Legion Y9000X 2020 has a speaker, but the speaker doesn't work.
This can be fixed by applying alc285_fixup_ideapad_s740_coef
to fix the speaker's coefficients.
Besides, to support the transition between the speaker and the headphone,
alc287_fixup_legion_15imhg05_speakers needs to be run.
HDA regression is recently reported on Tegra194 based platforms.
This happens because "hda2codec_2x" reset does not really exist
in Tegra194 and it causes probe failure. All the HDA based audio
tests fail at the moment. This underlying issue is exposed by
commit c045ceb5a145 ("reset: tegra-bpmp: Handle errors in BPMP
response") which now checks return code of BPMP command response.
Fix this issue by skipping unavailable reset on Tegra194.
The speaker fixup that is used for the Yoga 7 14ITL5 also applies to
the IdeaPad Slim 9i 14ITL5. The attached patch applies the quirk to
initialise the amplifier on the IdeaPad Slim 9i as well.
This patch addresses an issue where after rebooting from Windows into Linux
there would be no audio output.
It turns out that the Realtek Audio driver on Windows changes some coeffs
which are not being reset/reinitialized when rebooting the machine. As a
result, there is no audio output until these coeffs are being reset to
their initial state. This patch takes care of that by setting known-good
(initial) values to the coeffs.
We initially relied upon alc1220_fixup_clevo_p950() to fix some pins in the
connection list. However, it also sets coef 0x7 which does not need to be
touched. Furthermore, to prevent mixing device-specific quirks I introduced
a new alc1220_fixup_gb_x570() which is heavily based on
alc1220_fixup_clevo_p950() but does not set coeff 0x7 and fixes the coeffs
that are actually needed instead.
This new alc1220_fixup_gb_x570() is believed to also work for other boards,
like the Gigabyte X570 Aorus Extreme and the newer Gigabyte Aorus X570S
Master. However, as there is no way for me to test these I initially only
enable this new behaviour for the mainboard I have which is the Gigabyte
X570(non-S) Aorus Master.
I tested this patch on the 5.15 branch as well as on master and it is
working well for me.
This patch adds another possible subsystem ID for the ALC287 used by
the Lenovo Yoga 15ITL5.
It uses the same initalization as the others.
This patch has been tested and works for my device.
In 'perf report', entering a recursive function from inside of itself
(either directly of indirectly through some other function) results in
calling symbol__annotate2 multiple() times, and freeing the whole
disassembly when exiting from the innermost instance.
The first issue causes the function's disassembly to be duplicated, and
the latter a heap use-after-free (and crash) when trying to access the
disassembly again.
I reproduced the bug on perf 5.11.22 (Ubuntu 20.04.3 LTS) and 5.16.rc8
with the following testcase (compile with gcc recursive.c -o recursive).
To reproduce:
- perf record ./recursive
- perf report
- enter fibonacci and annotate it
- move the cursor on one of the "callq fibonacci" instructions and press enter
- at this point there will be two copies of the function in the disassembly
- go back by pressing q, and perf will crash
This patch addresses the issue by annotating a function and freeing the
associated memory on exit only if no annotation is already present, so
that a recursive function is only annotated on entry.
Signed-off-by: Dario Petrillo <dario.pk1@gmail.com> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: stable@kernel.org Link: http://lore.kernel.org/lkml/20220109234441.325106-1-dario.pk1@gmail.com Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
An initialised kobject must be freed using kobject_put() to avoid
leaking associated resources (e.g. the object name).
Commit fe3c60684377 ("firmware: Fix a reference count leak.") "fixed"
the leak in the first error path of the file registration helper but
left the second one unchanged. This "fix" would however result in a NULL
pointer dereference due to the release function also removing the never
added entry from the fw_cfg_entry_cache list. This has now been
addressed.
Fix the remaining kobject leak by restoring the common error path and
adding the missing kobject_put().
Commit fe3c60684377 ("firmware: Fix a reference count leak.") "fixed"
a kobject leak in the file registration helper by properly calling
kobject_put() for the entry in case registration of the object fails
(e.g. due to a name collision).
This would however result in a NULL pointer dereference when the
release function tries to remove the never added entry from the
fw_cfg_entry_cache list.
Fix this by moving the list-removal out of the release function.
Note that the offending commit was one of the benign looking umn.edu
fixes which was reviewed but not reverted. [1][2]
Make sure to always NUL-terminate file names retrieved from the firmware
to avoid accessing data beyond the entry slab buffer and exposing it
through sysfs in case the firmware data is corrupt.
Fixes: 75f3e8e47f38 ("firmware: introduce sysfs driver for QEMU's fw_cfg device") Cc: stable@vger.kernel.org # 4.6 Cc: Gabriel Somlo <somlo@cmu.edu> Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20211201132528.30025-4-johan@kernel.org Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[200~raw_local_irq_restore() called with IRQs enabled
WARNING: CPU: 1 PID: 1206 at kernel/locking/irqflag-debug.c:10
warn_bogus_irq_restore+0x1d/0x20 kernel/locking/irqflag-debug.c:10
Hardware initialization for the rtl8188cu can run for as long as 350 ms,
and the routine may be called with interrupts disabled. To avoid locking
the machine for this long, the current routine saves the interrupt flags
and enables local interrupts. The problem is that it restores the flags
at the end without disabling local interrupts first.
This patch fixes commit a53268be0cb9 ("rtlwifi: rtl8192cu: Fix too long
disable of IRQs").
Reported-by: syzbot+cce1ee31614c171f5595@syzkaller.appspotmail.com Cc: stable@vger.kernel.org Fixes: a53268be0cb9 ("rtlwifi: rtl8192cu: Fix too long disable of IRQs") Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by: Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20211215171105.20623-1-Larry.Finger@lwfinger.net Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing bulk-endpoint max-packet sanity check to
uvc_video_start_transfer() to avoid division by zero in
uvc_alloc_urb_buffers() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: c0efd232929c ("V4L/DVB (8145a): USB Video Class driver") Cc: stable@vger.kernel.org # 2.6.26 Signed-off-by: Johan Hovold <johan@kernel.org> Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The vga16fb framebuffer driver only supports Enhanced Graphics Adapter
(EGA) and Video Graphics Array (VGA) 16 color graphic cards.
But it doesn't check if the adapter is one of those or if a VGA16 mode
is used. This means that the driver will be probed even if a VESA BIOS
Extensions (VBE) or Graphics Output Protocol (GOP) interface is used.
