The function tipc_mon_rcv() allows a node to receive and process
domain_record structs from peer nodes to track their views of the
network topology.
This patch verifies that the number of members in a received domain
record does not exceed the limit defined by MAX_MON_DOMAIN, something
that may otherwise lead to a stack overflow.
tipc_mon_rcv() is called from the function tipc_link_proto_rcv(), where
we are reading a 32 bit message data length field into a uint16. To
avert any risk of bit overflow, we add an extra sanity check for this in
that function. We cannot see that happen with the current code, but
future designers being unaware of this risk, may introduce it by
allowing delivery of very large (> 64k) sk buffers from the bearer
layer. This potential problem was identified by Eric Dumazet.
This fixes CVE-2022-0435
Reported-by: Samuel Page <samuel.page@appgate.com> Reported-by: Eric Dumazet <edumazet@google.com> Fixes: 35c55c9877f8 ("tipc: add neighbor monitoring framework") Signed-off-by: Jon Maloy <jmaloy@redhat.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Samuel Page <samuel.page@appgate.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The soft dependency on cryptomgr is only needed in algapi because
if algapi isn't present then no algorithms can be loaded. This
also fixes the case where api is built-in but algapi is built as
a module as the soft dependency would otherwise get lost.
Fixes: 8ab23d547f65 ("crypto: api - Add softdep on cryptomgr") Reported-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Tested-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cifs client set 4 to DataLength of create_posix context, which mean
Mode variable of create_posix context is only available. So buffer
validation of ksmbd should check only the size of Mode except for
the size of Reserved variable.
Fixes: 8f77150c15f8 ("ksmbd: add buffer validation for SMB2_CREATE_CONTEXT") Cc: stable@vger.kernel.org # v5.15+ Reported-by: Steve French <smfrench@gmail.com> Tested-by: Steve French <stfrench@microsoft.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Steve French <stfrench@microsoft.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refuse SIDA memops on guests which are not protected.
For normal guests, the secure instruction data address designation,
which determines the location we access, is not under control of KVM.
Fixes: 19e122776886 (KVM: S390: protvirt: Introduce instruction data area bounce buffer) Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com> Cc: stable@vger.kernel.org Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was reported that the mmc host structure could be accessed after it
was freed in moxart_remove(), so fix this by saving the base register of
the device and using it instead of the pointer dereference.
Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Xiyu Yang <xiyuyang19@fudan.edu.cn> Cc: Xin Xiong <xiongx18@fudan.edu.cn> Cc: Xin Tan <tanxin.ctf@gmail.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Yang Li <yang.lee@linux.alibaba.com> Cc: linux-mmc@vger.kernel.org Cc: stable <stable@vger.kernel.org> Reported-by: whitehat002 <hackyzh002@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://lore.kernel.org/r/20220127071638.4057899-1-gregkh@linuxfoundation.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a test that sends large udp packet (which is fragmented)
via a stateless nft nat rule, i.e. 'ip saddr set 10.2.3.4'
and check that the datagram is received by peer.
On kernels without
commit 4e1860a38637 ("netfilter: nft_payload: do not update layer 4 checksum when mangling fragments")',
this will fail with:
cmp: EOF on /tmp/tmp.V1q0iXJyQF which is empty
-rw------- 1 root root 4096 Jan 24 22:03 /tmp/tmp.Aaqnq4rBKS
-rw------- 1 root root 0 Jan 24 22:03 /tmp/tmp.V1q0iXJyQF
ERROR: in and output file mismatch when checking udp with stateless nat
FAIL: nftables v1.0.0 (Fearless Fosdick #2)
On patched kernels, this will show:
PASS: IP statless for ns2-PFp89amx
The return from the call to platform_get_irq() is int, it can be
a negative error code, however this is being assigned to an unsigned
int variable 'irqn', so making 'irqn' an int.
Eliminate the following coccicheck warning:
./drivers/gpio/gpio-mpc8xxx.c:391:5-21: WARNING: Unsigned expression
compared with zero: mpc8xxx_gc -> irqn < 0
Reported-by: Abaci Robot <abaci@linux.alibaba.com> Fixes: 0b39536cc699 ("gpio: mpc8xxx: Fix IRQ check in mpc8xxx_probe") Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The return from the call to platform_get_irq() is int, it can be
a negative error code, however this is being assigned to an unsigned
int variable 'parent_irq', so making 'parent_irq' an int.
Eliminate the following coccicheck warning:
./drivers/gpio/gpio-idt3243x.c:167:6-16: WARNING: Unsigned expression
compared with zero: parent_irq < 0
Reported-by: Abaci Robot <abaci@linux.alibaba.com> Fixes: 30fee1d7462a ("gpio: idt3243x: Fix IRQ check in idt_gpio_probe") Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Which entails no changes in the tooling side as it doesn't introduce new
SNDRV_PCM_IOCTL_ ioctls.
To silence this perf tools build warning:
Warning: Kernel ABI header at 'tools/include/uapi/sound/asound.h' differs from latest version at 'include/uapi/sound/asound.h'
diff -u tools/include/uapi/sound/asound.h include/uapi/sound/asound.h
Cc: Dmitry Osipenko <digetx@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/lkml/Yf+6OT+2eMrYDEeX@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was found that a "suspicious RCU usage" lockdep warning was issued
with the rcu_read_lock() call in update_sibling_cpumasks(). It is
because the update_cpumasks_hier() function may sleep. So we have
to release the RCU lock, call update_cpumasks_hier() and reacquire
it afterward.
Also add a percpu_rwsem_assert_held() in update_sibling_cpumasks()
instead of stating that in the comment.
Fixes: 4716909cc5c5 ("cpuset: Track cpusets that use parent's effective_cpus") Signed-off-by: Waiman Long <longman@redhat.com> Tested-by: Phil Auld <pauld@redhat.com> Reviewed-by: Phil Auld <pauld@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While running "./check -I 200 generic/475" it sometimes gives below
kernel BUG(). Ideally we should not call ext4_write_inline_data() if
ext4_create_inline_data() has failed.
<log snip>
[73131.453234] kernel BUG at fs/ext4/inline.c:223!
This patch handles the error and prints out a emergency msg saying potential
data loss for the given inode (since we couldn't restore the original
inline_data due to some previous error).
[ 9571.070313] EXT4-fs (dm-0): error restoring inline_data for inode -- potential data loss! (inode 1703982, error -30)
For now in ext4_mb_new_blocks_simple, if we found a block which
should be excluded then will switch to next group, this may
probably cause 'group' run out of range.
Change to check next block in the same group when get a block should
be excluded. Also change the search range to EXT4_CLUSTERS_PER_GROUP
and add error checking.
During fast commit replay procedure, we clear inode blocks bitmap in
ext4_ext_clear_bb(), this may cause ext4_mb_new_blocks_simple() allocate
blocks still in use.
Make ext4_fc_record_regions() also record physical disk regions used by
inodes during replay procedure. Then ext4_mb_new_blocks_simple() can
excludes these blocks in use.
The driver overrides error codes returned by platform_get_irq_optional()
to -EINVAL for some strange reason, so if it returns -EPROBE_DEFER, the
driver will fail the probe permanently instead of the deferred probing.
