Sedat Dilek noticed that I had an extraneous semicolon at the end of a
line in the previous patch.
It's harmless, but unintentional, and while compilers just treat it as
an extra empty statement, for all I know some other tooling might warn
about it. So clean it up before other people notice too ;)
The IMR was assumed to be preserved when suspending to S4 and S5
states, but community reports invalidate that assumption, the hardware
seems to be powered off and the IMR memory content cleared.
Make sure regular boot with firmware download is used for S4 and S5.
We currently don't have a means to differentiate between S3, S4 and
S5. Add definitions so that we have select different code paths
depending on the target state in follow-up patches.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com> Link: https://lore.kernel.org/r/20220616201818.130802-3-pierre-louis.bossart@linux.intel.com Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the pipe is closed, we mark the associated watchqueue defunct by
calling watch_queue_clear(). However, while that is protected by the
watchqueue lock, new watchqueue entries aren't actually added under that
lock at all: they use the pipe->rd_wait.lock instead, and looking up
that pipe happens without any locking.
The watchqueue code uses the RCU read-side section to make sure that the
wqueue entry itself hasn't disappeared, but that does not protect the
pipe_info in any way.
So make sure to actually hold the wqueue lock when posting watch events,
properly serializing against the pipe being torn down.
On AMD IBRS does not prevent Retbleed; as such use IBPB before a
firmware call to flush the branch history state.
And because in order to do an EFI call, the kernel maps a whole lot of
the kernel page table into the EFI page table, do an IBPB just in case
in order to prevent the scenario of poisoning the BTB and causing an EFI
call using the unprotected RET there.
In order for a file to access its own directory entry set,
exfat_inode_info(ei) has two copied values. One is ei->dir, which is
a snapshot of exfat_chain of the parent directory, and the other is
ei->entry, which is the offset of the start of the directory entry set
in the parent directory.
Since the parent directory can be updated after the snapshot point,
it should be used only for accessing one's own directory entry set.
However, as of now, during renaming, it could try to traverse or to
allocate clusters via snapshot values, it does not make sense.
This potential problem has been revealed when exfat_update_parent_info()
was removed by commit d8dad2588add ("exfat: fix referencing wrong parent
directory information after renaming"). However, I don't think it's good
idea to bring exfat_update_parent_info() back.
Instead, let's use the updated exfat_chain of parent directory diectly.
Fixes: d8dad2588add ("exfat: fix referencing wrong parent directory information after renaming") Reported-by: Wang Yugui <wangyugui@e16-tech.com> Signed-off-by: Sungjong Seo <sj1557.seo@samsung.com> Tested-by: Wang Yugui <wangyugui@e16-tech.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During renaming, the parent directory information maybe
updated. But the file/directory still references to the
old parent directory information.
This bug will cause 2 problems.
(1) The renamed file can not be written.
[10768.175172] exFAT-fs (sda1): error, failed to bmap (inode : 7afd50e4 iblock : 0, err : -5)
[10768.184285] exFAT-fs (sda1): Filesystem has been set read-only
ash: write error: Input/output error
(2) Some dentries of the renamed file/directory are not set
to deleted after removing the file/directory.
exfat_update_parent_info() is a workaround for the wrong parent
directory information being used after renaming. Now that bug is
fixed, this is no longer needed, so remove it.
Fixes: 5f2aa075070c ("exfat: add inode operations") Cc: stable@vger.kernel.org # v5.7+ Signed-off-by: Yuezhang Mo <Yuezhang.Mo@sony.com> Reviewed-by: Andy Wu <Andy.Wu@sony.com> Reviewed-by: Aoyama Wataru <wataru.aoyama@sony.com> Reviewed-by: Daniel Palmer <daniel.palmer@sony.com> Reviewed-by: Sungjong Seo <sj1557.seo@samsung.com> Signed-off-by: Namjae Jeon <linkinjeon@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Re-enable the registration of algorithms after fixes to (1) use
pre-allocated buffers in the datapath and (2) support the
CRYPTO_TFM_REQ_MAY_BACKLOG flag.
Reject requests with a source buffer that is bigger than the size of the
key. This is to prevent a possible integer underflow that might happen
when copying the source scatterlist into a linear buffer.
