The original set [1][2] was expected to undo a suboptimal fix in [2], and
replace it with a better fix [1]. However, as reported by Dan Moulding [2]
causes an issue with raid5 with journal device.
Revert [2] for now to close the issue. We will follow up on another issue
reported by Juxiao Bi, as [2] is expected to fix it. We believe this is a
good trade-off, because the latter issue happens less freqently.
In the meanwhile, we will NOT revert [1], as it contains the right logic.
[1] commit d6e035aad6c0 ("md: bypass block throttle for superblock update")
[2] commit bed9e27baf52 ("Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"")
Reported-by: Dan Moulding <dan@danm.net> Closes: https://lore.kernel.org/linux-raid/20240123005700.9302-1-dan@danm.net/ Fixes: bed9e27baf52 ("Revert "md/raid5: Wait for MD_SB_CHANGE_PENDING in raid5d"") Cc: stable@vger.kernel.org # v5.19+ Cc: Junxiao Bi <junxiao.bi@oracle.com> Cc: Yu Kuai <yukuai3@huawei.com> Signed-off-by: Song Liu <song@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtc on the mox shares its interrupt line with the moxtet bus. Set
the interrupt type to be consistent between both devices. This ensures
correct setup of the interrupt line regardless of probing order.
The special casing was originally added in pre-git history; reproducing
the commit log here:
> commit a318a92567d77
> Author: Andrew Morton <akpm@osdl.org>
> Date: Sun Sep 21 01:42:22 2003 -0700
>
> [PATCH] Speed up direct-io hugetlbpage handling
>
> This patch short-circuits all the direct-io page dirtying logic for
> higher-order pages. Without this, we pointlessly bounce BIOs up to
> keventd all the time.
In the last twenty years, compound pages have become used for more than
just hugetlb. Rewrite these functions to operate on folios instead
of pages and remove the special case for hugetlbfs; I don't think
it's needed any more (and if it is, we can put it back in as a call
to folio_test_hugetlb()).
This was found by inspection; as far as I can tell, this bug can lead
to pages used as the destination of a direct I/O read not being marked
as dirty. If those pages are then reclaimed by the MM without being
dirtied for some other reason, they won't be written out. Then when
they're faulted back in, they will not contain the data they should.
It'll take a pretty unusual setup to produce this problem with several
races all going the wrong way.
This problem predates the folio work; it could for example have been
triggered by mmaping a THP in tmpfs and using that as the target of an
O_DIRECT read.
To properly handle ACK on the bus when transferring more than one
message in polling mode, move the polling handling loop from
s3c24xx_i2c_message_start() to s3c24xx_i2c_doxfer(). This way
i2c_s3c_irq_nextbyte() is always executed till the end, properly
acknowledging the IRQ bits and no recursive calls to
i2c_s3c_irq_nextbyte() are made.
While touching this, also fix finishing transfers in polling mode by
using common code path and always waiting for the bus to become idle
and disabled.
To properly handle read transfers in polling mode, no waiting for the ACK
state is needed as it will never come. Just wait a bit to ensure start
state is on the bus and continue processing next bytes.
Fixes: 117053f77a5a ("i2c: s3c2410: Add polling mode support") Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Chanho Park <chanho61.park@samsung.com> Reviewed-by: Andi Shyti <andi.shyti@kernel.org> Signed-off-by: Wolfram Sang <wsa@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
idev->mc_ifc_count can be written over without proper locking.
Originally found by syzbot [1], fix this issue by encapsulating calls
to mld_ifc_stop_work() (and mld_gq_stop_work() for good measure) with
mutex_lock() and mutex_unlock() accordingly as these functions
should only be called with mc_lock per their declarations.
[1]
BUG: KCSAN: data-race in ipv6_mc_down / mld_ifc_work
write to 0xffff88813a80c832 of 1 bytes by task 22 on cpu 1:
mld_ifc_work+0x54c/0x7b0 net/ipv6/mcast.c:2653
process_one_work kernel/workqueue.c:2627 [inline]
process_scheduled_works+0x5b8/0xa30 kernel/workqueue.c:2700
worker_thread+0x525/0x730 kernel/workqueue.c:2781
...
Fixes: 2d9a93b4902b ("mld: convert from timer to delayed work") Reported-by: syzbot+a9400cabb1d784e49abf@syzkaller.appspotmail.com Link: https://lore.kernel.org/all/000000000000994e09060ebcdffb@google.com/ Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru> Acked-by: Taehee Yoo <ap420073@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Hangbin Liu <liuhangbin@gmail.com> Link: https://lore.kernel.org/r/20240117172102.12001-1-n.zhandarovich@fintech.ru Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
'qos_pfc' test checks PFC behavior. The idea is to limit the traffic
using a shaper somewhere in the flow of the packets. In this area, the
buffer is smaller than the buffer at the beginning of the flow, so it fills
up until there is no more space left. The test configures there PFC
which is supposed to notice that the headroom is filling up and send PFC
Xoff to indicate the transmitter to stop sending traffic for the priorities
sharing this PG.
The Xon/Xoff threshold is auto-configured and always equal to
2*(MTU rounded up to cell size). Even after sending the PFC Xoff packet,
traffic will keep arriving until the transmitter receives and processes
the PFC packet. This amount of traffic is known as the PFC delay allowance.
Currently the buffer for the delay traffic is configured as 100KB. The
MTU in the test is 10KB, therefore the threshold for Xoff is about 20KB.
This allows 80KB extra to be stored in this buffer.
8-lane ports use two buffers among which the configured buffer is split,
the Xoff threshold then applies to each buffer in parallel.
The test does not take into account the behavior of 8-lane ports, when the
ports are configured to 400Gbps with 8 lanes or 800Gbps with 8 lanes,
packets are dropped and the test fails.
