first, and "commit" to the change
later.
Factor out a helper which lets us save the new name to a buffer.
Use it to fix the problem of notification on netns move having
incorrect name:
5: eth0: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default
link/ether be:4d:58:f9:d5:40 brd ff:ff:ff:ff:ff:ff
6: eth1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default
link/ether 1e:4a:34:36:e3:cd brd ff:ff:ff:ff:ff:ff
[ ~]# ip link set dev eth0 netns 1 name eth1
ip monitor inside netns:
Deleted inet eth0
Deleted inet6 eth0
Deleted 5: eth1: <BROADCAST,NOARP> mtu 1500 qdisc noop state DOWN group default
link/ether be:4d:58:f9:d5:40 brd ff:ff:ff:ff:ff:ff new-netnsid 0 new-ifindex 7
Name is reported as eth1 in old netns for ifindex 5, already renamed.
Fixes: d90310243fd7 ("net: device name allocation cleanups") Signed-off-by: Jakub Kicinski <kuba@kernel.org> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
__dev_get_by_name is currently used to either retrieve a net device
reference using its name or to check if a name is already used by a
registered net device (per ns). In the later case there is no need to
return a reference to a net device.
Introduce a new helper, netdev_name_in_use, to check if a name is
currently used by a registered net device without leaking a reference
the corresponding net device. This helper uses netdev_name_node_lookup
instead of __dev_get_by_name as we don't need the extra logic retrieving
a reference to the corresponding net device.
Signed-off-by: Antoine Tenart <atenart@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 311cca40661f ("net: fix ifname in netlink ntf during netns move") Signed-off-by: Sasha Levin <sashal@kernel.org>
memcmp is not consider safe to use with cryptographic secrets:
'Do not use memcmp() to compare security critical data, such as
cryptographic secrets, because the required CPU time depends on the
number of equal bytes.'
While usage of memcmp for ZERO_KEY may not be considered a security
critical data, it can lead to more usage of memcmp with pairing keys
which could introduce more security problems.
Fixes: 455c2ff0a558 ("Bluetooth: Fix BR/EDR out-of-band pairing with only initiator data") Fixes: 33155c4aae52 ("Bluetooth: hci_event: Ignore NULL link key") Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Currently, whenever fw issues a change ownership event, the PF that owns
the fw tracer drops its ownership directly and the other PFs try to pick
up the ownership via what MTRC register suggests.
In some cases, driver releases the ownership of the tracer and reacquires
it later on. Whenever the driver releases ownership of the tracer, fw
issues a change ownership event. This event can be delayed and come after
driver has reacquired ownership of the tracer. Thus the late event will
trigger the tracer owner PF to release the ownership again and lead to a
scenario where no PF is owning the tracer.
To prevent the scenario described above, when handling a change
ownership event, do not drop ownership of the tracer directly, instead
read the fw MTRC register to retrieve the up-to-date owner of the tracer
and set it accordingly in driver level.
At btrfs_realloc_node() we have these checks to verify we are not using a
stale transaction (a past transaction with an unblocked state or higher),
and the only thing we do is to trigger two WARN_ON(). This however is a
critical problem, highly unexpected and if it happens it's most likely due
to a bug, so we should error out and turn the fs into error state so that
such issue is much more easily noticed if it's triggered.
The problem is critical because in btrfs_realloc_node() we COW tree blocks,
and using such stale transaction will lead to not persisting the extent
buffers used for the COW operations, as allocating tree block adds the
range of the respective extent buffers to the ->dirty_pages iotree of the
transaction, and a stale transaction, in the unlocked state or higher,
will not flush dirty extent buffers anymore, therefore resulting in not
persisting the tree block and resource leaks (not cleaning the dirty_pages
iotree for example).
So do the following changes:
1) Return -EUCLEAN if we find a stale transaction;
2) Turn the fs into error state, with error -EUCLEAN, so that no
transaction can be committed, and generate a stack trace;
3) Combine both conditions into a single if statement, as both are related
and have the same error message;
4) Mark the check as unlikely, since this is not expected to ever happen.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At btrfs_cow_block() we check if the block being COWed belongs to a root
that is being deleted and if so we log an error message. However this is
an unexpected case and it indicates a bug somewhere, so we should return
an error and abort the transaction. So change this in the following ways:
1) Abort the transaction with -EUCLEAN, so that if the issue ever happens
it can easily be noticed;
2) Change the logged message level from error to critical, and change the
message itself to print the block's logical address and the ID of the
root;
3) Return -EUCLEAN to the caller;
4) As this is an unexpected scenario, that should never happen, mark the
check as unlikely, allowing the compiler to potentially generate better
code.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
At btrfs_cow_block() we have these checks to verify we are not using a
stale transaction (a past transaction with an unblocked state or higher),
and the only thing we do is to trigger a WARN with a message and a stack
trace. This however is a critical problem, highly unexpected and if it
happens it's most likely due to a bug, so we should error out and turn the
fs into error state so that such issue is much more easily noticed if it's
triggered.
The problem is critical because using such stale transaction will lead to
not persisting the extent buffer used for the COW operation, as allocating
a tree block adds the range of the respective extent buffer to the
->dirty_pages iotree of the transaction, and a stale transaction, in the
unlocked state or higher, will not flush dirty extent buffers anymore,
therefore resulting in not persisting the tree block and resource leaks
(not cleaning the dirty_pages iotree for example).
So do the following changes:
1) Return -EUCLEAN if we find a stale transaction;
2) Turn the fs into error state, with error -EUCLEAN, so that no
transaction can be committed, and generate a stack trace;
3) Combine both conditions into a single if statement, as both are related
and have the same error message;
4) Mark the check as unlikely, since this is not expected to ever happen.
Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Jens reported the following warnings from -Wmaybe-uninitialized recent
Linus' branch.