Cc: stable@vger.kernel.org Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Adam Guerin <adam.guerin@intel.com> Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
Reject requests with a source buffer that is bigger than the size of the
key. This is to prevent a possible integer underflow that might happen
when copying the source scatterlist into a linear buffer.
Cc: stable@vger.kernel.org Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Adam Guerin <adam.guerin@intel.com> Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The functions qat_dh_compute_value() allocates memory with
dma_alloc_coherent() if the source or the destination buffers are made
of multiple flat buffers or of a size that is not compatible with the
hardware.
This memory is then freed with dma_free_coherent() in the context of a
tasklet invoked to handle the response for the corresponding request.
According to Documentation/core-api/dma-api-howto.rst, the function
dma_free_coherent() cannot be called in an interrupt context.
Replace allocations with dma_alloc_coherent() in the function
qat_dh_compute_value() with kmalloc() + dma_map_single().
Cc: stable@vger.kernel.org Fixes: c9839143ebbf ("crypto: qat - Add DH support") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Adam Guerin <adam.guerin@intel.com> Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
After commit f5ff79fddf0e ("dma-mapping: remove CONFIG_DMA_REMAP"), if
the algorithms are enabled, the driver crashes with a BUG_ON while
executing vunmap() in the context of a tasklet. This is due to the fact
that the function dma_free_coherent() cannot be called in an interrupt
context (see Documentation/core-api/dma-api-howto.rst).
The functions qat_rsa_enc() and qat_rsa_dec() allocate memory with
dma_alloc_coherent() if the source or the destination buffers are made
of multiple flat buffers or of a size that is not compatible with the
hardware.
This memory is then freed with dma_free_coherent() in the context of a
tasklet invoked to handle the response for the corresponding request.
Replace allocations with dma_alloc_coherent() in the functions
qat_rsa_enc() and qat_rsa_dec() with kmalloc() + dma_map_single().
Cc: stable@vger.kernel.org Fixes: a990532023b9 ("crypto: qat - Add support for RSA algorithm") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Adam Guerin <adam.guerin@intel.com> Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
When an RSA key represented in form 2 (as defined in PKCS #1 V2.1) is
used, some components of the private key persist even after the TFM is
released.
Replace the explicit calls to free the buffers in qat_rsa_exit_tfm()
with a call to qat_rsa_clear_ctx() which frees all buffers referenced in
the TFM context.
Cc: stable@vger.kernel.org Fixes: 879f77e9071f ("crypto: qat - Add RSA CRT mode") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Adam Guerin <adam.guerin@intel.com> Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
The implementations of the crypto algorithms (aead, skcipher, etc) in
the QAT driver do not properly support requests with the
CRYPTO_TFM_REQ_MAY_BACKLOG flag set. If the HW queue is full, the driver
returns -EBUSY but does not enqueue the request. This can result in
applications like dm-crypt waiting indefinitely for the completion of a
request that was never submitted to the hardware.
Fix this by adding a software backlog queue: if the ring buffer is more
than eighty percent full, then the request is enqueued to a backlog
list and the error code -EBUSY is returned back to the caller.
Requests in the backlog queue are resubmitted at a later time, in the
context of the callback of a previously submitted request.
The request for which -EBUSY is returned is then marked as -EINPROGRESS
once submitted to the HW queues.
The submission loop inside the function qat_alg_send_message() has been
modified to decide which submission policy to use based on the request
flags. If the request does not have the CRYPTO_TFM_REQ_MAY_BACKLOG set,
the previous behaviour has been preserved.
Based on a patch by
Vishnu Das Ramachandran <vishnu.dasx.ramachandran@intel.com>
All the algorithms in qat_algs.c and qat_asym_algs.c use the same
pattern to submit messages to the HW queues. Move the submission loop
to a new function, qat_alg_send_message(), and share it between the
symmetric and the asymmetric algorithms.
As part of this rework, since the number of retries before returning an
error is inconsistent between the symmetric and asymmetric
implementations, set it to a value that works for both (i.e. 20, was 10
in qat_algs.c and 100 in qat_asym_algs.c)
In addition fix the return code reported when the HW queues are full.
In that case return -ENOSPC instead of -EBUSY.
Including stable in CC since (1) the error code returned if the HW queues
are full is incorrect and (2) to facilitate the backport of the next fix
"crypto: qat - add backlog mechanism".