This issue has been present for a long time but it was only exposed by
commit d391c5827107 ("drivers/firmware: move x86 Generic System
Framebuffers support") since the platform device registration to match
the {vesa,efi}fb drivers is done later as a consequence of that change.
All non-x86 architectures though treat orig_video_isVGA as a boolean so
only do the supported video mode check for x86 and not for other arches.
Reading from a file that was just extended by a write, but the write had
not yet reached the server would return ENODATA as illustrated by this
command:
$ xfs_io -c 'open -ft test' -c 'w 4096 1000' -c 'r 0 1000'
wrote 1000/1000 bytes at offset 4096
1000.000000 bytes, 1 ops; 0.0001 sec (5.610 MiB/sec and 5882.3529 ops/sec)
pread: No data available
Fix this case by having netfs assume zeroes when reads from server come
short like AFS and CEPH do
Link: https://lkml.kernel.org/r/20220110111444.926753-1-asmadeus@codewreck.org Cc: stable@vger.kernel.org Fixes: eb497943fa21 ("9p: Convert to using the netfs helper lib to do reads and caching") Co-authored-by: David Howells <dhowells@redhat.com> Reviewed-by: David Howells <dhowells@redhat.com> Tested-by: David Howells <dhowells@redhat.com> Signed-off-by: Dominique Martinet <asmadeus@codewreck.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 9P2000.L setattr method v9fs_vfs_setattr_dotl() copies struct iattr
values without checking whether they are valid causing unitialized
values to be copied. The 9P2000 setattr method v9fs_vfs_setattr() method
gets this right. Check whether struct iattr fields are valid first
before copying in v9fs_vfs_setattr_dotl() too and make sure that all
other fields are set to 0 apart from {g,u}id which should be set to
INVALID_{G,U}ID. This ensure that they can be safely sent over the wire
or printed for debugging later on.
Link: https://lkml.kernel.org/r/20211129114434.3637938-1-brauner@kernel.org Link: https://lkml.kernel.org/r/000000000000a0d53f05d1c72a4c%40google.com Cc: Eric Van Hensbergen <ericvh@gmail.com> Cc: Latchesar Ionkov <lucho@ionkov.net> Cc: Dominique Martinet <asmadeus@codewreck.org> Cc: stable@kernel.org Cc: v9fs-developer@lists.sourceforge.net Reported-by: syzbot+dfac92a50024b54acaa4@syzkaller.appspotmail.com Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
[Dominique: do not set a/mtime with just ATTR_A/MTIME as discussed] Signed-off-by: Dominique Martinet <asmadeus@codewreck.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Linux NFS server currently responds to a zero-length NFSv3 WRITE
request with NFS3ERR_IO. It responds to a zero-length NFSv4 WRITE
with NFS4_OK and count of zero.
RFC 1813 says of the WRITE procedure's @count argument:
count
The number of bytes of data to be written. If count is
0, the WRITE will succeed and return a count of 0,
barring errors due to permissions checking.
RFC 8881 has similar language for NFSv4, though NFSv4 removed the
explicit @count argument because that value is already contained in
the opaque payload array.
The synthetic client pynfs's WRT4 and WRT15 tests do emit zero-
length WRITEs to exercise this spec requirement. Commit fdec6114ee1f
("nfsd4: zero-length WRITE should succeed") addressed the same
problem there with the same fix.
But interestingly the Linux NFS client does not appear to emit zero-
length WRITEs, instead squelching them. I'm not aware of a test that
can generate such WRITEs for NFSv3, so I wrote a naive C program to
generate a zero-length WRITE and test this fix.
Fixes: 8154ef2776aa ("NFSD: Clean up legacy NFS WRITE argument XDR decoders") Reported-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Cc: stable@vger.kernel.org Signed-off-by: Chuck Lever <chuck.lever@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With KVM_CAP_S390_USER_SIGP, there are only five Signal Processor
orders (CONDITIONAL EMERGENCY SIGNAL, EMERGENCY SIGNAL, EXTERNAL CALL,
SENSE, and SENSE RUNNING STATUS) which are intended for frequent use
and thus are processed in-kernel. The remainder are sent to userspace
with the KVM_CAP_S390_USER_SIGP capability. Of those, three orders
(RESTART, STOP, and STOP AND STORE STATUS) have the potential to
inject work back into the kernel, and thus are asynchronous.
Let's look for those pending IRQs when processing one of the in-kernel
SIGP orders, and return BUSY (CC2) if one is in process. This is in
agreement with the Principles of Operation, which states that only one
order can be "active" on a CPU at a time.
Cc: stable@vger.kernel.org Suggested-by: David Hildenbrand <david@redhat.com> Signed-off-by: Eric Farman <farman@linux.ibm.com> Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com> Acked-by: David Hildenbrand <david@redhat.com> Link: https://lore.kernel.org/r/20211213210550.856213-2-farman@linux.ibm.com
[borntraeger@linux.ibm.com: add stable tag] Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Override the Processor Trace (PT) interrupt handler for guest mode if and
only if PT is configured for host+guest mode, i.e. is being used
independently by both host and guest. If PT is configured for system
mode, the host fully controls PT and must handle all events.
Fixes: 8479e04e7d6b ("KVM: x86: Inject PMI for KVM guest") Reported-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> Reported-by: Artem Kashkanov <artem.kashkanov@intel.com> Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211111020738.2512932-4-seanjc@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Wait to register perf callbacks until after doing vendor hardaware setup.
VMX's hardware_setup() configures Intel Processor Trace (PT) mode, and a
future fix to register the Intel PT guest interrupt hook if and only if
Intel PT is exposed to the guest will consume the configured PT mode.
Delaying registration to hardware setup is effectively a nop as KVM's perf
hooks all pivot on the per-CPU current_vcpu, which is non-NULL only when
KVM is handling an IRQ/NMI in a VM-Exit path. I.e. current_vcpu will be
NULL throughout both kvm_arch_init() and kvm_arch_hardware_setup().
Signed-off-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20211111020738.2512932-3-seanjc@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Protect perf_guest_cbs with RCU to fix multiple possible errors. Luckily,
all paths that read perf_guest_cbs already require RCU protection, e.g. to
protect the callback chains, so only the direct perf_guest_cbs touchpoints
need to be modified.