In file included from ./include/asm-generic/rwonce.h:26,
from ./arch/arm64/include/asm/rwonce.h:71,
from ./include/linux/compiler.h:246,
from ./include/linux/export.h:5,
from ./include/linux/linkage.h:7,
from ./include/linux/kernel.h:17,
from fs/btrfs/ioctl.c:6:
In function ‘instrument_copy_from_user_before’,
inlined from ‘_copy_from_user’ at ./include/linux/uaccess.h:148:3,
inlined from ‘copy_from_user’ at ./include/linux/uaccess.h:183:7,
inlined from ‘btrfs_ioctl_space_info’ at fs/btrfs/ioctl.c:2999:6,
inlined from ‘btrfs_ioctl’ at fs/btrfs/ioctl.c:4616:10:
./include/linux/kasan-checks.h:38:27: warning: ‘space_args’ may be used
uninitialized [-Wmaybe-uninitialized]
38 | #define kasan_check_write __kasan_check_write
./include/linux/instrumented.h:129:9: note: in expansion of macro
‘kasan_check_write’
129 | kasan_check_write(to, n);
| ^~~~~~~~~~~~~~~~~
./include/linux/kasan-checks.h: In function ‘btrfs_ioctl’:
./include/linux/kasan-checks.h:20:6: note: by argument 1 of type ‘const
volatile void *’ to ‘__kasan_check_write’ declared here
20 | bool __kasan_check_write(const volatile void *p, unsigned int
size);
| ^~~~~~~~~~~~~~~~~~~
fs/btrfs/ioctl.c:2981:39: note: ‘space_args’ declared here
2981 | struct btrfs_ioctl_space_args space_args;
| ^~~~~~~~~~
In function ‘instrument_copy_from_user_before’,
inlined from ‘_copy_from_user’ at ./include/linux/uaccess.h:148:3,
inlined from ‘copy_from_user’ at ./include/linux/uaccess.h:183:7,
inlined from ‘_btrfs_ioctl_send’ at fs/btrfs/ioctl.c:4343:9,
inlined from ‘btrfs_ioctl’ at fs/btrfs/ioctl.c:4658:10:
./include/linux/kasan-checks.h:38:27: warning: ‘args32’ may be used
uninitialized [-Wmaybe-uninitialized]
38 | #define kasan_check_write __kasan_check_write
./include/linux/instrumented.h:129:9: note: in expansion of macro
‘kasan_check_write’
129 | kasan_check_write(to, n);
| ^~~~~~~~~~~~~~~~~
./include/linux/kasan-checks.h: In function ‘btrfs_ioctl’:
./include/linux/kasan-checks.h:20:6: note: by argument 1 of type ‘const
volatile void *’ to ‘__kasan_check_write’ declared here
20 | bool __kasan_check_write(const volatile void *p, unsigned int
size);
| ^~~~~~~~~~~~~~~~~~~
fs/btrfs/ioctl.c:4341:49: note: ‘args32’ declared here
4341 | struct btrfs_ioctl_send_args_32 args32;
| ^~~~~~
This was due to his config options and having KASAN turned on,
which adds some extra checks around copy_from_user(), which then
triggered the -Wmaybe-uninitialized checker for these cases.
Fix the warnings by initializing the different structs we're copying
into.
Reported-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The One Mix 2S is a mini laptop with a 1200x1920 portrait screen
mounted in a landscape oriented clamshell case. Because of the too
generic DMI strings this entry is also doing bios-date matching.
After deleting an interface address in fib_del_ifaddr(), the function
scans the fib_info list for stray entries and calls fib_flush() and
fib_table_flush(). Then the stray entries will be deleted silently and no
RTM_DELROUTE notification will be sent.
This lack of notification can make routing daemons, or monitor like
`ip monitor route` miss the routing changes. e.g.
+ ip link add dummy1 type dummy
+ ip link add dummy2 type dummy
+ ip link set dummy1 up
+ ip link set dummy2 up
+ ip addr add 192.168.5.5/24 dev dummy1
+ ip route add 7.7.7.0/24 dev dummy2 src 192.168.5.5
+ ip -4 route
7.7.7.0/24 dev dummy2 scope link src 192.168.5.5
192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
+ ip monitor route
+ ip addr del 192.168.5.5/24 dev dummy1
Deleted 192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
Deleted broadcast 192.168.5.255 dev dummy1 table local proto kernel scope link src 192.168.5.5
Deleted local 192.168.5.5 dev dummy1 table local proto kernel scope host src 192.168.5.5
As Ido reminded, fib_table_flush() isn't only called when an address is
deleted, but also when an interface is deleted or put down. The lack of
notification in these cases is deliberate. And commit 7c6bb7d2faaf
("net/ipv6: Add knob to skip DELROUTE message on device down") introduced
a sysctl to make IPv6 behave like IPv4 in this regard. So we can't send
the route delete notify blindly in fib_table_flush().
To fix this issue, let's add a new flag in "struct fib_info" to track the
deleted prefer source address routes, and only send notify for them.
