If we delay sending End Transfer for Setup TRB to be prepared, we need
to check if the End Transfer was in preparation for a driver
teardown/soft-disconnect. In those cases, just send the End Transfer
command without delay.
In the case of soft-disconnect, there's a very small chance the command
may not go through immediately. But should it happen, the Setup TRB will
be prepared during the polling of the controller halted state, allowing
the command to go through then.
In the case of disabling endpoint due to reconfiguration (e.g.
set_interface(alt-setting) or usb reset), then it's driven by the host.
Typically the host wouldn't immediately cancel the control request and
send another control transfer to trigger the End Transfer command
timeout.
The rkisp1 does share interrupt lines on some platforms, after all. Thus
we need to revert this, and implement a fix for the rkisp1 shared irq
handling in a follow-up patch.
Do not call gadget stop until the poll for controller halt is
completed. DEVTEN is cleared as part of gadget stop, so the intention to
allow ep0 events to continue while waiting for controller halt is not
happening.
The gadget driver may wait on the request completion when it sets the
USB_GADGET_DELAYED_STATUS. Make sure that the End Transfer command can
go through if the dwc->delayed_status is set so that the request can
complete. When the delayed_status is set, the Setup packet is already
processed, and the next phase should be either Data or Status. It's
unlikely that the host would cancel the control transfer and send a new
Setup packet during End Transfer command. But if that's the case, we can
try again when ep0state returns to EP0_SETUP_PHASE.
The fbtft_framebuffer_alloc() calls fb_deferred_io_init() before
initializing info->fix.smem_len. It is set to zero by the
framebuffer_alloc() function. It will trigger a WARN_ON() at the
start of fb_deferred_io_init() and the function will not do anything.
The kernel is globally removing the ambiguous 0-length and 1-element
arrays in favor of flexible arrays, so that we can gain both compile-time
and run-time array bounds checking[1].
Replace the trailing 1-element array with a flexible array in the
following structures:
Replace the trailing 1-element array with a flexible array, but leave
the existing structure padding:
struct smb2_file_all_info
struct smb2_lock_req
Adjust all related size calculations to match the changes to sizeof().
No machine code output or .data section differences are produced after
these changes.
[1] For lots of details, see both:
https://docs.kernel.org/process/deprecated.html#zero-length-and-one-element-arrays
https://people.kernel.org/kees/bounded-flexible-arrays-in-c
Cc: Steve French <sfrench@samba.org> Cc: Paulo Alcantara <pc@cjr.nz> Cc: Ronnie Sahlberg <lsahlber@redhat.com> Cc: Shyam Prasad N <sprasad@microsoft.com> Cc: Tom Talpey <tom@talpey.com> Cc: Namjae Jeon <linkinjeon@kernel.org> Cc: Sergey Senozhatsky <senozhatsky@chromium.org> Cc: linux-cifs@vger.kernel.org Cc: samba-technical@lists.samba.org Reviewed-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Vasiliy Kovalev <kovalev@altlinux.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
libbpf support for "tc" progs doesn't exist for the linux-5.15.y tree.
This commit was backported too far back in upstream, to a kernel where
the libbpf support was not there for the test.
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
>From grepping code, it's clear that many people aren't aware of the
need to call pm_runtime_dont_use_autosuspend().
When brainstorming solutions, one idea that came up was to leverage
the new-ish devm_pm_runtime_enable() function. The idea here is that:
* When the devm action is called we know that the driver is being
removed. It's the perfect time to undo the use_autosuspend.
* The code of pm_runtime_dont_use_autosuspend() already handles the
case of being called when autosuspend wasn't enabled.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Stable-dep-of: 3d07a411b4fa ("drm/msm/dsi: Use pm_runtime_resume_and_get to prevent refcnt leaks") Signed-off-by: Amit Pundir <amit.pundir@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the MIDR value of Microsoft Azure Cobalt 100, which is a Microsoft
implemented CPU based on r0p0 of the ARM Neoverse N2 CPU, and therefore
suffers from all the same errata.
CC: stable@vger.kernel.org # 5.15+ Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com> Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com> Acked-by: Mark Rutland <mark.rutland@arm.com> Acked-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Oliver Upton <oliver.upton@linux.dev> Link: https://lore.kernel.org/r/20240214175522.2457857-1-eahariha@linux.microsoft.com Signed-off-by: Will Deacon <will@kernel.org> Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If DAT metadata file block access fails due to corruption of the DAT file
or abnormal virtual block numbers held by b-trees or inodes, a kernel
warning is generated.
This replaces the WARN_ONs by error output, so that a kernel, booted with
panic_on_warn, does not panic. This patch also replaces the detected
return code -ENOENT with another internal code -EINVAL to notify the bmap
layer of metadata corruption. When the bmap layer sees -EINVAL, it
handles the abnormal situation with nilfs_bmap_convert_error() and finally
returns code -EIO as it should.
According to a syzbot report, end_buffer_async_write(), which handles the
completion of block device writes, may detect abnormal condition of the
buffer async_write flag and cause a BUG_ON failure when using nilfs2.
Nilfs2 itself does not use end_buffer_async_write(). But, the async_write
flag is now used as a marker by commit 7f42ec394156 ("nilfs2: fix issue
with race condition of competition between segments for dirty blocks") as
a means of resolving double list insertion of dirty blocks in
nilfs_lookup_dirty_data_buffers() and nilfs_lookup_node_buffers() and the
resulting crash.
This modification is safe as long as it is used for file data and b-tree
node blocks where the page caches are independent. However, it was
irrelevant and redundant to also introduce async_write for segment summary
and super root blocks that share buffers with the backing device. This
led to the possibility that the BUG_ON check in end_buffer_async_write
would fail as described above, if independent writebacks of the backing
device occurred in parallel.
The use of async_write for segment summary buffers has already been
removed in a previous change.
Fix this issue by removing the manipulation of the async_write flag for
the remaining super root block buffer.
Link: https://lkml.kernel.org/r/20240203161645.4992-1-konishi.ryusuke@gmail.com Fixes: 7f42ec394156 ("nilfs2: fix issue with race condition of competition between segments for dirty blocks") Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: syzbot+5c04210f7c7f897c1e7f@syzkaller.appspotmail.com Closes: https://lkml.kernel.org/r/00000000000019a97c05fd42f8c8@google.com Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some systems, sys_membarrier can be very expensive, causing overall
slowdowns for everything. So put a lock on the path in order to
serialize the accesses to prevent the ability for this to be called at
too high of a frequency and saturate the machine.
Reviewed-and-tested-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Acked-by: Borislav Petkov <bp@alien8.de> Fixes: 22e4ebb97582 ("membarrier: Provide expedited private command") Fixes: c5f58bd58f43 ("membarrier: Provide GLOBAL_EXPEDITED command") Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[ converted to explicit mutex_*() calls - cleanup.h is not in this stable
branch - gregkh ] Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch fdb8e12cc2cc ("netfilter: ipset: fix performance regression
in swap operation") missed to add the calls to gc cancellations
at the error path of create operations and at module unload. Also,
because the half of the destroy operations now executed by a
function registered by call_rcu(), neither NFNL_SUBSYS_IPSET mutex
or rcu read lock is held and therefore the checking of them results
false warnings.