Cc: stable@vger.kernel.org Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Marco Chiappero <marco.chiappero@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
In order to do DMAs, the QAT device requires that the scatterlist
structures are mapped and translated into a format that the firmware can
understand. This is defined as the composition of a scatter gather list
(SGL) descriptor header, the struct qat_alg_buf_list, plus a variable
number of flat buffer descriptors, the struct qat_alg_buf.
The allocation and mapping of these data structures is done each time a
request is received from the skcipher and aead APIs.
In an OOM situation, this behaviour might lead to a dead-lock if an
allocation fails.
Based on the conversation in [1], increase the size of the aead and
skcipher request contexts to include an SGL descriptor that can handle
a maximum of 4 flat buffers.
If requests exceed 4 entries buffers, memory is allocated dynamically.
Set to zero the context buffers containing the DH key before they are
freed.
This is a defense in depth measure that avoids keys to be recovered from
memory in case the system is compromised between the free of the buffer
and when that area of memory (containing keys) gets overwritten.
Cc: stable@vger.kernel.org Fixes: c9839143ebbf ("crypto: qat - Add DH support") Signed-off-by: Giovanni Cabiddu <giovanni.cabiddu@intel.com> Reviewed-by: Adam Guerin <adam.guerin@intel.com> Reviewed-by: Wojciech Ziemba <wojciech.ziemba@intel.com> Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: Sasha Levin <sashal@kernel.org>
This patch unsets ls_remove_len and ls_remove_name if a message
allocation of a remove messages fails. In this case we never send a
remove message out but set the per ls ls_remove_len ls_remove_name
variable for a pending remove. Unset those variable should indicate
possible waiters in wait_pending_remove() that no pending remove is
going on at this moment.
Cc: stable@vger.kernel.org Signed-off-by: Alexander Aring <aahringo@redhat.com> Signed-off-by: David Teigland <teigland@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
The register address used for the clock gate register is the base
register address coming from first reg map (ie. the generic
clock registers) instead of the second reg map defining the clock
gate register.
IBRS mitigation for spectre_v2 forces write to MSR_IA32_SPEC_CTRL at
every kernel entry/exit. On Enhanced IBRS parts setting
MSR_IA32_SPEC_CTRL[IBRS] only once at boot is sufficient. MSR writes at
every kernel entry/exit incur unnecessary performance loss.
When Enhanced IBRS feature is present, print a warning about this
unnecessary performance loss.
On a machine with the LBR format LBR_FORMAT_EIP_FLAGS2, when the TSX is
disabled, a TSX quirk is required to access LBR from registers.
The lbr_from_signext_quirk_needed() is introduced to determine whether
the TSX quirk should be applied. However, the
lbr_from_signext_quirk_needed() is invoked before the
intel_pmu_lbr_init(), which parses the LBR format information. Without
the correct LBR format information, the TSX quirk never be applied.
Move the lbr_from_signext_quirk_needed() into the intel_pmu_lbr_init().
Checking x86_pmu.lbr_has_tsx in the lbr_from_signext_quirk_needed() is
not required anymore.
Both LBR_FORMAT_EIP_FLAGS2 and LBR_FORMAT_INFO have LBR_TSX flag, but
only the LBR_FORMAT_EIP_FLAGS2 requirs the quirk. Update the comments
accordingly.
Fixes: 1ac7fd8159a8 ("perf/x86/intel/lbr: Support LBR format V7") Reported-by: Vince Weaver <vincent.weaver@maine.edu> Signed-off-by: Kan Liang <kan.liang@linux.intel.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20220714182630.342107-1-kan.liang@linux.intel.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tasks the are being deboosted from SCHED_DEADLINE might enter
enqueue_task_dl() one last time and hit an erroneous BUG_ON condition:
since they are not boosted anymore, the if (is_dl_boosted()) branch is
not taken, but the else if (!dl_prio) is and inside this one we
BUG_ON(!is_dl_boosted), which is of course false (BUG_ON triggered)
otherwise we had entered the if branch above. Long story short, the
current condition doesn't make sense and always leads to triggering of a
BUG.
Fix this by only checking enqueue flags, properly: ENQUEUE_REPLENISH has
to be present, but additional flags are not a problem.