Bug #1 is a simple lack of WRITE_ONCE/READ_ONCE behavior to ensure
perf_guest_cbs isn't reloaded between a !NULL check and a dereference.
Fixed via the READ_ONCE() in rcu_dereference().
Bug #2 is that on weakly-ordered architectures, updates to the callbacks
themselves are not guaranteed to be visible before the pointer is made
visible to readers. Fixed by the smp_store_release() in
rcu_assign_pointer() when the new pointer is non-NULL.
Bug #3 is that, because the callbacks are global, it's possible for
readers to run in parallel with an unregisters, and thus a module
implementing the callbacks can be unloaded while readers are in flight,
resulting in a use-after-free. Fixed by a synchronize_rcu() call when
unregistering callbacks.
Bug #1 escaped notice because it's extremely unlikely a compiler will
reload perf_guest_cbs in this sequence. perf_guest_cbs does get reloaded
for future derefs, e.g. for ->is_user_mode(), but the ->is_in_guest()
guard all but guarantees the consumer will win the race, e.g. to nullify
perf_guest_cbs, KVM has to completely exit the guest and teardown down
all VMs before KVM start its module unload / unregister sequence. This
also makes it all but impossible to encounter bug #3.
Bug #2 has not been a problem because all architectures that register
callbacks are strongly ordered and/or have a static set of callbacks.
But with help, unloading kvm_intel can trigger bug #1 e.g. wrapping
perf_guest_cbs with READ_ONCE in perf_misc_flags() while spamming
kvm_intel module load/unload leads to:
The "PAGE_SIZE - 2 - size" calculation in legacy_parse_param() is an
unsigned type so a large value of "size" results in a high positive
value instead of a negative value as expected. Fix this by getting rid
of the subtraction.
Signed-off-by: Jamie Hill-Daniel <jamie@hill-daniel.co.uk> Signed-off-by: William Liu <willsroot@protonmail.com> Tested-by: Salvatore Bonaccorso <carnil@debian.org> Tested-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Acked-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the string passed into qcom_pil_info_store() isn't as long as
PIL_RELOC_NAME_LEN we'll try to copy the string assuming the length is
PIL_RELOC_NAME_LEN to the io space and go beyond the bounds of the
string. Let's only copy as many byes as the string is long, ignoring the
NUL terminator.
This fixes the following KASAN error:
BUG: KASAN: global-out-of-bounds in __memcpy_toio+0x124/0x140
Read of size 1 at addr ffffffd35086e386 by task rmtfs/2392
'buffer_index_array' really looks like a bitmap. So it should be allocated
as such.
When kzalloc is called, a number of bytes is expected, but a number of
longs is passed instead.
In get(), if not enough memory is allocated, un-allocated memory may be
read or written.
So use bitmap_zalloc() to safely allocate the correct memory size and
avoid un-expected behavior.
While at it, change the corresponding kfree() into bitmap_free() to keep
the semantic.
When UBSAN is enabled a case is shown on unplugging the display that
this variable hasn't been initialized by `update_dsc_caps`, presumably
when the display was unplugged it wasn't copied from the DPCD.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1956497 Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to Linux v5.4 devtmpfs used mount_single() which treats the given
mount options as "remount" options, so it updates the configuration of
the single super_block on each mount.
Since that was changed, the mount options used for devtmpfs are ignored.
This is a regression which affect systemd - which mounts devtmpfs with
"-o mode=755,size=4m,nr_inodes=1m".
This patch restores the "remount" effect by calling reconfigure_single()
Fixes: d401727ea0d7 ("devtmpfs: don't mix {ramfs,shmem}_fill_super() with mount_single()") Acked-by: Christian Brauner <christian.brauner@ubuntu.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: NeilBrown <neilb@suse.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The definitions for pdc_toc_pim_11 and pdc_toc_pim_20 are wrong since they
include an entry for a hversion field which doesn't exist in the specification.
Fix this and clean up some whitespaces so that the whole file will be in
sync with it's copy in the SeaBIOS-hppa sources.
clang warns about excessive stack usage in this driver when
UBSAN is enabled:
drivers/staging/greybus/audio_topology.c:977:12: error: stack frame size of 1836 bytes in function 'gbaudio_tplg_create_widget' [-Werror,-Wframe-larger-than=]
Rework this code to no longer use compound literals for
initializing the structure in each case, but instead keep
the common bits in a preallocated constant array and copy
them as needed.
A new warning in clang points out a place in this file where a bitwise
OR is being used with boolean types:
drivers/gpu/drm/i915/intel_pm.c:3066:12: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
changed = ilk_increase_wm_latency(dev_priv, dev_priv->wm.pri_latency, 12) |
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
This construct is intentional, as it allows every one of the calls to
ilk_increase_wm_latency() to occur (instead of short circuiting with
logical OR) while still caring about the result of each call.
To make this clearer to the compiler, use the '|=' operator to assign
the result of each ilk_increase_wm_latency() call to changed, which
keeps the meaning of the code the same but makes it obvious that every
one of these calls is expected to happen.
A lot of userspace depends on a descriptive name for vdev. Without this
patch, users have a hard time figuring out which camera shall they use
for their video conferencing.
Currently, if CONFIG_RANDOM_TRUST_BOOTLOADER is enabled, multiple calls
to add_bootloader_randomness() are broken and can cause a NULL pointer
dereference, as noted by Ivan T. Ivanov. This is not only a hypothetical
problem, as qemu on arm64 may provide bootloader entropy via EFI and via
devicetree.
On the first call to add_hwgenerator_randomness(), crng_fast_load() is
executed, and if the seed is long enough, crng_init will be set to 1.
On subsequent calls to add_bootloader_randomness() and then to
add_hwgenerator_randomness(), crng_fast_load() will be skipped. Instead,
wait_event_interruptible() and then credit_entropy_bits() will be called.
If the entropy count for that second seed is large enough, that proceeds
to crng_reseed().
However, both wait_event_interruptible() and crng_reseed() depends
(at least in numa_crng_init()) on workqueues. Therefore, test whether
system_wq is already initialized, which is a sufficient indicator that
workqueue_init_early() has progressed far enough.
If we wind up hitting the !system_wq case, we later want to do what
would have been done there when wqs are up, so set a flag, and do that
work later from the rand_initialize() call.