While in theory the timer can be triggered before expires + delta, for the
cases of RT tasks they really have no business giving any lenience for
extra slack time, so override any passed value by the user and always use
zero for schedule_hrtimeout_range() calls. Furthermore, this is similar to
what the nanosleep(2) family already does with current->timer_slack_ns.
Signed-off-by: Davidlohr Bueso <dave@stgolabs.net> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Link: https://lore.kernel.org/r/20230123173206.6764-3-dave@stgolabs.net Signed-off-by: Felix Moessbauer <felix.moessbauer@siemens.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch "netfilter: ipset: fix race condition between swap/destroy
and kernel side add/del/test", commit 28628fa9 fixes a race condition.
But the synchronize_rcu() added to the swap function unnecessarily slows
it down: it can safely be moved to destroy and use call_rcu() instead.
Eric Dumazet pointed out that simply calling the destroy functions as
rcu callback does not work: sets with timeout use garbage collectors
which need cancelling at destroy which can wait. Therefore the destroy
functions are split into two: cancelling garbage collectors safely at
executing the command received by netlink and moving the remaining
part only into the rcu callback.
Link: https://lore.kernel.org/lkml/C0829B10-EAA6-4809-874E-E1E9C05A8D84@automattic.com/ Fixes: 28628fa952fe ("netfilter: ipset: fix race condition between swap/destroy and kernel side add/del/test") Reported-by: Ale Crismani <ale.crismani@automattic.com> Reported-by: David Wang <00107082@163.com> Tested-by: David Wang <00107082@163.com> Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GNU's addr2line can have problems parsing a vmlinux built with LLVM,
particularly when LTO was used. In order to decode the traces correctly
this patch adds the ability to switch to LLVM's utilities readelf and
addr2line. The same approach is followed by Will in [1].
Note that one could set CROSS_COMPILE=llvm- instead to hack around this
issue. However, doing so can break the decodecode routine as it will
force the selection of other LLVM utilities down the line e.g. llvm-as.
When framebuffer gets closed, the queued deferred IO gets cancelled. This
can cause some last display data to vanish. This is problematic for users
who send a still image to the framebuffer, then close the file: the image
may never appear.
To ensure none of display data get lost, flush the queued deferred IO
first before closing.
Another possible solution is to delete the cancel_delayed_work_sync()
instead. The difference is that the display may appear some time after
closing. However, the clearing of page mapping after this needs to be
removed too, because the page mapping is used by the deferred work. It is
not completely obvious whether it is okay to not clear the page mapping.
For a patch intended for stable trees, go with the simple and obvious
solution.
Fixes: 60b59beafba8 ("fbdev: mm: Deferred IO support") Cc: stable@vger.kernel.org Signed-off-by: Nam Cao <namcao@linutronix.de> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Helge Deller <deller@gmx.de> Signed-off-by: Sasha Levin <sashal@kernel.org>
The recent fix for the deferred I/O by the commit 3efc61d95259 ("fbdev: Fix invalid page access after closing deferred I/O devices")
caused a regression when the same fb device is opened/closed while
it's being used. It resulted in a frozen screen even if something
is redrawn there after the close. The breakage is because the patch
was made under a wrong assumption of a single open; in the current
code, fb_deferred_io_release() cleans up the page mapping of the
pageref list and it calls cancel_delayed_work_sync() unconditionally,
where both are no correct behavior for multiple opens.
This patch adds a refcount for the opens of the device, and applies
the cleanup only when all files get closed.
As both fb_deferred_io_open() and _close() are called always in the
fb_info lock (mutex), it's safe to use the normal int for the
refcounting.
When a fbdev with deferred I/O is once opened and closed, the dirty
pages still remain queued in the pageref list, and eventually later
those may be processed in the delayed work. This may lead to a
corruption of pages, hitting an Oops.
This patch makes sure to cancel the delayed work and clean up the
pageref list at closing the device for addressing the bug. A part of
the cleanup code is factored out as a new helper function that is
called from the common fb_release().
Rename various instances of pagelist to pagereflist. The list now
stores pageref structures, so the new name is more appropriate.
In their write-back helpers, several fbdev drivers refer to the
pageref list in struct fb_deferred_io instead of using the one
supplied as argument to the function. Convert them over to the
supplied one. It's the same instance, so no change of behavior
occurs.
Store the per-page state for fbdev's deferred I/O in struct
fb_deferred_io_pageref. Maintain a list of pagerefs for the pages
that have to be written back to video memory. Update all affected
drivers.
As with pages before, fbdev acquires a pageref when an mmaped page
of the framebuffer is being written to. It holds the pageref in a
list of all currently written pagerefs until it flushes the written
pages to video memory. Writeback occurs periodically. After writeback
fbdev releases all pagerefs and builds up a new dirty list until the
next writeback occurs.
Using pagerefs has a number of benefits.
For pages of the framebuffer, the deferred I/O code used struct
page.lru as an entry into the list of dirty pages. The lru field is
owned by the page cache, which makes deferred I/O incompatible with
some memory pages (e.g., most notably DRM's GEM SHMEM allocator).
struct fb_deferred_io_pageref now provides an entry into a list of
dirty framebuffer pages, freeing lru for use with the page cache.
Drivers also assumed that struct page.index is the page offset into
the framebuffer. This is not true for DRM buffers, which are located
at various offset within a mapped area. struct fb_deferred_io_pageref
explicitly stores an offset into the framebuffer. struct page.index
is now only the page offset into the mapped area.
These changes will allow DRM to use fbdev deferred I/O without an
intermediate shadow buffer.
v3:
* use pageref->offset for sorting
* fix grammar in comment
v2:
* minor fixes in commit message
Easily hit the below list corruption:
==
list_add corruption. prev->next should be next (ffffffffc0ceb090), but
was ffffec604507edc8. (prev=ffffec604507edc8).
WARNING: CPU: 65 PID: 3959 at lib/list_debug.c:26
__list_add_valid+0x53/0x80
CPU: 65 PID: 3959 Comm: fbdev Tainted: G U
RIP: 0010:__list_add_valid+0x53/0x80
Call Trace:
<TASK>
fb_deferred_io_mkwrite+0xea/0x150
do_page_mkwrite+0x57/0xc0
do_wp_page+0x278/0x2f0
__handle_mm_fault+0xdc2/0x1590
handle_mm_fault+0xdd/0x2c0
do_user_addr_fault+0x1d3/0x650
exc_page_fault+0x77/0x180
? asm_exc_page_fault+0x8/0x30
asm_exc_page_fault+0x1e/0x30
RIP: 0033:0x7fd98fc8fad1
==
Figure out the race happens when one process is adding &page->lru into
the pagelist tail in fb_deferred_io_mkwrite(), another process is
re-initializing the same &page->lru in fb_deferred_io_fault(), which is
not protected by the lock.
This fix is to init all the page lists one time during initialization,
it not only fixes the list corruption, but also avoids INIT_LIST_HEAD()
redundantly.
