Update the comment about what happens when link goes down after we have
checked for link-up. If a PIO request is done while link-down, we have
a serious problem.
Callback for irq_mask_ack() is the same as for irq_mask(). As there is no
special handling for irq_ack(), there is no need to define irq_mask_ack()
too.
Link: https://lore.kernel.org/r/20220110015018.26359-20-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Marc Zyngier <maz@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Emulated root bridge currently provides only one Legacy INTA interrupt
which is used for reporting PCIe PME and ERR events and handled by kernel
PCIe PME and AER drivers.
Aardvark HW reports these PME and ERR events separately, so there is no
need to mix real INTA interrupt and emulated INTA interrupt for PCIe PME
and AER drivers.
Register a new advk-RP (as in Root Port) irq chip and a new irq domain
for emulated root bridge and use this new separate irq domain for
providing INTA interrupt from emulated root bridge for PME and ERR events.
The real INTA interrupt from real devices is now separate.
A custom map_irq callback function on PCI host bridge structure is used to
allocate IRQ mapping for emulated root bridge from new irq domain. Original
callback of_irq_parse_and_map_pci() is used for all other devices as before.
Link: https://lore.kernel.org/r/20220110015018.26359-19-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable aardvark PME interrupt unconditionally by unmasking it and read PME
requester ID to emulated bridge config space immediately after receiving
interrupt.
PME requester ID is stored in the PCIE_MSG_LOG_REG register, which contains
the last inbound message. So when new inbound message is received by HW
(including non-PM), the content in PCIE_MSG_LOG_REG register is replaced by
a new value.
PCIe specification mandates that subsequent PMEs are kept pending until the
PME Status Register bit is cleared by software by writing a 1b.
Support for masking/unmasking PME interrupt on emulated bridge via
PCI_EXP_RTCTL_PMEIE bit is now implemented only in emulated bridge config
space, to ensure that we do not miss any aardvark PME interrupt.
Reading of PCI_EXP_RTCAP and PCI_EXP_RTSTA registers is simplified as final
value is now always stored into emulated bridge config space by the
interrupt handler, so there is no need to implement support for these
registers in read_pcie callback.
Clearing of W1C bit PCI_EXP_RTSTA_PME is now also simplified as it is done
by pci-bridge-emul.c code for emulated bridge config space. So there is no
need to implement support for clearing this bit in write_pcie callback.
Link: https://lore.kernel.org/r/20220110015018.26359-18-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently enabling PCI_EXP_RTSTA_PME bit in PCI_EXP_RTCTL register does
nothing. This is because PCIe PME driver expects to receive PCIe interrupt
defined in PCI_EXP_FLAGS_IRQ register, but aardvark hardware does not
trigger PCIe INTx/MSI interrupt for PME event, rather it triggers custom
aardvark interrupt which this driver is not processing yet.
Fix this issue by handling PME interrupt in advk_pcie_handle_int() and
chaining it to PCIe interrupt 0 with generic_handle_domain_irq() (since
aardvark sets PCI_EXP_FLAGS_IRQ to zero). With this change PCIe PME driver
finally starts receiving PME interrupt.
Link: https://lore.kernel.org/r/20220110015018.26359-17-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To optimize advk_pci_bridge_emul_pcie_conf_write() code, touch
PCIE_ISR0_REG and PCIE_ISR0_MASK_REG registers only when it is really
needed, when processing PCI_EXP_RTCTL_PMEIE and PCI_EXP_RTSTA_PME bits.
Link: https://lore.kernel.org/r/20220110015018.26359-16-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ERR interrupt is triggered when corresponding bit is unmasked in both ISR0
and PCI_EXP_DEVCTL registers. Unmasking ERR bits in PCI_EXP_DEVCTL register
is not enough. This means that currently the ERR interrupt is never
triggered.
Unmask ERR bits in ISR0 register at driver probe time. ERR interrupt is not
triggered until ERR bits are unmasked also in PCI_EXP_DEVCTL register,
which is done by AER driver. So it is safe to unconditionally unmask all
ERR bits in aardvark probe.
Aardvark HW sets PCI_ERR_ROOT_AER_IRQ to zero and when corresponding bits
in ISR0 and PCI_EXP_DEVCTL are enabled, the HW triggers a generic interrupt
on GIC. Chain this interrupt to PCIe interrupt 0 with
generic_handle_domain_irq() to allow processing of ERR interrupts.
Link: https://lore.kernel.org/r/20220110015018.26359-14-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to PCI 3.0 specification, sending both MSI and MSI-X interrupts
is done by DWORD memory write operation to doorbell message address. The
write operation for MSI has zero upper 16 bits and the MSI interrupt number
in the lower 16 bits, while the write operation for MSI-X contains a 32-bit
value from MSI-X table.
Since the driver only uses interrupt numbers from range 0..31, the upper
16 bits of the DWORD memory write operation to doorbell message address
are zero even for MSI-X interrupts. Thus we can enable MSI-X interrupts.
Testing proves that kernel can correctly receive MSI-X interrupts from PCIe
cards which supports both MSI and MSI-X interrupts.
Link: https://lore.kernel.org/r/20220110015018.26359-13-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MSI address for receiving MSI interrupts needs to be correctly set before
enabling processing of MSI interrupts.
Move code for setting PCIE_MSI_ADDR_LOW_REG and PCIE_MSI_ADDR_HIGH_REG
from advk_pcie_init_msi_irq_domain() to advk_pcie_setup_hw(), before
enabling PCIE_CORE_CTRL2_MSI_ENABLE.
After this we can remove the now unused member msi_msg, which was used
only for MSI doorbell address. MSI address can be any address which cannot
be used to DMA to. So change it to the address of the main struct advk_pcie.
Link: https://lore.kernel.org/r/20220110015018.26359-12-kabel@kernel.org Fixes: 8c39d710363c ("PCI: aardvark: Add Aardvark PCI host controller driver") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Marc Zyngier <maz@kernel.org> Cc: stable@vger.kernel.org # f21a8b1b6837 ("PCI: aardvark: Move to MSI handling using generic MSI support") Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the masking of ISR0/1 Sources and unmasking of summary MSI interrupt
so that it corresponds to the comments:
- first mask all ISR0/1
- then unmask all MSIs
- then unmask summary MSI interrupt
Link: https://lore.kernel.org/r/20220110015018.26359-10-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use simple
dev_fwnode(dev)
instead of
struct device_node *node = dev->of_node;
of_node_to_fwnode(node)
especially since the node variable is not used elsewhere in the function.