Reported-by: Ivan T. Ivanov <iivanov@suse.de> Fixes: 18b915ac6b0a ("efi/random: Treat EFI_RNG_PROTOCOL output as bootloader randomness") Cc: stable@vger.kernel.org Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
[Jason: added crng_need_done state and related logic.] Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_extract_crng() does plain loads of crng->init_time and
crng_global_init_time, which causes undefined behavior if
crng_reseed() and RNDRESEEDCRNG modify these corrently.
Use READ_ONCE() and WRITE_ONCE() to make the behavior defined.
Don't fix the race on crng->init_time by protecting it with crng->lock,
since it's not a problem for duplicate reseedings to occur. I.e., the
lockless access with READ_ONCE() is fine.
Fixes: d848e5f8e1eb ("random: add new ioctl RNDRESEEDCRNG") Fixes: e192be9d9a30 ("random: replace non-blocking pool with a Chacha20-based CRNG") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
extract_crng() and crng_backtrack_protect() load crng_node_pool with a
plain load, which causes undefined behavior if do_numa_crng_init()
modifies it concurrently.
Fix this by using READ_ONCE(). Note: as per the previous discussion
https://lore.kernel.org/lkml/20211219025139.31085-1-ebiggers@kernel.org/T/#u,
READ_ONCE() is believed to be sufficient here, and it was requested that
it be used here instead of smp_load_acquire().
Also change do_numa_crng_init() to set crng_node_pool using
cmpxchg_release() instead of mb() + cmpxchg(), as the former is
sufficient here but is more lightweight.
Fixes: 1e7f583af67b ("random: make /dev/urandom scalable for silly userspace programs") Cc: stable@vger.kernel.org Signed-off-by: Eric Biggers <ebiggers@google.com> Acked-by: Paul E. McKenney <paulmck@kernel.org> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No information is deliberately sent in hf->flags in host -> device
communications, but the open-source candleLight firmware echoes it
back, which can result in the GS_CAN_FLAG_OVERFLOW flag being set and
generating spurious ERRORFRAMEs.
While there also initialize the reserved member with 0.
In isotp_rcv_ff() 32 bit of data received over the network is assigned
to struct tpcon::len. Later in that function the length is checked for
the maximal supported length against MAX_MSG_LENGTH.
As struct tpcon::len is an "int" this check does not work, if the
provided length overflows the "int".
Later on struct tpcon::idx is compared against struct tpcon::len.
To fix this problem this patch converts both struct tpcon::{idx,len}
to unsigned int.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/all/20220105132429.1170627-1-mkl@pengutronix.de Cc: stable@vger.kernel.org Acked-by: Oliver Hartkopp <socketcan@hartkopp.net> Reported-by: syzbot+4c63f36709a642f801c5@syzkaller.appspotmail.com Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The received data contains the channel the received data is associated
with. If the channel number is bigger than the actual number of
channels assume broken or malicious USB device and shut it down.
This fixes the error found by clang:
| drivers/net/can/usb/gs_usb.c:386:6: error: variable 'dev' is used
| uninitialized whenever 'if' condition is true
| if (hf->channel >= GS_MAX_INTF)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
| drivers/net/can/usb/gs_usb.c:474:10: note: uninitialized use occurs here
| hf, dev->gs_hf_size, gs_usb_receive_bulk_callback,
| ^~~
Link: https://lore.kernel.org/all/20211210091158.408326-1-mkl@pengutronix.de Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices") Cc: stable@vger.kernel.org Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is found in the MacBookPro16,2, and as the MacBookPro16,1 is
from the same generation of MacBooks and has a UART with bxt_uart_info,
it was incorrectly assumed that the MacBookPro16,2's UART would have the
same info.
This led to the wrong clock speed being used, and the Bluetooth
controller exposed by the UART receiving and sending random data, which
was incorrectly assumed to be an issue with the Bluetooth stuff, not an
error with the UART side of things.
Changing the info to spt_uart_info changes the clock speed and makes it
send and receive data correctly.
Fixes: ddb1ada416fd ("mfd: intel-lpss: Add support for MacBookPro16,2 ICL-N UART") Signed-off-by: Orlando Chamberlain <redecorating@protonmail.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Cc: Aditya Garg <gargaditya08@live.com> Link: https://lore.kernel.org/r/20211124091846.11114-1-redecorating@protonmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The runtime PM callback may be called as soon as the runtime PM facility
is enabled and activated. It means that ->suspend() may be called before
we finish probing the device in the ACPI case. Hence, NULL pointer
dereference:
intel-lpss INT34BA:00: IRQ index 0 not found
BUG: kernel NULL pointer dereference, address: 0000000000000030
...
Workqueue: pm pm_runtime_work
RIP: 0010:intel_lpss_suspend+0xb/0x40 [intel_lpss]
To fix this, first try to register the device and only after that enable
runtime PM facility.
Fixes: 4b45efe85263 ("mfd: Add support for Intel Sunrisepoint LPSS devices") Reported-by: Orlando Chamberlain <redecorating@protonmail.com> Reported-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Aditya Garg <gargaditya08@live.com> Signed-off-by: Lee Jones <lee.jones@linaro.org> Link: https://lore.kernel.org/r/20211101190008.86473-1-andriy.shevchenko@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent reported that they have seen a significant amount of TCP retransmissions
at high throughput from applications residing in network namespaces talking to
the outside world via veths. The drops were seen on the qdisc layer (fq_codel,
as per systemd default) of the phys device such as ena or virtio_net due to all
traffic hitting a _single_ TX queue _despite_ multi-queue device. (Note that the
setup was _not_ using XDP on veths as the issue is generic.)
More specifically, after edbea9220251 ("veth: Store queue_mapping independently
of XDP prog presence") which made it all the way back to v4.19.184+,
skb_record_rx_queue() would set skb->queue_mapping to 1 (given 1 RX and 1 TX
queue by default for veths) instead of leaving at 0.
This is eventually retained and callbacks like ena_select_queue() will also pick
single queue via netdev_core_pick_tx()'s ndo_select_queue() once all the traffic
is forwarded to that device via upper stack or other means. Similarly, for others
not implementing ndo_select_queue() if XPS is disabled, netdev_pick_tx() might
call into the skb_tx_hash() and check for prior skb_rx_queue_recorded() as well.
In general, it is a _bad_ idea for virtual devices like veth to mess around with
queue selection [by default]. Given dev->real_num_tx_queues is by default 1,
the skb->queue_mapping was left untouched, and so prior to edbea9220251 the
netdev_core_pick_tx() could do its job upon __dev_queue_xmit() on the phys device.