Check if the relevant ports use 8 lanes, in such case double the size of
the buffer, as the headroom is split half-half.
Cc: Shuah Khan <shuah@kernel.org> Fixes: bfa804784e32 ("selftests: mlxsw: Add a PFC test") Signed-off-by: Amit Cohen <amcohen@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: Petr Machata <petrm@nvidia.com> Acked-by: Paolo Abeni <pabeni@redhat.com> Link: https://lore.kernel.org/r/23ff11b7dff031eb04a41c0f5254a2b636cd8ebb.1705502064.git.petrm@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.
One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.
In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.
Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.
Add a test case to make sure the machine does not crash when this
condition is hit.
Lately, a bug was found when many TC filters are added - at some point,
several bugs are printed to dmesg [1] and the switch is crashed with
segmentation fault.
The issue starts when gen_pool_free() fails because of unexpected
behavior - a try to free memory which is already freed, this leads to BUG()
call which crashes the switch and makes many other bugs.
Trying to track down the unexpected behavior led to a bug in eRP code. The
function mlxsw_sp_acl_erp_table_alloc() gets a pointer to the allocated
index, sets the value and returns an error code. When gen_pool_alloc()
fails it returns address 0, we track it and return -ENOBUFS outside, BUT
the call for gen_pool_alloc() already override the index in erp_table
structure. This is a problem when such allocation is done as part of
table expansion. This is not a new table, which will not be used in case
of allocation failure. We try to expand eRP table and override the
current index (non-zero) with zero. Then, it leads to an unexpected
behavior when address 0 is freed twice. Note that address 0 is valid in
erp_table->base_index and indeed other tables use it.
gen_pool_alloc() fails in case that there is no space left in the
pre-allocated pool, in our case, the pool is limited to
ACL_MAX_ERPT_BANK_SIZE, which is read from hardware. When more than max
erp entries are required, we exceed the limit and return an error, this
error leads to "Failed to migrate vregion" print.
Fix this by changing erp_table->base_index only in case of a successful
allocation.
Add a test case for such a scenario. Without this fix it causes
segmentation fault:
$ TESTS="max_erp_entries_test" ./tc_flower.sh
./tc_flower.sh: line 988: 1560 Segmentation fault tc filter del dev $h2 ingress chain $i protocol ip pref $i handle $j flower &>/dev/null
Accessing an ethernet device that is powered off or clock gated might
cause the CPU to hang. Add ethnl_ops_begin/complete in
ethnl_set_features() to protect against this.
Fixes: 0980bfcd6954 ("ethtool: set netdev features with FEATURES_SET request") Signed-off-by: Ludvig Pärsson <ludvig.parsson@axis.com> Link: https://lore.kernel.org/r/20240117-etht2-v2-1-1a96b6e8c650@axis.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 5d5314d6795f ("kdb: core for kgdb back end (1 of 2)") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Inside decrement_ttl() upon discovering that the packet ttl has exceeded,
__IP_INC_STATS and __IP6_INC_STATS macros can be called from preemptible
context having the following backtrace:
It is still possible to set on the NFT_SET_CONCAT flag by specifying a
set size and no field description, report EINVAL in such case.
Fixes: 1b6345d4160e ("netfilter: nf_tables: check NFT_SET_CONCAT flag if field_count is specified") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Delete from packet path relies on the garbage collector to purge
elements with NFT_SET_ELEM_DEAD_BIT on.
Skip these dead elements from nf_tables_dump_setelem() path, I very
rarely see tests/shell/testcases/maps/typeof_maps_add_delete reports
[DUMP FAILED] showing a mismatch in the expected output with an element
that should not be there.
If the netlink dump happens before GC worker run, it might show dead
elements in the ruleset listing.
nft_rhash_get() already skips dead elements in nft_rhash_cmp(),
therefore, it already does not show the element when getting a single
element via netlink control plane.
Fixes: 5f68718b34a5 ("netfilter: nf_tables: GC transaction API to avoid race with control plane") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The set description provides the size of each field in the set whose sum
should not mismatch the set key length, bail out otherwise.
I did not manage to crash nft_set_pipapo with mismatch fields and set key
length so far, but this is UB which must be disallowed.
Fixes: f3a2181e16f1 ("netfilter: nf_tables: Support for sets with multiple ranged fields") Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For PTR_TO_FLOW_KEYS, check_flow_keys_access() only uses fixed off
for validation. However, variable offset ptr alu is not prohibited
for this ptr kind. So the variable offset is not checked.
Fix this by rejecting ptr alu with variable offset on flow_keys.
Applying the patch rejects the program with "R7 pointer arithmetic
on flow_keys prohibited".
Fixes: d58e468b1112 ("flow_dissector: implements flow dissector BPF hook") Signed-off-by: Hao Sun <sunhao.th@gmail.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Yonghong Song <yonghong.song@linux.dev> Link: https://lore.kernel.org/bpf/20240115082028.9992-1-sunhao.th@gmail.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Multiple disable_irq_wake() calls will keep decreasing the IRQ
wake_depth, When wake_depth is 0, calling disable_irq_wake() again,
will report the above calltrace.
Due to the need to appear in pairs, we cannot call disable_irq_wake()
without calling enable_irq_wake(). Fix this by making sure there are
no unbalanced disable_irq_wake() calls.
Fixes: 3172d3afa998 ("stmmac: support wake up irq from external sources (v3)") Signed-off-by: Qiang Ma <maqianga@uniontech.com> Reviewed-by: Simon Horman <horms@kernel.org> Link: https://lore.kernel.org/r/20240112021249.24598-1-maqianga@uniontech.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
In ravb_start_xmit(), ravb driver uses u32 variable to store result of
dma_map_single() call. Since ravb hardware has 32-bit address fields in
descriptors, this works properly when mapping is successful - it is
platform's job to provide mapping addresses that fit into hardware
limitations.