After update:
+ ip monitor route
+ ip addr del 192.168.5.5/24 dev dummy1
Deleted 192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
Deleted broadcast 192.168.5.255 dev dummy1 table local proto kernel scope link src 192.168.5.5
Deleted local 192.168.5.5 dev dummy1 table local proto kernel scope host src 192.168.5.5
Deleted 7.7.7.0/24 dev dummy2 scope link src 192.168.5.5
Suggested-by: Thomas Haller <thaller@redhat.com> Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20230922075508.848925-1-liuhangbin@gmail.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In the pathological case of building sky2 with 16k PAGE_SIZE, the
frag_addr[] array would never be used, so the original code was correct
that size should be 0. But the compiler now gets upset with 0 size arrays
in places where it hasn't eliminated the code that might access such an
array (it can't figure out that in this case an rx skb with fragments
would never be created). To keep the compiler happy, make sure there is
at least 1 frag_addr in struct rx_ring_info:
In file included from include/linux/skbuff.h:28,
from include/net/net_namespace.h:43,
from include/linux/netdevice.h:38,
from drivers/net/ethernet/marvell/sky2.c:18:
drivers/net/ethernet/marvell/sky2.c: In function 'sky2_rx_unmap_skb':
include/linux/dma-mapping.h:416:36: warning: array subscript i is outside array bounds of 'dma_addr_t[0]' {aka 'long long unsigned int[]'} [-Warray-bounds=]
416 | #define dma_unmap_page(d, a, s, r) dma_unmap_page_attrs(d, a, s, r, 0)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/marvell/sky2.c:1257:17: note: in expansion of macro 'dma_unmap_page'
1257 | dma_unmap_page(&pdev->dev, re->frag_addr[i],
| ^~~~~~~~~~~~~~
In file included from drivers/net/ethernet/marvell/sky2.c:41:
drivers/net/ethernet/marvell/sky2.h:2198:25: note: while referencing 'frag_addr'
2198 | dma_addr_t frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
| ^~~~~~~~~
With CONFIG_PAGE_SIZE_16KB=y, PAGE_SHIFT == 14, so:
#define ETH_JUMBO_MTU 9000
causes "ETH_JUMBO_MTU >> PAGE_SHIFT" to be 0. Use "?: 1" to solve this build warning.
Cc: Mirko Lindner <mlindner@marvell.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: Eric Dumazet <edumazet@google.com> Cc: Jakub Kicinski <kuba@kernel.org> Cc: Paolo Abeni <pabeni@redhat.com> Cc: netdev@vger.kernel.org Reported-by: kernel test robot <lkp@intel.com> Closes: https://lore.kernel.org/oe-kbuild-all/202309191958.UBw1cjXk-lkp@intel.com/ Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com> Signed-off-by: Kees Cook <keescook@chromium.org> Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the structure is not initialized then boolean types might be copied
into the tracing data without being initialised. This causes data from
the stack to leak into the trace and also triggers a UBSAN failure which
can easily be avoided here.
Lower layer device driver stop/wake TX by calling ieee80211_stop_queue()/
ieee80211_wake_queue() while hw scan. Sometimes hw scan and PTK rekey are
running in parallel, when M4 sent from wpa_supplicant arrive while the TX
queue is stopped, then the M4 will pending send, and then new key install
from wpa_supplicant. After TX queue wake up by lower layer device driver,
the M4 will be dropped by below call stack.
When key install started, the current key flag is set KEY_FLAG_TAINTED in
ieee80211_pairwise_rekey(), and then mac80211 wait key install complete by
lower layer device driver. Meanwhile ieee80211_tx_h_select_key() will return
TX_DROP for the M4 in step 12 below, and then ieee80211_free_txskb() called
by ieee80211_tx_dequeue(), so the M4 will not send and free, then the rekey
process failed becaue AP not receive M4. Please see details in steps below.
There are a interval between KEY_FLAG_TAINTED set for current key flag and
install key complete by lower layer device driver, the KEY_FLAG_TAINTED is
set in this interval, all packet including M4 will be dropped in this
interval, the interval is step 8~13 as below.
issue steps:
TX thread install key thread
1. stop_queue -idle-
2. sending M4 -idle-
3. M4 pending -idle-
4. -idle- starting install key from wpa_supplicant
5. -idle- =>ieee80211_key_replace()
6. -idle- =>ieee80211_pairwise_rekey() and set
currently key->flags |= KEY_FLAG_TAINTED
7. -idle- =>ieee80211_key_enable_hw_accel()
8. -idle- =>drv_set_key() and waiting key install
complete from lower layer device driver
9. wake_queue -waiting state-
10. re-sending M4 -waiting state-
11. =>ieee80211_tx_h_select_key() -waiting state-
12. drop M4 by KEY_FLAG_TAINTED -waiting state-
13. -idle- install key complete with success/fail
success: clear flag KEY_FLAG_TAINTED
fail: start disconnect
Hence add check in step 11 above to allow the EAPOL send out in the
interval. If lower layer device driver use the old key/cipher to encrypt
the M4, then AP received/decrypt M4 correctly, after M4 send out, lower
layer device driver install the new key/cipher to hardware and return
success.
If lower layer device driver use new key/cipher to send the M4, then AP
will/should drop the M4, then it is same result with this issue, AP will/
should kick out station as well as this issue.
When the scan request includes a non broadcast BSSID, when adding the
scan parameters for 6GHz collocated scanning, do not include entries
that do not match the given BSSID.
net/bluetooth/hci_core.c: In function ‘hci_register_dev’:
net/bluetooth/hci_core.c:2620:54: warning: ‘%d’ directive output may
be truncated writing between 1 and 10 bytes into a region of size 5
[-Wformat-truncation=]
2620 | snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
| ^~
net/bluetooth/hci_core.c:2620:50: note: directive argument in the range
[0, 2147483647]
2620 | snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
| ^~~~~~~
net/bluetooth/hci_core.c:2620:9: note: ‘snprintf’ output between 5 and
14 bytes into a destination of size 8
2620 | snprintf(hdev->name, sizeof(hdev->name), "hci%d", id);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While executing the Android 13 CTS Verifier Secure Server test on a
ChromeOS device, it was observed that the Bluetooth host initiates
authentication for an RFCOMM connection after SSP completes.
When this happens, some Intel Bluetooth controllers, like AC9560, would
disconnect with "Connection Rejected due to Security Reasons (0x0e)".
Historically, BlueZ did not mandate this authentication while an
authenticated combination key was already in use for the connection.
This behavior was changed since commit 7b5a9241b780
("Bluetooth: Introduce requirements for security level 4").
So, this patch addresses the aforementioned disconnection issue by
restoring the previous behavior.
Signed-off-by: Ying Hsu <yinghsu@chromium.org> Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There is a slab-out-of-bounds Write bug in hid-holtek-kbd driver.