Fixes: 64be6f1f5f71 ("sched/deadline: Don't replenish from a !SCHED_DEADLINE entity") Signed-off-by: Juri Lelli <juri.lelli@redhat.com> Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/20220714151908.533052-1-juri.lelli@redhat.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: f9aefd6b2aa3 ("net: warn if mac header was not set") Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Link: https://lore.kernel.org/bpf/20220707123900.945305-1-edumazet@google.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
mpol_set_nodemask()(mm/mempolicy.c) does not set up nodemask when
pol->mode is MPOL_LOCAL. Check pol->mode before access
pol->w.cpuset_mems_allowed in mpol_rebind_policy()(mm/mempolicy.c).
A KVM device cleanup happens in either of two callbacks:
1) destroy() which is called when the VM is being destroyed;
2) release() which is called when a device fd is closed.
Most KVM devices use 1) but Book3s's interrupt controller KVM devices
(XICS, XIVE, XIVE-native) use 2) as they need to close and reopen during
the machine execution. The error handling in kvm_ioctl_create_device()
assumes destroy() is always defined which leads to NULL dereference as
discovered by Syzkaller.
This adds a checks for destroy!=NULL and adds a missing release().
This is not changing kvm_destroy_devices() as devices with defined
release() should have been removed from the KVM devices list by then.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case a IRQ based transfer times out the bcm2835_spi_handle_err()
function is called. Since commit 1513ceee70f2 ("spi: bcm2835: Drop
dma_pending flag") the TX and RX DMA transfers are unconditionally
canceled, leading to NULL pointer derefs if ctlr->dma_tx or
ctlr->dma_rx are not set.
Fix the NULL pointer deref by checking that ctlr->dma_tx and
ctlr->dma_rx are valid pointers before accessing them.
Fixes: 1513ceee70f2 ("spi: bcm2835: Drop dma_pending flag") Cc: Lukas Wunner <lukas@wunner.de> Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Link: https://lore.kernel.org/r/20220719072234.2782764-1-mkl@pengutronix.de Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In rseq_test, there are two threads, which are vCPU thread and migration
worker separately. Unfortunately, the test has the wrong PID passed to
sched_setaffinity() in the migration worker. It forces migration on the
migration worker because zeroed PID represents the calling thread, which
is the migration worker itself. It means the vCPU thread is never enforced
to migration and it can migrate at any time, which eventually leads to
failure as the following logs show.
host# uname -r
5.19.0-rc6-gavin+
host# # cat /proc/cpuinfo | grep processor | tail -n 1
processor : 223
host# pwd
/home/gavin/sandbox/linux.main/tools/testing/selftests/kvm
host# for i in `seq 1 100`; do \
echo "--------> $i"; ./rseq_test; done
--------> 1
--------> 2
--------> 3
--------> 4
--------> 5
--------> 6
==== Test Assertion Failure ====
rseq_test.c:265: rseq_cpu == cpu
pid=3925 tid=3925 errno=4 - Interrupted system call
1 0x0000000000401963: main at rseq_test.c:265 (discriminator 2)
2 0x0000ffffb044affb: ?? ??:0
3 0x0000ffffb044b0c7: ?? ??:0
4 0x0000000000401a6f: _start at ??:?
rseq CPU = 4, sched CPU = 27
Fix the issue by passing correct parameter, TID of the vCPU thread, to
sched_setaffinity() in the migration worker.
Fixes: 61e52f1630f5 ("KVM: selftests: Add a test for KVM_RUN+rseq to detect task migration bugs") Suggested-by: Sean Christopherson <seanjc@google.com> Signed-off-by: Gavin Shan <gshan@redhat.com> Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Message-Id: <20220719020830.3479482-1-gshan@redhat.com> Reviewed-by: Andrew Jones <andrew.jones@linux.dev> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When building selftests out of the kernel tree the gpio.h the include
path is incorrect and the build falls back to the system includes
which may be outdated.
Add the KHDR_INCLUDES to the CFLAGS to include the gpio.h from the
build tree.
The cited commit refactored the flow action initialization sequence to
use an interface method when translating tc action instances to flow
offload objects. The refactored version skips the initialization of the
generic flow action attributes for tc actions, such as pedit, that allocate
more than one offload entry. This can cause potential issues for drivers
mapping flow action ids.
Populate the generic flow action fields for all the flow action entries.
Fixes: c54e1d920f04 ("flow_offload: add ops to tc_action_ops for flow action setup") Signed-off-by: Oz Shlomo <ozsh@nvidia.com> Reviewed-by: Roi Dayan <roid@nvidia.com>
----
v1 -> v2:
- coalese the generic flow action fields initialization to a single loop Reviewed-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_tcp_thin_linear_timeouts, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its reader.