Switch to propagating the proper error codes to platform driver code
upwards.
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV for some strange reason, so if it returns -EPROBE_DEFER, the
driver will fail the probe permanently instead of the deferred probing.
Switch to propagating the proper error codes to platform driver code
upwards.
Kyle reported that rr[0] has started to malfunction on Comet Lake and
later CPUs due to EFI starting to make use of CPL3 [1] and the PMU
event filtering not distinguishing between regular CPL3 and SMM CPL3.
Since this is a privilege violation, default disable SMM visibility
where possible.
Administrators wanting to observe SMM cycles can easily change this
using the sysfs attribute while regular users don't have access to
this file.
[0] https://rr-project.org/
[1] See the Intel white paper "Trustworthy SMM on the Intel vPro Platform"
at https://bugzilla.kernel.org/attachment.cgi?id=300300, particularly the
end of page 5.
Reported-by: Kyle Huey <me@kylehuey.com> Suggested-by: Andrew Cooper <Andrew.Cooper3@citrix.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@kernel.org Link: https://lkml.kernel.org/r/YfKChjX61OW4CkYm@hirez.programming.kicks-ass.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a check for !buf->single before calling pt_buffer_region_size in a
place where a missing check can cause a kernel crash.
Fixes a bug introduced by commit 670638477aed ("perf/x86/intel/pt:
Opportunistically use single range output mode"), which added a
support for PT single-range output mode. Since that commit if a PT
stop filter range is hit while tracing, the kernel will crash because
of a null pointer dereference in pt_handle_status due to calling
pt_buffer_region_size without a ToPA configured.
The commit which introduced single-range mode guarded almost all uses of
the ToPA buffer variables with checks of the buf->single variable, but
missed the case where tracing was stopped by the PT hardware, which
happens when execution hits a configured stop filter.
Tested that hitting a stop filter while PT recording successfully
records a trace with this patch but crashes without this patch.
Fixes: 670638477aed ("perf/x86/intel/pt: Opportunistically use single range output mode") Signed-off-by: Tristan Hume <tristan@thume.ca> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Adrian Hunter <adrian.hunter@intel.com> Cc: stable@kernel.org Link: https://lkml.kernel.org/r/20220127220806.73664-1-tristan@thume.ca Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An event may have a number of uncore aliases that when added to the
evlist are consecutive.
If there are multiple uncore events in a group then
parse_events__set_leader_for_uncore_aliase will reorder the evlist so
that events on the same PMU are adjacent.
The collect_all_aliases function assumes that aliases are in blocks so
that only the first counter is printed and all others are marked merged.
The reordering for groups breaks the assumption and so all counts are
printed.
This change removes the assumption from collect_all_aliases
that the events are in blocks and instead processes the entire evlist.
Before:
```
$ perf stat -e '{UNC_CHA_TOR_OCCUPANCY.IA_MISS_DRD_REMOTE,UNC_CHA_TOR_INSERTS.IA_MISS_DRD_REMOTE},duration_time' -a -A -- sleep 1
The intent has always been that perf_event_attr::sig_data should also be
modifiable along with PERF_EVENT_IOC_MODIFY_ATTRIBUTES, because it is
observable by user space if SIGTRAP on events is requested.
Currently only PERF_TYPE_BREAKPOINT is modifiable, and explicitly copies
relevant breakpoint-related attributes in hw_breakpoint_copy_attr().
This misses copying perf_event_attr::sig_data.
Since sig_data is not specific to PERF_TYPE_BREAKPOINT, introduce a
helper to copy generic event-type-independent attributes on
modification.
Fixes: 97ba62b27867 ("perf: Add support for SIGTRAP on perf events") Reported-by: Dmitry Vyukov <dvyukov@google.com> Signed-off-by: Marco Elver <elver@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Reviewed-by: Dmitry Vyukov <dvyukov@google.com> Link: https://lore.kernel.org/r/20220131103407.1971678-1-elver@google.com Signed-off-by: Sasha Levin <sashal@kernel.org>
In kvm_arch_vcpu_ioctl_run() we enter an RCU extended quiescent state
(EQS) by calling guest_enter_irqoff(), and unmasked IRQs prior to
exiting the EQS by calling guest_exit(). As the IRQ entry code will not
wake RCU in this case, we may run the core IRQ code and IRQ handler
without RCU watching, leading to various potential problems.
Additionally, we do not inform lockdep or tracing that interrupts will
be enabled during guest execution, which caan lead to misleading traces
and warnings that interrupts have been enabled for overly-long periods.
This patch fixes these issues by using the new timing and context
entry/exit helpers to ensure that interrupts are handled during guest
vtime but with RCU watching, with a sequence:
guest_timing_enter_irqoff();
guest_state_enter_irqoff();
< run the vcpu >
guest_state_exit_irqoff();
< take any pending IRQs >
guest_timing_exit_irqoff();
Since instrumentation may make use of RCU, we must also ensure that no
instrumented code is run during the EQS. I've split out the critical
section into a new kvm_arm_enter_exit_vcpu() helper which is marked
noinstr.
Fixes: 1b3d546daf85ed2b ("arm/arm64: KVM: Properly account for guest CPU time") Reported-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com> Cc: Alexandru Elisei <alexandru.elisei@arm.com> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Frederic Weisbecker <frederic@kernel.org> Cc: James Morse <james.morse@arm.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Suzuki K Poulose <suzuki.poulose@arm.com> Cc: Will Deacon <will@kernel.org>
Message-Id: <20220201132926.3301912-3-mark.rutland@arm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
When transitioning to/from guest mode, it is necessary to inform
lockdep, tracing, and RCU in a specific order, similar to the
requirements for transitions to/from user mode. Additionally, it is
necessary to perform vtime accounting for a window around running the
guest, with RCU enabled, such that timer interrupts taken from the guest
can be accounted as guest time.
Most architectures don't handle all the necessary pieces, and a have a
number of common bugs, including unsafe usage of RCU during the window
between guest_enter() and guest_exit().
On x86, this was dealt with across commits:
87fa7f3e98a1310e ("x86/kvm: Move context tracking where it belongs") 0642391e2139a2c1 ("x86/kvm/vmx: Add hardirq tracing to guest enter/exit") 9fc975e9efd03e57 ("x86/kvm/svm: Add hardirq tracing on guest enter/exit") 3ebccdf373c21d86 ("x86/kvm/vmx: Move guest enter/exit into .noinstr.text") 135961e0a7d555fc ("x86/kvm/svm: Move guest enter/exit into .noinstr.text") 160457140187c5fb ("KVM: x86: Defer vtime accounting 'til after IRQ handling") bc908e091b326467 ("KVM: x86: Consolidate guest enter/exit logic to common helpers")
... but those fixes are specific to x86, and as the resulting logic
(while correct) is split across generic helper functions and
x86-specific helper functions, it is difficult to see that the
entry/exit accounting is balanced.
This patch adds generic helpers which architectures can use to handle
guest entry/exit consistently and correctly. The guest_{enter,exit}()
helpers are split into guest_timing_{enter,exit}() to perform vtime
accounting, and guest_context_{enter,exit}() to perform the necessary
context tracking and RCU management. The existing guest_{enter,exit}()
heleprs are left as wrappers of these.