The problem is the driver assumes the device must have an input
but some malicious devices violate this assumption.
Fix this by checking hid_device's input is non-empty before its usage.
Signed-off-by: Ma Ke <make_ruc2021@163.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Sasha Levin <sashal@kernel.org>
Debugging indicates that nothing else is clearing the info->flags,
so some frames were flagged as ACKed when they should not be.
Explicitly clear the ack flag to ensure this does not happen.
When kernel is compiled without preemption, the eval_map_work_func()
(which calls trace_event_eval_update()) will not be preempted up to its
complete execution. This can actually cause a problem since if another
CPU call stop_machine(), the call will have to wait for the
eval_map_work_func() function to finish executing in the workqueue
before being able to be scheduled. This problem was observe on a SMP
system at boot time, when the CPU calling the initcalls executed
clocksource_done_booting() which in the end calls stop_machine(). We
observed a 1 second delay because one CPU was executing
eval_map_work_func() and was not preempted by the stop_machine() task.
Adding a call to cond_resched() in trace_event_eval_update() allows
other tasks to be executed and thus continue working asynchronously
like before without blocking any pending task at boot time.
The 6 bytes length of the tries_buf string in ata_eh_link_report() is
too short and results in a gcc compilation warning with W-!:
drivers/ata/libata-eh.c: In function ‘ata_eh_link_report’:
drivers/ata/libata-eh.c:2371:59: warning: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size 4 [-Wformat-truncation=]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~
drivers/ata/libata-eh.c:2371:56: note: directive argument in the range [-2147483648, 4]
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~
drivers/ata/libata-eh.c:2371:17: note: ‘snprintf’ output between 4 and 14 bytes into a destination of size 6
2371 | snprintf(tries_buf, sizeof(tries_buf), " t%d",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2372 | ap->eh_tries);
| ~~~~~~~~~~~~~
Avoid this warning by increasing the string size to 16B.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The 24 bytes length allocated to the ncq_desc string in
ata_dev_config_lba() for ata_dev_config_ncq() to use is too short,
causing the following gcc compilation warnings when compiling with W=1:
drivers/ata/libata-core.c: In function ‘ata_dev_configure’:
drivers/ata/libata-core.c:2378:56: warning: ‘%d’ directive output may be truncated writing between 1 and 2 bytes into a region of size between 1 and 11 [-Wformat-truncation=]
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~
In function ‘ata_dev_config_ncq’,
inlined from ‘ata_dev_config_lba’ at drivers/ata/libata-core.c:2649:8,
inlined from ‘ata_dev_configure’ at drivers/ata/libata-core.c:2952:9:
drivers/ata/libata-core.c:2378:41: note: directive argument in the range [1, 32]
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~~~~~~~~~~~~~~~~~~~~
drivers/ata/libata-core.c:2378:17: note: ‘snprintf’ output between 16 and 31 bytes into a destination of size 24
2378 | snprintf(desc, desc_sz, "NCQ (depth %d/%d)%s", hdepth,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
2379 | ddepth, aa_desc);
| ~~~~~~~~~~~~~~~~
Avoid these warnings and the potential truncation by changing the size
of the ncq_desc string to 32 characters.
Signed-off-by: Damien Le Moal <dlemoal@kernel.org> Reviewed-by: Hannes Reinecke <hare@suse.de> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
As timbgpio_irq_enable()/timbgpio_irq_disable() callback could be
executed under irq context, it could introduce double locks on
&tgpio->lock if it preempts other execution units requiring
the same locks.
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
To prevent the potential deadlock, the patch uses spin_lock_irqsave()
on &tgpio->lock inside timbgpio_gpio_set() to prevent the possible
deadlock scenario.
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com> Reviewed-by: Andy Shevchenko <andy@kernel.org> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Nathan reported that he was seeing the new warning in
setattr_copy_mgtime pop when starting podman containers. Overlayfs is
trying to set the atime and mtime via notify_change without also
setting the ctime.
POSIX states that when the atime and mtime are updated via utimes() that
we must also update the ctime to the current time. The situation with
overlayfs copy-up is analogies, so add ATTR_CTIME to the bitmask.
notify_change will fill in the value.
Reported-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Jeff Layton <jlayton@kernel.org> Tested-by: Nathan Chancellor <nathan@kernel.org> Acked-by: Christian Brauner <brauner@kernel.org> Acked-by: Amir Goldstein <amir73il@gmail.com>
Message-Id: <20230913-ctime-v1-1-c6bc509cbc27@kernel.org> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
I2C_CLASS_DEPRECATED is a flag and not an actual class.
There's nothing speaking against both, parent and child, having
I2C_CLASS_DEPRECATED set. Therefore exclude it from the check.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Peter Rosin <peda@axentia.se> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Jens reported a compiler warning when using
CONFIG_CC_OPTIMIZE_FOR_SIZE=y that looks like this
fs/btrfs/tree-log.c: In function ‘btrfs_log_prealloc_extents’:
fs/btrfs/tree-log.c:4828:23: warning: ‘start_slot’ may be used
uninitialized [-Wmaybe-uninitialized]
4828 | ret = copy_items(trans, inode, dst_path, path,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
4829 | start_slot, ins_nr, 1, 0);
| ~~~~~~~~~~~~~~~~~~~~~~~~~
fs/btrfs/tree-log.c:4725:13: note: ‘start_slot’ was declared here
4725 | int start_slot;
| ^~~~~~~~~~
The compiler is incorrect, as we only use this code when ins_len > 0,
and when ins_len > 0 we have start_slot properly initialized. However
we generally find the -Wmaybe-uninitialized warnings valuable, so
initialize start_slot to get rid of the warning.