Fixes: 36e31b0af587 ("net: TCP thin linear timeouts") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_tcp_recovery, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 4f41b1c58a32 ("tcp: use RACK to detect losses") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_tcp_early_retrans, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: eed530b6c676 ("tcp: early retransmit") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_udp_l3mdev_accept, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its reader.
Fixes: 63a6fff353d0 ("net: Avoid receiving packets with an l3mdev on unbound UDP sockets") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
sysctl_ip_prot_sock is accessed concurrently, and there is always a chance
of data-race. So, all readers and writers need some basic protection to
avoid load/store-tearing.
Fixes: 4548b683b781 ("Introduce a sysctl that modifies the value of PROT_SOCK.") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_fib_multipath_hash_fields, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: ce5c9c20d364 ("ipv4: Add a sysctl to control multipath hash fields") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_fib_multipath_hash_policy, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: bf4e0a3db97e ("net: ipv4: add support for ECMP hash policy choice") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dcss_dev_create() and dcss_dev_destroy(), we should call of_node_put()
in fail path or before the dcss's destroy as of_graph_get_port_by_id() has
increased the refcount.
Fixes: 9021c317b770 ("drm/imx: Add initial support for DCSS on iMX8MQ") Signed-off-by: Liang He <windhl@126.com> Reviewed-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com> Signed-off-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220714081337.374761-1-windhl@126.com Signed-off-by: Sasha Levin <sashal@kernel.org>
The value read from the "hpd-absent-delay-ms" property in DT was being
saved to the wrong variable, overriding the hpd_reliable delay. Fix the
typo.
Fixes: 5540cf8f3e8d ("drm/panel-edp: Implement generic "edp-panel"s probed by EDID") Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com> Reviewed-by: André Almeida <andrealmeid@igalia.com> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20220719203857.1488831-4-nfraprado@collabora.com Signed-off-by: Sasha Levin <sashal@kernel.org>
amt->nr_tunnels is protected by amt->lock.
But, amt_request_handler() has been using this variable without the
amt->lock.
So, it expands context of amt->lock in the amt_request_handler() to
protect amt->nr_tunnels variable.
Fixes: cbc21dc1cfe9 ("amt: add data plane of amt interface") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
AMT gateway interface should not receive unexpected multicast data.
Multicast data message type should be received after sending an update
message, which means all establishment between gateway and relay is
finished.
So, amt_multicast_data_handler() checks amt->status.
Fixes: cbc21dc1cfe9 ("amt: add data plane of amt interface") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
AMT gateway interface should not receive unexpected query messages.
In order to drop unexpected query messages, it checks nonce.
And it also checks ready4 and ready6 variables to drop duplicated messages.
Fixes: cbc21dc1cfe9 ("amt: add data plane of amt interface") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are some data races in the amt module.
amt->ready4, amt->ready6, and amt->status can be accessed concurrently
without locks.
So, it uses READ_ONCE() and WRITE_ONCE().
Fixes: cbc21dc1cfe9 ("amt: add data plane of amt interface") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
There are some synchronization issues(amt->status, amt->req_cnt, etc)
if the interface is in gateway mode because gateway message handlers
are processed concurrently.
This applies a work queue for processing these messages instead of
expanding the locking context.
So, the purposes of this patch are to fix exist race conditions and to make
gateway to be able to validate a gateway status more correctly.
When the AMT gateway interface is created, it tries to establish to relay.
The establishment step looks stateless, but it should be managed well.
In order to handle messages in the gateway, it saves the current
status(i.e. AMT_STATUS_XXX).
This patch makes gateway code to be worked with a single thread.
Now, all messages except the multicast are triggered(received or
delay expired), and these messages will be stored in the event
queue(amt->events).
Then, the single worker processes stored messages asynchronously one
by one.
The multicast data message type will be still processed immediately.
Now, amt->lock is only needed to access the event queue(amt->events)
if an interface is the gateway mode.