Link: https://lore.kernel.org/r/20220110015018.26359-9-kabel@kernel.org Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In [1] it was agreed that we should use struct irq_chip as a global
static struct in the driver. Even though the structure currently
contains a dynamic member (parent_device), In [2] the plans to kill it
and make the structure completely static were set out.
Convert Aardvark's priv->msi_bottom_irq_chip and priv->msi_irq_chip to
static driver structure.
Rewrite the code to use irq_set_chained_handler_and_data() handler with
chained_irq_enter() and chained_irq_exit() processing instead of using
devm_request_irq().
advk_pcie_irq_handler() reads IRQ status bits and calls other functions
based on which bits are set. These functions then read its own IRQ status
bits and calls other aardvark functions based on these bits. Finally
generic_handle_domain_irq() with translated linux IRQ numbers are called.
Link: https://lore.kernel.org/r/20220110015018.26359-5-kabel@kernel.org Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Signed-off-by: Marek Behún <kabel@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SD spec definition:
"Host provides at least 74 Clocks before issuing first command"
After 1ms for the voltage stable then start issuing the Clock signals
if POWER STATE is
MMC_POWER_OFF to MMC_POWER_UP to issue Clock signal to card
MMC_POWER_UP to MMC_POWER_ON to stop issuing signal to card
Because mremap does not have a MAP_FIXED_NOREPLACE flag, it can destroy
existing mappings. This causes a segfault when regions such as text are
remapped and the permissions are changed.
Verify the requested mremap destination address does not overlap any
existing mappings by using mmap's MAP_FIXED_NOREPLACE flag. Keep
incrementing the destination address until a valid mapping is found or
fail the current test once the max address is reached.
Avoid calling mmap with requested addresses that are less than the
system's mmap_min_addr. When run as root, mmap returns EACCES when
trying to map addresses < mmap_min_addr. This is not one of the error
codes for the condition to retry the mmap in the test.
Rather than arbitrarily retrying on EACCES, don't attempt an mmap until
addr > vm.mmap_min_addr.
Add a munmap call after an alignment check as the mappings are retained
after the retry and can reach the vm.max_map_count sysctl.
As commit 0c5f81dad46 ("KVM: LAPIC: Inject timer interrupt via posted
interrupt") mentioned that the host admin should well tune the guest
setup, so that vCPUs are placed on isolated pCPUs, and with several pCPUs
surplus for *busy* housekeeping. In this setup, it is preferrable to
disable mwait/hlt/pause vmexits to keep the vCPUs in non-root mode.
However, if only some guests isolated and others not, they would not
have any benefit from posted timer interrupts, and at the same time lose
VMX preemption timer fast paths because kvm_can_post_timer_interrupt()
returns true and therefore forces kvm_can_use_hv_timer() to false.
By guaranteeing that posted-interrupt timer is only used if MWAIT or
HLT are done without vmexit, KVM can make a better choice and use the
VMX preemption timer and the corresponding fast paths.
Reported-by: Aili Yao <yaoaili@kingsoft.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Cc: Aili Yao <yaoaili@kingsoft.com> Cc: Sean Christopherson <seanjc@google.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1643112538-36743-1-git-send-email-wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
WARN and bail if KVM attempts to free a root that isn't backed by a shadow
page. KVM allocates a bare page for "special" roots, e.g. when using PAE
paging or shadowing 2/3/4-level page tables with 4/5-level, and so root_hpa
will be valid but won't be backed by a shadow page. It's all too easy to
blindly call mmu_free_root_page() on root_hpa, be nice and WARN instead of
crashing KVM and possibly the kernel.
Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Emulating writes to SELF_IPI with a write to ICR has an unwanted side effect:
the value of ICR in vAPIC page gets changed. The lists SELF_IPI as write-only,
with no associated MMIO offset, so any write should have no visible side
effect in the vAPIC page.
Reported-by: Chao Gao <chao.gao@intel.com> Reviewed-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
MSR_KVM_POLL_CONTROL is cleared on reset, thus reverting guests to
host-side polling after suspend/resume. Non-bootstrap CPUs are
restored correctly by the haltpoll driver because they are hot-unplugged
during suspend and hot-plugged during resume; however, the BSP
is not hotpluggable and remains in host-sde polling mode after
the guest resume. The makes the guest pay for the cost of vmexits
every time the guest enters idle.
Fix it by recording BSP's haltpoll state and resuming it during guest
resume.
Cc: Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1650267752-46796-1-git-send-email-wanpengli@tencent.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Populating memory : 0.684014577s
Writing to populated memory : 0.006230175s
Reading from populated memory : 0.004557805s
==== Test Assertion Failure ====
lib/kvm_util.c:1411: false
pid=125806 tid=125809 errno=4 - Interrupted system call
1 0x0000000000402f7c: addr_gpa2hva at kvm_util.c:1411
2 (inlined by) addr_gpa2hva at kvm_util.c:1405
3 0x0000000000401f52: lookup_pfn at access_tracking_perf_test.c:98
4 (inlined by) mark_vcpu_memory_idle at access_tracking_perf_test.c:152
5 (inlined by) vcpu_thread_main at access_tracking_perf_test.c:232
6 0x00007fefe9ff81ce: ?? ??:0
7 0x00007fefe9c64d82: ?? ??:0
No vm physical memory at 0xffbffff000
I can easily reproduce it with a Intel(R) Xeon(R) CPU E5-2630 with 46 bits
PA.
It turns out that the address translation for clearing idle page tracking
returned a wrong result; addr_gva2gpa()'s last step, which is based on
"pte[index[0]].pfn", did the calculation with 40 bits length and the
high 12 bits got truncated. In above case the GPA address to be returned
should be 0x3fffbffff000 for GVA 0xc0000000, but it got truncated into
0xffbffff000 and the subsequent gpa2hva lookup failed.
The width of operations on bit fields greater than 32-bit is
implementation defined, and differs between GCC (which uses the bitfield
precision) and clang (which uses 64-bit arithmetic), so this is a
potential minefield. Remove the bit fields and using manual masking
instead.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=2075036 Reported-by: Nana Liu <nanliu@redhat.com> Reviewed-by: Peter Xu <peterx@redhat.com> Tested-by: Peter Xu <peterx@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Exit to userspace with an emulation error if KVM encounters an injected
exception with invalid guest state, in addition to the existing check of
bailing if there's a pending exception (KVM doesn't support emulating
exceptions except when emulating real mode via vm86).
In theory, KVM should never get to such a situation as KVM is supposed to
exit to userspace before injecting an exception with invalid guest state.
But in practice, userspace can intervene and manually inject an exception
and/or stuff registers to force invalid guest state while a previously
injected exception is awaiting reinjection.