Unbreak this and restore prior behavior by removing the skb_record_rx_queue()
from veth_xmit() altogether.
If the veth peer has an XDP program attached, then it would return the first RX
queue index in xdp_md->rx_queue_index (unless configured in non-default manner).
However, this is still better than breaking the generic case.
Fixes: edbea9220251 ("veth: Store queue_mapping independently of XDP prog presence") Fixes: 638264dc9022 ("veth: Support per queue XDP ring") Reported-by: Laurent Bernaille <laurent.bernaille@datadoghq.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Cc: Maciej Fijalkowski <maciej.fijalkowski@intel.com> Cc: Toshiaki Makita <toshiaki.makita1@gmail.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: Paolo Abeni <pabeni@redhat.com> Cc: John Fastabend <john.fastabend@gmail.com> Cc: Willem de Bruijn <willemb@google.com> Acked-by: John Fastabend <john.fastabend@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices have a bug causing them to not work if they query
LE tx power on startup. Thus we add a quirk in order to not query it
and default min/max tx power values to HCI_TX_POWER_INVALID.
If cfg80211 is providing extraie's for a scanning process then ath11k will
copy that over to the firmware. The extraie.len is a 32 bit value in struct
element_info and describes the amount of bytes for the vendor information
elements.
The WMI_TLV packet is having a special WMI_TAG_ARRAY_BYTE section. This
section can have a (payload) length up to 65535 bytes because the
WMI_TLV_LEN can store up to 16 bits. The code was missing such a check and
could have created a scan request which cannot be parsed correctly by the
firmware.
But the bigger problem was the allocation of the buffer. It has to align
the TLV sections by 4 bytes. But the code was using an u8 to store the
newly calculated length of this section (with alignment). And the new
calculated length was then used to allocate the skbuff. But the actual code
to copy in the data is using the extraie.len and not the calculated
"aligned" length.
The length of extraie with IEEE80211_HW_SINGLE_SCAN_ON_ALL_BANDS enabled
was 264 bytes during tests with a QCA Milan card. But it only allocated 8
bytes (264 bytes % 256) for it. As consequence, the code to memcpy the
extraie into the skb was then just overwriting data after skb->end. Things
like shinfo were therefore corrupted. This could usually be seen by a crash
in skb_zcopy_clear which tried to call a ubuf_info callback (using a bogus
address).
When the USB core code for getting root-hub status reports was
originally written, it was assumed that the hub driver would be its
only caller. But this isn't true now; user programs can use usbfs to
communicate with root hubs and get status reports. When they do this,
they may use a transfer_buffer that is smaller than the data returned
by the HCD, which will lead to a buffer overflow error when
usb_hcd_poll_rh_status() tries to store the status data. This was
discovered by syzbot:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: slab-out-of-bounds in usb_hcd_poll_rh_status+0x5f4/0x780 drivers/usb/core/hcd.c:776
Write of size 2 at addr ffff88801da403c0 by task syz-executor133/4062
This patch fixes the bug by reducing the amount of status data if it
won't fit in the transfer_buffer. If some data gets discarded then
the URB's completion status is set to -EOVERFLOW rather than 0, to let
the user know what happened.
Bugzilla #213839 reports a 7-port hub that doesn't work properly when
devices are plugged into some of the ports; the kernel goes into an
unending disconnect/reinitialize loop as shown in the bug report.
This "7-port hub" comprises two four-port hubs with one plugged into
the other; the failures occur when a device is plugged into one of the
downstream hub's ports. (These hubs have other problems too. For
example, they bill themselves as USB-2.0 compliant but they only run
at full speed.)
It turns out that the failures are caused by bugs in both the kernel
and the hub. The hub's bug is that it reports a different
bmAttributes value in its configuration descriptor following a remote
wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has
changed).
The kernel's bug is inside the hub driver's resume handler. When
hub_activate() sees that one of the hub's downstream ports got a
wakeup request from a child device, it notes this fact by setting the
corresponding bit in the hub->change_bits variable. But this variable
is meant for connection changes, not wakeup events; setting it causes
the driver to believe the downstream port has been disconnected and
then connected again (in addition to having received a wakeup
request).
Because of this, the hub driver then tries to check whether the device
currently plugged into the downstream port is the same as the device
that had been attached there before. Normally this check succeeds and
wakeup handling continues with no harm done (which is why the bug
remained undetected until now). But with these dodgy hubs, the check
fails because the config descriptor has changed. This causes the hub
driver to reinitialize the child device, leading to the
disconnect/reinitialize loop described in the bug report.
The proper way to note reception of a downstream wakeup request is
to set a bit in the hub->event_bits variable instead of
hub->change_bits. That way the hub driver will realize that something
has happened to the port but will not think the port and child device
have been disconnected. This patch makes that change.
Cc: <stable@vger.kernel.org> Tested-by: Jonathan McDowell <noodles@earth.li> Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/YdCw7nSfWYPKWQoD@rowland.harvard.edu Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reset GPIO was marked active-high, which is against what's specified
in the documentation. Mark the reset GPIO as active-low. With this
change, Bluetooth can now be used on the i9100.
Fixes: 8620cc2f99b7 ("ARM: dts: exynos: Add devicetree file for the Galaxy S2") Cc: stable@vger.kernel.org Signed-off-by: Paul Cercueil <paul@crapouillou.net> Link: https://lore.kernel.org/r/20211031234137.87070-1-paul@crapouillou.net Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing bulk-out endpoint sanity check to probe() to avoid
division by zero in bfusb_send_frame() in case a malicious device has
broken descriptors (or when doing descriptor fuzz testing).
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4fb0 ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
This patch fixes the broken LED quirk for Intel legacy ROM devices.
To fix the LED issue that doesn't turn off immediately, the host sends
the SW RFKILL command while shutting down the interface and it puts the
devices in SW RFKILL state.
Once the device is in SW RFKILL state, it can only accept HCI_Reset to
exit from the SW RFKILL state. This patch checks the quirk for broken
LED and sends the HCI_Reset before sending the HCI_Intel_Read_Version
command.