V2: change "int i" to "unsigned int i" (Geert Uytterhoeven)
Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com> Fixes: 105a940416fc ("fbdev/defio: Early-out if page is already enlisted") Cc: Thomas Zimmermann <tzimmermann@suse.de> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Reviewed-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220318005003.51810-1-chuansheng.liu@intel.com
Stable-dep-of: 33cd6ea9c067 ("fbdev: flush deferred IO before closing") Signed-off-by: Sasha Levin <sashal@kernel.org>
Fbdev's deferred I/O sorts all dirty pages by default, which incurs a
significant overhead. Make the sorting step optional and update the few
drivers that require it. Use a FIFO list by default.
Most fbdev drivers with deferred I/O build a bounding rectangle around
the dirty pages or simply flush the whole screen. The only two affected
DRM drivers, generic fbdev and vmwgfx, both use a bounding rectangle.
In those cases, the exact order of the pages doesn't matter. The other
drivers look at the page index or handle pages one-by-one. The patch
sets the sort_pagelist flag for those, even though some of them would
probably work correctly without sorting. Driver maintainers should update
their driver accordingly.
Sorting pages by memory offset for deferred I/O performs an implicit
bubble-sort step on the list of dirty pages. The algorithm goes through
the list of dirty pages and inserts each new page according to its
index field. Even worse, list traversal always starts at the first
entry. As video memory is most likely updated scanline by scanline, the
algorithm traverses through the complete list for each updated page.
For example, with 1024x768x32bpp each page covers exactly one scanline.
Writing a single screen update from top to bottom requires updating
768 pages. With an average list length of 384 entries, a screen update
creates (768 * 384 =) 294912 compare operation.
Fix this by making the sorting step opt-in and update the few drivers
that require it. All other drivers work with unsorted page lists. Pages
are appended to the list. Therefore, in the common case of writing the
framebuffer top to bottom, pages are still sorted by offset, which may
have a positive effect on performance.
Playing a video [1] in mplayer's benchmark mode shows the difference
(i7-4790, FullHD, simpledrm, kernel with debugging).
VC shows the overhead of video decoding, VO shows the overhead of the
video output. Using unsorted page lists reduces the benchmark's run time
by ~32s/~25%.
v2:
* Make sorted pagelists the special case (Sam)
* Comment on drivers' use of pagelist (Sam)
* Warn about the overhead in comment
Return early if a page is already in the list of dirty pages for
deferred I/O. This can be detected if the page's list head is not
empty. Keep the list head initialized while the page is not enlisted
to make this work reliably.
The UART supports an auto-RTS mode in which the RTS pin is automatically
activated during transmission. So mark this mode as being supported even
if RTS is not controlled by the driver but the UART.
Also the serial core expects now at least one of both modes rts-on-send or
rts-after-send to be supported. This is since during sanitization
unsupported flags are deleted from a RS485 configuration set by userspace.
However if the configuration ends up with both flags unset, the core prints
a warning since it considers such a configuration invalid (see
uart_sanitize_serial_rs485()).
There is a scenario where DWC3 runtime suspend is blocked due to the
dwc->connected flag still being true while PM usage_count is zero after
DWC3 giveback is completed and the USB gadget session is being terminated.
This leads to a case where nothing schedules a PM runtime idle for the
device.
The exact condition is seen with the following sequence:
1. USB bus reset is issued by the host
2. Shortly after, or concurrently, a USB PD DR SWAP request is received
(sink->source)
3. USB bus reset event handler runs and issues
dwc3_stop_active_transfers(), and pending transfer are stopped
4. DWC3 usage_count decremented to 0, and runtime idle occurs while
dwc->connected == true, returns -EBUSY
5. DWC3 disconnect event seen, dwc->connected set to false due to DR
swap handling
6. No runtime idle after this point
Address this by issuing an asynchronous PM runtime idle call after the
disconnect event is completed, as it modifies the dwc->connected flag,
which is what blocks the initial runtime idle.
Current EP0 dequeue path will share the same as other EPs. However, there
are some special considerations that need to be made for EP0 transfers:
- EP0 transfers never transition into the started_list
- EP0 only has one active request at a time
In case there is a vendor specific control message for a function over USB
FFS, then there is no guarantee on the timeline which the DATA/STATUS stage
is responded to. While this occurs, any attempt to end transfers on
non-control EPs will end up having the DWC3_EP_DELAY_STOP flag set, and
defer issuing of the end transfer command. If the USB FFS application
decides to timeout the control transfer, or if USB FFS AIO path exits, the
USB FFS driver will issue a call to usb_ep_dequeue() for the ep0 request.
In case of the AIO exit path, the AIO FS blocks until all pending USB
requests utilizing the AIO path is completed. However, since the dequeue
of ep0 req does not happen properly, all non-control EPs with the
DWC3_EP_DELAY_STOP flag set will not be handled, and the AIO exit path will
be stuck waiting for the USB FFS data endpoints to receive a completion
callback.
Fix is to utilize dwc3_ep0_reset_state() in the dequeue API to ensure EP0
is brought back to the SETUP state, and ensures that any deferred end
transfer commands are handled. This also will end any active transfers
on EP0, compared to the previous implementation which directly called
giveback only.
Several sequences utilize the same routine for forcing the control endpoint
back into the SETUP phase. This is required, because those operations need
to ensure that EP0 is back in the default state.
It was observed that there are hosts that may complete pending SETUP
transactions before the stop active transfers and controller halt occurs,
leading to lingering endxfer commands on DEPs on subsequent pullup/gadget
start iterations.
The sequence shows that the USB gadget disconnect (dwc3_gadget_pullup(0))
routine completed successfully, allowing for the USB gadget to proceed with
a USB gadget connect. However, if this occurs the system runs into an
issue where:
BUG: spinlock already unlocked on CPU
spin_bug+0x0
dwc3_remove_requests+0x278
dwc3_ep0_out_start+0xb0
__dwc3_gadget_start+0x25c
This is due to the pending endxfers, leading to gadget start (w/o lock
held) to execute the remove requests, which will unlock the dwc3
spinlock as part of giveback.
To mitigate this, resolve the pending endxfers on the pullup disable
path by re-locating the SETUP phase check after stop active transfers, since
that is where the DWC3_EP_DELAY_STOP is potentially set. This also allows
for handling of a host that may be unresponsive by using the completion
timeout to trigger the stall and restart for EP0.
During a cable disconnect sequence, if ep0state is not in the SETUP phase,
then nothing will trigger any pending end transfer commands. Force
stopping of any pending SETUP transaction, and move back to the SETUP
phase.
If any function drivers request for a delayed status phase, this leads to a
SETUP transfer timeout error, since the function may take longer to process
the DATA stage. This eventually results in end transfer timeouts, as there
is a pending SETUP transaction.
In addition, allow the DWC3_EP_DELAY_STOP to be set for if there is a
delayed status requested. Ocasionally, a host may abort the current SETUP
transaction, by issuing a subsequent SETUP token. In those situations, it
would result in an endxfer timeout as well.
According to the databook ep0 should be in setup phase during reset.
If host issues reset between control transfers, ep0 will be in an
invalid state. Fix this by issuing stall and restart on ep0 if it
is not in setup phase.