Fixes: cbc21dc1cfe9 ("amt: add data plane of amt interface") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fixes: 5fa6863ba692 ("spi: Check we have a spi_device_id for each DT compatible") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Link: https://lore.kernel.org/r/20220717135831.2492844-2-o.rempel@pengutronix.de Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Add spi_device_id entries to silent following warnings:
SPI driver sja1105 has no spi_device_id for nxp,sja1105e
SPI driver sja1105 has no spi_device_id for nxp,sja1105t
SPI driver sja1105 has no spi_device_id for nxp,sja1105p
SPI driver sja1105 has no spi_device_id for nxp,sja1105q
SPI driver sja1105 has no spi_device_id for nxp,sja1105r
SPI driver sja1105 has no spi_device_id for nxp,sja1105s
SPI driver sja1105 has no spi_device_id for nxp,sja1110a
SPI driver sja1105 has no spi_device_id for nxp,sja1110b
SPI driver sja1105 has no spi_device_id for nxp,sja1110c
SPI driver sja1105 has no spi_device_id for nxp,sja1110d
Fixes: 5fa6863ba692 ("spi: Check we have a spi_device_id for each DT compatible") Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220717135831.2492844-1-o.rempel@pengutronix.de Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
be_cmd_read_port_transceiver_data assumes that it is given a buffer that
is at least PAGE_DATA_LEN long, or twice that if the module supports SFF
8472. However, this is not always the case.
Fix this by passing the desired offset and length to
be_cmd_read_port_transceiver_data so that we only copy the bytes once.
regmap will sync a range of registers, here use the correct range
to make sure the sync do not touch other unexpected registers.
Find on pca9557pw on imx8qxp/dxl evk board, this device support
8 pin, so only need one register(8 bits) to cover all the 8 pins's
property setting. But when sync the output, we find it actually
update two registers, output register and the following register.
For the device use NO AI mode(not support auto address increment),
only use the single read/write when config the regmap.
We meet issue on PCA9557PW on i.MX8QXP/DXL evk board, this device
do not support AI mode, but when do the regmap sync, regmap will
sync 3 byte data to register 1, logically this means write first
data to register 1, write second data to register 2, write third data
to register 3. But this device do not support AI mode, finally, these
three data write only into register 1 one by one. the reault is the
value of register 1 alway equal to the latest data, here is the third
data, no operation happened on register 2 and register 3. This is
not what we expect.
Disable is done in stmmac_init_eee() on the event of MAC link down.
Since setting enable/disable EEE via ethtool will eventually trigger
a MAC down, removing this redunctant call in stmmac_ethtool.c to avoid
calling xpcs_config_eee() twice.
Fixes: d4aeaed80b0e ("net: stmmac: trigger PCS EEE to turn off on link down") Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com> Link: https://lore.kernel.org/r/20220715122402.1017470-1-vee.khee.wong@linux.intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The "ds" iterator variable used in dsa_port_reset_vlan_filtering() ->
dsa_switch_for_each_port() overwrites the "dp" received as argument,
which is later used to call dsa_port_vlan_filtering() proper.
As a result, switches which do enter that code path (the ones with
vlan_filtering_is_global=true) will dereference an invalid dp in
dsa_port_reset_vlan_filtering() after leaving a VLAN-aware bridge.
Use a dedicated "other_dp" iterator variable to avoid this from
happening.
Fixes: d0004a020bb5 ("net: dsa: remove the "dsa_to_port in a loop" antipattern from the core") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
In dsa_port_switchdev_unsync_attrs() there is a comment that resetting
the VLAN filtering isn't done where it is expected. And since commit 108dc8741c20 ("net: dsa: Avoid cross-chip syncing of VLAN filtering"),
there is no reason to handle this in switch.c either.
Therefore, move the logic to port.c, and adapt it slightly to the data
structures and naming conventions from there.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
The blamed refactoring commit changed a "port" iterator with "other_dp",
but still looked at the slave_dev of the dp outside the loop, instead of
other_dp->slave from the loop.
As a result, dsa_port_vlan_filtering() would not call
dsa_slave_manage_vlan_filtering() except for the port in cause, and not
for all switch ports as expected.
Fixes: d0004a020bb5 ("net: dsa: remove the "dsa_to_port in a loop" antipattern from the core") Reported-by: Lucian Banu <Lucian.Banu@westermo.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
This can be eventually be reproduced with the following script:
while :
do
echo 63 > /sys/class/net/<devname>/device/sriov_numvfs
sleep 1
echo 0 > /sys/class/net/<devname>/device/sriov_numvfs
sleep 1
done
Add lock when disabling SR-IOV to prevent process VF mailbox communication.