The affected legacy ROM devices are
- 8087:07dc
- 8087:0a2a
- 8087:0aa7
Fixes: ffcba827c0a1d ("Bluetooth: btintel: Fix the LED is not turning off immediately") Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While auditing some other code, I noticed missing checks inside the pointer
arithmetic simulation, more specifically, adjust_ptr_min_max_vals(). Several
*_OR_NULL types are not rejected whereas they are _required_ to be rejected
given the expectation is that they get promoted into a 'real' pointer type
for the success case, that is, after an explicit != NULL check.
One case which stands out and is accessible from unprivileged (iff enabled
given disabled by default) is BPF ring buffer. From crafting a PoC, the NULL
check can be bypassed through an offset, and its id marking will then lead
to promotion of mem_or_null to a mem type.
bpf_ringbuf_reserve() helper can trigger this case through passing of reserved
flags, for example.
from 8 to 13: safe
processed 15 insns (limit 1000000) max_states_per_insn 0 total_states 1 peak_states 1 mark_read 0
OK
All three commits, that is b121b341e598 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support"), 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it"), and the afbf21dce668 ("bpf: Support readonly/readwrite buffers in verifier") suffer the same
cause and their *_OR_NULL type pendants must be rejected in adjust_ptr_min_max_vals().
Make the test more robust by reusing reg_type_may_be_null() helper such that we catch
all *_OR_NULL types we have today and in future.
Note that pointer arithmetic on PTR_TO_BTF_ID, PTR_TO_RDONLY_BUF, and PTR_TO_RDWR_BUF
is generally allowed.
Fixes: b121b341e598 ("bpf: Add PTR_TO_BTF_ID_OR_NULL support") Fixes: 457f44363a88 ("bpf: Implement BPF ring buffer and verifier support for it") Fixes: afbf21dce668 ("bpf: Support readonly/readwrite buffers in verifier") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the driver is unloaded or when the system goes into standby mode,
DeInitLed871x is called to stop the led layer. In this case, we stop
the blinking worker but we do not switch the led off explicitly. On my
system, I can go into standby mode with the LED enabled.
Add a call to SwLedOff to fix this.
Fixes: 15865124feed ("staging: r8188eu: introduce new core dir for RTL8188eu driver") Cc: stable@vger.kernel.org Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20211226195556.159471-2-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At CPU-hotplug time, unbind_workers() may preempt a worker while it is
going to sleep. In that case the following scenario can happen:
unbind_workers() wq_worker_sleeping()
-------------- -------------------
if (worker->flags & WORKER_NOT_RUNNING)
return;
//PREEMPTED by unbind_workers
worker->flags |= WORKER_UNBOUND;
[...]
atomic_set(&pool->nr_running, 0);
//resume to worker
atomic_dec_and_test(&pool->nr_running);
After unbind_worker() resets pool->nr_running, the value is expected to
remain 0 until the pool ever gets rebound in case cpu_up() is called on
the target CPU in the future. But here the race leaves pool->nr_running
with a value of -1, triggering the following warning when the worker goes
idle:
Also due to this incorrect "nr_running == -1", all sorts of hazards can
happen, starting with queued works being ignored because no workers are
awaken at insert_work() time.
Fix this with checking again the worker flags while pool->lock is locked.
Fixes: b945efcdd07d ("sched: Remove pointless preemption disable in sched_submit_work()") Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com> Tested-by: Paul E. McKenney <paulmck@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Paul E. McKenney <paulmck@kernel.org> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Daniel Bristot de Oliveira <bristot@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At CPU-hotplug time, unbind_worker() may preempt a worker while it is
waking up. In that case the following scenario can happen:
unbind_workers() wq_worker_running()
-------------- -------------------
if (!(worker->flags & WORKER_NOT_RUNNING))
//PREEMPTED by unbind_workers
worker->flags |= WORKER_UNBOUND;
[...]
atomic_set(&pool->nr_running, 0);
//resume to worker
atomic_inc(&worker->pool->nr_running);
After unbind_worker() resets pool->nr_running, the value is expected to
remain 0 until the pool ever gets rebound in case cpu_up() is called on
the target CPU in the future. But here the race leaves pool->nr_running
with a value of 1, triggering the following warning when the worker goes
idle:
Also due to this incorrect "nr_running == 1", further queued work may
end up not being served, because no worker is awaken at work insert time.
This raises rcutorture writer stalls for example.
Fix this with disabling preemption in the right place in
wq_worker_running().
It's worth noting that if the worker migrates and runs concurrently with
unbind_workers(), it is guaranteed to see the WORKER_UNBOUND flag update
due to set_cpus_allowed_ptr() acquiring/releasing rq->lock.
Fixes: 6d25be5782e4 ("sched/core, workqueues: Distangle worker accounting from rq lock") Reviewed-by: Lai Jiangshan <jiangshanlai@gmail.com> Tested-by: Paul E. McKenney <paulmck@kernel.org> Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Frederic Weisbecker <frederic@kernel.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Cc: Daniel Bristot de Oliveira <bristot@redhat.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 9 Jan 2022 18:49:12 +0000 (10:49 -0800)]
Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"A small fixup to the Zinitix touchscreen driver to avoid enabling the
IRQ line before we successfully requested it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: zinitix - make sure the IRQ is allocated before it gets enabled
Linus Torvalds [Sun, 9 Jan 2022 18:43:16 +0000 (10:43 -0800)]
Merge tag 'soc-fixes-5.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fix from Olof Johansson:
"One more fix for 5.16
I had missed one patch when I sent up what I thought was the last
batch of fixes for this release. This one fixes issues on the
Raspberry Pi platforms due to gpio init changes this release, so
hopefully we can get it merged before final release is cut"
* tag 'soc-fixes-5.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: gpio-ranges property is now required
Linus Torvalds [Sun, 9 Jan 2022 18:37:07 +0000 (10:37 -0800)]
Merge tag 'perf-tools-fixes-for-v5.16-2022-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Revert "libtraceevent: Increase libtraceevent logging when verbose",
breaks the build with libtraceevent-1.3.0, i.e. when building with
'LIBTRACEEVENT_DYNAMIC=1'.
- Avoid early exit in 'perf trace' due to running SIGCHLD handler
before it makes sense to. It can happen when using a BPF source code
event that have to be first built into an object file.
* tag 'perf-tools-fixes-for-v5.16-2022-01-09' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
Revert "libtraceevent: Increase libtraceevent logging when verbose"
perf trace: Avoid early exit due to running SIGCHLD handler before it makes sense to
Nikita Travkin [Sun, 9 Jan 2022 07:19:19 +0000 (23:19 -0800)]
Input: zinitix - make sure the IRQ is allocated before it gets enabled
Since irq request is the last thing in the driver probe, it happens
later than the input device registration. This means that there is a
small time window where if the open method is called the driver will
attempt to enable not yet available irq.