However, in failure case dma_map_single() returns DMA_MAPPING_ERROR
constant that is 64-bit when dma_addr_t is 64-bit. Storing this constant
in u32 leads to truncation, and further call to dma_mapping_error()
fails to notice the error.
Fix that by storing result of dma_map_single() in a dma_addr_t
variable.
subflow_finish_connect() uses four fields (backup, join_id, thmac, none)
that may contain garbage unless OPTION_MPTCP_MPJ_SYNACK has been set
in mptcp_parse_option()
Fixes: f296234c98a8 ("mptcp: Add handling of incoming MP_JOIN requests") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Florian Westphal <fw@strlen.de> Cc: Peter Krystad <peter.krystad@linux.intel.com> Cc: Matthieu Baerts <matttbe@kernel.org> Cc: Mat Martineau <martineau@kernel.org> Cc: Geliang Tang <geliang.tang@linux.dev> Reviewed-by: Simon Horman <horms@kernel.org> Acked-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Link: https://lore.kernel.org/r/20240111194917.4044654-4-edumazet@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The parameter 'sk' became useless since the code using it was dropped
from mptcp_get_options() in the commit 8d548ea1dd15 ("mptcp: do not set
unconditionally csum_reqd on incoming opt"). Let's drop it.
Signed-off-by: Geliang Tang <geliang.tang@suse.com> Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: c1665273bdc7 ("mptcp: strict validation before using mp_opt->hmac") Signed-off-by: Sasha Levin <sashal@kernel.org>
The RZ/G3S SMARC Module has 2 KSZ9131 PHYs. In this setup, the KSZ9131 PHY
is used with the ravb Ethernet driver. It has been discovered that when
bringing the Ethernet interface down/up continuously, e.g., with the
following sh script:
$ while :; do ifconfig eth0 down; ifconfig eth0 up; done
the link speed and duplex are wrong after interrupting the bring down/up
operation even though the Ethernet interface is up. To recover from this
state the following configuration sequence is necessary (executed
manually):
$ ifconfig eth0 down
$ ifconfig eth0 up
The behavior has been identified also on the Microchip SAMA7G5-EK board
which runs the macb driver and uses the same PHY.
The order of PHY-related operations in ravb_open() is as follows:
ravb_open() ->
ravb_phy_start() ->
ravb_phy_init() ->
of_phy_connect() ->
phy_connect_direct() ->
phy_attach_direct() ->
phy_init_hw() ->
phydev->drv->soft_reset()
phydev->drv->config_init()
phydev->drv->config_intr()
phy_resume()
kszphy_resume()
The order of PHY-related operations in ravb_close is as follows:
ravb_close() ->
phy_stop() ->
phy_suspend() ->
kszphy_suspend() ->
genphy_suspend()
// set BMCR_PDOWN bit in MII_BMCR
In genphy_suspend() setting the BMCR_PDWN bit in MII_BMCR switches the PHY
to Software Power-Down (SPD) mode (according to the KSZ9131 datasheet).
Thus, when opening the interface after it has been previously closed (via
ravb_close()), the phydev->drv->config_init() and
phydev->drv->config_intr() reach the KSZ9131 PHY driver via the
ksz9131_config_init() and kszphy_config_intr() functions.
KSZ9131 specifies that the MII management interface remains operational
during SPD (Software Power-Down), but (according to manual):
- Only access to the standard registers (0 through 31) is supported.
- Access to MMD address spaces other than MMD address space 1 is possible
if the spd_clock_gate_override bit is set.
- Access to MMD address space 1 is not possible.
The spd_clock_gate_override bit is not used in the KSZ9131 driver.
ksz9131_config_init() configures RGMII delay, pad skews and LEDs by
accessesing MMD registers other than those in address space 1.
The datasheet for the KSZ9131 does not specify what happens if registers
from an unsupported address space are accessed while the PHY is in SPD.
To fix the issue the .soft_reset method has been instantiated for KSZ9131,
too. This resets the PHY to the default state before doing any
configurations to it, thus switching it out of SPD.
Fixes: bff5b4b37372 ("net: phy: micrel: add Microchip KSZ9131 initial driver") Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The value of AM65_CPSW_MAX_PACKET_SIZE represents the maximum length
of a received frame. This value is written to the register
AM65_CPSW_PORT_REG_RX_MAXLEN.
The maximum MTU configured on the network device should then leave
some room for the ethernet headers and frame check. Otherwise, if
the network interface is configured to its maximum mtu possible,
the frames will be larger than AM65_CPSW_MAX_PACKET_SIZE and will
get dropped as oversized.
The switch supports ethernet frame sizes between 64 and 2024 bytes
(including VLAN) as stated in the technical reference manual, so
define AM65_CPSW_MAX_PACKET_SIZE with that maximum size.
The variable rmnet_link_ops assign a *bigger* maxtype which leads to a
global out-of-bounds read when parsing the netlink attributes. See bug
trace below:
==================================================================
BUG: KASAN: global-out-of-bounds in validate_nla lib/nlattr.c:386 [inline]
BUG: KASAN: global-out-of-bounds in __nla_validate_parse+0x24af/0x2750 lib/nlattr.c:600
Read of size 1 at addr ffffffff92c438d0 by task syz-executor.6/84207
The zpci_get_max_write_size() helper is used to determine the maximum
size a PCI store or load can use at a given __iomem address.