Fixes: fc4fad79fc3d ("KVM: VMX: Reject KVM_RUN if emulation is required with pending exception") Reported-by: syzbot+cfafed3bb76d3e37581b@syzkaller.appspotmail.com Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220502221850.131873-1-seanjc@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
svm_vm_migrate_from() uses sev_lock_vcpus_for_migration() to lock all
source and target vcpu->locks. Unfortunately there is an 8 subclass
limit, so a new subclass cannot be used for each vCPU. Instead maintain
ownership of the first vcpu's mutex.dep_map using a role specific
subclass: source vs target. Release the other vcpu's mutex.dep_maps.
Fixes: b56639318bb2b ("KVM: SEV: Add support for SEV intra host migration") Reported-by: John Sperbeck<jsperbeck@google.com> Suggested-by: David Rientjes <rientjes@google.com> Suggested-by: Sean Christopherson <seanjc@google.com> Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Cc: Hillf Danton <hdanton@sina.com> Cc: kvm@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: Peter Gonda <pgonda@google.com>
Message-Id: <20220502165807.529624-1-pgonda@google.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
A reference to the framebuffer device struct fb_info is stored in the file
private data, but this reference could no longer be valid and must not be
accessed directly. Instead, the file_fb_info() accessor function must be
used since it does sanity checking to make sure that the fb_info is valid.
This can happen for example if the registered framebuffer device is for a
driver that just uses a framebuffer provided by the system firmware. In
that case, the fbdev core would unregister the framebuffer device when a
real video driver is probed and ask to remove conflicting framebuffers.
The bug has been present for a long time but commit 27599aacbaef ("fbdev:
Hot-unplug firmware fb devices on forced removal") unmasked it since the
fbdev core started unregistering the framebuffers' devices associated.
Fixes: 27599aacbaef ("fbdev: Hot-unplug firmware fb devices on forced removal") Reported-by: Maxime Ripard <maxime@cerno.tech> Reported-by: Junxiao Chang <junxiao.chang@intel.com> Signed-off-by: Javier Martinez Canillas <javierm@redhat.com> Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220502135014.377945-1-javierm@redhat.com Signed-off-by: Sasha Levin <sashal@kernel.org>
On some x86 processors, CPUID leaf 0xA provides information
on Architectural Performance Monitoring features. It
advertises a PMU version which Qemu uses to determine the
availability of additional MSRs to manage the PMCs.
Upon receiving a KVM_GET_SUPPORTED_CPUID ioctl request for
the same, the kernel constructs return values based on the
x86_pmu_capability irrespective of the vendor.
This leaf and the additional MSRs are not supported on AMD
and Hygon processors. If AMD PerfMonV2 is detected, the PMU
version is set to 2 and guest startup breaks because of an
attempt to access a non-existent MSR. Return zeros to avoid
this.
Fixes: a6c06ed1a60a ("KVM: Expose the architectural performance monitoring CPUID leaf") Reported-by: Vasant Hegde <vasant.hegde@amd.com> Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Message-Id: <3fef83d9c2b2f7516e8ff50d60851f29a4bcb716.1651058600.git.sandipan.das@amd.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
syzbot is reporting use-after-free read in tcp_retransmit_timer() [1],
for TCP socket used by RDS is accessing sock_net() without acquiring a
refcount on net namespace. Since TCP's retransmission can happen after
a process which created net namespace terminated, we need to explicitly
acquire a refcount.
Link: https://syzkaller.appspot.com/bug?extid=694120e1002c117747ed Reported-by: syzbot <syzbot+694120e1002c117747ed@syzkaller.appspotmail.com> Fixes: 26abe14379f8e2fa ("net: Modify sk_alloc to not reference count the netns of kernel sockets.") Fixes: 8a68173691f03661 ("net: sk_clone_lock() should only do get_net() if the parent is not a kernel socket") Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Tested-by: syzbot <syzbot+694120e1002c117747ed@syzkaller.appspotmail.com> Link: https://lore.kernel.org/r/a5fb1fc4-2284-3359-f6a0-e4e390239d7b@I-love.SAKURA.ne.jp Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
pwmchip_add() unconditionally assigns the base ID dynamically. Commit f9a8ee8c8bcd1 ("pwm: Always allocate PWM chip base ID dynamically")
dropped all base assignment from drivers under drivers/pwm/. It missed
this driver. Fix that.
The cr16 interval timers are not synchronized across CPUs, even with just
one dual-core CPU. This becomes visible if the machines have a longer
uptime.
On Linux, empty symlinks are invalid, and attempting to create one with
the system call symlink(2) results in an -ENOENT error and this is
explicitly documented in the man page.
If we rename a symlink that was created in the current transaction and its
parent directory was logged before, we actually end up logging the symlink
without logging its content, which is stored in an inline extent. That
means that after a power failure we can end up with an empty symlink,
having no content and an i_size of 0 bytes.
It can be easily reproduced like this:
$ mkfs.btrfs -f /dev/sdc
$ mount /dev/sdc /mnt
$ mkdir /mnt/testdir
$ sync
# Create a file inside the directory and fsync the directory.
$ touch /mnt/testdir/foo
$ xfs_io -c "fsync" /mnt/testdir
# Create a symlink inside the directory and then rename the symlink.
$ ln -s /mnt/testdir/foo /mnt/testdir/bar
$ mv /mnt/testdir/bar /mnt/testdir/baz
# Now fsync again the directory, this persist the log tree.
$ xfs_io -c "fsync" /mnt/testdir
<power failure>
$ mount /dev/sdc /mnt
$ stat -c %s /mnt/testdir/baz
0
$ readlink /mnt/testdir/baz
$
Fix this by always logging symlinks in full mode (LOG_INODE_ALL), so that
their content is also logged.
A test case for fstests will follow.
CC: stable@vger.kernel.org # 4.9+ Signed-off-by: Filipe Manana <fdmanana@suse.com> Signed-off-by: David Sterba <dsterba@suse.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AlphaProject AP-SH4A-3A/AP-SH4AD-0A SH boards use IRQ0 for their SMSC
LAN911x Ethernet chip, so the networking on them must have been broken by
commit 965b2aa78fbc ("net/smsc911x: fix irq resource allocation failure")
which filtered out 0 as well as the negative error codes -- it was kinda
correct at the time, as platform_get_irq() could return 0 on of_irq_get()
failure and on the actual 0 in an IRQ resource. This issue was fixed by
me (back in 2016!), so we should be able to fix this driver to allow IRQ0
usage again...
When merging this to the stable kernels, make sure you also merge commit e330b9a6bb35 ("platform: don't return 0 from platform_get_irq[_byname]()
on error") -- that's my fix to platform_get_irq() for the DT platforms...
