If the offset equals the bv_len of the first registered bvec, then the
request does not include any of that first bvec. Skip it so that drivers
don't have to deal with a zero length bvec, which was observed to break
NVMe's PRP list creation.
Cc: stable@vger.kernel.org Fixes: bd11b3a391e3 ("io_uring: don't use iov_iter_advance() for fixed buffers") Signed-off-by: Keith Busch <kbusch@kernel.org> Link: https://lore.kernel.org/r/20231120221831.2646460-1-kbusch@meta.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm glue driver is overriding the interrupt trigger types
defined by firmware when requesting the wakeup interrupts during probe.
This can lead to a failure to map the DP/DM wakeup interrupts after a
probe deferral as the firmware defined trigger types do not match the
type used for the initial mapping:
irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
irq: type mismatch, failed to map hwirq-15 for interrupt-controller@b220000!
Fix this by not overriding the firmware provided trigger types when
requesting the wakeup interrupts.
The default mode, configurable by DT, shall be set before usb role switch
driver is registered. Otherwise there is a race between default mode
and mode set by usb role switch driver.
Fixes: 98ed256a4dbad ("usb: dwc3: Add support for role-switch-default-mode binding") Cc: stable <stable@kernel.org> Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com> Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20231025095110.2405281-1-alexander.stein@ew.tq-group.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dwc2_hc_n_intr() writes back INTMASK as read but evaluates it
with intmask applied. In stress testing this causes spurious
interrupts like this:
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 7 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:07 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 0 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_hc_chhltd_intr_dma: Channel 4 - ChHltd set, but reason is unknown
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: hcint 0x00000002, intsts 0x04600001
[Mon Aug 14 10:51:08 2023] dwc2 3f980000.usb: dwc2_update_urb_state_abn(): trimming xfer length
Applying INTMASK prevents this. The issue exists in all versions of the
driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com> Tested-by: Ivan Ivanov <ivan.ivanov@suse.com> Tested-by: Andrea della Porta <andrea.porta@suse.com> Link: https://lore.kernel.org/r/20231115144514.15248-1-oneukum@suse.com Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hard reset queued prior to error recovery (or) received during
error recovery will make TCPM to prematurely exit error recovery
sequence. Ignore hard resets received during error recovery (or)
port reset sequence.
```
[46505.459688] state change SNK_READY -> ERROR_RECOVERY [rev3 NONE_AMS]
[46505.459706] state change ERROR_RECOVERY -> PORT_RESET [rev3 NONE_AMS]
[46505.460433] disable vbus discharge ret:0
[46505.461226] Setting usb_comm capable false
[46505.467244] Setting voltage/current limit 0 mV 0 mA
[46505.467262] polarity 0
[46505.470695] Requesting mux state 0, usb-role 0, orientation 0
[46505.475621] cc:=0
[46505.476012] pending state change PORT_RESET -> PORT_RESET_WAIT_OFF @ 100 ms [rev3 NONE_AMS]
[46505.476020] Received hard reset
[46505.476024] state change PORT_RESET -> HARD_RESET_START [rev3 HARD_RESET]
```
Cc: stable@vger.kernel.org Fixes: f0690a25a140 ("staging: typec: USB Type-C Port Manager (tcpm)") Signed-off-by: Badhri Jagan Sridharan <badhri@google.com> Acked-by: Heikki Krogeus <heikki.krogerus@linux.intel.com> Reviewed-by: Guenter Roeck <linux@roeck-us.net> Link: https://lore.kernel.org/r/20231101021909.2962679-1-badhri@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interface 4 is used by for QMI interface in stock firmware of MF28D, the
router which uses MF290 modem. Free the interface up, to rebind it to
qmi_wwan driver.
The proper configuration is:
Interface mapping is:
0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI
L716-EU is a Fibocom module based on ZTE's V3E/V3T chipset.
Device creates multiple interfaces when connected to PC as follows:
- Network Interface: ECM or RNDIS (set by FW or AT Command)
- ttyUSB0: AT port
- ttyUSB1: Modem port
- ttyUSB2: AT2 port
- ttyUSB3: Trace port for log information
- ADB: ADB port for debugging. ("Driver=usbfs" when ADB server enabled)
Here are the outputs of lsusb and usb-devices:
$ ls /dev/ttyUSB*
/dev/ttyUSB0 /dev/ttyUSB1 /dev/ttyUSB2 /dev/ttyUSB3
The interrupt service routine registered for the gadget is a primary
handler which mask the interrupt source and a threaded handler which
handles the source of the interrupt. Since the threaded handler is
voluntary threaded, the IRQ-core does not disable bottom halves before
invoke the handler like it does for the forced-threaded handler.
Due to changes in networking it became visible that a network gadget's
completions handler may schedule a softirq which remains unprocessed.
The gadget's completion handler is usually invoked either in hard-IRQ or
soft-IRQ context. In this context it is enough to just raise the softirq
because the softirq itself will be handled once that context is left.
In the case of the voluntary threaded handler, there is nothing that
will process pending softirqs. Which means it remain queued until
another random interrupt (on this CPU) fires and handles it on its exit
path or another thread locks and unlocks a lock with the bh suffix.
Worst case is that the CPU goes idle and the NOHZ complains about
unhandled softirqs.