Fixes: d773d1310625 ("ixgbe: Fix memory leak when SR-IOV VFs are direct assigned") Signed-off-by: Piotr Skajewski <piotrx.skajewski@intel.com> Tested-by: Marek Szlosek <marek.szlosek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220715214456.2968711-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix an issue when driver incorrectly detects state
of recovery process and erroneously reinitializes interrupts,
which results in a kernel error and call trace message.
The issue was caused by a combination of two factors:
1. Assuming the EMP reset issued after completing
firmware recovery means the whole recovery process is complete.
2. Erroneous reinitialization of interrupt vector after detecting
the above mentioned EMP reset.
Fixes (1) by changing how recovery state change is detected
and (2) by adjusting the conditional expression to ensure using proper
interrupt reinitialization method, depending on the situation.
Fixes: 4ff0ee1af016 ("i40e: Introduce recovery mode support") Signed-off-by: Dawid Lukwinski <dawid.lukwinski@intel.com> Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Link: https://lore.kernel.org/r/20220715214542.2968762-1-anthony.l.nguyen@intel.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the SW bridge was trying to add/remove entries to/from HW, the
access to HW was not protected by any lock. In this way, it was
possible to have race conditions.
Fix this by using the lan966x->mac_lock to protect parallel access to HW
for this cases.
Fixes: 25ee9561ec622 ("net: lan966x: More MAC table functionality") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The problem with this spin lock is that it was just protecting the list
of the MAC entries in SW and not also the access to the MAC entries in HW.
Because the access to HW is indirect, then it could happen to have race
conditions.
For example when SW introduced an entry in MAC table and the irq mac is
trying to read something from the MAC.
Update such that also the access to MAC entries in HW is protected by
this lock.
Fixes: 5ccd66e01cbef ("net: lan966x: add support for interrupts from analyzer") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
To remove an entry to the MAC table, it is required first to setup the
entry and then issue a command for the MAC to forget the entry.
So if it happens for two threads to remove simultaneously an entry
in MAC table then it would be a race condition.
Fix this by using lan966x->mac_lock to protect the HW access.
To add an entry to the MAC table, it is required first to setup the
entry and then issue a command for the MAC to learn the entry.
So if it happens for two threads to add simultaneously an entry in MAC
table then it would be a race condition.
Fix this by using lan966x->mac_lock to protect the HW access.
Fixes: fc0c3fe7486f2 ("net: lan966x: Add function lan966x_mac_ip_learn()") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
When the HW deletes an entry in MAC table then it generates an
interrupt. The SW will go through it's own list of MAC entries and if it
is not found then it would notify the listeners about this. The problem
is that when the SW will go through it's own list it would take a spin
lock(lan966x->mac_lock) and when it notifies that the entry is deleted.
But to notify the listeners it taking the rtnl_lock which is illegal.
This is fixed by instead of notifying right away that the entry is
deleted, move the entry on a temp list and once, it checks all the
entries then just notify that the entries from temp list are deleted.
Fixes: 5ccd66e01cbe ("net: lan966x: add support for interrupts from analyzer") Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
The irqchip->irq_set_type method is called by __irq_set_trigger() under
the desc->lock raw spinlock.
The armada-37xx implementation, armada_37xx_irq_set_type(), takes a
plain spinlock, the kind that becomes sleepable on RT.
Therefore, this is an invalid locking scheme for which we get a kernel
splat stating just that ("[ BUG: Invalid wait context ]"), because the
context in which the plain spinlock may sleep is atomic due to the raw
spinlock. We need to go raw spinlocks all the way.
Replace the driver's irq_lock with a raw spinlock, to disable preemption
even on RT.
Commit 0651ab90e4ad ("ACPI: CPPC: Check _OSC for flexible address space")
changed _CPC probing to require flexible address space to be negotiated
for CPPC to work.
However it was observed that this caused a regression for Arek's ROG
Zephyrus G15 GA503QM which previously CPPC worked, but now it stopped
working.
To avoid causing a regression waive this failure when the CPU is known
to support CPPC.