As discussed here with Ido Schimmel:
https://patchwork.kernel.org/project/netdevbpf/patch/20220224102908.5255-2-jianbol@nvidia.com/
the default conform-exceed action is "reclassify", for a reason we don't
really understand.
The point is that hardware can't offload that police action, so not
specifying "conform-exceed" was always wrong, even though the command
used to work in hardware (but not in software) until the kernel started
adding validation for it.
Fix the command used by the selftest by making the policer drop on
exceed, and pass the packet to the next action (goto) on conform.
Fixes: 8cd6b020b644 ("selftests: ocelot: add some example VCAP IS1, IS2 and ES0 tc offloads") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Link: https://lore.kernel.org/r/20220503121428.842906-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In bnxt_poll_p5(), we first check cpr->has_more_work. If it is true,
we are in NAPI polling mode and we will call __bnxt_poll_cqs() to
continue polling. It is possible to exhanust the budget again when
__bnxt_poll_cqs() returns.
We then enter the main while loop to check for new entries in the NQ.
If we had previously exhausted the NAPI budget, we may call
__bnxt_poll_work() to process an RX entry with zero budget. This will
cause packets to be dropped unnecessarily, thinking that we are in the
netpoll path. Fix it by breaking out of the while loop if we need
to process an RX NQ entry with no budget left. We will then exit
NAPI and stay in polling mode.
Fixes: 389a877a3b20 ("bnxt_en: Process the NQ under NAPI continuous polling.") Reviewed-by: Andy Gospodarek <andrew.gospodarek@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On older chips, RFS is capable if we can reserve the number of vnics that
is equal to RX rings + 1. But since RX rings is still set to 0 in this
code path, we may mistakenly think that RFS is supported for 0 RX rings.
Later, when the default RX rings are reserved and we try to enable
RFS, it would fail and cause bnxt_open() to fail unnecessarily.
We fix this in 2 places. bnxt_rfs_capable() will always return false if
RX rings is not yet set. bnxt_init_dflt_ring_mode() will call
bnxt_set_dflt_rfs() which will always clear the RFS flags if RFS is not
supported.
Fixes: 20d7d1c5c9b1 ("bnxt_en: reliably allocate IRQ table on reset to avoid crash") Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In emulated environments, the bridge ports enslaved to br1 get a carrier
before changing br1's PVID. This means that by the time the PVID is
changed, br1 is already operational and configured with an IPv6
link-local address.
When the test is run with netdevs registered by mlxsw, changing the PVID
is vetoed, as changing the VID associated with an existing L3 interface
is forbidden. This restriction is similar to the 8021q driver's
restriction of changing the VID of an existing interface.
Fix this by taking br1 down and bringing it back up when it is fully
configured.
With this fix, the test reliably passes on top of both the SW and HW
data paths (emulated or not).
Fixes: 239e754af854 ("selftests: forwarding: Test mirror-to-gretap w/ UL 802.1q") Signed-off-by: Ido Schimmel <idosch@nvidia.com> Reviewed-by: Petr Machata <petrm@nvidia.com> Link: https://lore.kernel.org/r/20220502084507.364774-1-idosch@nvidia.com Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AF_RXRPC doesn't currently enable IPv6 UDP Tx checksums on the transport
socket it opens and the checksums in the packets it generates end up 0.
It probably should also enable IPv6 UDP Rx checksums and IPv4 UDP
checksums. The latter only seem to be applied if the socket family is
AF_INET and don't seem to apply if it's AF_INET6. IPv4 packets from an
IPv6 socket seem to have checksums anyway.
What seems to have happened is that the inet_inv_convert_csum() call didn't
get converted to the appropriate udp_port_cfg parameters - and
udp_sock_create() disables checksums unless explicitly told not too.
Fix this by enabling the three udp_port_cfg checksum options.
Fixes: 1a9b86c9fd95 ("rxrpc: use udp tunnel APIs instead of open code in rxrpc_open_socket") Reported-by: Marc Dionne <marc.dionne@auristor.com> Signed-off-by: David Howells <dhowells@redhat.com> Reviewed-by: Xin Long <lucien.xin@gmail.com> Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: Vadim Fedorenko <vfedorenko@novek.ru>
cc: David S. Miller <davem@davemloft.net>
cc: linux-afs@lists.infradead.org Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever RCU protected list replaces an object,
the pointer to the new object needs to be updated
_before_ the call to kfree_rcu() or call_rcu()
Also ip6_mc_msfilter() needs to update the pointer
before releasing the mc_lock mutex.
Note that linux-5.13 was supporting kfree_rcu(NULL, rcu),
so this fix does not need the conditional test I was
forced to use in the equivalent patch for IPv4.
Fixes: 882ba1f73c06 ("mld: convert ipv6_mc_socklist->sflist to RCU") Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If wq has only one page, we need to check wqe rolling over page by
compare end_idx and curr_idx, and then copy wqe to shadow wqe to
avoid out of bound access.
This work has been done in hinic_get_wqe, but missed for hinic_read_wqe.
This patch fixes it, and removes unnecessary MASKED_WQE_IDX().
Current DP driver implementation has adding safe mode done at
dp_hpd_plug_handle() which is expected to be executed under event
thread context.
However there is possible circular locking happen (see blow stack trace)
after edp driver call dp_hpd_plug_handle() from dp_bridge_enable() which
is executed under drm_thread context.
After review all possibilities methods and as discussed on
https://patchwork.freedesktop.org/patch/483155/, supporting EDID
compliance tests in the driver is quite hacky. As seen with other
vendor drivers, supporting these will be much easier with IGT. Hence
removing all the related fail safe code for it so that no possibility
of circular lock will happen. Reviewed-by: Stephen Boyd <swboyd@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
======================================================
WARNING: possible circular locking dependency detected
5.15.35-lockdep #6 Tainted: G W
------------------------------------------------------
frecon/429 is trying to acquire lock: ffffff808dc3c4e8 (&dev->mode_config.mutex){+.+.}-{3:3}, at:
dp_panel_add_fail_safe_mode+0x4c/0xa0
but task is already holding lock: ffffff808dc441e0 (&kms->commit_lock[i]){+.+.}-{3:3}, at: lock_crtcs+0xb4/0x124
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
The program uses CLOCK_TAI as default clock since it was added to the
Linux repo. In commit:
| 040806343bb4 ("selftests/net: so_txtime multi-host support")
a help text stating the wrong default clock was added.
This patch fixes the help text.