Reported-by: Jens Axboe <axboe@kernel.dk> Tested-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Josef Bacik <josef@toxicpanda.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When running a delayed tree reference, if we find a ref count different
from 1, we return -EIO. This isn't an IO error, as it indicates either a
bug in the delayed refs code or a memory corruption, so change the error
code from -EIO to -EUCLEAN. Also tag the branch as 'unlikely' as this is
not expected to ever happen, and change the error message to print the
tree block's bytenr without the parenthesis (and there was a missing space
between the 'block' word and the opening parenthesis), for consistency as
that's the style we used everywhere else.
Reviewed-by: Josef Bacik <josef@toxicpanda.com> Signed-off-by: Filipe Manana <fdmanana@suse.com> Reviewed-by: David Sterba <dsterba@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When writing back an inode and performing an fsync on it concurrently, a
deadlock issue may arise as shown below. In each writeback iteration, a
clean inode is requeued to the wb->b_dirty queue due to non-zero
pages_skipped, without anything actually being written. This causes an
infinite loop and prevents the plug from being flushed, resulting in a
deadlock. We now avoid requeuing the clean inode to prevent this issue.
wb_writeback fsync (inode-Y)
blk_start_plug(&plug)
for (;;) {
iter i-1: some reqs with page-X added into plug->mq_list // f2fs node page-X with PG_writeback
filemap_fdatawrite
__filemap_fdatawrite_range // write inode-Y with sync_mode WB_SYNC_ALL
do_writepages
f2fs_write_data_pages
__f2fs_write_data_pages // wb_sync_req[DATA]++ for WB_SYNC_ALL
f2fs_write_cache_pages
f2fs_write_single_data_page
f2fs_do_write_data_page
f2fs_outplace_write_data
f2fs_update_data_blkaddr
f2fs_wait_on_page_writeback
wait_on_page_writeback // wait for f2fs node page-X
iter i:
progress = __writeback_inodes_wb(wb, work)
. writeback_sb_inodes
. __writeback_single_inode // write inode-Y with sync_mode WB_SYNC_NONE
. . do_writepages
. . f2fs_write_data_pages
. . . __f2fs_write_data_pages // skip writepages due to (wb_sync_req[DATA]>0)
. . . wbc->pages_skipped += get_dirty_pages(inode) // wbc->pages_skipped = 1
. if (!(inode->i_state & I_DIRTY_ALL)) // i_state = I_SYNC | I_SYNC_QUEUED
. total_wrote++; // total_wrote = 1
. requeue_inode // requeue inode-Y to wb->b_dirty queue due to non-zero pages_skipped
if (progress) // progress = 1
continue;
iter i+1:
queue_io
// similar process with iter i, infinite for-loop !
}
blk_finish_plug(&plug) // flush plug won't be called
Signed-off-by: Chunhai Guo <guochunhai@vivo.com> Reviewed-by: Jan Kara <jack@suse.cz>
Message-Id: <20230916045131.957929-1-guochunhai@vivo.com> Signed-off-by: Christian Brauner <brauner@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
On mapphone devices we may get lots of noise on the micro-USB port in debug
uart mode until the phy-cpcap-usb driver probes. Let's limit the noise by
using overrun-throttle-ms.
Note that there is also a related separate issue where the charger cable
connected may cause random sysrq requests until phy-cpcap-usb probes that
still remains.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com> Cc: Carl Philipp Klemm <philipp@uvos.xyz> Cc: Merlijn Wajer <merlijn@wizzup.org> Cc: Pavel Machek <pavel@ucw.cz> Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
check for proper open/unlink operation
nfsjunk files before unlink:
-rwxr-xr-x 1 root root 0 9월 25 11:03 ./nfs2y8Jm9
./nfs2y8Jm9 open; unlink ret = 0
nfsjunk files after unlink:
-rwxr-xr-x 1 root root 0 9월 25 11:03 ./nfs2y8Jm9
data compare ok
nfsjunk files after close:
ls: cannot access './nfs2y8Jm9': No such file or directory
special tests failed
Cthon expect to second unlink failure when file is already unlinked.
ksmbd can not allow to open file if flags of ksmbd inode is set with
S_DEL_ON_CLS flags.
Cc: stable@vger.kernel.org Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the execution order is (1)->(2)->(3), it will crash. Therefore, in
the function nfp_fl_ct_del_flow, nf_flow_table_offload_del_cb needs to
be executed synchronously.
At the same time, in order to solve the deadlock problem and the problem
of rtnl_lock sometimes failing, replace rtnl_lock with the private
nfp_fl_lock.
Fixes: 7cc93d888df7 ("nfp: flower-ct: remove callback delete deadlock") Cc: stable@vger.kernel.org Signed-off-by: Yanguo Li <yanguo.li@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Our current route lookups (mctp_route_lookup and mctp_route_lookup_null)
traverse the net's route list without the RCU read lock held. This means
the route lookup is subject to preemption, resulting in an potential
grace period expiry, and so an eventual kfree() while we still have the
route pointer.
Add the proper read-side critical section locks around the route
lookups, preventing premption and a possible parallel kfree.
The remaining net->mctp.routes accesses are already under a
rcu_read_lock, or protected by the RTNL for updates.
Based on an analysis from Sili Luo <rootlab@huawei.com>, where
introducing a delay in the route lookup could cause a UAF on
simultaneous sendmsg() and route deletion.
Reported-by: Sili Luo <rootlab@huawei.com> Fixes: 889b7da23abf ("mctp: Add initial routing framework") Cc: stable@vger.kernel.org Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Reviewed-by: Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/29c4b0e67dc1bf3571df3982de87df90cae9b631.1696837310.git.jk@codeconstruct.com.au Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We may need to receive packets addressed to the null EID (==0), but
addressed to us at the physical layer.
This change adds a lookup for local routes when we see a packet
addressed to EID 0, and a local phys address.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au> Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5093bbfc10ab ("mctp: perform route lookups under a RCU read-side lock") Signed-off-by: Sasha Levin <sashal@kernel.org>
The problem is in ret_from_syscall where the check for
icache_44x_need_flush is done. When the flush is needed the code jumps
out-of-line to do the flush, and then intends to jump back to continue
the syscall return.