Atop this, new guest_state_enter_irqoff() and guest_state_exit_irqoff()
helpers are added to handle the ordering of lockdep, tracing, and RCU
manageent. These are inteneded to mirror exit_to_user_mode() and
enter_from_user_mode().
Subsequent patches will migrate architectures over to the new helpers,
following a sequence:
guest_timing_enter_irqoff();
guest_state_enter_irqoff();
< run the vcpu >
guest_state_exit_irqoff();
< take any pending IRQs >
guest_timing_exit_irqoff();
This sequences handles all of the above correctly, and more clearly
balances the entry and exit portions, making it easier to understand.
The existing helpers are marked as deprecated, and will be removed once
all architectures have been converted.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com> Reviewed-by: Marc Zyngier <maz@kernel.org> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Message-Id: <20220201132926.3301912-2-mark.rutland@arm.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's limiting the year to 2069. When setting the rtc year to 2070,
reading it returns 1970. Evaluate century starting from 19 to count the
correct year.
$ sudo date -s 20700106
Mon 06 Jan 2070 12:00:00 AM CST
$ sudo hwclock -w
$ sudo hwclock -r
1970-01-06 12:00:49.604968+08:00
Fixes: 2a4daadd4d3e5071 ("rtc: cmos: ignore bogus century byte") Signed-off-by: Riwen Lu <luriwen@kylinos.cn> Acked-by: Eric Wong <e@80x24.org> Reviewed-by: Mateusz Jończyk <mat.jonczyk@o2.pl> Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Link: https://lore.kernel.org/r/20220106084609.1223688-1-luriwen@kylinos.cn Signed-off-by: Mateusz Jończyk <mat.jonczyk@o2.pl> # preparation for stable Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have the same LAN controller on different PCH's. Separate ADP board
type from a TGP which will allow for specific fixes to be applied for
ADP platforms.
When building with 'make -s', there is some output from resolve_btfids:
$ make -sj"$(nproc)" oldconfig prepare
MKDIR .../tools/bpf/resolve_btfids/libbpf/
MKDIR .../tools/bpf/resolve_btfids//libsubcmd
LINK resolve_btfids
Silent mode means that no information should be emitted about what is
currently being done. Use the $(silent) variable from Makefile.include
to avoid defining the msg macro so that there is no information printed.
Fixes: fbbb68de80a4 ("bpf: Add resolve_btfids tool to resolve BTF IDs in ELF object") Signed-off-by: Nathan Chancellor <nathan@kernel.org> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220201212503.731732-1-nathan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recursive make commands should always use the variable MAKE, not the
explicit command name ‘make’. This has benefits and removes the
following warning when multiple jobs are used for the build:
make[2]: warning: jobserver unavailable: using -j1. Add '+' to parent make rule.
Fixes: a8ba798bc8ec ("selftests: enable O and KBUILD_OUTPUT") Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com> Reviewed-by: André Almeida <andrealmeid@collabora.com> Signed-off-by: Shuah Khan <skhan@linuxfoundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pipe named FIFO special file is being created in execveat.c to perform
some tests. Makefile doesn't need to do anything with the pipe. When it
isn't found, Makefile generates the following build error:
make: *** No rule to make target
'../tools/testing/selftests/exec/pipe', needed by 'all'. Stop.
After commit 2fd3fb0be1d1 ("kasan, vmalloc: unpoison VM_ALLOC pages
after mapping"), non-VM_ALLOC mappings will be marked as accessible
in __get_vm_area_node() when KASAN is enabled. But now the flag for
ringbuf area is VM_ALLOC, so KASAN will complain out-of-bound access
after vmap() returns. Because the ringbuf area is created by mapping
allocated pages, so use VM_MAP instead.
After the change, info in /proc/vmallocinfo also changes from
[start]-[end] 24576 ringbuf_map_alloc+0x171/0x290 vmalloc user
to
[start]-[end] 24576 ringbuf_map_alloc+0x171/0x290 vmap user
Fixes: 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it") Reported-by: syzbot+5ad567a418794b9b5983@syzkaller.appspotmail.com Signed-off-by: Hou Tao <houtao1@huawei.com> Signed-off-by: Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/bpf/20220202060158.6260-1-houtao1@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 'tail' and 'head' are 'unsigned int' type free-running count, when
'head' is overflow, the 'int i (= tail) < u32 head' will be false:
Only '- loop 0: idx = 63' result is shown, so it needs to use 'int' type
to compare, it can handle the overflow correctly.
typedef uint32_t u32;
int main()
{
u32 tail, head;
int stail, shead;
int i, loop;
tail = 0xffffffff;
head = 0x00000000;
for (i = tail, loop = 0; i < head; i++) {
unsigned int idx = i & 63;
printf("+ loop %d: idx = %u\n", loop++, idx);
}
stail = tail;
shead = head;
for (i = stail, loop = 0; i < shead; i++) {
unsigned int idx = i & 63;
printf("- loop %d: idx = %u\n", loop++, idx);
}
return 0;
}
Fixes: 5cdad90de62c ("gve: Batch AQ commands for creating and destroying queues.") Signed-off-by: Haiyue Wang <haiyue.wang@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
o The server has not recorded an unconfirmed { v, x, c, *, * } and
has recorded a confirmed { v, x, c, *, s }. If the principals of
the record and of SETCLIENTID_CONFIRM do not match, the server
returns NFS4ERR_CLID_INUSE without removing any relevant leased
client state, and without changing recorded callback and
callback_ident values for client { x }.
The current code intends to do what the spec describes above but
it forgot to set 'old' to NULL resulting to the confirmed client
to be expired.
Fixes: 2b63482185e6 ("nfsd: fix clid_inuse on mount with security change") Signed-off-by: Dai Ngo <dai.ngo@oracle.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Reviewed-by: Bruce Fields <bfields@fieldses.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Running tests with a debug kernel shows that bnx2fc_recv_frame() is
modifying the per_cpu lport stats counters in a non-mpsafe way. Just boot
a debug kernel and run the bnx2fc driver with the hardware enabled.
After commit 266423e60ea1 ("pinctrl: bcm2835: Change init order for gpio
hogs") a few error paths would not unwind properly the registration of
gpio ranges. Correct that by assigning a single error label and goto it
whenever we encounter a fatal error.
ASUS Chromebook C223 with Celeron N3350 crashes sometimes during
cold booot. Inspection of the kernel log showed that it gets into
an inifite loop logging the following message:
->handle_irq(): 000000009cdb51e8, handle_bad_irq+0x0/0x251
->irq_data.chip(): 000000005ec212a7, 0xffffa043009d8e7
->action(): 00000
IRQ_NOPROBE set
unexpected IRQ trap at vector 7c
The issue happens during cold boot but only if cold boot happens
at most several dozen seconds after Chromebook is powered off. For
longer intervals between power off and power on (cold boot) the issue
does not reproduce. The unexpected interrupt is sourced from INT3452
GPIO pin which is used for SD card detect. Investigation relevealed
that when the interval between power off and power on (cold boot)
is less than several dozen seconds then values of INT3452 GPIO interrupt
enable and interrupt pending registers survive power off and power
on sequence and interrupt for SD card detect pin is enabled and pending
during probe of SD controller which causes the unexpected IRQ message.