Fixes: 040806343bb4 ("selftests/net: so_txtime multi-host support") Cc: Carlos Llamas <cmllamas@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Carlos Llamas <cmllamas@google.com> Link: https://lore.kernel.org/r/20220502094638.1921702-3-mkl@pengutronix.de Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the parsing of the cmd line supplied start time on 32
bit systems. A "long" on 32 bit systems is only 32 bit wide and cannot
hold a timestamp in nano second resolution.
Fixes: 040806343bb4 ("selftests/net: so_txtime multi-host support") Cc: Carlos Llamas <cmllamas@google.com> Cc: Willem de Bruijn <willemb@google.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Acked-by: Willem de Bruijn <willemb@google.com> Reviewed-by: Carlos Llamas <cmllamas@google.com> Link: https://lore.kernel.org/r/20220502094638.1921702-2-mkl@pengutronix.de Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Whenever RCU protected list replaces an object,
the pointer to the new object needs to be updated
_before_ the call to kfree_rcu() or call_rcu()
Because kfree_rcu(ptr, rcu) got support for NULL ptr
only recently in commit 12edff045bc6 ("rcu: Make kfree_rcu()
ignore NULL pointers"), I chose to use the conditional
to make sure stable backports won't miss this detail.
if (psl)
kfree_rcu(psl, rcu);
net/ipv6/mcast.c has similar issues, addressed in a separate patch.
[1]
BUG: KASAN: use-after-free in ip_mc_sf_allow+0x6bb/0x6d0 net/ipv4/igmp.c:2655
Read of size 4 at addr ffff88807d37b904 by task syz-executor.5/908
Second to last potentially related work creation:
kasan_save_stack+0x1e/0x40 mm/kasan/common.c:38
__kasan_record_aux_stack+0x7e/0x90 mm/kasan/generic.c:348
call_rcu+0x99/0x790 kernel/rcu/tree.c:3074
mpls_dev_notify+0x552/0x8a0 net/mpls/af_mpls.c:1656
notifier_call_chain+0xb5/0x200 kernel/notifier.c:84
call_netdevice_notifiers_info+0xb5/0x130 net/core/dev.c:1938
call_netdevice_notifiers_extack net/core/dev.c:1976 [inline]
call_netdevice_notifiers net/core/dev.c:1990 [inline]
unregister_netdevice_many+0x92e/0x1890 net/core/dev.c:10751
default_device_exit_batch+0x449/0x590 net/core/dev.c:11245
ops_exit_list+0x125/0x170 net/core/net_namespace.c:167
cleanup_net+0x4ea/0xb00 net/core/net_namespace.c:594
process_one_work+0x996/0x1610 kernel/workqueue.c:2289
worker_thread+0x665/0x1080 kernel/workqueue.c:2436
kthread+0x2e9/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298
The buggy address belongs to the object at ffff88807d37b900
which belongs to the cache kmalloc-64 of size 64
The buggy address is located 4 bytes inside of
64-byte region [ffff88807d37b900, ffff88807d37b940)
Memory state around the buggy address: ffff88807d37b800: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc ffff88807d37b880: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc
>ffff88807d37b900: fa fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc
^ ffff88807d37b980: fb fb fb fb fb fb fb fb fc fc fc fc fc fc fc fc ffff88807d37ba00: 00 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc
Fixes: c85bb41e9318 ("igmp: fix ip_mc_sf_allow race [v5]") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Cc: Flavio Leitner <fbl@sysclose.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'tmp_node' need be put before returning from cpsw_probe_dt(),
so add missing of_node_put() in error path.
Fixes: ed3525eda4c4 ("net: ethernet: ti: introduce cpsw switchdev based driver part 1 - dual-emac") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need to declare attributes such as the ctime, mtime and
block size invalid when we're just returning a delegation, so it is
inappropriate to call nfs_post_op_update_inode_force_wcc().
Instead, just call nfs_refresh_inode() after faking up the change
attribute. We know that the GETATTR op occurs before the DELEGRETURN, so
we are safe when doing this.
Fixes: 0bc2c9b4dca9 ("NFSv4: Don't discard the attributes returned by asynchronous DELEGRETURN") Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some net events in irdma_net_event notifier, the netdev can be NULL
which will cause a crash in rdma_vlan_dev_real_dev. Fix this by moving
all processing to the NETEVENT_NEIGH_UPDATE case where the netdev is
guaranteed to not be NULL.
Fixes: 6702bc147448 ("RDMA/irdma: Fix netdev notifications for vlan's") Link: https://lore.kernel.org/r/20220425181703.1634-4-shiraz.saleem@intel.com Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com> Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com> Signed-off-by: Jason Gunthorpe <jgg@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
QP destroy is synchronous and waits for its refcnt to be decremented in
irdma_cm_node_free_cb (for iWARP) which fires after the RCU grace period
elapses.
Applications running a large number of connections are exposed to high
wait times on destroy QP for events like SIGABORT.
The long pole for this wait time is the firing of the call_rcu callback
during a CM node destroy which can be slow. It holds the QP reference
count and blocks the destroy QP from completing.
call_rcu only needs to make sure that list walkers have a reference to the
cm_node object before freeing it and thus need to wait for grace period
elapse. The rest of the connection teardown in irdma_cm_node_free_cb is
moved out of the grace period wait in irdma_destroy_connection. Also,
replace call_rcu with a simple kfree_rcu as it just needs to do a kfree on
the cm_node
When connection establishment fails in iWARP mode, an app can drain the
QPs and hang because flush isn't issued when the QP is modified from RTR
state to error. Issue a flush in this case using function
irdma_cm_disconn().
Update irdma_cm_disconn() to do flush when cm_id is NULL, which is the
case when the QP is in RTR state and there is an error in the connection
establishment.
The calling of siw_cm_upcall and detaching new_cep with its listen_cep
should be atomistic semantics. Otherwise siw_reject may be called in a
temporary state, e,g, siw_cm_upcall is called but the new_cep->listen_cep
has not being cleared.
The quirk ALC287_FIXUP_CS35L41_I2C_2 needs to chain the quirk
ALC269_FIXUP_THINKPAD_ACPI, otherwise the mute led will not work if a
thinkpad machine applies that quirk.
And it will be safe if non-thinkpad machines apply that quirk since
hda_fixup_thinkpad_acpi() will check and return in this case.
Fixes: ae7abe36e352e ("ALSA: hda/realtek: Add CS35L41 support for Thinkpad laptops") Signed-off-by: Hui Wang <hui.wang@canonical.com> Link: https://lore.kernel.org/r/20220422073937.10073-1-hui.wang@canonical.com Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 92d25637a3a4 ("kselftest: signal all child processes"), tests
are executed in background process groups. This means that trying to read
from stdin now throws SIGTTIN when stdin is a TTY, which breaks some
seccomp selftests that try to use read(0, NULL, 0) as a dummy syscall.