For the PCI block store the following restrictions apply:
1. The dst + len must not cross a 4K boundary in the (pseudo-)MMIO space
2. len must not exceed ZPCI_MAX_WRITE_SIZE
3. len must be a multiple of 8 bytes
4. The src address must be double word (8 byte) aligned
5. The dst address must be double word (8 byte) aligned
Otherwise only a normal PCI store which takes its src value from
a register can be used. For these PCI store restriction 1 still applies.
Similarly 1 also applies to PCI loads.
It turns out zpci_max_write_size() instead implements stricter
conditions which prevents PCI block stores from being used where they
can and should be used. In particular instead of conditions 4 and 5 it
wrongly enforces both dst and src to be size aligned. This indirectly
covers condition 1 but also prevents many legal PCI block stores.
On top of the functional shortcomings the zpci_get_max_write_size() is
misnamed as it is used for both read and write size calculations. Rename
it to zpci_get_max_io_size() and implement the listed conditions
explicitly.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com> Fixes: cd24834130ac ("s390/pci: base support") Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
[agordeev@linux.ibm.com replaced spaces with tabs] Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The PCI driver invokes the PHY APIs using the ks_pcie_enable_phy()
function. The PHY in this case is the Serdes. It is possible that the
PCI instance is configured for two lane operation across two different
Serdes instances, using one lane of each Serdes.
In such a configuration, if the reference clock for one Serdes is
provided by the other Serdes, it results in a race condition. After the
Serdes providing the reference clock is initialized by the PCI driver by
invoking its PHY APIs, it is not guaranteed that this Serdes remains
powered on long enough for the PHY APIs based initialization of the
dependent Serdes. In such cases, the PLL of the dependent Serdes fails
to lock due to the absence of the reference clock from the former Serdes
which has been powered off by the PM Core.
Fix this by obtaining reference to the PHYs before invoking the PHY
initialization APIs and releasing reference after the initialization is
complete.
The nvmet_tcp_handle_h2c_data_pdu() function should take into
consideration the possibility that the header digest and/or the data
digests are enabled when calculating the expected PDU length, before
comparing it to the value stored in cmd->pdu_len.
Fixes: efa56305908b ("nvmet-tcp: Fix a kernel panic when host sends an invalid H2C PDU length") Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The new version causes a different warning with some compiler versions, notably
gcc-9 and gcc-10, and also misses the zero padding that was apparently done
intentionally in the original code:
drivers/nvme/target/trace.h:56:2: error: 'strncpy' specified bound depends on the length of the source argument [-Werror=stringop-overflow=]
Change it to use strscpy_pad() with the original length, which will give
a properly padded and zero-terminated string as well as avoiding the warning.
Fixes: d86481e924a7 ("nvmet: use min of device_path and disk len") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
For Gen1 isoc-in transfer, host still send out unexpected ACK after device
finish the burst with a short packet, this will cause an exception on the
connected device, such as, a usb 4k camera.
It can be fixed by setting rxfifo depth less than 4k bytes, prefer to use
3k here, the side-effect is that may cause performance drop about 10%,
including bulk transfer.
Fixes: 926d60ae64a6 ("usb: xhci-mtk: modify the SOF/ITP interval for mt8195") Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Link: https://lore.kernel.org/r/20240104061640.7335-2-chunfeng.yun@mediatek.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
a string ":samba-dcerpcd" is unpacked as a fully-qualified name and then
passed to aa_splitn_fqname().
aa_splitn_fqname() treats ":samba-dcerpcd" as only containing a namespace.
Thus it returns NULL for tmpname, meanwhile tmpns is non-NULL. Later
aa_alloc_profile() crashes as the new profile name is NULL now.
general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] PREEMPT SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 6 PID: 1657 Comm: apparmor_parser Not tainted 6.7.0-rc2-dirty #16
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
RIP: 0010:strlen+0x1e/0xa0
Call Trace:
<TASK>
? strlen+0x1e/0xa0
aa_policy_init+0x1bb/0x230
aa_alloc_profile+0xb1/0x480
unpack_profile+0x3bc/0x4960
aa_unpack+0x309/0x15e0
aa_replace_profiles+0x213/0x33c0
policy_update+0x261/0x370
profile_replace+0x20e/0x2a0
vfs_write+0x2af/0xe00
ksys_write+0x126/0x250
do_syscall_64+0x46/0xf0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
</TASK>
---[ end trace 0000000000000000 ]---
RIP: 0010:strlen+0x1e/0xa0
It seems such behaviour of aa_splitn_fqname() is expected and checked in
other places where it is called (e.g. aa_remove_profiles). Well, there
is an explicit comment "a ns name without a following profile is allowed"
inside.
AFAICS, nothing can prevent unpacked "name" to be in form like
":samba-dcerpcd" - it is passed from userspace.
Deny the whole profile set replacement in such case and inform user with
EPROTO and an explaining message.
Found by Linux Verification Center (linuxtesting.org).
Add variants of perf_env__insert_bpf_prog_info(), perf_env__insert_btf()
and perf_env__find_btf prefixed with __ to indicate the
env->bpf_progs.lock is assumed held.
Call these variants when the lock is held to avoid recursively taking it
and potentially having a thread deadlock with itself.
Fixes: f8dfeae009effc0b ("perf bpf: Show more BPF program info in print_bpf_prog_info()") Signed-off-by: Ian Rogers <irogers@google.com> Acked-by: Jiri Olsa <jolsa@kernel.org> Acked-by: Song Liu <song@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Huacai Chen <chenhuacai@kernel.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: K Prateek Nayak <kprateek.nayak@amd.com> Cc: Kan Liang <kan.liang@linux.intel.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ming Wang <wangming01@loongson.cn> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ravi Bangoria <ravi.bangoria@amd.com> Link: https://lore.kernel.org/r/20231207014655.1252484-1-irogers@google.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
in nvmet_tcp_handle_h2c_data_pdu(), if the host sends a data_offset
different from rbytes_done, the driver ends up calling nvmet_req_complete()
passing a status error.