However the branch back to label 1b doesn't return to the correct
location, instead branching back just prior to the return to userspace,
causing bogus register values to be used by the rfi.
The breakage was introduced by commit 6f76a01173cc
("powerpc/syscall: implement system call entry/exit logic in C for PPC32") which
inadvertently removed the "1" label and reused it elsewhere.
Fix it by adding named local labels in the correct locations. Note that
the return label needs to be outside the ifdef so that CONFIG_PPC_47x=n
compiles.
When interrupt and syscall entries where converted to C, KUEP locking
and unlocking was also converted. It improved performance by unrolling
the loop, and allowed easily implementing boot time deactivation of
KUEP.
However, null_syscall selftest shows that KUEP is still heavy
(361 cycles with KUEP, 212 cycles without).
A way to improve more is to group 'mtsr's together, instead of
repeating 'addi' + 'mtsr' several times.
In order to do that, more registers need to be available. In C, GCC
will always be able to provide the requested number of registers, but
at the cost of saving some data on the stack, which is counter
performant here.
So let's do it in assembly, when we have full control of which
register can be used. It also has the advantage of locking earlier
and unlocking later and it helps GCC generating less tricky code.
The only drawback is to make boot time deactivation less straight
forward and require 'hand' instruction patching.
Group 'mtsr's by 4.
With this change, null_syscall selftest reports 336 cycles. Without
the change it was 361 cycles, that's a 7% reduction.
The driver might pull connectors which weren't submitted by
user-space into the atomic state. For instance,
intel_dp_mst_atomic_master_trans_check() pulls in connectors
sharing the same DP-MST stream. However, if the connector is
unregistered, this later fails with:
[ 559.425658] i915 0000:00:02.0: [drm:drm_atomic_helper_check_modeset] [CONNECTOR:378:DP-7] is not registered
Skip the unregistered connector check to allow user-space to turn
off connectors one-by-one.
See this wlroots issue:
https://gitlab.freedesktop.org/wlroots/wlroots/-/issues/3407
We found that a panic can occur when a vsyscall is made while LBR sampling
is active. If the vsyscall is interrupted (NMI) for perf sampling, this
call sequence can occur (most recent at top):
Within __insn_get_emulate_prefix() at frame 0, a macro is called:
peek_nbyte_next(insn_byte_t, insn, i)
Within this macro, this dereference occurs:
(insn)->next_byte
Inspecting registers at this point, the value of the next_byte field is the
address of the vsyscall made, for example the location of the vsyscall
version of gettimeofday() at 0xffffffffff600000. The access to an address
in the vsyscall region will trigger an oops due to an unhandled page fault.
To fix the bug, filtering for vsyscalls can be done when
determining the branch type. This patch will return
a "none" branch if a kernel address if found to lie in the
vsyscall region.
Commit 3e702ff6d1ea ("perf/x86: Add LBR software filter support for Intel
CPUs") introduces a software branch filter which complements the hardware
branch filter and adds an x86 branch classifier.
Move the branch classifier to arch/x86/events/ so that it can be utilized
by other vendors for branch record filtering.
This expands generic branch type classification by adding two more entries
there in i.e irq and exception return. Also updates the x86 implementation
to process X86_BR_IRET and X86_BR_IRQ records as appropriate. This changes
branch types reported to user space on x86 platform but it should not be a
problem. The possible scenarios and impacts are enumerated here.
cros_ec_sensors_push_data() reads `indio_dev->active_scan_mask` and
calls iio_push_to_buffers_with_timestamp() without making sure the
`indio_dev` stays in buffer mode. There is a race if `indio_dev` exits
buffer mode right before cros_ec_sensors_push_data() accesses them.
An use-after-free on `indio_dev->active_scan_mask` was observed. The
call trace:
[...]
_find_next_bit
cros_ec_sensors_push_data
cros_ec_sensorhub_event
blocking_notifier_call_chain
cros_ec_irq_thread
It was caused by a race condition: one thread just freed
`active_scan_mask` at [1]; while another thread tried to access the
memory at [2].
Fix it by calling iio_device_claim_buffer_mode() to ensure the
`indio_dev` can't exit buffer mode during cros_ec_sensors_push_data().
These APIs are analogous to iio_device_claim_direct_mode() and
iio_device_release_direct_mode() but, as the name suggests, with the
logic flipped. While this looks odd enough, it will have at least two
users (in following changes) and it will be important to move the IIO
mlock to the private struct.
Signed-off-by: Nuno Sá <nuno.sa@analog.com> Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20221012151620.1725215-2-nuno.sa@analog.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 7771c8c80d62 ("iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()") Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to later move this variable within the opaque structure, let's
create a helper for accessing it in read-only mode. This helper will be
exposed to device drivers and kept accessible for the few that could need
it. The write access to this variable however should be fully reserved to
the core so in a second step we will hide this variable into the opaque
structure.
Cc: Eugen Hristev <eugen.hristev@microchip.com> Cc: Nicolas Ferre <nicolas.ferre@microchip.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Cc: Ludovic Desroches <ludovic.desroches@microchip.com> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20220207143840.707510-11-miquel.raynal@bootlin.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 7771c8c80d62 ("iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()") Signed-off-by: Sasha Levin <sashal@kernel.org>
As we are going to hide the currentmode inside the opaque structure,
this helper would soon need to call a non-inline function which would
simply drop the benefit of having the helper defined inline in a header.
One alternative is to move this helper in the core as there is no more
interest in defining it inline in a header. We will pay the minor cost
either way.
Let's do like the iio_device_id() helper which also refers to the opaque
structure and gets defined in the core.