The simplest way to fix that is probably to just use -1 instead of 0 as
the dummy read()'s FD.
When resolving the decap route device for a tunnel decap rule,
the result may be an OVS internal port device.
Prior to adding the support for internal port offload, such case
would result in using the uplink as the default decap route device
which allowed devices that can't support internal port offload
to offload this decap rule.
This behavior got broken by adding the internal port offload which
will fail in case the device can't support internal port offload.
To restore the old behavior, use the uplink device as the decap
route as before when internal port offload is not supported.
Fixes: b16eb3c81fe2 ("net/mlx5: Support internal port as decap route device") Signed-off-by: Ariel Levkovich <lariel@nvidia.com> Reviewed-by: Maor Dickman <maord@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Referenced change added check to skip updating fib when new fib instance
has same or lower priority. However, new fib instance can be an update on
same dst address as existing one even though the structure is another
instance that has different address. Ignoring events on such instances
causes multipath LAG state to not be correctly updated.
Track 'dst' and 'dst_len' fields of fib event fib_entry_notifier_info
structure and don't skip events that have the same value of that fields.
Referenced change incorrectly sets single path fib_info even when LAG is
not active. Fix it by moving call to mlx5_lag_fib_set() into conditional
that verifies LAG state.
Recent commit that modified fib route event handler to handle events
according to their priority introduced use-after-free[0] in mp->mfi pointer
usage. The pointer now is not just cached in order to be compared to
following fib_info instances, but is also dereferenced to obtain
fib_priority. However, since mlx5 lag code doesn't hold the reference to
fin_info during whole mp->mfi lifetime, it could be used after fib_info
instance has already been freed be kernel infrastructure code.
Don't ever dereference mp->mfi pointer. Refactor it to be 'const void*'
type and cache fib_info priority in dedicated integer. Group
fib_info-related data into dedicated 'fib' structure that will be further
extended by following patches in the series.
[0]:
[ 203.588029] ==================================================================
[ 203.590161] BUG: KASAN: use-after-free in mlx5_lag_fib_update+0xabd/0xd60 [mlx5_core]
[ 203.592386] Read of size 4 at addr ffff888144df2050 by task kworker/u20:4/138
[ 203.681455] Memory state around the buggy address:
[ 203.682421] ffff888144df1f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 203.683863] ffff888144df1f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 203.685310] >ffff888144df2000: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 203.686701] ^
[ 203.687820] ffff888144df2080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 203.689226] ffff888144df2100: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 203.690620] ==================================================================
The sync reset flow can lead to the following deadlock when
poll_sync_reset() is called by timer softirq and waiting on
del_timer_sync() for the same timer. Fix that by moving the part of the
flow that waits for the timer to reset_reload_work.
Double clear of reset requested state can lead to NULL pointer as it
will try to delete the timer twice. This can happen for example on a
race between abort from FW and pci error or reset. Avoid such case using
test_and_clear_bit() to verify only one time reset requested state clear
flow. Similarly use test_and_set_bit() to verify only one time reset
requested state set flow.
The cited commits didn't use proper matching on inner TTC
as a result distribution of encapsulated packets wasn't symmetric
between the physical ports.
Fixes: 4c71ce50d2fe ("net/mlx5: Support partial TTC rules") Fixes: 8e25a2bc6687 ("net/mlx5: Lag, add support to create TTC tables for LAG port selection") Signed-off-by: Mark Bloch <mbloch@nvidia.com> Reviewed-by: Maor Gottlieb <maorg@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__mlx5_tc_ct_entry_put() queues release of tuple related to some ct FT,
if that is the last reference to that tuple, the actual deletion of
the tuple can happen after the FT is already destroyed and freed.
Flush the used workqueue before destroying the ct FT.
Fixes: a2173131526d ("net/mlx5e: CT: manage the lifetime of the ct entry object") Reviewed-by: Oz Shlomo <ozsh@nvidia.com> Signed-off-by: Paul Blakey <paulb@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, match VLAN rule also matches packets that have multiple VLAN
headers. This behavior is similar to buggy flower classifier behavior that
has recently been fixed. Fix the issue by matching on
outer_second_cvlan_tag with value 0 which will cause the HW to verify the
packet doesn't contain second vlan header.
When OVS internal port is the vtep device, the first decap
rule is matching on the internal port's vport metadata value
and then changes the metadata to be the uplink's value.
Therefore, following rules on the tunnel, in chain > 0, should
avoid matching on internal port metadata and use the uplink
vport metadata instead.
Select the uplink's metadata value for the source vport match
in case the rule is in chain greater than zero, even if the tunnel
route device is internal port.
Resource dump menu may span over more than a single page, support it.
Otherwise, menu read may result in a memory access violation: reading
outside of the allocated page.
Note that page format of the first menu page contains menu headers while
the proceeding menu pages contain only records.
The KASAN logs are as follows:
BUG: KASAN: slab-out-of-bounds in strcmp+0x9b/0xb0
Read of size 1 at addr ffff88812b2e1fd0 by task systemd-udevd/496
CPU: 5 PID: 496 Comm: systemd-udevd Tainted: G B 5.16.0_for_upstream_debug_2022_01_10_23_12 #1
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x57/0x7d
print_address_description.constprop.0+0x1f/0x140
? strcmp+0x9b/0xb0
? strcmp+0x9b/0xb0
kasan_report.cold+0x83/0xdf
? strcmp+0x9b/0xb0
strcmp+0x9b/0xb0
mlx5_rsc_dump_init+0x4ab/0x780 [mlx5_core]
? mlx5_rsc_dump_destroy+0x80/0x80 [mlx5_core]
? lockdep_hardirqs_on_prepare+0x286/0x400
? raw_spin_unlock_irqrestore+0x47/0x50
? aomic_notifier_chain_register+0x32/0x40
mlx5_load+0x104/0x2e0 [mlx5_core]
mlx5_init_one+0x41b/0x610 [mlx5_core]
....