"Intel Pentium and Celeron Processor N- and J- Series" volume 3 doc
mentions that GPIO interrupt enable and status registers default
value is 0x0.
The fix clears INT3452 GPIO interrupt enabled and interrupt pending
registers in its probe function.
The commit af7e3eeb84e2 ("pinctrl: intel: Disable input and output buffer
when switching to GPIO") hadn't taken into account an update of the IRQ
flags scenario.
When updating the IRQ flags on the preconfigured line the ->irq_set_type()
is called again. In such case the sequential Rx buffer configuration
changes may trigger a falling or rising edge interrupt that may lead,
on some platforms, to an undesired event.
This may happen because each of intel_gpio_set_gpio_mode() and
__intel_gpio_set_direction() updates the pad configuration with a different
value of the GPIORXDIS bit. Notable, that the intel_gpio_set_gpio_mode() is
called only for the pads that are configured as an input. Due to this fact,
integrate the logic of __intel_gpio_set_direction() call into the
intel_gpio_set_gpio_mode() so that the Rx buffer won't be disabled and
immediately re-enabled.
Fixes: af7e3eeb84e2 ("pinctrl: intel: Disable input and output buffer when switching to GPIO") Reported-by: Kane Chen <kane.chen@intel.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Grace Kao <grace.kao@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two bugs have sneaked in the H616 pinctrl data:
- PH9 uses the mux value of 0x3 twice (one should be 0x5 instead)
- PH8 and PH9 use the "i2s3" function name twice in each pin
For the double pin name we use the same trick we pulled for i2s0: append
the pin function to the group name to designate the special function.
Fixes: 25adc29407fb ("pinctrl: sunxi: Add support for the Allwinner H616 pin controller") Reported-by: SASANO Takayoshi <uaa@mx5.nisiq.net> Signed-off-by: Andre Przywara <andre.przywara@arm.com> Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com> Reviewed-by: Samuel Holland <samuel@sholland.org> Link: https://lore.kernel.org/r/20220105172952.23347-1-andre.przywara@arm.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
wcd938x_ear_pa_put_gain, wcd938x_set_swr_port and wcd938x_set_compander
currently returns zero eventhough it changes the value.
Fix this, so that change notifications are sent correctly.
For some reason we ended up with incorrect register offfset calcuations
for sidetone. regmap clearly throw errors when accessing these incorrect
registers as these do not belong to any read/write ranges.
so fix them to point to correct register offsets.
Mixer controls have the channel id in mixer->reg, which is not same
as port id. port id should be derived from chan_info array.
So fix this. Without this, its possible that we could corrupt
struct wcd938x_sdw_priv by accessing port_map array out of range
with channel id instead of port id.
Check for negative values of "priv->gain" to prevent an out of bounds
access. The concern is that these might come from the user via:
-> snd_ctl_elem_write_user()
-> snd_ctl_elem_write()
-> kctl->put()
Fixes: fa8d915172b8 ("ASoC: max9759: Add Amplifier Driver") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20220119123101.GA9509@kili Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the device does not exist, of_get_child_by_name() will return NULL
pointer.
And devm_snd_soc_register_component() does not check it.
Also, I have noticed that cpcap_codec_driver has not been used yet.
Therefore, it should be better to check it in order to avoid the future
dereference of the NULL pointer.
Fixes: f6cdf2d3445d ("ASoC: cpcap: new codec") Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn> Link: https://lore.kernel.org/r/20220111025048.524134-1-jiasheng@iscas.ac.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A previous change to simple-card resulted in asoc_simple_parse_dai
attempting to retrieve the dai_name for platform components, which are
unlikely to have a valid DAI name. This caused simple-card to fail to
probe when using the xlnx_formatter_pcm as the platform component, since
it does not register any DAI components.
Since the dai_name is not used for platform components, just skip trying
to retrieve it for those.
Fixes: f107294c6422 ("ASoC: simple-card: support snd_soc_dai_link_component style for cpu") Signed-off-by: Robert Hancock <robert.hancock@calian.com> Link: https://lore.kernel.org/r/20220107214711.1100162-6-robert.hancock@calian.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is based on one in the Xilinx kernel tree, "ASoc: xlnx: Make
buffer bytes multiple of period bytes" by Devarsh Thakkar. The same
issue exists in the mainline version of the driver. The original
patch description is as follows:
"The Xilinx Audio Formatter IP has a constraint on period
bytes to be multiple of 64. This leads to driver changing
the period size to suitable frames such that period bytes
are multiple of 64.
Now since period bytes and period size are updated but not
the buffer bytes, this may make the buffer bytes unaligned
and not multiple of period bytes.
When this happens we hear popping noise as while DMA is being
done the buffer bytes are not enough to complete DMA access
for last period of frame within the application buffer boundary.
To avoid this, align buffer bytes too as multiple of 64, and
set another constraint to always enforce number of periods as
integer. Now since, there is already a rule in alsa core
to enforce Buffer size = Number of Periods * Period Size
this automatically aligns buffer bytes as multiple of period
bytes."
Fixes: 6f6c3c36f091 ("ASoC: xlnx: add pcm formatter platform driver") Cc: Devarsh Thakkar <devarsh.thakkar@xilinx.com> Signed-off-by: Robert Hancock <robert.hancock@calian.com> Link: https://lore.kernel.org/r/20220107214711.1100162-2-robert.hancock@calian.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dGPUs connected to Intel systems configured for suspend to idle
will not have the power rails cut at suspend and resetting the GPU
may lead to problematic behaviors.
Fixes: e25443d2765f4 ("drm/amdgpu: add a dev_pm_ops prepare callback (v2)") Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1879 Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Smatch detected a divide by zero bug in check_overlay_scaling().
drivers/gpu/drm/i915/display/intel_overlay.c:976 check_overlay_scaling()
error: potential divide by zero bug '/ rec->dst_height'.
drivers/gpu/drm/i915/display/intel_overlay.c:980 check_overlay_scaling()
error: potential divide by zero bug '/ rec->dst_width'.
Prevent this by ensuring that the dst height and width are non-zero.
Fixes: 02e792fbaadb ("drm/i915: implement drmmode overlay support v4") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220124122409.GA31673@kili
(cherry picked from commit cf5b64f7f10b28bebb9b7c9d25e7aee5cbe43918) Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even if protected from preemption and interrupts, a small time window
remains when the 2 register reads could return inconsistent values,
each time the "seconds" register changes. This could lead to an about
1-second error in the reported time.
Add logic to ensure the "seconds" and "nanoseconds" values are consistent.
Fixes: 92ba6888510c ("stmmac: add the support for PTP hw clock driver") Signed-off-by: Yannick Vignon <yannick.vignon@nxp.com> Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Link: https://lore.kernel.org/r/20220203160025.750632-1-yannick.vignon@oss.nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike gmac100, gmac1000, gmac4 has 27 DMA registers and they are
located at DMA_CHAN_BASE_ADDR (0x1100). In order for ethtool to dump
gmac4 DMA registers correctly, this commit checks if a net_device has
gmac4 and uses different logic to dump its DMA registers.