The problem is that at this point cmd->req is not yet initialized,
the kernel will crash after dereferencing a NULL pointer.
Fix the bug by replacing the call to nvmet_req_complete() with
nvmet_tcp_fatal_error().
Fixes: 872d26a391da ("nvmet-tcp: add NVMe over TCP target driver") Reviewed-by: Keith Busch <kbsuch@kernel.org> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Maurizio Lombardi <mlombard@redhat.com> Signed-off-by: Keith Busch <kbusch@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
If the host sends an H2CData command with an invalid DATAL,
the kernel may crash in nvmet_tcp_build_pdu_iovec().
Unable to handle kernel NULL pointer dereference at
virtual address 0000000000000000
lr : nvmet_tcp_io_work+0x6ac/0x718 [nvmet_tcp]
Call trace:
process_one_work+0x174/0x3c8
worker_thread+0x2d0/0x3e8
kthread+0x104/0x110
Fix the bug by raising a fatal error if DATAL isn't coherent
with the packet size.
Also, the PDU length should never exceed the MAXH2CDATA parameter which
has been communicated to the host in nvmet_tcp_handle_icreq().
In ACM support for sending breaks to devices is optional.
If a device says that it doenot support sending breaks,
the host must respect that.
Given the number of optional features providing tty operations
for each combination is not practical and errors need to be
returned dynamically if unsupported features are requested.
In case a device does not support break, we want the tty layer
to treat that like it treats drivers that statically cannot
support sending a break. It ignores the inability and does nothing.
This patch uses EOPNOTSUPP to indicate that.
If the driver sets TTY_DRIVER_HARDWARE_BREAK, we leave ops->break_ctl()
to the driver and return from send_break(). But we do it using a local
variable and keep the code flowing through the end of the function.
Instead, do 'return' immediately with the ops->break_ctl()'s return
value.
This way, we don't have to stuff the 'else' branch of the 'if' with the
software break handling. And we can re-indent the function too.
which does not make sense. Moreover, when trying to set a new scale we
get an error because there's no call to __ad9467_get_scale() to give us
values as given when reading in_voltage_scale. Fix it by computing the
available scales during probe and properly pass the list when
.read_available() is called.
While at it, change to use .read_available() from iio_info. Also note
that to properly fix this, adi-axi-adc.c has to be changed accordingly.
Fixes: ad6797120238 ("iio: adc: ad9467: add support AD9467 ADC") Signed-off-by: Nuno Sa <nuno.sa@analog.com> Reviewed-by: David Lechner <dlechner@baylibre.com> Link: https://lore.kernel.org/r/20231207-iio-backend-prep-v2-4-a4a33bc4d70e@analog.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The reset gpio was being handled with inverted polarity. This means that
as far as gpiolib is concerned we were actually leaving the pin asserted
(in theory, this would mean reset). However, inverting the polarity in
devicetree made things work. Fix it by doing it the proper way and how
gpiolib expects it to be done.
While at it, moved the handling to it's own function and dropped
'reset_gpio' from the 'struct ad9467_state' as we only need it during
probe. On top of that, refactored things so that we now request the gpio
asserted (i.e in reset) and then de-assert it. Also note that we now use
gpiod_set_value_cansleep() instead of gpiod_direction_output() as we
already request the pin as output.
Fixes: ad6797120238 ("iio: adc: ad9467: add support AD9467 ADC") Reviewed-by: David Lechner <dlechner@baylibre.com> Signed-off-by: Nuno Sa <nuno.sa@analog.com> Link: https://lore.kernel.org/r/20231207-iio-backend-prep-v2-1-a4a33bc4d70e@analog.com Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When building whole selftests on arm64, rsync gives an erorr about sgx:
rsync: [sender] link_stat "/root/linux-next/tools/testing/selftests/sgx/test_encl.elf" failed: No such file or directory (2)
rsync error: some files/attrs were not transferred (see previous errors) (code 23) at main.c(1327) [sender=3.2.5]
The root casue is sgx only used on X86_64, and shall be skipped on other
platforms.
Fix this by moving TEST_CUSTOM_PROGS and TEST_FILES inside the if check,
then the build result will be "Skipping non-existent dir: sgx".
Fixes: 2adcba79e69d ("selftests/x86: Add a selftest for SGX") Signed-off-by: Zhao Mengmeng <zhaomengmeng@kylinos.cn> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Link: https://lore.kernel.org/all/20231206025605.3965302-1-zhaomzhao%40126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
Ensure ctx is zero-initialized, such that the encl_measure function will
not call EVP_MD_CTX_destroy with an uninitialized ctx pointer in case of an
early error during key generation.
Fixes: 2adcba79e69d ("selftests/x86: Add a selftest for SGX") Signed-off-by: Jo Van Bulck <jo.vanbulck@cs.kuleuven.be> Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com> Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org> Acked-by: Kai Huang <kai.huang@intel.com> Link: https://lore.kernel.org/all/20231005153854.25566-2-jo.vanbulck%40cs.kuleuven.be Signed-off-by: Sasha Levin <sashal@kernel.org>
When using the serial port as RS485 port, the tx statemachine is used to
control the RTS pin to drive the RS485 transceiver TX_EN pin. When the
TTY port is closed in the middle of a transmission (for instance during
userland application crash), imx_uart_shutdown disables the interface
and disables the Transmission Complete interrupt. afer that,
imx_uart_stop_tx bails on an incomplete transmission, to be retriggered
by the TC interrupt. This interrupt is disabled and therefore the tx
statemachine never transitions out of SEND. The statemachine is in
deadlock now, and the TX_EN remains low, making the interface useless.
imx_uart_stop_tx now checks for incomplete transmission AND whether TC
interrupts are enabled before bailing to be retriggered. This makes sure
the state machine handling is reached, and is properly set to
WAIT_AFTER_SEND.