Also SW needs to complete pending control transfer and setup core for
next setup stage as per data book. Hence check ep0 state during reset
interrupt handling and make sure active transfers on ep0 out/in
endpoint are stopped by queuing ENDXFER command for that endpoint and
restart ep0 out again to receive next setup packet.
If the controller hasn't DMA'ed the Setup data from its fifo, it won't
process the End Transfer command. Polling for the command completion may
block the driver from servicing the Setup phase and cause a timeout.
Previously we only check and delay issuing End Transfer in the case of
endpoint dequeue. Let's do that for all End Transfer scenarios.
The driver shouldn't be able to issue End Transfer to the control
endpoint at anytime. Typically we should only do so in error cases such
as invalid/unexpected direction of Data Phase as described in the
control transfer flow of the programming guide. It _may_ end started
data phase during controller deinitialization from soft disconnect or
driver removal. However, that should not happen because the driver
should be maintained in EP0_SETUP_PHASE during driver tear-down. On
soft-connect, the controller should be reset from a soft-reset and there
should be no issue starting the control endpoint.
Since we can't guarantee that the host won't send new Setup packet
before going through the device-initiated disconnect, don't prepare
beyond the Setup stage and keep the device in EP0_SETUP_PHASE. This
ensures that the device-initated disconnect sequence can go through
gracefully. Note that the controller won't service the End Transfer
command if it can't DMA out the Setup packet.
If a Setup packet is received but yet to DMA out, the controller will
not process the End Transfer command of any endpoint. Polling of its
DEPCMD.CmdAct may block setting up TRB for Setup packet, causing a
command timeout.
This may occur if the driver doesn’t service the completion interrupt of
the control status stage yet due to system latency, then it won’t
prepare TRB and start the transfer for the next Setup Stage. To the host
side, the control transfer had completed, and the host can send a new
Setup packet at this point.
In the meanwhile, if the driver receives an async call to dequeue a
request (triggering End Transfer) to any endpoint, then the driver will
service that End transfer first, blocking the control status stage
completion handler. Since no TRB is available for the Setup stage, the
Setup packet can’t be DMA’ed out and the End Transfer gets hung.
The driver must not block setting up of the Setup stage. So track and
only issue the End Transfer command only when there’s Setup TRB prepared
so that the controller can DMA out the Setup packet. Delay the End
transfer command if there's no Setup TRB available. This is applicable to
all DWC_usb3x IPs.
When the mpi_ec_ctx structure is initialized, some fields are not
cleared, causing a crash when referencing the field when the
structure was released. Initially, this issue was ignored because
memory for mpi_ec_ctx is allocated with the __GFP_ZERO flag.
For example, this error will be triggered when calculating the
Za value for SM2 separately.
When a fence signals there is a very small race window where the timestamp
isn't updated yet. sync_file solves this by busy waiting for the
timestamp to appear, but on other ocassions didn't handled this
correctly.
Provide a dma_fence_timestamp() helper function for this and use it in
all appropriate cases.
Another alternative would be to grab the spinlock when that happens.
v2 by teddy: add a wait parameter to wait for the timestamp to show up, in case
the accurate timestamp is needed and/or the timestamp is not based on
ktime (e.g. hw timestamp)
v3 chk: drop the parameter again for unified handling
Signed-off-by: Yunxiang Li <Yunxiang.Li@amd.com> Signed-off-by: Christian König <christian.koenig@amd.com> Fixes: 1774baa64f93 ("drm/scheduler: Change scheduled fence track v2") Reviewed-by: Alex Deucher <alexander.deucher@amd.com> CC: stable@vger.kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20230929104725.2358-1-christian.koenig@amd.com Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot reported a task hung; at the same time, GC was looping infinitely
in list_for_each_entry_safe() for OOB skb. [0]
syzbot demonstrated that the list_for_each_entry_safe() was not actually
safe in this case.
A single skb could have references for multiple sockets. If we free such
a skb in the list_for_each_entry_safe(), the current and next sockets could
be unlinked in a single iteration.
unix_notinflight() uses list_del_init() to unlink the socket, so the
prefetched next socket forms a loop itself and list_for_each_entry_safe()
never stops.
Here, we must use while() and make sure we always fetch the first socket.
Where that s->saved_cmdlines allocation looks to be a dangling allocation
to kmemleak. That's because kmemleak only keeps track of kmalloc()
allocations. For allocations that use page_alloc() directly, the kmemleak
needs to be explicitly informed about it.
Add kmemleak_alloc() and kmemleak_free() around the page allocation so
that it doesn't give the following false positive:
The unused clock cleanup uses the _sync initcall to give all users at
earlier initcalls time to probe. Do the same to avoid leaving some PDs
dangling at "on" (which actually happened on qcom!).
Lock jsk->sk to prevent UAF when setsockopt(..., SO_J1939_FILTER, ...)
modifies jsk->filters while receiving packets.
Following trace was seen on affected system:
==================================================================
BUG: KASAN: slab-use-after-free in j1939_sk_recv_match_one+0x1af/0x2d0 [can_j1939]
Read of size 4 at addr ffff888012144014 by task j1939/350
A reasonable fix is to change j1939_socks_lock to an rwlock, since in
the rare situations where a write lock is required for the linked list
that j1939_socks_lock is protecting, the code does not attempt to
acquire any more locks. This would break the circular lock dependency,
where, for example, the current thread already locks j1939_socks_lock
and attempts to acquire sk_session_queue_lock, and at the same time,
another thread attempts to acquire j1939_socks_lock while holding
sk_session_queue_lock.
NOTE: This patch along does not fix the unregister_netdevice bug
reported by Syzbot; instead, it solves a deadlock situation to prepare
for one or more further patches to actually fix the Syzbot bug, which
appears to be a reference counting problem within the j1939 codebase.
For shared memory of type SHM_HUGETLB, hugetlb pages are reserved in
shmget() call. If SHM_NORESERVE flags is specified then the hugetlb pages
are not reserved. However when the shared memory is attached with the
shmat() call the hugetlb pages are getting reserved incorrectly for
SHM_HUGETLB shared memory created with SHM_NORESERVE which is a bug.
-------------------------------
Following test shows the issue.
$cat shmhtb.c
int main()
{
int shmflags = 0660 | IPC_CREAT | SHM_HUGETLB | SHM_NORESERVE;
int shmid;
In fs/ceph/caps.c, in encode_cap_msg(), "use after free" error was
caught by KASAN at this line - 'ceph_buffer_get(arg->xattr_buf);'. This
implies before the refcount could be increment here, it was freed.
In same file, in "handle_cap_grant()" refcount is decremented by this
line - 'ceph_buffer_put(ci->i_xattrs.blob);'. It appears that a race
occurred and resource was freed by the latter line before the former
line could increment it.
encode_cap_msg() is called by __send_cap() and __send_cap() is called by
ceph_check_caps() after calling __prep_cap(). __prep_cap() is where
arg->xattr_buf is assigned to ci->i_xattrs.blob. This is the spot where
the refcount must be increased to prevent "use after free" error.