Disable bottom halves before acquiring the lock (and disabling
interrupts) and enable them after dropping the lock. This ensures that
any pending softirqs will handled right away.
cc: stable@vger.kernel.org Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver") Signed-off-by: Pawel Laszczak <pawell@cadence.com> Acked-by: Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20231108093125.224963-1-pawell@cadence.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The "counter = -4294967297" means that lock count is -1 and a write lock
is being attempted. Then, we found that there is a btree with a counter
of 1 in btree_cache_freeable.
We found that this is a bug in bch_sectors_dirty_init() when locking c->root:
(1). Thread X has locked c->root(A) write.
(2). Thread Y failed to lock c->root(A), waiting for the lock(c->root A).
(3). Thread X bch_btree_set_root() changes c->root from A to B.
(4). Thread X releases the lock(c->root A).
(5). Thread Y successfully locks c->root(A).
(6). Thread Y releases the lock(c->root B).
In SHOW(), the variable 'n' is of type 'size_t.' While there is a
conditional check to verify that 'n' is not equal to zero before
executing the 'do_div' macro, concerns arise regarding potential
division by zero error in 64-bit environments.
The concern arises when 'n' is 64 bits in size, greater than zero, and
the lower 32 bits of it are zeros. In such cases, the conditional check
passes because 'n' is non-zero, but the 'do_div' macro casts 'n' to
'uint32_t,' effectively truncating it to its lower 32 bits.
Consequently, the 'n' value becomes zero.
To fix this potential division by zero error and ensure precise
division handling, this commit replaces the 'do_div' macro with
div64_u64(). div64_u64() is designed to work with 64-bit operands,
guaranteeing that division is performed correctly.
This change enhances the robustness of the code, ensuring that division
operations yield accurate results in all scenarios, eliminating the
possibility of division by zero, and improving compatibility across
different 64-bit environments.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
In btree_gc_rewrite_node(), pointer 'n' is not checked after it returns
from btree_gc_rewrite_node(). There is potential possibility that 'n' is
a non NULL ERR_PTR(), referencing such error code is not permitted in
following code. Therefore a return value checking is necessary after 'n'
is back from btree_node_alloc_replacement().
Signed-off-by: Coly Li <colyli@suse.de> Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20231120052503.6122-3-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In delay_presuspend, we set the atomic variable may_delay and then stop
the timer and flush pending bios. The intention here is to prevent the
delay target from re-arming the timer again.
However, this test is racy. Suppose that one thread goes to delay_bio,
sees that dc->may_delay is one and proceeds; now, another thread executes
delay_presuspend, it sets dc->may_delay to zero, deletes the timer and
flushes pending bios. Then, the first thread continues and adds the bio to
delayed->list despite the fact that dc->may_delay is false.
Fix this bug by changing may_delay's type from atomic_t to bool and
only access it while holding the delayed_bios_lock mutex. Note that we
don't have to grab the mutex in delay_resume because there are no bios
in flight at this point.
When a VF is being exposed form the kernel, it should be marked as "slave"
before exposing to the user-mode. The VF is not usable without netvsc
running as master. The user-mode should never see a VF without the "slave"
flag.
This commit moves the code of setting the slave flag to the time before
VF is exposed to user-mode.
Cc: stable@vger.kernel.org Fixes: 0c195567a8f6 ("netvsc: transparent VF management") Signed-off-by: Long Li <longli@microsoft.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Acked-by: Dexuan Cui <decui@microsoft.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In dasd_profile_start() the amount of requests on the device queue are
counted. The access to the device queue is unprotected against
concurrent access. With a lot of parallel I/O, especially with alias
devices enabled, the device queue can change while dasd_profile_start()
is accessing the queue. In the worst case this leads to a kernel panic
due to incorrect pointer accesses.
Fix this by taking the device lock before accessing the queue and
counting the requests. Additionally the check for a valid profile data
pointer can be done earlier to avoid unnecessary locking in a hot path.
In order for `AT_EMPTY_PATH` to work as expected, the fact
that the user wants that behavior needs to make it to `getname_flags`
or it will return ENOENT.
The crash occurred when call wake_up(&state->wait), and then we want
to look at the value in the state. However, bch_sectors_dirty_init()
is not found in the stack of any task. Since state is allocated on
the stack, we guess that bch_sectors_dirty_init() has exited, causing
bch_dirty_init_thread() to be unable to handle kernel paging request.
In order to verify this idea, we added some printing information during
wake_up(&state->wait). We find that "wake up" is printed twice, however
we only expect the last thread to wake up once.
```dmesg
[ 994.641004] alcache: bch_dirty_init_thread() wake up
[ 994.641018] alcache: bch_dirty_init_thread() wake up
[ 994.641523] alcache: bch_sectors_dirty_init() init exit
```
There is a race. If bch_sectors_dirty_init() exits after the first wake
up, the second wake up will trigger this bug("unable to handle kernel
paging request").
We believe it is very common to wake up twice if there is no dirty, but
crash is an extremely low probability event. It's hard for us to reproduce
this issue. We attached and detached continuously for a week, with a total
of more than one million attaches and only one crash.
Putting atomic_inc(&state.started) before kthread_run() can avoid waking
up twice.
Fixes: b144e45fc576 ("bcache: make bch_sectors_dirty_init() to be multithreaded") Signed-off-by: Mingzhe Zou <mingzhe.zou@easystack.cn> Cc: <stable@vger.kernel.org> Signed-off-by: Coly Li <colyli@suse.de> Link: https://lore.kernel.org/r/20231120052503.6122-8-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
md_end_clone_io() may overwrite error status in orig_bio->bi_status with
BLK_STS_OK. This could happen when orig_bio has BIO_CHAIN (split by
md_submit_bio => bio_split_to_limits, for example). As a result, upper
layer may miss error reported from md (or the device) and consider the
failed IO was successful.