Returning an error code from .remove() makes the driver core emit the
little helpful error message:
remove callback returned a non-zero value. This will be ignored.
and then remove the device anyhow. So all resources that were not freed
are leaked in this case. Skipping serial8250_unregister_port() has the
potential to keep enough of the UART around to trigger a use-after-free.
So replace the error return (and with it the little helpful error
message) by a more useful error message and continue to cleanup.
RRT_ALRT register holds remaining battery time in minutes therefore it
needs to be scaled accordingly when exposing TIME_TO_EMPTY via sysfs
expressed in seconds
Fixes: b4c7715c10c1 ("power: supply: add CellWise cw2015 fuel gauge driver") Signed-off-by: Jan Palus <jpalus@fastmail.com> Link: https://lore.kernel.org/r/20231111221704.5579-1-jpalus@fastmail.com Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
After unloading a module, we must reset the linear mapping permissions,
see the example below:
Before unloading a module:
0xffffaf809d65d000-0xffffaf809d6dc000 0x000000011d65d000 508K PTE . .. .. D A G . . W R V
0xffffaf809d6dc000-0xffffaf809d6dd000 0x000000011d6dc000 4K PTE . .. .. D A G . . . R V
0xffffaf809d6dd000-0xffffaf809d6e1000 0x000000011d6dd000 16K PTE . .. .. D A G . . W R V
0xffffaf809d6e1000-0xffffaf809d6e7000 0x000000011d6e1000 24K PTE . .. .. D A G . X . R V
After unloading a module:
0xffffaf809d65d000-0xffffaf809d6e1000 0x000000011d65d000 528K PTE . .. .. D A G . . W R V
0xffffaf809d6e1000-0xffffaf809d6e7000 0x000000011d6e1000 24K PTE . .. .. D A G . X W R V
The last mapping is not reset and we end up with WX mappings in the linear
mapping.
So add VM_FLUSH_RESET_PERMS to our module_alloc() definition.
Fixes: 0cff8bff7af8 ("riscv: avoid the PIC offset of static percpu data in module beyond 2G limits") Signed-off-by: Alexandre Ghiti <alexghiti@rivosinc.com> Link: https://lore.kernel.org/r/20231213134027.155327-2-alexghiti@rivosinc.com Signed-off-by: Palmer Dabbelt <palmer@rivosinc.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
max_low_pfn variable is incorrectly adjusted if the kernel is built with
high memory support and the later is detected in a running system, so the
memory which actually can be directly mapped is getting into the highmem
zone. See the ZONE_NORMAL range on my MIPS32r5 system:
> Zone ranges:
> DMA [mem 0x0000000000000000-0x0000000000ffffff]
> Normal [mem 0x0000000001000000-0x0000000007ffffff]
> HighMem [mem 0x0000000008000000-0x000000020fffffff]
while the zones are supposed to look as follows:
> Zone ranges:
> DMA [mem 0x0000000000000000-0x0000000000ffffff]
> Normal [mem 0x0000000001000000-0x000000001fffffff]
> HighMem [mem 0x0000000020000000-0x000000020fffffff]
Even though the physical memory within the range [0x08000000;0x20000000]
belongs to MMIO on our system, we don't really want it to be considered as
high memory since on MIPS32 that range still can be directly mapped.
Note there might be other problems caused by the max_low_pfn variable
misconfiguration. For instance high_memory variable is initialize with
virtual address corresponding to the max_low_pfn PFN, and by design it
must define the upper bound on direct map memory, then end of the normal
zone. That in its turn potentially may cause problems in accessing the
memory by means of the /dev/mem and /dev/kmem devices.
Let's fix the discovered misconfiguration then. It turns out the commit a94e4f24ec83 ("MIPS: init: Drop boot_mem_map") didn't introduce the
max_low_pfn adjustment quite correct. If the kernel is built with high
memory support and the system is equipped with high memory, the
max_low_pfn variable will need to be initialized with PFN of the most
upper directly reachable memory address so the zone normal would be
correctly setup. On MIPS that PFN corresponds to PFN_DOWN(HIGHMEM_START).
If the system is built with no high memory support and one is detected in
the running system, we'll just need to adjust the max_pfn variable to
discard the found high memory from the system and leave the max_low_pfn as
is, since the later will be less than PFN_DOWN(HIGHMEM_START) anyway by
design of the for_each_memblock() loop performed a bit early in the
bootmem_init() method.
Fixes: a94e4f24ec83 ("MIPS: init: Drop boot_mem_map") Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
dmi_early_remap() has been defined as ioremap_cache() which on MIPS32 gets
to be converted to the VM-based mapping. DMI early remapping is performed
at the setup_arch() stage with no VM available. So calling the
dmi_early_remap() for MIPS32 causes the system to crash at the early boot
time. Fix that by converting dmi_early_remap() to the uncached remapping
which is always available on both 32 and 64-bits MIPS systems.
Note this change shall not cause any regressions on the current DMI
support implementation because on the early boot-up stage neither MIPS32
nor MIPS64 has the cacheable ioremapping support anyway.
Fixes: be8fa1cb444c ("MIPS: Add support for Desktop Management Interface (DMI)") Signed-off-by: Serge Semin <fancer.lancer@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The conversion to CLK_FRAC_DIVIDER_POWER_OF_TWO_PS uses wrong flags
in the parameters and hence miscalculates the values in the clock
divider. Fix this by applying the flag to the proper parameter.