Cc: stable@vger.kernel.org Link: https://tracker.ceph.com/issues/59259 Signed-off-by: Rishabh Dave <ridave@redhat.com> Reviewed-by: Jeff Layton <jlayton@kernel.org> Reviewed-by: Xiubo Li <xiubli@redhat.com> Signed-off-by: Ilya Dryomov <idryomov@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw_new resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004005c3fb800000001005c3fb80000000400000001
dfc0: 00000004005c3fb8b6f6bba000000004000000040059edb80000000000000000
dfe0: 00000004bed918f0b6f09bd3b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+ Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state") Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM") Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Symptom:
In case of a bad cable connection (e.g. dirty optics) a fast sequence of
network DOWN-UP-DOWN-UP could happen. UP triggers recovery of the qeth
interface. In case of a second DOWN while recovery is still ongoing, it
can happen that the IP@ of a Layer3 qeth interface is lost and will not
be recovered by the second UP.
Problem:
When registration of IP addresses with Layer 3 qeth devices fails, (e.g.
because of bad address format) the respective IP address is deleted from
its hash-table in the driver. If registration fails because of a ENETDOWN
condition, the address should stay in the hashtable, so a subsequent
recovery can restore it.
3caa4af834df ("qeth: keep ip-address after LAN_OFFLINE failure")
fixes this for registration failures during normal operation, but not
during recovery.
Solution:
Keep L3-IP address in case of ENETDOWN in qeth_l3_recover_ip(). For
consistency with qeth_l3_add_ip() we also keep it in case of EADDRINUSE,
i.e. for some reason the card already/still has this address registered.
Fixes: 4a71df50047f ("qeth: new qeth device driver") Cc: stable@vger.kernel.org Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Link: https://lore.kernel.org/r/20240206085849.2902775-1-wintera@linux.ibm.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The below commit introduced a WARN when phy state is not in the states:
PHY_HALTED, PHY_READY and PHY_UP.
commit 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state")
When cpsw resumes, there have port in PHY_NOLINK state, so the below
warning comes out. Set mac_managed_pm be true to tell mdio that the phy
resume/suspend is managed by the mac, to fix the following warning:
WARNING: CPU: 0 PID: 965 at drivers/net/phy/phy_device.c:326 mdio_bus_phy_resume+0x140/0x144
CPU: 0 PID: 965 Comm: sh Tainted: G O 6.1.46-g247b2535b2 #1
Hardware name: Generic AM33XX (Flattened Device Tree)
unwind_backtrace from show_stack+0x18/0x1c
show_stack from dump_stack_lvl+0x24/0x2c
dump_stack_lvl from __warn+0x84/0x15c
__warn from warn_slowpath_fmt+0x1a8/0x1c8
warn_slowpath_fmt from mdio_bus_phy_resume+0x140/0x144
mdio_bus_phy_resume from dpm_run_callback+0x3c/0x140
dpm_run_callback from device_resume+0xb8/0x2b8
device_resume from dpm_resume+0x144/0x314
dpm_resume from dpm_resume_end+0x14/0x20
dpm_resume_end from suspend_devices_and_enter+0xd0/0x924
suspend_devices_and_enter from pm_suspend+0x2e0/0x33c
pm_suspend from state_store+0x74/0xd0
state_store from kernfs_fop_write_iter+0x104/0x1ec
kernfs_fop_write_iter from vfs_write+0x1b8/0x358
vfs_write from ksys_write+0x78/0xf8
ksys_write from ret_fast_syscall+0x0/0x54
Exception stack(0xe094dfa8 to 0xe094dff0)
dfa0: 00000004005c3fb800000001005c3fb80000000400000001
dfc0: 00000004005c3fb8b6f6bba000000004000000040059edb80000000000000000
dfe0: 00000004bed918f0b6f09bd3b6e89a66
Cc: <stable@vger.kernel.org> # v6.0+ Fixes: 744d23c71af3 ("net: phy: Warn about incorrect mdio_bus_phy_resume() state") Fixes: fba863b81604 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM") Signed-off-by: Sinthu Raja <sinthu.raja@ti.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When updating the affinity of a VPE, the VMOVP command is currently skipped
if the two CPUs are part of the same VPE affinity.
But this is wrong, as the doorbell corresponding to this VPE is still
delivered on the 'old' CPU, which screws up the balancing. Furthermore,
offlining that 'old' CPU results in doorbell interrupts generated for this
VPE being discarded.
The harsh reality is that VMOVP cannot be elided when a set_affinity()
request occurs. It needs to be obeyed, and if an optimisation is to be
made, it is at the point where the affinity change request is made (such as
in KVM).
Drop the VMOVP elision altogether, and only use the vpe_table_mask
to try and stay within the same ITS affinity group if at all possible.
Fixes: dd3f050a216e (irqchip/gic-v4.1: Implement the v4.1 flavour of VMOVP) Reported-by: Kunkun Jiang <jiangkunkun@huawei.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240213101206.2137483-4-maz@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was observed on Broadcom devices that use GIC v3 architecture L1
interrupt controllers as the parent of brcmstb-l2 interrupt controllers
that the deactivation of the parent interrupt could happen before the
brcmstb-l2 deasserted its output. This would lead the GIC to reactivate the
interrupt only to find that no L2 interrupt was pending. The result was a
spurious interrupt invoking handle_bad_irq() with its associated
messaging. While this did not create a functional problem it is a waste of
cycles.
The hazard exists because the memory mapped bus writes to the brcmstb-l2
registers are buffered and the GIC v3 architecture uses a very efficient
system register write to deactivate the interrupt.
Add a write memory barrier prior to invoking chained_irq_exit() to
introduce a dsb(st) on those systems to ensure the system register write
cannot be executed until the memory mapped writes are visible to the
system.
[ florian: Added Fixes tag ]
Fixes: 7f646e92766e ("irqchip: brcmstb-l2: Add Broadcom Set Top Box Level-2 interrupt controller") Signed-off-by: Doug Berger <opendmb@gmail.com> Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> Acked-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20240210012449.3009125-1-florian.fainelli@broadcom.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pointer can change here since the SKB can change, so we
actually later open-coded IEEE80211_SKB_CB() again. Reload
the pointer where needed, so the monitor-mode case using it
gets fixed, and then use info-> later as well.
When physical ports are reset (either through link failure or manually
toggled down and up again) that are slaved to a Linux bond with a tunnel
endpoint IP address on the bond device, not all tunnel packets arriving
on the bond port are decapped as expected.
The bond dev assigns the same MAC address to itself and each of its
slaves. When toggling a slave device, the same MAC address is therefore
offloaded to the NFP multiple times with different indexes.
The issue only occurs when re-adding the shared mac. The
nfp_tunnel_add_shared_mac() function has a conditional check early on
that checks if a mac entry already exists and if that mac entry is
global: (entry && nfp_tunnel_is_mac_idx_global(entry->index)). In the
case of a bonded device (For example br-ex), the mac index is obtained,
and no new index is assigned.
We therefore modify the conditional in nfp_tunnel_add_shared_mac() to
check if the port belongs to the LAG along with the existing checks to
prevent a new global mac index from being re-assigned to the slave port.
Fixes: 20cce8865098 ("nfp: flower: enable MAC address sharing for offloadable devs") CC: stable@vger.kernel.org # 5.1+ Signed-off-by: Daniel de Villiers <daniel.devilliers@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 1st and 2nd expansion BAR configuration registers are configured,
when the driver starts up, in variables 'barcfg_msix_general' and
'barcfg_msix_xpb', respectively. The 'LengthSelect' field is ORed in
from bit 0, which is incorrect. The 'LengthSelect' field should
start from bit 27.