Fix this by only update orig_bio->bi_status when current bio reports
error and orig_bio is BLK_STS_OK. This is the same behavior as
__bio_chain_endio().
Fixes: 10764815ff47 ("md: add io accounting for raid0 and raid5") Cc: stable@vger.kernel.org # v5.14+ Reported-by: Bhanu Victor DiCara <00bvd0+linux@gmail.com> Closes: https://lore.kernel.org/regressions/5727380.DvuYhMxLoT@bvd0/ Signed-off-by: Song Liu <song@kernel.org> Tested-by: Xiao Ni <xni@redhat.com> Reviewed-by: Yu Kuai <yukuai3@huawei.com> Acked-by: Guoqing Jiang <guoqing.jiang@linux.dev> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At line 35 the original r[nodes].b is not always allocatored from
__bch_btree_node_alloc(), and possibly initialized as NULL pointer by
caller of btree_gc_coalesce(). Therefore the change at line 36 is not
correct.
This patch replaces the mistaken IS_ERR() by IS_ERR_OR_NULL() to avoid
potential issue.
Fixes: 028ddcac477b ("bcache: Remove unnecessary NULL point check in node allocations") Cc: <stable@vger.kernel.org> # 6.5+ Cc: Zheng Wang <zyytlz.wz@163.com> Signed-off-by: Coly Li <colyli@suse.de> Link: https://lore.kernel.org/r/20231120052503.6122-9-colyli@suse.de Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a bug that when using the XEN hypervisor with bios with large
multi-page bio vectors on NVMe, the kernel deadlocks [1].
The deadlocks are caused by inability to map a large bio vector -
dma_map_sgtable always returns an error, this gets propagated to the block
layer as BLK_STS_RESOURCE and the block layer retries the request
indefinitely.
XEN uses the swiotlb framework to map discontiguous pages into contiguous
runs that are submitted to the PCIe device. The swiotlb framework has a
limitation on the length of a mapping - this needs to be announced with
the max_mapping_size method to make sure that the hardware drivers do not
create larger mappings.
Without max_mapping_size, the NVMe block driver would create large
mappings that overrun the maximum mapping size.
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Link: https://lore.kernel.org/stable/ZTNH0qtmint%2FzLJZ@mail-itl/ Tested-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com> Suggested-by: Christoph Hellwig <hch@lst.de> Cc: stable@vger.kernel.org Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Acked-by: Stefano Stabellini <sstabellini@kernel.org> Reviewed-by: Christoph Hellwig <hch@lst.de> Link: https://lore.kernel.org/r/151bef41-e817-aea9-675-a35fdac4ed@redhat.com Signed-off-by: Juergen Gross <jgross@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like various other ASUS ExpertBook-s, the ASUS ExpertBook B1402CVA
has an ACPI DSDT table that describes IRQ 1 as ActiveLow while
the kernel overrides it to EdgeHigh.
This prevents the keyboard from working. To fix this issue, add this laptop
to the skip_override_table so that the kernel does not override IRQ 1.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218114 Cc: All applicable <stable@vger.kernel.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code that checks for unknown boot options is unaware of the sysctl
alias facility, which maps bootparams to sysctl values. If a user sets
an old value that has a valid alias, a message about an invalid
parameter will be printed during boot, and the parameter will get passed
to init. Fix by checking for the existence of aliased parameters in the
unknown boot parameter code. If an alias exists, don't return an error
or pass the value to init.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com> Cc: stable@vger.kernel.org Fixes: 0a477e1ae21b ("kernel/sysctl: support handling command line aliases") Signed-off-by: Luis Chamberlain <mcgrof@kernel.org> Signed-off-by: Krister Johansen <kjlx@templeofstupid.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__insert_pending() allocate memory in atomic context, so the allocation
could fail, but we are not handling that failure now. It could lead
ext4_es_remove_extent() to get wrong reserved clusters, and the global
data blocks reservation count will be incorrect. The same to
extents_status entry preallocation, preallocate pending entry out of the
i_es_lock with __GFP_NOFAIL, make sure __insert_pending() and
__revise_pending() always succeeds.
Yikebaer reported an issue:
==================================================================
BUG: KASAN: slab-use-after-free in ext4_es_insert_extent+0xc68/0xcb0
fs/ext4/extents_status.c:894
Read of size 4 at addr ffff888112ecc1a4 by task syz-executor/8438
The flow of issue triggering is as follows:
1. remove es
raw es es removed es1
|-------------------| -> |----|.......|------|
2. insert es
es insert es1 merge with es es1 merge with es and free es1
|----|.......|------| -> |------------|------| -> |-------------------|
es merges with newes, then merges with es1, frees es1, then determines
if es1->es_len is 0 and triggers a UAF.
The code flow is as follows:
ext4_es_insert_extent
es1 = __es_alloc_extent(true);
es2 = __es_alloc_extent(true);
__es_remove_extent(inode, lblk, end, NULL, es1)
__es_insert_extent(inode, &newes, es1) ---> insert es1 to es tree
__es_insert_extent(inode, &newes, es2)
ext4_es_try_to_merge_right
ext4_es_free_extent(inode, es1) ---> es1 is freed
if (es1 && !es1->es_len)
// Trigger UAF by determining if es1 is used.