Fixes: 82f53f9ee577 ("clk: fractional-divider: Introduce POWER_OF_TWO_PS flag") Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reported-by: Alex Vinarskis <alex.vinarskis@gmail.com> Link: https://lore.kernel.org/r/20231211111441.3910083-1-andriy.shevchenko@linux.intel.com Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The AW2013 driver uses devm_regmap_init_i2c, so REGMAP_I2C needs to
be selected.
Otherwise build process may fail with:
ld: drivers/leds/leds-aw2013.o: in function `aw2013_probe':
leds-aw2013.c:345: undefined reference to `__devm_regmap_init_i2c'
kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Fixes: e15d7f2b81d2 ("mfd: syscon: Use a unique name with regmap_config") Signed-off-by: Kunwu Chan <chentao@kylinos.cn> Reviewed-by: Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20231204092443.2462115-1-chentao@kylinos.cn Signed-off-by: Lee Jones <lee@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When commit 82612d66d51d ("iommu: Allow the dma-iommu api to
use bounce buffers") was introduced, it did not add the logic
for tracing the bounce buffer usage from iommu_dma_map_page().
All of the users of swiotlb_tbl_map_single() trace their bounce
buffer usage, except iommu_dma_map_page(). This makes it difficult
to track SWIOTLB usage from that function. Thus, trace bounce buffer
usage from iommu_dma_map_page().
Fixes: 82612d66d51d ("iommu: Allow the dma-iommu api to use bounce buffers") Cc: stable@vger.kernel.org # v5.15+ Cc: Tom Murphy <murphyt7@tcd.ie> Cc: Lu Baolu <baolu.lu@linux.intel.com> Cc: Saravana Kannan <saravanak@google.com> Signed-off-by: Isaac J. Manjarres <isaacmanjarres@google.com> Link: https://lore.kernel.org/r/20231208234141.2356157-1-isaacmanjarres@google.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Isaac J. Manjarres <isaacmanjarres@google.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added") Cc: <stable@vger.kernel.org> Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com> Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There appear to be a few different ways that Wacom devices can deal with
confidence:
1. If the device looses confidence in a touch, it will first clear
the tipswitch flag in one report, and then clear the confidence
flag in a second report. This behavior is used by e.g. DTH-2452.
2. If the device looses confidence in a touch, it will clear both
the tipswitch and confidence flags within the same report. This
behavior is used by some AES devices.
3. If the device looses confidence in a touch, it will clear *only*
the confidence bit. The tipswitch bit will remain set so long as
the touch is tracked. This behavior may be used in future devices.
The driver does not currently handle situation 3 properly. Touches that
loose confidence will remain "in prox" and essentially frozen in place
until the tipswitch bit is finally cleared. Not only does this result
in userspace seeing a stuck touch, but it also prevents pen arbitration
from working properly (the pen won't send events until all touches are
up, but we don't currently process events from non-confident touches).
This commit centralizes the checking of the confidence bit in the
wacom_wac_finger_slot() function and has 'prox' depend on it. In the
case where situation 3 is encountered, the treat the touch as though
it was removed, allowing both userspace and the pen arbitration to
act normally.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com> Signed-off-by: Ping Cheng <ping.cheng@wacom.com> Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com> Fixes: 7fb0413baa7f ("HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts") Cc: stable@vger.kernel.org Signed-off-by: Jiri Kosina <jkosina@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previous version of ad7091r event handler received the ADC state pointer
and retrieved the iio device from driver data field with dev_get_drvdata().
However, no driver data have ever been set, which led to null pointer
dereference when running the event handler.
Pass the iio device to the event handler and retrieve the ADC state struct
from it so we avoid the null pointer dereference and save the driver from
filling the driver data field.
There is a potential UAF scenario in the case of an LPI translation
cache hit racing with an operation that invalidates the cache, such
as a DISCARD ITS command. The root of the problem is that
vgic_its_check_cache() does not elevate the refcount on the vgic_irq
before dropping the lock that serializes refcount changes.
Have vgic_its_check_cache() raise the refcount on the returned vgic_irq
and add the corresponding decrement after queueing the interrupt.
When the VMM writes to ISPENDR0 to set the state pending state of
an SGI, we fail to convey this to the HW if this SGI is already
backed by a GICv4.1 vSGI.
This is a bit of a corner case, as this would only occur if the
vgic state is changed on an already running VM, but this can
apparently happen across a guest reset driven by the VMM.
Fix this by always writing out the pending_latch value to the
HW, and reseting it to false.
kvm_guest_cpu_offline() tries to disable kvmclock regardless if it is
present in the VM. It leads to write to a MSR that doesn't exist on some
configurations, namely in TDX guest:
unchecked MSR access error: WRMSR to 0x12 (tried to write 0x0000000000000000)
at rIP: 0xffffffff8110687c (kvmclock_disable+0x1c/0x30)
kvmclock enabling is gated by CLOCKSOURCE and CLOCKSOURCE2 KVM paravirt
features.
Do not disable kvmclock if it was not enabled.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Fixes: c02027b5742b ("x86/kvm: Disable kvmclock on all CPUs on shutdown") Reviewed-by: Sean Christopherson <seanjc@google.com> Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Wanpeng Li <wanpengli@tencent.com> Cc: stable@vger.kernel.org
Message-Id: <20231205004510.27164-6-kirill.shutemov@linux.intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We found a failure when using the iperf tool during WiFi performance
testing, where some MSIs were received while clearing the interrupt
status, and these MSIs cannot be serviced.
The interrupt status can be cleared even if the MSI status remains pending.