This fixes the following KASAN warning, which can normally be triggered
by a command similar like "ethtool -d eth0":
BUG: KASAN: vmalloc-out-of-bounds in dwmac4_dump_dma_regs+0x6d4/0xb30
Write of size 4 at addr ffffffc010177100 by task ethtool/1839
kasan_report+0x200/0x21c
__asan_report_store4_noabort+0x34/0x60
dwmac4_dump_dma_regs+0x6d4/0xb30
stmmac_ethtool_gregs+0x110/0x204
ethtool_get_regs+0x200/0x4b0
dev_ethtool+0x1dac/0x3800
dev_ioctl+0x7c0/0xb50
sock_ioctl+0x298/0x6c4
...
When setting Tx sci explicit, the Rx side is expected to use this
sci and not recalculate it from the packet.However, in case of Tx sci
is explicit and send_sci is off, the receiver is wrongly recalculate
the sci from the source MAC address which most likely be different
than the explicit sci.
Fix by preventing such configuration when macsec newlink is established
and return EINVAL error code on such cases.
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver") Signed-off-by: Lior Nahmanson <liorna@nvidia.com> Reviewed-by: Raed Salem <raeds@nvidia.com> Signed-off-by: Raed Salem <raeds@nvidia.com> Link: https://lore.kernel.org/r/1643542672-29403-1-git-send-email-raeds@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current macsec netdev notify handler handles NETDEV_UNREGISTER event by
releasing relevant SW resources only, this causes resources leak in case
of macsec HW offload, as the underlay driver was not notified to clean
it's macsec offload resources.
Fix by calling the underlay driver to clean it's relevant resources
by moving offload handling from macsec_dellink() to macsec_common_dellink()
when handling NETDEV_UNREGISTER event.
Fixes: 3cf3227a21d1 ("net: macsec: hardware offloading infrastructure") Signed-off-by: Lior Nahmanson <liorna@nvidia.com> Reviewed-by: Raed Salem <raeds@nvidia.com> Signed-off-by: Raed Salem <raeds@nvidia.com> Reviewed-by: Antoine Tenart <atenart@kernel.org> Link: https://lore.kernel.org/r/1643542141-28956-1-git-send-email-raeds@nvidia.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two issues with runtime pm handling in stmmac_dvr_remove():
1. the mac is runtime suspended before stopping dma and rx/tx. We
need to ensure the device is properly resumed back.
2. the stmmaceth clk enable/disable isn't balanced in both exit and
error handling code path. Take the exit code path for example, when we
unbind the driver or rmmod the driver module, the mac is runtime
suspended as said above, so the stmmaceth clk is disabled, but
stmmac_dvr_remove()
stmmac_remove_config_dt()
clk_disable_unprepare()
CCF will complain this time. The error handling code path suffers
from the similar situtaion.
Here are kernel warnings in error handling code path on Allwinner D1
platform:
Variable clk_sel_val is not initialized in the default case of the first switch statement.
In that case, the function should return immediately without any changes to the hardware.
Reported-by: kernel test robot <lkp@intel.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: b38dd98ff8d0 ("net: stmmac: Add Toshiba Visconti SoCs glue driver") Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp> Reviewed-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we replace TCP with SMC and a fallback occurs, there may be
some socket waitqueue entries remaining in smc socket->wq, such
as eppoll_entries inserted by userspace applications.
After the fallback, data flows over TCP/IP and only clcsocket->wq
will be woken up. Applications can't be notified by the entries
which were inserted in smc socket->wq before fallback. So we need
a mechanism to wake up smc socket->wq at the same time if some
entries remaining in it.
The current workaround is to transfer the entries from smc socket->wq
to clcsock->wq during the fallback. But this may cause a crash
like this:
The crash is caused by privately transferring waitqueue entries from
smc socket->wq to clcsock->wq. The owners of these entries, such as
epoll, have no idea that the entries have been transferred to a
different socket wait queue and still use original waitqueue spinlock
(smc socket->wq.wait.lock) to make the entries operation exclusive,
but it doesn't work. The operations to the entries, such as removing
from the waitqueue (now is clcsock->wq after fallback), may cause a
crash when clcsock waitqueue is being iterated over at the moment.
This patch tries to fix this by no longer transferring wait queue
entries privately, but introducing own implementations of clcsock's
callback functions in fallback situation. The callback functions will
forward the wakeup to smc socket->wq if clcsock->wq is actually woken
up and smc socket->wq has remaining entries.
Fixes: 2153bd1e3d3d ("net/smc: Transfer remaining wait queue entries during fallback") Suggested-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Wen Gu <guwen@linux.alibaba.com> Acked-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to commit fa538f7cf05aa ("netfilter: nf_reject: add reject skbuff
creation helpers"), nft_reject_bridge did not assign to nskb->dev before
passing nskb on to br_forward(). The shared skbuff creation helpers
introduced in above commit do which seems to confuse br_forward() as
reject statements in prerouting hook won't emit a packet anymore.
Fix this by simply passing NULL instead of 'dev' to the helpers - they
use the pointer for just that assignment, nothing else.
These periods are expressed in time units (microseconds) while 40 and 12
are the number of symbol durations these periods will last. We need to
multiply them both with phy->symbol_duration in order to get these
values in microseconds.
Drivers are expected to set the PHY current_channel and current_page
according to their default state. The hwsim driver is advertising being
configured on channel 13 by default but that is not reflected in its own
internal pib structure. In order to ensure that this driver consider the
current channel as being 13 internally, we at least need to set the
pib->channel field to 13.
Fixes: f25da51fdc38 ("ieee802154: hwsim: add replacement for fakelb") Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[stefan@datenfreihafen.org: fixed assigment from page to channel] Acked-by: Alexander Aring <aahringo@redhat.com> Link: https://lore.kernel.org/r/20220125121426.848337-2-miquel.raynal@bootlin.com Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 7345201c3963 ("IB/cm: Improve the calling of cm_init_av_for_lap and cm_init_av_by_path") Link: https://lore.kernel.org/r/7615f23bbb5c5b66d03f6fa13e1c99d51dae6916.1642581448.git.leonro@nvidia.com Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mark Zhang <markzhang@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The issue happens in several error paths in uniphier_spi_probe().
When either dma_get_slave_caps() or devm_spi_register_master() returns
an error code, the function forgets to decrease the refcount of both
`dma_rx` and `dma_tx` objects, which may lead to refcount leaks.
Fix it by decrementing the reference count of specific objects in
those error paths.
Signed-off-by: Xin Xiong <xiongx18@fudan.edu.cn> Signed-off-by: Xiyu Yang <xiyuyang19@fudan.edu.cn> Signed-off-by: Xin Tan <tanxin.ctf@gmail.com> Reviewed-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Fixes: 28d1dddc59f6 ("spi: uniphier: Add DMA transfer mode support") Link: https://lore.kernel.org/r/20220125101214.35677-1-xiongx18@fudan.edu.cn Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This check misses checking for platform_get_irq()'s call and may passes
the negative error codes to devm_request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Stop calling devm_request_irq() with invalid IRQ #s.