We determine whether es1 or es2 is used immediately after calling
__es_remove_extent() or __es_insert_extent() to avoid triggering a
UAF if es1 or es2 is freed.
Reported-by: Yikebaer Aizezi <yikebaer61@gmail.com> Closes: https://lore.kernel.org/lkml/CALcu4raD4h9coiyEBL4Bm0zjDwxC2CyPiTwsP3zFuhot6y9Beg@mail.gmail.com Fixes: 2a69c450083d ("ext4: using nofail preallocation in ext4_es_insert_extent()") Cc: stable@kernel.org Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230815070808.3377171-1-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to in ext4_es_insert_delayed_block(), we use preallocations that
do not fail to avoid inconsistencies, but we do not care about es that are
not must be kept, and we return 0 even if such es memory allocation fails.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-9-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Similar to in ext4_es_remove_extent(), we use a no-fail preallocation
to avoid inconsistencies, except that here we may have to preallocate
two extent_status.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-8-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
If __es_remove_extent() returns an error it means that when splitting
extent, allocating an extent that must be kept failed, where returning
an error directly would cause the extent tree to be inconsistent. So we
use GFP_NOFAIL to pre-allocate an extent_status and pass it to
__es_remove_extent() to avoid this problem.
In addition, since the allocated memory is outside the i_es_lock, the
extent_status tree may change and the pre-allocated extent_status is
no longer needed, so we release the pre-allocated extent_status when
es->es_len is not initialized.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-7-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
When splitting extent, if the second extent can not be dropped, we return
-ENOMEM and use GFP_NOFAIL to preallocate an extent_status outside of
i_es_lock and pass it to __es_remove_extent() to be used as the second
extent. This ensures that __es_remove_extent() is executed successfully,
thus ensuring consistency in the extent status tree. If the second extent
is not undroppable, we simply drop it and return 0. Then retry is no longer
necessary, remove it.
Now, __es_remove_extent() will always remove what it should, maybe more.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-6-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Pass a extent_status pointer prealloc to __es_insert_extent(). If the
pointer is non-null, it is used directly when a new extent_status is
needed to avoid memory allocation failures.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-5-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
Factor out __es_alloc_extent() and __es_free_extent(), which only allocate
and free extent_status in these two helpers.
The ext4_es_alloc_extent() function is split into __es_alloc_extent()
and ext4_es_init_extent(). In __es_alloc_extent() we allocate memory using
GFP_KERNEL | __GFP_NOFAIL | __GFP_ZERO if the memory allocation cannot
fail, otherwise we use GFP_ATOMIC. and the ext4_es_init_extent() is used to
initialize extent_status and update related variables after a successful
allocation.
This is to prepare for the use of pre-allocated extent_status later.
Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-4-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
In the extent status tree, we have extents which we can just drop without
issues and extents we must not drop - this depends on the extent's status
- currently ext4_es_is_delayed() extents must stay, others may be dropped.
A helper function is added to help determine if the current extent can
be dropped, although only ext4_es_is_delayed() extents cannot be dropped
currently.
Suggested-by: Jan Kara <jack@suse.cz> Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20230424033846.4732-3-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Stable-dep-of: 8e387c89e96b ("ext4: make sure allocate pending entry not fail") Signed-off-by: Sasha Levin <sashal@kernel.org>
In the current driver csid Test Pattern Generator (TPG) doesn't work.
This change:
- fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
- fixes the shift by one between test_pattern control value and the
actual pattern.
- drops fixed VC of 0x0a which testing showed prohibited some test
patterns in the CSID to produce output.
So that TPG starts working, but with the below limitations:
- only test_pattern=9 works as it should
- test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
- the rest of test_pattern's don't work (yavta doesn't get the data)
- regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
order is always the same (RGGB for any RAW8 or RAW10P format in
4608x2592 resolution).
CSID hardware on SM8250 can demux up to 4 simultaneous streams
based on virtual channel (vc) or datatype (dt).
The CSID subdevice entity now has 4 source ports that can be
enabled/disabled and thus can control which virtual channels
are enabled. Datatype demuxing not tested.
In order to keep a valid internal state of the subdevice,
implicit format propagation from the sink to the source pads
has been preserved. However, the format on each source pad
can be different and in that case it must be configured explicitly.
CSID's s_stream is called when any stream is started or stopped.
It will call configure_streams() that will rewrite IRQ settings to HW.
When multiple streams are running simultaneously there is an issue
when writing IRQ settings for one stream while another is still
running, thus avoid re-writing settings if they were not changed
in link setup, or by fully powering off the CSID hardware.
Signed-off-by: Milen Mitkov <quic_mmitkov@quicinc.com> Reviewed-by: Robert Foss <robert.foss@linaro.org> Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Acked-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stable-dep-of: e655d1ae9703 ("media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3") Signed-off-by: Sasha Levin <sashal@kernel.org>
Kernel test robot reported below warning ->
drivers/media/platform/qcom/camss/camss-csid-gen2.c:407:3:
warning: Value stored to 'val' is never read
[clang-analyzer-deadcode.DeadStores]
Replace hard coded value with val.
Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Souptick Joarder (HPE) <jrdr.linux@gmail.com> Reviewed-by: Robert Foss <robert.foss@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Stable-dep-of: e655d1ae9703 ("media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3") Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit 411740f5422a ("KVM: MIPS/MMU: Implement KVM_CAP_SYNC_MMU")
old_pte is no longer used in kvm_mips_map_page(). So remove it to fix a
build warning about variable set but not used:
arch/mips/kvm/mmu.c: In function 'kvm_mips_map_page':
>> arch/mips/kvm/mmu.c:701:29: warning: variable 'old_pte' set but not used [-Wunused-but-set-variable]
701 | pte_t *ptep, entry, old_pte;
| ^~~~~~~
Kent reported an occasional KASAN splat in lockdep. Mark then noted:
> I suspect the dodgy access is to chain_block_buckets[-1], which hits the last 4
> bytes of the redzone and gets (incorrectly/misleadingly) attributed to
> nr_large_chain_blocks.
That would mean @size == 0, at which point size_to_bucket() returns -1
and the above happens.
alloc_chain_hlocks() has 'size - req', for the first with the
precondition 'size >= rq', which allows the 0.
This code is trying to split a block, del_chain_block() takes what we
need, and add_chain_block() puts back the remainder, except in the
above case the remainder is 0 sized and things go sideways.
Fixes: 810507fe6fd5 ("locking/lockdep: Reuse freed chain_hlocks entries") Reported-by: Kent Overstreet <kent.overstreet@linux.dev> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Tested-by: Kent Overstreet <kent.overstreet@linux.dev> Link: https://lkml.kernel.org/r/20231121114126.GH8262@noisy.programming.kicks-ass.net Signed-off-by: Sasha Levin <sashal@kernel.org>
The driver needs to deregister and free the newly allocated dwc3 core
platform device on ACPI probe errors (e.g. probe deferral) and on driver
unbind but instead it leaked those resources while erroneously dropping
a reference to the parent platform device which is still in use.
For OF probing the driver takes a reference to the dwc3 core platform
device which has also always been leaked.
Fix the broken ACPI tear down and make sure to drop the dwc3 core
reference for both OF and ACPI.
Fixes: 8fd95da2cfb5 ("usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()") Fixes: 2bc02355f8ba ("usb: dwc3: qcom: Add support for booting with ACPI") Fixes: a4333c3a6ba9 ("usb: dwc3: Add Qualcomm DWC3 glue driver") Cc: stable@vger.kernel.org # 4.18 Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Cc: Lee Jones <lee@kernel.org> Signed-off-by: Johan Hovold <johan+linaro@kernel.org> Acked-by: Andrew Halaney <ahalaney@redhat.com> Link: https://lore.kernel.org/r/20231117173650.21161-2-johan+linaro@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 9cf87666fc6e ("USB: dwc3: qcom: fix ACPI platform device leak") Signed-off-by: Sasha Levin <sashal@kernel.org>
The host and subsystem NQNs are passed in the connect command payload and
interpreted as nul-terminated strings. Ensure they actually are
nul-terminated before using them.
Fixes: a07b4970f464 "nvmet: add a generic NVMe target") Reported-by: Alon Zahavi <zahavi.alon@gmail.com> Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
AFS doesn't really do locking on R/O volumes as fileservers don't maintain
state with each other and thus a lock on a R/O volume file on one
fileserver will not be be visible to someone looking at the same file on
another fileserver.
Further, the server may return an error if you try it.
Fix this by doing what other AFS clients do and handle filelocking on R/O
volume files entirely within the client and don't touch the server.
Fixes: 6c6c1d63c243 ("afs: Provide mount-time configurable byte-range file locking emulation") Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.
Address this by propagating correct information.
Fixes: 7c12aa08779c ("amd-xgbe: Move the PHY support into amd-xgbe") Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.
To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.
Fixes: c5aa9e3b8156 ("amd-xgbe: Initial AMD 10GbE platform driver") Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.
Fixes: e57f7a3feaef ("amd-xgbe: Prepare for working with more than one type of phy") Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is possible to add a ntuple rule which would like to direct packet to
a VF whose number of queues are greater/less than its PF's queue numbers.
For example a PF can have 2 Rx queues but a VF created on that PF can have
8 Rx queues. As of today, ntuple rule will reject rule because it is
checking the requested queue number against PF's number of Rx queues.
As a part of this fix if the action of a ntuple rule is to move a packet
to a VF's queue then the check is removed. Also, a debug information is
printed to aware user that it is user's responsibility to cross check if
the requested queue number on that VF is a valid one.
Fixes: f0a1913f8a6f ("octeontx2-pf: Add support for ethtool ntuple filters") Signed-off-by: Suman Ghosh <sumang@marvell.com> Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20231121165624.3664182-1-sumang@marvell.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
It is quite obvious that this is a SMC DECLINE message, which means that
the applications received SMC protocol message.
We found that this was caused by the following situations:
As a result, a decline message was sent in the implementation, and this
message was read from TCP by the already-fallback connection.
This patch double the client timeout as 2x of the server value,
With this simple change, the Decline messages should never cross or
collide (during Confirm link timeout).
This issue requires an immediate solution, since the protocol updates
involve a more long-term solution.
Fixes: 0fb0b02bd6fd ("net/smc: adapt SMC client code to use the LLC flow") Signed-off-by: D. Wythe <alibuda@linux.alibaba.com> Reviewed-by: Wen Gu <guwen@linux.alibaba.com> Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
- power on
- check logs
- shutdown
- after detecting the system shutdown, disconnect power
- after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.
In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.