As such, given the edge-triggered interrupt type, its status should be
cleared before being dispatched to the handler of the underling device.
[kwilczynski: commit log, code comment wording] Link: https://lore.kernel.org/linux-pci/20231211094923.31967-1-jianjun.wang@mediatek.com Fixes: 43e6409db64d ("PCI: mediatek: Add MSI support for MT2712 and MT7622") Signed-off-by: qizhong cheng <qizhong.cheng@mediatek.com> Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: rewrap comment] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Cc: <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6f5e193bfb55 ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org Fixes: 6f5e193bfb55 ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address") Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com> Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org> Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Cc: stable@vger.kernel.org # 5.7 Cc: Kishon Vijay Abraham I <kishon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AP BSSID configuration is missing at AP start. Without this fix, FW returns
STA interface MAC address after first init. When hostapd restarts, it gets MAC
address from netdev before driver sets STA MAC to netdev again. Now MAC address
between hostapd and net interface are different causes STA cannot connect to
AP. After that MAC address of uap0 mlan0 become the same. And issue disappears
after following hostapd restart (another issue is AP/STA MAC address become the
same).
This patch fixes the issue cleanly.
Signed-off-by: David Lin <yu-hao.lin@nxp.com> Fixes: 12190c5d80bd ("mwifiex: add cfg80211 start_ap and stop_ap handlers") Cc: stable@vger.kernel.org Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com> Tested-by: Rafael Beims <rafael.beims@toradex.com> # Verdin iMX8MP/SD8997 SD Acked-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://msgid.link/20231215005118.17031-1-yu-hao.lin@nxp.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The rtlwifi driver comes with custom code to write into PCIe Link
Control register. RMW access for the Link Control register requires
locking that is already provided by the standard PCIe capability
accessors.
Convert the custom RMW code writing into LNKCTL register to standard
RMW capability accessors. The accesses are changed to cover the full
LNKCTL register instead of touching just a single byte of the register.
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver") Cc: stable@vger.kernel.org Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20231124084725.12738-3-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ever since introduction in the commit 0c8173385e54 ("rtl8192ce: Add new
driver") the rtlwifi code has, according to comments, attempted to
disable/enable ASPM of the upstream bridge by writing into its LNKCTL
register. However, the code has never been correct because it performs
the writes to the device instead of the upstream bridge.
Worse yet, the offset where the PCIe capabilities reside is derived
from the offset of the upstream bridge. As a result, the write will use
an offset on the device that does not relate to the LNKCTL register
making the ASPM disable/enable code outright dangerous.
Because of those problems, there is no indication that the driver needs
disable/enable ASPM on the upstream bridge. As the Capabilities offset
is not correctly calculated for the write to target device's LNKCTL
register, the code is not disabling/enabling device's ASPM either.
Therefore, just remove the upstream bridge related ASPM disable/enable
code entirely.
The upstream bridge related ASPM code was the only user of the struct
mp_adapter members num4bytes, pcibridge_pciehdr_offset, and
pcibridge_linkctrlreg so those are removed as well.
Note: This change does not remove the code related to changing the
device's ASPM on purpose (which is independent of this flawed code
related to upstream bridge's ASPM).
Suggested-by: Bjorn Helgaas <bhelgaas@kernel.org> Fixes: 0c8173385e54 ("rtl8192ce: Add new driver") Fixes: 886e14b65a8f ("rtlwifi: Eliminate raw reads and writes from PCIe portion") Cc: stable@vger.kernel.org Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20231124084725.12738-2-ilpo.jarvinen@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 495184ac91bb ("mt76: mt7915: add support for applying
pre-calibration data") was fundamentally broken and never worked.
The idea (before NVMEM support) was to expand the MTD function and pass
an additional offset. For normal EEPROM load the offset would always be
0. For the purpose of precal loading, an offset was passed that was
internally the size of EEPROM, since precal data is right after the
EEPROM.
Problem is that the offset value passed is never handled and is actually
overwrite by
offset = be32_to_cpup(list);
ret = mtd_read(mtd, offset, len, &retlen, eep);
resulting in the passed offset value always ingnored. (and even passing
garbage data as precal as the start of the EEPROM is getting read)
Fix this by adding to the current offset value, the offset from DT to
correctly read the piece of data at the requested location.
Cc: stable@vger.kernel.org Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data") Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some cases the firmware expects cbndx 1 to be assigned to the GMU,
so we also want the default domain for the GMU to be an identy domain.
This way it does not get a context bank assigned. Without this, both
of_dma_configure() and drm/msm's iommu_domain_attach() will trigger
allocating and configuring a context bank. So GMU ends up attached to
both cbndx 1 and later cbndx 2. This arrangement seemingly confounds
and surprises the firmware if the GPU later triggers a translation
fault, resulting (on sc8280xp / lenovo x13s, at least) in the SMMU
getting wedged and the GPU stuck without memory access.
Cc: stable@vger.kernel.org Signed-off-by: Rob Clark <robdclark@chromium.org> Tested-by: Johan Hovold <johan+linaro@kernel.org> Reviewed-by: Robin Murphy <robin.murphy@arm.com> Link: https://lore.kernel.org/r/20231210180655.75542-1-robdclark@gmail.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following case can cause a crash due to missing attach_btf:
1) load rawtp program
2) load fentry program with rawtp as target_fd
3) create tracing link for fentry program with target_fd = 0
4) repeat 3
In the end we have:
- prog->aux->dst_trampoline == NULL
- tgt_prog == NULL (because we did not provide target_fd to link_create)
- prog->aux->attach_btf == NULL (the program was loaded with attach_prog_fd=X)
- the program was loaded for tgt_prog but we have no way to find out which one
projects / linux-stable / log