The buggy address belongs to the object at ffff88812b2e0000
which belongs to the cache kmalloc-4k of size 4096
The buggy address is located 4048 bytes to the right of
4096-byte region [ffff88812b2e0000, ffff88812b2e1000)
The buggy address belongs to the page:
page:000000009d69807a refcount:1 mapcount:0 mapping:0000000000000000 index:0xffff88812b2e6000 pfn:0x12b2e0
head:000000009d69807a order:3 compound_mapcount:0 compound_pincount:0
flags: 0x8000000000010200(slab|head|zone=2)
raw: 80000000000102000000000000000000dead000000000001ffff888100043040
raw: ffff88812b2e6000000000008004000000000001ffffffff0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address: ffff88812b2e1e80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff88812b2e1f00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88812b2e1f80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^ ffff88812b2e2000: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff88812b2e2080: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
==================================================================
Fixes: 12206b17235a ("net/mlx5: Add support for resource dump") Signed-off-by: Aya Levin <ayal@nvidia.com> Reviewed-by: Moshe Shemesh <moshe@nvidia.com> Signed-off-by: Saeed Mahameed <saeedm@nvidia.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting dscp2prio during the driver reload can cause dcb ieee app list to
be not empty after the reload finish and as a result to a conflict between
the priority trust state reported by the app and the state in the device
register.
Reset the dcb ieee app list on initialization in case this is
conflicting with the register status.
It will cause null-ptr-deref in resource_size(), if platform_get_resource()
returns NULL, move calling resource_size() after devm_ioremap_resource() that
will check 'res' to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: 46d1fb072e76 ("iommu/dart: Add DART iommu driver") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Reviewed-by: Sven Peter <sven@svenpeter.dev> Link: https://lore.kernel.org/r/20220425090826.2532165-1-yangyingliang@huawei.com Signed-off-by: Joerg Roedel <jroedel@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The page fault handling framework in the IOMMU core explicitly states
that it doesn't handle PCI PASID Stop Marker and the IOMMU drivers must
discard them before reporting faults. This handles Stop Marker messages
in prq_event_thread() before reporting events to the core.
The VT-d driver explicitly drains the pending page requests when a CPU
page table (represented by a mm struct) is unbound from a PASID according
to the procedures defined in the VT-d spec. The Stop Marker messages do
not need a response. Hence, it is safe to drop the Stop Marker messages
silently if any of them is found in the page request queue.
As pointed out by Sascha Hauer, this patch changes:
if (pmc->config && !pcm->config->prepare_slave_config)
<do nothing>
to:
if (pmc->config && !pcm->config->prepare_slave_config)
snd_dmaengine_pcm_prepare_slave_config()
This breaks the drivers that do not need a call to
dmaengine_slave_config(). Drivers that still need to call
snd_dmaengine_pcm_prepare_slave_config(), but have a NULL
pcm->config->prepare_slave_config should use
snd_dmaengine_pcm_prepare_slave_config() as their prepare_slave_config
callback.
Fixes: 9a1e13440a4f ("ASoC: dmaengine: do not use a NULL prepare_slave_config() callback") Reported-by: Sascha Hauer <sha@pengutronix.de> Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com> Link: https://lore.kernel.org/r/20220421125403.2180824-1-codrin.ciubotariu@microchip.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Explicitly disable PEC when the client does not support it.
The problematic scenario is the following. A device with enabled PEC
support is up and running and a kernel driver is loaded.
Then the driver is unloaded (or device unbound), the HW device
is reconfigured externally (e.g. by i2cset) to advertise itself as not
supporting PEC. Without a new code, at the second load of the driver
(or bind) the "flags" variable is not updated to avoid PEC usage. As a
consequence the further communication with the device is done with
the PEC enabled, which is wrong and may fail.
The implementation first disable the I2C_CLIENT_PEC flag, then the old
code enable it if needed.
When removing the adt7470 module, a warning might be printed:
do not call blocking ops when !TASK_RUNNING; state=1
set at [<ffffffffa006052b>] adt7470_update_thread+0x7b/0x130 [adt7470]
This happens because adt7470_update_thread() can leave the kthread in
TASK_INTERRUPTIBLE state when the kthread is being stopped before
the call of set_current_state(). Since kthread_exit() might sleep in
exit_signals(), the warning is printed.
Fix that by using schedule_timeout_interruptible() and removing
the call of set_current_state().
This causes TASK_INTERRUPTIBLE to be set after kthread_should_stop()
which might cause the kthread to exit.
Reported-by: Zheyu Ma <zheyuma97@gmail.com> Fixes: 93cacfd41f82 (hwmon: (adt7470) Allow faster removal) Signed-off-by: Armin Wolf <W_Armin@gmx.de> Tested-by: Zheyu Ma <zheyuma97@gmail.com> Link: https://lore.kernel.org/r/20220407101312.13331-1-W_Armin@gmx.de Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When one port's input state get inverted (eg. from low to hight) after
pca953x_irq_setup but before setting irq_mask (by some other driver such as
"gpio-keys"), the next inversion of this port (eg. from hight to low) will not
be triggered any more (because irq_stat is not updated at the first time). Issue
should be fixed after this commit.
The fwnode of GPIO IRQ must be set to its own fwnode, not the fwnode of the
parent IRQ. Therefore, this sets own fwnode instead of the parent IRQ fwnode to
GPIO IRQ's.
There are sleep in atomic bug that could cause kernel panic during
firmware download process. The root cause is that nlmsg_new with
GFP_KERNEL parameter is called in fw_dnld_timeout which is a timer
handler. The call trace is shown below:
BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265
Call Trace:
kmem_cache_alloc_node
__alloc_skb
nfc_genl_fw_download_done
call_timer_fn
__run_timers.part.0
run_timer_softirq
__do_softirq
...
The nlmsg_new with GFP_KERNEL parameter may sleep during memory
allocation process, and the timer handler is run as the result of
a "software interrupt" that should not call any other function
that could sleep.
This patch changes allocation mode of netlink message from GFP_KERNEL
to GFP_ATOMIC in order to prevent sleep in atomic bug. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
There are destructive operations such as nfcmrvl_fw_dnld_abort and
gpio_free in nfcmrvl_nci_unregister_dev. The resources such as firmware,
gpio and so on could be destructed while the upper layer functions such as
nfcmrvl_fw_dnld_start and nfcmrvl_nci_recv_frame is executing, which leads
to double-free, use-after-free and null-ptr-deref bugs.
There are three situations that could lead to double-free bugs.
The firmware struct is deallocated in position (1) and deallocated
in position (2) again.
The crash trace triggered by POC is like below:
BUG: KASAN: double-free or invalid-free in fw_dnld_over
Call Trace:
kfree
fw_dnld_over
nfcmrvl_nci_unregister_dev
nci_uart_tty_close
tty_ldisc_kill
tty_ldisc_hangup
__tty_hangup.part.0
tty_release
...