It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver") Reported-by: Herb Wei <weihao.bj@ieisystem.com> Tested-by: Herb Wei <weihao.bj@ieisystem.com> Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com> Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
hid_debug_events_release releases resources bound to the HID device instance.
hid_device_release releases the underlying HID device instance potentially
before hid_debug_events_release has completed releasing debug resources bound
to the same HID device instance.
Reference count to prevent the HID device instance from being torn down
preemptively when HID debugging support is used. When count reaches zero,
release core resources of HID device instance using hiddev_free.
This unique identifier is currently used only for ensuring uniqueness in
sysfs. However, this could be handful for userspace to refer to a specific
hid_device by this id.
2 use cases are in my mind: LEDs (and their naming convention), and
HID-BPF.
During 'ifconfig <netdev> down' one RSS memory was not getting freed.
This patch fixes the same.
Fixes: 81a4362016e7 ("octeontx2-pf: Add RSS multi group support") Signed-off-by: Suman Ghosh <sumang@marvell.com> Reviewed-by: Simon Horman <horms@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
wg_xmit() can be called concurrently, KCSAN reported [1]
some device stats updates can be lost.
Use DEV_STATS_INC() for this unlikely case.
[1]
BUG: KCSAN: data-race in wg_xmit / wg_xmit
read-write to 0xffff888104239160 of 8 bytes by task 1375 on cpu 0:
wg_xmit+0x60f/0x680 drivers/net/wireguard/device.c:231
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3543 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3559
...
read-write to 0xffff888104239160 of 8 bytes by task 1378 on cpu 1:
wg_xmit+0x60f/0x680 drivers/net/wireguard/device.c:231
__netdev_start_xmit include/linux/netdevice.h:4918 [inline]
netdev_start_xmit include/linux/netdevice.h:4932 [inline]
xmit_one net/core/dev.c:3543 [inline]
dev_hard_start_xmit+0x11b/0x3f0 net/core/dev.c:3559
...
v2: also change wg_packet_consume_data_done() (Hangbin Liu)
and wg_packet_purge_staged_packets()
Fixes: e7096c131e51 ("net: WireGuard secure network tunnel") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The Innolux G101ICE-L01 datasheet [1] page 17 table
6.1 INPUT SIGNAL TIMING SPECIFICATIONS
indicates that maximum vertical blanking time is 40 lines.
Currently the driver uses 29 lines.
Fix it, and since this panel is a DE panel, adjust the timings
to make them less hostile to controllers which cannot do 1 px
HSA/VSA, distribute the delays evenly between all three parts.
For "boe,tv105wum-nw0" this special panel, it is stipulated in
the panel spec that MIPI needs to keep the LP11 state before
the lcm_reset pin is pulled high.
Signed-off-by: Shuijing Li <shuijing.li@mediatek.com> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20230515094955.15982-3-shuijing.li@mediatek.com
Stable-dep-of: 6965809e5269 ("drm/panel: auo,b101uan08.3: Fine tune the panel power sequence") Signed-off-by: Sasha Levin <sashal@kernel.org>
When kafs tries to look up a cell in the DNS or the local config, it will
translate a lookup failure into EDESTADDRREQ whereas OpenAFS translates it
into ENOENT. Applications such as West expect the latter behaviour and
fail if they see the former.
This can be seen by trying to mount an unknown cell:
# mount -t afs %example.com:cell.root /mnt
mount: /mnt: mount(2) system call failed: Destination address required.
Fixes: 4d673da14533 ("afs: Support the AFS dynamic root") Reported-by: Markus Suvanto <markus.suvanto@gmail.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216637 Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org Signed-off-by: Sasha Levin <sashal@kernel.org>
This commit fixes a bug in commit 9ed9895370ae ("driver core: Functional
dependencies tracking support") where the device link status was
incorrectly updated in the driver unbind path before all the device's
resources were released.
Fixes: 9ed9895370ae ("driver core: Functional dependencies tracking support") Cc: stable <stable@kernel.org> Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Closes: https://lore.kernel.org/all/20231014161721.f4iqyroddkcyoefo@pengutronix.de/ Signed-off-by: Saravana Kannan <saravanak@google.com> Cc: Thierry Reding <thierry.reding@gmail.com> Cc: Yang Yingliang <yangyingliang@huawei.com> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Cc: Mark Brown <broonie@kernel.org> Cc: Matti Vaittinen <mazziesaccount@gmail.com> Cc: James Clark <james.clark@arm.com> Acked-by: "Rafael J. Wysocki" <rafael@kernel.org> Tested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20231018013851.3303928-1-saravanak@google.com Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1. Change directory to the tracefs directory
2. Create a kprobe event (doesn't matter what one)
3. Open bash file descriptor 5 on the enable file of the kprobe event
4. Delete the kprobe event (removes the files too)
5. Close the bash file descriptor 5
What happens here is that the kprobe event creates a trace_event_file
"file" descriptor that represents the file in tracefs to the event. It
maintains state of the event (is it enabled for the given instance?).
Opening the "enable" file gets a reference to the event "file" descriptor
via the open file descriptor. When the kprobe event is deleted, the file is
also deleted from the tracefs system which also frees the event "file"
descriptor.
But as the tracefs file is still opened by user space, it will not be
totally removed until the final dput() is called on it. But this is not
true with the event "file" descriptor that is already freed. If the user
does a write to or simply closes the file descriptor it will reference the
event "file" descriptor that was just freed, causing a use-after-free bug.