Cc: Pierre Gondois <pierre.gondois@arm.com> Link: https://bugzilla.kernel.org/show_bug.cgi?id=216248 Fixes: 0651ab90e4ad ("ACPI: CPPC: Check _OSC for flexible address space") Reported-and-tested-by: Arek Ruśniak <arek.rusi@gmail.com> Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Extend iavf_state_str by strings for __IAVF_INIT_EXTENDED_CAPS and
__IAVF_INIT_CONFIG_ADAPTER.
Without this patch, when enabling debug prints for iavf.h, user will
see:
iavf 0000:06:0e.0: state transition from:__IAVF_INIT_GET_RESOURCES to:__IAVF_UNKNOWN_STATE
iavf 0000:06:0e.0: state transition from:__IAVF_UNKNOWN_STATE to:__IAVF_UNKNOWN_STATE
Fixes: 605ca7c5c670 ("iavf: Fix kernel BUG in free_msi_irqs") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Jun Zhang <xuejun.zhang@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix memory leak caused by not handling dummy receive descriptor properly.
iavf_get_rx_buffer now sets the rx_buffer return value for dummy receive
descriptors. Without this patch, when the hardware writes a dummy
descriptor, iavf would not free the page allocated for the previous receive
buffer. This is an unlikely event but can still happen.
Remove from supported_coalesce_params ETHTOOL_COALESCE_MAX_FRAMES
and ETHTOOL_COALESCE_MAX_FRAMES_IRQ. As tx-frames-irq allowed
user to change budget for iavf_clean_tx_irq, remove work_limit
and use define for budget.
Without this patch there would be possibility to change rx/tx-frames
and rx/tx-frames-irq, which for rx/tx-frames did nothing, while for
rx/tx-frames-irq it changed rx/tx-frames and only changed budget
for cleaning NAPI poll.
Fixes: fbb7ddfef253 ("i40evf: core ethtool functionality") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Jun Zhang <xuejun.zhang@intel.com> Tested-by: Marek Szlosek <marek.szlosek@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
Fix VLAN addition, so that PF driver does not reject whole VLAN batch.
Add VLAN reject handling, so rejected VLANs, won't litter VLAN filter
list. Fix handling of active_(c/s)vlans, so it will be possible to
re-add VLAN filters for user.
Without this patch, after changing trust to off, with VLAN filters
saturated, no VLAN is added, due to PF rejecting addition.
Fixes: 92fc50859872 ("iavf: Restrict maximum VLAN filters for VIRTCHNL_VF_OFFLOAD_VLAN_V2") Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_tcp_fastopen_blackhole_timeout, it can be changed
concurrently. Thus, we need to add READ_ONCE() to its readers.
Fixes: cf1ef3f0719b ("net/tcp_fastopen: Disable active side TFO in certain scenarios") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_tcp_fastopen, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
Fixes: 2100c8d2d9db ("net-tcp: Fast Open base") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Acked-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
While reading sysctl_igmp_llm_reports, it can be changed concurrently.
Thus, we need to add READ_ONCE() to its readers.
This test can be packed into a helper, so such changes will be in the
follow-up series after net is merged into net-next.
if (ipv4_is_local_multicast(pmc->multiaddr) &&
!READ_ONCE(net->ipv4.sysctl_igmp_llm_reports))
Fixes: df2cf4a78e48 ("IGMP: Inhibit reports for local multicast groups") Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Adjusted as per packet processor documentation.
This allows to properly match 'indev' for clsact rules.
Fixes: 47327e198d42 ("net: prestera: acl: migrate to new vTCAM api") Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
Socket destruction flow and tls_device_down function sync against each
other using tls_device_lock and the context refcount, to guarantee the
device resources are freed via tls_dev_del() by the end of
tls_device_down.
In the following unfortunate flow, this won't happen:
- refcount is decreased to zero in tls_device_sk_destruct.
- tls_device_down starts, skips the context as refcount is zero, going
all the way until it flushes the gc work, and returns without freeing
the device resources.
- only then, tls_device_queue_ctx_destruction is called, queues the gc
work and frees the context's device resources.
Solve it by decreasing the refcount in the socket's destruction flow
under the tls_device_lock, for perfect synchronization. This does not
slow down the common likely destructor flow, in which both the refcount
is decreased and the spinlock is acquired, anyway.
Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure") Reviewed-by: Maxim Mikityanskiy <maximmi@nvidia.com> Signed-off-by: Tariq Toukan <tariqt@nvidia.com> Reviewed-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Sasha Levin <sashal@kernel.org>
projects / linux-stable / log