Suggested-by: Jonathan Cameron <jic23@kernel.org> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Link: https://lore.kernel.org/r/20220207143840.707510-10-miquel.raynal@bootlin.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Stable-dep-of: 7771c8c80d62 ("iio: cros_ec: fix an use-after-free in cros_ec_sensors_push_data()") Signed-off-by: Sasha Levin <sashal@kernel.org>
We now get errors on system suspend if no_console_suspend is set as
reported by Thomas. The errors started with commit 20a41a62618d ("serial:
8250_omap: Use force_suspend and resume for system suspend").
Let's fix the issue by checking for console_suspend_enabled in the system
suspend and resume path.
Note that with this fix the checks for console_suspend_enabled in
omap8250_runtime_suspend() become useless. We now keep runtime PM usage
count for an attached kernel console starting with commit bedb404e91bb
("serial: 8250_port: Don't use power management for kernel console").
Fixes: 20a41a62618d ("serial: 8250_omap: Use force_suspend and resume for system suspend") Cc: stable <stable@kernel.org> Cc: Udit Kumar <u-kumar1@ti.com> Reported-by: Thomas Richard <thomas.richard@bootlin.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Tested-by: Thomas Richard <thomas.richard@bootlin.com> Reviewed-by: Dhruva Gole <d-gole@ti.com> Link: https://lore.kernel.org/r/20230926061319.15140-1-tony@atomide.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
We must idle the uart only after serial8250_unregister_port(). Otherwise
unbinding the uart via sysfs while doing cat on the port produces an
imprecise external abort:
mem_serial_in from omap_8250_pm+0x44/0xf4
omap_8250_pm from uart_hangup+0xe0/0x194
uart_hangup from __tty_hangup.part.0+0x37c/0x3a8
__tty_hangup.part.0 from uart_remove_one_port+0x9c/0x22c
uart_remove_one_port from serial8250_unregister_port+0x60/0xe8
serial8250_unregister_port from omap8250_remove+0x6c/0xd0
omap8250_remove from platform_remove+0x28/0x54
Turns out the driver needs to have runtime PM functional before the
driver probe calls serial8250_register_8250_port(). And it needs
runtime PM after driver remove calls serial8250_unregister_port().
On probe, we need to read registers before registering the port in
omap_serial_fill_features_erratas(). We do that with custom uart_read()
already.
On remove, after serial8250_unregister_port(), we need to write to the
uart registers to idle the device. Let's add a custom uart_write() for
that.
Currently the uart register access depends on port->membase to be
initialized, which won't work after serial8250_unregister_port().
Let's use priv->membase instead, and use it for runtime PM related
functions to remove the dependency to port->membase for early and
late register access.
Note that during use, we need to check for a valid port in the runtime PM
related functions. This is needed for the optional wakeup configuration.
We now need to set the drvdata a bit earlier so it's available for the
runtime PM functions.
With the port checks in runtime PM functions, the old checks for priv in
omap8250_runtime_suspend() and omap8250_runtime_resume() functions are no
longer needed and are removed.
Device flags are displayed incorrectly:
1) The comparison (i == F_FLOW_SEQ) is always false, because F_FLOW_SEQ
is equal to (1 << FLOW_SEQ_SHIFT) == 2048, and the maximum value
of the 'i' variable is (NR_PKT_FLAG - 1) == 17. It should be compared
with FLOW_SEQ_SHIFT.
2) Similarly to the F_IPSEC flag.
3) Also add spaces to the print end of the string literal "spi:%u"
to prevent the output from merging with the flag that follows.
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with SVACE.
Fixes: 99c6d3d20d62 ("pktgen: Remove brute-force printing of flags") Signed-off-by: Gavrilov Ilia <Ilia.Gavrilov@infotecs.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nf_tables_abort_release() path calls nft_set_elem_destroy() for
NFT_MSG_NEWSETELEM which releases the element, however, a reference to
the element still remains in the working copy.
Fixes: ebd032fa8818 ("netfilter: nf_tables: do not remove elements if set backend implements .abort") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pipapo set backend maintains two copies of the datastructure, removing
the elements from the copy that is going to be discarded slows down
the abort path significantly, from several minutes to few seconds after
this patch.
This allows to remove an expired element which is not possible in other
existing set backends, this is more noticeable if gc-interval is high so
expired elements remain in the tree. On-demand gc also does not help in
this case, because this is delete element path. Return NULL if element
has expired.
In file included from include/trace/define_trace.h:102,
from include/trace/events/neigh.h:255,
from net/core/net-traces.c:51:
include/trace/events/neigh.h: In function ‘trace_event_raw_event_neigh_create’:
include/trace/events/neigh.h:42:34: error: variable ‘pin6’ set but not used [-Werror=unused-but-set-variable]
42 | struct in6_addr *pin6;
| ^~~~
include/trace/trace_events.h:402:11: note: in definition of macro ‘DECLARE_EVENT_CLASS’
402 | { assign; } \
| ^~~~~~
include/trace/trace_events.h:44:30: note: in expansion of macro ‘PARAMS’
44 | PARAMS(assign), \
| ^~~~~~
include/trace/events/neigh.h:23:1: note: in expansion of macro ‘TRACE_EVENT’
23 | TRACE_EVENT(neigh_create,
| ^~~~~~~~~~~
include/trace/events/neigh.h:41:9: note: in expansion of macro ‘TP_fast_assign’
41 | TP_fast_assign(
| ^~~~~~~~~~~~~~
In file included from include/trace/define_trace.h:103,
from include/trace/events/neigh.h:255,
from net/core/net-traces.c:51:
include/trace/events/neigh.h: In function ‘perf_trace_neigh_create’:
include/trace/events/neigh.h:42:34: error: variable ‘pin6’ set but not used [-Werror=unused-but-set-variable]
42 | struct in6_addr *pin6;
| ^~~~
include/trace/perf.h:51:11: note: in definition of macro ‘DECLARE_EVENT_CLASS’
51 | { assign; } \
| ^~~~~~
include/trace/trace_events.h:44:30: note: in expansion of macro ‘PARAMS’
44 | PARAMS(assign), \
| ^~~~~~
include/trace/events/neigh.h:23:1: note: in expansion of macro ‘TRACE_EVENT’
23 | TRACE_EVENT(neigh_create,
| ^~~~~~~~~~~
include/trace/events/neigh.h:41:9: note: in expansion of macro ‘TP_fast_assign’
41 | TP_fast_assign(
| ^~~~~~~~~~~~~~
Indeed, the variable pin6 is declared and initialized unconditionally,
while it is only used and needlessly re-initialized when support for
IPv6 is enabled.