To solve this, add a ref count to the event "file" descriptor as well as a
new flag called "FREED". The "file" will not be freed until the last
reference is released. But the FREE flag will be set when the event is
removed to prevent any more modifications to that event from happening,
even if there's still a reference to the event "file" descriptor.
As reported by Mahesh & Aneesh, opal_prd_msg_notifier() triggers a
FORTIFY_SOURCE warning:
memcpy: detected field-spanning write (size 32) of single field "&item->msg" at arch/powerpc/platforms/powernv/opal-prd.c:355 (size 4)
WARNING: CPU: 9 PID: 660 at arch/powerpc/platforms/powernv/opal-prd.c:355 opal_prd_msg_notifier+0x174/0x188 [opal_prd]
NIP opal_prd_msg_notifier+0x174/0x188 [opal_prd]
LR opal_prd_msg_notifier+0x170/0x188 [opal_prd]
Call Trace:
opal_prd_msg_notifier+0x170/0x188 [opal_prd] (unreliable)
notifier_call_chain+0xc0/0x1b0
atomic_notifier_call_chain+0x2c/0x40
opal_message_notify+0xf4/0x2c0
This happens because the copy is targeting item->msg, which is only 4
bytes in size, even though the enclosing item was allocated with extra
space following the msg.
To fix the warning define struct opal_prd_msg with a union of the header
and a flex array, and have the memcpy target the flex array.
We could race with SQ thread exit, and if we do, we'll hit a NULL pointer
dereference when the thread is cleared. Grab the SQPOLL data lock before
attempting to get the task cpu and pid for fdinfo, this ensures we have a
stable view of it.
[WHY]
Flush command sent to DMCUB spends more time for execution on
a dGPU than on an APU. This causes cursor lag when using high
refresh rate mouses.
[HOW]
1. Change the DMCUB mailbox memory location from FB to inbox.
2. Only change windows memory to inbox.
Cc: Mario Limonciello <mario.limonciello@amd.com> Cc: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Acked-by: Alex Hung <alex.hung@amd.com> Signed-off-by: Lewis Huang <lewis.huang@amd.com> Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We should not leak the pointer where we couldn't grab the reference
on to the caller because it can be that the error handling still
tries to put the reference then.
Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ATRM ACPI method is for fetching the dGPU vbios rom
image on laptops and all-in-one systems. It should not be
used for external add in cards. If the dGPU is thunderbolt
connected, don't try ATRM.
v2: pci_is_thunderbolt_attached only works for Intel. Use
pdev->external_facing instead.
v3: dev_is_removable() seems to be what we want
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2925 Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The incoming strings might not be terminated by a newline
or a 0.
(found while testing a program that just wrote the string
itself, causing a crash)
Cc: stable@vger.kernel.org Fixes: e3933f26b657 ("drm/amd/pp: Add edit/commit/show OD clock/voltage support in sysfs") Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wrong check of gdb backup in meta bg as following:
first_group is the first group of meta_bg which contains target group, so
target group is always >= first_group. We check if target group has gdb
backup by comparing first_group with [group + 1] and [group +
EXT4_DESC_PER_BLOCK(sb) - 1]. As group >= first_group, then [group + N] is
> first_group. So no copy of gdb backup in meta bg is done in
setup_new_flex_group_blocks.
No need to do gdb backup copy in meta bg from setup_new_flex_group_blocks
as we always copy updated gdb block to backups at end of
ext4_flex_group_add as following:
ext4_flex_group_add
/* no gdb backup copy for meta bg any more */
setup_new_flex_group_blocks
/* update current group number */
ext4_update_super
sbi->s_groups_count += flex_gd->count;
/*
* if group in meta bg contains backup is added, the primary gdb block
* of the meta bg will be copy to backup in new added group here.
*/
for (; gdb_num <= gdb_num_end; gdb_num++)
update_backups(...)
In summary, we can remove wrong gdb backup copy code in
setup_new_flex_group_blocks.
When big allocate feature is enabled, we need to count and update
reserved clusters before removing a delayed only extent_status entry.
{init|count|get}_rsvd() have already done this, but the start block
number of this counting isn't correct in the following case.
lblk end
| |
v v
-------------------------
| | orig_es
-------------------------
^ ^
len1 is 0 | len2 |
If the start block of the orig_es entry founded is bigger than lblk, we
passed lblk as start block to count_rsvd(), but the length is correct,
finally, the range to be counted is offset. This patch fix this by
passing the start blocks to 'orig_es->lblk + len1'.
Commit 0aeaa2559d6d5 ("ext4: fix corruption when online resizing a 1K
bigalloc fs") found that primary superblock's offset in its group is
not equal to offset of backup superblock in its group when block size
is 1K and bigalloc is enabled. As group descriptor blocks are right
after superblock, we can't pass block number of gdb to update_backups
for the same reason.
The root casue of the issue above is that leading 1K padding block is
count as data block offset for primary block while backup block has no
padding block offset in its group.
Remove padding data block count to fix the issue for gdb backups.
For meta_bg case, update_backups treat blk_off as block number, do no
conversion in this case.
The function ext4_init_acl() calls posix_acl_create() which is
responsible for applying the umask. But without
CONFIG_EXT4_FS_POSIX_ACL, ext4_init_acl() is an empty inline function,
and nobody applies the umask.
This fixes a bug which causes the umask to be ignored with O_TMPFILE
on ext4:
I couldn't reproduce the reported issue. What I did, based on a pcap
packet log provided by the reporter:
- Used same chip version (RTL8168h)
- Set MAC address to the one used on the reporters system
- Replayed the EAPOL unicast packet that, according to the reporter,
was filtered out by the mc filter.