Fix that by moving the irq request before the input device registration.
Phil Elwell [Tue, 4 Jan 2022 17:02:47 +0000 (18:02 +0100)]
ARM: dts: gpio-ranges property is now required
Since [1], added in 5.7, the absence of a gpio-ranges property has
prevented GPIOs from being restored to inputs when released.
Add those properties for BCM283x and BCM2711 devices.
[1] commit 2ab73c6d8323 ("gpio: Support GPIO controllers without
pin-ranges")
Link: https://lore.kernel.org/r/20220104170247.956760-1-linus.walleij@linaro.org Fixes: 2ab73c6d8323 ("gpio: Support GPIO controllers without pin-ranges") Fixes: 266423e60ea1 ("pinctrl: bcm2835: Change init order for gpio hogs") Reported-by: Stefan Wahren <stefan.wahren@i2se.com> Reported-by: Florian Fainelli <f.fainelli@gmail.com> Reported-by: Jan Kiszka <jan.kiszka@web.de> Signed-off-by: Phil Elwell <phil@raspberrypi.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20211206092237.4105895-3-phil@raspberrypi.com Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>
Linus Torvalds [Sat, 8 Jan 2022 20:12:58 +0000 (12:12 -0800)]
Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Fix the regression with AMD GPU suspend by reverting the
handling of bus regulators in the I2C core.
Also, there is a fix for the MPC driver to prevent an
out-of-bound-access"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
Revert "i2c: core: support bus regulator controlling in adapter"
i2c: mpc: Avoid out of bounds memory access
Linus Torvalds [Sat, 8 Jan 2022 19:39:53 +0000 (11:39 -0800)]
Merge tag 'for-v5.16-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
"Three fixes for the 5.16 cycle:
- Avoid going beyond last capacity in the power-supply core
- Replace 1E6L with NSEC_PER_MSEC to avoid floating point calculation
in LLVM resulting in a build failure
- Fix ADC measurements in bq25890 charger driver"
* tag 'for-v5.16-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: reset: ltc2952: Fix use of floating point literals
power: bq25890: Enable continuous conversion for ADC at charging
power: supply: core: Break capacity loop
Linus Torvalds [Fri, 7 Jan 2022 23:58:06 +0000 (15:58 -0800)]
Merge branch 'for-5.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup fixes from Tejun Heo:
"This contains the cgroup.procs permission check fixes so that they use
the credentials at the time of open rather than write, which also
fixes the cgroup namespace lifetime bug"
* 'for-5.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
selftests: cgroup: Test open-time cgroup namespace usage for migration checks
selftests: cgroup: Test open-time credential usage for migration checks
selftests: cgroup: Make cg_create() use 0755 for permission instead of 0644
cgroup: Use open-time cgroup namespace for process migration perm checks
cgroup: Allocate cgroup_file_ctx for kernfs_open_file->priv
cgroup: Use open-time credentials for process migraton perm checks
Wolfram Sang [Thu, 6 Jan 2022 12:24:52 +0000 (13:24 +0100)]
Revert "i2c: core: support bus regulator controlling in adapter"
This largely reverts commit 5a7b95fb993ec399c8a685552aa6a8fc995c40bd. It
breaks suspend with AMD GPUs, and we couldn't incrementally fix it. So,
let's remove the code and go back to the drawing board. We keep the
header extension to not break drivers already populating the regulator.
We expect to re-add the code handling it soon.
This breaks the build as it will prefer using libbpf-devel header files,
even when not using LIBBPF_DYNAMIC=1, breaking the build.
This was detected on OpenSuSE Tumbleweed with libtraceevent-devel 1.3.0,
as described by Jiri Slaby:
=======================================================================
It breaks build with LIBTRACEEVENT_DYNAMIC and version 1.3.0:
> util/debug.c: In function ‘perf_debug_option’:
> util/debug.c:243:17: error: implicit declaration of function
‘tep_set_loglevel’ [-Werror=implicit-function-declaration]
> 243 | tep_set_loglevel(TEP_LOG_INFO);
> | ^~~~~~~~~~~~~~~~
> util/debug.c:243:34: error: ‘TEP_LOG_INFO’ undeclared (first use in this
function); did you mean ‘TEP_PRINT_INFO’?
> 243 | tep_set_loglevel(TEP_LOG_INFO);
> | ^~~~~~~~~~~~
> | TEP_PRINT_INFO
> util/debug.c:243:34: note: each undeclared identifier is reported only once
for each function it appears in
> util/debug.c:245:34: error: ‘TEP_LOG_DEBUG’ undeclared (first use in this
function)
> 245 | tep_set_loglevel(TEP_LOG_DEBUG);
> | ^~~~~~~~~~~~~
> util/debug.c:247:34: error: ‘TEP_LOG_ALL’ undeclared (first use in this
function)
> 247 | tep_set_loglevel(TEP_LOG_ALL);
> | ^~~~~~~~~~~
It is because the gcc's command line looks like:
gcc
...
-I/home/abuild/rpmbuild/BUILD/tools/lib/
...
-DLIBTRACEEVENT_VERSION=65790
...
=======================================================================
The proper way to fix this is more involved and so not suitable for this
late in the 5.16-rc stage.
the event parsing eventually calls llvm__get_kbuild_opts() that runs a
script and that ends up with SIGCHLD delivered to the 'perf trace'
handler, which assumes the workload process is done and quits 'perf
trace'.
Move the SIGCHLD handler setup directly to trace__run(), where the event
is parsed and the object is already compiled.
Signed-off-by: Jiri Olsa <jolsa@kernel.org> Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Christy Lee <christyc.y.lee@gmail.com> Cc: Ian Rogers <irogers@google.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Petlan <mpetlan@redhat.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lore.kernel.org/lkml/20220106222030.227499-1-jolsa@kernel.org Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Linus Torvalds [Fri, 7 Jan 2022 17:17:53 +0000 (09:17 -0800)]
Merge tag 'drm-fixes-2022-01-07' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"There is only the amdgpu runtime pm regression fix in here:
amdgpu:
- suspend/resume fix
- fix runtime PM regression"
* tag 'drm-fixes-2022-01-07' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: disable runpm if we are the primary adapter
fbdev: fbmem: add a helper to determine if an aperture is used by a fw fb
drm/amd/pm: keep the BACO feature enabled for suspend
Linus Torvalds [Fri, 7 Jan 2022 02:35:17 +0000 (18:35 -0800)]
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma fixes from Jason Gunthorpe:
"Last pull for 5.16, the reversion has been known for a while now but
didn't get a proper fix in time. Looks like we will have several
info-leak bugs to take care of going foward.