Fixes: 454fa271bc4e ("spi: Add Meson SPICC driver") Signed-off-by: Miaoqian Lin <linmq006@gmail.com> Link: https://lore.kernel.org/r/20220126110447.24549-1-linmq006@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In some case, like after a transfer timeout, master->cur_msg pointer
is NULL which led to a kernel crash when trying to use master->cur_msg->spi.
mtk_spi_can_dma(), pointed by master->can_dma, doesn't use this parameter
avoid the problem by setting NULL as second parameter.
Fixes: a568231f46322 ("spi: mediatek: Add spi bus for Mediatek MT8173") Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com> Link: https://lore.kernel.org/r/20220131141708.888710-1-benjamin.gaignard@collabora.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apply only valid chip select value. This change fixes case where chip
select is set to initial value of '-1' during probe and PM supend and
subsequent resume can try to use the value with undefined behaviour.
Also in case where gpio based chip select, the check in
bcm_qspi_chip_select() shall prevent undefined behaviour on resume.
Fixes: fa236a7ef240 ("spi: bcm-qspi: Add Broadcom MSPI driver") Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220127185359.27322-1-kdasu.kdev@gmail.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The polling loop for the register change in iommu_ga_log_enable() needs
to have a udelay() in it. Otherwise the CPU might be faster than the
IOMMU hardware and wrongly trigger the WARN_ON() further down the code
stream. Use a 10us for udelay(), has there is some hardware where
activation of the GA log can take more than a 100ms.
A future optimization should move the activation check of the GA log
to the point where it gets used for the first time. But that is a
bigger change and not suitable for a fix.
After commit e3beca48a45b ("irqdomain/treewide: Keep firmware node
unconditionally allocated"). For tear down scenario, fn is only freed
after fail to allocate ir_domain, though it also should be freed in case
dmar_enable_qi returns error.
Besides free fn, irq_domain and ir_msi_domain need to be removed as well
if intel_setup_irq_remapping fails to enable queued invalidation.
Improve the rewinding path by add out_free_ir_domain and out_free_fwnode
lables per Baolu's suggestion.
The %x format of sscanf() takes an unsigned int pointer, while we pass
a signed int pointer. Practically it's OK, but this may result in a
compile warning. Let's fix it.
Fixes: a235d5b8e550 ("ALSA: hda: Allow model option to specify PCI SSID alias") Reported-by: kernel test robot <lkp@intel.com> Link: https://lore.kernel.org/r/20220127135717.31751-1-tiwai@suse.de Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
clang static analysis reports this representative issue
mixer.c:1548:35: warning: Assigned value is garbage or undefined
ucontrol->value.integer.value[0] = val;
^ ~~~
The filter_error() macro allows errors to be ignored.
If errors can be ignored, initialize variables
so garbage will not be used.
The failure to allocate memory during MLX4_DEV_EVENT_PORT_MGMT_CHANGE
event handler will cause skip the assignment logic, but
ib_dispatch_event() will be called anyway.
Fix it by calling to return instead of break after memory allocation
failure.
Fixes: 00f5ce99dc6e ("mlx4: Use port management change event instead of smp_snoop") Link: https://lore.kernel.org/r/12a0e83f18cfad4b5f62654f141e240d04915e10.1643622264.git.leonro@nvidia.com Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Code unconditionally resumed fenced SQ processing after next RDMA Read
completion, even if other RDMA Read responses are still outstanding, or
ORQ is full. Also adds comments for better readability of fence
processing, and removes orq_get_tail() helper, which is not needed
anymore.
Fixes: 8b6a361b8c48 ("rdma/siw: receive path") Fixes: a531975279f3 ("rdma/siw: main include file") Link: https://lore.kernel.org/r/20220130170815.1940-1-bmt@zurich.ibm.com Reported-by: Jared Holzman <jared.holzman@excelero.com> Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Partially revert the commit mentioned in the Fixes line to make sure that
allocation and erasing multicast struct are locked.
BUG: KASAN: use-after-free in ucma_cleanup_multicast drivers/infiniband/core/ucma.c:491 [inline]
BUG: KASAN: use-after-free in ucma_destroy_private_ctx+0x914/0xb70 drivers/infiniband/core/ucma.c:579
Read of size 8 at addr ffff88801bb74b00 by task syz-executor.1/25529
CPU: 0 PID: 25529 Comm: syz-executor.1 Not tainted 5.16.0-rc7-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
print_address_description.constprop.0.cold+0x8d/0x320 mm/kasan/report.c:247
__kasan_report mm/kasan/report.c:433 [inline]
kasan_report.cold+0x83/0xdf mm/kasan/report.c:450
ucma_cleanup_multicast drivers/infiniband/core/ucma.c:491 [inline]
ucma_destroy_private_ctx+0x914/0xb70 drivers/infiniband/core/ucma.c:579
ucma_destroy_id+0x1e6/0x280 drivers/infiniband/core/ucma.c:614
ucma_write+0x25c/0x350 drivers/infiniband/core/ucma.c:1732
vfs_write+0x28e/0xae0 fs/read_write.c:588
ksys_write+0x1ee/0x250 fs/read_write.c:643
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
Currently the xarray search can touch a concurrently freeing mc as the
xa_for_each() is not surrounded by any lock. Rather than hold the lock for
a full scan hold it only for the effected items, which is usually an empty
list.
Fixes: 95fe51096b7a ("RDMA/ucma: Remove mc_list and rely on xarray") Link: https://lore.kernel.org/r/1cda5fabb1081e8d16e39a48d3a4f8160cea88b8.1642491047.git.leonro@nvidia.com Reported-by: syzbot+e3f96c43d19782dd14a7@syzkaller.appspotmail.com Suggested-by: Jason Gunthorpe <jgg@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In RoCE we should use cma_iboe_set_mgid() and not cma_set_mgid to generate
the mgid, otherwise we will generate an IGMP for an incorrect address.
Fixes: b5de0c60cc30 ("RDMA/cma: Fix use after free race in roce multicast join") Link: https://lore.kernel.org/r/913bc6783fd7a95fe71ad9454e01653ee6fb4a9a.1642491047.git.leonro@nvidia.com Signed-off-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Leon Romanovsky <leonro@nvidia.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to commit defe21f49bc9 ("KVM: arm64: Move PC rollback on SError to
HYP"), when an SError is synchronised due to another exception, KVM
handles the SError first. If the guest survives, the instruction that
triggered the original exception is re-exectued to handle the first
exception. HVC is treated as a special case as the instruction wouldn't
normally be re-exectued, as its not a trap.
Commit defe21f49bc9 didn't preserve the behaviour of the 'return 1'
that skips the rest of handle_exit().
Since commit defe21f49bc9, KVM will try to handle the SError and the
original exception at the same time. When the exception was an HVC,
fixup_guest_exit() has already rolled back ELR_EL2, meaning if the
guest has virtual SError masked, it will execute and handle the HVC
twice.
Restore the original behaviour.
Fixes: defe21f49bc9 ("KVM: arm64: Move PC rollback on SError to HYP") Cc: stable@vger.kernel.org Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20220127122052.1584324-4-james.morse@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When any exception other than an IRQ occurs, the CPU updates the ESR_EL2
register with the exception syndrome. An SError may also become pending,
and will be synchronised by KVM. KVM notes the exception type, and whether
an SError was synchronised in exit_code.