This has largely gone un-noticed because
NFP_PCIE_BAR_PCIE2CPP_LengthSelect_32BIT happens to be 0.
Fixes: 4cb584e0ee7d ("nfp: add CPP access core") Cc: stable@vger.kernel.org # 4.11+ Signed-off-by: Daniel Basilio <daniel.basilio@corigine.com> Signed-off-by: Louis Peens <louis.peens@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 1b05ece0c931 ("crypto: ccp - During shutdown, check SEV data pointer before using") Cc: stable@vger.kernel.org Reviewed-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Kim Phillips <kim.phillips@amd.com> Reviewed-by: Liam Merwick <liam.merwick@oracle.com> Acked-by: John Allen <john.allen@amd.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzbot reported a hang issue in migrate_pages_batch() called by mbind()
and nilfs_lookup_dirty_data_buffers() called in the log writer of nilfs2.
While migrate_pages_batch() locks a folio and waits for the writeback to
complete, the log writer thread that should bring the writeback to
completion picks up the folio being written back in
nilfs_lookup_dirty_data_buffers() that it calls for subsequent log
creation and was trying to lock the folio. Thus causing a deadlock.
In the first place, it is unexpected that folios/pages in the middle of
writeback will be updated and become dirty. Nilfs2 adds a checksum to
verify the validity of the log being written and uses it for recovery at
mount, so data changes during writeback are suppressed. Since this is
broken, an unclean shutdown could potentially cause recovery to fail.
Investigation revealed that the root cause is that the wait for writeback
completion in nilfs_page_mkwrite() is conditional, and if the backing
device does not require stable writes, data may be modified without
waiting.
Fix these issues by making nilfs_page_mkwrite() wait for writeback to
finish regardless of the stable write requirement of the backing device.
Link: https://lkml.kernel.org/r/20240131145657.4209-1-konishi.ryusuke@gmail.com Fixes: 1d1d1a767206 ("mm: only enforce stable page writes if the backing device requires it") Signed-off-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Reported-by: syzbot+ee2ae68da3b22d04cd8d@syzkaller.appspotmail.com Closes: https://lkml.kernel.org/r/00000000000047d819061004ad6c@google.com Tested-by: Ryusuke Konishi <konishi.ryusuke@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helper function nilfs_recovery_copy_block() of
nilfs_recovery_dsync_blocks(), which recovers data from logs created by
data sync writes during a mount after an unclean shutdown, incorrectly
calculates the on-page offset when copying repair data to the file's page
cache. In environments where the block size is smaller than the page
size, this flaw can cause data corruption and leak uninitialized memory
bytes during the recovery process.
Fix these issues by correcting this byte offset calculation on the page.
This change uses the appropriate _cansleep or non-sleeping API for
reading GPIO read-only state. This allows users with GPIOs that
never sleepbeing called in atomic context.
Implement the same mechanism as in commit 52af318c93e97 ("mmc: Allow
non-sleeping GPIO cd").
When ident_pud_init() uses only gbpages to create identity maps, large
ranges of addresses not actually requested can be included in the
resulting table; a 4K request will map a full GB. On UV systems, this
ends up including regions that will cause hardware to halt the system
if accessed (these are marked "reserved" by BIOS). Even processor
speculation into these regions is enough to trigger the system halt.
Only use gbpages when map creation requests include the full GB page
of space. Fall back to using smaller 2M pages when only portions of a
GB page are included in the request.
No attempt is made to coalesce mapping requests. If a request requires
a map entry at the 2M (pmd) level, subsequent mapping requests within
the same 1G region will also be at the pmd level, even if adjacent or
overlapping such requests could have been combined to map a full
gbpage. Existing usage starts with larger regions and then adds
smaller regions, so this should not have any great consequence.
[ dhansen: fix up comment formatting, simplifty changelog ]
The kernel built with MCRUSOE is unbootable on Transmeta Crusoe. It shows
the following error message:
This kernel requires an i686 CPU, but only detected an i586 CPU.
Unable to boot - please use a kernel appropriate for your CPU.
Remove MCRUSOE from the condition introduced in commit in Fixes, effectively
changing X86_MINIMUM_CPU_FAMILY back to 5 on that machine, which matches the
CPU family given by CPUID.
[ bp: Massage commit message. ]
Fixes: 25d76ac88821 ("x86/Kconfig: Explicitly enumerate i686-class CPUs in Kconfig") Signed-off-by: Aleksander Mazur <deweloper@wp.pl> Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de> Acked-by: H. Peter Anvin <hpa@zytor.com> Cc: <stable@kernel.org> Link: https://lore.kernel.org/r/20240123134309.1117782-1-deweloper@wp.pl Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nysal reported that userspace backtraces are missing in offcputime bcc
tool. As an example:
$ sudo ./bcc/tools/offcputime.py -uU
Tracing off-CPU time (us) of user threads by user stack... Hit Ctrl-C to end.
The offcputime bcc tool attaches a bpf program to a kprobe on
finish_task_switch(), which is usually hit on a syscall from userspace.
With the switch to system call vectored, we started setting
pt_regs->link to zero. This is because system call vectored behaves like
a function call with LR pointing to the system call return address, and
with no modification to SRR0/SRR1. The LR value does indicate our next
instruction, so it is being saved as pt_regs->nip, and pt_regs->link is
being set to zero. This is not a problem by itself, but BPF uses perf
callchain infrastructure for capturing stack traces, and that stores LR
as the second entry in the stack trace. perf has code to cope with the
second entry being zero, and skips over it. However, generic userspace
unwinders assume that a zero entry indicates end of the stack trace,
resulting in a truncated userspace stack trace.
Rather than fixing all userspace unwinders to ignore/skip past the
second entry, store the real LR value in pt_regs->link so that there
continues to be a valid, though duplicate entry in the stack trace.
With this change:
$ sudo ./bcc/tools/offcputime.py -uU
Tracing off-CPU time (us) of user threads by user stack... Hit Ctrl-C to end.
Some people are seeing a warning similar to this when using a crystal:
max310x 11-006c: clock is not stable yet
The datasheet doesn't mention the maximum time to wait for the clock to be
stable when using a crystal, and it seems that the 10ms delay in the driver
is not always sufficient.
Jan Kundrát reported that it took three tries (each separated by 10ms) to
get a stable clock.
Modify behavior to check stable clock ready bit multiple times (20), and
waiting 10ms between each try.
Note: the first draft of the driver originally used a 50ms delay, without
checking the clock stable bit.
Then a loop with 1000 retries was implemented, each time reading the clock
stable bit.
The return type for ring_buffer_poll_wait() is __poll_t. This is behind
the scenes an unsigned where we can set event bits. In case of a
non-allocated CPU, we do return instead -EINVAL (0xffffffea). Lucky us,
this ends up setting few error bits (EPOLLERR | EPOLLHUP | EPOLLNVAL), so
user-space at least is aware something went wrong.