Fix this by dropping the unused variable initialization, and moving the
variable declaration inside the existing section protected by a check
for CONFIG_IPV6.
Fixes: fc651001d2c5ca4f ("neighbor: Add tracepoint to __neigh_create") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Simon Horman <horms@kernel.org> # build-tested Reviewed-by: David Ahern <dsahern@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Theune says:
I upgraded from 6.1.38 to 6.1.55 this morning and it broke my traffic shaping script,
leaving me with a non-functional uplink on a remote router.
A 'rt' curve cannot be used as a inner curve (parent class), but we were
allowing such configurations since the qdisc was introduced. Such
configurations would trigger a UAF as Budimir explains:
The parent will have vttree_insert() called on it in init_vf(),
but will not have vttree_remove() called on it in update_vf()
because it does not have the HFSC_FSC flag set.
The qdisc always assumes that inner classes have the HFSC_FSC flag set.
This is by design as it doesn't make sense 'qdisc wise' for an 'rt'
curve to be an inner curve.
Budimir's original patch disallows users to add classes with a 'rt'
parent, but this is too strict as it breaks users that have been using
'rt' as a inner class. Another approach, taken by this patch, is to
upgrade the inner 'rt' into a 'sc', warning the user in the process.
It avoids the UAF reported by Budimir while also being more permissive
to bad scripts/users/code using 'rt' as a inner class.
Users checking the `tc class ls [...]` or `tc class get [...]` dumps would
observe the curve change and are potentially breaking with this change.
v1->v2: https://lore.kernel.org/all/20231013151057.2611860-1-pctammela@mojatatu.com/
- Correct 'Fixes' tag and merge with revert (Jakub)
Cc: Christian Theune <ct@flyingcircus.io> Cc: Budimir Markovic <markovicbudimir@gmail.com> Fixes: b3d26c5702c7 ("net/sched: sch_hfsc: Ensure inner classes have fsc curve") Signed-off-by: Pedro Tammela <pctammela@mojatatu.com> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Link: https://lore.kernel.org/r/20231017143602.3191556-1-pctammela@mojatatu.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 429e3d123d9a ("bonding: Fix extraction of ports from the packet
headers"), header offsets used to compute a hash in bond_xmit_hash() are
relative to skb->data and not skb->head. If the tail of the header buffer
of an skb really needs to be advanced and the operation is successful, the
pointer to the data must be returned (and not a pointer to the head of the
buffer).
Fixes: 429e3d123d9a ("bonding: Fix extraction of ports from the packet headers") Signed-off-by: Jiri Wiesner <jwiesner@suse.de> Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In bcm_sf2_mdio_register(), the class_find_device() will call get_device()
to increment reference count for priv->master_mii_bus->dev if
of_mdio_find_bus() succeeds. If mdiobus_alloc() or mdiobus_register()
fails, it will call get_device() twice without decrement reference count
for the device. And it is the same if bcm_sf2_mdio_register() succeeds but
fails in bcm_sf2_sw_probe(), or if bcm_sf2_sw_probe() succeeds. If the
reference count has not decremented to zero, the dev related resource will
not be freed.
So remove the get_device() in bcm_sf2_mdio_register(), and call
put_device() if mdiobus_alloc() or mdiobus_register() fails and in
bcm_sf2_mdio_unregister() to solve the issue.
And as Simon suggested, unwind from errors for bcm_sf2_mdio_register() and
just return 0 if it succeeds to make it cleaner.
The hardware provides the indexes of the first and the last available
queue and VF. From the indexes, the driver calculates the numbers of
queues and VFs. In theory, a faulty device might say the last index is
smaller than the first index. In that case, the driver's calculation
would underflow, it would attempt to write to non-existent registers
outside of the ioremapped range and crash.
I ran into this not by having a faulty device, but by an operator error.
I accidentally ran a QE test meant for i40e devices on an ice device.
The test used 'echo i40e > /sys/...ice PCI device.../driver_override',
bound the driver to the device and crashed in one of the wr32 calls in
i40e_clear_hw.
Add checks to prevent underflows in the calculations of num_queues and
num_vfs. With this fix, the wrong device probing reports errors and
returns a failure without crashing.
Fixes: 838d41d92a90 ("i40e: clear all queues and interrupts") Signed-off-by: Michal Schmidt <mschmidt@redhat.com> Reviewed-by: Simon Horman <horms@kernel.org> Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel) Link: https://lore.kernel.org/r/20231011233334.336092-2-jacob.e.keller@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 6759 Comm: kworker/u4:15 Not tainted 6.6.0-rc4-syzkaller-00029-gcbf3a2cb156a #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 09/06/2023
Workqueue: wg-kex-wg1 wg_packet_handshake_send_worker
Fixes: 436c3b66ec98 ("ipv4: Invalidate nexthop cache nh_saddr more correctly.") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Simon Horman <horms@kernel.org> Reviewed-by: David Ahern <dsahern@kernel.org> Link: https://lore.kernel.org/r/20231017192304.82626-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: fb7589a16216 ("tun: Add ability to create tun device with given index") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Willem de Bruijn <willemb@google.com> Acked-by: Jason Wang <jasowang@redhat.com> Link: https://lore.kernel.org/r/20231016180851.3560092-1-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log