When an exception other than an IRQ occurs, fixup_guest_exit() updates
vcpu->arch.fault.esr_el2 from the hardware register. When an SError was
synchronised, the vcpu esr value is used to determine if the exception
was due to an HVC. If so, ELR_EL2 is moved back one instruction. This
is so that KVM can process the SError first, and re-execute the HVC if
the guest survives the SError.
But if an IRQ synchronises an SError, the vcpu's esr value is stale.
If the previous non-IRQ exception was an HVC, KVM will corrupt ELR_EL2,
causing an unrelated guest instruction to be executed twice.
Check ARM_EXCEPTION_CODE() before messing with ELR_EL2, IRQs don't
update this register so don't need to check.
Fixes: defe21f49bc9 ("KVM: arm64: Move PC rollback on SError to HYP") Cc: stable@vger.kernel.org Reported-by: Steven Price <steven.price@arm.com> Signed-off-by: James Morse <james.morse@arm.com> Signed-off-by: Marc Zyngier <maz@kernel.org> Link: https://lore.kernel.org/r/20220127122052.1584324-3-james.morse@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With this patch in the tree, Chromebooks running the affected hardware
no longer boot. Bisect points to this patch, and reverting it fixes
the problem.
An analysis of the code with this patch applied shows:
ret = init_clks(pdev, clk);
if (ret)
return ERR_PTR(ret);
...
for (j = 0; j < MAX_CLKS && data->clk_id[j]; j++) {
struct clk *c = clk[data->clk_id[j]];
Not all clocks in the clk_names array have to be present. Only the clocks
in the data->clk_id array are actually needed. The code already checks if
the required clocks are available and bails out if not. The assumption that
all clocks have to be present is wrong, and commit 9de2b9286a6d needs to be
reverted.
Fixes: 9de2b9286a6d ("ASoC: mediatek: Check for error clk pointer") Cc: Jiasheng Jiang <jiasheng@iscas.ac.cn> Cc: Mark Brown <broonie@kernel.org> Cc: James Liao <jamesjj.liao@mediatek.com> Cc: Kevin Hilman <khilman@baylibre.com> Cc: Matthias Brugger <matthias.bgg@gmail.com Cc: Frank Wunderlich <frank-w@public-files.de> Cc: Daniel Golle <daniel@makrotopia.org> Link: https://lore.kernel.org/lkml/20220205014755.699603-1-linux@roeck-us.net/ Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The MPTCP endpoint list is under RCU protection, guarded by the
pernet spinlock. mptcp_nl_cmd_set_flags() traverses the list
without acquiring the spin-lock nor under the RCU critical section.
This change addresses the issue performing the lookup and the endpoint
update under the pernet spinlock.
[The upstream commit had to handle a lookup_by_id variable that is only
present in 5.17. This version of the patch removes that variable, so
the __lookup_addr() function only handles the lookup as it is
implemented in 5.15 and 5.16. It also removes one 'const' keyword to
prevent a warning due to differing const-ness in the 5.17 version of
addresses_equal().]
Fixes: 0f9f696a502e ("mptcp: add set_flags command in PM netlink") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a config option CONFIG_FRAMEBUFFER_CONSOLE_LEGACY_ACCELERATION to
enable bitblt and fillrect hardware acceleration in the framebuffer
console. If disabled, such acceleration will not be used, even if it is
supported by the graphics hardware driver.
If you plan to use DRM as your main graphics output system, you should
disable this option since it will prevent compiling in code which isn't
used later on when DRM takes over.
For all other configurations, e.g. if none of your graphic cards support
DRM (yet), DRM isn't available for your architecture, or you can't be
sure that the graphic card in the target system will support DRM, you
most likely want to enable this option.
In the non-accelerated case (e.g. when DRM is used), the inlined
fb_scrollmode() function is hardcoded to return SCROLL_REDRAW and as such the
compiler is able to optimize much unneccesary code away.
In this v3 patch version I additionally changed the GETVYRES() and GETVXRES()
macros to take a pointer to the fbcon_display struct. This fixes the build when
console rotation is enabled and helps the compiler again to optimize out code.
Revert the first (of 2) commits which disabled scrolling acceleration in
fbcon/fbdev. It introduced a regression for fbdev-supported graphic cards
because of the performance penalty by doing screen scrolling by software
instead of using the existing graphic card 2D hardware acceleration.
Console scrolling acceleration was disabled by dropping code which
checked at runtime the driver hardware capabilities for the
BINFO_HWACCEL_COPYAREA or FBINFO_HWACCEL_FILLRECT flags and if set, it
enabled scrollmode SCROLL_MOVE which uses hardware acceleration to move
screen contents. After dropping those checks scrollmode was hard-wired
to SCROLL_REDRAW instead, which forces all graphic cards to redraw every
character at the new screen position when scrolling.
This change effectively disabled all hardware-based scrolling acceleration for
ALL drivers, because now all kind of 2D hardware acceleration (bitblt,
fillrect) in the drivers isn't used any longer.
The original commit message mentions that only 3 DRM drivers (nouveau, omapdrm
and gma500) used hardware acceleration in the past and thus code for checking
and using scrolling acceleration is obsolete.
This statement is NOT TRUE, because beside the DRM drivers there are around 35
other fbdev drivers which depend on fbdev/fbcon and still provide hardware
acceleration for fbdev/fbcon.
The original commit message also states that syzbot found lots of bugs in fbcon
and thus it's "often the solution to just delete code and remove features".
This is true, and the bugs - which actually affected all users of fbcon,
including DRM - were fixed, or code was dropped like e.g. the support for
software scrollback in vgacon (commit 973c096f6a85).
So to further analyze which bugs were found by syzbot, I've looked through all
patches in drivers/video which were tagged with syzbot or syzkaller back to
year 2005. The vast majority fixed the reported issues on a higher level, e.g.
when screen is to be resized, or when font size is to be changed. The few ones
which touched driver code fixed a real driver bug, e.g. by adding a check.
But NONE of those patches touched code of either the SCROLL_MOVE or the
SCROLL_REDRAW case.
That means, there was no real reason why SCROLL_MOVE had to be ripped-out and
just SCROLL_REDRAW had to be used instead. The only reason I can imagine so far
was that SCROLL_MOVE wasn't used by DRM and as such it was assumed that it
could go away. That argument completely missed the fact that SCROLL_MOVE is
still heavily used by fbdev (non-DRM) drivers.
Some people mention that using memcpy() instead of the hardware acceleration is
pretty much the same speed. But that's not true, at least not for older graphic
cards and machines where we see speed decreases by factor 10 and more and thus
this change leads to console responsiveness way worse than before.
That's why the original commit is to be reverted. By reverting we
reintroduce hardware-based scrolling acceleration and fix the
performance regression for fbdev drivers.
There isn't any impact on DRM when reverting those patches.
The panic happens in hfi1_ipoib_txreq_deinit() because there is a NULL
deref when hfi1_ipoib_netdev_dtor() is called in this error case.
hfi1_ipoib_txreq_init() and hfi1_ipoib_rxq_init() are self unwinding so
fix by adjusting the error paths accordingly.