The packet was properly received.
Therefore the root cause of the reported issue seems to be somewhere
else. Disabling mc filtering completely for the most common chip
version is a quite big hammer. Therefore revert the change and wait
for further analysis results from the reporter.
Cc: stable@vger.kernel.org Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
check_clock doesn't account for vfe_lite which means that vfe_lite will
never get validated by this routine. Add the clock name to the expected set
to remediate.
Fixes: 7319cdf189bb ("media: camss: Add support for VFE hardware version Titan 170") Cc: stable@vger.kernel.org Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two problems with the current vfe_disable_output() routine.
Firstly we rightly use a spinlock to protect output->gen2.active_num
everywhere except for in the IDLE timeout path of vfe_disable_output().
Even if that is not racy "in practice" somehow it is by happenstance not
by design.
Secondly we do not get consistent behaviour from this routine. On
sc8280xp 50% of the time I get "VFE idle timeout - resetting". In this
case the subsequent capture will succeed. The other 50% of the time, we
don't hit the idle timeout, never do the VFE reset and subsequent
captures stall indefinitely.
Rewrite the vfe_disable_output() routine to
- Quiesce write masters with vfe_wm_stop()
- Set active_num = 0
remembering to hold the spinlock when we do so followed by
- Reset the VFE
Testing on sc8280xp and sdm845 shows this to be a valid fix.
Fixes: 7319cdf189bb ("media: camss: Add support for VFE hardware version Titan 170") Cc: stable@vger.kernel.org Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Right now it is possible to do a vfe_get() with the internal reference
count at 1. If vfe_check_clock_rates() returns non-zero then we will
leave the reference count as-is and
vfe_get() should not attempt to roll-back on error when the ref-count is
non-zero as the upper layers will still do their own vfe_put() operations.
vfe_put() will drop the reference count and do the necessary power
domain release, the cleanup jumps in vfe_get() should only be run when
the ref-count is zero.
We need to make sure camss_configure_pd() happens before
camss_register_entities() as the vfe_get() path relies on the pointer
provided by camss_configure_pd().
Fix the ordering sequence in probe to ensure the pointers vfe_get() demands
are present by the time camss_register_entities() runs.
In order to facilitate backporting to stable kernels I've moved the
configure_pd() call pretty early on the probe() function so that
irrespective of the existence of the old error handling jump labels this
patch should still apply to -next circa Aug 2023 to v5.13 inclusive.
Due to a flaw in the hardware design, the GL9750 replay timer frequently
times out when ASPM is enabled. As a result, the warning messages will
often appear in the system log when the system accesses the GL9750
PCI config. Therefore, the replay timer timeout must be masked.
Fixes: d7133797e9e1 ("mmc: sdhci-pci-gli: A workaround to allow GL9750 to enter ASPM L1.2") Signed-off-by: Victor Shih <victor.shih@genesyslogic.com.tw> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Kai-Heng Feng <kai.heng.geng@canonical.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20231107095741.8832-2-victorshihgli@gmail.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device that support DASH may be reseted or powered off during suspend.
So driver needs to handle DASH during system suspend and resume. Or
DASH firmware will influence device behavior and causes network lost.
Objcg vectors attached to slab pages to store slab object ownership
information are allocated using gfp flags for the original slab
allocation. Depending on slab page order and the size of slab objects,
objcg vector can take several pages.
If the original allocation was done with the __GFP_NOFAIL flag, it
triggered a warning in the page allocation code. Indeed, order > 1 pages
should not been allocated with the __GFP_NOFAIL flag.
Fix this by simply dropping the __GFP_NOFAIL flag when allocating the
objcg vector. It effectively allows to skip the accounting of a single
slab object under a heavy memory pressure.
An alternative would be to implement the mechanism to fallback to order-0
allocations for accounting metadata, which is also not perfect because it
will increase performance penalty and memory footprint of the kernel
memory accounting under memory pressure.
Link: https://lkml.kernel.org/r/ZUp8ZFGxwmCx4ZFr@P9FQF9L96D.corp.robot.car Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev> Reported-by: Christoph Lameter <cl@linux.com> Closes: https://lkml.kernel.org/r/6b42243e-f197-600a-5d22-56bd728a5ad8@gentwo.org Acked-by: Shakeel Butt <shakeelb@google.com> Cc: Matthew Wilcox <willy@infradead.org> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When GL9750 enters ASPM L1 sub-states, it will stay at L1.1 and will not
enter L1.2. The workaround is to toggle PM state to allow GL9750 to enter
ASPM L1.2.
Initialise the try sink compose rectangle size to the sink compose
rectangle for binner and scaler sub-devices. This was missed due to the
faulty condition that lead to the compose rectangles to be initialised for
the pixel array sub-device where it is not relevant.
The hfi parser, parses the capabilities received from venus firmware and
copies them to core capabilities. Consider below api, for example,
fill_caps - In this api, caps in core structure gets updated with the
number of capabilities received in firmware data payload. If the same api
is called multiple times, there is a possibility of copying beyond the max
allocated size in core caps.
Similar possibilities in fill_raw_fmts and fill_profile_level functions.
Buffer requirement, for different buffer type, comes from video firmware.
While copying these requirements, there is an OOB possibility when the
payload from firmware is more than expected size. Fix the check to avoid
the OOB possibility.
projects / linux-stable / log