What's more, there are also use-after-free and null-ptr-deref bugs
in nfcmrvl_fw_dnld_start. If we deallocate firmware struct, gpio or
set null to the members of priv->fw_dnld in nfcmrvl_nci_unregister_dev,
then, we dereference firmware, gpio or the members of priv->fw_dnld in
nfcmrvl_fw_dnld_start, the UAF or NPD bugs will happen.
This patch reorders destructive operations after nci_unregister_device
in order to synchronize between cleanup routine and firmware download
routine.
The nci_unregister_device is well synchronized. If the device is
detaching, the firmware download routine will goto error. If firmware
download routine is executing, nci_unregister_device will wait until
firmware download routine is finished.
Fixes: 3194c6870158 ("NFC: nfcmrvl: add firmware download support") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The device_is_registered() in nfc core is used to check whether
nfc device is registered in netlink related functions such as
nfc_fw_download(), nfc_dev_up() and so on. Although device_is_registered()
is protected by device_lock, there is still a race condition between
device_del() and device_is_registered(). The root cause is that
kobject_del() in device_del() is not protected by device_lock.
The device_is_registered() returns the value of state_in_sysfs and
the state_in_sysfs is set to zero in kobject_del(). If we pass check in
position (1), then set zero in position (2). As a result, the check
in position (1) is useless.
This patch uses bool variable instead of device_is_registered() to judge
whether the nfc device is registered, which is well synchronized.
Fixes: 3e256b8f8dfa ("NFC: add nfc subsystem core") Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous split budget between TX and RX made it return not using
the entire budget but at the same time not having calling called
napi_complete. This sometimes led to the poll to not be called, and at
the same time having TX and RX interrupts disabled resulting in the
driver getting stuck.
Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores") Link: https://lore.kernel.org/all/20220429084656.29788-4-andreas@gaisler.com Cc: stable@vger.kernel.org Signed-off-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a carry over from the CAN_RAW socket (which allows to change the CAN
interface while mantaining the filter setup) the re-binding of the
CAN_ISOTP socket needs to take care about CAN ID address information and
subscriptions. It turned out that this feature is so limited (e.g. the
sockopts remain fix) that it finally has never been needed/used.
In opposite to the stateless CAN_RAW socket the switching of the CAN ID
subscriptions might additionally lead to an interrupted ongoing PDU
reception. So better remove this unneeded complexity.
Fixes: e057dd3fc20f ("can: add ISO 15765-2:2016 transport protocol") Link: https://lore.kernel.org/all/20220422082337.1676-1-socketcan@hartkopp.net Cc: stable@vger.kernel.org Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are deadlocks caused by del_timer_sync(&priv->hang_timer) and
del_timer_sync(&priv->rr_timer) in grcan_close(), one of the deadlocks
are shown below:
We hold priv->lock in position (1) of thread 1 and use
del_timer_sync() to wait timer to stop, but timer handler also need
priv->lock in position (2) of thread 2. As a result, grcan_close()
will block forever.
This patch extracts del_timer_sync() from the protection of
spin_lock_irqsave(), which could let timer handler to obtain the
needed lock.
Link: https://lore.kernel.org/all/20220425042400.66517-1-duoming@zju.edu.cn Fixes: 6cec9b07fe6a ("can: grcan: Add device driver for GRCAN and GRHCAN cores") Cc: stable@vger.kernel.org Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Reviewed-by: Andreas Larsson <andreas@gaisler.com> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Read requests that return with NRF error are partially completed in
dasd_eckd_ese_read(). The function keeps track of the amount of
processed bytes and the driver will eventually return this information
back to the block layer for further processing via __dasd_cleanup_cqr()
when the request is in the final stage of processing (from the driver's
perspective).
For this, blk_update_request() is used which requires the number of
bytes to complete the request. As per documentation the nr_bytes
parameter is described as follows:
"number of bytes to complete for @req".
This was mistakenly interpreted as "number of bytes _left_ for @req"
leading to new requests with incorrect data length. The consequence are
inconsistent and completely wrong read requests as data from random
memory areas are read back.
Fix this by correctly specifying the amount of bytes that should be used
to complete the request.
Fixes: 5e6bdd37c552 ("s390/dasd: fix data corruption for thin provisioned devices") Cc: stable@vger.kernel.org # 5.3+ Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com> Reviewed-by: Stefan Haberland <sth@linux.ibm.com> Link: https://lore.kernel.org/r/20220505141733.1989450-5-sth@linux.ibm.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When reading unformatted tracks on ESE devices, the corresponding memory
areas are simply set to zero for each segment. This is done incorrectly
for blocksizes < 4096.
There are two problems. First, the increment of dst is done using the
counter of the loop (off), which is increased by blksize every
iteration. This leads to a much bigger increment for dst as actually
intended. Second, the increment of dst is done before the memory area
is set to 0, skipping a significant amount of bytes of memory.
This leads to illegal overwriting of memory and ultimately to a kernel
panic.
This is not a problem with 4k blocksize because
blk_queue_max_segment_size is set to PAGE_SIZE, always resulting in a
single iteration for the inner segment loop (bv.bv_len == blksize). The
incorrectly used 'off' value to increment dst is 0 and the correct
memory area is used.
In order to fix this for blksize < 4k, increment dst correctly using the
blksize and only do it at the end of the loop.
Fixes: 5e2b17e712cf ("s390/dasd: Add dynamic formatting support for ESE volumes") Cc: stable@vger.kernel.org # v5.3+ Signed-off-by: Jan Höppner <hoeppner@linux.ibm.com> Reviewed-by: Stefan Haberland <sth@linux.ibm.com> Link: https://lore.kernel.org/r/20220505141733.1989450-4-sth@linux.ibm.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For ESE devices we get an error for write operations on an unformatted
track. Afterwards the track will be formatted and the IO operation
restarted.
When using alias devices a track might be accessed by multiple requests
simultaneously and there is a race window that a track gets formatted
twice resulting in data loss.
Prevent this by remembering the amount of formatted tracks when starting
a request and comparing this number before actually formatting a track
on the fly. If the number has changed there is a chance that the current
track was finally formatted in between. As a result do not format the
track and restart the current IO to check.
The number of formatted tracks does not match the overall number of
formatted tracks on the device and it might wrap around but this is no
problem. It is only needed to recognize that a track has been formatted at
all in between.
Fixes: 5e2b17e712cf ("s390/dasd: Add dynamic formatting support for ESE volumes") Cc: stable@vger.kernel.org # 5.3+ Signed-off-by: Stefan Haberland <sth@linux.ibm.com> Reviewed-by: Jan Hoeppner <hoeppner@linux.ibm.com> Link: https://lore.kernel.org/r/20220505141733.1989450-3-sth@linux.ibm.com Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
projects / linux-stable / log