Other changes:
- hfi1_ipoib_free_rdma_netdev() is deleted including the free_netdev()
since the netdev core code deletes calls free_netdev()
- The switch to the accelerated entrances is moved to the success path.
Cc: stable@vger.kernel.org Fixes: d99dc602e2a5 ("IB/hfi1: Add functions to transmit datagram ipoib packets") Link: https://lore.kernel.org/r/1642287756-182313-4-git-send-email-mike.marciniszyn@cornelisnetworks.com Reviewed-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It appears like nr could be a Spectre v1 gadget as it's supplied by a
user and used as an array index. Prevent the contents
of kernel memory from being leaked to userspace via speculative
execution by using array_index_nospec.
Commit 309a62fa3a9e ("bio-integrity: bio_integrity_advance must update
integrity seed") added code to update the integrity seed value when
advancing a bio. However, it failed to take into account that the
integrity interval might be larger than the 512-byte block layer
sector size. This broke bio splitting on PI devices with 4KB logical
blocks.
The seed value should be advanced by bio_integrity_intervals() and not
the number of sectors.
When using devm_request_free_mem_region() and devm_memremap_pages() to
add ZONE_DEVICE memory, if requested free mem region's end pfn were
huge(e.g., 0x400000000), the node_end_pfn() will be also huge (see
move_pfn_range_to_zone()). Thus it creates a huge hole between
node_start_pfn() and node_end_pfn().
We found on some AMD APUs, amdkfd requested such a free mem region and
created a huge hole. In such a case, following code snippet was just
doing busy test_bit() looping on the huge hole.
for (pfn = start_pfn; pfn < end_pfn; pfn++) {
struct page *page = pfn_to_online_page(pfn);
if (!page)
continue;
...
}
Since commit 974b9b2c68f3 ("mm: consolidate pte_index() and
pte_offset_*() definitions") pte_index is a static inline and there is
no define for it that can be recognized by the preprocessor. As a
result, vm_insert_pages() uses slower loop over vm_insert_page() instead
of insert_pages() that amortizes the cost of spinlock operations when
inserting multiple pages.
Link: https://lkml.kernel.org/r/20220111145457.20748-1-rppt@kernel.org Fixes: 974b9b2c68f3 ("mm: consolidate pte_index() and pte_offset_*() definitions") Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Reported-by: Christian Dietrich <stettberger@dokucode.de> Reviewed-by: Khalid Aziz <khalid.aziz@oracle.com> Cc: <stable@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Controller deletion/reset, immediately followed by or concurrent with
a reconnect, is hard failing the connect attempt resulting in a
complete loss of connectivity to the controller.
In the connect request, fabrics looks for an existing controller with
the same address components and aborts the connect if a controller
already exists and the duplicate connect option isn't set. The match
routine filters out controllers that are dead or dying, so they don't
interfere with the new connect request.
When NVME_CTRL_DELETING_NOIO was added, it missed updating the state
filters in the nvmf_ctlr_matches_baseopts() routine. Thus, when in this
new state, it's seen as a live controller and fails the connect request.
Correct by adding the DELETING_NIO state to the match checks.
Fixes: ecca390e8056 ("nvme: fix deadlock in disconnect during scan_work and/or ana_work") Cc: <stable@vger.kernel.org> # v5.7+ Signed-off-by: Uday Shankar <ushankar@purestorage.com> Reviewed-by: James Smart <jsmart2021@gmail.com> Reviewed-by: Sagi Grimberg <sagi@grimberg.me> Signed-off-by: Christoph Hellwig <hch@lst.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The eDP link rate reported by the DP_MAX_LINK_RATE dpcd register (0xa) is
contradictory to the highest rate supported reported by
EDID (0xc = LINK_RATE_RBR2). The effects of this compounded with commit
'4a8ca46bae8a ("drm/amd/display: Default max bpc to 16 for eDP")' results
in no display modes being found and a dark panel.
For now, simply force the maximum supported link rate for the eDP attached
2018 15" Apple Retina panels.
Additionally, we must also check the firmware revision since the device ID
reported by the DPCD is identical to that of the more capable 16,1,
incorrectly quirking it. We also use said firmware check to quirk the
refreshed 15,1 models with Vega graphics as they use a slightly newer
firmware version.
Tested-by: Aun-Ali Zaidi <admin@kodeit.net> Reviewed-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Aun-Ali Zaidi <admin@kodeit.net> Signed-off-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TCSS_DDI_STATUS register is indexed by tc_port not by the FIA port
index, fix this up. This only caused an issue on TC#3/4 ports in legacy
mode, as in all other cases the two indices either match (on TC#1/2) or
the TCSS_DDI_STATUS_READY flag is set regardless of something being
connected or not (on TC#1/2/3/4 in dp-alt and tbt-alt modes).
Reported-and-tested-by: Chia-Lin Kao (AceLan) <acelan.kao@canonical.com> Fixes: 55ce306c2aa1 ("drm/i915/adl_p: Implement TC sequences") Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4698 Cc: José Roberto de Souza <jose.souza@intel.com> Cc: <stable@vger.kernel.org> # v5.14+ Signed-off-by: Imre Deak <imre.deak@intel.com> Reviewed-by: José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220126104356.2022975-1-imre.deak@intel.com
(cherry picked from commit 516b33460c5bee78b2055637b0547bdb0e6af754) Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bounds checking when parsing init scripts embedded in the BIOS reject
access to the last byte. This causes driver initialization to fail on
Apple eMac's with GeForce 2 MX GPUs, leaving the system with no working
console.
This is probably only seen on OpenFirmware machines like PowerPC Macs
because the BIOS image provided by OF is only the used parts of the ROM,
not a power-of-two blocks read from PCI directly so PCs always have
empty bytes at the end that are never accessed.
Signed-off-by: Nick Lopez <github@glowingmonkey.org> Fixes: 4d4e9907ff572 ("drm/nouveau/bios: guard against out-of-bounds accesses to image") Cc: <stable@vger.kernel.org> # v4.10+ Reviewed-by: Ilia Mirkin <imirkin@alum.mit.edu> Reviewed-by: Karol Herbst <kherbst@redhat.com> Signed-off-by: Karol Herbst <kherbst@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220122081906.2633061-1-github@glowingmonkey.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That commit was meant as a fix for setattrs with by fd (e.g. ftruncate)
to use an open fid instead of the first fid it found on lookup.
The proper fix for that is to use the fid associated with the open file
struct, available in iattr->ia_file for such operations, and was
actually done just before in 66246641609b ("9p: retrieve fid from file
when file instance exist.")
As such, this commit is no longer required.
Furthermore, changing lookup to return open fids first had unwanted side
effects, as it turns out the protocol forbids the use of open fids for
further walks (e.g. clone_fid) and we broke mounts for some servers
enforcing this rule.
Note this only reverts to the old working behaviour, but it's still
possible for lookup to return open fids if dentry->d_fsdata is not set,
so more work is needed to make sure we respect this rule in the future,
for example by adding a flag to the lookup functions to only match
certain fid open modes depending on caller requirements.