Nonetheless, this is an incorrect code. Replace that -EINVAL with a
proper EPOLLERR to clean that output. As this doesn't change the
behaviour, there's no need to treat this change as a bug fix.
Link: https://lore.kernel.org/linux-trace-kernel/20240131140955.3322792-1-vdonnefort@google.com Cc: stable@vger.kernel.org Fixes: 6721cb6002262 ("ring-buffer: Do not poll non allocated cpu buffers") Signed-off-by: Vincent Donnefort <vdonnefort@google.com> Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit ac5047671758 ("hv_netvsc: Disable NAPI before closing the
VMBus channel"), napi_disable was getting called for all channels,
including all subchannels without confirming if they are enabled or not.
This caused hv_netvsc getting hung at napi_disable, when netvsc_probe()
has finished running but nvdev->subchan_work has not started yet.
netvsc_subchan_work() -> rndis_set_subchannel() has not created the
sub-channels and because of that netvsc_sc_open() is not running.
netvsc_remove() calls cancel_work_sync(&nvdev->subchan_work), for which
netvsc_subchan_work did not run.
netif_napi_add() sets the bit NAPI_STATE_SCHED because it ensures NAPI
cannot be scheduled. Then netvsc_sc_open() -> napi_enable will clear the
NAPIF_STATE_SCHED bit, so it can be scheduled. napi_disable() does the
opposite.
Now during netvsc_device_remove(), when napi_disable is called for those
subchannels, napi_disable gets stuck on infinite msleep.
This fix addresses this problem by ensuring that napi_disable() is not
getting called for non-enabled NAPI struct.
But netif_napi_del() is still necessary for these non-enabled NAPI struct
for cleanup purpose.
Without unsigned long typecast, the size is passed in as zero if page
array size >= 4GB, nr_pages >= 0x100000, then sg list converted will
have the first and the last chunk lost.
Signed-off-by: Philip Yang <Philip.Yang@amd.com> Acked-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> CC: stable@vger.kernel.org Signed-off-by: Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20230821200201.24685-1-Philip.Yang@amd.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel fails when compiling without `CONFIG_REGMAP_I2C` but with
`CONFIG_BMA400`.
```
ld: drivers/iio/accel/bma400_i2c.o: in function `bma400_i2c_probe':
bma400_i2c.c:(.text+0x23): undefined reference to `__devm_regmap_init_i2c'
```
Recently, we encounter kernel crash in function rm3100_common_probe
caused by out of bound access of array rm3100_samp_rates (because of
underlying hardware failures). Add boundary check to prevent out of
bound access.
Fixes: 121354b2eceb ("iio: magnetometer: Add driver support for PNI RM3100") Suggested-by: Zhouyi Zhou <zhouzhouyi@gmail.com> Signed-off-by: zhili.liu <zhili.liu@ucas.com.cn> Link: https://lore.kernel.org/r/1704157631-3814-1-git-send-email-zhouzhouyi@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4c3577db3e4f ("Staging: iio: impedance-analyzer: Fix sparse
warning") fixed a compiler warning, but introduced a bug that resulted
in one of the two 16 bit IIO channels always being zero (when both are
enabled).
This is because int is 32 bits wide on most architectures and in the
case of a little-endian machine the two most significant bytes would
occupy the buffer for the second channel as 'val' is being passed as a
void pointer to 'iio_push_to_buffers()'.
Fix by defining 'val' as u16. Tested working on ARM64.
While looking at improving the saved_cmdlines cache I found a huge amount
of wasted memory that should be used for the cmdlines.
The tracing data saves pids during the trace. At sched switch, if a trace
occurred, it will save the comm of the task that did the trace. This is
saved in a "cache" that maps pids to comms and exposed to user space via
the /sys/kernel/tracing/saved_cmdlines file. Currently it only caches by
default 128 comms.
The structure that uses this creates an array to store the pids using
PID_MAX_DEFAULT (which is usually set to 32768). This causes the structure
to be of the size of 131104 bytes on 64 bit machines.
In hex: 131104 = 0x20020, and since the kernel allocates generic memory in
powers of two, the kernel would allocate 0x40000 or 262144 bytes to store
this structure. That leaves 131040 bytes of wasted space.
Worse, the structure points to an allocated array to store the comm names,
which is 16 bytes times the amount of names to save (currently 128), which
is 2048 bytes. Instead of allocating a separate array, make the structure
end with a variable length string and use the extra space for that.
This is similar to a recommendation that Linus had made about eventfs_inode names:
Instead of allocating a separate string array to hold the saved comms,
have the structure end with: char saved_cmdlines[]; and round up to the
next power of two over sizeof(struct saved_cmdline_buffers) + num_cmdlines * TASK_COMM_LEN
It will use this extra space for the saved_cmdline portion.
Now, instead of saving only 128 comms by default, by using this wasted
space at the end of the structure it can save over 8000 comms and even
saves space by removing the need for allocating the other array.
Link: https://lore.kernel.org/linux-trace-kernel/20240209063622.1f7b6d5f@rorschach.local.home Cc: stable@vger.kernel.org Cc: Masami Hiramatsu <mhiramat@kernel.org> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Cc: Vincent Donnefort <vdonnefort@google.com> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Mete Durlu <meted@linux.ibm.com> Fixes: 939c7a4f04fcd ("tracing: Introduce saved_cmdlines_size file") Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ext4_move_extents(), moved_len is only updated when all moves are
successfully executed, and only discards orig_inode and donor_inode
preallocations when moved_len is not zero. When the loop fails to exit
after successfully moving some extents, moved_len is not updated and
remains at 0, so it does not discard the preallocations.
If the moved extents overlap with the preallocated extents, the
overlapped extents are freed twice in ext4_mb_release_inode_pa() and
ext4_process_freed_data() (as described in commit 94d7c16cbbbd ("ext4:
Fix double-free of blocks with EXT4_IOC_MOVE_EXT")), and bb_free is
incremented twice. Hence when trim is executed, a zero-division bug is
triggered in mb_update_avg_fragment_size() because bb_free is not zero
and bb_fragments is zero.
Therefore, update move_len after each extent move to avoid the issue.
Reported-by: Wei Chen <harperchen1110@gmail.com> Reported-by: xingwei lee <xrivendell7@gmail.com> Closes: https://lore.kernel.org/r/CAO4mrferzqBUnCag8R3m2zf897ts9UEuhjFQGPtODT92rYyR2Q@mail.gmail.com Fixes: fcf6b1b729bc ("ext4: refactor ext4_move_extents code base") CC: <stable@vger.kernel.org> # 3.18 Signed-off-by: Baokun Li <libaokun1@huawei.com> Reviewed-by: Jan Kara <jack@suse.cz> Link: https://lore.kernel.org/r/20240104142040.2835097-2-libaokun1@huawei.com Signed-off-by: Theodore Ts'o <tytso@mit.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In remoteproc shutdown sequence, rpmsg_remove will get called which
would depopulate all the child nodes that have been created during
rpmsg_probe. This would result in cb_remove call for all the context
banks for the remoteproc. In cb_remove function, session 0 is
getting skipped which is not correct as session 0 will never become
available again. Add changes to mark session 0 also as invalid.