- Revert the patch fixing the DM related crash causing a widespread
regression for kernel ULPs. A proper fix just didn't appear this
cycle due to the holidays
- Missing NULL check on alloc in uverbs
- Double free in rxe error paths
- Fix a new kernel-infoleak report when forming ah_attr's without
GRH's in ucma"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/core: Don't infoleak GRH fields
RDMA/uverbs: Check for null return of kmalloc_array
Revert "RDMA/mlx5: Fix releasing unallocated memory in dereg MR flow"
RDMA/rxe: Prevent double freeing rxe_map_set()
Linus Torvalds [Thu, 6 Jan 2022 23:00:43 +0000 (15:00 -0800)]
Merge tag 'trace-v5.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"Three minor tracing fixes:
- Fix missing prototypes in sample module for direct functions
- Fix check of valid buffer in get_trace_buf()
- Fix annotations of percpu pointers"
* tag 'trace-v5.16-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Tag trace_percpu_buffer as a percpu pointer
tracing: Fix check for trace_percpu_buffer validity in get_trace_buf()
ftrace/samples: Add missing prototypes direct functions
Tejun Heo [Thu, 6 Jan 2022 21:02:29 +0000 (11:02 -1000)]
cgroup: Use open-time cgroup namespace for process migration perm checks
cgroup process migration permission checks are performed at write time as
whether a given operation is allowed or not is dependent on the content of
the write - the PID. This currently uses current's cgroup namespace which is
a potential security weakness as it may allow scenarios where a less
privileged process tricks a more privileged one into writing into a fd that
it created.
This patch makes cgroup remember the cgroup namespace at the time of open
and uses it for migration permission checks instad of current's. Note that
this only applies to cgroup2 as cgroup1 doesn't have namespace support.
This also fixes a use-after-free bug on cgroupns reported in
Tejun Heo [Thu, 6 Jan 2022 21:02:29 +0000 (11:02 -1000)]
cgroup: Allocate cgroup_file_ctx for kernfs_open_file->priv
of->priv is currently used by each interface file implementation to store
private information. This patch collects the current two private data usages
into struct cgroup_file_ctx which is allocated and freed by the common path.
This allows generic private data which applies to multiple files, which will
be used to in the following patch.
Note that cgroup_procs iterator is now embedded as procs.iter in the new
cgroup_file_ctx so that it doesn't need to be allocated and freed
separately.
v2: union dropped from cgroup_file_ctx and the procs iterator is embedded in
cgroup_file_ctx as suggested by Linus.
v3: Michal pointed out that cgroup1's procs pidlist uses of->priv too.
Converted. Didn't change to embedded allocation as cgroup1 pidlists get
stored for caching.
Tejun Heo [Thu, 6 Jan 2022 21:02:28 +0000 (11:02 -1000)]
cgroup: Use open-time credentials for process migraton perm checks
cgroup process migration permission checks are performed at write time as
whether a given operation is allowed or not is dependent on the content of
the write - the PID. This currently uses current's credentials which is a
potential security weakness as it may allow scenarios where a less
privileged process tricks a more privileged one into writing into a fd that
it created.
This patch makes both cgroup2 and cgroup1 process migration interfaces to
use the credentials saved at the time of open (file->f_cred) instead of
current's.
Reported-by: "Eric W. Biederman" <ebiederm@xmission.com> Suggested-by: Linus Torvalds <torvalds@linuxfoundation.org> Fixes: 187fe84067bd ("cgroup: require write perm on common ancestor when moving processes on the default hierarchy") Reviewed-by: Michal Koutný <mkoutny@suse.com> Signed-off-by: Tejun Heo <tj@kernel.org>
This happened because we would overrun the i2c->msgs array on the final
interrupt for the I2C STOP. This didn't happen if the last message was a
read because there is no interrupt in that case. Ensure that we only
access the current message if we are not processing a I2C STOP
condition.
Fixes: 1538d82f4647 ("i2c: mpc: Interrupt driven transfer") Reported-by: Maxime Bizon <mbizon@freebox.fr> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Signed-off-by: Wolfram Sang <wsa@kernel.org>
Olof Johansson [Thu, 6 Jan 2022 00:18:44 +0000 (16:18 -0800)]
Merge tag 'socfpga_fix_for_v5.16_part_3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/fixes
SoCFPGA dts updates for v5.16, part 3
- Change the SoCFPGA compatible to "intel,socfpga-qspi"
- Update dt-bindings document to include "intel,socfpga-qspi"
* tag 'socfpga_fix_for_v5.16_part_3' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux: (361 commits)
ARM: dts: socfpga: change qspi to "intel,socfpga-qspi"
dt-bindings: spi: cadence-quadspi: document "intel,socfpga-qspi"
Linux 5.16-rc7
mm/hwpoison: clear MF_COUNT_INCREASED before retrying get_any_page()
mm/damon/dbgfs: protect targets destructions with kdamond_lock
mm/page_alloc: fix __alloc_size attribute for alloc_pages_exact_nid
mm: delete unsafe BUG from page_cache_add_speculative()
mm, hwpoison: fix condition in free hugetlb page path
MAINTAINERS: mark more list instances as moderated
kernel/crash_core: suppress unknown crashkernel parameter warning
mm: mempolicy: fix THP allocations escaping mempolicy restrictions
kfence: fix memory leak when cat kfence objects
platform/x86: intel_pmc_core: fix memleak on registration failure
net: stmmac: dwmac-visconti: Fix value of ETHER_CLK_SEL_FREQ_SEL_2P5M
r8152: sync ocp base
r8152: fix the force speed doesn't work for RTL8156
net: bridge: fix ioctl old_deviceless bridge argument
net: stmmac: ptp: fix potentially overflowing expression
net: dsa: tag_ocelot: use traffic class to map priority on injected header
veth: ensure skb entering GRO are not cloned.
...
projects / linux-stable / log