In (e)poll mode, threads often depend on I/O events to determine when
data is ready for consumption. Within binder, a thread may initiate a
command via BINDER_WRITE_READ without a read buffer and then make use
of epoll_wait() or similar to consume any responses afterwards.
It is then crucial that epoll threads are signaled via wakeup when they
queue their own work. Otherwise, they risk waiting indefinitely for an
event leaving their work unhandled. What is worse, subsequent commands
won't trigger a wakeup either as the thread has pending work.
Customer has reported an issue with specific desktop platform
where two CS42L42 codecs are connected to CS8409 HDA bridge.
If "Master Volume Control" is created then on Ubuntu OS UCM
left/right balance slider in UI audio settings has no effect.
This patch will fix this issue for a target paltform.
WCD938x sound codec driver ignores return status of getting regulators
and returns EINVAL instead of EPROBE_DEFER. If regulator provider
probes after the codec, system is left without probed audio:
wcd938x_codec audio-codec: wcd938x_probe: Fail to obtain platform data
wcd938x_codec: probe of audio-codec failed with error -22
Fixes: 16572522aece ("ASoC: codecs: wcd938x-sdw: add SoundWire driver") Cc: <stable@vger.kernel.org> Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://msgid.link/r/20240117151208.1219755-1-krzysztof.kozlowski@linaro.org Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Invoking the make_tx_response() / push_tx_responses() pair with no lock
held would be acceptable only if all such invocations happened from the
same context (NAPI instance or dealloc thread). Since this isn't the
case, and since the interface "spec" also doesn't demand that multicast
operations may only be performed with no in-flight transmits,
MCAST_{ADD,DEL} processing also needs to acquire the response lock
around the invocations.
To prevent similar mistakes going forward, "downgrade" the present
functions to private helpers of just the two remaining ones using them
directly, with no forward declarations anymore. This involves renaming
what so far was make_tx_response(), for the new function of that name
to serve the new (wrapper) purpose.
While there,
- constify the txp parameters,
- correct xenvif_idx_release()'s status parameter's type,
- rename {,_}make_tx_response()'s status parameters for consistency with
xenvif_idx_release()'s.
Fixes: 210c34dcd8d9 ("xen-netback: add support for multicast control") Cc: stable@vger.kernel.org Signed-off-by: Jan Beulich <jbeulich@suse.com> Reviewed-by: Paul Durrant <paul@xen.org> Link: https://lore.kernel.org/r/980c6c3d-e10e-4459-8565-e8fbde122f00@suse.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Syzkaller reported [1] hitting a warning after failing to allocate
resources for skb in hsr_init_skb(). Since a WARN_ONCE() call will
not help much in this case, it might be prudent to switch to
netdev_warn_once(). At the very least it will suppress syzkaller
reports such as [1].
Just in case, use netdev_warn_once() in send_prp_supervision_frame()
for similar reasons.
rx_data_reassembly skb is stored during NCI data exchange for processing
fragmented packets. It is dropped only when the last fragment is processed
or when an NTF packet with NCI_OP_RF_DEACTIVATE_NTF opcode is received.
However, the NCI device may be deallocated before that which leads to skb
leak.
As by design the rx_data_reassembly skb is bound to the NCI device and
nothing prevents the device to be freed before the skb is processed in
some way and cleaned, free it on the NCI device cleanup.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 6a2968aaf50c ("NFC: basic NCI protocol implementation") Cc: stable@vger.kernel.org Reported-by: syzbot+6b7c68d9c21e4ee4251b@syzkaller.appspotmail.com Closes: https://lore.kernel.org/lkml/000000000000f43987060043da7b@google.com/ Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 90ceddcb4950 ("bpf: Support llvm-objcopy for vmlinux BTF")
changed the ELF type of .btf.vmlinux.bin.o to ET_REL via dd, which works
fine for little endian platforms:
While in the area, update the comment to mention that binutils 2.35+
matches LLD's behavior of rejecting an ET_EXEC input, which occurred
after the comment was added.
Cc: stable@vger.kernel.org Fixes: 90ceddcb4950 ("bpf: Support llvm-objcopy for vmlinux BTF") Link: https://github.com/llvm/llvm-project/pull/75643 Suggested-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Nathan Chancellor <nathan@kernel.org> Reviewed-by: Fangrui Song <maskray@google.com> Reviewed-by: Nicolas Schier <nicolas@fjasle.eu> Reviewed-by: Kees Cook <keescook@chromium.org> Reviewed-by: Justin Stitt <justinstitt@google.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
[nathan: Fix silent conflict due to lack of 7d153696e5db in older trees] Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The inode_getsecctx LSM hook has previously been corrected to have
-EOPNOTSUPP instead of 0 as the default return value to fix BPF LSM
behavior. However, the call_int_hook()-generated loop in
security_inode_getsecctx() was left treating 0 as the neutral value, so
after an LSM returns 0, the loop continues to try other LSMs, and if one
of them returns a non-zero value, the function immediately returns with
said value. So in a situation where SELinux and the BPF LSMs registered
this hook, -EOPNOTSUPP would be incorrectly returned whenever SELinux
returned 0.
Fix this by open-coding the call_int_hook() loop and making it use the
correct LSM_RET_DEFAULT() value as the neutral one, similar to what
other hooks do.
commit ab4750332dbe ("drm/amdgpu/sdma5.2: add begin/end_use ring
callbacks") caused GFXOFF control to be used more heavily and the
codepath that was removed from commit 0dee72639533 ("drm/amd: flush any
delayed gfxoff on suspend entry") now can be exercised at suspend again.
Users report that by using GNOME to suspend the lockscreen trigger will
cause SDMA traffic and the system can deadlock.
When the MPTCP PM detects that a subflow is stale, all the packet
scheduler must re-inject all the mptcp-level unacked data. To avoid
acquiring unneeded locks, it first try to check if any unacked data
is present at all in the RTX queue, but such check is currently
broken, as it uses TCP-specific helper on an MPTCP socket.
Funnily enough fuzzers and static checkers are happy, as the accessed
memory still belongs to the mptcp_sock struct, and even from a
functional perspective the recovery completed successfully, as
the short-cut test always failed.
A recent unrelated TCP change - commit d5fed5addb2b ("tcp: reorganize
tcp_sock fast path variables") - exposed the issue, as the tcp field
reorganization makes the mptcp code always skip the re-inection.
Fix the issue dropping the bogus call: we are on a slow path, the early
optimization proved once again to be evil.
Fixes: 1e1d9d6f119c ("mptcp: handle pending data on closed subflow") Cc: stable@vger.kernel.org Closes: https://github.com/multipath-tcp/mptcp_net-next/issues/468 Signed-off-by: Paolo Abeni <pabeni@redhat.com> Reviewed-by: Mat Martineau <martineau@kernel.org> Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org> Link: https://lore.kernel.org/r/20240131-upstream-net-20240131-mptcp-ci-issues-v1-1-4c1c11e571ff@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
get_line() does not trim the leading spaces, but the
parse_source_files() expects to get lines with source files paths where
the first space occurs after the file path.
Fixes: 70f30cfe5b89 ("modpost: use read_text_file() and get_line() for reading text files") Signed-off-by: Radek Krejci <radek.krejci@oracle.com> Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log